ARIB STD-T64-C.S0011-C v2.0 Recommended …...1 Original Specification 2 This standard, ARIB...

ARIB STD-T64-C.S0011-C v2.0

Recommended Minimum Performance Standards for cdma2000 Spread Spectrum

Mobile Stations, Release C, Version 2.0

Refer to "Industrial Property Rights (IPR)" in the preface of ARIB STD-T64 for Related Industrial

Property Rights. Refer to "Notice" in the preface of ARIB STD-T64 for Copyrights

Original Specification 1

This standard, ARIB STD-T64-C.S0011-C v2.0, was prepared by 3GPP2-WG of Association of 2

Radio Industries and Businesses (ARIB) based upon the 3GPP2 specification, C.S0011 Release C, 3

Version 2.0. 4

5

Modification to the original specification 6

None. 7

8

Notes 9

None. 10

11

3GPP2 C.S0011-C

Date: December 06February 20, 20052006

Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations

Release C, Version 2.0 0.91

COPYRIGHT

3GPP2 and its Organizational Partners claim copyright in this document and individual Organizational Partners may copyright and issue documents or standards publications in individual Organizational Partner's name based on this document. Requests for reproduction of this document should be directed to the 3GPP2 Secretariat at [email protected]. Requests to reproduce individual Organizational Partner's documents should be directed to that Organizational Partner. See www.3gpp2.org for more information.

No text

3GPP2 C.S0011-C v2.0

CONTENTS

i

NORMATIVE REFERENCES ............................................................................................ xli 1

1 INTRODUCTION .......................................................................................................1-1 2

1.1 Scope..................................................................................................................1-1 3

1.2 Terms and Definitions.........................................................................................1-1 4

1.3 Test Modes........................................................................................................1-16 5

1.4 CDMA Equations ..............................................................................................1-17 6

1.4.1 Transmit Power of the Base Station.............................................................1-17 7

1.4.2 Received Signal Strength for Mobile Station Not in Handoff .........................1-18 8

1.4.2.1 Single-Path Case ...................................................................................1-18 9

1.4.2.2 Two-Path Case.......................................................................................1-20 10

1.4.2.3 Three-Path Case ....................................................................................1-21 11

1.4.3 Received Signal Strength for Mobile Station in Two-Way Handoff ................1-21 12

1.5 Tolerances ........................................................................................................1-22 13

1.5.1 CDMA System Parameter Tolerances...........................................................1-22 14

1.5.2 Measurement Tolerances.............................................................................1-22 15

1.6 Test Requirements for Mobile Stations Supporting Analog Operation ................1-22 16

1.6.1 Modulated Tone Frequency .........................................................................1-23 17

2 STANDARD RADIATED EMISSIONS MEASUREMENT PROCEDURE.........................2-1 18

2.1 Standard Radiation Test Site ..............................................................................2-1 19

2.2 Search Antenna ..................................................................................................2-1 20

2.3 Field-Strength Measurement...............................................................................2-2 21

2.4 Frequency Range of Measurements.....................................................................2-2 22

2.5 Test Ranges ........................................................................................................2-2 23

2.5.1 30-Meter Test Range .....................................................................................2-2 24

2.5.2 3-Meter Test Range .......................................................................................2-3 25

2.6 Radiated Signal Measurement Procedures ..........................................................2-3 26

3 CDMA RECEIVER MINIMUM STANDARDS...............................................................3-1 27

3.1 Frequency Coverage Requirements .....................................................................3-1 28

3.2 Acquisition Requirements ...................................................................................3-1 29

3.2.1 Idle Handoff Tests .........................................................................................3-1 30

3.2.1.1 Idle Handoff in Non-Slotted Mode on the Paging Channel ........................3-1 31

3GPP2 C.S0011-C v2.0

CONTENTS

ii

3.2.1.1.1 Definition............................................................................................3-1 1

3.2.1.1.2 Method of Measurement......................................................................3-1 2

3.2.1.1.3 Minimum Standard.............................................................................3-3 3

3.2.1.2 Idle Handoff in Slotted Mode on the Paging Channel ............................... 3-4 4

3.2.1.2.1 Definition............................................................................................3-4 5



3.2.1.3 Idle Handoff in Slotted Mode on the Forward Common Control 8

Channel .................................................................................................. 3-6 9

3.2.1.3.1 Definition............................................................................................3-6 10



3.2.1.4 Idle Handoff to Another Frequency .......................................................... 3-9 13

3.2.1.4.1 Definition............................................................................................3-9 14


3.2.1.4.3 Minimum Standard...........................................................................3-15 16

3.2.2 Soft Handoff Tests.......................................................................................3-15 17

3.2.2.1 Neighbor Set Pilot Detection and Incorrect Detection in Soft Handoff .... 3-15 18

3.2.2.1.1 Definition..........................................................................................3-15 19

3.2.2.1.2 Method of Measurement....................................................................3-15 20


3.2.2.2 Candidate Set Pilot Detection and Incorrect Detection in Soft 22

Handoff ................................................................................................. 3-20 23

3.2.2.2.1 Definition..........................................................................................3-20 24



3.2.2.3 Active Set Pilot Loss Detection in Soft Handoff ...................................... 3-23 27

3.2.2.3.1 Definition..........................................................................................3-23 28



3.2.3 Access and Access Probe Handoff Tests ......................................................3-26 31

3.2.3.1 Access Probe Handoff ............................................................................ 3-26 32

3GPP2 C.S0011-C v2.0

CONTENTS

iii

3.2.3.1.1 Definition ..........................................................................................3-26 1


3.2.3.1.3 Minimum Standard ...........................................................................3-29 3

3.2.3.2 Access Handoff ......................................................................................3-30 4

3.2.3.2.1 Definition ..........................................................................................3-30 5


3.2.3.2.3 Minimum Standard ...........................................................................3-32 7

3.2.4 Candidate Frequency Single Search ............................................................3-33 8

3.2.4.1 Definition ..............................................................................................3-33 9

3.2.4.2 Method of Measurement ........................................................................3-33 10

3.2.4.3 Minimum Standard ...............................................................................3-35 11

3.3 Forward Common Channel Demodulation Performance ....................................3-35 12

3.3.1 Demodulation of Non-Slotted Mode Paging Channel ....................................3-35 13

3.3.1.1 Definition ..............................................................................................3-36 14



3.3.2 Demodulation of Slotted Mode Paging Channel ...........................................3-37 17

3.3.2.1 Definition ..............................................................................................3-37 18



3.3.3 Demodulation of Broadcast Control Channel in AWGN Channel..................3-39 21

3.3.3.1 Definition ..............................................................................................3-39 22



3.3.4 Demodulation of Broadcast Control Channel in Multipath Fading 25

Channel ......................................................................................................3-40 26

3.3.4.1 Definition ..............................................................................................3-40 27



3.3.5 Demodulation of Forward Common Control Channel...................................3-42 30

3.3.5.1 Definition ..............................................................................................3-42 31

3GPP2 C.S0011-C v2.0

CONTENTS

iv

3.3.5.2 Method of Measurement........................................................................ 3-42 1

3.3.5.3 Minimum Standard ............................................................................... 3-43 2

3.3.6 Demodulation of Common Assignment Channel and Reception of 3

Common Power Control Channel ................................................................3-43 4

3.3.6.1 Definition .............................................................................................. 3-43 5



3.3.7 Demodulation of Forward Packet Data Control Channel in Additive White 8

Gaussian Noise ...........................................................................................3-45 9

3.3.7.1 Definition .............................................................................................. 3-45 10



3.3.8 Demodulation of Forward Packet Data Control Channel in Soft and 13

Softer Handoff.............................................................................................3-48 14

3.3.8.1 Definition .............................................................................................. 3-48 15



3.4 Forward Traffic Channel Demodulation Performance ........................................3-54 18

3.4.1 Demodulation of Forward Fundamental Channel in Additive White 19

Gaussian Noise ...........................................................................................3-54 20

3.4.1.1 Definition .............................................................................................. 3-54 21



3.4.2 Demodulation of Forward Fundamental Channel in Multipath Fading 24

Channel ......................................................................................................3-55 25

3.4.2.1 Definition .............................................................................................. 3-55 26



3.4.3 Demodulation of Forward Fundamental Channel During Soft Handoff........3-58 29

3.4.3.1 Definition .............................................................................................. 3-58 30



3GPP2 C.S0011-C v2.0

CONTENTS

v

3.4.4 Decision of Power Control Bit for Channels Belonging to Different Power 1

Control Sets During Soft Handoff ................................................................3-59 2

3.4.4.1 Definition ..............................................................................................3-59 3



3.4.5 Decision of Power Control Bit for Channels Belonging to the Same Power 6

Control Set..................................................................................................3-60 7

3.4.5.1 Definition ..............................................................................................3-60 8



3.4.6 Demodulation of Power Control Subchannel During Soft Handoff ...............3-62 11

3.4.6.1 Definition ..............................................................................................3-62 12



3.4.7 Demodulation of Forward Traffic Channel in Multipath Fading Channel 15

with Closed Loop Power Control (FPC_MODE = ‘000’) ..................................3-64 16

3.4.7.1 Definition ..............................................................................................3-64 17




with Closed Loop Power Control (FPC_MODE = ‘010’) ..................................3-66 21

3.4.8.1 Definition ..............................................................................................3-66 22




with Outer Loop Power Control and Closed Loop Power Control 26

(FPC_MODE = ‘000’, ‘001’ and ‘010’)............................................................3-67 27

3.4.9.1 Definition ..............................................................................................3-67 28




with Closed Loop Power Control (FPC_MODE = ‘000’) and Transmit 32

Diversity (OTD or STS).................................................................................3-69 33

3.4.10.1 Definition ..............................................................................................3-69 34

3GPP2 C.S0011-C v2.0

CONTENTS

vi





Diversity (OTD or STS) ................................................................................3-70 5

3.4.11.1 Definition .............................................................................................. 3-70 6



3.4.12 Demodulation of Power Control Subchannel During Reverse Pilot 9

Channel Gating...........................................................................................3-72 10

3.4.12.1 Definition .............................................................................................. 3-72 11



3.4.13 Demodulation of Power Control Subchannel During Reverse 14

Fundamental Channel Gating .....................................................................3-73 15

3.4.13.1 Definition .............................................................................................. 3-73 16



3.4.14 Demodulation of Forward Packet Data Channel in Additive White 19

Gaussian Noise ...........................................................................................3-73 20

3.4.14.1 Definition .............................................................................................. 3-74 21



3.4.15 Demodulation of Forward Packet Data Channel in Multipath Fading 24

Channel with no Power Control...................................................................3-75 25

3.4.15.1 Definition .............................................................................................. 3-75 26



3.5 Receiver Performance .......................................................................................3-76 29

3.5.1 Receiver Sensitivity and Dynamic Range .....................................................3-76 30

3.5.1.1 Definition .............................................................................................. 3-76 31



3GPP2 C.S0011-C v2.0

CONTENTS

vii

3.5.2 Single Tone Desensitization.........................................................................3-77 1

3.5.2.1 Definition ..............................................................................................3-77 2



3.5.3 Intermodulation Spurious Response Attenuation ........................................3-80 5

3.5.3.1 Definition ..............................................................................................3-80 6



3.5.4 Adjacent Channel Selectivity .......................................................................3-84 9

3.5.4.1 Definition ..............................................................................................3-85 10



3.5.5 Receiver Blocking Characteristics................................................................3-87 13

3.5.5.1 Definition ..............................................................................................3-87 14



3.6 Limitations on Emissions..................................................................................3-89 17

3.6.1 Conducted Spurious Emissions...................................................................3-89 18

3.6.1.1 Definition ..............................................................................................3-89 19



3.6.2 Radiated Spurious Emissions......................................................................3-90 22

3.6.2.1 Definition ..............................................................................................3-90 23



3.7 Supervision.......................................................................................................3-92 26

3.7.1 Paging Channel or Forward Common Control Channel................................3-92 27

3.7.1.1 Definition ..............................................................................................3-92 28



3GPP2 C.S0011-C v2.0

CONTENTS

viii

3.7.2 Forward Traffic Channel with Power Control Subchannel on F-FCH or F-1

DCCH .........................................................................................................3-94 2

3.7.2.1 Definition .............................................................................................. 3-94 3



3.7.3 Forward Traffic Channel with Power Control Subchannel on CPCCH ..........3-97 6

3.7.3.1 Definition .............................................................................................. 3-97 7



3.8 Channel Quality Measurement Performance.....................................................3-99 10

3.8.1 Forward Link Channel Quality Measurement Accuracy Test .......................3-99 11

3.8.1.1 Definition .............................................................................................. 3-99 12


3.8.1.3 Minimum Standard ............................................................................. 3-100 14

4 CDMA TRANSMITTER MINIMUM STANDARDS ........................................................4-1 15

4.1 Frequency Accuracy ...........................................................................................4-1 16

4.1.1 Definition......................................................................................................4-1 17

4.1.2 Method of Measurement ...............................................................................4-1 18

4.1.3 Minimum Standard.......................................................................................4-1 19

4.2 Handoff ..............................................................................................................4-2 20

4.2.1 CDMA to CDMA Hard Handoff ......................................................................4-2 21

4.2.1.1 Definition ................................................................................................ 4-2 22

4.2.1.2 Method of Measurement.......................................................................... 4-2 23

4.2.1.3 Minimum Standard ................................................................................. 4-3 24

4.2.2 Transmit Power after Hard Handoff...............................................................4-3 25

4.2.2.1 Definition ................................................................................................ 4-3 26

4.2.2.2 Method of Measurement.......................................................................... 4-5 27

4.2.2.3 Minimum Standard ................................................................................. 4-7 28

4.3 Modulation Requirements...................................................................................4-8 29

4.3.1 Time Reference .............................................................................................4-8 30

4.3.1.1 Definition ................................................................................................ 4-8 31

3GPP2 C.S0011-C v2.0

CONTENTS

ix

4.3.1.2 Method of Measurement ..........................................................................4-9 1


4.3.2 Reverse Pilot Channel to Code Channel Time Tolerance ..............................4-10 3

4.3.2.1 Definition ..............................................................................................4-10 4



4.3.3 Reverse Pilot Channel to Code Channel Phase Tolerance.............................4-11 7

4.3.3.1 Definition ..............................................................................................4-11 8



4.3.4 Waveform Quality and Frequency Accuracy.................................................4-11 11

4.3.4.1 Definition ..............................................................................................4-11 12



4.3.5 Code Domain Power ....................................................................................4-14 15

4.3.5.1 Definition ..............................................................................................4-14 16



4.4 RF Output Power Requirements........................................................................4-15 19

4.4.1 Range of Open Loop Output Power..............................................................4-15 20

4.4.1.1 Definition ..............................................................................................4-15 21


4.4.1.2.1 Access Channel .................................................................................4-16 23

4.4.1.2.2 Enhanced Access Channel ................................................................4-17 24


4.4.2 Time Response of Open Loop Power Control ................................................4-23 26

4.4.2.1 Definition ..............................................................................................4-23 27



4.4.3 Access Probe Output Power.........................................................................4-26 30

4.4.3.1 Definition ..............................................................................................4-26 31

3GPP2 C.S0011-C v2.0

CONTENTS

x


4.4.3.2.1 Access Channel Probe.......................................................................4-26 2

4.4.3.2.2 Enhanced Access Channel Probe ......................................................4-27 3


4.4.4 Range of Closed Loop Power Control ...........................................................4-28 5

4.4.4.1 Definition .............................................................................................. 4-28 6



4.4.5 Maximum RF Output Power........................................................................4-32 9

4.4.5.1 Definition .............................................................................................. 4-32 10



4.4.6 Minimum Controlled Output Power.............................................................4-40 13

4.4.6.1 Definition .............................................................................................. 4-40 14



4.4.7 Standby Output Power and Gated Output Power ........................................4-41 17

4.4.7.1 Definition .............................................................................................. 4-41 18



4.4.8 Power Up Function Output Power ...............................................................4-44 21

4.4.8.1 Definition .............................................................................................. 4-44 22



4.4.9 Code Channel to Reverse Pilot Channel Output Power Accuracy .................4-46 25

4.4.9.1 Definition .............................................................................................. 4-46 26


4.4.9.2.1 Code Channel Output Power for the Enhanced Access Channel 28

Header, Enhanced Access Channel Data, and Reverse Common 29

Control Channel Data .......................................................................4-46 30

4.4.9.2.2 Code Channel Output Power for the Reverse Traffic Channel ............4-48 31

3GPP2 C.S0011-C v2.0

CONTENTS

xi

4.4.9.2.3 Code Channel Output Power for the Reverse Channel Quality 1

Indicator Channel and the Reverse Acknowledgement Channel.........4-50 2


4.4.10 Reverse Pilot Channel Transmit Phase Discontinuity...................................4-53 4

4.4.10.1 Definition ..............................................................................................4-53 5



4.4.11 Reverse Traffic Channel Output Power During Changes in Data Rate..........4-55 8

4.4.11.1 Definition ..............................................................................................4-55 9



4.5 Limitations on Emissions..................................................................................4-57 12

4.5.1 Conducted Spurious Emissions...................................................................4-57 13

4.5.1.1 Definition ..............................................................................................4-57 14



4.5.1.3.1 Spreading Rate 1...............................................................................4-62 17

4.5.1.3.2 Spreading Rate 3...............................................................................4-67 18

4.5.2 Radiated Spurious Emissions......................................................................4-68 19

4.5.3 Occupied Bandwidth...................................................................................4-68 20

4.5.3.1 Definition ..............................................................................................4-68 21



5 CDMA ENVIRONMENTAL REQUIREMENTS .............................................................5-1 24

5.1 Temperature and Power Supply Voltage ..............................................................5-1 25

5.1.1 Definition ......................................................................................................5-1 26

5.1.2 Method of Measurement................................................................................5-1 27

5.1.3 Minimum Standard .......................................................................................5-2 28

5.2 High Humidity ....................................................................................................5-2 29

5.2.1 Definition ......................................................................................................5-2 30

5.2.2 Method of Measurement................................................................................5-3 31

3GPP2 C.S0011-C v2.0

CONTENTS

xii


5.3 Vibration Stability ..............................................................................................5-3 2

5.3.1 Definition......................................................................................................5-3 3



5.4 Shock Stability ...................................................................................................5-3 6

5.4.1 Definition......................................................................................................5-3 7



6 CDMA STANDARD TEST CONDITIONS ....................................................................6-1 10

6.1 Standard Equipment ..........................................................................................6-1 11

6.1.1 Basic Equipment ..........................................................................................6-1 12

6.1.2 Associated Equipment ..................................................................................6-1 13

6.2 Standard Environmental Test Conditions ...........................................................6-1 14

6.3 Standard Conditions for the Primary Power Supply ............................................6-1 15

6.3.1 General.........................................................................................................6-1 16

6.3.2 Standard DC Test Voltage from Accumulator Batteries .................................6-1 17

6.3.3 Standard AC Voltage and Frequency.............................................................6-2 18

6.4 Standard Test Equipment...................................................................................6-2 19

6.4.1 Standard Channel Simulator ........................................................................6-2 20

6.4.1.1 Channel Model Parameters ..................................................................... 6-2 21

6.4.1.2 Channel Model Parameter Conditions and Tolerances ............................. 6-4 22

6.4.1.3 Channel Simulator Configurations .......................................................... 6-5 23

6.4.2 Waveform Quality Measurement Equipment .................................................6-5 24

6.4.2.1 Rho Meter for Radio Configuration 1 and 2 ............................................. 6-5 25

6.4.2.2 Rho Meter for Radio Configuration 3 through 9 ....................................... 6-7 26

6.4.2.2.1 The Ideal Composite Reference Signal .................................................6-7 27

6.4.2.2.2 The Transmitter Signal-Under-Test .....................................................6-8 28

6.4.2.2.3 Active Code-Channel Identification, Symbol Detection and 29

Parameter Estimation .........................................................................6-9 30

6.4.2.2.4 Rho (ρ) ..............................................................................................6-10 31

3GPP2 C.S0011-C v2.0

CONTENTS

xiii

6.4.2.2.5 Code-domain Power (CDP).................................................................6-11 1

6.4.2.2.6 Power in Undesired Channels............................................................6-12 2

6.4.2.2.7 Code Domain Time Offsets and Phase Offsets Relative to Reverse 3

Pilot Channel.....................................................................................6-12 4

6.4.2.3 Code Domain Measurement Equipment Accuracy .................................6-13 5

6.4.3 Base Station Equipment..............................................................................6-13 6

6.4.3.1 Transmitter Equipment .........................................................................6-13 7

6.4.3.2 Receiver Equipment...............................................................................6-15 8

6.4.3.3 Protocol Support....................................................................................6-15 9

6.4.3.4 Timing Signals.......................................................................................6-15 10

6.4.4 AWGN Generator.........................................................................................6-16 11

6.4.5 CW Generator .............................................................................................6-17 12

6.4.6 Spectrum Analyzer ......................................................................................6-17 13

6.4.7 Average Power Meter ...................................................................................6-18 14

6.4.8 Phase Transient Measuring Equipment .......................................................6-19 15

6.5 Functional System Set-ups ...............................................................................6-19 16

6.5.1 Functional Block Diagrams .........................................................................6-19 17

6.5.2 General Comments......................................................................................6-21 18

6.6 Confidence Limits .............................................................................................6-32 19

6.6.1 Confidence Level of Error Rate ....................................................................6-32 20

6.6.2 Confidence on Power Measurement During Fading......................................6-36 21

6.6.3 Confidence Level of Detection Time .............................................................6-39 22

ANNEX A: SELECTED PERFORMANCE REQUIREMENTS TABLES.............................. A-1 23

A.1 Forward Common Channel Performance Tables ................................................. A-1 24

A.1.1 Non-Slotted Mode Paging Channel Performance Requirements......................A-1 25

A.1.1.1 Method of Measurement Test Parameters ............................................ A-1 26

A.1.1.2 Minimum Standards Requirements ..................................................... A-1 27

A.1.2 Slotted Mode Paging Channel Performance Requirements .............................A-2 28

A.1.2.1 Method of Measurement Test Parameters ............................................ A-2 29

A.1.2.2 Minimum Standards Requirements ..................................................... A-5 30

A.1.3 Forward Broadcast Control Channel Performance Requirements in 31

AWGN Channel .............................................................................................A-6 32

3GPP2 C.S0011-C v2.0

CONTENTS

xiv

A.1.3.1 Method of Measurement Test Parameters .............................................A-7 1

A.1.3.2 Minimum Standards Requirements ......................................................A-9 2

A.1.4 Forward Broadcast Control Channel Performance Requirements in 3

Multipath Fading Channel ..........................................................................A-11 4

A.1.4.1 Method of Measurement Test Parameters ...........................................A-12 5

A.1.4.2 Minimum Standards Requirements ....................................................A-32 6

A.1.5 Forward Common Control Channel Performance Requirements ..................A-41 7



A.1.6 Common Assignment Channel and Common Power Control Channel 10

Performance Requirements .........................................................................A-47 11



A.2 Forward Traffic Channel Demodulation Performance Tables .............................A-51 14

A.2.1 Forward Traffic Channel Performance Requirements in AWGN....................A-51 15



A.2.2 Forward Traffic Channel Performance Requirements in Multipath Fading 18

Channel ......................................................................................................A-91 19


A.2.2.2 Minimum Standards Requirements ..................................................A-101 21

A.2.3 Forward Fundamental Channel Performance Requirements During Soft 22

Handoff.....................................................................................................A-107 23

A.2.3.1 Method of Measurement Test Parameters .........................................A-107 24


A.2.4 Power Control Bit Performance Requirements for Channels Belonging to 26

Different Power Control Sets During Soft Handoff .....................................A-108 27



A.2.5 Power Control Bit Performance Requirements for Channels Belonging to 30

the Same Power Control Set......................................................................A-109 31



3GPP2 C.S0011-C v2.0

CONTENTS

xv

A.2.6 Power Control Subchannel Performance Requirements During Soft 1

Handoff .....................................................................................................A-109 2

