APTDC – RFP FOR PROCUREMENT OF HOUSE BOATSAPTDC – RFP FOR PROCUREMENT OF HOUSE BOATS Page 5 of...

APTDC – RFP FOR PROCUREMENT OF HOUSE BOATS

of 52

DISCLAIMER

This Tender Document for “Procurement of House Boats for APTDC” contains brief information about the

Organization & its activities, Requirements & Specifications of House Boats, the Qualification

Requirements and the Selection process for the successful Bidder. The purpose of this tender document is

to provide Bidders with information to assist the formulation of their bid application (the ‘Application’).

The information contained in this tender Document or subsequently provided to Interested parties (the

“Bidder(s)”), in writing by or on behalf of Andhra Pradesh Tourism Development Corporation Limited (APTDCL) is provided to the Bidder(s) on the terms and conditions set out in the tender documents and any other terms and conditions subject to which such information is provided.

This tender Document does not purport to contain all the information that each Bidder may require. This

tender Document has been prepared with a view to provide the relevant information about the House

Boat requirements & specifications for APTDCL and has not been prepared keeping in mind the investment

objectives, financial situation and particular needs of each Bidder. The APTDCL advises the Bidders to

conduct their own investigations and analysis and satisfy themselves of the accuracy, reliability and

completeness of the information in this tender Document and to obtain independent advice from

appropriate sources. The APTDCL, its employees and advisors make no representation or warranty and

shall not be liable in any manner whatsoever as to the accuracy reliability or completeness of the

information provided in this tender Document.

This tender may not be appropriate for all persons, and it is not possible for APTDCL, its employees or

advisors to consider the investment objectives, financial situation and particular needs of each party who

reads or uses this tender. The assumptions, assessments, statements and information contained in the

Bidding Documents may not be complete, accurate, adequate or correct. Each Bidder should, therefore,

conduct his/her own investigations and analysis and should check the accuracy, adequacy, correctness,

reliability and completeness of the assumptions, assessments, statements and information contained in

this tender and obtain independent advice from appropriate sources.

Information provided in this tender document to the Bidder(s) is on a wide range of matters, some of

which may depend upon interpretation of law. The information given is not intended to be an exhaustive

account of statutory requirements and should not be regarded as a complete or authoritative statement

of law. APTDCL accepts no responsibility for the accuracy or otherwise for any interpretation or opinion on

law expressed herein.

Intimation of discrepancies in the tender Document, if any, may be given, by the Bidders, to the office of the APTDCL immediately. If APTDCL receives no written communication, it shall be deemed that the Bidders are satisfied with the information provided in the tender document.

This tender Document is not an agreement and is not an offer or invitation by APTDCL to any other party.

The terms on which the house boats shall be purchased and the right of the successful Bidder, shall be as

set out in separate agreements executed between APTDCL and the successful Bidder in the format broadly

set out herein. APTDCL may in its absolute discretion, but without being under any obligation to do so,

update, amend or supplement the information, assessment or assumptions contained in this tender

document.


of 52

APTDCL, its employees and advisors make no representation or warranty and shall have no liability to any

person, including any Applicant or Bidder under any law, statute, rules or regulations or tort, principles of

restitution or unjust enrichment or otherwise for any loss, damages, cost or expense which may arise from

or be incurred or suffered on account of anything contained in this tender document or otherwise,

including the accuracy, adequacy, correctness, completeness or reliability of the tender document and any

assessment, assumption, statement or information contained therein or deemed to form part of this

tender document or arising in any way for participation in this Bid Stage

APTDCL also accepts no liability of any nature whether resulting from negligence or otherwise howsoever

caused arising from reliance of any Bidder upon the statements contained in this tender document.

APTDCL may in its absolute discretion, but without being under any obligation to do so, update, amend or

supplement the information, assessment or assumptions contained in this tender document. APTDCL

reserves the right to accept or reject any or all Applications without giving any reasons thereof. APTDCL

will not entertain or be liable for any claim for costs and expenses in relation to the preparation of the

documents to be submitted in terms of this tender Document.

The Bidder shall bear all its costs associated with or relating to the preparation and submission of its Bid.

All such costs and expenses will remain with the Bidder and APTDCL shall not be liable in any manner

whatsoever for the same or for any other costs or other expenses incurred by a Bidder in preparation or

submission of the Bid, regardless of the conduct or outcome of the Bidding Process. The word “Bid” and

“Tender” is used interchangeably in the document.


of 52

SECTION 1

PROJECT BACKGROUND

1. PROJECT BACKGROUND

1.1. Introduction

1.1.1 Andhra Pradesh Tourism Development Corporation Limited is a government of Andhra Pradesh

Undertaking functioning under the Tourism Department, Government of Andhra Pradesh, aimed at

promoting and managing tourist destinations and packages, to facilitate tourist’s inflow from all over India

and abroad.

1.1.2 As part of its existing mandate, Andhra Pradesh Tourism Development Corporation Limited (APTDC) has also undertaken additional infrastructure development to offer different services which gives sustainable additional revenue to the corporation, and on the other hand it also provides incentive for private sector Hotels. Through this tender APTDC intends, to select a ‘Marine Fabricator’ for the Procurement of House Boats to deploy in the backwaters/freshwater/saline water of the following places as mentioned in the document.

1.1.3 This Project is envisaged to diversify the tourism services offered by the Corporation to

supplement its revenue and to provide additional entertainment option to the tourists visiting this

state. An information document covering details of the instant proposal may be downloaded from the

website www.aptdc.gov.in.

1.1.4 APTDC Ltd. intends to procure One (01) number of Maintenance free House Boats which are to be deployed at different locations of Back waters/Fresh waters/saline water of Andhra Pradesh. The details are at Vijayawada...

· One double bedded room (Attached bath & Toilet) House Boats with facilities for driver cabin,

pantry attendant room and per the standard design mentioned in the document ---- 1 No.

1.1.5 The work will be awarded to the successful Bidder on the basis of the rate quoted by them (subject to Bidder fulfilling the Eligibility Criteria, as laid down in this tender document)


of 52

SECTION 2

NOTICE INVITING BID

2.0 Notice Inviting Bids

2.1 APTDC Ltd. intends to procure One (01) no. of Maintenance free House Boats which are to be deployed at different locations of Back waters/Lake/River of Andhra Pradesh details of which are given below.

Sl. No. Particulars/Description Quantity Location

01 One double bedded room (Attached bath & Toilet) with

dining/Mini conference House Boats with facilities for driver

cabin, pantry attendant room ate as per the standard design

1 Nos. Tatipudi,

Vijayanagaram

Dist.

2.2 APTDC invites online Bids from any reputed House Boat fabricators for Drawing & Design,

Development, Fabrication and Delivery of the House Boats. The selected Bidder should Submit/obtain drawing & design approval, fabrication related necessary clearances and approvals from the

Government agencies/departments on their own and the fabrication shall have be done under the

supervision of the Agency/ officer deputed by APTDCL

2.3 Deemed Knowledge and Disclaimer:-

2.3.1 APTDCL shall receive offline Bids pursuant to this tender document, in accordance with the terms

set forth herein as modified, altered, amended and clarified from time to time by APTDCL. Bidders shall

submit bids in accordance with such terms on or before the Proposal Due Date. The participating

Bidders are expected to ascertain on its own responsibility, information, technical data, traffic data,

market study, etc. on his own.

