ARCAT, Inc. · Web viewFalling Dart Impact per ANZI/SAE Z26.1 Dart; Single Impact Vertical Drop,...

SECTION 08 84 00

PLASTIC GLAZING INCLUDING MULTIWALL, FRAMING, AND ACCESSORIES

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2019 - 2021 ARCAT, Inc. - All rights reserved

** NOTE TO SPECIFIER ** A&C Plastics, Inc.; plexiglass acrylic, and polycarbonate sheets.This section is based on the products of A&C Plastics, Inc., which is located at:6135 NorthdaleHouston, TX 77087Toll Free Tel: 888-702-6028Email: request info ([email protected])Web: https://www.acplasticsinc.com [ Click Here ] for additional information.A&C Plastics is dedicated to helping you with your plastic needs from the selection process to purchasing and even providing advice when you need it. With the sheer number of available plastic solutions for every application, it's often difficult to decide which acrylic, polycarbonate or specialty plastic sheet is right for your project. Plastics are widely used to replace glass in all industries from food service to retailers, banks to personal use, because of the versatility, durability and reliability these materials feature.

1 GENERAL

1.1 SECTION INCLUDES

** NOTE TO SPECIFIER ** Delete items below not required for project.

1.1.1 Acrylic sheets.

1.1.2 Polycarbonate sheets.

1.1.3 Multiwall Polycarbonate sheets.

1.1.4 Framing Systems and accessories.

1.2 RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

1.2.1 Section 07 91 23 - Backer Rods.

1.2.2 Section 08 40 00 - Entrances, Storefronts, and Curtain Walls.

1.2.3 Section 11 98 21 - Detention Windows.

1.2.4 Section 08 57 00 - Hurricane Resistant Windows*.

1.2.5 Section 08 81 13 - Decorative Glass Glazing.

1.2.6 Section 08 83 00 - Mirrors.

1.2.7 Section 08 88 56 - Ballistics-Resistant Glazing.

1.2.8 Section 08 88 56 - Ballistic Resistant Glazing.

1.2.9 Section 08 44 23 - Structural Sealant Glazed Curtain Wall.

1.3 REFERENCES

** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

1.3.1 ASTM International (ASTM): Standard Test Methods.

1.3.1.1 ASTM C177 - For Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus.

1.3.1.2 ASTM D149 - For Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies.

1.3.1.3 ASTM D150 - For AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation.

1.3.1.4 ASTM D256 - For Determining the Izod Pendulum Impact Resistance of Plastics.

1.3.1.5 ASTM D257 - For DC Resistance or Conductance of Insulating Materials.

1.3.1.6 ASTM D495 - For High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation.

1.3.1.7 ASTM D542 - For Index of Refraction of Transparent Organic Plastics.

1.3.1.8 ASTM D570 - For Water Absorption of Plastics.

1.3.1.9 ASTM D635 - For Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position.

1.3.1.10 ASTM D638 - For Tensile Properties of Plastics.

1.3.1.11 ASTM D648 - For Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position.

1.3.1.12 ASTM D695 - For Compressive Properties of Rigid Plastics.

1.3.1.13 ASTM D696 - For Coefficient of Linear Thermal Expansion of Plastics Between 30C and 30C with a Vitreous Silica Dilatometer.

1.3.1.14 ASTM D732 - For Shear Strength of Plastics by Punch Tool.

1.3.1.15 ASTM D746 - For Brittleness Temperature of Plastics and Elastomers by Impact.

1.3.1.16 ASTM D785 - For Rockwell Hardness of Plastics and Electrical Insulating Materials.

1.3.1.17 ASTM D790 - For Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials.

1.3.1.18 ASTM D792 - For Density and Specific Gravity (Relative Density) of Plastics by Displacement.

1.3.1.19 ASTM D1003 - For Haze and Luminous Transmittance of Transparent Plastics.

1.3.1.20 ASTM D1929 - For Determining Ignition Temperature of Plastics.

1.3.1.21 ASTM D1044 - For Resistance of Transparent Plastics to Surface Abrasion.

1.3.1.22 ASTM D1746 - For Transparency of Plastic Sheeting.

1.3.1.23 ASTM D1929 - For Determining Ignition Temperature of Plastics.

1.3.1.24 ASTM D3763 - For High Speed Puncture Properties of Plastics Using Load and Displacement Sensors.

1.3.1.25 ASTM E84 - For Surface Burning Characteristics of Building Materials.

1.3.1.26 ASTM E132 - For Poisson's Ratio at Room.

1.3.1.27 ASTM E162 - For Surface Flammability of Materials Using a Radiant Heat Energy Source.

1.3.1.28 ASTM E662 - For Specific Optical Density of Smoke Generated by Solid Materials.

1.3.1.29 ASTM F1233 - For Security Glazing Materials And Systems.

1.3.1.30 ASTM F1915 - For Glazing for Detention Facilities.

1.3.1.31 ASTM F1913 - Standard Specification for Vinyl Sheet Floor Covering Without Backing.

1.3.2 American National Standards Institute (ANSI):

1.3.2.1 ANSI Z26. - American National Standard for Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways - Safety Code.

1.3.3 Building Officials and Code Administrators International, Inc. (BOCA).

1.3.4 European Standard (EN):

1.3.4.1 EN14500 - Blinds and shutters. Thermal and visual comfort. Test and calculation methods.

1.3.5 European Union's Directive 2002/95/EC, the Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (RoHS).

1.3.6 Food and Drug Administration (FDA):

1.3.6.1 FDA 21 CFR Part 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

1.3.7 International Conference of Building Officials (ICBO).

1.3.8 International Electrotechnical Commission (IEC):

1.3.8.1 IEC 93 - Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials.

1.3.8.2 IEC 243 - Methods of test for electric strength of solid insulating materials - Part 1: Test at power frequencies.

1.3.9 International Standards Organization (ISO):

1.3.9.1 ISO 62 - Plastics - Determination Of Water Absorption.

1.3.9.2 ISO 178 - Plastics - Determination Of Flexural Properties.

1.3.9.3 ISO 179 - Plastics - Determination Of Charpy Impact Properties - Part 1: Non-Instrumented Impact Test.

1.3.9.4 ISO 180 - Plastics - Determination of Izod impact strength.

1.3.9.5 ISO 306 - Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST).

1.3.9.6 ISO 489A - Plastics - Determination Of Refractive Index.

1.3.9.7 ISO 527 - Plastics - Determination Of Tensile Properties - Part 1: General Principles.

1.3.9.8 ISO 717 - Acoustics - Rating of sound insulation in buildings and of building elements - Part 1: Airborne sound insulation.

1.3.9.9 ISO 1183 - Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pycnometer method and titration method;

1.3.9.10 ISO 2039- Plastics - Determination of hardness - Part 1: Ball indentation method.

1.3.10 United State Military Standard Commercial Item Description (CID):

1.3.10.1 CID A-A-59502 - Plastic Sheet , Polycarbonate.

1.3.11 National Fenestration Rating Council (NFRC):

1.3.11.1 NFRC 100 - Procedure for Determining Fenestration Product U-Factors

1.3.12 National Oceanic and Atmospheric Administration (NOA)

1.3.13 Underwriters Laboratories (UL):

1.3.13.1 UL 94 - Standard for Tests for Flammability of Plastic Materials for Parts in Devices and Appliances.

1.3.13.2 UL 752 - Standard for Bullet-Resisting Equipment.

1.4 SUBMITTALS

1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.4.2 Product Data:

1.4.2.1 Manufacturer's data sheets on each product to be used.

1.4.2.2 Preparation instructions and recommendations.

1.4.2.3 Storage and handling requirements and recommendations.

1.4.2.4 Typical installation methods.

** NOTE TO SPECIFIER ** Delete if not applicable to product type.

1.4.3 Verification Samples: Two representative units of each type, size, pattern and color.

1.4.4 Shop Drawings: Include details of materials, construction and finish. Include relationship with adjacent construction.

1.5 QUALITY ASSURANCE

1.5.1 Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with a minimum five years documented experience.

1.5.2 Installer Qualifications: Company specializing in performing Work of this section with minimum two years documented experience with projects of similar scope and complexity.

1.5.3 Source Limitations: Provide each type of product from a single manufacturing source to ensure uniformity.

** NOTE TO SPECIFIER ** Include mock-up if the project size or quality warrant the expense. The following is one example of how a mock-up on might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.

1.5.4 Mock-Up: Construct a mock-up with actual materials in sufficient time for Architect's review and to not delay construction progress. Locate mock-up as acceptable to Architect and provide temporary foundations and support.