A.2.6.1 Method of Measurement Test Parameters ........................................ A-110 3

A.2.6.2 Minimum Standards Requirements ................................................. A-110 4


Channel with Closed Loop Power Control (FPC_MODE = ‘000’) ..................A-110 6




Channel with Closed Loop Power Control (FPC_MODE = ‘010’) ..................A-121 10




Channel with Outer Loop Power Control and Closed Loop Power Control 14

(FPC_MODE = ‘000’, ‘001’ and ‘010’)..........................................................A-139 15





Diversity (OTD or STS)...............................................................................A-144 20





Diversity (OTD or STS)...............................................................................A-154 25



A.2.12 Power Control Subchannel Performance Requirements During Reverse 28

Pilot Channel Gating .................................................................................A-159 29



A.2.13 Power Control Subchannel Performance Requirements During Reverse 32

Fundamental Channel Gating ...................................................................A-160 33


3GPP2 C.S0011-C v2.0

CONTENTS

xvi


A.2.14 Forward Packet Data Channel Performance Requirements in Additive 2

White Gaussian Noise ...............................................................................A-162 3



A.2.15 Forward Packet Data Channel Performance Requirements in Multipath 6

Fading Channel with no Power Control .....................................................A-202 7



10

3GPP2 C.S0011-C v2.0

FIGURES

xvii

Figure 3.2.1.1.2-1. Idle Handoff in Non-Slotted Mode (Test 1).......................................... 3-3 1

Figure 3.2.1.1.2-2. Idle Handoff in Non-Slotted Mode (Test 2).......................................... 3-3 2

Figure 3.2.1.2.2-1. Slotted Mode Idle Handoff ................................................................. 3-6 3

Figure 3.2.1.3.2-1. Slotted Mode Idle Handoff ................................................................. 3-8 4

Figure 3.2.1.4.2-1. Idle Handoff to Another Frequency (Test 1)...................................... 3-14 5

Figure 3.2.1.4.2-2. Idle Handoff to Another Frequency (Test 2)...................................... 3-14 6

Figure 3.2.2.1.2-1. Neighbor Set Pilot Detection ............................................................ 3-18 7

Figure 3.2.2.1.2-2. Neighbor Set Pilot Incorrect Detection ............................................. 3-19 8

Figure 3.2.2.2.2-1. Candidate Set Pilot Detection (Test 1) .............................................. 3-22 9

Figure 3.2.2.2.2-2. Candidate Set Pilot Incorrect Detection (Test 2) ............................... 3-22 10

Figure 3.2.2.3.2-1. Active Set Pilot Loss Detection (Test 2) ............................................ 3-26 11

Figure 3.2.3.1.2-1. Access Probe Handoff ...................................................................... 3-29 12

Figure 3.2.3.2.2-1. Access Handoff................................................................................ 3-32 13

Figure 3.3.8.2-1. Forward Packet Data Channel Demodulation in Softer and Soft 14

Handoff (Tests 1 and 2) ........................................................................................... 3-51 15

Figure 3.3.8.2-2. Forward Packet Data Channel Demodulation in Softer Handoff 16

(Test 3).................................................................................................................... 3-52 17

Figure 3.3.8-3. Forward Packet Data Channel Demodulation in Soft Handoff (Test 4).... 3-52 18

Figure 3.4.6.2-1. Demodulation of Power Control Subchannel During Soft Handoff....... 3-64 19

Figure 4.4.2.3-1. Upper and Lower Limits for Open Loop Power Control Step 20

Response for ∆Pin = 20 dB ...................................................................................... 4-25 21

Figure 4.4.7.3-1. Transmission Envelope Mask (Average Gated-on Power Control 22

Group) .................................................................................................................... 4-44 23

Figure 6.4.1-1. Autocorrelation Coefficient of the Phase .................................................. 6-3 24

Figure 6.5.1-1. Functional Set-up for Traffic Channel Tests in Fading Channel............. 6-19 25

Figure 6.5.1-2. Functional Set-up for Traffic Channel Tests in Soft Handoff .................. 6-20 26

Figure 6.5.1-3. Functional Set-up for Searcher and Traffic Channel Tests in Soft 27

Handoff................................................................................................................... 6-20 28

Figure 6.5.1-4. Functional Set-up for Tests Without Fading .......................................... 6-21 29

Figure 6.5.1-5. Functional Set-up for Tests With Transmit Diversity ............................ 6-21 30

Figure 6.6.1-1. Ratio (Measured/Specified) Bound as a Function of Number of 31

Errors (k) for 95% Confidence ................................................................................. 6-34 32

3GPP2 C.S0011-C v2.0

FIGURES

xviii

Figure 6.6.1-2. Ratio (Measured/Specified) Bound as a Function of Number of 1

Errors (k) for 90% Confidence................................................................................. 6-34 2

Figure 6.6.1-3. Test Requirement for 95% Confidence of FER = 0.01............................. 6-35 3

Figure 6.6.1-4. Test Requirement for 95% Confidence of FER = 0.05............................. 6-35 4

Figure 6.6.1-5. Test Requirement for 95% Confidence of FER = 0.1............................... 6-36 5

Figure 6.6.1-6. Test Requirement for 90% Confidence of FER = 0.1............................... 6-36 6

7

3GPP2 C.S0011-C v2.0

TABLES

xix

Table 1.3-1. Test Configuration Combinations............................................................... 1-16 1

Table 3.2.1.1.2-1. Test Parameters for Idle Handoff in Non-Slotted Mode ........................ 3-2 2

Table 3.2.1.2.2-1. Test Parameters for Slotted Mode Idle Handoff .................................... 3-5 3

Table 3.2.1.3.2-1. Test Parameters for Slotted Mode Idle Handoff .................................... 3-8 4

Table 3.2.1.4.2-1. Test Parameters for Idle Handoff to Another Frequency..................... 3-13 5

Table 3.2.2.1.2-1. Test Parameters for Neighbor Set Pilot Detection (Test 1) .................. 3-17 6

Table 3.2.2.1.2-2. Test Parameters for Neighbor Set Pilot Detection (Test 2) .................. 3-17 7

Table 3.2.2.1.2-3. Test Parameters for Neighbor Set Pilot Incorrect Detection (Test 8

3) ............................................................................................................................ 3-18 9

Table 3.2.2.2.2-1. Test Parameters for Candidate Set Pilot Detection (Test 1) ................ 3-21 10

Table 3.2.2.2.2-2. Test Parameters for Candidate Set Pilot Incorrect Detection (Test 11

2) ............................................................................................................................ 3-21 12

Table 3.2.2.3.2-1. Test Parameters for Active Set Pilot Incorrect Loss Detection (Test 13

1) ............................................................................................................................ 3-25 14

Table 3.2.2.3.2-2. Test Parameters for Active Set Pilot Loss Detection (Test 2) ............... 3-25 15

Table 3.2.3.1.2-1. Test Parameters for Access Probe Handoff......................................... 3-28 16

Table 3.3.7.2-1. Test Parameters for Forward Packet Data Control Channel in 17

AWGN..................................................................................................................... 3-47 18

Table 3.3.7.3-1. Minimum Standards for Radio Configuration 10 Forward Packet 19

Data Control Channel Performance in AWGN.......................................................... 3-48 20

Table 3.3.8.2-1. Test Parameters for Forward Packet Data Channel Demodulation in 21

Soft and Softer Handoff........................................................................................... 3-51 22

Table 3.5.1.2-1. Test Parameters for Receiver Sensitivity and Dynamic Range............... 3-77 23

Table 3.5.2.2-1. Test Parameters for Single Tone Desensitization .................................. 3-79 24

Table 3.5.2.2-2. Minimum Effective Isotropic Radiated Power for Single Tone 25

Desensitization Test for Band Group 1900 ............................................................. 3-79 26

Table 3.5.2.2-3. Minimum Effective Radiated Power for Single Tone Desensitization 27

Test for Band Class 3.............................................................................................. 3-80 28

Table 3.5.3.2-1. Test Parameters for Band Groups 450 and 800 Intermodulation 29

Spurious Response Attenuation (Tests 1 and 2) ...................................................... 3-81 30

Table 3.5.3.2-2. Test Parameters for Band Class 1, 4, 8, 14 and 15 Intermodulation 31

Spurious Response Attenuation (Tests 1 and 2) ...................................................... 3-82 32

Table 3.5.3.2-3. Test Parameters for Band Class 6 Intermodulation Spurious 33

Response Attenuation (Tests 1 and 2) ..................................................................... 3-83 34

3GPP2 C.S0011-C v2.0

TABLES

xx





Table 3.5.4.2-1. Configuration for Interference Source .................................................. 3-86 5

Table 3.5.4.2-2. Test Parameters for Adjacent Channel Selectivity ................................ 3-86 6

Table 3.5.5.2-1. Test Parameters for Receiver Blocking Characteristics (In-Band) ......... 3-88 7

Table 3.5.5.2-2. Test Parameters for Receiver Blocking Characteristics (Out-Of-8

Band) ..................................................................................................................... 3-88 9

Table 3.6.2.3-1. Maximum Allowable Radiated Spurious Emissions for Band 10

Classes 0, 1, 7, 10, 14 and 15 ................................................................................ 3-91 11

Table 3.6.2.3-2. Maximum Allowable Radiated Spurious Emissions for Band 12

Classes 2, 3, 4, 5, 6, 8, 9, 11 and 12 ...................................................................... 3-91 13

Table 3.7.1.2-1. Test Parameters for Supervision of Paging Channel ............................. 3-93 14

Table 3.7.1.2-2. Test Parameters for Supervision of Forward Common Control 15

Channel.................................................................................................................. 3-94 16

Table 3.7.2.2-1. Test Parameters for Supervision of Forward Traffic Channel with 17

Power Control Subchannel on F-FCH or F-DCCH ................................................... 3-96 18

Table 3.7.3.2-1. Test Parameters for Supervision of Forward Traffic Channel with 19

Power Control Subchannel on CPCCH .................................................................... 3-98 20

Table 4.2.1.2-1. Test Parameters for CDMA to CDMA Hard Handoff................................ 4-3 21



Table 4.3.1.2-1. Test Parameters for Time Reference ..................................................... 4-10 24

Table 4.4.1.2.1-1. Test Parameter of Îor for Range of Open Loop Output Power for 25

the Access Channel ................................................................................................ 4-17 26


the Spreading Rate 1 Enhanced Access Channel .................................................... 4-19 28


the Spreading Rate 3 Enhanced Access Channel .................................................... 4-20 30

Table 4.4.1.3-1. Minimum Standards for Range of Open Loop Output Power for the 31

Access Channel ...................................................................................................... 4-21 32


Spreading Rate 1 Enhanced Access Channel .......................................................... 4-22 34

3GPP2 C.S0011-C v2.0

TABLES

xxi


Spreading Rate 3 Enhanced Access Channel .......................................................... 4-23 2

Table 4.4.2.2-1. Test Parameters for Time Response of Open Loop Power Control ......... 4-24 3

Table 4.4.5.2-1. Test Parameters for Maximum RF Output Power with a Single 4

Traffic Code Channel, Spreading Rate 1 .................................................................. 4-36 5

Table 4.4.5.2-2. Test Parameters for Maximum RF Output Power with Multiple 6

Traffic Code Channels, Spreading Rate 1 ................................................................ 4-36 7

Table 4.4.5.2-3. Îor Values for Maximum RF Output Power with Multiple Traffic 8

Code Channels, Spreading Rate 1 ........................................................................... 4-37 9

Table 4.4.5.2-4. Test Parameters for Maximum RF Output Power with a Single 10

Traffic Code Channel, Spreading Rate 3 .................................................................. 4-38 11

Table 4.4.5.2-5. Test Parameters for Maximum RF Output Power with Multiple 12

Traffic Code Channels, Spreading Rate 3 ................................................................ 4-38 13

Table 4.4.5.3-1. Effective Radiated Power at Maximum Output Power ........................... 4-39 14

Table 4.4.5.3-2. Maximum Output Power Backoff Allowances ....................................... 4-40 15

Table 4.4.6.2-1. Test Parameters for Minimum Controlled Output Power ...................... 4-41 16

Table 4.4.7.2-1. Test Parameters for Standby Output Power and Gated Output 17

Power...................................................................................................................... 4-43 18

Table 4.4.9.3-1. Code Channel Accuracy Requirements for the Reverse 19

Fundamental Channel and Reverse Dedicated Control Channel.............................. 4-52 20

Table 4.4.9.3-2. Code Channel Accuracy Requirements for the (Convolutional 21

Coded) Reverse Supplemental Channel ................................................................... 4-52 22

Table 4.4.9.3-3. Code Channel Accuracy Requirements for the (Turbo Coded) 23

Reverse Supplemental Channel............................................................................... 4-52 24

Table 4.4.9.3-4. Code Channel Accuracy Requirements for the 9600 bps Reverse 25

Fundamental Channel (or 9600 bps Reverse Dedicated Control Channel) Being 26

Transmitted in Addition to the (Convolutional Coded) Reverse Supplemental 27

Channel .................................................................................................................. 4-53 28

Table 4.4.9.3-5. Code Channel Accuracy Requirements for the 9600 bps Reverse 29

Fundamental Channel (or 9600 bps Reverse Dedicated Control Channel) Being 30

Transmitted in Addition to the (Turbo Coded) Reverse Supplemental Channel ........ 4-53 31

Table 4.5.1.2-1. Test Parameters for Testing Spurious Emissions with a Single 32

Traffic Code Channel at Maximum RF Output Power .............................................. 4-60 33

Table 4.5.1.2-2. Test Parameters for Testing Spurious Emissions with Multiple 34

Traffic Code Channels at Maximum RF Output Power............................................. 4-60 35

Table 4.5.1.2-3. Îor Values for Testing Spurious Emissions with Multiple Traffic 36

Code Channels at Maximum RF Output Power ....................................................... 4-61 37

3GPP2 C.S0011-C v2.0

TABLES

xxii

Table 4.5.1.3.1-1. Band Groups 450 and 800 Transmitter Spurious Emission Limits 1

for Spreading Rate 1 ............................................................................................... 4-62 2

Table 4.5.1.3.1-2. Band Group 1900 Transmitter Spurious Emission Limits for 3

Spreading Rate 1 .................................................................................................... 4-63 4

Table 4.5.1.3.1-3. Band Class 3 Transmitter Spurious Emission Limits for 5

Spreading Rate 1 .................................................................................................... 4-64 6

Table 4.5.1.3.1-4. Additional Band Class 6 Transmitter Spurious Emission Limits 7


Table 4.5.1.3.1-5. Additional Band Class 11 and 12 Transmitter Spurious Emission 9

Limits for Spreading Rate 1 .................................................................................... 4-66 10

Table 4.5.1.3.2-1. Transmitter Spurious Emission Limits for Spreading Rate 3............. 4-67 11

Table 4.5.1.3.2-2. Additional Band Class 6 Transmitter Spurious Emission Limits 12


Table 4.5.3.2-1. Test Parameters for Testing Occupied Bandwidth at Maximum RF 14

Output Power ......................................................................................................... 4-69 15

Table 5.1.1-1. Temperature Ranges................................................................................. 5-1 16

Table 6.4.1.3-1. Standard Channel Simulator Configurations ......................................... 6-5 17

Table 6.4.2.3-1. Accuracy of Code Domain Measurement Equipment............................ 6-13 18

Table A.1.1.1-1. Test Parameters for Non-Slotted Mode Paging Channel Performance 19

in AWGN................................................................................................................... A-1 20

Table A.1.1.2-1. Minimum Standards for Non-Slotted Mode Paging Channel 21

Performance in AWGN .............................................................................................. A-1 22

Table A.1.2.1-1. Test Parameters for Slotted Mode Paging Channel for Spreading 23

Rate 1 (Test 1) .......................................................................................................... A-2 24


Rate 1 (Test 2) .......................................................................................................... A-3 26


Rate 3 (Test 3) .......................................................................................................... A-4 28


Rate 3 (Test 4) .......................................................................................................... A-5 30

Table A.1.2.2-1. Minimum Standards for Slotted Mode Paging Channel Performance 31

for Spreading Rate 1 in AWGN (Test 1)...................................................................... A-5 32





3GPP2 C.S0011-C v2.0

TABLES

xxiii


for Spreading Rate 3 in AWGN (Test 4) ......................................................................A-6 2

Table A.1.3.1-1. Test Parameters for the Broadcast Control Channel in AWGN for 3

Spreading Rate 1 with Rate = 1/4 Code, No Transmit Diversity.................................A-7 4


Spreading Rate 1 with Rate = 1/2 Code, No Transmit Diversity.................................A-7 6


Spreading Rate 3 ......................................................................................................A-8 8

Table A.1.3.2-1. Minimum Standards for Broadcast Control Channel Performance in 9

AWGN for Spreading Rate 1 with R = 1/4 Code, No Transmit Diversity .....................A-9 10


AWGN for Spreading Rate 1 with R = 1/2 Code, No Transmit Diversity ...................A-10 12


AWGN for Spreading Rate 3 ....................................................................................A-11 14

Table A.1.4.1-1. Test Parameters for Broadcast Control Channel for Spreading Rate 15

1 with R = 1/4 Code, No Transmit Diversity ............................................................A-12 16
















1 with R = 1/4 Code, Orthogonal Transmit Diversity...............................................A-20 32

Table A.1.4.1-10. Test Parameters for Broadcast Control Channel for Spreading 33

Rate 1 with R = 1/4 Code, Orthogonal Transmit Diversity.......................................A-21 34


Rate 1 with R = 1/2 Code, Orthogonal Transmit Diversity.......................................A-22 36

3GPP2 C.S0011-C v2.0

TABLES

xxiv


Rate 1 with R = 1/2 Code, Orthogonal Transmit Diversity ...................................... A-23 2


Rate 1 with R = 1/4 Code, Space Time Spreading ................................................... A-24 4








Rate 3..................................................................................................................... A-28 12


Rate 3..................................................................................................................... A-29 14


Rate 3..................................................................................................................... A-30 16


Rate 3..................................................................................................................... A-31 18

Table A.1.4.2-1. Minimum Standards for Broadcast Control Channel Performance 19

for Spreading Rate 1 with R = 1/4 Code, No Transmit Diversity .............................. A-32 20








for Spreading Rate 3 ............................................................................................... A-40 28


for Spreading Rate 3 ............................................................................................... A-41 30

Table A.1.5.1-1. Test Parameters for the Forward Common Control Channel for 31

Spreading Rate 1 with Rate = 1/4 Mode, No Power Control, No Transmit 32

Diversity ................................................................................................................. A-42 33



Diversity ................................................................................................................. A-42 36

3GPP2 C.S0011-C v2.0

TABLES

xxv


Spreading Rate 3 with Rate = 1/4 Mode, No Power Control .....................................A-43 2



Table A.1.5.2-1. Minimum Standards for Forward Common Control Channel for 5


Diversity .................................................................................................................A-44 7



Diversity .................................................................................................................A-45 10





Table A.1.6.1-1. Test Parameters for the Common Assignment Channel for 15

Spreading Rate 1 with Rate = 1/4 mode in AWGN, No Transmit Diversity ...............A-48 16


Spreading Rate 1 with Rate = 1/2 mode in AWGN, No Transmit Diversity ...............A-49 18


Spreading Rate 3 in AWGN .....................................................................................A-49 20

Table A.1.6.2-1. Minimum Standards for Common Assignment Channel for 21

Spreading Rate 1 with Rate = 1/4 Mode in AWGN...................................................A-50 22

Table A.1.6.2-2 Minimum Standards for Common Assignment Channel for 23

Spreading Rate 1 with Rate = 1/2 Mode in AWGN...................................................A-50 24

Table A.1.6.2-3. Minimum Standards for Common Assignment Channel for 25

Spreading Rate 3 in AWGN .....................................................................................A-50 26

Table A.2.1.1-1. Test Parameters for Radio Configuration 1 Forward Fundamental 27

Channel in AWGN...................................................................................................A-51 28


Channel in AWGN...................................................................................................A-52 30


Channel in AWGN...................................................................................................A-52 32


Channel in AWGN...................................................................................................A-53 34


Channel or Forward Dedicated Control Channel with 100% Frame Activity in 36

AWGN.....................................................................................................................A-53 37

3GPP2 C.S0011-C v2.0

TABLES

xxvi



AWGN..................................................................................................................... A-54 3



AWGN..................................................................................................................... A-54 6



AWGN..................................................................................................................... A-55 9



AWGN..................................................................................................................... A-55 12



AWGN..................................................................................................................... A-56 15



AWGN..................................................................................................................... A-56 18



AWGN..................................................................................................................... A-57 21



AWGN..................................................................................................................... A-57 24



AWGN..................................................................................................................... A-58 27



AWGN..................................................................................................................... A-58 30



AWGN..................................................................................................................... A-59 33



AWGN..................................................................................................................... A-59 36



AWGN..................................................................................................................... A-60 39

3GPP2 C.S0011-C v2.0

TABLES

xxvii

Table A.2.1.1-19. Test Parameters for Radio Configuration 1 Forward Supplemental 1

Code Channel in AWGN ..........................................................................................A-60 2


Code Channel in AWGN ..........................................................................................A-61 4


Channel with 100% Frame Activity in AWGN with Convolutional Coding ................A-61 6


Channel with 100% Frame Activity in AWGN with Turbo Coding.............................A-62 8

























Table A.2.1.2-1. Minimum Standards for Radio Configuration 1 Forward 33

Fundamental Channel Performance in AWGN.........................................................A-69 34


Fundamental Channel Performance in AWGN.........................................................A-70 36

3GPP2 C.S0011-C v2.0

TABLES

xxviii


Fundamental Channel or Forward Dedicated Control Channel with 100% Frame 2

Activity Performance in AWGN................................................................................ A-71 3




















Supplemental Code Channel Performance in AWGN ............................................... A-77 23


Supplemental Code Channel Performance in AWGN ............................................... A-78 25


Supplemental Channel Performance with 100% Frame Activity in AWGN with 27

Convolutional Coding ............................................................................................. A-78 28



Turbo Coding.......................................................................................................... A-79 31



Convolutional Coding ............................................................................................. A-80 34



Turbo Coding.......................................................................................................... A-81 37

3GPP2 C.S0011-C v2.0

TABLES

xxix



Convolutional Coding..............................................................................................A-82 3



Turbo Coding ..........................................................................................................A-83 6






Turbo Coding ..........................................................................................................A-85 12






Turbo Coding ..........................................................................................................A-87 18






Turbo Coding ..........................................................................................................A-89 24


Supplemental Channel Performance in with 100% Frame Activity AWGN with 26




Turbo Coding ..........................................................................................................A-91 30

Table A.2.2.1-1. Test Parameters for Forward Fundamental Channel Radio 31

Configuration 1 in Fading Channel (Case 1) ............................................................A-92 32







3GPP2 C.S0011-C v2.0

TABLES

xxx


Configuration 1 in Fading Channel (Case 3)............................................................ A-96 2








Configuration 2 in Fading Channel (Case 6).......................................................... A-100 10

Table A.2.2.2-1. Minimum Standards for Fundamental Channel Performance in 11

Fading Channel (Case 1, Tests 1, 2 and 3) ............................................................ A-101 12


Fading Channel (Case 1, Test 4) ........................................................................... A-101 14


Fading Channel (Case 1, Test 5) ........................................................................... A-101 16


Fading Channel (Case 2)....................................................................................... A-102 18

Table A.2.2.2-5. Minimum Standards for Band Classes 0, 2, 3, 5, 7, 9, 10, 11 and 19

12 Fundamental Channel Performance in Fading Channel (Case 3, Test 12) ........ A-102 20

Table A.2.2.2-6. Minimum Standards for Band Group 1900 Fundamental Channel 21

Performance in Fading Channel (Case 3, Test 12) ................................................. A-103 22

Table A.2.2.2-7. Recommended Minimum Standards for Band Group 450 and 800 23

Fundamental Channel Performance in Fading Channel (Case 3, Test 12) ............. A-103 24