2.3.2 The Bidder hereby admits, agrees and acknowledges that APTDCL has not made any representation to the Bidder or given any warranty of any nature whatsoever in respect of the instant proposal of purchasing house boats including in respect of its usefulness, utility etc. or the fulfillment of criteria or conditions for obtaining Applicable Permits by the Bidder for the Proposal.

2.4 Salient features of bidding Process:

a) APTDCL has adopted offline bidding process for declaration of a Selected Bidder for each schedule to grant rights under the Lease Agreement for the Leased Space. b) The details of bidding process are provided in Section 3. c) Schedule of bidding process for RFP:


of 52

01.10.2018

Publishing date

Pre bid meeting (All the bidders are requested to

attend the pre bid meeting) 08.10.2018 3:00 PM

Cost of Tender Document (Non refundable) Rs.15,000/-

Last Date & Time of submission of sealed bids 19.10.2018 -15.00 Hrs,

(Proposal due date)

Date & Time of opening of bids 19.10.2018 (As per the decision of the tender committee)

Mail id/Phone [email protected] /[email protected] 0866-2552969

Authority and place for submission of bid

The Superintending Engineer/Chief Engineer

APTDC Ltd.,

document cost and seeking clarifications 5th

floor, Stalin Corporate

Vijayawada 520007


of 52

SECTION 3

REGULATION OF BIDS AND LEASE AGREEMENT 3.1 GENERAL 3.1.1 APTDCL invites online Bids from eligible Bidders in terms of eligibility criteria as specified in this document to procure One (01) no of Maintenance free House Boats. 3.1.2 The information submitted in the tender document will form the basis for evaluating the Bidders. The Bidders may participate in the Bid process as per the instructions given in this tender document 3.1.3 From amongst the Bidders fulfilling the Eligibility Criteria, as laid down in this tender document, the tender shall be awarded to the Selected Bidder on the basis of the lowest rate quoted by the Selected Bidder. 3.1.4 The intending Bidder must read the terms and conditions carefully. 3.1.5 Information and instructions for tenderers posted on website shall form part of tender documents

3.1.6 The tender document can be seen and downloaded from website www.aptdc.gov.in 3.1.7 Tender Document can only be submitted along with technical bid and is mandatory documents

towards cost of Bid Documents such as Demand Draft drawn in the name of “APTDC Limited” payable at

Vijayawada and towards Tender Security such Demand Draft/Bank Guarantee drawn in the name of

“APTDC Limited” payable at Vijayawada and other documents as stated under Clause 3.15 of tender

Document. 3.1.8 Tenderer must ensure to quote rate both in words and figures in financial proposal including taxes

(The tax component must be shown separately but must be inclusive).

3.2 Downloaded Tender Documents: 3.2.1 The complete bid document can be downloaded from the website of www.aptdc.gov.in The Demand

draft towards cost of bidding fees for Rs. 15,000/- and Demand draft towards Bid Security of Rs. 1,00,000/-

must be submitted along with the technical bid for evaluation before the opening of the bids failing which

the bid shall be rejected out rightly. However, the bidder must pay balance EMD at the time of agreement

totaling to 2.5% of the quoted value/order value. No tampering, alteration or changing of the contents of

the Bid documents is permissible. The APTDCL shall not be responsible for any printing error while

downloading the documents.

3.3 Queries in Tender Documents and Amendments 3.3.1. Bidders may send their queries, if any, to SE and CE, APTDCL in writing/mail not later than the date

specified under the bid schedule of Section-II of tender documents (Mail ids [email protected] and [email protected]

). APTDCL shall Endeavour to provide clarifications and such further information as it may, in its sole

discretion, consider appropriate for facilitating a fair, transparent and competitive bidding process,

however, no queries received after prescribed date shall be entertained by the APTDCL. 3.3.2 At any time prior to the Proposal Due Date, the APTDCL may, for any reason whatsoever, whether

at its own initiative or in response to clarifications requested by a bidder, modify the tender document

through the issuance of an addendum/corrigendum. This shall be uploaded on the website stated in 3.1.6

and shall be binding upon all the bidders. 3.3.3 In order to give the Bidders reasonable time to take an addendum into account, or for any other reason, the APTDCL may, at its discretion, extend the Proposal Due Date. 3.3.4 The Response to queries/ addendums (if any) will be uploaded on www.aptdc.gov.in and the Bidders are advised to keep a regular check on the website for any such updates.

3.4 Pre-bid Meeting 3.4.1 Participating Pre-Bid meeting is optional.


of 52

3.4.2 APTDCL shall conduct a pre-bid meeting on the date and location specified under the bid schedule of Section-II of tender document for the purpose of providing clarification and answering the queries of the prospective Bidders. 3.4.3 The tenderer is requested to submit any question in writing or by facsimile, to reach APTDCL not later than the last date of seeking clarification as mentioned in key details of NIT. 3.4.4 Any modification of the Tender Documents, which may become necessary as a result of the Pre-Tender meeting, shall be made by the APTDCL exclusively through the issue of an Addendum/ corrigendum pursuant to Clause 3.3 above. 3.4.5 The intending bidders has to submit the detail drawings including profile, plan, section etc, for scrutiny by the technical team at the time of pre-bid meeting . Approved drawings will be uploaded on the website as an addendum and the bidders shall have to quote rate in his financial bid as per the approved design, diagram uploaded in the website.

3.5 ELIGIBILITY CRITERIA

Only reputed firms having sufficient experience in fabricating House Boats are eligible to participate in the tender

The Bidder shall meet the following minimum Eligibility Criteria (the “Eligibility Criteria”):

3.5.1 A Bidder must have:

• Five years experience in House Boat fabrication

• Executed similar nature of works to the tune of at least 100 lakhs on an continuously for the past three years

• IT, VAT, GST registration/Clearance for the past three years

• Firm registration certificate

• Τurnover of Rs. 100 lakhs on an average for the last three financial years

For the purpose of evaluation of bidder’s qualifications, documents in support of the following details must be submitted

Statement -I

Details of building of house boats and magnitude carried out (Purchase order copies/ Agreement to be enclosed/Completion certificates/Satisfactory certificate/Appreciation letter) along with documentary evidence of satisfactory performance. The tenderer shall have necessary infrastructure required for building house boats under stability and inclination test need to be carried out by any recognized approved agency.

Statement-II

Details of works tendered and work on hand with value of work.

Statement -III

Details of Yard, Machinery, Tools, & Moulds, Space for construction available with the tenderer for use in this work

Statement -IV

Details of Naval Architects and other technical personnel of the tenderer along with names, Educational qualifications and experience

Statement-V

General arrangement drawings must be enclosed for guidance

Statement-VI


of 52

Proofs of GST/VAT registration, Yard facilities, Firm registration, latest Income tax clearance certificate at least for the past three years must be enclosed

Statement-VII

Financial statements of the company as well as letter from the banks regarding credentials of the bidder. Bank solvency is required to produce for minimum 100 lakhs. The builder must submit the business turnover particulars of last 3 years.

3.5.2 Consortiums are not allowed. 3.5.3 The minimum average annual turnover of a Bidder should be Rs 1,00,00,000/- (Rs. One Crore Only) for the preceding three financial years as per the audited balance sheets of the Bidders. The financial data in the prescribed format shall be certified by Chartered Accountant with his stamp and signature in original. In case audited balance sheet of the last financial year is not made available by the bidder, he has to submit an affidavit certifying that ‘the balance sheet has actually not been audited so far’. In such a case the financial data of previous ‘2’ audited financial years will be taken into consideration for evaluation. If audited balance sheet of any year other than the last year is not submitted, the tender may be considered as nonresponsive.