1.5.4.1 Intent of mock-up is to demonstrate quality of workmanship and visual appearance.

1.5.4.2 If mock-up is not acceptable, rebuild mock-up until satisfactory results are achieved.

1.5.4.3 Retain mock-up during construction as a standard for comparison with completed work.

1.5.4.4 Do not alter or remove mock-up until work is completed or removal is authorized.

1.6 PRE-INSTALLATION CONFERENCE

1.6.1 Convene conference two weeks before scheduled commencement of Work. Attendees to include Architect, Contractor and trades involved. Agenda shall include schedule, responsibilities, critical path items and approvals.

1.7 DELIVERY, STORAGE, AND HANDLING

1.7.1 Store and handle in compliance with manufacturer's instructions and recommendations.

1.7.2 Protect from damage due to weather, excessive temperature, and construction operations.

1.8 PROJECT CONDITIONS

1.8.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: A&C Plastics, Inc., which is located at: 6135 Northdale; Houston, TX 77087; Toll Free Tel: 888-702-6028; Email: request info ([email protected]); Web: https://www.acplasticsinc.com

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

2.1.2 Substitutions: Not permitted.

2.1.3 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

** NOTE TO SPECIFIER ** Delete article if not required.

2.2 ACRYLIC SHEETS

** NOTE TO SPECIFIER ** Superior clarity and durability. For signage, aquariums, construction applications, windows and general use. Delete if not required.

2.2.1 Basis of Design: Acrystar Acrylic Sheets: UV stable and suitable for interior and exterior applications.

2.2.1.1 General Properties:

2.2.1.1.1 ROHS compliant. None of the following elements, chemicals, or compounds are to be a part of the manufacturing process or acrylic sheets; Cadmium, Lead, Mercury, Chromium, PBB, PBDE, Other Bromine compounds.

2.2.1.1.2 FDA Approval: Code 21CFR177.1010.

2.2.1.1.3 Relative Density per ISO 1183: 0.688 oz per cu inch (1.19 g per cu cm).

2.2.1.1.4 Water Absorption per ISO 62: 0.3 percent.

2.2.1.2 Mechanical Properties: At 73 degrees F (23 degrees C).

2.2.1.2.1 Tensile Strength per ISO 527: 10153 psi (70 MPa).

2.2.1.2.2 Elongation at Break per ISO 527: 4 percent.

2.2.1.2.3 Flexural Strength per ISO 178: 16534 psi (114 MPa).

2.2.1.2.4 Flexural Modulus per ISO 178: 464121 psi (3200 MPa).

2.2.1.2.5 Impact Strength: Charpy-unnotched per ISO 179: 12 kJ sq m.

2.2.1.2.6 Izod Impact Strength, notched per ISO 180: 1.4 kJ sq m.

2.2.1.2.7 Rockwell Hardness per ISO 2039-2: 100 M scale.

2.2.1.2.8 Strain: At Room Temperature:

2.2.1.2.8.1 Clear: 94.727 psi (6.66 kg per sq cm).

2.2.1.2.8.2 Colored: 129.717 psi (8.12 kg per sq cm).

2.2.1.2.9 Strain: At 32 degrees F (0 degrees C):



2.2.1.2.10 Strain: Sun Drying:



2.2.1.2.11 Friction: At Room Temperature:



2.2.1.2.12 Friction: Sun Drying:



2.2.1.2.13 Friction: Graving:

2.2.1.2.13.1 Clear: 22.847 lbs per inch (4.08 kg/cm).

2.2.1.2.13.2 Colored: 34.270 lbs per inch (6.12 kg/cm).

2.2.1.2.14 Friction: Curving Movement:

2.2.1.2.14.1 Clear: 347.884 lbs per inch (62.125 kg/cm).

2.2.1.2.14.2 Colored: 292.586 lbs per inch (.2.25 kg/cm).

2.2.1.2.15 Friction: Melting Point:

2.2.1.2.15.1 Clear: 191.3 degrees F (88.5 degrees C).

2.2.1.2.15.2 Colored: 181.4 degrees F (83 degrees C).

2.2.1.2.16 Expansion: At 75 to 86 degrees F (24 to 30 degrees C):

2.2.1.2.16.1 Clear: 5/10-5 mm/mm degree C.

2.2.1.2.16.2 Colored: 6.5/10-5 mm/mm degree C.

2.2.1.2.17 Expansion: At 86 to 185 degrees F (30 to 85 degrees C):

2.2.1.2.17.1 Clear: 9/10-5 mm/mm degree C.

2.2.1.2.17.2 Colored: 9.5/10-5 mm/mm degree C.

2.2.1.2.18 Expansion: Flamation: Clear: None. Colored: None.

2.2.1.2.18.1 Expansion: Hardness: 264.532 lbs per inch (47.24 kg per cm).Clear: 56.Colored: 54.4.

2.2.1.2.19 Transparency: Original: Clear: 0. Colored: 15.8.

2.2.1.2.20 Transparency: After Drying: Clear: 92.5 percent. Colored: 16 percent.

2.2.1.2.21 Specific Gravity:

2.2.1.2.21.1 Clear: 0.043 lbs per cu inch (1.19 grams per cu cm).

2.2.1.2.21.2 Colored: 0.069 lbs per cu inch (1.9 grams per cu cm).

2.2.1.3 Thermal Properties:

2.2.1.3.1 Vicat Softening Point, ISO 306 A: 230 degrees F (110 degrees C).

2.2.1.3.2 Coefficient of Thermal Expansion, ASTM D696-44: 0.0000389 in/in/F (0.00007 cm/cm/C).

2.2.1.3.3 Flammability, UL94: HB.

2.2.1.4 Optical Properties: UV stable.

2.2.1.4.1 Light Transmission, ASTM D1003: 92 percent; 0.125 inch (3 mm).

2.2.1.4.2 Refractive Index, ISO 489 A: 1.49.

2.2.1.5 Electrical Properties:

2.2.1.5.1 Surface Resistivity, IEC 93: 1014 Ohms.

2.2.1.5.2 Electrical Strength, IEC 243: 30 kV/mm.

** NOTE TO SPECIFIER ** Delete sheet size and sheet thickness options not required.

2.2.1.6 Sheet Size (W x L): 48 x 96 inch (1219 x 2438 mm).

2.2.1.7 Sheet Size (W x L): ____ x ____ inch (____ x ____ mm).

2.2.1.8 Sheet Thickness: 0.125 inches (3.17 mm).Sheet Thickness: 0.187 inches (4.75 mm).

2.2.1.9 Sheet Thickness: 0.220 inches (5.59 mm).

2.2.1.10 Sheet Thickness: 0.375 inches (9.52 mm).

2.2.1.11 Sheet Thickness: 0.500 inch (12.70 mm).

2.2.1.12 Sheet Thickness: ____ inch (____ mm).

** NOTE TO SPECIFIER ** Delete finish options not required.

2.2.1.13 Finish: Clear:

2.2.1.14 Finish: P95. Clear Matte.

2.2.1.15 Finish: DP9. Clear Matte.

** NOTE TO SPECIFIER ** Processed with monomer. UV stable. For interior and exterior applications; signage, aquariums, construction applications, windows and general use. Delete if not required.

2.2.2 Basis or Design: Acrylic Sheets: UV stable and suitable for interior and exterior applications.

2.2.2.1 FDA Approval: FDA 21 CFR Part 177.1010. Can be in contact with food products.

2.2.2.2 General Properties:

2.2.2.2.1 ROHS Compliant.

2.2.2.2.2 Relative Density per ISO 1183: 1.19.

2.2.2.2.3 Water Absorption, ASTM D570-63: 0.3 percent.

2.2.2.2.4 Soluble Matter Lost after Immersion: None.

** NOTE TO SPECIFIER ** The following physical properties were determined by using 3 mm thickness of Trucast and 4 mm thickness of HHC High Impact.

2.2.2.3 Mechanical Properties:

2.2.2.3.1 Tensile Strength, ASTM D638-61 T.

2.2.2.3.1.1 Rupture: 10781.3 psi (758 kg per sq cm).

2.2.2.3.1.2 Modulus of Elasticity: 426700.8 psi (30000 kg per sq cm).

2.2.2.3.1.3 Elongation at Rupture: 4.5 percent.

2.2.2.3.2 Flexural Strength, D790-63.

2.2.2.3.2.1 Rupture: 17992.5 psi (1265 kg per sq cm).


2.2.2.3.3 Impact Strength, ASTM D256-56.

2.2.2.3.3.1 Falling Ball Impact: 11.4 psi (0.8 kg per sq cm).

2.2.2.3.3.2 Falling Dart Impact per ANZI/SAE Z26.1 Dart; Single Impact Vertical Drop, 196 grams at 6 feet: Passed. No visible damage.