Table A.2.2.2-8. Recommended Minimum Standards for Band Group 1900 25

Fundamental Channel Performance in Fading Channel (Case 3, Test 12) ............. A-103 26

Table A.2.2.2-9. Minimum Standards for Fundamental Channel Radio 27

Configuration 2 Performance in Fading Channel (Case 4, Tests 13 and 14) .......... A-104 28


Configuration 2 Performance in Fading Channel (Case 5) ..................................... A-105 30


Configuration 2 Performance in Fading Channel (Case 6) ..................................... A-106 32

Table A.2.2.2-12. Recommended Minimum Standards for Band Group 450 and 800 33

Fundamental Channel Radio Configuration 2 Performance in Fading Channel 34

(Case 6, Tests 20, 21, 22, and 23)......................................................................... A-106 35

3GPP2 C.S0011-C v2.0

TABLES

xxxi

Table A.2.2.2-13. Recommended Minimum Standards for Band Group 1900 1

Fundamental Channel Radio Configuration 2 Performance in Fading Channel 2

(Case 6, Tests 20, 21, 22, and 23) .........................................................................A-107 3


Channel During Soft Handoff ................................................................................A-107 5


Fundamental Channel Performance During Soft Handoff ......................................A-108 7

Table A.2.4.1-1. Test Parameters for Decision of Power Control Bit for Different 8

Power Control Sets................................................................................................A-108 9

Table A.2.5.1-1. Test Parameters for Decision of Power Control Bit for the Same 10

Power Control Set .................................................................................................A-109 11

Table A.2.6.1-1. Test Parameters for Demodulation of Power Control Subchannel 12

During Soft Handoff ..............................................................................................A-110 13

Table A.2.7.1-1. Test Parameters for Forward Power Control .......................................A-111 14


Channel or Forward Dedicated Control Channel with 100% Frame Activity...........A-112 16







Table A.2.7.1-6. Test Parameters for Radio Configuration 3 Forward Dedicated 23

Control Channel with 10% Frame Activity.............................................................A-114 24







Table A.2.7.2-1 Minimum Standards for Radio Configuration 3 Forward 31


Activity..................................................................................................................A-116 33



Activity..................................................................................................................A-117 36

3GPP2 C.S0011-C v2.0

TABLES

xxxii



Activity ................................................................................................................. A-118 3



Activity ................................................................................................................. A-119 6

Table A.2.7.2-5 Minimum Standards for Radio Configuration 3 Forward Dedicated 7

Control Channel with 10% Frame Activity ............................................................ A-120 8







Table A.2.8.1-1. Test Parameters for Forward Power Control....................................... A-123 15


Channel with 100% Frame Activity (Part 1 of 2) .................................................... A-125 17








Channel with 100% Frame Activity ....................................................................... A-129 25




Supplemental Channel with 100% Frame Activity (Part 1 of 2).............................. A-131 29









3GPP2 C.S0011-C v2.0

TABLES

xxxiii


Supplemental Channel with 100% Frame Activity (Part 2 of 2) ..............................A-136 2





Table A.2.9.1-1. Test Parameters for Slow Power Control in Fading Channel ...............A-139 7











Activity..................................................................................................................A-142 18



Activity..................................................................................................................A-142 21



Activity..................................................................................................................A-143 24



Activity..................................................................................................................A-143 27

Table A.2.10.1-1. Test Parameters for Forward Power Control .....................................A-144 28


Channel or Forward Dedicated Control Channel (100% Frame Activity) with 30

Orthogonal Transmit Diversity ..............................................................................A-145 31



Space Time Spreading...........................................................................................A-146 34



Orthogonal Transmit Diversity ..............................................................................A-146 37

3GPP2 C.S0011-C v2.0

TABLES

xxxiv



Space Time Spreading .......................................................................................... A-147 3


Control Channel (10% Frame Activity) with Orthogonal Transmit Diversity........... A-147 5


Control Channel (10% Frame Activity) with Space Time Spreading ....................... A-148 7






Fundamental Channel or Forward Dedicated Control Channel (100% Frame 13

Activity) with Orthogonal Transmit Diversity......................................................... A-149 14



Activity) with Space Time Spreading ..................................................................... A-150 17



Activity) with Orthogonal Transmit Diversity......................................................... A-151 20



Activity) with Space Time Spreading ..................................................................... A-152 23

Table A.2.10.2-5. Minimum Standards for Radio Configuration 3 Forward Dedicated 24








Table A.2.11.1-1. Test Parameters for Forward Power Control..................................... A-155 32


Channel (100% Frame Activity) with Orthogonal Transmit Diversity ..................... A-156 34


Channel (100% Frame Activity) with Space Time Spreading.................................. A-156 36

3GPP2 C.S0011-C v2.0

TABLES

xxxv


Channel (100% Frame Activity) with Orthogonal Transmit Diversity......................A-157 2


Channel (100% Frame Activity) with Space Time Spreading ..................................A-157 4


Supplemental Channel (100% Frame Activity) with Orthogonal Transmit 6

Diversity ...............................................................................................................A-158 7


Supplemental Channel (100% Frame Activity) with Space Time Spreading............A-158 9


Supplemental Channel (100% Frame Activity) with Orthogonal Transmit 11

Diversity ...............................................................................................................A-159 12


Supplemental Channel (100% Frame Activity) with Space Time Spreading............A-159 14


during Reverse Pilot Channel Gating.....................................................................A-160 16


during Reverse Fundamental Channel Gating.......................................................A-160 18

Table A.2.14.1-1. Test Parameters for Radio Configuration 10 Forward Packet Data 19

Channel in AWGN.................................................................................................A-162 20


Channel in AWGN.................................................................................................A-163 22


Channel in AWGN.................................................................................................A-164 24


Channel in AWGN.................................................................................................A-165 26


Channel in AWGN.................................................................................................A-166 28


Channel in AWGN.................................................................................................A-167 30


Channel in AWGN.................................................................................................A-168 32


Channel in AWGN.................................................................................................A-169 34


Channel in AWGN.................................................................................................A-170 36


Channel in AWGN.................................................................................................A-171 38

3GPP2 C.S0011-C v2.0

TABLES

xxxvi


Channel in AWGN................................................................................................. A-172 2


Channel in AWGN................................................................................................. A-173 4


Channel in AWGN................................................................................................. A-174 6


Channel in AWGN................................................................................................. A-175 8


Channel in AWGN................................................................................................. A-176 10


Channel in AWGN................................................................................................. A-177 12


Channel in AWGN................................................................................................. A-178 14


Channel in AWGN................................................................................................. A-179 16


Channel in AWGN................................................................................................. A-180 18


Channel in AWGN................................................................................................. A-181 20


Channel in AWGN................................................................................................. A-182 22


Channel in AWGN................................................................................................. A-183 24

Table A.2.14.2-1. Minimum Standards for Radio Configuration 10 Forward Packet 25

Data Channel Performance in AWGN.................................................................... A-184 26











3GPP2 C.S0011-C v2.0

TABLES

xxxvii


Data Channel Performance in AWGN ....................................................................A-190 2

























Table A.2.15.1-1 Test Parameters for Radio Configuration 10 Forward Packet Data 27

Channel in Fading (Part 1 of 6) .............................................................................A-202 28









3GPP2 C.S0011-C v2.0

TABLES

xxxviii


Channel in Fading (Part 6 of 6) ............................................................................. A-207 2

Table A.2.15.2-1 Minimum Standards for Radio Configuration 10 Forward Packet 3

Data Channel in Fading (Part 1 of 3)..................................................................... A-208 4





9

3GPP2 C.S0011-C v2.0

xxxix

NOTES 1

1. “Base station” refers to the functions performed on the land side, which are 2

typically distributed among a cell, a sector of a cell, and a mobile communications 3

switching center. 4

2. This Standard uses the following verbal forms: “Shall” and “shall not” identify 5

requirements to be followed strictly to conform to the standard and from which no 6

deviation is permitted. “Should” and “should not” indicate that one of several 7

possibilities is recommended as particularly suitable, without mentioning or 8

excluding others; that a certain course of action is preferred but not necessarily 9

required; or that (in the negative form) a certain possibility or course of action is 10

discouraged but not prohibited. “May” and “need not” indicate a course of action 11

permissible within the limits of the standard. “Can” and “cannot” are used for 12

statements of possibility and capability, whether material, physical, or causal. 13

3. Unless indicated otherwise, this document presents numbers in decimal form. 14

Binary numbers are distinguished in the text by the use of single quotation marks. 15

4. Those wishing to deploy systems compliant with this Standard should also be 16

compliant with Parts 15, 22, 24, and 27 of [2] and with the applicable rules and 17

regulations of local administrations. 18

5. The following operators define mathematical operations: 19

× indicates multiplication. 20

/ indicates division. 21

+ indicates addition. 22

- indicates subtraction. 23

* indicates complex conjugation. 24

∈ indicates a member of the set. 25

x indicates the largest integer less than or equal to x: 1.1 = 1, 1.0 = 1. 26

|x| indicates the absolute value of x: |-17|=17, |17|=17. 27

6. All Radio Configuration 1 Eb/Nt requirements for Band Class 0 in this document 28

are based on measured data. For all other band classes, the radio configuration 29

Eb/Nt requirements in this document are based on simulated data with standard 30

margins of 1.3 dB for static and 1.5 dB for fading channel cases. Additional 31

Forward Fundamental Channel rate determination margins of 0.2, 0.3, and 0.4 dB 32

are added for the 1/2, 1/4, and 1/8 rate cases, respectively. An additional Forward 33

Supplemental Channel margin of 0.2 dB is added for Îor/Ioc equal to 6 and 8 dB 34

cases. Additional geometry dependent margins are added in Forward Packet Data 35

Channel test cases. Unless specified otherwise, the Forward Traffic Channel uses 36

20 ms long frame structures. 37

7. This Standard supports testing of mobile stations compliant with [4] and 38

subsequent revisions. 39

8. Tests in this revision reference the General Neighbor List Message, Universal 40

Neighbor List Message and the Universal Handoff Direction Message to maintain 41

3GPP2 C.S0011-C v2.0

xl

consistency with new tests that require the extended capability of these messages. 1

Where needed to test a P_REV six or lower mobile station, the Neighbor List 2

Message, Extended Neighbor List Message, and Extended Handoff Direction Message 3

may be used as specified in [6]. 4

9. For the test parameters tables, Îor is specified in terms of power spectral density in 5

a Spreading Rate 1 bandwidth. For testing applicable to Spreading Rate 3, the total 6

received power in a Spreading Rate 3 bandwidth is effectively 5 dB higher. 7

For the test parameters tables, Ec/Ior is specified in terms of the ratio in dB 8

between the energy accumulated over one PN chip period (Ec) to the total transmit 9

power spectral density in a Spreading Rate 1 bandwidth. For testing applicable to 10

Spreading Rate 3, Ec/Ior in a Spreading Rate 3 bandwidth is effectively 5 dB lower. 11

10. 10. Many tests in this revision specify using the Paging Channel for general test 12

setup requirements. If the mobile station does not support the Paging Channel, 13

then the Broadcast Control Channel and Forward Common Control Channel shall 14

be used in lieu of the Paging Channel. 15

11. The specification applies only to Band Classes 0 (Band Subclasses 0 and 1), 1, 2, 16

(Band Subclasses 0, 1, and 2), 3, 4, 5 (Band Subclasses 0 through 7), 6, 7, 8, 9, 10 17

(Band Subclasses 0 through 4), 11 (Band Subclasses 0 through 5), 12 (Band 18

Subclasses 0 and 1), 14, and 15 as defined in [17]. Operation with other band 19

classes and band subclasses may noy be supported by this specification. 20

21

22

3GPP2 C.S0011-C v2.0

xli

NORMATIVE REFERENCES 1

The following standards contain provisions which, through reference in this text, constitute 2

provisions of this Standard. At the time of publication, the editions indicated were valid. All 3

standards are subject to revision, and parties to agreements based on this Standard are 4

encouraged to investigate the possibility of applying the most recent editions of the 5

standards indicated below. ANSI and TIA maintain registers of currently valid national 6

standards published by them. 7

8

General References

1. ANSI C63.4-2003, American National Standard for Methods of Measurement of Radio–Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz, 2003.

2. CFR Title 47, Code of Federal Regulations, October 20052003.

9

10

3GPP2 Specifications and SDO Standards

3.

3GPP2: ARIB: STD-T64-C.S0002-D v1.0 CCSA: TIA: TIA/EIA-690 TTA: TTC:

Recommended Minimum Standards for 800-MHz Cellular Subscriber Units, 2000.

4.

3GPP2: C.S0002-D ARIB: STD-T64-C.S0002-D v1.0 CCSA: TIA: TIA-2000.2-D TTA: TTC:

Physical Layer Standard for cdma2000 Spread Spectrum Systems, 2004.

5.

3GPP2: C.S0004-D ARIB: CCSA: TIA: TIA-2000.4-D TTA: TTC:

Signaling Link Access Control (LAC) Standard for cdma2000 Spread Spectrum Systems, 2004.

6.


Upper Layer (Layer 3) Signaling Standard for cdma2000 Spread Spectrum Systems, 2004.

3GPP2 C.S0011-C v2.0

xlii

7.

3GPP2: C.S0010-C ARIB: CCSA: TIA: TIA-97-F TTA: TTC:

Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Base Stations, 2004.

8.

3GPP2: C.S0026-A ARIB: CCSA: TIA: TIA-870-A TTA: TTC:

Test Data Service Option (TDSO) for cdma2000 Spread Spectrum Systems, 2004.

9.

3GPP2: C.S0025 ARIB: STD-T64-C.S0025 CCSA: TIA: TIA/EIA/IS-871 TTA: TTC:

Markov Service Option (MSO) for cdma2000 Spread Spectrum Systems, 2001.

10.

3GPP2: C.S0013-A ARIB: STD-T64-C.S0013-A

CCSA: TIA: TIA/EIA-126-D TTA: TTC:

Loopback Service Options (LSO) for cdma2000 Spread Spectrum Systems, 2001.

11.

3GPP2: C.S0057 ARIB: STD-T64-C.S0057-0 v1.0 CCSA: TIA: TIA-1030 TTA: TTC:

Band Class Specification for cdma2000 Spread Spectrum Systems, 2004.

12.


Medium Access Control (MAC) Standard for cdma2000 Spread Spectrum Systems, 2004.

1

3GPP2 C.S0011-C v2.0

1-1

1 INTRODUCTION 1

1.1 Scope 2

This Standard details definitions, methods of measurement, and minimum performance 3

characteristics for Code Division Multiple Access (CDMA) mobile stations. This Standard 4

shares the purpose of [4] (and subsequent revision thereof) by ensuring that a mobile 5

station can obtain service in any cellular system that meets the compatibility requirements 6

of [4]. 7

Compatibility, as used in connection with this Standard and [4], is understood to mean 8

that any mobile station is able to place and receive calls in any CDMA system. Conversely, 9

all CDMA systems are able to place and receive calls with any CDMA mobile station 10

supporting operation in the same band. 11

Test methods are recommended in this document; however, methods other than those 12

recommended may suffice for the same purpose. 13

The performance metrics in this Standard require a mobile station to provide a single 14

antenna connector for testing. Mobile stations having multiple antenna, such as for receive 15

diversity, shall provide a single antenna connector for testing. If a mobile station has more 16

than one antenna connector, only one connector shall be used for testing. Additional 17

requirements specifically for multiple antenna configurations, i.e. receive diversity, are for 18

future study. 19

1.2 Terms and Definitions 20

Access Attempt. A sequence of one or more access probe sequences on the Access 21

Channel or Enhanced Access Channel containing the same message. See also Access 22

Probe, Access Probe Sequence, and Enhanced Access Probe. 23

Access Channel. A Reverse CDMA Channel used by mobile stations for communicating to 24

the base station. The Access Channel is used for short signaling message exchanges, such 25

as call originations, responses to pages, and registrations. The Access Channel is a slotted 26

random access channel. 27

Access Probe. One Access Channel transmission consisting of a preamble and a message. 28

The transmission is an integer number of frames in length, and transmits one Access 29

Channel message. See also Access Probe Sequence and Access Attempt. 30

Access Probe Sequence. A sequence of one or more access probes on the Access Channel 31

or Enhanced Access Channel. The same Access Channel or Enhanced Access Channel 32

message is transmitted in every access probe of an access attempt. See also Access Probe, 33

Enhanced Access Probe, and Access Attempt. 34

ACLR. Adjacent Channel Leakage power Ratio. 35

Active Frame. A frame that contains data and therefore is enabled in terms of traffic 36

power. 37

3GPP2 C.S0011-C v2.0

1-2

Additional Preamble. A preamble sent after the last fractional preamble on the Reverse 1

Pilot Channel prior to transmitting on the Enhanced Access Channel or the Reverse 2

Common Control Channel. 3

Adjacent Channel Leakage power Ratio. The ratio of the on-channel transmit power to 4

the power measured in one of the adjacent channels. 5

AWGN. Additive White Gaussian Noise. 6

Bad Frame. A frame classified with insufficient frame quality, or, for Radio Configuration 1, 7

9600 bps primary traffic only frame with bit errors. See also Good Frame. 8

Band Class (BC). A set of frequency channels and a numbering scheme for these channels. 9

Band Group 450. A collection of band classes that use the 450 MHz simulation results for 10

fading conditions. This group consists of Band Class 5 (450 MHz Band) and Band Class 11 11

(400 MHz European PAMR Band). 12

Band Group 800. A collection of band classes that use the 800 MHz simulation results for 13

fading conditions. This group consists of Band Class 0 (800 MHz Band), Band Class 2 14

(TACS Band), Band Class 3 (JTACS Band), Band Class 7 (700 MHz Band), Band Class 9 15

(900 MHz Band), Band Class 10 (Secondary 800 MHz Band), and 12 (800 MHz European 16

PAMR Band). 17

Band Group 1900. A collection of band classes that use the 1900 MHz simulation results 18

for fading conditions. This group consists of Band Class 1 (1900 MHz Band), Band Class 4 19

(Korean PCS Band), Band Class 6 (2 GHz Band), Band Class 8 (1800 MHz Band), Band 20

Class 14 (US 1900 MHz Band), and Band Class 15 (AWS Band). 21

22

Base Station. A fixed station used for communicating with mobile stations. Depending 23

upon the context, the term base station may refer to a cell, a sector within a cell, an MSC, 24

or other part of the wireless system. 25

Basic Access Mode. A mode used on the Enhanced Access Channel where a mobile station 26

transmits an Enhanced Access Channel preamble and Enhanced Access data in a method 27

similar to that used on the Access Channel. 28

BCCH_Chip_Bit. Number of PN chips per Broadcast Control Channel bit. For Spreading 29

Rate 1, BCCH_Chip_Bit is equal to 64 x v where v equals 1 when the data rate is 19200 30

bps, v equals 2 when the data rate is 9600 bps, and v equals 4 when the data rate is 4800 31

bps. For Spreading Rate 3, BCCH_Chip_Bit is equal to 192 x v where v equals 1 when the 32

data rate is 19200 bps, v equals 2 when the data rate is 9600 bps, and v equals 4 when the 33

data rate is 4800 bps. 34

orc

IEBCCH . The ratio of the average transmit energy per PN chip for the Broadcast Control 35

Channel to the total transmit power spectral density. 36

bps. Bits per second. 37

Broadcast Control Channel (BCCH). A code channel in a Forward CDMA Channel used 38

for transmission of control information from a base station to a mobile station. 39

3GPP2 C.S0011-C v2.0

1-3

CACH_Chip_Bit. Number of PN chips per Common Assignment Channel bit. For Spreading 1

Rate 1, CACH_Chip_Bit is equal to 128 for 9600 bps. For Spreading Rate 3, 2

CACH_Chip_Bit is equal to 384 for 9600 bps. 3

orc

IECACH . The ratio of the average transmit energy per PN chip for the Forward Common 4

Assignment Channel to the total transmit power spectral density. 5

Candidate Frequency. The frequency for which the base station specifies a search set, 6

when searching on other frequencies while performing mobile-assisted handoffs. 7

CDMA. See Code Division Multiple Access. 8

CDMA Channel. The set of channels transmitted between the base station and the mobile 9

stations within a given CDMA frequency assignment. See also Forward CDMA Channel and 10

Reverse CDMA Channel. 11

CDMA Channel Number. An 11-bit number corresponding to the center of the CDMA 12

frequency assignment. 13

CDMA Frequency Assignment. A 1.23 MHz or a 3.69 MHz segment of spectrum. For Band 14

Class 0, the channel is centered on one of the 30 kHz channels. For band classes 1, 4, 6, 7, 15

8 and 9, the channel is centered on one of the 50 kHz channels. For band classes 2, 3, 10, 16

11 and 12, the channel is centered on one of the 25 kHz channels. For Band Class 5, the 17

channel is centered on one of the 20 or 25 kHz channels. 18

CDMA Preferred Set. The set of CDMA channel numbers in a CDMA system corresponding 19

to frequency assignments that a mobile station will normally search to acquire a CDMA 20

Pilot Channel. 21

Chip Rate. Equivalent to the spreading rate of the channel. It is either 1.2288 Mcps or 22

3.6864 Mcps. 23

Code Channel. A subchannel of a Forward CDMA Channel or Reverse CDMA Channel. 24

Each subchannel uses an orthogonal Walsh function or quasi-orthogonal function. 25

Code Division Multiple Access (CDMA). A technique for spread-spectrum multiple-access 26

digital communications that creates channels through the use of unique code sequences. 27

Common Assignment Channel (CACH). A forward common channel used by the base 28

station to acknowledge a mobile station accessing the Enhanced Access Channel, and in 29

the case of Reservation Access Mode, to transmit the address of a Reverse Common Control 30

Channel and associated Common Power Control Subchannel. 31

Common Power Control Channel (CPCCH). A forward common channel which transmits 32

power control bits (i.e., common power control subchannels) to multiple mobile stations. 33

The Common Power Control Channel is used by mobile stations operating in the 34

Reservation Access Mode. 35

Common Power Control Subchannel. A subchannel on the Common Power Control 36

Channel used by the base station to control the power of a mobile station when operating 37

on the Enhanced Access Channel or when operating in the Reservation Access Mode on the 38

Reverse Common Control Channel. 39

3GPP2 C.S0011-C v2.0

1-4

Continuous Transmission. A mode of operation in which Discontinuous Transmission is 1

not permitted. 2

Convolutional Code. A type of error-correcting code. A code symbol can be considered as 3

the convolution of the input data sequence with the impulse response of a generator 4

function. 5

orc

IE CPCCH . The ratio of the average transmit energy per PN chip for the Common Power 6

Control Channel to the total transmit power spectral density. 7

CRC. See Cyclic Redundancy Code. 8

Cyclic Redundancy Code (CRC). A class of linear error detecting codes which generate 9

parity check bits by finding the remainder of a polynomial division. See also Frame Quality 10

Indicator. 11

dBc. The ratio (in dB) of the sideband power of a signal, measured in a given bandwidth at 12

a given frequency offset from the center frequency of the same signal, to the total inband 13

power of the signal. For CDMA, the total inband power of the signal is measured in a 1.23 14

MHz bandwidth around the center frequency of the CDMA signal for a Spreading Rate 1 15

CDMA signal and in a 3.69 MHz bandwidth around the center frequency of the CDMA 16

signal for a Spreading Rate 3 CDMA signal. 17

dBm. A measure of power expressed in terms of its ratio (in dB) to one milliwatt. 18

dBm/Hz. A measure of power spectral density. The ratio, dBm/Hz, is the power in one 19

Hertz of bandwidth, where power is expressed in units of dBm. 20

DCCH_Chip_Bit. The number of PN chips per Dedicated Control Channel bit, equal to 128 21

for Spreading Rate 1 and 384 for Spreading Rate 3. 22

DCCH Ec. Average energy per PN chip for one Forward Dedicated Control Channel. For the 23

case when the Forward Power Control Subchannel is assumed to be transmitted at the 24

same power level that is used for the 9600 bps or 14400 bps data rate, the average energy 25

per PN chip for one Forward Dedicated Control Channel is 1211 × (total Forward Dedicated 26