3.6. LANGUAGE AND CURRENCY

3.6.1 The Bid and all the related correspondence and documents shall be written in English language only. 3.6.2 The currency for the purpose of the Bid shall be the Indian National Rupee (INR).

3.7. TENDER SECURITY

3.7.1 The successful Tenderer shall submit a Tender Security for Rs 1,00,000/- (Rupees One lakh only) as hard copy in shape of demand draft in the name of APTDC Limited at the time of tenders.

3.7.2 Any Tender not having an acceptable Tender Security shall be rejected by the APTDCL considering it

as non-responsive and their Technical package shall not be opened and if opened then it will NOT be

evaluated. No post bid clarification shall be sought on tender security.

3.7.3 The Tender Security of the successful Tenderer shall be returned upon the execution of the Contract and the receipt by the APTDCL of the Security Deposit in accordance with Clause below. 3.7.4 The Tender Security of tenderers who fail in technical evaluation shall be returned after opening of financial package. Tender security of the unsuccessful tenderers in financial opening shall be released after

unconditional acceptance of the Letter of Acceptance (LOA) by the successful tenderer.

3.7.5 The Tender Security shall be forfeited:

• if the Bidder withdraws its Bid during the interval between the Bid Due Date and the expiration of the Bid Validity Period

• if the Selected Bidder fails to make the payments within the time specified in this tender document, or any extension thereof granted by APTDCL

• if the successful Tenderer refuses or neglects to execute the Contract or fails to furnish the required Security Deposit within the time specified or extended by the APTDCL

• if the Tenderer does not accept the arithmetic corrections to his Tender price, as per the relevant clause in the Tender document.


of 52

3.8 SECURITY DEPOSIT

3.8.1 The Security Deposit will be 10% of the total work order value and the same will be deducted from

each bill. The tender security of the successful bidder will be adjusted towards Security Deposit.

3.8.2 The said Security Deposit will be kept valid till the final settlement of accounts which shall be done in

maximum of 180 days of the end of the execution period.

3.9 PROPOSAL PREPARATION COST

The Bidder shall be solely responsible for all the costs associated with the preparation of its Bid and its

participation in the bidding process, including all types of due diligence that may be required for the

process. The APTDCL shall not in any way be responsible or liable for such costs, regardless of the conduct

or outcome of bidding.

3.10 VALIDITY OF OFFER

3.10.1 The Proposal shall remain valid for a period not less than one hundred eighty (180) days from the

Bid Due Date (“Proposal Validity Period” or “Bid Validity Period”). APTDCL reserves the right to reject any

Bid that does not meet this requirement. APTDCL may however request the Bidders to extend the validity

of their Bids for a specified additional period.

3.10.2 A Bidder agreeing to the request will not be allowed to modify its Bid, but would be required to

extend the validity of its tender security for the relevant period of extension.

3.10.3 The Bid Validity Period of the Selected Bidder shall stand extended till the date of execution of the

Work.

3.11 PREPARATION AND SUBMISSION OF PROPOSAL

The Bids should be submitted in the forms prescribed under this section, and the relevant Annexure in

Section 4.

3.11.1 The completed Bids shall be accepted only up to the date and time as specified in under the bid

schedule of Section-II of tender document. Bids have to be submitted to APTDC in person or by post.

APTDC will not be responsible for any delay in receipt of bid.

3.11.2 The Bidders shall furnish the information strictly as per the formats given in Section 4 of this

document without any ambiguity. The APTDCL shall not be held responsible if the failure of any Bidder to

provide the information in the prescribed formats results in a lack of clarity in the interpretation and

consequent disqualification of its Bid.

3.11.3 Deleted

3.11.4 Deleted


of 52

3.11.5 All Proposals/Bids shall be submitted by the bidder duly signed. In case of a Consortium, the

proposal shall be uploaded by the duly Authorized Signatory of the Lead Member. The Bidders shall submit

a supporting Power of Attorney (POA) authorizing the Signatory of the Proposal, to commit the Bidder and

agreeing to ratify all acts, deeds and things lawfully done by the said attorney and such POA shall be

signed by all members of the Consortium and shall be legally binding on all of them.

3.11.6 The Proposal shall be submitted duly signed by the Authorized Signatory in unequivocal acceptance

of all the terms and conditions of this Bid Document. All the alterations, omissions, additions, or any other

amendments made to the Proposal shall mandatorily be initialed by the Authorized Signatory.

3.11.7 All the witnesses and sureties shall be persons of status and probity and their full names and

addresses shall be stated below their signature. All signatures in the Bid Documents shall be dated.

3.11.8 Bidders are required to submit the Original tender document after downloading from the website

which must be signed on each page in acceptance of all the terms and conditions of the Bid Document.

3.12 SUBMISSION OF BIDS

3.12.1 ALL bidders should submit the bid Document cost and tender security (Originals) to the office of the

Superintending Engineer, APTDCL as specified in bid document.

3.12.2 The technical package/qualification documents shall be submitted physically in the office of the

Superintending Engineer, APTDC, Stalin Corporate, 5th

floor, Vijayawada, and shall contain the following:

Letter of Application and Interest (As per Annexure 1), General Information of the Bidder (As per Annexure

2), Summary of Financial Capability (As per Annexure 3), Power of Attorney for Signing Of the Application

(As per Annexure 8), Affidavit (As per Annexure 5), Original RFP Document duly signed (on each page) by

an authorized representative as a token of acceptance of all the terms and conditions. Drawing and design

of the proposed house boat considering the location of our proposed placement of boats in Andhra

Pradesh.

3.12.3 The Financial Proposal (as per Annexure 4) shall be submitted in a separate sealed cover.

3.12.4 Tenders received after due date and time of submission shall not be accepted.


of 52

3.13 BIDDER’S RESPONSIBILITY

3.13.1 It would be deemed that prior to the submission of the Bid, the Bidder has made a complete and

careful examination of a) The requirements and other information set forth in this tender document. b)

The various aspects of the offer (i) Project area, existing facilities, the access to the roads and the utilities;

(ii) All other matters that might affect the Bidder’s performance under the terms of this tender, including

all risks, costs, liabilities and contingencies associated with the project c) All the Bids shall be signed by the

Bidder or the duly authorized signatory of the Bidder. d) Bidder shall visit the Project Site at its own cost

before submitting the Bid.

3.13.2 APTDC shall not be liable for any mistake or error or neglect by the Bidder in respect of the above.

The Bids that are not substantively responsive to the requirements of this tender document shall be

rejected as non responsive.

3.14 MODIFICATION AND WITHDRAWAL OF PROPOSALS

3.14.1 No Proposal shall be modified or withdrawn by the Bidder after the Bid Due Date.

3.14.2 Withdrawal of a Bid during the interval between Bid Due Date and the expiration of the Bid Validity

Period would result in the automatic forfeiture of the tender security.

3.15 OPENING OF BIDS

3.15.1 The Technical Package of all tenderers who have submitted a valid tender security and cost of

tender document shall be opened in the presence of representatives of tenderers who choose to attend

on date & time as mentioned in tender document in the office of the Superintending Engineer, APTDCL, 5th

floor, Stalin Corporate, Autonagar, Vijayawada. Tenderers may visit APTDCL website to know latest

Technical Opening information after completion of opening process. Tenderers can also see the Technical

Sheets (check-list) of other tenderers after completion of opening process by log-in into the web-site. If

such nominated date for opening of Tender is subsequently declared as a Public Holiday by the

Government of Andhra Pradesh, the next official working day shall be deemed as the date of opening of

Technical Package. The Tender of any tenderer who has not complied with one or more of the foregoing

instructions may not be considered.