2.2.2.3.4 Rockwell Hardness, ASTM D785-62: M 100.

2.2.2.3.5 Compressive Strength, ASTM D695-63T:

2.2.2.3.5.1 Yield: 17921.4 psi 91260 kg per sq cm).


2.2.2.3.6 Shear Strength, ASTM D732-46: 8889.6 psi 9625 kg per sq cm).

2.2.2.3.7 Specific Gravity, ASTM 792-60 T:

2.2.2.3.7.1 Clear: 0.043 lbs per cu inch (1.19 grams per cu cm).

2.2.2.3.7.2 Colored: 0.069 lbs per cu inch (1.9 grams per cu cm).


2.2.2.4.1 Hot Forming Temperature: 284 to 356 degrees F (140 to 180 degrees C).

2.2.2.4.2 Heat Distortion, ASTM D648 at Temperature 35.6 degrees F (2 degrees C) and 264 psi (1820 kPa): 212 degrees F (100 degrees C.).

2.2.2.4.3 Coefficient of Thermal Expansion, ASTM D696-44: 0.0000389 in/in/F (0.00007 cm/cm/C).

2.2.2.4.4 Burning Rate, ASTM D635: 1.3 inches (33 mm) per min.

2.2.2.4.5 Specific Heat: 0.35 BTU / lbs / degrees F (0.35 Cal / gr / degrees C).

2.2.2.5 Optical Properties: UV stable.

2.2.2.5.1 Light Transmission, ASTM D1003-61: Parallel: 92 percent (3 mm). Total: 93 percent. Haze: 1 percent.

2.2.2.5.2 Refractive Index, ASTM 542-50: 1.49.


2.2.2.6.1 Surface Resistivity at 82.4 degrees F (28 degrees C) and 75 percent Relative Humidity, ASTM D257: Less than 10E16 ohms.

2.2.2.6.2 Volume Resistivity Dielectric Strength, D257: 15E15 Ohm cm.

2.2.2.7 Short Time Test, ASTM D149-64: 20 kV/mm.

2.2.2.8 Arc Resistance, D495-61: No Track.

** NOTE TO SPECIFIER ** Delete sheet thickness and dimension options not required.

2.2.2.9 Sheet Thickness: 0.060 inch (1.5 mm). Color: Clear.

2.2.2.9.1 Dimensions (W x L): 48 x 96 inches (1219 x 2438 mm).





2.2.2.10 Sheet Thickness: 0.125 inch (3 mm).





2.2.2.10.5 Color: Clear.

2.2.2.10.6 Color: As determined by the Architect from manufacturer's standard offerings.















































2.2.2.18 Sheet Thickness: 1.000 inch (25.40 mm). Clear.
















** NOTE TO SPECIFIER ** Delete article if not required.

2.3 POLYCARBONATE SHEETS:

** NOTE TO SPECIFIER ** Typical glazing applications: Schools, hospitals, bus shelters, correctional, and psychiatric facilities. For view windows and machine guards in harsh chemical environments. Due to abrasion resistant coating, cannot be formed. Delete if not required.

2.3.1 Tuffak Polycarbonate, Tuffak AR. Abrasion and UV resistant sheet with glass-like surface and high impact strength. Resistant to yellowing and hazing.

2.3.1.1 Standards Compliance: CID A-A-59502. Type III; Marr Resistant, UV Stabilized Sheet, Class 1, Grade A, High abrasion.

2.3.1.2 Physical and Mechanical Properties:

2.3.1.2.1 Specific Gravity, ASTM D792: 1.2

2.3.1.2.2 Light Transmission, ASTM D1003: Clear 1/8 inch (3 mm) thick; 86 percent.

2.3.1.2.3 Light Transmission, ASTM D1003: Gray or Bronze; 50 percent.

2.3.1.2.4 Chemical Resistance, ANSI Z26.1: Pass.

2.3.1.2.5 Taber Abrasion, 100 Cycles CS10, ASTM D1044: 1 to 2 percent.

2.3.1.2.6 Tensile Strength, Ultimate , ASTM D638: 9,500 psi (65500 kPa).

2.3.1.2.7 Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).

2.3.1.2.8 Compressive Strength, ASTM D695: 12,500 psi (86184 kPa).

2.3.1.2.9 Modulus of Elasticity, ASTM D638: 340,000 psi (2344 MPa).

2.3.1.2.10 Poisson's Ratio: 0.38.

2.3.1.2.11 Izod Impact Strength, ASTM D256 at 1/8 inch (3 mm):

2.3.1.2.11.1 Notched: 12 to 16 Ft-lbs/in (0.64 to 0.85 Nm/mm).

2.3.1.2.11.2 Unnotched: 60 Ft-lbs/in (3.59 Nm/mm) No failure.

2.3.1.2.12 Instrumented Impact, ASTM D3763, 1/8 inch (3 mm): 45 ft-lbs (61 Nm).


2.3.1.3.1 Coefficient of Thermal Expansion, ASTM D696: 0.0000375 in/in/F.

2.3.1.3.2 Heat Deflection Temperature, ASTM D648, at 264 psi (1820 kPa): 270 degrees F (132 degrees C).

2.3.1.3.3 Heat Deflection Temperature,, ASTM D648, at 66 psi (455 kPa): 280 degrees F (138 degrees C).


2.3.1.4.1 Dielectric Constant, ASTM D150 at 10 Hz: 2.96.

2.3.1.4.2 Dielectric Constant, ASTM D150 at 60 Hz: 3.17.

2.3.1.4.3 Volume Resistivity, ASTM D257: 8.2 x 10E16 Ohm-cm.

2.3.1.4.4 Dissipation Factor, ASTM D150 at 60 Hz: 0.0009.

2.3.1.4.5 Dissipation Factor, ASTM D150 at 1 MHz: 0.01.

2.3.1.4.6 Arc Resistance, ASTM D495:

2.3.1.4.6.1 Stainless Steel Strip Electrode: 10 to 11 seconds.

2.3.1.4.6.2 Tungsten Electrodes: 120 seconds.

2.3.1.4.7 Dielectric Strength, ASTM D149: In air, 125 mils: 380 V/mil.

2.3.1.5 Flammability:

2.3.1.5.1 Horizontal Burn, AEB, ASTM D635: Less than 1 inch (25 mm).

2.3.1.5.2 Ignition Temperature, ASTM D1929:

2.3.1.5.2.1 Self: 1070 degrees F (576.7 degrees C).

2.3.1.5.2.2 Flash: 870 degrees F (465.6 degrees C).

2.3.1.5.3 Flame Class, Ul 94 at 0.060 inch (1.5 mm) and 0.236 inch (6 mm): HB.

** NOTE TO SPECIFIER ** Food applications; processing equipment guards, bulk bins, candy molds, sneeze guards, serving bowls, and service accessories. Medical applications; single use autoclave packaging, hospital trays, bassinets, incubators, and storage containers.

2.3.2 Tuffak Polycarbonate, Tuffak FD. Clear, non-UV stabilized sheet, complying with FDA and NSF 51 requirements. Close gauge tolerance control, high impact strength and heat resistance. Suitable for medical and food processing environments.

2.3.2.1 Standards Compliance: CID A-A-59502. Type 1, Class 2, Non-UV Stabilized.

2.3.2.2 Physical and Mechanical Properties:

2.3.2.2.1 Specific Gravity, ASTM D792: 1.2.

2.3.2.2.2 Light Transmission, ASTM D1003, Clear 1/8 inch (3 mm): 86 percent.

2.3.2.2.3 Water Absorption, ASTM D570, Equilibrium, 24 hours: 0.15 percent.

2.3.2.2.4 Impact Resistance: 250 times that of float glass. 30 times that of acrylic.

2.3.2.2.5 Tensile Strength, Yield, ASTM D638: 9000 psi (62053 kPa).

2.3.2.2.6 Tensile Strength, Ultimate, ASTM D638: 9500 psi (65500 kPa).

2.3.2.2.7 Tensile Modulus, ASTM D638: 345000 psi (2378691 kPa).

2.3.2.2.8 Flexural Strength, ASTM D790: 13500 psi (93079 kPa).

2.3.2.2.9 Flexural Modulus, ASTM D790: 345000 psi (2378691 kPa).

2.3.2.2.10 Compressive Strength, ASTM D695: 12500 psi (86184 kPa).

2.3.2.2.11 Compressive Modulus, ASTM D695: 345000 psi (2374691 kPa).

2.3.2.2.12 Elongation, ASTM D63: 110 percent.

2.3.2.2.13 Poisson's Ratio: 0.38





2.3.2.3.1 Coefficient of Thermal Expansion, ASTM D696: 0.0000375 in/in/degrees F (0.0000675 mm/mm/degrees C).

2.3.2.3.2 Coefficient of Thermal Conductivity, ASTM C177: 1.35 Btu/hr/sq ft/F (7.66 W/sq m/C).

2.3.2.3.3 Heat Deflection Temperature, ASTM D648 at 264 psi: 270 degrees F (132 degrees C).

2.3.2.3.4 Heat Deflection Temperature, ASTM D648 at 66 psi: 280 degrees F (138 degrees C).


2.3.2.4.1 Dielectric Constant, at 10 Hz ASTM D150: 2.96.

2.3.2.4.2 Dielectric Constant, at 60 Hz ASTM D150: 3.17.

2.3.2.4.3 Volume Resistivity ASTM D257: 8.2 x 10E16 Ohm-cm.

2.3.2.4.4 Dissipation Factor, at 60 Hz ASTM D150: 0.0009.

2.3.2.4.5 Dissipation Factor, at 1 MHz ASTM D150: 0.01.

2.3.2.4.6 Arc Resistance, ASTM D495: Stainless Steel Strip Electrode: 10 to 11 seconds. Tungsten Electrodes: 120 seconds.