Control Channel energy per PN chip). The total Forward Dedicated Control Channel is 27

comprised of traffic data and a Forward Power Control Subchannel. 28

orc

IE DCCH . The ratio of the average transmit energy per PN chip for one Forward 29

Dedicated Control Channel to the total transmit power spectral density. 30

Discontinuous Transmission (DTX). A mode of operation in which a base station or a 31

mobile station switches its transmitter or a particular code channel on and off 32

autonomously. For the case of DTX operation on the Forward Dedicated Control Channel 33

when power control bits are carried on that channel, the Forward Power Control 34

Subchannel is still transmitted. 35

dBW. A measure of power expressed in terms of its ratio (in dB) to one watt. 36

Eb. Average energy of an information bit at the mobile station antenna connector. 37

3GPP2 C.S0011-C v2.0

1-5

tb

NE . The ratio in dB of the combined received energy per bit to the effective noise power 1

spectral density at the base station antenna connector (see 1.4). If channel simulator is 2

used, then tb

NE

is referenced at the input of the channel simulator. 3

Ec. Average energy accumulated over one PN chip period (Ec). 4

orc

IE . The ratio in dB between the energy accumulated over one PN chip period (Ec) to the 5

total transmit power spectral density. 6

Effective Isotropic Radiated Power (EIRP). The product of the power supplied to the 7

antenna and the antenna gain in a direction relative to an isotropic antenna. 8

Effective Radiated Power (ERP). The product of the power supplied to the antenna and 9

the antenna gain relative to a half-wave dipole in a given direction. 10

EIB. See Erasure Indicator Bit. 11

EIRP. See Effective Isotropic Radiated Power. 12

Enhanced Access Channel (EACH). A reverse channel used by the mobile for 13

communicating to the base station. The Enhanced Access Channel operates in the Basic 14

Access Mode, Power Controlled Access Mode, and Reservation Access Mode. It is used for 15

transmission of short messages, such as signaling, MAC messages, response to pages, and 16

call originations. It can also be used to transmit moderate-sized data packets. 17

Enhanced Access Channel Preamble. A non-data bearing portion of the Enhanced Access 18

probe sent by the mobile station to assist the base station in initial acquisition and channel 19

estimation. 20

Enhanced Access Data. The data transmitted while in the Basic Access Mode or Power 21

Controlled Access Mode on the Enhanced Access Channel or while in the Reservation Mode 22

on a Reverse Common Control Channel. 23

Enhanced Access Header. A frame containing access origination information transmitted 24

immediately after the Enhanced Access Channel preamble while in the Power Controlled 25

Access Mode or Reservation Access Mode. 26

Enhanced Access Probe. One Enhanced Access Channel transmission consisting of an 27

Enhanced Access Channel preamble, optionally an Enhanced Access header, and 28

optionally Enhanced Access data. See also Enhanced Access Probe Sequence. 29

Enhanced Access Probe Sequence. A sequence of one or more Enhanced Access probes 30

on the Enhanced Access Channel. See also Enhanced Access Probe. 31

ERP. See Effective Radiated Power. 32

F-PDCCH0. Forward Packet Data Control Channel 0. The first Forward Packet Data 33

Control Channel. See also Forward Packet Data Control Channel. 34

3GPP2 C.S0011-C v2.0

1-6

FCH_Chip_Bit. The number of PN chips per Fundamental Channel bit, equal to 1

1228800/rb for Spreading Rate 1 and 3686400/rb for Spreading Rate 3, where rb is the 2

data rate of the Fundamental Channel. 3

FCH Ec. Average energy per PN chip for one Forward Fundamental Channel. For the case 4

when the Forward Power Control Subchannel is assumed to be transmitted at the same 5

power level that is used for the 9600 bps or 14400 bps data rate, the following equations 6

apply: 7

For Radio Configuration 1, it is equal to v11

11+

× (total Forward Fundamental Channel 8

energy per PN chip), where v equals 1 for 9600 bps, v equals 2 for 4800 bps, v equals 4 for 9

2400 bps, and v equals 8 for 1200 bps traffic data rate. For Radio Configuration 2, it is 10

equal to v23

23+

× (total Forward Fundamental Channel energy per PN chip), where v equals 11

1 for 14400 bps, v equals 2 for 7200 bps, v equals 4 for 3600 bps, and v equals 8 for 1800 12

bps traffic data rate. The total Forward Fundamental Channel is comprised of traffic data 13

and a power control subchannel. For Radio Configurations 3, 4, 6, and 7, it is equal to 14

v1111

+× (total Forward Fundamental Channel energy per PN chip), where v equals 1 for 15

9600 bps, v equals 2 for 4800 bps, v equals 4 for 2700 bps, and v equals 8 for 1500 bps 16

traffic data rate. For Radio Configurations 5, 8, and 9, it is equal to v11

11+

× (total Forward 17

Fundamental Channel energy per PN chip), where v equals 1 for 14400 bps, v equals 2 for 18

7200 bps, v equals 4 for 3600 bps, and v equals 8 for 1800 bps traffic data rate. The total 19

Forward Fundamental Channel is comprised of traffic data and a Forward Power Control 20

Subchannel. 21

orc

IE FCH . The ratio of the average transmit energy per PN chip for one Forward 22

Fundamental Channel to the total transmit power spectral density. 23

FCCCH_Chip_Bit. Number of PN chips per Forward Common Control Channel bit. For 24

Spreading Rate 1, FCCCH_Chip_Bit is equal to 32 x v where v equals 1 when the data rate 25

is 38400 bps, v equals 2 when the data rate is 19200 bps, and v equals 4 when the data 26

rate is 9600 bps. For Spreading Rate 3, FCCCH_Chip_Bit is equal to 96 x v where v equals 27

1 when the data rate is 38400 bps, v equals 2 when the data rate is 19200 bps, and v 28

equals 4 when the data rate is 9600 bps. 29

orc

IE FCCCH . The ratio of the average transmit energy per PN chip for the Forward 30

Common Control Channel to the total transmit power spectral density. 31

FER. Frame Error Rate of Forward Traffic Channel. The value of FER may be estimated by 32

using Service Option 2, 9, 30, 31, 32, 54 or 55. 33

Forward CDMA Channel. A CDMA Channel from a base station to mobile stations. The 34

Forward CDMA Channel contains one or more code channels that are transmitted on a 35

CDMA frequency assignment using a particular pilot PN offset. 36

3GPP2 C.S0011-C v2.0

1-7

Forward Common Control Channel (FCCCH). A control channel used for the 1

transmission of digital control information from a base station to one or more mobile 2

stations. 3

Forward Dedicated Control Channel (F-DCCH). A portion of a Radio Configuration 3 4

through 9 Forward Traffic Channel used for the transmission of higher-level data, control 5

information, and power control information from a base station to a mobile station. 6

Forward Fundamental Channel (F-FCH). A portion of a Forward Traffic Channel which 7

carries a combination of higher-level data and power control information. 8

Forward Packet Data Channel (F-PDCH). A portion of a Forward Traffic Channel which 9

carries higher-level data. 10

Forward Packet Data Control Channel (F-PDCCH). A control channel used for the 11

transmission of the control information for the subpacket being transmitted on the Forward 12

Packet Data Channel or to transmit control information. 13

Forward Power Control Subchannel. A subchannel on the Forward Fundamental 14

Channel or Forward Dedicated Control Channel used by the base station to control the 15

power of a mobile station when operating on the Reverse Traffic Channel. 16

Forward Supplemental Channel (F-SCH). A portion of a Radio Configuration 3 through 9 17

Forward Traffic Channel which operates in conjunction with a Forward Fundamental 18

Channel or a Forward Dedicated Control Channel in that Forward Traffic Channel to 19

provide higher data rate services, and on which higher-level data is transmitted. 20

Forward Supplemental Code Channel (SCCH). A portion of a Radio Configuration 1 and 2 21

Forward Traffic Channel which operates in conjunction with a Forward Fundamental 22

Channel in that Forward Traffic Channel, and (optionally) with other Forward 23

Supplemental Code Channels to provide higher data rate services, and on which higher-24

level data is transmitted. 25

Forward Traffic Channel. One or more code channels used to transport user and 26

signaling traffic from the base station to the mobile station. See Forward Fundamental 27

Channel, Forward Dedicated Control Channel, Forward Supplemental Channel, Forward 28

Supplemental Code Channel, and Forward Packet Data Channel. 29

FPC_PRI_CHANs. Power Control Subchannel indicator set by the base station to indicate 30

whether the mobile station is to perform the primary inner loop estimation on the received 31

Forward Fundamental Channel or the Forward Dedicated Control Channel. 32

Frame. A basic timing interval in the system. For the Sync Channel, a frame is 26.666... 33

ms long. For the Access Channel, the Paging Channel, the Broadcast Control Channel, the 34

Forward Supplemental Code Channel, and the Reverse Supplemental Code Channel, a 35

frame is 20 ms long. For the Forward Supplemental Channel and the Reverse 36

Supplemental Channel, a frame is 20, 40, or 80 ms long. For the Enhanced Access 37

Channel, the Forward Common Control Channel, and the Reverse Common Control 38

Channel, a frame is 5, 10, or 20 ms long. For the Forward Fundamental Channel, Forward 39

Dedicated Control Channel, Reverse Fundamental Channel, and Reverse Dedicated Control 40

Channel, a frame is 5 or 20 ms long. For the Common Assignment Channel, a frame is 5 41

ms long. 42

3GPP2 C.S0011-C v2.0

1-8

Frame Activity. The ratio of the number of active frames to the total number of frames 1

during channel operation. 2

Frame Offset. A time skewing of Forward Traffic Channel or Reverse Traffic Channel 3

frames from System Time in integer multiples of 1.25 ms. 4

Frame Quality Indicator. The CRC check applied to 9.6 and 4.8 kbps Traffic Channel 5

frames of Radio Configuration 1, all Forward Traffic Channel frames for Radio 6

Configurations 2 through 9, all Reverse Traffic Channel frames for Radio Configurations 2 7

through 6, the Broadcast Control Channel, Common Assignment Channel, Enhanced 8

Access Channel, and the Reverse Common Control Channel. 9

GHz. Gigahertz (109 Hertz). 10

Good Frame. A frame not classified as a bad frame. See also Bad Frame. 11

Good Message. A received message is declared a good message if it is received with a 12

correct CRC. 13

Handoff. The act of transferring communication with a mobile station from one base 14

station to another. 15

Hard Handoff. A handoff characterized by a temporary disconnection of the Traffic 16

Channel. Hard handoffs occur when the mobile station is transferred between disjoint 17

Active Sets, the CDMA frequency assignment changes, the frame offset changes, or the 18

mobile station is directed from a CDMA Traffic Channel to an analog voice channel. See 19

also Soft Handoff. 20

HPSK. Hybrid phase shift keying. 21

I0. The total received power spectral density, including signal and interference, as 22

measured at the mobile station antenna connector. 23

Ioc. The power spectral density of a band-limited white noise source (simulating 24

interference from other cells) as measured at the mobile station antenna connector. For 25

test cases where multiple channels or cells are specified, this power spectral density does 26

not include power from these multiple channels or cells. 27

Ior. The total transmit power spectral density of the Forward CDMA Channel at the base 28

station antenna connector. For transmit diversity test cases, it shall be the total combined 29

transmit power spectral density of the Forward CDMA Channel from both the main and 30

transmit diversity base station antenna connectors. 31

Îor. The received power spectral density of the Forward CDMA Channel as measured at the 32

mobile station antenna connector. 33

kHz. Kilohertz (103 Hertz). 34

Mcps. Megachips per second (106 chips per second). 35

Mean Input Power. The total received calorimetric power measured in a specified 36

bandwidth at the antenna connector, including all internal and external signal and noise 37

sources. 38

3GPP2 C.S0011-C v2.0

1-9

Mean Output Power. The total transmitted calorimetric power measured in a specified 1

bandwidth at the antenna connector when the transmitter is active. 2

MER. Message Error Rate. MER = 1 - dtransmitte messages ofNumber

received messages good ofNumber . 3

MHz. Megahertz (106 Hertz). 4

Mobile Station. A station intended to be used while in motion or during halts at 5

unspecified points. Mobile stations include portable units (e.g., hand-held personal units) 6

and units installed in vehicles. 7

Mobile Station Class. Mobile station classes define mobile station characteristics, such as 8

slotted operation and transmission power. 9

ms. Millisecond (10-3 second). 10

MSC. See Mobile Switching Center. 11

N0. The effective inband noise or interference power spectral density. 12

N/A. Not applicable. 13

Non-Slotted Mode. An operation mode of the mobile station in which the mobile station 14

continuously monitors the Paging Channel. 15

N/S. Not specified. 16

Nt. The effective noise power spectral density at the mobile station antenna connector. 17

OCNS. See Orthogonal Channel Noise Simulator. 18

OCNS Ec. Average energy per PN chip for the OCNS. 19

orc

IEOCNS . The ratio of the average transmit energy per PN chip for the OCNS to the total 20

transmit power spectral density. 21

Orthogonal Channel Noise Simulator. A hardware mechanism used to simulate the users 22

on the other orthogonal channels of a Forward CDMA Channel. 23

Orthogonal Transmit Diversity (OTD). A forward link transmission method which 24

distributes forward link channel symbols among multiple antennas and spreads the 25

symbols with a unique Walsh or quasi-orthogonal function associated with each antenna. 26

OTD. See orthogonal transmit diversity. 27

Packet. Physical Layer protocol data unit. 28

Packet Error Rate (PER). For multiple transmissions, a packet is declared in error if it has 29

insufficient frame quality after the last re-transmission defined for that test. 30

Paging Channel (PCH). A code channel in a Forward CDMA Channel used for transmission 31

of control information and pages from a base station to a mobile station. 32

Paging_Chip_Bit. Number of PN chips per Paging Channel bit, equal to 128 × v where v 33

equals 1 when the data rate is 9600 bps and v equals 2 when the data rate is 4800 bps. 34

3GPP2 C.S0011-C v2.0

1-10

Paging Ec. Average energy per PN chip for the Paging Channel. 1

orc

IEPaging . The ratio of the average transmit energy per PN chip for the Paging Channel 2

to the total transmit power spectral density. 3

orc

IE CCHPD . The ratio of the average transmit energy per PN chip for the Forward Packet 4

Data Control Channel to the total transmit power spectral density. 5

orc

IE CHPD . The ratio of the average transmit energy per PN chip for the Forward Packet 6

Data Channel to the total transmit power spectral density. 7

PDCCH_Chip_Bit. The number of PN chips per Packet Data Control Channel bit, equal to 8

1228800/rb, where rb is the data rate of the Packet Data Control Channel. 9

PDCH_Chip_Bit. The number of PN chips per Packet Data Channel bit, equal to 10

1228800/rb, where rb is the data rate of the Packet Data Channel. 11

PER. See packet error rate. 12

Physical Layer. The part of the communication protocol between the mobile station and 13

the base station that is responsible for the transmission and reception of data. The physical 14

layer in the transmitting station is presented a frame and transforms it into an over-the-air 15

waveform. The physical layer in the receiving station transforms the waveform back into a 16

frame. 17

Piece-wise Linear FER Curve. An FER-versus-Eb/Nt curve in which the FER vertical axis 18

is in log scale and the Eb/Nt horizontal axis is in linear scale expressed in dB, obtained by 19

interpolating adjacent test data samples with straight lines. 20

Piece-wise Linear MER Curve. An MER-versus-Eb/Nt curve in which the MER vertical 21

axis is in log scale and the Eb/Nt horizontal axis is in linear scale expressed in dB, 22

obtained by interpolating adjacent test data samples with straight lines. 23

Pilot Channel. An unmodulated, direct-sequence spread spectrum signal transmitted by a 24

CDMA base station or mobile station. A pilot channel provides a phase reference for 25

coherent demodulation and may provide a means for signal strength comparisons between 26

base stations for determining when to handoff. 27

Pilot Ec. Average energy per PN chip for the Pilot Channel. 28

oc

IE Pilot . The ratio of the combined pilot energy per chip, Ec, to the total received power 29

spectral density (noise and signals), I0, of at most K usable multipath components at the 30

mobile station antenna connector (see 1.4). K is the number of demodulating elements 31

supported by the mobile station. 32

orc

IEPilot . The ratio of the average transmit energy per PN chip for the Pilot Channel to the 33

total transmit power spectral density. 34

3GPP2 C.S0011-C v2.0

1-11

Pilot PN Sequence. A pair of modified maximal length PN sequences used to spread the 1

Forward CDMA Channel and the Reverse CDMA Channel. Different base stations are 2

identified by different pilot PN sequence offsets. 3

PN. Pseudonoise. 4

PN Chip. One bit in the PN sequence. 5

PN Sequence. Pseudonoise sequence. A periodic binary sequence. 6

Power Control Bit. A bit sent on the Forward Power Control Subchannel, Reverse Power 7

Control Subchannel, or Common Power Control Subchannel to signal the mobile station or 8

base station to increase or decrease its transmit power. 9

Power Control Ec. Average energy per PN chip for the Forward Power Control Subchannel. 10

For the case when the Forward Power Control Subchannel is assumed to be transmitted at 11

the same power level that is used for the 9600 bps or 14400 bps data rate, the following 12

equations apply: 13

For Radio Configuration 1, it is equal to v11

v+

× (total Forward Fundamental Channel 14


2400 bps, and v equals 8 for 1200 bps traffic data rate. For Radio Configuration 2, it is 16

equal to v23

v+

× (total Forward Fundamental Channel energy per PN chip), where v equals 17

1 for 14400 bps, v equals 2 for 7200 bps, v equals 4 for 3600 bps, and v equals 8 for 1800 18

bps traffic data rate. For Radio Configurations 3, 4, 6, and 7, it is equal to v11

v+

× (total 19

Forward Fundamental Channel or Forward Dedicated Control Channel energy per PN chip), 20

where v equals 1 for 9600 bps, v equals 2 for 4800 bps, v equals 4 for 2700 bps, and v 21

equals 8 for 1500 bps traffic data rate. For Radio Configurations 5, 8, and 9, it is equal to 22

v11v+

× (total Forward Fundamental Channel or Forward Dedicated Control Channel 23


3600 bps, and v equals 8 for 1800 bps traffic data rate. The total Forward Fundamental 25

Channel or Forward Dedicated Control Channel is comprised of traffic data and a power 26

control subchannel. 27

orc

IEControlPower . The ratio of the average transmit energy per PN chip for the Forward 28

Power Control Subchannel to the total transmit power spectral density. 29

Power Control Group. A 1.25 ms interval on the Forward Traffic Channel, the Reverse 30

Traffic Channel, and the Reverse Pilot Channel. See also Power Control Bit. 31

Power Controlled Access Mode. A mode used on the Enhanced Access Channel where a 32

mobile station transmits an Enhanced Access preamble, an Enhanced Access header, and 33

Enhanced Access data in the Enhanced Access probe using closed loop power control. 34

Power Up Function (PUF). A method by which the mobile station increases its output 35

power to support location services. 36

3GPP2 C.S0011-C v2.0

1-12

ppm. Parts per million. 1

Preamble. See Access Channel preamble, Enhanced Access Channel preamble, Reverse 2

Common Control Channel preamble, and Reverse Traffic Channel Preamble. 3

Primary Paging Channel. The default code channel (code channel 1) assigned for paging 4

on a CDMA Channel. 5

Protocol Data Unit (PDU). Encapsulated data communicated between peer layers on the 6

mobile station and the base station. 7

PS. Pilot Strength. Also see Pilot Ec/I0. 8

PUF. See Power Up Function. 9

PUF Probe. One or more consecutive frames on the Reverse Traffic Channel within which 10

the mobile station transmits the PUF pulse. 11

PUF Pulse. Portion of PUF probe which may be transmitted at elevated output power. 12

PUF Target Frequency. The CDMA frequency to which the base station directs a mobile 13

station for transmitting the PUF probe. 14

QIB. See Quality Indicator Bit. 15

QPSK. Quadrature phase shift keying. 16

Quality Indicator Bit (QIB). A bit used in the Radio Configurations 3, 4, 5, and 6 Reverse 17

Power Control Subchannel to indicate signal quality on the Forward Dedicated Control 18

Channel. When the Forward Fundamental Channel is present, this bit is set the same as 19

the Erasure Indicator Bits. 20

Quick Paging Channel (QPCH). An uncoded, spread, and On-Off-Keying (OOK) modulated 21

spread spectrum signal sent by a base station to inform mobile stations operating in the 22

slotted mode during the idle state whether to receive the Forward Common Control 23

Channel or the Paging Channel starting in the next Forward Common Control Channel or 24

Paging Channel frame. 25

QPCH_Chip_Bit. Number of PN chips per Quick Paging Channel bit. For Spreading Rate 1, 26

Quick Paging_Chip_Bit is equal to 256 x v where v equals 1 when the data rate is 4800 bps 27

and v equals 2 when the data rate is 2400 bps. For Spreading Rate 3, Quick 28

Paging_Chip_Bit is equal to 768 x v where v equals 1 when the data rate is 4800 bps and v 29

equals 2 when the data rate is 2400 bps. 30

orc

IE QPCH . The ratio of the average transmit energy per PN chip for the Quick Paging 31

Channel to the total transmit power spectral density. 32

Radio Configuration (RC). A set of Forward Traffic Channel and Reverse Traffic Channel 33

transmission formats that are characterized by physical layer parameters such as 34

transmission rates, modulation characteristics, and spreading rate. 35

RC. See Radio Configuration. 36

Reservation Access Mode. A mode used on the Enhanced Access Channel and Reverse 37

Common Control Channel where a mobile station transmits an Enhanced Access preamble 38

3GPP2 C.S0011-C v2.0

1-13

and an Enhanced Access header in the Enhanced Access probe. The Enhanced Access data 1

is transmitted on a Reverse Common Control Channel using closed loop power control. 2

Reverse Acknowledgment Channel. A portion of a Reverse CDMA Channel used for the 3

transmission of acknowledgments from the mobile station to the base station in response 4

to the data received on the Forward Packet Data Channel and the Forward Packet Data 5

Control Channel. 6

Reverse CDMA Channel. The CDMA Channel from the mobile station to the base station. 7

From the base station’s perspective, the Reverse CDMA Channel is the sum of all mobile 8

station transmissions on a CDMA frequency assignment. 9

Reverse Channel Quality Indicator Channel. A portion of a Reverse CDMA Channel used 10

by the mobile station to indicate to the base station the quality of the Forward Link Pilot 11

Channel received at the mobile station, and to indicate switching between base stations. 12

Reverse Common Control Channel. A portion of a Reverse CDMA Channel used for the 13

transmission of digital control information from one or more mobile stations to a base 14

station. It can be power and may support soft handoff. 15

Reverse Dedicated Control Channel (R-DCCH). A portion of a Radio Configuration 3 16

through 6 Reverse Traffic Channel used for the transmission of higher-level data and 17

control information from a mobile station to a base station. 18

Reverse Fundamental Channel (R-FCH). A portion of a Reverse Traffic Channel which 19

carries higher-level data and control information from a mobile station to a base station. 20

Reverse Pilot Channel (R-PICH). An unmodulated, direct-sequence spread spectrum 21

signal transmitted continuously by a CDMA mobile station. A reverse pilot channel 22

provides a phase reference for coherent demodulation and may provide a means for signal 23

strength measurement. 24

Reverse Power Control Subchannel. A subchannel on the Reverse Pilot Channel used by 25

the mobile station to control the power of a base station when operating on the Forward 26

Traffic Channel with Radio Configurations 3 through 9. 27

Reverse Supplemental Channel (R-SCH). A portion of a Radio Configuration 3 through 6 28

Reverse Traffic Channel which operates in conjunction with the Reverse Fundamental 29

Channel or the Reverse Dedicated Control Channel in that Reverse Traffic Channel to 30

provide higher data rate services, and on which higher-level data is transmitted. 31