3.15.1 (a) If the documents do not meet the requirements of the APTDCL, a note will be recorded

accordingly by the Tender Opening Authority.

3.15.1 (b) The tenderers name, details of the tender security and such other details as the APTDCL or his

authorized representative, at his discretion, may consider appropriate will be announced at the time of

tender opening.

3.15.1 (c) The signed financial package which tenderer have submitted in a separate cover will be opened

on a subsequent date after evaluation of technical packages. Financial packages of only those tenderers

whose submissions are found substantially responsive and technically compliant to the tender


of 52

conditions will be opened. The time of opening of financial package shall be informed through website

only. Tenderers can visit to APTDCL website www.aptdc.gov.in for further information.

3.15.2 The APTDCL reserves the right to reject any Proposal and forfeit the tender security, if

a) It is not signed, sealed and marked as stipulated in Clause 3.15.

b) The information and documents have not been submitted as requested and in the formats specified in

the tender document.

c) There are inconsistencies between the Proposal and the supporting documents.

d) It does not mention the validity period as set out in Clause 3.13.

e) It provides the information with material deviations, which may affect the scope or performance of the

Project.

f) There are conditions proposed with the Technical and/or Financial Proposals.

3.15.3 A material deviation or reservation is one:

a) which affects in any substantial way, the scope, quality, or performance of the Project, or

b) which limits in any substantial way, inconsistent with the tender document, the APTDCL’s rights or the

Bidder’s obligations, or

c) which would affect unfairly the competitive position of other Bidders presenting substantially

responsive Bids.

d) No request for modification or withdrawal shall be entertained by APTDCL in respect of such Proposals.

3.16 RESPONSIVENESS OF BIDS

3.16.1 Before evaluation of Bids, APTDCL will determine whether the Bid is responsiveness to the

requirements of Bid Documents. A Bid/Proposal shall be considered ‘responsive’ only if:-

i) it is received by the deadline for submission of Bid/Proposal;

ii) It contains information complete in all respect as required in the Bid Documents(in the formats

specified);

iii) it is signed, sealed and marked as stipulated;

iv) it is accompanied by receipt of Bid Document Fee;

v) it is accompanied by the acceptable tender security/ Bid Security;


of 52

vi) it is accompanied by the relevant Power(s) of Attorney(ies) and Undertakings as specified in Bid Forms;

vii) The document is accompanied by the Checklist as prescribed.

3.16.2 If any of the above criteria is not fulfilled, in any manner whatsoever, the proposal shall be treated

as non-responsive. The decision of APTDCL on the responsiveness of the Bid shall be final and conclusive

and binding on the Bidder and shall not be called into question by any Bidder on any ground whatsoever.

Any Bid/Proposal which is non responsive shall be rejected.

3.16.3 To facilitate checking the responsiveness and evaluation of Bids, APTDCL may at its sole discretion,

without being under any obligation to do so, reserves the right to call for any clarification from any Bidder

regarding its Bid. Such clarification(s) shall be provided within the time specified by APTDCL for this

purpose. If the Bidder does not provide the clarification sought within the prescribed time, its Bid shall be

liable to be rejected. In case it is not rejected, APTDCL may proceed to evaluate the Bid by construing the

particulars requiring clarification to the best of its understanding.

3.16.4 No Bidder shall however have the right to give any clarification unless asked for by APTDCL, in any

manner whatsoever, with the bidding process, to intervene in, any manner whatsoever, in the bidding

process.

3.17 EVALUATION OF BIDS

Evaluation of Technical Proposals

The Bids of the Bidders shall be evaluated in two stages. “Tender Security” and “Technical Qualification”

will first be evaluated which will cover following items:

3.17.1 First of all it will be determined whether each tender is accompanied with the valid tender security

i.e. the required amount and in an acceptable form as stated in above Clause. Tenders not accompanied

with the valid tender security shall be rejected and may not be evaluated further. Other aspects of

technical evaluation will be done as per above clauses mentioned in the document.

3.17.2 Tenders not considered substantially responsive and not full-filling the requirements of the tender

document as evaluated above shall be rejected by APTDCL and shall not be allowed subsequently to be

made responsive by correction or withdrawal of the nonconforming deviation or reservation.

3.17.3 If any tender is rejected, pursuant to above paragraph, the Financial Package of such tenderer shall

not be opened.

3.17.4 The decision of the APTDCL as to which of the tenders are not substantially responsive shall be final.

3.17.5 In case of those Bidders who have not met the eligibility criteria then the Financial Bids of such

tenderer shall not be opened.


of 52

Evaluation of Financial Proposals

3.17.6 All technically acceptable tenders will be eligible for opening of their financial proposals. APTDCL

shall notify all technically qualified Tenderers to attend the opening of the financial proposal. The financial

proposal will then be opened in front of attending Tenderers.

3.17.7 The Bidders with the lowest Bid may also be requested to make a presentation at their own cost,

for clarifications, additional information on Bidder’s capability, concept plan and the business proposal in

this regard to APTDCL. APTDCL may seek further clarifications and make suggestions in respect of the

proposal which should not in any manner effect a change in the rate quoted by such Bidder and also

should not constitute any material deviation affecting the relative position of any Bidder and also should

not be inconsistent in any substantial way with the Bid Documents. The Bidder shall be obliged to

incorporate these suggestions in his planning/proposals.

3.17.8 The arithmetical errors will be rectified on the following basis. If there is a discrepancy between

words and figures, the amount in words will prevail. If the Bidder does not accept the correction of errors,

its Bid shall be rejected & the EMD shall be forfeited.

3.17.9 The Bidder found eligible and quoting the lowest rate in its Proposal shall normally be declared as

the Selected Bidder for the Project.

3.17.10 In the event of two or more Bidders quoting same amount in financial proposal for the Project,

APTDCL may ask the tie Bidders to submit their revised Financial Proposals with the amounts quoted by

them earlier as reserve price for such Financial Bid. In such case, the Bidder who amongst the tie Bidders,

quotes the lower amount in the revised Financial Bid will normally be declared as the Selected Bidder for

the Project.

3.17.11 However, the confirmation of the lowest Bid shall be at the sole discretion of the APTDCL who

does not bind itself to confirm to the lowest Bid and reserves the right to reject the Bid without assigning

any reasons whatsoever.

3.17.12 Further, in the event of the lowest Bidder withdrawing its offer or not being selected for any

reason in the first instance for the Project, (the "First Round of Bidding"), APTDCL without being under any

obligations to do so, may, at its sole discretion, either invite the next lowest Bidder to revalidate and/ or

extend its EMD, as necessary and also match the Bid of the aforesaid lowest Bidder for the Project or

annul the bidding process as deemed appropriate by APTDCL in its sole discretion,.

3.17 RIGHT TO REJECT BIDS

3.17.1 APTDCL reserves the right to reject any Bid if it is of the opinion that the Bidder lacks the expertise,

experience and is not in possession of requisite infrastructure required for the purpose of the Project. The

discretion of the competent authority of APTDCL in this respect shall be final and binding on all the

Bidders.


of 52

3.17.2 APTDCL reserves the right to reject any/all Bids including the lowest Bid or withdraw the Bid at any

stage without assigning any reasons whatsoever. Nothing contained herein shall confer a right upon a

Bidder or any obligation upon APTDCL.