2.3.2.5 Dielectric Strength, ASTM D149, in air, 125 mils (3.17 mm): 380 V/mil.

** NOTE TO SPECIFIER ** Industrial glazing, machine guards, structural parts, thermoformed and fabricated components.

2.3.2.6 Tuffak Polycarbonate, Tuffak GP. Polished surface, UV stabilized, and transparent lightweight thermoformable sheet. High impact strength, dimensionally stable, temperature resistance. Easy to fabricate and decorate. Limited Product Warranty: Five year against breakage. Standards Compliance: CID A-A-59502. Type 1, , Class 1, UV Stabilized.

2.3.2.7 Physical Mechanical Properties:


2.3.2.7.2 Refractive Index, ASTM D542: 1.586.

2.3.2.7.3 Light Transmission, ASTM D1003:

2.3.2.7.3.1 Clear at 0.118 inch (3 mm): percent.

2.3.2.7.3.2 Gray, I30 at 0.118 inch (3 mm): 50 percent.

2.3.2.7.3.3 Bronze, K09 at 0.118 inch (3 mm): 50 percent.

2.3.2.7.3.4 Dark Gray, I35 at 0.118 inch (3 mm): 18 percent.

2.3.2.7.3.5 Water Absorption, ASTM D 570 after 24 hours: 0.15 percent.

2.3.2.7.4 Poisson's Ratio, ASTM E132: 0.38.

2.3.2.7.5 Tensile Strength, Ultimate, ASTM D638: 9,500 psi (65500 kPa).

2.3.2.7.6 Tensile Strength, Yield, ASTM D638: 9,000 psi (62053 kPa).

2.3.2.7.7 Tensile Modulus, ASTM D638: 340,000 psi (2344217 kPa).



2.3.2.7.10 Flexural Modulus, ASTM D790: 345,000 psi (2378691 kPa).


2.3.2.7.12 Compressive Modulus, ASTM D695: 345,000 psi (2378691 kPa).


2.3.2.7.13.1 Notched: 18 Ft-lbs/in (0.96 Nm/mm).


2.3.2.7.14 Instrumented Impact, ASTM D3763 at 0.125 inch (3 mm): 47 ft-lbs (63.72 Nm).

2.3.2.7.15 Shear Strength, Ultimate, ASTM D732: 10,000 psi (68947 kPa).

2.3.2.7.16 Shear Strength, Yield, ASTM D732: 6,000 psi (41368 kPa).

2.3.2.7.17 Shear Modulus, ASTM D732: 114,000 psi (7860002 kPa).

2.3.2.7.18 Rockwell Hardness, ASTM D785: M70 and R118


2.3.2.8.1 Coefficient of Thermal Expansion, ASTM D696: 0.0000375 inch per inch per degrees F.

2.3.2.8.2 Coefficient of Thermal Conductivity, ASTM C177: 1.35 BTU/hr/sq ft/degrees F (7.66 (W/sq m/degrees C).

2.3.2.8.3 Heat Deflection Temperature, ASTM D648: At 264 psi (1820 kPa): 270 degrees F. At 66 psi (455 kPa): 280 degrees F.

2.3.2.8.4 Brittleness Temperature, ASTM D746: Minus 200 degrees F (minus 129 degrees C).

2.3.2.8.5 Shading Coefficient, NFRC 100 at 0.236 inch (6 mm) Thick: Clear; 0.97. Gray or Bronze; 0.77.

2.3.2.8.6 U factor, NFRC 100 at 0.236 inch (6 mm):

2.3.2.8.6.1 Summer: 0.85 BTU/hr/sq ft/degrees F (4.82 W/sq m/degrees C).

2.3.2.8.6.2 Winter: 0.92 BTU/hr/sq ft/degrees F (5.22 W/sq m/degrees C).

2.3.2.8.7 U factor, NFRC 100 at 0.375 inch (9.5 mm):




2.3.2.9.1 Dielectric Constant, ASTM D150 at 10 Hz: 2.96. At 60 Hz: 3.17.



2.3.2.9.4 Arc Resistance, ASTM D495: Stainless Steel Strip electrode: 10 seconds. Tungsten Electrodes: 120 seconds.

2.3.2.9.5 Dielectric Strength, ASTM D149 in air at 0.125 inch (3 mm): 380 V/mil.



2.3.2.10.2 Ignition Temperature, ASTM D1929: Self: 1022 degrees F (550 degrees C). Flash: 824 degrees F (440 degrees C).

2.3.2.10.3 Flame Class, UL 94 at 0.060 inches (1.5 mm): HB. At 0.394 inches (10 mm): V-0.

** NOTE TO SPECIFIER ** Government and detention facilities, banks, heavy equipment glazing, specialty retailers, 24 hour convenience stores, cash transaction windows.

2.3.3 Tuffak Polycarbonate, Hygard BR1000 sheet. Ballistic glazing, 4-ply laminate. Resists spalling, marring, chemical attack, graffiti and white-out after ballistic impacts.

2.3.3.1 Limited Product Warranty: 7 year against coating failure, yellowing, and hazing.

2.3.3.2 Four-Ply Construction:

2.3.3.2.1 Tuffak AR-1: 1/8 inch (3 mm) abrasion resistant surface.

2.3.3.2.2 Tuffak: 3/8 inch (9.5 mm) polycarbonate sheet.

2.3.3.2.3 Tuffak: 3/8 inch (9.5 mm) polycarbonate sheet.

2.3.3.2.4 Tuffak AR-1: 1/8 inch (3 mm) abrasion resistant surface.

2.3.3.2.5 Polyurethane bonding interlayers.

2.3.3.3 Properties:

2.3.3.3.1 Gauge: 1.05 inches (26.7 mm) plus or minus 5 percent.

2.3.3.3.2 Weight 6.5 lbs per sq ft (31.74 kg per sq m).

2.3.3.3.3 Shading Coefficient: 0.85.

2.3.3.3.4 U-Value 0.60.

2.3.3.3.5 Light Transmission 72 percent.

2.3.3.4 Ballistic Property: UL 752 Level 2 (.357 Magnum jacketed lead soft point).

2.3.3.5 Forced Entry and Containment:

2.3.3.5.1 ASTM F 1233.08 Class 5 Body Passage, and Class 2.4 Contraband Passage.

2.3.3.5.2 ASTM F 1915.03 Grade 1.

2.3.3.5.3 H.P. White TP 0500.03 Level IV Sequence 43.

2.3.3.6 Agency Information:

2.3.3.6.1 UL File: BP6864.

2.3.3.6.2 Combustibility Class CC1.

2.3.3.6.3 Miami-Dade NOA: 12-0605.05.

** NOTE TO SPECIFIER ** Delete sheet size options not required.

2.3.3.7 Sheet Size: 48 x 60 inch (1219 x 1524 mm).







** NOTE TO SPECIFIER ** Laminate used as containment and bullet-resistant glazing in higher level security applications, 24-hour convenience stores, specialty retailers, banks, and detention facilities,

2.3.4 Tuffak Polycarbonate, Hygard BR1250 four-ply sheet. Security. UL Listed Level III bullet-resisting glazing. Hard coated with abrasion and UV resistant surfaces for extended service life in harsh environments.

