Gazebo Kiosko1

5
Gazebo Assembly Manual Page 1 Lay out the parts. Here is what should be included: A 6 s id e ass em bl ie s, one o f whi ch is th e d oo r s ec ti on B 12 d ogb one s, 6 bot tom and 6 to p wi th p in ( the let ter on one matc hes the let ter on t he b ase and top of t he s ide panels) 24 screws are included for high wind areas. C 6 rafters with 6 zip ties for attachment D 9 gro up s of r oo f pur lo in s, 6 in ea ch bu nd le , c on ne ct ed wi th zi p t ie s E 1 cen te r r oof sup po rt bl oc k a nd 6 screws alo ng wi th he x wrenc h F 1 decorative cap and hook  G 2 box es of th at ch (66 squar e f eet) Stri ng fo r t ie in g i nc luded. Symphony Products 5601 Freedom Blvd. Aptos, CA 95003 (831)685-4722 F ax (83 1)661-0243 [email protected] www.symphonyproducts.com A B F E C D G Find the bundle of dogbones and make sure the letter on the parts match the letter on the ends of the sides. Lay out the parts, note the bottom dog bones have no pin in the center and the top dogbones have a dowel installed. B B A

Transcript of Gazebo Kiosko1

Page 1: Gazebo Kiosko1

8/8/2019 Gazebo Kiosko1

http://slidepdf.com/reader/full/gazebo-kiosko1 1/5

Gazebo Assembly Manual

Page 1

Lay out the parts. Here is what should be included:

A 6 side assemblies, one of which is the door section

B 12 dogbones, 6 bottom and 6 top with pin (the letter on one matches the letter on the base and top of the side

panels) 24 screws are included for high wind areas.

C 6 rafters with 6 zip ties for attachment

D 9 groups of roof purloins, 6 in each bundle, connected with zip ties

E 1 center roof support block and 6 screws along with hex wrench

F 1 decorative cap and hook 

G 2 boxes of thatch (66 square feet) String for tieing included.

Symphony Products

5601 Freedom Blvd.

Aptos, CA 95003

(831)685-4722 Fax (831)661-0243

[email protected]

www.symphonyproducts.com

A

B

F

E

C

D

GFind the bundle of dogbones and make

sure the letter on the parts match the letter

on the ends of the sides. Lay out the

parts, note the bottom dog bones have

no pin in the center and the top dogbones

have a dowel installed.

B

B

A

Page 2: Gazebo Kiosko1

8/8/2019 Gazebo Kiosko1

http://slidepdf.com/reader/full/gazebo-kiosko1 2/5

Gazebo Assembly Manual

Page 2

Stand up the first side. Do not place the door until last.

Place a bottom dogbone in the slot at the bottom of each

leg. Note that the slot goes on the inside of the gazebo.

Now find the next panel by checking the number at thebottom of each leg. For example K-4 sits next to K-3.

Now insert the top dogbone between the top of the

adjacent legs. Note that each dogbone is numbered tomatch. The top dogbone has a dowel pointing up. Once

the top is secure, the two panels will stand on their own.

Place each adjacent panel making sure that the

numbers match, and the slot and labels are toward

the inside. As each panel is placed, insert the top

and bottom dogbone in the ends of the legs.

Optional Step - For extra strength secure the

dogbones at both the top and bottom to the legs

with number 2 galvanized drywall screws. Use ahand or power screwdriver.

Page 3: Gazebo Kiosko1

8/8/2019 Gazebo Kiosko1

http://slidepdf.com/reader/full/gazebo-kiosko1 3/5

Gazebo Assembly Manual

Page 3

Find an area next to the gazebo to set up the roof structure. It

should be about the same area as the gazebo and have easy access

to the gazebo.

Place the round wood block (E) at the center of the area.

Find the roof rafters (C) and set around the perimeter. The end

with the hole close to the end goes in the center as shown. Each

rafter has a top and bottom. The gap between the holes is wider

on the top and each rafter should be set with the wide side up.

Each rafter also contains a mounting hole shown below. It faces

down. It does not matter what order you place the rafters.

Now locate the shortest group of roof 

purloins (D). There are 6 linked

together with zip ties. Link the rafters

together with the purloins. Begin to

tighten the zip ties.

Next insert and tighten the screws with

the hex wrench provided. Then tighten

up the zip ties.

Narrow Space = Bottom

Wide Space = Top

Hole at End = Center

Mounting Hole faces down

E

D

Page 4: Gazebo Kiosko1

8/8/2019 Gazebo Kiosko1

http://slidepdf.com/reader/full/gazebo-kiosko1 4/5

Gazebo Assembly Manual

Page 4

The top of the roof should be about 36” off 

the ground. You may place a support under

the block (E) to aid in assembly.

Now the remaining roof purloins will be

added one ring at a time, from the shortest to

the longest.

Snug down the zip ties on each group

when all are in place. Then cut off the

long unused end.

Page 5: Gazebo Kiosko1

8/8/2019 Gazebo Kiosko1

http://slidepdf.com/reader/full/gazebo-kiosko1 5/5

Gazebo Assembly Manual

Page 5

Pick up the rafter assembly by the rafters and lift the assembly

high enough to walk it into position over the gazebo.

As you bring the rafter

assembly to rest, place each

rafter onto the peg sticking

up from each dogbone.

Some adjustment of the

side pieces may be needed

to get all the holes to align.

Attach each rafter to the

dogbone with a zip tie.

Warning: climbing on the roof can be

dangerous. Use ladders and

scoffolding or seek professional help.

The thatch is attached by tieing a row

of thatch to each roof purloin. Tie the

thatch on the outside of the gazebo for

the nicest looking job. Start at the outer

edge and tie to the second purloin first,

all the way around. Then do the third

purloin, repeating all the way to the top.

Shorten the thatch used for the top row.

When finished the decorative cap is

attached at the peak. Traditionally

coconut string is used for tieing but any

string can be used.