3.17.3 The Bidder hereby voluntarily and unequivocally agrees that APTDCL shall not be under any

obligation or be liable for any acceptance, rejection or annulment of any/all Bids and the Bidder shall not

to seek any claims, damages, compensation or any other consideration whatsoever on this account, from

APTDCL.

3.18 MISREPRESENTATION/FRAUD/BREACH OF TERMS AND CONDITIONS

If it is discovered at any point of time that any Bidder has suppressed any facts or has given a false

statement or has made any misrepresentation or has committed a fraud or has violated any of the terms

of this Bid, the Bid shall be disqualified by APTDCL.

3.19 DISPUTES

3.20.1 All disputes between the successful Bidder and APTDCL shall be settled as per the Dispute

Resolution procedure. During the bidding process, no dispute of any type would be entertained. Even in

such cases where APTDC asks for additional information from any Bidder, the same cannot be adduced as

a reason for citing any dispute.

3.20.2 The Courts at Vijayawada/High court of AP shall have the sole & exclusive jurisdiction to try all the

cases arising out of this tender document.

3.21 CONFIDENTIALITY

3.21.1 The information relating to the examination, clarification, evaluation and recommendation for the

short-listed Bidders shall not be disclosed to any person not officially concerned with the process. APTDCL

will treat all the information submitted as part of all the proposals in confidence and will insist that all that

have access to such material treat it in confidence. APTDCL will not divulge any such information unless it

is ordered to do so by any Government Authority that has the power under law to require its disclosure or

due to statutory compliances.

3.22 ACCEPTANCE OF THE OFFER

3.22.1 After the Bids are accepted by the Competent Authority of APTDCL, the LOA shall be issued to the

Selected Bidder.


of 52

3.23 EXECUTION AGREEMENT

3.23.1 The Selected Bidder shall be required to deposit the requisite Security Deposit to the APTDCL within

7 days of issue of the LOA.

3.23.2 The formal Agreement shall be executed within a period of 7 days from the payment of security

Deposit by the Selected Bidder to the APTDCL. Prior to signing of the formal Agreement, the Selected

Bidder shall submit the certified true copies of all resolutions adopted by its/their Board of Directors

authorizing it/them for the execution, delivery and performance of this Agreement to the APTDCL.

3.23.3 In case of failure to sign the formal Agreement within the stipulated time, APTDCL shall retain the

right to cancel the LOA and forfeit the Bidder’s tender security and any other amount deposited till that

time without being liable in any manner whatsoever to the Selected Bidder.

3.23.4 Failure to meet the above mentioned conditions, shall be construed as a breach of the Selected

Bidder and APTDCL shall be entitled to cancel the LOA without being liable in any manner whatsoever to

the Selected Bidder and appropriate the tender security and any other amount deposited till that time as

‘Damages’.

3.24 UNSUCCESSFUL BIDDERS

The tender security received from the Bidders who are not selected shall be returned by APTDCL within 30

(Thirty) days of the declaration of the Selected Bidder. The tender security/ bid security shall be returned

without payment of any interest.


of 52

SECTION 4

GENERAL CONDITIONS

4.1 Tender validity period:

4.1.1 The tenders submitted shall remain valid for clear six months from the date of opening of technical

bid without any variation in price structure whatsoever. Withdrawal of tenders once submitted within this

period of six months will entail for forfeit of EMD automatically.

4.1.2 Guarantee:

Bidders will have to guarantee the house boats for a period of 12 months (One year) from the date of

delivery against any manufacturing defects subject to normal conditions of use. For this 10% of the value

of the order must be deposited in the form of Bank Guarantee. If not submitted equal amount will be

retained for 12 months from the last stage payment.

4.1.3 Personnel:

The tenderer should furnish, the full details of Naval Architects and other technical supervisory personnel,

failing which, the tender will be disqualified the bidder to whom the work is awarded shall ensure that the

Naval architect is always present at the site of work during working hours, personally checking all items of

work, and paying extra attention to the works as may demand special attention e.g. preparation of

drawings, fabrications, structural connections etc.

4.1.4 Equipment:

The bidder shall clearly indicate the list of equipment including the type, make, model which he will assign

to the work if his bid is accepted, stating what equipment belongs to him and what equipment he is going

to purchase/ to hire for the work. The tender committee will decide whether the list of equipment

proposed by each bidder are adequate or not?

4.1.5 Financial Capacity:

The financial capacity of the bidder will be judged from the financial statement that the bidder shall

submit with his tender as well as from the letters issued by his bankers regarding his credit worthiness.

4.1.6 Commencement Date:

The written agreement to be entered in to between the successful bidder and APTDC Ltd. shall be the

foundation of the rights and obligation of both the parties and the successful bidder shall not deemed to

be commenced until the agreement is first signed by him and APTDC Ltd. The date of signing of agreement

is the commencement date for all practical purposes. The bidder shall start the construction within 15

days on the receipt of approved drawing.


of 52

4.1.7 Rates:

a. The rates quoted should be firm & fixed without any variation valid till completion of order

including all Taxes, Duties, Transportation, approvals from the government agencies and

Launching charges etc.

b. APTDCL will not provide any form for statutory rebate and the bidder should fully satisfy himself

regarding the various taxes & duties applicable before submission of bid.

c. The rate should be written both in words and figures and the unit in words. The tenderer should

also show the grand total of the whole contract and quote in the tender a lump sum for which he

will undertake to do the whole work subject to the conditions of the order.

d. Rates or lump sum amounts for items not called for shall not be included in the tender. No

alterations which are made by the tenderer in the tender documents will be recognized and if any

such alterations are made, the tender will be void.

e. In order to facilitate uniform comparison, the tenderer shall not add any conditions of his own in

the tender which may affect the rates called for. However, if the tenderer wishes to introduce any

conditions not specified in the tender documents, the same must be brought into the knowledge

of APTDCL authorities before or at the time of pre bid meeting. If the modification suggestion is

acceptable and required in the interest of APTDCL, the tender committee will make necessary

corrections in the tender document by bringing an addendum to this tender document and the

same will become the part of this tender document. No suggestion/request for modification will

be entertained post pre-bid meeting but APTDCL can modify the tender document clause post

prebid meeting with the intimation to the bidders.

4.1.8 Delivery:

Time is the essence of the contract. The delivery schedule shall be 6 months from the date of entering of

agreement for the House boat.

4.1.9 Variation in quantities of item of work:

The technical member as authorized by APTDC Ltd., shall have the privilege of ordering modifications,

omissions or additions at any time before the completion of the work. The builder is bound to execute all

the supplemental items that are found essential, incidental and inevitable during the execution of the

work, at the rates to be worked out mutually as per existing market rates if they are not covered in the

agreement items.


of 52

4.1.10 Income Tax:

GST/Income Tax will be deducted at source from each bill as per prevailing rates in Income Tax

Department applicable to works contracts. 4.1.11 Penalty Clause:

In the event of placement of order if the builder fails to deliver the House boats in complete shape afloat,

as per the delivery schedule mentioned, penalty shall be levied on the builder at the rate of Rs.10,000/-

per day for first 15 days of delay and thereafter Rs.15,000/- per day up to next 15 days. The maximum

penalty limited to 10% of the tender value.