2.3.4.1 Forced Entry Ballistics Ratings:

2.3.4.1.1 H.P. WHITE TP0500.01 Level V.

2.3.4.1.2 H.P. WHITE TP0500.01 Level C Ballistics (.44 magnum).

2.3.4.1.3 ASTM F 1233 Class V Step 38 Ballistics (.44 magnum).

2.3.4.1.4 UL752 Level III SPSA .44 Magnum.

2.3.4.2 Four-ply Construction:

2.3.4.2.1 Tuffak AR: 1/8 inch (3 mm) abrasion resistant surface.

2.3.4.2.2 Tuffak: 1/2 inch (13 mm) polycarbonate sheet.

2.3.4.2.3 Tuffak: 1/2 inch (13 mm) polycarbonate sheet.

2.3.4.2.4 Tuffak AR: 1/8 inch (3 mm) abrasion resistant surface.



2.3.4.2.7 Self-Ignition Temperature, ASTM D1929: 1077 degrees F (580 degrees C).

2.3.4.2.8 Flash Ignition Temperature, ASTM D1929: 872 degrees F (466 degrees C).

2.3.4.2.9 Conform with ICBO and BOCA.

2.3.4.2.10 Model Building Codes as a CC-1 rated light transmitting plastic.

2.3.4.3 Physical Properties:

2.3.4.3.1 Gauge/Tolerance: 1.30 inches (33 mm) plus or minus 5 percent.

2.3.4.3.2 Weight: 8.1 lbs per sq ft (39.55 kg per sq m).


2.3.4.3.4 Light Transmittance; Clear: 67 percent.

2.3.4.3.5 Colors Standard: Clear.

2.3.4.3.6 Custom Colors: As determined by the Architect.

** NOTE TO SPECIFIER ** Delete sheet size options not required.






** NOTE TO SPECIFIER ** Bullet-resistant glazing for security applications, 24-hour convenience stores, specialty retailers, banks, government and detention facilities, as well as other cash transaction areas.

2.3.5 Tuffak Polycarbonate, Hygard BR750 sheet. A two-ply polycarbonate and acrylic sheet for security applications requiring UL Listed Level 1 bullet resisting glazing. Abrasion and UV resistant surfaces for extended service life in harsh environments.

2.3.5.1 Ballistics Rating:

2.3.5.1.1 UL752 Level I MPSA 0.354 inch (9 mm).

2.3.5.1.2 H.P. WHITE TP0500.02 Level B Ballistics 0.354 inch (9 mm).

2.3.5.2 Laminate Construction:

2.3.5.2.1 Polycarbonate Sheet: 1/8 inch (3 mm) with high AR abrasion-resistant surface.

2.3.5.2.2 Acrylic Sheet: 1/2 inch (12.7 mm).

2.3.5.2.3 Polycarbonate Sheet: 1/8 inch (3 mm) with high AR abrasion-resistant surface.



2.3.5.3.1 Gauge/Tolerance: .780 inch (19.81 mm) plus or minus 8 percent.



2.3.5.3.4 Percent Light Transmittance: Clear; 88 percent.


2.3.5.3.6 Color: As determined by the Architect.

** NOTE TO SPECIFIER ** Delete sheet sizes not required. Custom Sizes on request.

2.3.5.4 Sheet Sizes: 38 x 96 inches (965 x 2438 mm).





2.3.6 Tuffak Polycarbonate, Hygard CG375 sheet. 2-ply containment grade sheet. 3/8 inches (10 mm) laminate. Resists spalling and white-out after repeated high force impacts,

2.3.6.1 Meets ASTM F 1915 and HP White TP 0500.

2.3.6.2 Exterior surfaces: Proprietary AR Hardcoat that facilitates cleaning and resists marring, chemical attack, and graffiti. Limited Product Warranty: 7 year against coating failure. yellowing, and hazing. The terms of the warranty are available upon request.


2.3.6.3.1 Tuffak AR-I 3/16 inch (4.76 mm) abrasion resistant surface.

2.3.6.3.2 Polyurethane bonding interlayer.

2.3.6.3.3 Tuffak AR-I 3/16 inch (4.76 mm) abrasion resistant surface.





2.3.6.7 Typical Properties:

2.3.6.7.1 Gauge and Tolerance: 0.390 inch (9.91 mm) plus or minus 5 percent.



2.3.6.7.4 U-Value: 0.84.

2.3.6.7.5 Light Transmission: 88 percent. Clear.

2.3.6.8 Force Entry and Containment:

2.3.6.8.1 ASTM F 1233.08 Class 1.4 Contraband Passage, and Class 2.8 Body Passage.

2.3.6.8.2 ASTM F 1913.03 Grade 3.

2.3.6.8.3 HP White TP 0500.03 Level 1 Sequence 13.

2.3.6.9 Agency Information:

2.3.6.9.1 Combustibility Class CACI.

2.3.6.9.2 Miami-Dade NOA 12-0605.05.

** NOTE TO SPECIFIER ** Used primarily in detention facility and jail glazing to meet specific requirements for protection against forced entry/egress into or from controlled areas.

2.3.7 Tuffak Polycarbonate, Hygard CG500 sheet. A three-ply sheet for architectural security glazing. Abrasion and UV resistant hard coated surfaces for extended service life.

2.3.7.1 Force Entry, Ballistics Ratings:

2.3.7.1.1 H.P. WHITE TP 0500.01 Level II Step 12 and Level A Ballistics (.38 Special).

2.3.7.1.2 ASTM F 1233 Class III Step 15.


2.3.7.2.1.1 Polycarbonate Sheet: 1/8 inch (3 mm) with abrasion-resistant surface.

2.3.7.2.1.2 Polycarbonate Sheet: 1/4 inch (6 mm).

2.3.7.2.1.3 Polycarbonate Sheet: 1/8 inch (3 mm) with abrasion-resistant surface.

2.3.7.2.1.4 Polyurethane bonding interlayers.


2.3.7.2.3 High performance abrasion-resistant surfaces.

2.3.7.2.4 Self-Ignition Temperature: 1077 degrees F (580 degrees C).


2.3.7.2.6 Conform with ICBO and BOCA Model Building Codes as a CC-1 rated Approved Light Transmitting Plastic.


2.3.7.3.1 Gauge and Tolerance: 0.530 inches (13.46 mm) plus or minus 5 percent.


2.3.7.3.3 Shading Coefficient: .90 percent.

2.3.7.3.4 Light Transmittance: 83 percent. Clear.




2.3.7.3.7 Sheet Sizes: 38 x 96 inches (965 x 2438 mm).



** NOTE TO SPECIFIER ** For detention facility and jail glazing meeting requirements for protection against forced entry/egress into or from controlled areas.

2.3.8 Tuffak Polycarbonate, Hygard CG750 sheet. A three-ply polycarbonate for architectural security glazing. Abrasion and UV resistant hard coated surfaces.

2.3.8.1 Forced Entry, Ballistics Ratings:

2.3.8.1.1 H.P. WHITE TP 0500.01 Level IV Step .31 and Level B Ballistics (.9 mm).

2.3.8.1.2 ASTM F 1233 Class IV Step 26.


2.3.8.2.1 Polycarbonate Sheet: 1/8 inch (3 mm) with abrasion-resistant surface.

2.3.8.2.2 Polycarbonate Sheet: 1/2 inch (12.7 mm).

2.3.8.2.3 Polycarbonate Sheet: 1/8 inch (3 mm) with abrasion-resistant surface.




2.3.8.3.2 High performance abrasion-resistant surfaces.

2.3.8.3.3 Self-Ignition Temperature: 1077 degrees F (580 degrees C).


2.3.8.3.5 Conform with ICBO and BOCA Model Building Codes as a CC-1 rated Approved Light Transmitting Plastic.


2.3.8.4.1 Gauge/Tolerance .780 inch (19.81 mm) plus or minus 5 percent.

2.3.8.4.2 Weight 4.9 lbs per sq ft (23.9 kg per sq m).

2.3.8.4.3 Shading Coefficient: .87 percent.

2.3.8.4.4 Light Transmittance: 77 percent. Clear.







** NOTE TO SPECIFIER ** Flat and formed sign faces, channel letters, and lighting fixture covers.

2.3.9 Tuffak Polycarbonate, Tuffak LD sheet. Excellent light uniformity without sacrificing light transmission. Proprietary diffuser technology eliminates visible hot spots from pinpoint LED lights in typical flat and formed sign applications. High impact strength and dimensional stability. UV resistance assures long lasting outdoor weathering performance.

