BadgerCrusher_OperatingInstructions

7/31/2019 BadgerCrusher_OperatingInstructions

1/5

BICO BADGER 5" X 7" JAW CRUSHER

OPERATING INSTRUCTIONS

The Bico Badger Jaw Crusher is designed to give long and efficient service. In order to

secure the long life and excellent performance, which your crusher is capable of

delivering, it is essential that the following directions for operating and maintenance be

carefully observed.

The combination of Flat Faced Pulleys as supplied with V-belts on the BADGER was a

specially engineered arrangement for this machine. This combination has been in use for

many years in the manufacturing of this crushing equipment and has proven to be the

very best arrangement for machines such as these. When equipment is confronted with a

"SHOCK LOAD" condition, this safety factor allows just enough necessary "GIVE", and

prevents undue strain of metal-to-metal contact of the key, flywheel and eccentric shaft.

EYE, HEARING & DUST PROTECTION REQUIRED DURING OPERATION


2/5

INSTALLATION

If the crusher is not supplied with the optional stand and ore pan, then the machine should

be mounted securely, making sure there is adequate clearance underneath for sample or

material removal.

A licensed electrician according to all local codes and ordinances should do electrical

installation.

MACHINE ROTATION: Drive Wheels should rotate towards feed opening.

!! NEVER OPERATE MACHINE WITHOUT GUARDS AND FEED HOPPER!!

MAINTENANCE & ADJUSTMENTS

The jaws are preset at the factory to an approximate 1/4" space. Before starting the

crusher for the first time it is suggested to check this spacing.

JAW ADJUSTMENT

Two spring rods located on the back of the crusher control tension of the toggle. The hex

nut on the side of the frame adjusts the movable jaw gap.

To INCREASE the particle size adjust the large hex nut on lower frame counter-

clockwise to desired size. Re-tighten spring rods no more than hand tight.

To REDUCE the particle size, adjust the hex nut clockwise and re-check the spring rod

tension.

* CAUTION: IF SPRING RODS ARE TOO LOOSE THE TOGGLE WILL DROP

FROM MACHINE. TOO TIGHT WILL CAUSE EXCESSIVE WEAR!

Access the toggle through the maintenance access port on back of the crusher.

Jaws should not run in contact with each other.


3/5

MAINTENANCE

MAKE SURE THE UNIT IS DISCONNECTED FROM POWER

BEFORE SERVICING OR ACCESSING THE CRUSHER

Greasing is very important; with regular servicing it will extend the life of the machine.

Recommended heavy-duty #2 grease.

1. The jaw must be greased once every eight (8) hours of operation on the two nipples of

the movable jaw above toggle and below motor base.

2. Grease the two (2) side bearing nipples located on either side of the crusher. The

nipples have been extended up to make servicing easier. This should also be done everyeight (8) hours of operation.

3. Don't grease motor. This is a ball bearing motor and only requires grease after years of

operation.

4. The toggle should be periodically removed, cleaned and lubricated with a high

temperature wheel bearing or open gear lubricant.

5. The adjusting screw (grease nipple located on the Hex head adjusting nut) and the

adjusting block assembly (grease nipple located below the maintenance access port)

should be thoroughly lubricated monthly.


4/5

BICO INC. BADGER JAW CRUSHER PARTS

CATALOG# DESCRIPTION

B-1 WASHER (2 REQUIRED)

B-2 SHAFT

B-3N STATIONARY JAW PLATE - NI-HARD (SMOOTH)

B-3CA STATIONARY JAW PLATE - CHROME ALLOY (SMOOTH)

B-4 MOVEABLE JAW COMPLETE

B-6 WASHER (2 REQUIRED)

B-7 SPRING ROD ANCHOR

B-9 SIDE BEARING CAGE (2 REQUIRED)

B-10N MOVEABLE JAW PLATE - NI-HARD (SMOOTH)B-10CA MOVABLE JAW PLATE - CHROME ALLOY (GROOVED)

B-17 CHEEK PLATE (2 REQ)

B-20 TOGGLE BLOCK

B-22 MOTOR PLATE TENSION ROD

B-23 WEDGE BLOCK

B-24 ADJUSTING BLOCK

B-25 ADJUSTING SCREW

VD-112 ADJUSTING SCREW COLLAR

B-27 SPRING ROD (2 REQUIRED)

VD-88 SPRING FOR SPRING ROD

B-29 WING NUT FOR SPRING ROD

B-30 TOGGLE

B-41 SIDE BEARING CAGE SEAL (4 REQUIRED)

B-45 SIDE BEARING CAGE CAP BOLTS

B-47 MOVEABLE JAW BEARING (2 REQ) - SAME AS OLD# B-38

B-49 MOV. JAW BEARING CAGE WASHER (2 REQ) - SAME AS OLD

#B-5B-50 MOV. JAW BEARING CAGE - NOT SOLD SEPARATELY

B-51 MOVEABLE JAW BEARING CAGE CAP SEAL (2 REQUIRED)

B-55 SIDE JAW BEARING (2 REQUIRED)

B-56 ORE PAN ONLY


5/5

BICO INC. BADGER JAW CRUSHER PARTS

CATALOG# DESCRIPTION

B-57 DUST COLLECTION BASE & ORE PAN

B-130 COMBINATION FLYWHEEL (2 REQUIRED)

B-140 SAFETY GUARDS (SET OF 2)

B-146 FEED HOPPER

B-150 CAP SCREW F/ B-3 (1 REQ.)

WD-126 CAP SCREW F/B-10 (2 REQ.)

VD-129B CAP SCREW F/B-17 & B-20 - (B-17= 2/PLATE; B-20:4 REQ)VD-132 V-BELTS (8 REQUIRED)

BadgerCrusher_OperatingInstructions

Documents

Transcript of BadgerCrusher_OperatingInstructions