4.1.12 Insurance:

The builder shall secure and maintain throughout the duration of this contract, insurance of all risks

coverage in such amounts as may be necessary to protect himself and interest of APTDC Ltd., against all

hazards or risks of loss. It shall be the responsibility of the builder to maintain adequate insurance

coverage including Terrorist Act at all times. Failure of the builder to maintain adequate coverage shall not

relieve him of any contractual responsibility or obligation.

4.1.13 Claims and Disputes:

Any claims or disputes arising out of the contract should be promptly submitted in writing to APTDCL Ltd.,

within 15 days from the Date of cause of action, so that the point of issue could be immediately verified at

site by the field officers, facts ascertained and a prompt decision given. Claims raised well beyond this time

as to make it difficult to verify the facts are liable to be rejected. The tenderers shall carefully note this

stipulation. 4.1.14 Legal:

Any legal dispute shall be subject to the Jurisdiction of Vijayawada/High court of Andhra Pradesh only.

4.1.15 Arbitration Clause:

In the event of any dispute or differences arising between the parties as to the interpretation, operation or

effect of any clause of the agreement to be executed with the Corporation or any of the terms and

conditions contained herein which shall be made integral part of the agreement such dispute or difference

shall be referred to the sole arbitration of a person appointed by Govt. of Andhra Pradesh., and there shall

be no objection if Govt. appoints any officer who has in the discharge of his duties as such


of 52

officer, has either expressed any opinion or issued any direction in the matter and the provisions of the

Arbitration Act 1996 shall apply to such arbitration. 4.1.16 Force Majeure Clause:

If, at any time during the continuance of this order the performance in whole or in partly by either party or

any obligation under this order is prevented or delayed by reasons of any war, hostility, acts of public

enmity, civil commotion, sabotage, fires, floods, explosions, epidemics, Quarantine restrictions or other

acts of god, provided notice of the occurrence in any such event is given by either party to the other within

TWENTY ONE DAYS from the date of occurrence thereof, neither party shall have claim for damage against

the performance and deliveries in such cases shall be resumed as soon as practicable after such an event

has come to an end or has ceased to exist.

4.1.17 Materials:

All materials required for the construction of House boats, out-fit equipment etc., shall be procured by

builders at his own cost. The Contract’s lump sum rate for the item in the price schedule shall be for

finished work as per specifications in Annexure - I and supply of the House boats in good working

condition afloat at specified destinations in Andhra Pradesh and shall include the cost of all materials,

outfit equipment, all taxes, royalties, public body taxes, transportation, handling and all incidental and

labour charges and launching etc.

No claim towards the taxes paid by the Builder for the procurement of the above materials or increase in

the wages of labour and in the taxes leviable on APTDC Ltd.

The rate quoted for the item should be lump sum and should hold good till the completion of the work

even if extension of contract period is granted by the Corporation. Claims towards price variation on any

account will not be entertained. 4.1.18 Design Approval:

After the award of contract order, the Builder has to obtain design drawings prepared are approved by

suitable competent agency at his own cost. 4.1.19 A specimen profile & plan of house boat which is purely indicative as shown in Annexure is attached

for guidance. 4.1.20 Inspection of Work:

During the execution of the contract, the Builder should get the work inspected by the authorized officer

of the corporation or any other government agency suggested by APTDC at every stage and a certificate

from the above inspecting officer to the effect that the work done is satisfactory and as per the approved

drawing should invariably be submitted to the corporation along with claim for “Stage Payment”.


of 52

4.1.21 PAYMENT & CERTIFICATES:

Payment:- Payments to the builder will be made under stages out lined below

S.No Stage Percentage of

payments

1 Fabrication of Hull And 25%

Completion of Hull

With minimum 6 mm thick

MS sheet

2 Completion Of Hull With 35%

engine room machinery And

stern gear

3 Establishment interiors as Per 25%

the each Room Inventory

placement and completing the

House boat in all aspects

4 Trials and stability testing and 15%

Handing Over to The

Corporation along with concern

test certificates and stability

Booklet

If 10% Material Guarantee in the shape of Bank Guarantee is not produced and the same amount will be

retained for 12 Months from the last stage payment and will be released after guarantee period is over.

The percentages noted against each stage is on the lump sum rate quoted by the contractor. Bills should

be prepared in triplicate by the contractor and marked distinctly as original, duplicate and triplicate and

dispatched to APTDC Limited, Vijayawada quoting reference to the agreement along with an advance

stamped receipt. Payment to the contractor will be paid as per the stages mentioned.

4.1.22 Service during guarantee period:

Any repairs / damages during guarantee period must be made good within one week after receipt of

intimation. Failure on the part of the party to comply with the above will be liable for penalty.


of 52

APTDCL reserves the right to consider the House boats quality in full or part as per the requirement and the priority.

4.1.23 Inspection:

Andhra Pradesh Tourism Development Corporation Ltd., reserved the right to inspect the House boats

during the process of manufacture or after completion and bidder will have to rectify any defects,

deviations as may be noticed by the technical officer appointed by APTDCL for the purpose. 4.2 Approvals from APTDCL:

4.2.1 All communication in all matters regarding this tender related to the Procurement of House Boats for

APTDC Ltd. shall be forwarded to the nodal officer as appointed by the APTDCL. The nodal officer shall act

as a single window for the Lessee and shall be responsible for all the matters related to this tender

4.2.2 The bidder shall forward all requests related to this tender to the nodal officer. Such requests, if

completed in all manners, may be approved / rejected by the APTDCL within 15 days of the receipt of the

request.

4.2.3 The nodal officer for this Bid will be the Superintending Engineer and or General Manager (Water

fleet), APTDCL/or any other officer appointed by APTDC.

4.3 STATUTORY CLEARANCES

4.3.1 The successful bidder shall be required to get the House Boat Drawing & design approved by the

competent authorities of the State and central Govt. if any at his own cost.

4.3.2 Not withstanding anything mentioned above, the successful bidder is required to adhere to the

statutory provisions of the prevailing Act/ Rules and bye-laws of the Govt. of Andhra Pradesh and GoI over

the works to be undertaken.

4.3.3 The lowest tenderer shall obtain all clearances and approvals as required from the competent

authorities for building the House Boats. It is to be clearly understood that all such clearances are to be

obtained by the successful bidder and the APTDCL may only provide assistance wherever possible without

any obligation.

4.3.4 Procuring all the permissions required from the statutory/ regulatory/ civic authorities concerned

during construction period and also on completion to run the House boat at the designated location will

be sole responsibility of the successful tenderer. APTDCL shall not be responsible for any such

procurement and shall not entertain any claims in this regard. APTDCL may only provide assistance

wherever possible without any obligation.


of 52

TECHNICAL SPECIFICATIONS

5.1.1 GENERAL SERVICE CONDITION: The House boats with MS superstructure with Bedrooms, Kitchen, lobby and other facilities intended for

using it for tourists purpose. The G.A sketch is enclosed to this tender for guidance only.

5.1.2 DELIVERY OF HOUSE BOATS The delivery of the House boat Hulls shall be afloat at the respective location. The House boats shall be

anchored at locations through wire rope / chain of the winch.

5.1.3 ANCHORING OF THE HOUSE BOATS: The House boats shall be supplied with suitable Anchors. The number & design of the Anchors shall be

as per the standard norms. The intending bidders shall clearly indicate the detailed Anchoring system in

their technical bids. This should ensure problem free operation.

5.1.4 PLACE OF CONSTRUCTION: The construction of the House boats are to be carried out on the banks of specified water bodies at

a suitable land convenient for launching and construction. The intending bidder may satisfy himself of

the suitability of the land for manufacturing / Fabricating/ assembling Hulls and transferring it to the

delivery site before bidding.