2.3.9.1 Limited Product warranty: Ten year limited product warranty against breakage.

2.3.9.2 Regulatory Code Compliance and Certifications:

2.3.9.2.1 UL 879: Electric Sign Components UL File No. E146154.

2.3.9.2.2 UL 94: Flammability UL File No. E351891.




2.3.9.3.2.1 White/B27 at 0.118 inch (3 mm): 27 percent.

2.3.9.3.2.2 White/B48 at 0.118 inch (3 mm): 50 percent.

2.3.9.3.3 Water Absorption, ASTM D570 at 24 hours: 0.15 percent.

** NOTE TO SPECIFIER ** Delete color options not required. Custom colors available upon request.

2.3.9.3.4 Color: White/ B48: 0.093 to 0.236 inches (2.36 to 6 mm).

2.3.9.3.5 Color: White/ B27: 0.093 to 0.236 inches (2.36 to 6 mm).

2.3.9.3.6 Color: Red/ D96: 0.118 to 0.177 inches (3 to 4.5 mm).

2.3.9.3.7 Color: Red/ D99: 0.118 to 0.177 inches (3 to 4.5 mm).

2.3.9.3.8 Color: Blue/ F84: 0.118 to 0.177 inches (3 to 4.5 mm).

2.3.9.3.9 Color: Blue/ F85: 0.118 to 0.177 inches (3 to 4.5 mm).

2.3.9.3.10 Color: Green/ H87: 0.118 to 0.177 inches (3 to 4.5 mm).

2.3.9.3.11 Color: Yellow/ M72: 0.118 to 0.177 inches (3 to 4.5 mm).

2.3.9.3.12 Color: Orange/ C59: 0.118 to 0.177 inches (3 to 4.5 mm).











2.3.9.4.9.1 Notched: 18 ft-lbs per inch (0.96 Nm per mm).

2.3.9.4.9.2 Unnotched: 60 ft-lbs per inch (3.202 Nm per mm). no Failure.





2.3.9.4.14 Rockwell Hardness, ASTM D785: M70 and R118.

2.3.9.4.15 Impact Resistance, ASTM D3763: 47 ft-lbs (63.7 Nm).


2.3.9.5.1 Coefficient of Thermal Expansion, ASTM D696: 0.0000375 in per in per degrees F.


2.3.9.5.3 Heat Deflection Temperature, ASTM D648: At 264 psi (1820 kPa): 270 degrees F (132 degrees C. At 66 psi (455 kPa): 280 degrees F (138 degrees C).







2.3.9.6.5 Dielectric Strength, ASTM D149 in air at .125 inch (3 mm): 380 V/mil.



2.3.9.7.2 Flame Class, UL 94 at 0.093 inch (2.36 mm): V2. At 0.236 (6 mm): V0.

** NOTE TO SPECIFIER ** Typical applications; transparent interior aircraft components, switchgear covers, electrical devices, thermoformed equipment housings, and other current carrying components. Virtually unbreakable with many times the impact strength of float glass and acrylic.

2.3.10 Tuffak Polycarbonate, Tuffak LF UV stable sheet.

2.3.10.1 Sheet Thickness: from .080 inch (2 mm).

2.3.10.2 Standards Compliance: CID A-A-59502. Type II - Flame Resistant, Class 1, UV Stabilized. FAR 25.853 paragraphs A and B.



2.3.10.3.2 Light Transmission, ASTM D1003: Clear; 86 percent.

2.3.10.3.3 Haze, ASTM D1003: Clear; less than 1 percent.

2.3.10.3.4 Flammability, UL 94: V-0.









2.3.10.4.6 Instrumented Impact ASTM D3763: 45 ft-lbs (61 Nm).



2.3.10.5.2 Heat Deflection Temperature, ASTM D648: At 264 psi (1820 kPa): 270 degrees F (132 degrees C. At 66 psi (455 kPa): 280 degrees F (138 degrees C).

** NOTE TO SPECIFIER ** Interior LED and conventional lighting fixtures.

2.3.11 Tuffak Polycarbonate, Tuffak Lumen XT sheet. Translucent with a textured surface on one side designed for lighting lenses. A combination of high light diffusion and high light transmission due to an optimized surface texture and advanced diffuser technology.



2.3.11.1.2 Water Absorption at 24 hrs, ASTM D570: 0.15 percent.



2.3.11.1.4.1 LC3 at 0.118 inch (3.00 mm) 85 percent.



2.3.11.1.4.4 LW3 at 0.118 inch (3.00 mm) 90 percent.




2.3.11.2.1 Tensile Strength, Ultimate ASTM D792: 1.2.

2.3.11.2.2 Tensile Strength, Yield ASTM D570: 0.15 percent.

2.3.11.2.3 Tensile Modulus ASTM E132: 0.38.


2.3.11.2.5 Flexural Strength, ASTM D1003: 85 percent.

2.3.11.2.6 Flexural Modulus, ASTM D1003: 85 percent.

2.3.11.2.7 Instrumented Impact, ASTM D1003: 85 percent.




2.3.11.3.3 Heat Deflection Temperature, ASTM D648: At 264 psi (1820 kPa): 274 degrees F (134 degrees C). At 66 psi (455 kPa): 287 degrees F (142 degrees C).

2.3.11.4 Electrical:

2.3.11.4.1 Dielectric Constant at 10 Hz, ASTM D150: 2.98.

2.3.11.4.2 Dielectric Constant at 60 Hz, ASTM D150: 2.88.


2.3.11.4.4 Dissipation Factor at 60 Hz, ASTM D150: 0.002.

2.3.11.4.5 Arc Resistance, ASTM D495: Tungsten Electrodes: 125 seconds.


2.3.11.5 Flammability: Material thickness of 0.060 to 0.118 inch (1.5 to 3 mm).

2.3.11.5.1 Flame Class, UL 94: V2.

2.3.11.5.2 Surface Flammability, ASTM E162: Less than 100.

2.3.11.5.3 Smoke Density, ASTM E662: At 1.5 min: Less than 100. At 4 min: Less than 200. At 20 min: Less than 200.

2.3.11.5.4 Vertical Burn; at 12 sec, FAR 25.853: Pass.

2.3.11.5.5 Horizontal Burn, 2.5 and 4.0 inch (64 and 102 mm), FAR 25.853: Pass.

2.3.11.5.6 Toxic Gas Generation at 0.060 to 0.118 inch (1.5 to 3 mm), BSS 7239 and SMP 800-C: Pass.

2.3.11.6 Diffusion and Transmission:

2.3.11.6.1 Lumen XT Grade: LC3. Diffusion, FWHM: 38 to 53 degrees.

2.3.11.6.1.1 Transmission, ASTM D1003: 85 to 90 percent.

2.3.11.6.2 Lumen XT Grade: LC5. Diffusion, FWHM: 53 to 77 degrees

2.3.11.6.2.1 Transmission, ASTM D003: 77 to 88 percent

2.3.11.6.3 Lumen XT Grade: LC7. Diffusion, FWHM: 86 to 135 degrees


2.3.11.6.4 Lumen XT Grade: LW3. Diffusion, FWHM: 38 to 53 degrees


2.3.11.6.5 Lumen XT Grade: LW5. Diffusion, FWHM: 53 to 77 degrees


2.3.11.6.6 Lumen XT Grade: LW7. Diffusion; FWHM: 86 to 135 degrees


** NOTE TO SPECIFIER ** Marine flexible enclosures, tent and awning enclosures

2.3.12 Tuffak Polycarbonate, Tuffak Marine 5 sheet. For applications of high optical clarity, exceptional durability, and longevity in harsh marine environment.

2.3.12.1 Low optical distortion and sight lines. Abrasion resistance, enhanced clarity, chemical resistant. Long lasting outdoor weathering performance. High impact strength at temperatures down to minus 30 degrees F (minus 43.3 degrees C). Easily cut and sewn. Does not require gluing.Limited Product Warranty: Five year against micro-cracking, yellowing, and breakage.Physical Properties:


2.3.12.1.2 Light Transmission, ASTM D1003: Clear at 0.060 inch (1.5 mm) 90 percent.

2.3.12.1.3 Light Transmission, ASTM D1003: Clear at 0.080 inch (2.0 mm) 89 percent.

2.3.12.1.4 Chemical Resistance, ANSI Z26.1: Pass.

2.3.12.1.5 Taber Abrasion, 100 Cycles, Delta Haze, ASTM D1044: 2 percent.

2.3.12.1.6 Impact resistance, ASTM D3763: 47.

2.3.12.1.7 Abrasion Resistance: 2, Delta Haze Percentage.



2.3.12.2.2 Modulus of Elasticity, ASTM D 638: 340,000 psi (2344217 kPa).






2.3.12.2.6 Instrumented Impact at 0.60 inch (15 mm) ASTM D3763: 21 ft-lbs (28.5 Nm).



2.3.12.2.9 Instrumented Impact at 0.125 inch (3 mm) at minus 30 degrees F (minus 34.4 degrees C), ASTM D3763: 50 ft-lbs (67.8 Nm).


2.3.12.2.11 Rockwell Hardness ASTM D785: M70 and R118.

2.3.12.2.12 Chemical Resistance, ASTM D1308. Greater than 24 hours.

2.3.12.2.12.1 Acetone, Antifreeze (50/50), Benzene, Bleach (Clorox concentrated), Denatured Alcohol, Di (2-ethylhexyl) phthalate, Diesel Oil, Isopropyl Alcohol (IPA), Kerosene, Methyl Alcohol, Methyl Butyl Ketone, Methyl Ethyl Ketone, Methylene Chloride, Naphthalene, 1-bromo, Potassium Hydroxide - Lye (10 percent), Sodium Hydroxide (10 percent), Toluene, Turpentine, Unleaded Gasoline (87 Octane), Vinegar, Xylene, Hydrochloric Acid (20 percent), and Sulfuric Acid (20 percent).