Reverse Traffic Channel. A traffic channel on which data and signaling are transmitted 32

from a mobile station to a base station. The Reverse Traffic Channel is composed of up to 33

one Reverse Dedicated Control Channel, up to one Reverse Fundamental Channel, zero to 34

two Reverse Supplemental Channels, and zero to seven Reverse Supplemental Code 35

Channels. 36

RF Carrier. A direct-sequence spread RF channel. For the Forward CDMA Channel, the 37

number of RF carriers is equal to the Spreading Rate; for the Reverse CDMA Channel, there 38

is one RF carrier. 39

RMS. Root of Mean Square. 40

3GPP2 C.S0011-C v2.0

1-14

SCCH_Chip_Bit. The number of PN chips per Supplemental Code Channel bit, equal to 1


data rate of the Supplemental Code Channel. 3

SCH_Chip_Bit. The number of PN chips per Supplemental Channel bit, equal to 4


data rate of the Supplemental Channel. 6

SCCH Ec. Average energy per PN chip for one Forward Supplemental Code Channel. 7

SCH Ec. Average energy per PN chip for one Forward Supplemental Channel. 8

orc

IE SCCH . The ratio of the average transmit energy per PN chip for one Forward 9

Supplemental Code Channel to the total transmit power spectral density. 10

orc

IE SCH . The ratio of the average transmit energy per PN chip for one Forward 11

Supplemental Channel to the total transmit power spectral density. 12

Service Option 2. Loopback service option for Radio Configuration 1 as specified in [10]. 13

Service Option 9. Loopback service option for Radio Configuration 2 as specified in [10]. 14

Service Option 30. Mobile station data loopback test mode for Multiplex Option 1 15

Supplemental Channel as specified in [10]. 16

Service Option 31. Mobile station data loopback test mode for Multiplex Option 2 17

Supplemental Channel as specified in [10]. 18

Service Option 32. Test data service option for Radio Configurations 3 through 6 on the 19

Reverse Traffic Channel and Radio Configurations 3 through 9 on the Forward Traffic 20

Channel as specified in [8]. 21

Service Option 54. Markov service option for Radio Configurations 1 through 6 on the 22



Service Option 55. Loopback service option for Radio Configurations 1 through 6 on the 25



Serving Frequency. The CDMA frequency on which a mobile station is currently 28

communicating with one or more base stations. 29

Slotted Mode. An operation mode of the mobile station in which the mobile station 30

monitors only selected slots on the Paging Channel. 31

Soft Handoff. A handoff occurring while the mobile station is in the Mobile Station Control 32

on the Traffic Channel State. This handoff is characterized by commencing communications 33

with a new base station on the same CDMA frequency assignment before terminating 34

communications with the old base station. See Hard Handoff. 35

3GPP2 C.S0011-C v2.0

1-15

Space Time Spreading (STS). A forward link transmission method which transmits all 1

forward link channel symbols on multiple antennas and spreads the symbols with 2

complementary Walsh or quasi-orthogonal functions. 3

Spreading Rate (SR). The PN chip rate of the Forward CDMA Channel or the Reverse 4

CDMA Channel, defined as a multiple of 1.2288 Mcps. 5

Spreading Rate 1. Spreading Rate 1 is often referred to as “1X.” A Spreading Rate 1 6

Forward CDMA Channel uses a single direct-sequence spread carrier with a chip rate of 7

1.2288 Mcps. A Spreading Rate 1 Reverse CDMA Channel uses a single direct-sequence 8

spread carrier with a chip rate of 1.2288 Mcps. 9

Spreading Rate 3. Spreading Rate 3 is often referred to as “3X.” A Spreading Rate 3 10

Forward CDMA Channel uses three direct-sequence spread carriers each with a chip rate 11

of 1.2288 Mcps. A Spreading Rate 3 Reverse CDMA Channel uses a single direct-sequence 12

spread carrier with a chip rate of 3.6864 Mcps. 13

SR. See Spreading Rate. 14

STS. See Space Time Spreading. 15

Symbol. See Code Symbol and Modulation Symbol. 16

Sync Channel. Code channel 32 in the Forward CDMA Channel, which transports the 17

synchronization message to the mobile station. 18

Sync_Chip_Bit. Number of PN chips per Sync Channel bit, equal to 1024. 19

Sync Ec. Average energy per PN chip for the Sync Channel. 20

orc

IESync . The ratio of the average transmit energy per PN chip for the Sync Channel to 21

the total transmit power spectral density. 22

Target Frequency. The CDMA frequency assignment to which the base station directs a 23

mobile station in a handoff using an Extended Handoff Direction Message, a General 24

Handoff Direction Message, or a Universal Handoff Direction Message. 25

TD. Transmit Diversity schemes, including OTD and STS. 26

orc

IE Pilot TD . The ratio of the average transmit energy per PN chip for the Transmit 27

Diversity Pilot Channel to the total transmit power spectral density. 28

Time Reference. A reference established by the mobile station that is synchronous with 29

the earliest arriving multipath component used for demodulation. 30

Traffic Channel. A communication path between a mobile station and a base station used 31

for user and signaling traffic. The term Traffic Channel implies a Forward Traffic Channel 32

and Reverse Traffic Channel pair. See also Forward Traffic Channel and Reverse Traffic 33

Channel. 34

Traffic Ec. See DCCH Ec and FCH Ec. 35

3GPP2 C.S0011-C v2.0

1-16

orc

IE Traffic . See

orc

IE DCCH

and or

cI

E FCH . For Radio Configuration 1 and 2, the term 1

applies to the Fundamental Channel. For Radio Configuration 3 through 9, the term 2

applies both to the Fundamental Channel and Dedicated Control Channel. 3

Turbo Code. A type of error-correcting code. A code symbol is based on the outputs of the 4

two recursive convolutional codes (constituent codes) of the Turbo code. 5

Valid Power Control Bit. A valid power control bit is sent on the Forward Power Control 6

Subchannel in the second power control group following the corresponding Reverse Traffic 7

Channel power control group which was not gated off and in which the signal strength was 8

estimated. See 3.1.3.1.10 of [4]. 9

Walsh Function. One of 2N time orthogonal binary functions (note that the functions are 10

orthogonal after mapping ‘0’ to 1 and ‘1’ to -1). 11

1.3 Test Modes 12

The Forward Traffic Channel is verified by invoking Fundamental Channel test modes, 13

Dedicated Control Channel test modes, Supplemental Code Channel test modes, 14

Supplemental Channel test modes, and Packet Data Channel test modes. The Reverse 15

Traffic Channel is verified by invoking Fundamental Channel test modes, Dedicated Control 16

Channel test modes, and Supplemental Channel test modes. Table 1.3-1 lists the test 17

modes and the mapping to radio configurations. 18

19

Table 1.3-1. Test Configuration Combinations 20

Test Mode Forward Traffic Channel Radio Configuration

Reverse Traffic Channel Radio Configuration

1 1 1

2 2 2

3 3 3

4 4 3

5 5 4

6 6 5

7 7 5

8 8 6

9 9 6

10a 10 3

Note: Test Mode 10b will be defined in the next revision of this Standard.

21

Fundamental Channel Test Mode 1 is entered by setting up a call using the Loopback 22

Service Option (Service Option 2 or 55) or the Markov Service Option (Service Option 54). 23

3GPP2 C.S0011-C v2.0

1-17

Fundamental Channel Test Mode 2 is entered by setting up a call using the Loopback 1

Service Option (Service Option 9 or 55) or the Markov Service Option (Service Option 54). 2

Fundamental Channel Test Modes 3 through 9 are entered by setting up a call using the 3

Loopback Service Option (Service Option 55), Markov Service Option (Service Option 54), or 4

Test Data Service Option (Service Option 32). 5

Dedicated Control Channel Test Modes 3 through 9, Supplemental Channel Test Modes 3 6

through 9, and Packet Data Channel Test Mode 10a are entered by setting up a call using 7

the Test Data Service Option (Service Option 32). 8

Supplemental Code Channel Test Mode 1 is entered by setting up a call using the 9

Loopback Service Option (Service Option 30). 10

Supplemental Code Channel Test Mode 2 is entered by setting up a call using the 11

Loopback Service Option (Service Option 31). 12

The mobile station shall support the Loopback Service Option if the mobile station 13

supports a Forward Fundamental Channel, Reverse Fundamental Channel or Forward 14

Supplemental Code Channel. The mobile station shall support the Test Data Service Option 15

if it supports a Forward Dedicated Control Channel, Reverse Dedicated Control Channel, 16

Forward Supplemental Channel, Reverse Supplemental Channel, or Forward Packet Data 17

Channel. The mobile station may support the Markov Service Option if the mobile station 18

supports a Forward Fundamental Channel or a Reverse Fundamental Channel. 19

1.4 CDMA Equations 20

The equations listed below describe the relationship between various test parameters under 21

different conditions. If the Paging Channel is not supported, the Forward Common Control 22

Channel may be substituted. 23

1.4.1 Transmit Power of the Base Station 24

orc

IEPilot +

or

cI

E Pilot TD +

orc

IE Sync +

or

cI

E QPCH +

orc

IEPaging

+ 25

or

cI

E FCCCH +

or

cI

E BCCH +

or

cI

E CACH +

or

cI

E CPCCH +

or

cI

E FCH + 26

or

cI

E DCCH +

orc

IE ControlPower +

or

cI

E SCCH +

or

cI

E SCH +

orc

IE PDCCH

+ 27

orc

IE PDCH

+ or

cI

E OCNS = 1 28

In the tests defined in this document, the following values are usually used: 29

orc

IEPilot = -7 dB 30

orc

IE Sync = -16 dB 31

3GPP2 C.S0011-C v2.0

1-18

orc

IEPaging

= -12 dB or or

cI

E FCCCH = -12 dB 1

Therefore, if or

cI

E Traffic = -16 dB at 9600 bps data rate, then 2

or

cI

E ControlPower = -26.41 dB 3

orc

IE OCNS = -1.64 dB 4

Otherwise, if or

cI

E Traffic = -16 dB at 1200 bps data rate, then 5

orc

IE ControlPower = -17.38 dB 6

orc

IE OCNS = -1.75 dB 7

1.4.2 Received Signal Strength for Mobile Station Not in Handoff 8

For the purpose of calculating the constant expression ocor

II

or its inverse, orI is the long 9

term average over the test interval. For the purpose of calculating the various channel or

cIE

10

ratios, orI is the long term average over the test interval. 11

0

cI

E Pilot =

1II

IE Pilot

or

ocor

c

+ 12

1.4.2.1 Single-Path Case 13

t

bN

E Sync =

or

ocor

c

II

Bit_Chip_SyncI

E Sync×

14

3GPP2 C.S0011-C v2.0

1-19

t

bN

E QPCH =

or

ocor

c

II

Bit_Chip_QPCHI

E QPCH×

1

t

bN

EPaging =

or

ocor

c

II

Bit_Chip_PagingI

EPaging ×

2

t

bN

E BCCH =

or

ocor

c

II

Bit_Chip_BCCHI

E BCCH×

3

t

bN

E FCCCH =

or

ocor

c

II

Bit_Chip_FCCCHI

E FCCCH×

4

t

bN

E FCH =

or

ocor

c

II

Bit_Chip_FCHI

E FCH×

5

t

bN

E DCCH =

or

ocor

c

II

Bit_Chip_DCCHI

E DCCH×

6

t

bN

E SCCH =

or

ocor

c

II

Bit_Chip_SCCHI

E SCCH×

7

t

bN

E SCH =

or

ocor

c

II

Bit_Chip_SCHI

E SCH×

8

3GPP2 C.S0011-C v2.0

1-20

tb

NE PDCCH

=

or

ocor

c

II

Bit_Chip_PDCCHI

E PDCCH×

1

tb

NE PDCH

=

or

ocor

c

II

Bit_Chip_PDCHI

E PDCH×

2

1.4.2.2 Two-Path Case 3

According to Channel Simulator Configuration 1, 2 and 5 (see 6.4.1.3), these two paths 4

have the same average power. 5

t

bN

E BCCH =

or

cI

E BCCH × BCCH_Chip_Bit ×

21

II

1

or

oc + 6

t

bN

E FCH =

or

cI

E FCH × FCH_Chip_Bit ×

21

II

1

or

oc + 7

t

bN

E DCCH =

or

cI

E DCCH × DCCH_Chip_Bit ×

21

II

1

or

oc + 8

t

bN

E SCH =

or

cI

E SCH × SCH_Chip_Bit ×

21

II

1

or

oc + 9

tb

NE PDCCH

= or

cI

E PDCCH × PDCCH_Chip_Bit ×

21

II

1

or

oc + 10

tb

NE PDCH

= or

cI

E PDCH × PDCH_Chip_Bit ×

21

II

1

or

oc + 11

3GPP2 C.S0011-C v2.0

1-21

1.4.2.3 Three-Path Case 1

According to Channel Simulator Configuration 4 (see 6.4.1.3), the first two paths have the 2

same average power and the third path has half the average power of the first one. 3

t

bN

E BCCH =

orc

IE BCCH

× BCCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 4

t

bN

E FCH =

or

cI

E FCH × FCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 5

DCCH tb

NE

= or

cI

E DCCH × DCCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 6

t

bN

E SCH =

or

cI

E SCH × SCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 7

tb

NE PDCCH

= or

cI

E PDCCH × PDCCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 8

tb

NE PDCH

= or

cI

E PDCH × PDCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 9

1.4.3 Received Signal Strength for Mobile Station in Two-Way Handoff 10

According to Channel Simulator Configuration 2 (see 6.4.1.3), which is used in the tests of 11

the Forward Traffic Channel in two-way handoff, there are two paths from each cell and the 12

power received from each cell is Îor. 13

3GPP2 C.S0011-C v2.0

1-22

For the purpose of calculating the constant expression ocor

II

or its inverse, orI is the long 1

term average over the test interval. For the purpose of calculating the various channel or

cIE

2

ratios, orI is the long term average over the test interval. 3

0

cI

E Pilot(for each pilot) =

2II

IEPilot

or

ocor

c

+ 4

t

bN

E FCH =

or

cI

E FCH × FCH_Chip_Bit ×

23

II

23

or

oc + 5

Generally, if the power received from cell 1 and cell 2 are Îor1 and Îor2, respectively, then 6

0

cI

E Pilot1 =

1II

II

IEPilot

1or2or

1oroc

1or

c

++ 7

0

cI

E Pilot2 =

1II

II

IEPilot

2or1or

2oroc

2or

c

++ 8

1.5 Tolerances 9

1.5.1 CDMA System Parameter Tolerances 10

CDMA parameters are specified in [4]. All parameters indicated in Sections 3 and 4 are 11

exact unless an explicit tolerance is stated. 12

1.5.2 Measurement Tolerances 13

Unless otherwise specified, a measurement tolerance, including the tolerance of the 14

measurement equipment, of ±10% is assumed. 15

Unless otherwise specified, the Îor /Ioc value shall be within ±0.1 dB of the value specified, 16

and the Ioc value shall be within ±5 dB of the value specified. 17

1.6 Test Requirements for Mobile Stations Supporting Analog Operation 18

Mobile stations supporting analog operation in the 800 MHz band shall conform to all 19

requirements in [3], with the exception of the test variations included in this section. 20

3GPP2 C.S0011-C v2.0

1-23

1.6.1 Modulated Tone Frequency 1

[3] states that a modulated tone frequency of 1000 Hz should be used in many tests. A 2

1004 Hz modulated tone frequency may be used in lieu of 1000 Hz. 3

4

3GPP2 C.S0011-C v2.0

1-24

No text1

3GPP2 C.S0011-C v2.0

2-1

2 STANDARD RADIATED EMISSIONS MEASUREMENT PROCEDURE 1

The measurement and calibration procedures described are intended to provide an 2

overview of radiated and conducted signal measurements. A detailed description of the 3

required measurement procedures is given in [1]. 4

2.1 Standard Radiation Test Site 5

The test site shall be on level ground that is of uniform electrical characteristics. The site 6

shall be clear of overhead wires and other metallic objects and shall be as free as possible 7

from undesired signals, such as ignition noise and other carriers. Reflecting objects, such 8

as rain gutters and power cables shall lie outside an ellipse measuring 60 meters on the 9

major axis by 52 meters on the minor axis for a 30-meter site, or an ellipse measuring 6 10

meters on the major axis by 5.2 meters on the minor axis for a 3-meter site. The equipment 11

under test shall be located at one focus of the ellipse and the measuring antenna at the 12

other focus. If desired, shelters may be provided at the test site to protect the equipment 13

and personnel. All such construction shall be of wood, plastic, or other non-metallic 14

material. All power, telephone, and control circuits to the site shall be buried at least 0.3 15

meter under ground. 16

A turntable, essentially flush with the ground, shall be provided that can be remotely 17

controlled. A platform 1.2 meters high shall be provided on this turntable to hold the 18

equipment under test. Any power and control cables that are used for this equipment 19

should extend down to the turntable, and any excess cabling should be coiled on the 20

turntable. 21

If the equipment to be tested is mounted in racks and is not easily removed for testing on 22

the above platform, then the manufacturer may elect to test the equipment when it is 23

mounted in its rack (or racks). In this case, the rack (or racks) may be placed directly on 24

the turntable. 25

If a transmitter with an external antenna connection is being tested, then the RF output of 26

this transmitter shall be terminated in a non-radiating load that is placed on the turntable. 27

A non-radiating load is used in lieu of an antenna to avoid interference with other radio 28

users. The RF cable to this load should be of minimum length. The transmitter shall be 29

tuned and adjusted to its rated output value before starting the tests. 30

In order to conduct unintentional radiator tests as specified in Part 15, subpart B of [2], the 31

radiation site must comply with Sections 5.4.6 through 5.5 of [1] as required by Part 2.948 32

of [2]. 33

2.2 Search Antenna 34

For narrow-band dipole adjustable search antennas, the dipole length shall be adjusted for 35

each measurement frequency. This length may be determined from a calibration ruler that 36

is normally supplied with the equipment. 37

The search antenna shall be mounted on a movable non-metallic horizontal boom that can 38

be raised or lowered on a wooden or other non-metallic pole. The cable connected to the 39

search antenna shall be at a right angle to the antenna. The cable shall be dressed at least 40

3GPP2 C.S0011-C v2.0

2-2

3 meters, either through or along the horizontal boom, in a direction away from the 1

equipment being measured. The search antenna cable may then be dropped from the end 2

of the horizontal boom to ground level for connection to the field-strength measuring 3

equipment. 4

The search antenna shall be capable of being rotated 90 degrees on the end of the 5

horizontal boom to allow measurement of both vertically and horizontally polarized signals. 6

When the antenna length of a vertically mounted antenna does not permit the horizontal 7

boom to be lowered to its minimum specified search range, adjust the minimum height of 8

the boom for 0.3 meter clearance between the end of the antenna and the ground. 9

2.3 Field-Strength Measurement 10

A field-strength meter shall be connected to a search antenna. The field-strength meter 11

shall have sufficient sensitivity and selectivity to measure signals over the required 12

frequency ranges at levels at least 10 dB below the levels specified in any document, 13

standard, or specification that references this measurement procedure. The calibration of 14

the measurement instruments (field-strength meter, antennas, etc.) shall be checked 15

frequently to ensure that their accuracy is in accordance with the current standards. Such 16

calibration checks shall be performed at least once per year. 17

2.4 Frequency Range of Measurements 18

When measuring radiated signals from transmitting equipment, the measurements shall be 19

made from the lowest radio frequency (but no lower than 25 MHz) generated in the 20

equipment to the tenth harmonic of the carrier, except for that region close to the carrier 21

equal to ±250% of the authorized bandwidth. 22

When measuring radiated signals from receiving equipment, the measurements shall be 23

made from 25 MHz to at least 6 GHz. 24

2.5 Test Ranges 25

2.5.1 30-Meter Test Range 26

Measurement of radiated signals shall be made at a point 30 meters from the center of the 27

turntable. The search antenna shall be raised and lowered from 1 to 4 meters in both 28

horizontally and vertically polarized orientations. 29

The field-strength measuring meter may be placed on a suitable table or tripod at the foot 30

of the mast. 31

When measuring radiated emissions from receivers, equipment that contains its own 32

receive antenna shall be tested with the antenna in place. Equipment that is connected to 33

an external receive antenna via a cable shall be tested without the antenna, and the receive 34

ports on the equipment under test shall be terminated in a 50Ω non-radiating resistive 35

load. 36

3GPP2 C.S0011-C v2.0

2-3

2.5.2 3-Meter Test Range 1

Measurement of radiated signals may be made at a point 3 meters from the center of the 2

turntable, provided the following three conditions can be met: 3

1. A ground screen that covers an elliptical area at least 6 meters on the major axis 4

by 5.2 meters on the minor axis is used with the measuring antenna and turntable 5

mounted 3 meters apart. The measuring antenna and turntable shall lie on the 6

major axis and shall be equidistant from the minor axis of the elliptical area. 7

2. The maximum dimension of the equipment shall be 3 meters or less. When 8

measuring radiated signals from receivers, the maximum dimension shall include 9

the antenna if it is an integral part of the device. 10

3. The field-strength measuring equipment is either mounted below the ground level 11

at the test site or is located a sufficient distance away from the equipment being 12

tested and from the search antenna to prevent corruption of the measured data. 13

The search antenna shall be raised and lowered over a range from 1 to 4 meters in both 14

horizontally and vertically polarized orientations. When the search antenna is vertically 15

oriented, the minimum height of the center of the search antenna shall be defined by the 16

length of the lower half of the search antenna. 17

When measuring radiated emissions from receivers, equipment that contains its own 18

receive antenna shall be tested with the antenna in place. Equipment that is connected to 19

an external receive antenna via a cable shall be tested without the antenna, and the receive 20

ports on the equipment under test shall be terminated in a 50Ω non-radiating resistive 21

load. The 3-meter test range may be used for determining compliance with limits specified 22

at 30 meters (or other distances), provided that: 23

1. The ground reflection variations between the two distances have been calibrated for 24

the frequencies of interest at the test range, or 25

2. A 5 dB correction factor is added to the specified radiation limit(s) to allow for 26

average ground reflections. 27

Radiated field strength (volts/meter) varies inversely with distance, so that a measurement 28

made on the 3-meter test range divided by 10 gives the equivalent value that would be 29

measured on a 30-meter test range for the same EIRP (effective isotropic radiated power). 30

The 30-meter field strength in volts/meter can be calculated from the EIRP by using the 31

following formula: 32

µV/m @ 30 meters = 5773.5 × 10EIRP(dBm)/20 33

2.6 Radiated Signal Measurement Procedures 34

Radiated signals having significant levels shall be measured on the 30-meter or the 3-meter 35

range by using the following procedure: 36

1. For each observed radiated signal, raise and lower the search antenna to obtain a 37

maximum reading on the field-strength meter with the antenna horizontally 38

polarized. Then rotate the turntable to maximize the reading. Repeat this 39

3GPP2 C.S0011-C v2.0

2-4

procedure of raising and lowering the antenna and rotating the turntable until the 1

highest possible signal has been obtained. Record this maximum reading. 2

2. Repeat step 1 for each observed radiated signal with the antenna vertically 3

polarized. 4

3. Remove the equipment being tested and replace it with a half-wave antenna. The 5

center of the half-wave antenna should be at the same approximate location as the 6

center of the equipment being tested. 7

4. Feed the half-wave antenna replacing the equipment under test with a signal 8

generator connected to the antenna by means of a non-radiating cable. With the 9

antennas at both ends horizontally polarized and with the signal generator tuned 10

to the observed radiated signal, raise and lower the search antenna to obtain a 11

maximum reading on the field-strength measuring meter. Adjust the level of the 12

signal generator output until the previously recorded maximum reading for this set 13

of conditions is obtained. Record the signal generator power output. 14

5. Repeat step 4 above with both antennas vertically polarized. 15

6. Calculate the power into a reference ideal isotropic antenna by: 16

a. First reducing the readings obtained in steps 4 and 5 above by the power loss 17

in the cable between the generator and the source antenna, and 18

b. Then correcting for the gain of the source antenna used relative to an ideal 19

isotropic antenna. The reading thus obtained is the equivalent effective 20

isotropic radiated power (EIRP) level for the spurious signal being measured. 21

7. Repeat steps 1 through 6 above for all observed signals from the equipment being 22

tested. 23

24

3GPP2 C.S0011-C v2.0

3-1

3 CDMA RECEIVER MINIMUM STANDARDS 1

3.1 Frequency Coverage Requirements 2

The RF channel numbers and frequencies are given for base stations and mobile stations in 3