(OR)

Alternatively fabricated sections can be assembled at the site and launch the same in specified water

bodies.

5.1.5 APPROVING AUTHORITY

a) The successful bidder shall submit the detailed drawing along with detailed specifications

General arrangement, Engine room machinery, transmission system (Both inboard and

out board arrangement) and obtain approval from competent authority.

b) The successful bidder should submit the certificate from competent authority for

specifications and drawings. The construction drawings need to be approved by concern

competent Agency.


of 52

5.1.6 SPECIFICATIONS AND DIMENSIONS FOR GUIDANCE ONLY: - HOUSE BOATS SPECIFICATION (Only for guidance) One Double Bedded room House Boat

Two Double Bedded room House Boat

Four Double Bedded room House Boat

a) Length : 19.00 Mts. b) Breadth : 4.80 Mts. c) Deapth : 1.40 Mts. d) Draft : 0.50 Mts.



All the other details are common for all the vessels

The above dimensions are given to indicate the general idea of the size of the House boat with Engine

Room. The G.A given by APTDCL is only for guidance. However, the actual size and design may be varied

slightly to suit the requirements of design and approval of the design by a recognized Approval agency.

Suitable shafting system with a suitable propeller and rudder arrangement is to be carried out.

5.1.7 MATERIAL & WORKMANSHIP:

The House boat should be built to the highest class of floating crafts building. All material used for

construction of hull, fittings are to be the best of their respective and in accordance to the standard

practice of House boats.

5.1.8 DESIGN:

The contractor shall be entirely responsible for the structural strength, stability, draft and performance of

the House boat. He should satisfy himself that the design is well suited for services intended. The design of

House boat and anchoring mechanism and other requirements shall be as per the directions and approval

of the recognized agency.


of 52

5.1.9 TESTING: All necessary testing during the time of construction and other test after construction like inclination

tests, stability tests, loaded condition, and any other trials as prescribed by the officer authorized by

APTDC Ltd shall be carried by the successful bidder.

5.1.10 DEPARTURE FROM SPECIFICATIONS:

Firms tendering are at liberty to propose modifications where, their standard practice, departs from these

specifications before or at the time of prebid meeting. If the modification suggestion is acceptable and

required in the interest of APTDC, the tender committee will make necessary corrections in the technical

specifications by bringing an addendum to this tender document and the same will become the part of this

tender document. No suggestion/request for modification will be entertained post prebid meeting but

APTDC can modify the tender document clause post prebid meeting with the intimation to the bidders.

5.1.11 GURANTEED TECHNICAL PARTICULARS: The Guaranteed Technical Particulars must be uploaded along with the Technical bid.

5.1.12 GENERAL DESCRIPTION:

The House boat is to be constructed for the services intended. The proposed hull design, scantlings, shall

all confirm to the approved drawing and standards.

BULK HEADS:

The House boat is to be fitted with watertight bulkheads. Necessary fittings for draining water from each

compartment must be fitted together with an bilge pump. The construction and design of bulkhead

section shall be as per regulations and standard practice.

5.1.13 DECK FLOOR:

The deck shall be with Marine Ply with cover of not less than 6.0 mm thick or as per the directions of the

departmental engineer/officer

5.1.14 FENDERS:

Two numbers suitable fenders to the House boats shall be provided.


of 52

5.1.15 LIFE SAVING & FIRE FIGHTING: Life jackets and all other safety equipments specification for such type of House boat must be supplied as

per standard practice depending upon the number of persons (Passengers and staff).

5.1.16 STABILITY CALCULATIONAS: Must be submitted along with the delivery of the House boats.

5.1.17 PAINTING:

The entire House Boat shall be thoroughly cleaned and coated with suitable Marine paints as per the

standard practice. APTDCL logo shall be painted on both sides of the House Boats.

5.1.18 INSPECTION:

APTDCL reserves the right to inspect the House Boats during the process of manufacture or after

completion and bidder will have to rectify the defects, deviations as may be noticed by our officers

appointed for this purpose. APTDC Ltd. reserves the right to accept any offer irrespective of price whose

design of the House boat is found to be more suitable for the concern location. APTDC Ltd. reserves the

right to accept or reject any tender or all the tenders, accepted any tender in full or part without assigning

any reasons thereof.


of 52

ONE DOUBLE-BEDDED ROOM HOUSE BOAT – PRINCIPLE PARTICULARS

Fore peak

Bed room with attached bath and toilet

Crew toilet

Kitchen

Aft deck

6.1.1 General Description:-

• The Hull is to be designed to ply in backwaters of Andhra Pradesh area during fair weather conditions.

• Standard safety features including watertight bulkheads and buoyancy chambers to be provided.

• The Hull to be divided in to 6WT compartments using 5 nos bulkheads. The boat Hull to be

fabricated with min 6 mm thick MS sheet of best quality material recommended for standard

marine construction.

• The super structure to be with MS the design to create local area ambience or as per the

directions of the departmental engineer/officer.

6.1.2 Watertight compartments of Hull:-

The Hull to be of 6 compartments – Forepeak, Ford storage space, fresh water and fuel storage, waste

collection tank area, Engine room and rudder compartment area.

6.1.3 Main Engine:- ALM 4 CTI with 2:1 Gearbox.

6.1.4 Fuel tank:- 1 No 300L fuel tank to be provided.

6.1.5 Bilge system:- A semi rotary pump to be provided at the Deck, ford and aft to bilge out the water from compartments.


of 52

6.1.6 Stern gear system:-

A stern gear assembly comprising of brass stern tube, inner and outer stuffing gland cutlass rubber bushes,

3 bladed Bronze propeller, nut and key to be provided, care to be taken for proper alignment of shafting

system.

6.1.7 Electrical fittings:-

Sl.No Item Installation Quantity

1 Navigation lights P&S lights 1 each

2 Navigation lights Search light 1 No

3 Bed room light ceiling 10/15 w LED Warm

white 2 Nos- LED Warm white

4 Bed room Reading lamp 2 Nos 10 w On either side of the bed LED 10/15W white colour 2 Nos in each bed

LED room

5 Toilet Lights Ceiling 1 No in each toilet

6 Havells/Panasonic Exhaust fan 40 w Ceiling / Side 1 No each in toilets +

one in kitchen

7 Modular Power plug 5 A Bed Room 3 x 2 room

8 Modular Power plug 15 A Kitchen 2

9 Modular Power plug 5 A Engine room 1

10 Emergency light Galley Bed room, Galley 10 w LED 1

Forward & ER Ceiling 10 w LED 1

11 Havells/Crompton/Bajaj Fan 60 w Bed room 1 no

12 Mini Freezer Kitchen 1 No.

13 A/C 1.5 Ton split with remote Bed room 1 no in each Bed room

14

Generator Kirloskar Green Engine room 1 No. to cater the full load or as directed by

Engineer-in-charge

The above material/quantity are tentative and has to be provided as per the actual requirement or as

per the directions of the departmental engineer/officer

6.1.8 Fresh water tanks:-

2 Nos fresh water tanks having a capacity of 500 L (Total 1000 Ltrs) to be provided.

6.1.9 Firefighting Appliances:-

1 No 9L dry powder fire extinguisher


of 52

1 No 2L Foam fire extinguisher

2 Nos Fire Buckets

2 Nos sand scoop to be provided

6.1.10 Life saving equipment:-

Sl. No Items Quantity

1 Life jackets Adult 5 Nos

2 Life buoys 5 Nos

The above material/quantity are tentative and has to be provided as per the actual requirement or as

per the directions of the departmental engineer/officer

6.1.11 Air conditioning unit:- One split A/c (1.5 Tone) Daikin/Mitsubishi/Ogeneral with copper fins suitable to operate in sea weather

conditions driven by 220 Volts power supply from the Generator while cruising with provision for shore

supply to be provided to Bed room. Each bed room – 01 (1.5 Ton capacity) or as directed by departmental

officer

6.1.12 Generator:-

Kirloskar Green Generator to be provided to cater the full load as per the capacity of the house boat or as

per the directions of the departmental officer

6.1.13 Inverter:-

One number, 1 KVA inverter to be provided for lighting .