2.3.12.3.1 Coefficient of Thermal Expansion, ASTM D696: 0.0000375 inch per inch per degrees F.

2.3.12.3.2 Heat Deflection Temperature, ASTM D648: At 66 psi (455 kPa): 280 degrees F.

** NOTE TO SPECIFIER ** For use where clarity and impact strength is essential. Applications include sight glasses, manifolds, insulators, and diaphragms.

2.3.13 Tuffak Polycarbonate, Tuffak MG Sheet. Machine Grade polycarbonate engineering plate. An amorphous thermoplastic, extremely high impact, high elasticity modulus, dimensionally stabile, and good mechanical and electrical properties.

2.3.13.1 Standards Compliance: CID A-A-59502. Type 1, Class 1, UV Stabilized.




2.3.13.2.3 Water Absorption, Equilibrium, at 24 hours, ASTM D570: 0.15 percent.










2.3.13.3.9 Poisson's Ratio: 0.38.










2.3.13.5.2 Volume Resistivity ASTM D257: 8.2 x 10E16 Ohm-cm.


2.3.13.5.4 Dissipation Factor, ASTM D150 at 1 MHz: 0.01.

2.3.13.5.5 Arc Resistance, ASTM D495: Stainless Steel Strip electrode: 10 to 11 seconds. Tungsten Electrodes: 120 seconds.


2.3.13.6 Flammability: Flame Class, UL 94, greater or equal to 0.375 inch (9.52 mm): V0.

** NOTE TO SPECIFIER ** Recreational vehicle windscreens, face shields, laminates.

2.3.14 Tuffak Polycarbonate, Tuffak OP. Lightweight thermoformable sheet. Polished surface, UV stabilized, transparent polycarbonate product. For applications requiring improved optical quality. High impact strength, dimensional stability, temperature resistance, and clarity.

2.3.14.1 Limited Product Warranty: Five year against breakage.





2.3.14.3.3 Light Transmission:

2.3.14.3.3.1 Clear at 0.118 inch (3 mm), ASTM D1003: 86 percent.

2.3.14.3.3.2 Gray /I30 at 0.118 inch (3 mm), ASTM D1003: 50 percent.

2.3.14.3.3.3 Bronze /K09 at 0.118 inch (3 mm), ASTM D1003: 50 percent.

2.3.14.3.3.4 Dark Gray /I35 at 0.118 inch (3 mm), ASTM D1003: 18 percent.

2.3.14.3.4 Water Absorption at 24 hours, ASTM D570: 0.15 percent.


2.3.14.3.6 Impact Resistance, ASTM D3763: 46.























2.3.14.5.5 Shading Coefficient, NFRC 100 at 0.236 inch (6 mm) Thick: Clear; 0.97. Gray or Bronze; 0.77.

2.3.14.5.6 U factor, NFRC 100 at 0.236 inch (6 mm):



2.3.14.5.7 U factor, NFRC 100 at 0.375 inch (9.5 mm):



** NOTE TO SPECIFIER ** Formed for flat signage, polished sign face surface or matte..

2.3.14.6 Tuffak Polycarbonate, Tuffak Sign Matte. Clear polycarbonate, for sign faces.

2.3.14.7 Limited Product Warranty: Five year against breakage.


2.3.14.8.1 Specific Gravity ASTM D792: 1.2.

2.3.14.8.2 Refractive Index, ASTM D542 at 72 degrees F (22.2 degrees C): 1.586.

2.3.14.8.3 Light Transmission, ASTM D1003, Clear 1/8 inch (3 mm): 86 percent.

2.3.14.8.4 Light Transmission, ASTM D1003, Gray/Bronze: 50 percent.

2.3.14.8.5 Light Transmission, ASTM D1003, Dark Gray: 18 percent.


2.3.14.8.7 Water Absorption, Equilibrium after 24 hrs, ASTM D570: 0.15 percent.

2.3.14.8.8 Surface Finish: Polished or Matte.










2.3.14.9.9 Poisson's Ratio: 0.38.




2.3.14.9.11 Instrumented Impact, ASTM D3763 at 1/8 inch (3 mm): 45 ft-lbs (61.01 Nm).





2.3.14.10.1 Coefficient of Thermal Expansion, ASTM D696: 0.0000375 in per in per degrees F




2.3.14.10.5 Shading Coefficient, ASHRAE at 1/8 inch (3 mm): Clear: 1.02. Gray: 0.7. Bronze: 0.7.

2.3.14.10.6 U Value at 1/4 inch (6 mm) thick: Summer Gain: 0.90. Winter Loss: 0.96.




2.3.14.11.3 Dissipation Factor, ASTM D150 at 60 Hz: 0.0009. At 1 MHz: 0.01.

2.3.14.11.4 Arc Resistance, ASTM D495: Stainless Steel Strip electrode: 10 to 11 seconds. Tungsten Electrodes: 120 seconds.

2.3.14.11.5 Dielectric Strength, ASTM D149 in air at .125 inch (3 mm): 380 V/mil.



2.3.14.12.2 Ignition Temperature, ASTM D1929: Self: 1070 degrees F (576.7 degrees C). Flash: 870 degrees F (456.5 degrees C).

2.3.14.12.3 Flame Class, UL 94 at 0.060 inch (1.52 mm): V2. At 0.236 (6 mm): V0.

** NOTE TO SPECIFIER ** Flat and formed sign faces and channel letters.

2.3.15 Tuffak Polycarbonate, Tuffak SL sheet. Sign Grade sheet is a lightweight thermoformable polycarbonate sheet or reel product with advanced UV resistance. High clarity, long lasting weathering performance, high impact strength, dimensionally stabile, and high temperature resistance.

2.3.15.1 Standards Compliance: CID A-A-59502. Type IV, Coated Sheet with UV Resistance, Class 1 - Monolithic. UL 879 standard for electric sign components.

** NOTE TO SPECIFIER ** Delete color option not required. Any color can be matched upon request.

2.3.15.2 Color: Clear.

2.3.15.3 Color: As determined by the Architect.

2.3.15.4 Limited Product Warranty: 10 year for breakage resistance.

2.3.15.5 Impact Resistance, ASTM D3763: 46.





2.3.15.6.3.1 At 0.118 inch (3 mm): Clear: 86 percent. B59 White: 27 percent.

2.3.15.6.3.2 At 0.150 and 0.177 inch (3.81 and 4.48 mm): B54 White: 27 percent.

2.3.15.6.4 Water Absorption, Equilibrium, at 24 hours, ASTM D570: 0.15 percent.


** NOTE TO SPECIFIER ** Delete color and thickness options not required.

2.3.15.6.6 Color: Clear/ A00: 0.093 to 0.236 inches (2.36 to 6.00 mm).

2.3.15.6.7 Color: White/ B59: 0.093 to 0.118 inches (2.36 to 3.00 mm).

2.3.15.6.8 Color: White/ B54: 0.150 to 0.236 inches (3.81 to 6.00 mm).

2.3.15.6.9 Color: Red/ D92: 0.118 to 0.177 inches (3.00 to 4.50 mm.

























2.3.15.9.2 Volume Resistivity ASTM D257 Ohm-cm 8.2 x 1016.



2.3.15.9.5 Dielectric Strength, ASTM D149 in air at 0.125 inch (3 mm): 380 V/mil


2.3.15.10.1 Horizontal Burn, AEB, ASTM D635: Less than 1 inch 9(25 mm).

2.3.15.10.2 Flame Class, UL 94 at 0.060 inch (1.5 mm): HB.

2.3.15.10.3 Ignition Temperature, ASTM D1929: Self: 1022 degrees F (550 degrees C). Flash: 824 degrees F (440 degrees C).

** NOTE TO SPECIFIER ** Sight windows for tanks/vessels, viewport windows, medical parts and military applications.

2.3.16 Tuffak Polycarbonate, Tuffak WG sheet. High impact strength, elasticity modulus, and dimensional stability. Good mechanical and electrical properties. Low levels of impurities.




2.3.16.2.2 Water Absorption after 24 hrs, ASTM D570: 0.15 percent.











2.3.16.3.9 Shear Strength at Yield, ASTM D732: 6,000 psi (41368 kPa).



2.3.16.3.12 Rockwell Hardness, ASTM D785: M70, and R118.




2.3.16.4.3 Heat Deflection Temperature, ASTM D648: At 264 psi (1820 kPa): 270 degrees F. At 66 psi (455 kPa): 280 degrees F.



2.3.16.5.1 Dielectric Constant at 10 Hz ASTM D150: 2.96.

2.3.16.5.2 Dielectric Constant at 60 Hz ASTM D150: 3.17.

2.3.16.5.3 Volume Resistivity ASTM D257: 8.2 x 1016Ohm-cm.

2.3.16.5.4 Dissipation Factor at 60 Hz, ASTM D150: 0.

2.3.16.5.5 Dielectric Strength, in air at 0.125 inch (3 mm), ASTM D149: 380 V/mil.

2.3.16.6 Optical Properties: Haze, ASTM D1746: 1.0 percent.

2.3.16.7 Flammability Properties:

2.3.16.7.1 Flame Class, UL 94 at 0.75 to 2.00 inch (19 to 51 mm): VO.

** NOTE TO SPECIFIER ** Marine flexible enclosures, tent and awning enclosures.

2.3.16.8 Tuffak Polycarbonate, Tuffak VR rollable sheet. High optical quality, exceptional durability, weathering, and UV resistant. Low optical distortion. Cut and sewn seams. A high clarity, wrinkle-free alternative to flexible vinyl. Impact strength maintained to minus 30 degrees F (minus 43.4 degrees C).

2.3.16.9 Limited Product Warranty: 5 year against breakage.


2.3.16.10.1 Specific Gravity, ASTM D 792: 1.2.

2.3.16.10.2 Light Transmission, ASTM D1003, at 0.040 inch (1 mm) thick, Clear: 90 percent.

2.3.16.10.3 Impact Resistance, ASTM D3763: 47 ft-lbs (63.7 Nm).






2.3.16.11.3 Instrumented Impact at 0.125 inch (3 mm) at minus 30 degrees F (minus 34.4 degrees C), ASTM D3763: 50 ft-lbs (67.8 Nm).

2.3.16.11.4 Poisson's Ratio ASTM E132: 0.38.

2.3.16.11.5 Rockwell Hardness ASTM D785: M70 and R118.




2.4 MULTIWALL POLYCARBONATE SHEETS

2.4.1 Basis of Design: Gallina Multiwall Polycarbonate.

** NOTE TO SPECIFIER ** Delete wall system options not required.

2.4.1.1 Two-Wall Systems: PolyCarb as supplied by A and C Plastics.

2.4.1.1.1 Thickness: 5/32 inch (4 mm). Weight: 0.164 lbs per sq ft (0.80 kg per sq m).

2.4.1.1.1.1 Standards Compliance: ASTM E84 Class A.

2.4.1.1.1.2 Bend Radius, Minimum: 30 inches (762 mm).

2.4.1.1.1.3 U-Value: 0.68.

2.4.1.1.1.4 Clear: Visible Light Transmission: 85.

2.4.1.1.1.4.1 Solar Heat Gain Coefficient: 0.83.

2.4.1.1.1.4.2 Shading Coefficient: 0.95.

2.4.1.1.1.5 Bronze: Visible Light Transmission: 57.



2.4.1.1.1.6 Opal: Visible Light Transmission: 58.




2.4.1.1.2.1 Standards Compliance: ASTM E84 Class A, ASTM D635 Class CCI.


2.4.1.1.2.3 U-Value: 0.61.










2.4.1.1.2.7 Blue: Visible Light Transmission: 53.



2.4.1.1.2.8 Green: Visible Light Transmission: 54.






2.4.1.1.3.3 U-Value: 0.58.


2.4.1.1.3.4.1 Solar Heat Gain Coefficient 0.82.

















2.4.1.1.4.3 U-Value: 0.52.













2.4.1.1.4.8 Green: Visible Light Transmission: .54.



2.4.1.2 Three-Wall Systems: PolyCarb as supplied by A and C Plastics.



2.4.1.2.1.2 U-Value: 0.52.




2.4.1.2.2 Thickness: 3/8 inch (10 mm). Weight: 0.430 lbs per sq ft (2.10 kg per sq ft).


2.4.1.2.2.2 U-Value: 0.47.


2.4.1.2.2.3.1 Solar Heat Gain Coefficient: 075.











2.4.1.2.3.3 U-Value: 0.40.
















2.4.1.2.4 Thickness: 1 inch (25 mm). Weight: 0.665 lbs per sq ft (3.25 kg per sq m).



2.4.1.2.4.3 U-Value: 0.34.








2.4.1.3 Five-Wall RDC Systems: PolyCarb as supplied by A and C Plastics.


2.4.1.3.1.1 Standards Compliance: ASTM E84 Class A, ASTM D635 Class CC1.


2.4.1.3.1.3 U-Value: 0.36.










2.4.1.4 Six-Wall Systems: PolyCarb as supplied by A and C Plastics.



2.4.1.4.1.2 U-Value: 0.32.







2.4.1.5 Seven-Wall Systems: PolyCarb as supplied by A and C Plastics.

2.4.1.5.1 Thickness: 1 inch (25 mm). Weight: 0.717 lbs per sq ft (3.50 kg per sq m).

2.4.1.5.1.1 Standards Compliance: ASTM E84 Class A, ASTM D635 Class CC1.

2.4.1.5.1.2 Bend Radius: Do not bend.

2.4.1.5.1.3 U-Value: 0.26.







2.4.1.5.2 Thickness: 1-9/16 inch (40 mm). Weight: 0.799 lbs per sq ft (3.90 kg per sq m).

2.4.1.5.2.1 Standards Compliance: ASTM D635 Class CC1.


2.4.1.5.2.3 U-Value: 0.19.







2.4.1.6 Eleven-Wall Systems: PolyCarb as supplied by A and C Plastics.

2.4.1.6.1 Thickness: 1 inch (25 mm) Weight: 0.696 lbs per sq ft (3.40 kg per sq m).



2.4.1.6.1.3 U-Value: 0.23.







2.4.1.6.2 Thickness: 1-1/4 inch (32 mm). Weight: 0.758 lbs per sq ft (3.70 kg per sq m).



2.4.1.6.2.3 U-Value: 0.19.







2.4.1.7 PolyCarb Accessories:

** NOTE TO SPECIFIER ** Delete accessories if not required.

2.4.1.7.1 PC Corner R Profile: 5/16, 3/8, 5/8 inch (8, 10, 16 mm).

2.4.1.7.2 PC Corner F Profile: 5/16, 3/8, 5/8 inch (8, 10, 16 mm).

2.4.1.7.3 PC Connector H Profile: 5/16, 3/8, 5/8, 3/4, 1 inch (8, 10, 16, 20, 25 mm).

2.4.1.7.4 Aluminum U Profile: 5/16, 3/8, 5/8 inch (8, 10, 16 mm).

2.4.1.7.5 PC U Profile: 5/16, 3/8, 5/8, 1 inch (8, 10, 16, 25 mm).

2.4.1.7.6 PC Snap H Connector Profile: 7/32, 3/8 (6, 10 mm).

2.4.1.7.7 Washers with gaskets. Bubble washers. Neoprene washers.

2.4.2 Basis of Design: ArcoPlus Modular Systems as supplied by A and C Plastics.

2.4.2.1 Optional Treatments:

** NOTE TO SPECIFIER ** Delete coating options not required.

2.4.2.1.1 Coating: IR. Reducing the interior solar heat gain coefficient by 20 percent.

2.4.2.1.2 Coating: UV. 1-sided. Protection with a matte finish.

2.4.2.1.3 Coating: UV. 2-sided. Protection with a matte finish.


2.4.2.1.5 Three-Wall Modular System No. 613. Thickness: 0.394 inches (10 mm). Width: 23.82 inch (605 mm).

2.4.2.1.6 Bend Radius, Minimum: Do not bend.


2.4.2.1.8 U-Factor: 0.475.

2.4.2.1.9 UV Protection: None.

2.4.2.1.10 Clear: Visible Light Transmission: 76.

2.4.2.1.10.1 Solar Heat Gain Coefficient: 0.81.

2.4.2.1.11 Opal: Visible Light Transmission: 58.

2.4.2.1.11.1 Solar Heat Gain Coefficient: 0.65.

** NOTE TO SPECIFIER ** Delete multiwall modular systems options not required.

2.4.2.2 Four-Wall Modular System No. 324:

2.4.2.2.1 Standards Compliance: ASTM E84 Class B, ASTM D635 Class CC1.

2.4.2.2.2 Thickness: 0.787 inches (20 mm). Width: 13.11 inch (3

ARCAT, Inc. · Web viewFalling Dart Impact per ANZI/SAE Z26.1 Dart; Single Impact Vertical Drop,...

Documents

Transcript of ARCAT, Inc. · Web viewFalling Dart Impact per ANZI/SAE Z26.1 Dart; Single Impact Vertical Drop,...