[11]. The mobile station receive CDMA frequency assignments are associated on a one-to-4

one basis with the transmit CDMA frequency assignments. Each CDMA frequency 5

assignment shall be centered at one of the indicated frequencies. 6

3.2 Acquisition Requirements 7

3.2.1 Idle Handoff Tests 8

3.2.1.1 Idle Handoff in Non-Slotted Mode on the Paging Channel 9

These tests shall be performed for mobile stations that can operate in non-slotted mode 10

while in the Mobile Station Idle State. 11

3.2.1.1.1 Definition 12

When in the Mobile Station Idle State, the mobile station continually searches for the 13

strongest Pilot Channel signal on the current CDMA frequency assignment. The mobile 14

station determines that an idle handoff should occur when it detects a Pilot Channel signal 15

sufficiently stronger than the one it is currently monitoring. 16

Test 1 verifies that the mobile station does not perform alternating idle handoffs between 17

two Pilot Channels so frequently that the mobile station cannot receive paging messages on 18

either of the Forward CDMA Channels by checking the number of idle handoffs performed 19

and the Paging Channel message error rate (MER). 20

Test 2 verifies that the mobile station performs an idle handoff whenever the Ec/I0 of a 21

pilot in the Neighbor Set exceeds the Ec/I0 of the pilot in the Active Set by 3 dB, as 22

measured at the mobile station antenna connector, for a period longer than one second. 23

This is accomplished by checking the number of idle handoffs performed and the Paging 24

Channel MER. 25

3.2.1.1.2 Method of Measurement 26

1. Connect two base stations and an AWGN generator to the mobile station antenna 27

connector as shown in Figure 6.5.1-3. The Forward Channel from base station 1 28

has an arbitrary pilot PN offset index P1, and is called Channel 1. The Forward 29

Channel from base station 2 has an arbitrary pilot PN offset index P2, and is called 30

Channel 2. 31

2. For each band class that the mobile station supports, configure the mobile station 32

to operate in that band class and perform steps 3 through 9. 33

3. Set the Paging Channel data rate of Channel 1 and Channel 2 to 4800 bps. 34

3GPP2 C.S0011-C v2.0

3-2

4. Send the overhead messages consecutively in synchronized message capsules on 1

the Primary Paging Channel of both base stations. Overhead message contents 2

shall be as specified in 6.5.2. 3

5. Set the test parameters for Test 1 as specified in Table 3.2.1.1.2-1. As specified in 4

Figure 3.2.1.1.2-1, the Channel 1 and Channel 2 pilot Ec/I0 levels shall transition 5

every 100 ms. 6

6. Set up a call using Fundamental Channel Test Mode 1 or 3 (see 1.3) and retrieve 7

the parameters PAG_1, PAG_2, PAG_4 and PAG_7, and then end the call. 8

7. Immediately after ending the call, run the test for at least 10 cycles (20 pilot Ec/I0 9

transitions). 10


the parameters PAG_1, PAG_2, PAG_4 and PAG_7, and then end the call. 12


Figure 3.2.1.1.2-2, the Channel 1 pilot Ec/I0 level shall transition between state 1 14

and state 2, where the state 1 duration is 5 seconds and the state 2 duration is 10 15

seconds. Repeat steps 6 through 8. 16

17

Table 3.2.1.1.2-1. Test Parameters for Idle Handoff in Non-Slotted Mode 18

Test 1 Test 2

Parameter Unit Channel 1 Channel 2 Channel 1 Channel 2

Îor /Ioc dB 3 for S1

0 for S2

0 for S1

3 for S2

3 for S1

-16.7 for S2

0 for S1

-4.7 for S2

orc

IEPilot dB -7 -7 -7 -7

orc

IEPaging

dB -12 -12 -12 -12

Ioc dBm/1.23 MHz -55 -55

0c

IEPilot

dB -10 for S1

-13 for S2

-13 for S1

-10 for S2

-10 for S1

-25 for S2 -13

Note: The Pilot Ec/I0 value is calculated from the parameters set in the table. It is not 19

a directly settable parameter. S1 and S2 indicate the two states of the power levels. 20

21

3GPP2 C.S0011-C v2.0

3-3

100 100 Time (ms)

Pilot Ec/I0 = -10 dBChannel 1

Pilot

Channel 2Pilot 3 dB

100 1

Figure 3.2.1.1.2-1. Idle Handoff in Non-Slotted Mode (Test 1) 2

3

10 5 Time (s)


PilotChannel 2

Pilot

3 dB

5

12 dB

4

Figure 3.2.1.1.2-2. Idle Handoff in Non-Slotted Mode (Test 2) 5

6

3.2.1.1.3 Minimum Standard 7

The number of idle handoffs during a test is given by ∆PAG_7, where ∆PAG_7 is the 8

increment of the parameter PAG_7 during the test. 9

The Paging Channel MER is estimated by 10

RATE_MSG4_PAG2_PAG1_PAG1MER

×∆∆−∆

−= 11

where ∆PAG_1, ∆PAG_2, and ∆PAG_4 are the increment of parameters PAG_1, PAG_2 and 12

PAG_4 during the test, respectively, and MSG_RATE is the average number of messages 13

3GPP2 C.S0011-C v2.0

3-4

sent consecutively in a period of 20 half-frames1. MSG_RATE is equal to 5/20 when five 1

overhead messages are sent consecutively in synchronized message capsules2. If the base 2

stations cannot be configured to send this specified average message rate, then MSG_RATE 3

shall be the actual average message rate configured for the tests3. 4

Test 1: The mobile station should not perform any idle handoffs. The Paging Channel MER 5

shall be less than or equal to 0.1. 6

Test 2: The number of idle handoffs shall be equal to the number of pilot Ec/I0 transitions. 7

The Paging Channel MER shall be less than or equal to 0.1. 8

3.2.1.2 Idle Handoff in Slotted Mode on the Paging Channel 9

These tests shall be performed for mobile stations that can operate in slotted mode. 10


When in the Mobile Station Idle State, the mobile station searches for the strongest Pilot 12

Channel signal on the current CDMA frequency assignment during the assigned slots. The 13

mobile station determines that an idle handoff should occur when it detects a Pilot 14

Channel signal sufficiently stronger than the one it is currently monitoring. 15

This test verifies that the mobile station performs an idle handoff whenever the Ec/I0 of a 16


measured at the mobile station antenna connector, by measuring the number of idle 18

handoffs performed in a fixed period of time. 19






Channel 2. 25



3. Set the Paging Channel data rate of Channel 1 and Channel 2 to 4800 bps. 28

4. Set MAX_SLOT_CYCLE_INDEX to 0 in the System Parameters Message (each slot 29

cycle is 1.28 seconds long). 30

1 All empty Paging Channel half-frames shall be filled with zeroes.

2 This requires that the General Page Message (see [6]) and Null Message (see [5]) are not sent.

3 In addition to the five overhead messages, up to one General Page Message (see [6]) and one or more Null Message (see [5]) may be sent.

3GPP2 C.S0011-C v2.0

3-5

5. Send the overhead messages consecutively on the Primary Paging Channel of both 1

Channel 1 and Channel 2. Overhead message contents shall be as specified in 2

6.5.2. 3

6. Send a General Page Message with no page records with the CLASS_0_DONE, 4

CLASS_1_DONE, TMSI_DONE, and BROADCAST_DONE fields set to ‘1’ at the 5

beginning of each assigned Paging Channel slot of the mobile station in every slot 6

cycle on the Primary Paging Channel of both Channel 1 and Channel 2. 7

7. Set the test parameters as specified in Table 3.2.1.2.2-1 and Figure 3.2.1.2.2-1. 8

8. Set up a call using Fundamental Channel Test Mode 1 or 3 (see 1.3), retrieve the 9

parameter PAG_7, and then end the call. 10

9. Run the test for exactly 20 Channel 1 pilot Ec/I0 transitions, starting and ending 11

with the Channel 1 pilot Ec/I0 at -25 dB. Allow three seconds after the last 12

transition before performing step 10. 13



16

Table 3.2.1.2.2-1. Test Parameters for Slotted Mode Idle Handoff 17

Parameter Unit Channel 1 Channel 2


-16.7 for S2

0 for S1

-4.7 for S2

orc

IEPilot dB -7 -7

orc

IEPaging

dB -12 -12

Ioc dBm/1.23 MHz -55

0c

IEPilot

dB -10 for S1

-25 for S2 -13

Note: The Pilot Ec/I0 value is calculated from the parameters 18

in the table. It is not a directly settable parameter. S1 and S2 19

indicate the two states of the power levels. 20

21

3GPP2 C.S0011-C v2.0

3-6

3 9 Time (s)

Pilot Ec/I0 = -13 dBChannel 1Pilot

Channel 2Pilot

3 dB

9

12 dB

1

Figure 3.2.1.2.2-1. Slotted Mode Idle Handoff 2

3




The number of idle handoffs shall be greater than or equal to 18. 7

3.2.1.3 Idle Handoff in Slotted Mode on the Forward Common Control Channel 8

These tests shall be performed for mobile stations that can operate in slotted mode and can 9

monitor the Forward Common Control Channel. 10



Channel signal on the current CDMA frequency assignment during the assigned slots. The 13

mobile station determines that an idle handoff should occur when it detects a Pilot 14

Channel signal sufficiently stronger than the one it is currently monitoring. 15

This test verifies that the mobile station performs an idle handoff whenever the Ec/I0 of a 16


measured at the mobile station antenna connector, by measuring the number of idle 18

handoffs performed in a fixed period of time. 19






Channel 2. 25



3GPP2 C.S0011-C v2.0

3-7

3. Set the Forward Common Control Channel data rate of Channel 1 and Channel 2 1

to 4800 bps. 2


cycle is 1.28 seconds long). 4

5. Send the overhead messages consecutively on the Forward Broadcast Control 5

Channel of both Channel 1 and Channel 2. Overhead message contents shall be as 6

specified in 6.5.2. 7

6. Send a General Page Message with no page records with the CLASS_0_DONE, 8


beginning of each assigned Forward Common Control Channel slot of the mobile 10

station in every slot cycle on the Forward Common Control Channel of both 11

Channel 1 and Channel 2. 12

7. Set the test parameters as specified in Table 3.2.1.3.2-1 and Figure 3.2.1.3.2-1. 13

8. Set up a call using Fundamental Channel Test Mode 3 (see 1.3) if the mobile 14

station supports Radio Configuration 3 or 4, or set up a call using Fundamental 15

Channel Test Mode 7 (see 1.3) if the mobile station supports Radio Configuration 5 16

or 6, retrieve the parameter PAG_7, and then end the call. 17

9. Run the test for exactly 20 Channel 1 pilot Ec/I0 transitions, starting and ending 18

with the Channel 1 pilot Ec/I0 at -25 dB. Allow three seconds after the last 19

transition before performing continuing with step 10. 20

10. Set up a call using Fundamental Channel Test Mode 3 (see 1.3) if the mobile 21

station supports Radio Configuration 3 or 4, or set up a call using Fundamental 22

Channel Test Mode 7 (see 1.3) if the mobile station supports Radio Configuration 5 23

or 6, retrieve the parameter PAG_7, and then end the call. 24

11. Set up a Quick Paging Channel associated with the Forward Common Control 25

Channel under test if the mobile station supports the Quick Paging Channel. Set 26

up the Sync Channel Message (or MC-MAP Sync Channel Message if 27

DIF_FREQ_PARAMS = ‘1’) and the MC-RR Parameters Message on the Broadcast 28

Control Channel to inform the mobile station of the existence of the Quick Paging 29

Channel with the Forward Common Control Channel. Repeat steps 4 through 10. 30

31

3GPP2 C.S0011-C v2.0

3-8

Table 3.2.1.3.2-1. Test Parameters for Slotted Mode Idle Handoff 1



-16.7 for S2

0 for S1

-4.7 for S2

orc

IEPilot dB -7 -7

orc

IEPaging

dB -12 -12


0c

IEPilot

dB -10 for S1

-25 for S2 -13




5

3 9 Time (s)

Pilot Ec/I0 = -13 dBChannel 1Pilot

Channel 2Pilot

3 dB

9

12 dB

6

Figure 3.2.1.3.2-1. Slotted Mode Idle Handoff 7

8




The number of idle handoffs shall be greater than or equal to 18. 12

3GPP2 C.S0011-C v2.0

3-9

3.2.1.4 Idle Handoff to Another Frequency 1



Channel signal on the current CDMA frequency assignment. The mobile station determines 4

that an idle handoff should occur when it detects a Pilot Channel signal sufficiently 5

stronger than the one it is currently monitoring. However, there are system configurations 6

in which a neighbor base station cannot use the current CDMA frequency assignment. In 7

this case, the Extended Neighbor List Message or General Neighbor List Message may 8

contain the identity of a neighbor base station on a different CDMA frequency assignment. 9

The mobile station also searches this CDMA frequency assignment for this neighbor base 10

station. 11

The first test verifies that the mobile station quickly performs an idle handoff to a pilot in 12

the Neighbor Set which is on other than the current CDMA frequency assignment whenever 13

the Ec/I0 of all pilots in the Active Set and the Neighbor Set which are on the current 14

CDMA frequency assignment are less than some specified Ec/I0. 15

The second test verifies that the mobile station performs an idle handoff to a pilot in the 16

Neighbor Set which is on other than the current CDMA frequency assignment whenever the 17

Ec/I0 of all pilots in the Active Set and the Neighbor Set, which are on the current CDMA 18

frequency assignment, are less than some specified Ec/I0 and are less than the Ec/I0 of a 19

pilot in the Neighbor Set which is on other than the current CDMA frequency assignment. 20

The following tests are directly applicable to mobile stations that operate in the slotted 21

mode. For mobile stations that do not operate in the slotted mode, the same test 22

procedures apply, but the Audit Order shall be sent in any sequence of slots separated by 23

1.28 seconds. 24






Channel 2. Base station 1 uses arbitrary frequency f1, and base station 2 uses an 30

arbitrary but different frequency, f2. The frequency, f2, shall be a preferred 31

frequency with respect to system determination. 32



3. The number of Paging Channels should be the same for both Channel 1 and 35

Channel 2. Set the Paging Channel data rate of Channel 1 and Channel 2 to 4800 36

bps. 37


cycle is 1.28 seconds long). Set GEN_NGHBR_LIST to 1 in the System Parameters 39

Message. 40

3GPP2 C.S0011-C v2.0

3-10

5. Send the overhead messages consecutively on the Primary Paging Channel of both 1

Channel 1 and Channel 2. Overhead message contents shall be as specified in 2

6.5.2 with the exception of the General Neighbor List Message. For Channel 1, the 3

General Neighbor List Message shall have the following field values: 4

5

Field Value (Decimal)

PILOT_INC 12 (768 chips)

NGHBR_SRCH_MODE 1 (search priorities included)

NGHBR_CONFIG_PN_INCL 1 (PN offsets included)

FREQ_FIELDS_INCL 1 (frequency included)

USE_TIMING 0 (hopping beacon timing off)

NUM_NGHBR 7 (seven neighbors)

NGHBR_CONFIG 0 (same as current)

NGHBR_PN P2

SEARCH_PRIORITY 1 (medium)

FREQ_INCL 1 (frequency included)

NGHBR_BAND x (where x is the band class)

NGHBR_FREQ f2

NGHBR_CONFIG 0

NGHBR_PN P3

SEARCH_PRIORITY 3 (very high)

FREQ_INCL 0 (frequency not included)

NGHBR_CONFIG 0

NGHBR_PN P4



NGHBR_CONFIG 0

NGHBR_PN P5



NGHBR_CONFIG 0

NGHBR_PN P6



NGHBR_CONFIG 0

NGHBR_PN P7

3GPP2 C.S0011-C v2.0

3-11




NGHBR_CONFIG 0

NGHBR_PN P8



1

For Channel 2, the General Neighbor List Message shall have the following field values: 2

3


PILOT_INC 12 (768 chips)

NGHBR_SRCH_MODE 1 (search priorities included)

NGHBR_CONFIG_PN_INCL 1 (PN offsets included)

FREQ_FIELDS_INCL 1 (frequencies included)

USE_TIMING 0 (hopping beacon timing off)

NUM_NGHBR 7 (seven neighbors)

NGHBR_CONFIG 0 (same as current)

NGHBR_PN P1

SEARCH_PRIORITY 1 (medium)

FREQ_INCL 1 (frequency included)

NGHBR_BAND x (where x is the band class)

NGHBR_FREQ f1

NGHBR_CONFIG 0

NGHBR_PN P3


FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P4

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P5

SEARCH_PRIORITY 3

3GPP2 C.S0011-C v2.0

3-12


FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P6

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P7

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P8

SEARCH_PRIORITY 3

FREQ_INCL 0

1

6. Set the Channel 1 parameters to the maximum values for Test 1 in Table 3.2.1.4.2-2

1 (Îor/Ioc is equal to 0 dB). Set the Channel 2 parameters to the minimum values 3

for Test 1 in Table 3.2.1.4.2-1 (Îor/Ioc is equal to -18 dB). 4

7. Set up a call to the mobile station and retrieve the parameters PAG_3 and PAG_7, 5

and then end the call. 6

8. Send a General Page Message with no page records and with the CLASS_0_DONE, 7


beginning of each assigned Paging Channel slot of the mobile station on the 9

Channel 1 Primary Paging Channel. Send an Audit Order addressed to the mobile 10

station as a message requiring acknowledgement followed by a General Page 11

Message with no page records and with the CLASS_0_DONE, CLASS_1_DONE, 12

TMSI_DONE, and BROADCAST_DONE fields set to ‘1’ at the beginning of each 13

assigned Paging Channel slot of the mobile station on the Channel 2 Primary 14

Paging Channel. 15


Figure 3.2.1.4.2-1, the Channel 1 and Channel 2 levels shall transition every 2.56 17

seconds, which corresponds to every second assigned slot of the mobile station. 18

The levels shall transition after sending the General Page Message and before the 19

beginning of the next assigned slot. 20

10. Run the test for at least 10 cycles (20 pilot Ec/I0 transitions), ending with the 21

Channel 1 pilot Ec/I0 at -10 dB. 22



3GPP2 C.S0011-C v2.0

3-13

12. Set the Channel 1 parameters to the maximum values for Test 2 in Table 3.2.1.4.2-1

1 (Îor/Ioc is equal to 0 dB). Set the Channel 2 parameters to the minimum values 2

for Test 2 in Table 3.2.1.4.2-1 (Îor /Ioc is equal to -6 dB). 3


Figure 3.2.1.4.2-2, the Channel 1 and Channel 2 levels shall transition every 10.24 5

seconds, which corresponds to every eighth assigned slot of the mobile station. The 6

levels shall transition after sending the General Page Message and before the 7

beginning of the next assigned slot. 8

14. Run the test for at least 8 cycles (16 pilot Ec/I0 transitions), ending with the 9

Channel 1 pilot Ec/I0 at -10 dB. 10



13

Table 3.2.1.4.2-1. Test Parameters for Idle Handoff to Another Frequency 14

Test 1 Test 2

Parameter Unit Channel 1 Channel 2 Channel 1 Channel 2

Îor/Ioc dB Max = 0

Min = -18

Max = 0

Min = -18

Max = 0

Min = -6

Max = 0

Min = -6

orc

IEPilot dB -7 -7 -7 -7

orc

IEPaging dB -12 -12 -12 -12

Ioc dBm/1.23 MHz -75 -75

0c

IEPilot

dB Max = -10

Min = -25.1

Max = -10

Min = -25.1

Max = -10

Min = -14.0

Max = -10

Min = -14.0

t

bN

EPaging dB Max = 12.1

Min = -5.9

Max = 12.1

Min = -5.9

Max = 12.1

Min = 6.1

Max = 12.1

Min = 6.1

Note: The Pilot Ec/I0 and Paging Eb/Nt values are calculated from the parameters in 15

the table. These are not directly settable parameters. 16

17

3GPP2 C.S0011-C v2.0

3-14

AssignedPaging

Channel Slots

Mobile StationShould Receive AuditOrder Messages in

These Slots

2.56 2.56 Time (s)


Pilot

Channel 2Pilot 15.1 dB

2.56 1

Figure 3.2.1.4.2-1. Idle Handoff to Another Frequency (Test 1) 2

3

AssignedPaging Channel

Slots

Mobile StationShould ReceiveMessages in All

Slots

10.24 10.24 Time (s)


Pilot

Channel 2Pilot 4 dB

10.24 4

Figure 3.2.1.4.2-2. Idle Handoff to Another Frequency (Test 2) 5

6

3GPP2 C.S0011-C v2.0

3-15




The number of Audit Orders that were correctly received on Channel 2 during a test is given 4

by ∆PAG_3, where ∆PAG_3 is the increment of the parameter PAG_3 during the test. 5

Test 1: Since the change in pilot power level occurs when the mobile station is operating in 6

slotted mode, it is possible that the mobile station will miss messages sent in the first slot 7

after the transition. However, the mobile station shall receive messages in the second slot 8

after the transition. 9

The number of idle handoffs shall be equal to the number of pilot Ec/I0 transitions. 10

The number of Audit Orders that were correctly received shall be at least one half the 11

number of pilot Ec/I0 transitions. If the transition occurs sufficiently before the first slot, 12

then the number of Audit Orders that a mobile station not operating in the slotted mode 13

should have correctly received is equal to the number of pilot Ec/I0 transitions. 14

Test 2: Since the levels are sufficient to correctly receive messages on both Channel 1 and 15

Channel 2, the mobile station shall receive messages in all assigned slots. The mobile 16

station shall perform idle handoffs to the frequency with the stronger pilot. 17

The number of idle handoffs shall be equal to the number of pilot Ec/I0 transitions. 18

The number of Audit Orders that were correctly received shall be equal to four times the 19

number of pilot Ec/I0 transitions. 20

3.2.2 Soft Handoff Tests 21

3.2.2.1 Neighbor Set Pilot Detection and Incorrect Detection in Soft Handoff 22


This test measures the detection time for a pilot in the Neighbor Set at three values of pilot 24

Ec/I0, for the static add threshold test configuration. The detection time of a pilot is defined 25

as the time elapsed from the time when the pilot increases to a given Ec/I0 until the mobile 26

station sends a Pilot Strength Measurement Message or Extended Pilot Strength Measurement 27

Message containing this pilot. The accuracy of the Candidate Set pilot PN phase reported in 28

the corresponding Pilot Strength Measurement Message or Extended Pilot Strength 29

Measurement Message is also examined. 30

The correct detection of a pilot in the Neighbor Set is defined as the acquisition of a pilot 31

with Ec/I0 above the value defined by T_ADD. The value of T_ADD is set to 28 (-14 dB) as 32

specified in 6.5.2. An incorrect detection of a pilot in the Neighbor Set is defined as the 33

acquisition of a pilot with Ec/I0 below the value defined by T_ADD. 34





3GPP2 C.S0011-C v2.0

3-16


Channel 2. 2



3. Set up a call using Fundamental Channel Test Mode 1 or 3 or Dedicated Control 5

Channel Test Mode 3 (see 1.3) with 9600 bps data rate only and perform steps 4 6

through 10. 7

4. Set the value of T_TDROP in the System Parameters Message to 1 (1 second). 8

5. Set the base station so as to not send any Extended Handoff Direction Message or 9

General Handoff Direction Message as a response to the Pilot Strength Measurement 10

Message or Extended Pilot Strength Measurement Message sent by the mobile 11

station. 12

6. Set the test parameters for Test 1 as specified in Table 3.2.2.1.2-1 and change the 13

pilot strength of Channel 2 as specified in Figure 3.2.2.1.2-1 with T equal to 0.8 14

seconds. 15

7. Send the Pilot Measurement Request Order as specified in Figure 3.2.2.1.2-1. 16

8. Record the transmission time and contents of each Pilot Strength Measurement 17


station. 19


pilot strength of Channel 2 as specified in Figure 3.2.2.1.2-1 with T equal to 0.85 21

seconds. Repeat steps 7 and 8. 22


pilot strength of Channel 2 as specified in Figure 3.2.2.1.2-2 with T equal to 15 24

seconds. Repeat steps 7 and 8 for 20 cycles of Channel 2 Pilot Ec/I0. 25

26

3GPP2 C.S0011-C v2.0

3-17

Table 3.2.2.1.2-1. Test Parameters for Neighbor Set Pilot Detection (Test 1) 1


Îor/Ioc dB 1.4 for S1

-1.8 for S2

0.4 for S1

−∞ for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -11 -12 for S1

−∞ for S2

Note: The Pilot Ec/I0 value is calculated from the parameters in the 2

table. It is not a directly settable parameter. S1 and S2 indicate the two 3

states of the power levels. 4

5

Table 3.2.2.1.2-2. Test Parameters for Neighbor Set Pilot Detection (Test 2) 6


Îor/Ioc dB 0.22 for S1

-1.8 for S2

-2.3 for S1

−∞ for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -11 -13.5 for S1

−∞ for S2




10

3GPP2 C.S0011-C v2.0

3-18

Table 3.2.2.1.2-3. Test Parameters for Neighbor Set Pilot Incorrect Detection 1

(Test 3) 2


Îor/Ioc dB -0.9 for S1

-1.8 for S2

-6.4 for S1

−∞ for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -11 -16.5 for S1

−∞ for S2




6

4 1 T

Pilot Ec/Io

Channel 1 Pilot

T_ADD

Time (s)

T_DROP

Channel 2 Pilot

Pilot MeasurementRequest Order

7

Figure 3.2.2.1.2-1. Neighbor Set Pilot Detection 8

9

3GPP2 C.S0011-C v2.0

3-19

4 1 T

Pilot Ec/Io

Channel 1 Pilot

T_ADD

Time (s)

T_DROP

Channel 2 Pilot

Pilot MeasurementRequest Order

1

Figure 3.2.2.1.2-2. Neighbor Set Pilot Incorrect Detection 2

3


Pilots other than P1 or P2 shall not be reported in any Pilot Strength Measurement Message 5

or Extended Pilot Strength Measurement Message. 6

Test 1: 7

1. The rate of valid detection within 0.8 seconds shall be greater than 90% with 95% 8

confidence (see 6.6). 9

2. All of the transmissions of Pilot Strength Measurement Message or Extended Pilot 10

Strength Measurement Message sent as a response to the Pilot Measurement 11

Request Order shall only contain P1. 12

3. The reported pilot PN phase for P2 in the Pilot Strength Measurement Message or 13

Extended Pilot Strength Measurement Message in which it is contained shall be no 14

greater than ±1 chip from the actual offset. 15

Test 2: 16

The rate of valid detection within 0.85 seconds shall be greater than 50% with 95% 17


Test 3: 19

There shall be no more than one Pilot Strength Measurement Message or Extended Pilot 20

Strength Measurement Message containing P2 during the test. 21

3GPP2 C.S0011-C v2.0

3-20

3.2.2.2 Candidate Set Pilot Detection and Incorrect Detection in Soft Handoff 1


This test measures the detection time for a pilot in the Candidate Set for the static 3

comparison threshold test configuration. The detection time of a pilot is defined as the time 4

elapsed from the time when the pilot increases to a given Ec/I0 until the mobile station 5

sends a Pilot Strength Measurement Message or Extended Pilot Strength Measurement 6

Message containing this pilot. The accuracy of the Active Set pilot PN phase reported in the 7

corresponding Pilot Strength Measurement Message or Extended Pilot Strength Measurement 8

Message is also examined. 9

The correct detection of a pilot in the Candidate Set is defined as the detection of a pilot in 10

the Candidate Set with Ec/I0 at least 0.5 x T_COMP dB above the Ec/I0 of an Active Set 11

pilot. The value of T_COMP is set to 5 (i.e. 0.5 x T_COMP = 2.5 dB) as specified in 6.5.2. An 12

incorrect detection of a pilot in the Candidate Set is defined as the detection of a pilot with 13

Ec/I0 less than 0.5 x T_COMP dB above the Ec/I0 of any Active Set pilot. 14






Channel 2. 20





through 8. 25




station. 29


pilot strength of Channel 2 as specified in Figure 3.2.2.2.2-1. 31

6. Send the Universal Handoff Direction Message listing only pilot P1 as specified in 32

Figure 3.2.2.2.2-1. 33



station. 36


pilot strength of Channel 2 as specified in Figure 3.2.2.2.2-2. 38

9. Set up a call using the current test mode. 39

3GPP2 C.S0011-C v2.0

3-21

10. Send the Universal Handoff Direction Message listing only pilot P1 as specified in 1

Figure 3.2.2.2.2-2. 2



station. 5

6

Table 3.2.2.2.2-1. Test Parameters for Candidate Set Pilot Detection (Test 1) 7



-4.8 for S2

-0.1 for S1

-4.8 for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -14 -11 for S1

-14 for S2




11

Table 3.2.2.2.2-2. Test Parameters for Candidate Set Pilot Incorrect Detection 12

(Test 2) 13



-3.0 for S2

-0.5 for S1

-3.0 for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -13 -11.5 for S1

-13 for S2




3GPP2 C.S0011-C v2.0

3-22

1

4 1 2.5

Pilot Ec/Io

Pilot ComparisonThreshold

Time (s)

Channel 2 Pilot

Universal HandoffDirection Message

Channel 1 Pilot

0.5 × T_COMP dB

2

Figure 3.2.2.2.2-1. Candidate Set Pilot Detection (Test 1) 3

4

4 1 2.5

Pilot Ec/Io

Time (s)

Channel 2 Pilot

Channel 1 Pilot

4 1


0.5 × T_COMP dB

Pilot ComparisonThreshold

5

Figure 3.2.2.2.2-2. Candidate Set Pilot Incorrect Detection (Test 2) 6

7

3GPP2 C.S0011-C v2.0

3-23


Test 1: 2

1. The rate of correct detection within 2.5 seconds shall be greater than 90% with 3

95% confidence (see 6.6). 4




Test 2: The probability that a Pilot Strength Measurement Message or Extended Pilot Strength 8

Measurement Message will be sent containing P2 within 2.5 seconds is 20% or less with 9


3.2.2.3 Active Set Pilot Loss Detection in Soft Handoff 11


This test measures the loss detection time for a diminishing pilot in the Active Set for the 13

static drop threshold test configuration. The loss detection time for a diminishing pilot in 14

the Active Set is defined as the time elapsed from the time when the pilot decreases to a 15

given Ec/I0 until the mobile station sends a Pilot Strength Measurement Message or 16

Extended Pilot Strength Measurement Message which flags this pilot for deletion from the 17

active set. The accuracy of the PN phase and strength of Active Set pilots reported in the 18

Pilot Strength Measurement Message or Extended Pilot Strength Measurement Message is also 19

examined. 20

The mobile station sends a Pilot Strength Measurement Message or Extended Pilot Strength 21

Measurement Message when the pilot Ec/I0 value of a pilot in the Active Set drops below 22

the value defined by T_DROP for a period of time defined by T_TDROP. The value of 23

T_DROP is set to 32 (i.e. 0.5 x T_DROP = -16 dB) as specified in 6.5.2. The value of 24

T_TDROP is set to 3 (4 seconds) for Test 1, and T_TDROP is set to 2 (2 seconds) for Test 2. 25






Channel 2. 31





through 10. 36



3GPP2 C.S0011-C v2.0

3-24


station. 2

5. Send a Universal Handoff Direction Message to the mobile station, specifying the 3

following pilots in the Active Set: 4

5

Parameter Value (Decimal)

PILOT_PN P1

PILOT_PN P2

6

6. Set the test parameters for Test 1 as specified in Table 3.2.2.3.2-1. Set the value of 7

T_TDROP to 3 (4 seconds) as specified in 6.5.2. 8

7. Record Reverse Traffic Channel messages for 5 minutes. 9

8. Set the test parameters for Test 2 as specified in Table 3.2.2.3.2-2 and Figure 10

3.2.2.3.2-1. Set the value of T_TDROP to 2 (2 seconds). 11

9. Send a Universal Handoff Direction Message to the mobile station as specified in 12

Figure 3.2.2.3.2-1, with the following pilots in the Active Set: 13

14


PILOT_PN P1

PILOT_PN P2

15



station. 18

19

3GPP2 C.S0011-C v2.0

3-25

Table 3.2.2.3.2-1. Test Parameters for Active Set Pilot Incorrect Loss Detection (Test 1

1) 2


Îor/Ioc dB -0.5 -4.5

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 -7


0c

IEPilot

dB -11 -15


table. It is not a directly settable parameter. 4

5

Table 3.2.2.3.2-2. Test Parameters for Active Set Pilot Loss Detection (Test 2) 6



2.9 for S2

-7.0 for S1

2.9 for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 -7


0c

IEPilot

dB -11 -17 for S1

-11 for S2




10

3GPP2 C.S0011-C v2.0

3-26

6 2

Pilot Ec/Io

Time (s)

Channel 1 Pilot


1

T_DROP

T_ADD

Channel 2 Pilot

1

Figure 3.2.2.3.2-1. Active Set Pilot Loss Detection (Test 2) 2

3


Test 1: 5

The mobile station shall not send any Pilot Strength Measurement Message or 6

Extended Pilot Strength Measurement Message during the test. 7

Test 2: 8

1. The rate of loss detection within 6 seconds shall be greater than 80% with 95% 9





3. The reported pilot Ec/I0 value for P1 and P2 in the Pilot Strength Measurement 14

Message or Extended Pilot Strength Measurement Message shall be no greater than 15

±1.5 dB from their set values. 16

3.2.3 Access and Access Probe Handoff Tests 17

3.2.3.1 Access Probe Handoff 18


The mobile station is permitted to perform an access probe handoff when the mobile 20

station is in the Page Response Substate or the Mobile Station Origination Attempt Substate. 21

3GPP2 C.S0011-C v2.0

3-27

The correct detection of a pilot while in the System Access State is defined as the detection 1

of a pilot in the ACCESS_HO_LIST with Ec/I0 above the value defined by T_ADD. The value 2

of T_ADD is set to 28 (-14 dB) as specified in 6.5.2. An incorrect detection of a pilot while in 3

the System Access State is defined as the detection of a pilot in the ACCESS_HO_LIST with 4

Ec/I0 below the value defined by T_ADD. 5


1. Connect two base stations to the mobile station antenna connector as shown in 7

Figure 6.5.1-3. The AWGN source is not used in this test. The Forward Channel 8

from base station 1 has an arbitrary pilot PN offset index P1, and is called Channel 9

1. The Forward Channel from base station 2 has an arbitrary pilot PN offset index 10

P2, and is called Channel 2. 11



3. Set the Paging Channel data rate of Channel 1 and Channel 2 to 4800 bps for Test 14

1. 15

4. Ensure that P2 is the first pilot listed in the Neighbor List Message, Extended 16

Neighbor List Message, General Neighbor List Message or Universal Neighbor List 17

Message sent on Channel 1. 18

5. Set the following parameters in the Extended System Parameters Message: 19

20

Parameters Value (Binary)

NGHBR_SET_ENTRY_INFO 0 (Access entry handoff is disabled)

NGHBR_SET_ACCESS_INFO 1 (Base station is including info on neighbor set access probe

handoff or access handoff)

ACCESS_HO 0 (Disabled)

ACCESS_PROBE_HO 1 (Enabled)

ACC_HO_LIST_UPD 0 (No access probe handoffs are allowed to pilots not listed in

ACCESS_HO_LIST)

MAX_NUM_PROBE_HO 0 (Only one access probe handoff during this access attempt test is

allowed)

NGHBR_SET_SIZE 1 (P2 is the first and only pilot to be listed)

ACCESS_HO_ALLOWED 1 (An access probe handoff to P2 is allowed)

21

3GPP2 C.S0011-C v2.0

3-28

6. Set the test parameters as specified in Table 3.2.3.1.2-1. 1

2

Table 3.2.3.1.2-1. Test Parameters for Access Probe Handoff 3


Îor dBm/1.23 MHz -55 -58 for S1

-45 for S2

orc

IEPilot dB -7 -7

orc

IEPaging

or

or

cI

E FCCCH

dB -12 -12

0c

IEPilot

dB -8.8 for S1 -17.4 for S2

-11.8 for S1 -7.4 for S2




7

7. Set base station 1 to ignore all access attempts. 8

8. Page the mobile station from base station 1 as specified in Figure 3.2.3.1.2-1. 9

9. After power is detected in an access probe from the mobile station as specified in 10

Figure 3.2.3.1.2-1, adjust the power of channel 2 to –45 dBm/1.23 MHz, the state 11

2 value specified in Table 3.2.3.1.2-1. 12

10. Monitor mobile station transmissions for at least 4 seconds after the adjustment of 13

Channel 2 power to state 2. Perform at least 11 trials. 14

11. If the mobile station supports the Forward Common Control Channel, set the 15

Forward Common Control Channel data rate of Channel 1 and Channel 2 to 9600 16

bps with 20 ms frame length for Test 2. Repeat steps 4 through 10. 17

18

3GPP2 C.S0011-C v2.0

3-29

1

Figure 3.2.3.1.2-1. Access Probe Handoff 2

3


For both Test 1 and Test 2: 5

1. The reported pilot PN phase for P2 in the Page Response Message sent prior to the 6

access probe handoff shall be no greater than ±1 chip from the actual offset for all 7

trials. If the mobile station supports access probe handoff, the reported pilot PN 8

phase for P1 in the Page Response Message sent after the access probe handoff 9

shall also be no greater than ±1 chip from the actual offset for all trials. 10

2. Valid detection of P2 prior to the access probe handoff shall occur in 90% of the 11

trials with 95% confidence (see 6.6). 12

3. If the mobile station supports access probe handoff, the probability that the mobile 13

station sends an access probe to base station 2 no later than 4 seconds after the 14

transition from state 1 to state 2 shall occur in 90% of the trials with 95% 15

confidence (see 6.6). The mobile station shall send all access probes to base station 16

2 using the appropriate coding for base station 2. 17

Pilot Ec/Io

Time (s)

General PageMessage

Channel 1Pilot

Channel 2Pilot

Page ResponseMessage to Base

Station 1

4


Station 2

Base Station 1detects

access probe

3GPP2 C.S0011-C v2.0

3-30

3.2.3.2 Access Handoff 1


The mobile station is permitted to perform an access handoff to receive the Paging Channel 3

or Forward Common Control Channel with the best pilot strength and an associated Access 4

Channel or Enhanced Access Channel, respectively. The mobile station is permitted to 5

perform an access handoff when waiting for a response from the base station or before 6

sending a response to the base station. An access handoff is permitted after an access 7

attempt while the mobile station is in the Page Response Substate or the Mobile Station 8

Origination Attempt Substate. 9

The value of T_ADD is set to 28 (-14 dB) as specified in 6.5.2. 10



Figure 6.5.1-3. The AWGN source is not used in this test. The Forward Channel 13

from base station 1 has an arbitrary pilot PN offset index P1, and is called Channel 14

1. The Forward Channel from base station 2 has an arbitrary pilot PN offset index 15




3. Set the Paging Channel data rate of Channel 1 and Channel 2 to 4800 bps for Test 19

1. 20

4. Ensure that P2 is the first pilot listed in the Neighbor List Message, Extended 21

Neighbor List Message, General Neighbor List Message, or Universal Neighbor List 22

Message sent on Channel 1. 23

5. Set the following parameters in the Extended System Parameters Message: 24

25

3GPP2 C.S0011-C v2.0

3-31

Parameters Value (Binary)

NGHBR_SET_ENTRY_INFO 0 (Access entry handoff is disabled)

NGHBR_SET_ACCESS_INFO 1 (Base station is including information on neighbor set

access probe handoff or access handoff)

ACCESS_HO 1 (Enabled)

ACCESS_HO_MSG_RSP 1 (Mobile station is permitted to perform an access handoff after receiving a message and before

responding to that message)

ACCESS_PROBE_HO 0 (disabled)

NGHBR_SET_SIZE 1 (P2 is the first and only pilot to be listed)

ACCESS_HO_ALLOWED 1 (An access handoff to P2 is allowed)

1

6. Set the test parameters as specified in Table 3.2.3.2.2-1. 2

3

Table 3.2.3.2.2-1. Test Parameters for Access Handoff 4


Îor dBm/1.23 MHz -55 -58 for S1

-45 for S2

orc

IEPilot dB -7 -7

orc

IEPaging

or

or

cI

E FCCCH

dB -12 -12

0c

IEPilot

dB -8.8 for S1 -17.4 for S2

-11.8 for S1 -7.4 for S2




8

3GPP2 C.S0011-C v2.0

3-32

7. Set base station 1 to acknowledge an access attempt without assigning a channel. 1

8. Page the mobile station from base station 1 as specified in Figure 3.2.3.2.2-1. 2

9. After the Page Response Message is received and an acknowledgement is sent on 3

Channel 1 as specified in Figure 3.2.3.2.2-1, adjust the power of channel 2 to –45 4

dBm/1.23 MHz, the state 2 value specified in Table 3.2.3.2.2-1. 5

10. Set base station 2 to send a single Channel Assignment Message or Extended 6

Channel Assignment Message to the mobile station four seconds after the transition 7

from state 1 to state 2. 8

11. Verify the mobile station completes the call on base station 2 for each trial. Perform 9

at least 11 trials. 10

12. If the mobile station supports the Forward Common Control Channel, set the 11

Forward Common Control Channel data rate of Channel 1 and Channel 2 to 9600 12

bps with 20 ms frame length for Test 2. Repeat steps 4 through 11. 13

14

15

Figure 3.2.3.2.2-1. Access Handoff 16

17


For both Test 1 and Test 2: 19

1. The reported pilot PN phase for P2 in the Page Response Message sent prior to the 20

access handoff shall be no greater than ±1 chip from the actual offset for all trials. 21

Pilot Ec/Io

Time (s)

General PageMessage

Channel 1Pilot

Channel 2Pilot


Station 1

4

Base Station 2 sendssingle Channel

Assignment Message

Base Station 1acknowledgesaccess probe

3GPP2 C.S0011-C v2.0

3-33

2. Valid detection of P2 prior to the access handoff shall occur in 90% of the trials with 1


3. The mobile station shall complete the call on base station 2 in 90% of the trials with 3


3.2.4 Candidate Frequency Single Search 5

3.2.4.1 Definition 6

This test measures the correct detection of a pilot in the Candidate Frequency Neighbor 7

Set. Correct detection is defined as the reporting of a pilot with Ec/I0 above the value 8

defined by CF_T_ADD. The value of CF_T_ADD is set to 28 (-14 dB). An incorrect detection 9

of a pilot in the Candidate Frequency Neighbor Set is defined as the reporting of a pilot with 10

Ec/I0 below the value defined by CF_T_ADD. 11

The base station directs the mobile station to perform a single search of the Candidate 12

Frequency Search Set by sending a Candidate Frequency Search Request Message. The 13

mobile station reports the search results to the base station in the Candidate Frequency 14

Search Report Message. The accuracy of the reported pilot PN phases is also examined. 15

3.2.4.2 Method of Measurement 16


Figure 6.5.1-3. The Forward Channel for base station 1 has a CDMA frequency 18

assignment F1 (any valid value), an arbitrary pilot PN offset index P1, and is called 19

Channel 1. The Forward Channel for base station 2 has a CDMA frequency 20

assignment F2 (any valid value other than F1), an arbitrary pilot PN offset index 21




3. If the mobile station supports demodulation of Radio Configuration 1 or 2, set up a 25

call on Channel 1 using Fundamental Channel Test Mode 1 (see 1.3) with 9600 bps 26

data rate only and perform steps 6 through 9. 27

4. If the mobile station supports demodulation of Radio Configuration 3, 4, or 5, set 28

up a call on Channel 1 using Fundamental Channel Test Mode 3 or Dedicated 29

Control Channel Test Mode 3 (see 1.3) with 9600 bps data rate only and perform 30

steps 6 through 9. 31

5. If the mobile station supports demodulation of Radio Configuration 6, 7, 8, or 9, 32

set up a call on Channel 1 using Fundamental Channel Test Mode 7 or Dedicated 33

Control Channel Test Mode 7 (see 1.3) with 9600 bps data rate only and perform 34

steps 6 through 9. 35

6. Set the test parameters for Test 1 as specified in Table 3.2.4.2-1. 36

7. Send a Candidate Frequency Search Request Message to the mobile station to set 37

an explicit action time with the following parameters: 38

39

3GPP2 C.S0011-C v2.0

3-34

Parameters Value (Decimal)

USE_TIME 1 (use action time)

SEARCH_TYPE 1 (single search)

SEARCH_MODE 0 (CDMA)

CDMA_FREQ F2

SF_TOTAL_EC_THRESH 31 (disabled)

SF_TOTAL_EC_IO_THRESH 31 (disabled)

CF_SRCH_WIN_N 8 (60 chips)

CF_T_ADD 28 (-14 dB)

NUM_PILOTS 1 (1 pilot)

CF_NGHBR_SRCH_MODE 0 (no search priorities or search windows specified)

NGHBR_PN P2

1

8. Record the transmission time and contents of each Candidate Frequency Search 2

Report Message sent by the mobile station. Perform at least 30 trials. 3

9. Set the test parameters for Test 2 as specified in Table 3.2.4.2-2. 4

10. Send a Candidate Frequency Search Request Message to the mobile station as 5

described in step 7. 6

11. Record the transmission time and contents of each Candidate Frequency Search 7

Report Message sent by the mobile station. Perform at least 60 trials. 8

9

Table 3.2.4.2-1. Test Parameters for Candidate Frequency Neighbor Set Pilot 10

Detection (Test 1) 11


Îor/Ioc dB 0 -2.6

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -10 -11.5



3GPP2 C.S0011-C v2.0

3-35

1

Table 3.2.4.2-2. Test Parameters for Candidate Frequency Neighbor Set Pilot 2

Incorrect Detection (Test 2) 3


Îor/Ioc dB 0 -9.5

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -10 -17



6

3.2.4.3 Minimum Standard 7

Test1: 8

1. No pilot other than P2 shall be reported in any Candidate Frequency Search Report 9

Message for all trials. 10

2. Correct detection of P2 shall occur in 90% of the trials with 95% confidence (see 11

6.6). 12

3. The reported pilot PN phase for P2 in the Candidate Frequency Search Report 13

Message shall be no greater than ± 1 chip from the actual offset for all trials. 14

Test 2: 15

Incorrect detection of P2 shall occur in less than 5% of the trials with 95% confidence 16

(see 6.6). 17

3.3 Forward Common Channel Demodulation Performance 18

The mobile station receiver shall be capable of detecting the signal defined in Section 3.1 of 19

[4]. 20

3.3.1 Demodulation of Non-Slotted Mode Paging Channel 21

These tests shall be performed for mobile stations that can operate in non-slotted mode 22

while in the Mobile Station Idle State. 23

3GPP2 C.S0011-C v2.0

3-36


The performance of the demodulation of Paging Channel in an AWGN (no fading or 2

multipath) environment is determined by the message error rate (MER). The MER is 3

measured only for 9600 bps data rate. 4


1. Connect the base station and an AWGN noise source to the mobile station antenna 6

connector as shown in Figure 6.5.1-4. 7



3. Set the Paging Channel data rate to 9600 bps. 10

4. Set the test parameters as specified in Table A.1.1.1-1. 11

5. Send the overhead messages consecutively in synchronized message capsules on 12

the Primary Paging Channel. Overhead message contents shall be as specified in 13

6.5.2. 14


the parameters PAG_1, PAG_2 and PAG_4 and then end the call. 16

7. Run the test for at least 5 seconds and until sufficient confidence is ensured. 17


the parameters PAG_1, PAG_2 and PAG_4. 19


The actual Eb/Nt used in the test shall be within ±0.2 dB of the value indicated in Table 21

A.1.1.2-1. 22

The Paging Channel MER is estimated by 23

RATE_MSG4_PAG2_PAG1_PAG1MER

×∆∆−∆

−= 24

where ∆PAG_1, ∆PAG_2, and ∆PAG_4 are the increment of parameters PAG_1, PAG_2 and 25

PAG_4 during the test, respectively, and MSG_RATE is the average number of messages 26

sent consecutively in a period of 10 half-frames4. MSG_RATE is equal to 5/10 when five 27

overhead messages are sent consecutively in synchronized message capsules5. If the base 28

stations cannot be configured to send this specified average message rate, then MSG_RATE 29

shall be the actual average message rate configured for the tests6. 30

4 All empty Paging Channel half-frames shall be filled with zeroes.

5 This requires that the General Page Message (see [6]) and Null Message (see [5]) are not sent.

6 In addition to the five overhead messages, up to one General Page Message (see [6]) and one or more Null Message (see [5]) may be sent.