6.1.14 Floor:- The flooring to be a combination of GRP sandwich with transverse and longitudinal grid / suitable

frames. The forepeak, kitchen & Aft peak to be Vinyl sheeted and the other areas to be of good quality

water resistant parquets or as per the directions of the departmental engineer. Toilets to be tiled.

6.1.15 Canopy / super structure:- The MS super structure to be design/as desired by APTDC (The successful bidder must submit the designs

along with material so that APTDC will select the design to suit the ambience of the environment/As directed

by Engineer-in-charge

6.1.16 Dining area / Lobby:-

2 Tables with 4 chairs (set) to be provided. The floor of Dining / Lobby to be of hard wood panels. Table

and chairs to be of very high quality with state of art design as per the choice of the APTDCL.


of 52

6.1.17 Bed room:-

The frame structure will be decided by the officer/engineer and has to be taken up as per the directions

of the departmental engineer.

6.1.18 Kitchen equipment:-


1 Stainless steel swing 1 no

2 Modular cabinet 1 set

3 Water connection 1 point

4 Ice box 1 No 100L

5

Electricals As per the drawing and requirement/ As per the

directions of Enginner-in-charge (Makes:

Anchor/Legrand/Havells/Panasonic)

• Kitchen / pantry slab to be paved with Granite.

• Inside of kitchen roof to be aluminum sheathed for fire protection.

• Cutlery / crockery storage racks and cooking provision to be established.

6.1.19 Toilet:-


1 European closet, Hindware make Cascade model 3 No (1 each)

2 Shower, Jaquar make 1 no each in attached bath room

of bed room

3 Shower, Jaquar make 1 No each in attached bath room

of bed room

4 Mirror 3 nos (1 each)

5 Towel Holder, Jaquar make 3 nos (1 each)

6 Soap tray, Jaquar make 3 nos

7 Health faucet, Jaquar make 3 nos

8 Napkin Holder, Jaquar make 2 sets in 2 attached bath rooms

All the above quantity/quality are tentative/Indicative. The quantity must be as per actuals or as per the directions of the departmental engineer.

6.1.20 Fender:-

Suitable fender to be provided on both sides of the House boat Hull.

6.1.21 Room partition:-


of 52

The room partition to be out of 6 mm thick marine plywood pigmented to APTDCL choice.

6.1.21 Painting / pigment:-


1 Steel structure 1 Coat epoxy primer surface and

2 coats of epoxy finish

2 Hull Gel coat/As desired by Engineer in

Charge

3 Room partition mat finish

4 Fender Enamel two coats WWD primer

plus two coats of finishing

Enamel

6.1.22 Bed room:-


1 Cot with 6” PU foam mattress 1 Nos

2 Pillows with cover 4 Nos

3 Wardrobe 1 No in each bed room

4 Chair 2 Nos in each bed room

5 Table with chairs 1 table with 4 chairs

The above quantity/quality are tentative/Indicative. The quantity must be as per actuals or as per the directions of the departmental engineer.

6.1.23 Lobby:-


1 Setty 1 set double and two single

2 Tea pot 1 No

• All the door fittings including the main lock to be Mortise make and brass/SS as suggested by

APTDC


of 52

Formats for Submission

Annexure 1

Letter of Application

(To be submitted and signed by the Bidder’s authorized signatory)

The Superintending Engineer,

Andhra Pradesh Tourism Development Corporation Limited,

5th

Floor Stalin Corporate,

Autonagar

Vijayawada - 520007

Sub: - Purchase of 1 (One) No. House Boat to APTDC

Sir,

1. Being duly authorized to represent and act for and on behalf of...……………. (hereinafter referred to as

the “Bidder”), and having studied and fully understood all the information provided in the Bid Document,

the undersigned hereby applies as a Bidder for Purchase of 1 (One) No. House Boat to APTDC

,according to the terms & conditions provided by APTDC

2. Our Technical & Financial Bid as per the requisite formats along with the supporting documents, duly

filled and signed on each page are enclosed in separate sealed envelopes as specified.

3. APTDCL and its authorized representatives are hereby authorized to conduct any

inquiries/investigation to verify the statements, documents and information submitted in connection with

the application and to seek clarification regarding any financial and technical aspects. This letter of

application will also serve as authorization to any individual or authorized representative of any institution

referred to the supporting information, to provide such information deemed necessary and requested by

your selves to verify statements and information provided in the application or with regard to the

resources, experience and competence of the Bidder.

4. APTDCL and its authorized representatives may contact the following persons for any further

information:

Name of the person (s): …………

Address: ……………………………………..

Phone: ……………………..…... Fax: ………………….

5. This application is made with full understanding that:


of 52

(a) Bids will be subject to verification of all information submitted at the time of bidding.

(b) APTDCL reserves the right to reject or accept any bid, cancel the bidding process, and / or reject all

bids.

(c) APTDCL shall not be liable for any of the above actions and shall be under no obligation to inform the

Bidder of the same.

6. We, the undersigned declare the statements made, and the information provided in the duly

completed application forms enclosed, are complete, true and correct in every detail.

7. We hereby confirm that we have read, understood and accepted all the detailed terms and conditions

of this RFP and Project related Information as required for the Bid. We have also visited the Project Site for

the assessment and have made our own due diligence and assessment regarding the Project.

8. We agree to keep our offer valid for one hundred twenty (90) days from the date of submission of

Proposal thereof and shall not make any modifications in its terms and conditions, which are not

acceptable to the APTDC and are in violation of the terms of the Bid Documents. We hereby agree to abide

by and fulfill all the terms, conditions and provisions of the aforesaid documents.

9. This application is made with the full understanding that the validity of bids submitted by us will be

subject to verification of all information, terms and conditions submitted at the time of bidding and its

final acceptance by APTDCL. We agree that, without prejudice to any other right or remedy, APTDC shall

be at liberty to forfeit the entire Tender Security.

Authorized signatory

Date:

Name and seal of Bidder

Place:

Encl:

1) The EMD/s of Rs. ________ lakh (Rupees ___________ only) and/or _____________/- (Rupees _____________ only) in the form of Demand Draft/Pay Order/ _____drawn upon __________ (bank)

dated ________.

2) Power Of Attorney for signing of Application Board resolution authorizing the signatory (Suggested

Format at Annexure 8)

3) Relevant Submissions as per the given Formats


of 52

Annexure 2

General Information of the Bidder

1. (a) Name:

(b) Country of incorporation:

(c) Address of the corporate headquarters and its branch office(s), if any, in India:

2. Details of individual(s) who will serve as the point of contact / communication for DMRC within the

Company:

(a) Name :

(b) Designation :

(c) