August 2012 ABB STOTZ-KONTAKT GmbH ABB i-bus KNX ......16 August 2012 | Slide 3 ABB i-bus® KNX EM/S...
18
© ABB 16 August 2012 | Slide 1 ABB STOTZ-KONTAKT GmbH ABB i-bus ® KNX Energy Module EM/S3.16.1 Energy Actuator SE/S3.16.1 August 2012
Transcript of August 2012 ABB STOTZ-KONTAKT GmbH ABB i-bus KNX ......16 August 2012 | Slide 3 ABB i-bus® KNX EM/S...
© ABB16 August 2012 | Slide 1
ABB STOTZ-KONTAKT GmbHABB i-bus® KNXEnergy Module EM/S3.16.1Energy Actuator SE/S3.16.1
August 2012
© ABB16 August 2012 | Slide 2
ABB i-bus® KNXEnergy Module and Energy Actuator
Energy Module EM/S3.16.1
Measures energy consumptionfor each channel
Measures instrument andpower values
Monitoring with thresholdvalues
Load Control (Master)
Energy Actuator SE/S3.16.1
In addition to the functions of theEM/S:
Functionality of the ABB i-bus® KNX Switch Actuators
Load Control Master and Slave
© ABB16 August 2012 | Slide 3
ABB i-bus® KNXEM/S 3.16.1 Energy Module
The Energy Module faciliates a detailed and transparent insight into the energy consumption of a building.
Measure energy consumption down to the consumer level.
The energy consumption is measured for each channel andfor the total device.
Every meter is assigned with an intermediate meter forindividual measuring tasks.
Monitoring of Instrument and Power Values
Active Power, Current, Voltage, Frequency and furthervalues are available
Load Control
The Energy Module can control up to 10 Energy Actuators.
© ABB16 August 2012 | Slide 4
ABB i-bus® KNXEM/S 3.16.1 Energy Module
Application
Active consumption measurement
Monitoring of electrical values
Benefits
Recording and representation of energy consumption ofindividual consumers
Enhancement of the Energy Efficiency
Product
Energy Module EM/S 3.16.1
© ABB16 August 2012 | Slide 5
ABB i-bus® KNXSE/S 3.16.1 Energy Actuator
The Energy Actuator faciliates additionally to the functionsof the Energy Module control of the connected consumerloads.
Switch reactions depending on thresholds, metering valuesand events
For every channel, the proven functionality of the ABB i-bus® KNX Switch Actuators is available.
The outputs can be configured as slaves in the Load Control
Instrument and Power Values can be monitored withthresholds.
© ABB16 August 2012 | Slide 6
ABB i-bus® KNXSE/S 3.16.1 Energy Actuator
Application
Active consumption measurement
Monitoring of electrical values
Switch Actuator, 3-fold
Benefits
Recording and representation of energy consumption ofindividual consumers
Enhancement of the Energy Efficiency
Intelligent control of the loads in the end circuit
Product
Energy Actuator SE/S 3.16.1
© ABB16 August 2012 | Slide 7
ABB i-bus® KNXFunctional Overview
© ABB16 August 2012 | Slide 8
ABB i-bus® KNXIndividual Functions
Meters
For every channel, the active energy consumption is measured continuously by a meter (Meter A...C).
The total consumption is also available (Meter total)
The meter values can be sent cyclically, on request or when a start or stop event occurs.
© ABB16 August 2012 | Slide 9
ABB i-bus® KNXIndividual Functions
Meters
Every meter is assigned with an intermediate meter, which can be parameterized for individual measuring tasks.
Each of the intermediate meters can be started by 1 bit objects or at a certain time received
Stopping by 1 bit object, time, duration or limit
© ABB16 August 2012 | Slide 10
ABB i-bus® KNXIndividual Functions
Instrument Values
Current, Voltage, Frequency
Power Values
Active Power, Apparent Power
Further Values
Crest Factor Current, Power Factor
© ABB16 August 2012 | Slide 11
ABB i-bus® KNXIndividual Functions
Load Control
SE/S or EM/S can be parameterized as Load ControlMaster.
Up to 10 Energy Actuators can be parameterized as slaves.
The Master receives Power Values from the slaves whichare summed up internally to the Power total.
If the power total exceeds a parameterized load limit, the master sends up to eight load shedding stages on the bus.
If a slave receives the shedding stage, it switches all outputs off with the respective shedding stage.
© ABB16 August 2012 | Slide 12
ABB i-bus® KNXIndividual Functions
© ABB16 August 2012 | Slide 13
ABB i-bus® KNXTechnical Data
© ABB16 August 2012 | Slide 14
ABB i-bus® KNXi-bus® Tool
Display and evaluate device information
Energy Actuator and Energy Module are both supported bythe i-bus® Tool
Display main and intermediate meters
Start, stop and reset intermediate meters
Display of the current power values for active power, apparent power and power factor as well as current, voltage, crest factor and frequency
Display of status values.
Switching of outputs is possible for the Energy Actuator.
© ABB16 August 2012 | Slide 15
ABB i-bus® KNXi-bus® Tool
Screenshot i-bus® Tool
© ABB16 August 2012 | Slide 16
ABB i-bus® KNXEnergy Monitoring
Save, display and evaluate energy and power values
Incorporates a preprepared ETS project for up to twelve Energy Actuators or Energy Modules as well as an appropriate fully functional visualization solution for representation and further processing of the detected measured values.
Functions:
Display of the main and intermediate meters
Starting and stopping the intermediate meter
Power monitor
Energy value monitor
Saving of the energy values as a .csv file
Permanent monitoring operation
© ABB16 August 2012 | Slide 17
ABB i-bus® KNXEnergy Monitoring
© ABB16 August 2012 | Slide 18