3GPP2 C.S0011-C v2.0

3-37

The MER shall not exceed the piece-wise linear MER curve specified by the points in Table 1

A.1.1.2-1 with 95% confidence (see 6.6). 2

3.3.2 Demodulation of Slotted Mode Paging Channel 3

This test shall be performed for mobile stations that can operate in slotted mode. If the 4

mobile station supports the Quick Paging Channel, then this test shall be performed with 5

the Quick Paging Channel enabled. 6


When operating in the slotted mode, the mobile station starts monitoring the Paging 8

Channel at the beginning of the assigned slots. If the mobile station supports the Quick 9

Paging Channel, the mobile station checks its assigned paging indicators in the Quick 10

Paging Channel slot immediately preceding its assigned Paging Channel slot. If the paging 11

indicators are set to “ON”, the mobile station is to receive the Paging Channel in the 12

assigned Paging Channel slot following its assigned Quick Paging Channel slot. 13

These tests verify that the mobile station wakes up in time so that it does not miss the 14

beginning of its assigned slots. If the mobile station supports the Quick Paging Channel, 15

these tests verify that when the mobile station receives its Quick Paging Channel indicators 16

in strong or weak channel test conditions, the mobile station still monitors its assigned 17

Paging Channel slot. 18

This test also examines the demodulation performance of the Paging Channel in an AWGN 19

(no fading or multipath) environment. The demodulation performance of the Paging 20

Channel is determined by the message error rate (MER). The MER is measured only for 21

9600 bps data rate. 22



connector as shown in Figure 6.5.1-4. Set the Paging Channel data rate to 9600 bps. 25

2. For each band class that the mobile station supports, configure the mobile station to 26

operate in that band class and perform steps 3 through 15. 27

3. For each Paging Channel spreading rate that the mobile station supports, perform steps 28

4 through 15. 29

4. Set MAX_SLOT_CYCLE_INDEX to 0 in the ANSI-41 System Parameters Message (each 30

slot cycle is 1.28 seconds long). 31

5. If the mobile station supports the Quick Paging Channel, set the following values in the 32

Extended System Parameters Message: 33

34

3GPP2 C.S0011-C v2.0

3-38


QPCH_SUPPORTED 1 (QPCH enabled)

NUM_QPCH 1 (1 QPCH supported)

QPCH_RATE 0 (4800 bps)

QPCH_POWER_LEVEL_PAGE 2 (3 dB below the Pilot Channel Transmit Power)

1

6. If the mobile station supports the Quick Paging Channel, set both of the mobile 2

station’s paging indicators to “ON” for its assigned Quick Paging Channel slot in 3

every slot cycle. Set all other paging indicator bits to “OFF”, including all reserved 4

indicators. 5

7. Send the overhead messages consecutively on the Primary Paging Channel. 6

Overhead message contents shall be as specified in 6.5.2. 7

8. Send an Audit Order that does not require a layer 2 acknowledgment, addressed to 8

the mobile station, only at the beginning of each assigned Paging Channel slot of 9

the mobile station in every slot cycle. The order shall be part of an Order Message 10

with a length of 82 bits. Within the same slot as the Order Message, send a General 11

Page Message with no page records addressed to the mobile station and with the 12

CLASS_0_DONE, CLASS_1_DONE, TMSI_DONE, and BROADCAST_DONE fields 13

set to ‘1’. 14

9. Set the parameters for Test 1 as specified in Table A.1.2.1-1. 15



11. Run the test for at least two minutes and until sufficient confidence is ensured. 18


parameter PAG_3 and calculate the Paging Channel MER. 20

13. Set the parameters for Test 2 as specified in Table A.1.2.1-2 and repeat steps 10 21

through 12. 22


through 12. 24


through 12. 26


The actual Quick Paging and Paging Eb/Nt values used in the test shall be within ±0.2 dB 28

of the values indicated in Table A.1.2.1-1 through A.1.2.1-4. 29

The Paging Channel MER can be estimated by 30

3GPP2 C.S0011-C v2.0

3-39

PCH MER = 1 - 28.1/T

3_PAG∆ 1

where ∆PAG_3 is the increment of parameter PAG_3 during the test, and T is the length of 2

the test in seconds. 3

Alternatively, the Paging Channel MER can be measured by 4

PCH MER = 1 - N

3_PAG∆ 5

where ∆PAG_3 is the increment of parameter PAG_3 during the test, and N is the exact 6

number of paging channel messages sent by the base station that were addressed to the 7

mobile station under test. 8

If the mobile station supports the Spreading Rate 1 Paging Channel, the Paging Channel 9

MER shall not exceed the piece-wise linear MER curve specified by the points in Table 10

A.1.2.2-1 (for Test 1) and Table A.1.2.2-2 (for Test 2) with 95% confidence (see 6.6). 11

If the mobile station supports the Spreading Rate 3 Paging Channel, the Paging Channel 12

MER shall not exceed the piece-wise linear MER curve specified by the points in Table 13

A.1.2.2-3 (for Test 3) and Table A.1.2.2-4 (for Test 4) with 95% confidence (see 6.6). 14

3.3.3 Demodulation of Broadcast Control Channel in AWGN Channel 15

These tests shall be performed for mobile stations that support the Broadcast Control 16

Channel. 17


This test examines the demodulation performance of the Broadcast Control Channel in an 19

AWGN (no fading or multipath) environment. The demodulation performance of the 20

Broadcast Control Channel is determined by the frame error rate (FER). 21






3. For each Broadcast Control Channel spreading rate and code rate that the mobile 27

station supports, perform steps 4 through 11. 28

4. Send continuous messages on the Broadcast Control Channel in 40ms broadcast 29

slots (19200 bps). Overhead message contents shall be as specified in 6.5.2. 30

5. Set the test parameter values for each test as specified in Table A.1.3.1-1 through 31

A.1.3.1-3. 32

6. Set up a call using Fundamental Channel Test Mode 3 (see 1.3), retrieve the 33

parameters BCCH_6 and BCCH_9, and then end the call. 34

3GPP2 C.S0011-C v2.0

3-40

7. Have the base station increment either the CONFIG_MSG_SEQ or the 1

ACC_MSG_SEQ in the General Page Message sent on the F-CCCH on each paging 2

slot of the MS under test. 3

8. Run the test for at least seven minutes and 41 seconds and until sufficient 4

confidence is ensured. 5



10. Send continuous messages on the Broadcast Control Channel (see 6.5.2) in 80ms 8

broadcast slots (9600 bps) and repeat steps 5 through 9 using BCCH_7 instead of 9

BCCH_6. 10



BCCH_6. 13


The actual BCCH Eb/Nt values used in the test shall be within ±0.2 dB of the values 15

indicated in Table A.1.3.1-1 through A.1.3.1-3. 16

The Broadcast Control Channel FER is calculated by: 17

BCCH FER = 9_BCCHN_BCCH

9_BCCH∆+∆

∆ , 18

where ∆BCCH_9 is the increment of parameter BCCH_9 (i.e. insufficient physical layer 19

frame quality) during the test, and ∆BCCH_N is the increment of parameter BCCH_6, 20

BCCH_7, or BCCH_8 which is the appropriate counter for the successful demodulation of 21

the frame and coding structure being tested, and when added to the erased frames is the 22

total number of Broadcast Control Channel frames sent in the mobile station broadcast 23

slot during the test interval. 24

For each spreading rate and rate mode the mobile stations supports, the FER for each test 25

shall not exceed the piecewise linear FER curve specified by the points in Tables A.1.3.2-1 26

through A.1.3.2-3 with 95% confidence (see 6.6). 27

3.3.4 Demodulation of Broadcast Control Channel in Multipath Fading Channel 28


The performance of the demodulation of Broadcast Control Channel in multipath fading 30

channel with and without transmit diversity is determined by the frame error rate (FER). 31




3GPP2 C.S0011-C v2.0

3-41



3. For each Broadcast Control Channel spreading rate and code rate that the mobile 3

station supports, perform steps 4 through 12. 4

4. Send continuous messages on the Broadcast Control Channel in 40ms broadcast 5

slots (19200 bps). Overhead message contents shall be as specified in 6.5.2. 6

5. Set the test parameter values for each test as specified in Table A.1.4.1-1 through 7

A.1.4.1-20. 8



7. Have the base station increment either the CONFIG_MSG_SEQ or the 11

ACC_MSG_SEQ in the General Page Message sent on the F-CCCH on each paging 12

slot of the MS under test. 13






BCCH_6. 19



BCCH_6. 22

12. Repeat the test for each transmit diversity scheme (e.g. OTD or STS) supported by 23

the mobile station and set the following parameters in the Sync Channel Message: 24

25

Parameter Value (Binary)

SR1_TD_INCL ‘1’ (Transmit Diversity enabled)

SR1_TD_POWER_LEVEL ‘10’ (3 dB below the Forward Pilot Channel transmit power)

26


The actual power measurement uncertainty shall be less than or equal to 0.2 dB (see 6.6.2) 28

with the minimum test duration meeting the requirements specified in Table 6.6.2-1. Test 29

durations must be sufficient to meet confidence level requirements. 30

The actual BCCH Eb/Nt values used in the test shall be within ±0.2 dB of the values 31

indicated in Table A.1.4.1-1 through A.1.4.1-20. 32

The Broadcast Control Channel FER is calculated by: 33

3GPP2 C.S0011-C v2.0

3-42

BCCH FER = 9_BCCHN_BCCH

9_BCCH∆+∆

∆ , 1

where ∆BCCH_9 is the increment of parameter BCCH_9 (i.e. insufficient physical layer 2

frame quality) during the test, and ∆BCCH_N is the increment of parameter BCCH_6, 3

BCCH_7, or BCCH_8 and represents the appropriate counter for the successful 4

demodulation of the frame and coding structure being tested, and when added to the 5

erased frames is the total number of Broadcast Control Channel frames sent in the mobile 6

station broadcast slot during the test interval. 7

The FER for each test shall not exceed the piecewise linear FER curve specified by the 8

points in Tables A.1.4.2-1 through A.1.4.2-10 with 95% confidence (see 6.6). 9

3.3.5 Demodulation of Forward Common Control Channel 10

These tests shall be performed for mobile stations that support the Broadcast Control 11

Channel and the Forward Common Control Channel. The Quick Paging Channel shall be 12

disabled during these tests. 13


The performance of the demodulation of the Forward Common Control Channel in an 15

AWGN (no fading or multipath) environment is determined by the frame error rate (FER). 16






3. For each Forward Common Control Channel spreading rate and code rate that the 22

mobile station supports, perform steps 4 through 10. 23

4. Set MAX_SLOT_CYCLE_INDEX to 0 in the ANSI-41 System Parameters Message 24

(each slot cycle is 1.28 seconds long). 25

5. Send a General Page Message with no Page Records in the mobile station’s 26

assigned Forward Common Control Channel slot in every slot cycle. 27

6. Set the test parameters for each test as specified in Tables A.1.5.1-1 through 28

A.1.5.1-4. 29

7. Set up a call using Fundamental Channel Test Mode 3 (see 1.3) and retrieve the 30

parameters FCCCH_5 (tests 2, 5, 8, and 11), FCCCH_6 (tests 1, 4, 7, and 10), or 31

FCCCH_7 (tests 3, 6, 9, and 12), and FCCCH_11, and then end the call. 32

8. Run the test for at least seven minutes and 41 seconds and until sufficient 33

confidence is ensured. 34

3GPP2 C.S0011-C v2.0

3-43


parameters FCCCH_5 (tests 2, 5, 8, and 11), FCCCH_6 (tests 1, 4, 7, and 10), or 2

FCCCH_7 (tests 3, 6, 9, and 12), and FCCCH_11. 3


The actual power measurement uncertainty shall be less than or equal to 0.2 dB with the 5

minimum test duration meeting the power measurement uncertainty requirement. Test 6


The actual F-CCCH Eb/Nt used in each test shall be within ±0.2 dB of the value indicated 8

in A.1.5.1-1 through A.1.5.1-4. 9

The Forward Common Control Channel FER is calculated by: 10

F-CCCH FER = 11_FCCCHN_FCCCH

11_FCCCH∆+∆

∆ , 11

where ∆FCCCH_11 is the increment of parameter FCCCH_11 (i.e. insufficient physical layer 12

frame quality) during the test, and ∆FCCCH_N is the increment of the appropriate counter 13

for the successful demodulation of the frame and coding structure being tested, and when 14

added to the erased frames is the total number of Forward Common Control Channel 15

frames sent to the mobile station during the test. 16



3.3.6 Demodulation of Common Assignment Channel and Reception of Common Power 19

Control Channel 20

These tests shall be performed for mobile stations that support the Common Assignment 21

Channel and Common Power Control Channel. 22


When operating in the Reservation Access Mode, the mobile station monitors the Common 24

Assignment Channel after transmitting the preamble on the Enhanced Access Channel. 25

Once the Early Acknowledgement Channel Assignment Message is received, the mobile 26

station starts transmitting the access message on the Reverse Common Control Channel, 27

which is power controlled by the Common Power Control Channel. The following tests verify 28

that the mobile station has proper demodulation performance of the Common Assignment 29

Channel and reception of the Common Power Control Channel in an AWGN environment. 30

The performance of the demodulation of the Common Assignment Channel in an AWGN (no 31

fading or multipath) environment is determined by the frame error rate (FER). The 32

performance of the reception of the Common Power Control Channel is determined by the 33

compliance of the mobile station transmit power with the assigned power control 34

subchannel power control bits. 35

3GPP2 C.S0011-C v2.0

3-44






3. For each Common Assignment Channel spreading rate and code rate that the 6

mobile station supports, perform steps 4 through 13. 7

4. Set the following values in the Enhanced Access Parameters Message: 8

9


ACCESS_MODE 1 (Reservation Access Mode)

APPLICABLE_MODES 2 (Parameters are for Reservation Access Mode)

CACH_CODE_RATE As specified in the test

RA_PC_DELAY 4 (MS to ignore 4 PC bits after start of RCCCH transmission)

RCCCH_HO_SUPPORTED 0 (RCCCH handoff disabled)

CPCCH_RATE 2 (800 bps CPCCH power control rate)

RA_CPCCH_STEP_UP 2 (up step size is 1 dB)

RA_CPCCH_STEP_DN 2 (down step size is 1 dB)

NUM_PCSCH_RA 24 (24 Power Control Subchannels)

10

5. Send a Status Request Order on the Forward Common Control Channel. 11

6. Once the end of the header on the Enhanced Access Channel is detected, send an 12

Early Acknowledgement Channel Assignment Message on the Common Assignment 13

Channel addressed to the mobile station. 14

7. Send a periodic pattern of twenty ‘0’ power control bits followed by twenty ‘1’ power 15

control bits on the Common Power Control Subchannel assigned to the mobile 16

station. 17

8. Set the test parameter values as specified in Table A.1.6.1-1 through A.1.6.1-3. 18


parameter CACH_2, and then end the call. 20

10. Count, at the base station, the number of frames transmitted to the mobile station 21

on the Common Assignment Channel. 22

11. Monitor the mobile station transmission and its power level on the Reverse 23

Common Control Channel. 24

3GPP2 C.S0011-C v2.0

3-45



parameter CACH_2. 3





The actual CACH Eb/Nt and CPCCH Eb/Nt values used in the test shall be within ±0.2 dB 8

of the values indicated in Table A.1.6.1-1 through A.1.6.1-3. 9

The Common Assignment Channel FER is calculated by: 10

CACH FER = ansmitted_Frames_TrTotal_CACH

2_CACH∆ , 11

where ∆CACH_2 is the increment of parameter CACH_2 (i.e. insufficient physical layer 12

frame quality) during the test, and Total_CACH_Frames_Transmitted is the total number of 13

Common Assignment Channel frames sent to the mobile station during the test. 14



For all tests, the mobile station output power on the Reverse Common Control Channel, 17

measured at the mobile station antenna connector, shall have a periodic pattern. In each 18

period the power shall increase monotonically for a duration of 20 power control groups 19

and then decrease monotonically for a duration of 20 power control groups. 20

3.3.7 Demodulation of Forward Packet Data Control Channel in Additive White Gaussian 21

Noise 22

This test shall be performed on the Forward Packet Data Control Channel, if the Forward 23

Packet Data Control Channel is supported by the mobile station. 24


The demodulation performance of Forward Packet Data Control Channel in AWGN is 26

determined by the frame error rate (FER). The FER is calculated for each individual data 27

rate. 28

If the mobile station supports the Forward Fundamental Channel, then the base station 29

shall transmit the Forward Fundamental Channel, which will contain the power control 30

subchannel. Otherwise, the base station shall transmit the Forward Dedicated Control 31

Channel, which will contain the power control subchannel. The forward link closed loop 32

power control shall be disabled in the base station. The base station shall set the Forward 33

Packet Data Control Channel transmission format independent of the data received on the 34

Reverse Channel Quality Indicator Channel and the Reverse Acknowledgment Channel. 35

3GPP2 C.S0011-C v2.0

3-46


1. Connect the base station and an AWGN generator to the mobile station antenna 2




3. Set up a call using Packet Data Channel Test Mode 10a (see 1.3). Configure the 6

base station to send fixed duration messages on the Forward Packet Data Control 7

Channel. Configure the base station to send the Forward Packet Data Control 8

Channel messages on the maximum number of ARQ Channels supported by the 9

mobile station with a duty cycle on those channels equal to 100%. Configure the 10

base station so that it sets the MAC_ID field to the value assigned to the mobile 11

station in all messages sent on the Forward Packet Data Control Channel. 12

4. Configure the base station to map the Layer 3 Signaling messages only onto the 13

Forward Fundamental Channel or Forward Dedicated Control Channel. 14

5. Set up the test parameters for each test as specified in 3.3.7.2-1. 15

6. Count, at the base station, the number of Forward Packet Data Control Channel 16

frames transmitted, and the number of Forward Packet Data Control Channel good 17

frames received at the mobile station. A good frame is one that passes the CRC 18

check and matches the mobile station’s assigned MAC_ID. 19

20

3GPP2 C.S0011-C v2.0

3-47

Table 3.3.7.2-1. Test Parameters for Forward Packet Data Control Channel in AWGN 1

Parameter Units Test 1 Test 2 Test 3

Îor/Ioc dB -1

orc

IE Pilot

dB -7

orc

IE Sync

dB -16

orc

IEPaging

dB -12

orc

IE FCH

dB -16.2

orc

IE PDCCH

dB -11.2 -15.2 -18.5

Ioc dBm/1.23MHz -54

Data Rate bps 29600 (1.25ms) 14800 (2.5ms) 7400 (5ms)

tb

NE PDCCH

dB 3.9 3.0 2.7

2





The actual Forward Packet Data Control Channel Eb/Nt used in each test shall be within 7

±0.2 dB of the value indicated in Table 3.3.7.2-1. 8


points in Table 3.3.7.3-1 with 95% confidence. 10

11

3GPP2 C.S0011-C v2.0

3-48

Table 3.3.7.3-1. Minimum Standards for Radio Configuration 10 Forward Packet Data 1

Control Channel Performance in AWGN 2

Test Data Rate [bps]

F-PDCCH Eb/Nt [dB] FER

3.0 0.05

1 29600 3.9 0.01

4.2 0.005

2.1 0.05

2 14800 3.0 0.01

3.2 0.005

1.9 0.05

3 7400 2.7 0.01

3.1 0.005

3

3.3.8 Demodulation of Forward Packet Data Control Channel in Soft and Softer Handoff 4


The mobile station indicates the selected serving sector with the R-CQICH cover. The 6

mobile station selects the serving sector based on the estimated pilot signal-to-noise ratio. 7

There are four tests. Test 1 and Test 2 verify the mobile station switches serving sector to 8

maintain data throughput. Test 1 verifies switching between co-located sectors (softer 9

switch). Test 2 verifies switching between non co-located sectors (soft switch). Tests 3 and 10

4 verify the mobile station does not switch serving sectors so fast that it does not receive 11

packets from any sector. Test 3 verifies switching between co-located sectors (softer 12

switch). Test 4 verifies handoff between non co-located sectors (soft switch). The 13

parameters PDCH_SOFT_SWITCHING_DELAY and PDCH_SOFTER_SWITCHING_DELAY 14

determine the time the base station will take to redirect data from one serving sector to 15

another. 16


1. Connect two base stations (two sectors) to the mobile station as shown in Figure 18

6.5.1.3. The Forward Channel from sector 1 has an arbitrary pilot PN offset index 19

P1, and is called Channel 1. The Forward Channel from sector 2 has an arbitrary 20

pilot PN offset index P2, and is called Channel 2. 21

2. Configure the mobile station to operate in a band class it supports. 22

3. Set the base station so as not to send any Extended Handoff Direction Message or 23

General Handoff Direction Message or Universal Handoff Direction Message as a 24

response to the Pilot Strength Measurement Message or Extended Pilot Strength 25

Measurement Message sent by the mobile station. 26

3GPP2 C.S0011-C v2.0

3-49

4. Set up a call using Packet Data Channel Test Mode 10a (see 1.3). Set the test 1

parameters as specified in Table 3.3.8.2-1 and Figure 3.3.8.2-1. Configure each 2

base station to send one slot length messages on the Forward Packet Data Control 3

Channel. Configure each base station to send the Forward Packet Data Control 4

Channel messages on the maximum number of ARQ Channels supported by the 5

mobile station with a duty cycle on those channels equal to 100%. Configure each 6

base station to set the MAC_ID field to the value assigned to the mobile station in 7

all messages sent on the Forward Packet Data Control Channel while it is in state 8

S1; and to set the MAC_ID field to a value other than that assigned to the mobile 9

station in all messages sent on the Forward Packet Data Control Channel while it 10

is in state S2. 11

5. For Test 1, perform Steps 6 and 7. 12

6. Send an Extended Channel Assignment Message to the mobile station, specifying 13

the following parameters: 14

15


NUM_SOFT_SWITCHING_FRAMES 0 (1 frames)

NUM_SOFTER_SWITCHING_FRAMES 0 (1 frames)

PDCH_SOFT_SWITCHING_DELAY 15 (160 ms)

PDCH_SOFTER_SWITCHING_DELAY 0 (10 ms)

PILOT_PN P1

PWR_COMB_IND 0

PDCH_GROUP_IND 0

PILOT_PN P2

PWR_COMB_IND 1 (softer handoff)

PDCH_GROUP_IND 1 (softer reselection parameters)

ARIB STD-T64-C.S0011-C v2.0 Recommended …...1 Original Specification 2 This standard, ARIB...

Documents

Transcript of ARIB STD-T64-C.S0011-C v2.0 Recommended …...1 Original Specification 2 This standard, ARIB...