ASSEMBLY INSTRUCTIONS

ITEM#: A101007603SKU# 810490347

ASHFORD 10X12 FTSOFT TOP GAZEBO

Need help? We are here for you! 1(866) 578-6569 24/7 • Toll Free

MAINTENANCE:

WARNINGS:

WARRANTY:

GENERAL BEST PRACTICES FOR ASSEMBLY:

WHAT IS COVERED ? The limited warranty is extended to the original purchaser and applies to material and manufacturer’s defect provided the item is maintained with care and used only for personal, residential purposes.Warranty: 1 Year

• Please read and understand this entire manual before attempting to assemble or install the product.• Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and

hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.• The assembled gazebo should be located at least 6 feet from any obstruction such as fence, garage, house, overhanging

branches, laundry lines or electrical wires.• Some parts may contain sharp edges. Wear protective gloves if necessary, during assembly.• This unit is heavy. For safety, do not assemble this item alone. Four people are recommended for safe assembly.• Check all nuts and bolts periodically for tightness and, when required, tighten them again.• Pay attention to the parts orientation

• Install the gazebo on level ground.Stakes are provided to secure the gazebo to the ground.• Do not assemble the gazebo on sandy, muddy or loose soil, as stakes do not have enough anchorage in these types of soil.• If you wish to secure the gazebo to a wood deck or concrete surface, use anchors suited to these surfaces.• Snow must be cleared off regularly during snowy days.Remove the snow at the roof top when it is thicker than 2 inches.

In order to avoid damage, use a plastic snow rake to remove excessive snow and ice buildup from roof and keepaway from falling debris.

• Do not leave the gazebo where there is a risk of high wind, as possible damage will occur to the structure.• Any assembly or maintenance of the product must be carried out by adults only.• Please check your state and local regulations prior to purchasing. Some jurisdictions may require permits for installation

and use. Some special procedures may be valid in your area.• Keep all flame and heat sources away from the tent fabric. This tent is made with fabric that meets CPAI-84

specifications for flame resistance. It is not fire proof. The fabric will burn if right in continuous contact with any flamesource. The application of any foreign substance to the tent fabric may render the flameresistant properties ineffective.

• If any scratch paint, please touch up to prevent rusting• For outdoor use only.

• Steel components for this gazebo are treated with rust inhibiting paint that protects it from rusting. However, due to thenature of steel, surface oxidation (rusting) will occur if these protective coatings are scratched. This is not a defect and thusnot covered by the warranty.

• To minimize this condition, it is recommended to use care when assembling and handling the product to prevent scratchingthe paint. Should any scratching or damage occur, it is recommended to cover the scratch immediately with rust inhibitingpaint (not included).

• Surface rust can also be easily removed with a very light application of regular cooking oil or WD-40. If surface oxidation(rusting) occurs and if no measure is taken to prevent this, the oxidation may start dripping onto deck or patio and causeddamaging stains, which may be difficult to remove. This can be prevented if the above-mentioned measures are taken tokeep the product from oxidizing.

• Do not use bleach, acid, or other abrasive cleaners on the roof or frame parts.• Keep instruction manual for future reference.• Keep the original packaging to store the gazebo.• Periodically check and ensure that all bolts are well-tighten during use

2/28

EXPLODED DRAWING

3/28

PARTS LIST

Label Part Number Description Qty Part Image

A P000200233 Post 4

B P000100151 Base 4

C P006100091 Base Cover 4

D1 P000400523 Long lef t Crossbeam 2

D2 P000400524 Long right Crossbeam 2

E1 P000400525 Short left Crossbeam 2

E2 P000400526 Short right Crossbeam 2

E3 P000500924 Beam connector 4

E4 P005600217 Beam Decorative parts 4

F P005600123 Decorative parts 4

G P005700212 Long Netting Tube 4

H P005700213 Short Netting Tube 4

I P000600733 Big Roof Sloping Beam 4

J P000600734 Sloping Beam Lower Tube 4

K P000600735 Long Middle Beam 2

L P000600736 Long Middle Beam Lower

Tube 2

M P000600737 Short Middle Beam 2

4/28

N P000600738 Short Middle Beam Lower

Tube 2

O P000500613 Sloping Beam connector 4

P P000500612 Middle Beam connector 4

Q P000500611 Big Roof Connector 1

R P000600732 Small Roof Sloping Beam 4

S P000500610 Small Roof Connector 1

T1 P005600122 Finial 1

T2 P000100150 Decorative cover 1

U P005800084 Hook 1

V1 P001100666 Small Canopy 1

W1 P001100665 Big Canopy 1

X1 P001200264 Mosquito Netting 1

Y1 P001300130 Curtain 1

5/28

HARDWARE LIST

Label Part Number Description Qty Add Part Image

AA M6*15 Bolt 88 5

BB H010030035 M6*40 Bolt 8 1

CC H050030001Flat washer

M6 104 5

DD H040010004 Nut M6 8 1

EE H050020017 Spring washer M6 8 1

FF H9900100009 Plastic Cup 40 2

HH H070010003Stake Φ8*180 8 0

II P005100264 Ring 104 6

Z1 H090030017 Wrench M6 2 0

Z2 H090030002 Allen Key M6 2 0

6/28

H010030030

HELPFUL HINTS

• Tools needed and not included

• Separating parts before starting

Provided in hardware pack

How many people needed for the installation work

7/28

STEP 1

Assembled View:

Insert the Base Cover(C) into the bottom of Post(A), then fixed the Base(B) with Bolt(AA) , Flat Washer(CC) by Allen Key (Z2)

8/28

STEP 2

Assembled View:

Insert the Beam Connector(E3) into Long Left Crossbeam(D1) and Short Left Crossbeam(E1), then fixed Netting Tube(G/H) to Long Left Crossbeam(D1) and Short Left Crossbeam(E1) with Bolt(AA), Flat Washer(CC) by Allen Key(Z2)

9/28

STEP 3

Assembled View:

Insert the Long Right Crossbeam(D2) and Short Right Crossbeam(E2) into Beam Connector(E3) , then fixed Netting Tube(G/H) to Long Right Crossbeam(D2) and Short

Bolt(AA),Right Crossbeam(E2) with Flat Washer(CC) by Allen Key(Z2)

10/28

STEP 4

Assembled View:

Fixed Beam Decorative Parts(E4) to Crossbeam(D2/D1/E2/E1), then fixed Middle Beam Connector(P) to Beam Decorative Parts(E4) with Bolt(AA), Flat Washer(CC) by Allen Key(Z2)

11/28

STEP 5

Assembled View:

Fixed the assembled Long Crossbeam(D1/D2) to Post(A) with Bolt(AA), Spring Washer(EE), Flat Washer(CC) and Plastic Cup(FF) by Allen Key(Z2), then put the assemblyed Short Crossbeam(E1/E2) beside

12/28

STEP 6

Assembled View:

Fixed the assemblyed Short Crossbeam(E1/E2) to the Post(A) with Bolt(AA), Spring Washer(EE), Flat Washer(CC) and Plastic Cup(FF) by Allen Key(z2)

13/28

STEP 7

Assembled View:

Fixed the Decorative Parts(F) to Post(A) with Bolt(AA), Flat Washer(CC) and Plastic Cup(FF) by Allen Key(Z2); Then fixed Sloping Beam Connector (O) to Decorative Part(F) and Post(A) with Bolt(AA), Flat Washer(CC) by Allen Key(Z2)

14/28

STEP 8

Assembled View:

Fixed Big Roof Sloping Beam(I) to Sloping Beam Lower Tube(J)

15/28

STEP 9

Assembled View:

Attach the upper of Big Roof Sloping Beam(I) to Big Roof Connector(Q). Fix Sloping Beam Lower Tube(J) to Sloping Beam Connector(O) with Bolt(BB), Flat Washer(CC)and Nut(DD) by Allen Key(Z2) and Wrench(Z1)

16/28

STEP 10

Assembled View:

Attach the Long Middle Beam(K) to Long Middle Beam Lower Tube(L)

17/28

STEP 11

Assembled View:

Attach the upper of Long Middle Beam(K) to Big Roof Connector(Q). Fix Long Middle Beam Lower Tube (L) to Middle Beam Connector(P) with Bolt(BB), Flat Washer(CC) and Nut(DD) by Allen Key(Z2) and Wrench(Z1).

18/28

STEP 12

Assembled View:

Attach Short Middle Beam(M) to Short Middle Beam Lower Tube(N)

19/28

STEP 13

Assembled View:

Attach the upper of Short Middle Beam(M) to Big Roof Connector(Q). Fix Short Middle Beam Lower Tube (N) to Middle Beam Connector(P) with Bolt(BB), Flat Washer(CC) and Nut(DD) by Allen Key(Z2) and Wrench(Z1).

20/28

STEP 14

Assembled View:

Spread the Big Canopy(W) to Big top, do not attached the canopy first.

21/28

STEP 15

Assembled View:

Attach Small Roof Sloping Beam(R) to Small Roof Connector(S)

22/28

STEP 16

Assembled View:

Attach the Small Canopy(V) to the Assembled small top; fix the Decorative Cover(T2) to Small Roof Connector, then tight them by Finial(T1)

23/28

STEP 17

Assembled View:

Attach the assembled Small top to Big top, then tight Small Roof Sloping Beam(R) and Big Roof Sloping Beam(I), then attach the Hook(U) to Big Roof Connector(Q).

24/28

STEP 18

Assembled View:

Attach the big canopy 's corner (without belt) to Sloping Beam Lower Tube(J), then attach the rest canopy corner(with belt) to the Sloping Beam Lower Tube(J), finally, attach the middle to the Long Middle Beam Lower Tube(L) and Short Middle Beam Lower Tube(N)

25/28

STEP 19

Assembled View:

1 1 Please do the matching of

zippers for different panels

as showing the picture

Attach Curtain(Y) to the outer side of Netting Tube(G/H) by Ring(II).

26/28

STEP 20

Assembled View:

1 1

Please do the matching of

zippers for different panels

as showing the picture

Attach the Mosquito Netting(X) to the inside of the Netting Tube(G/H) by Ring(II).

27/28

STEP 21

Assembled View:

Fix the Gazebo to the ground by Stake(HH)

28/28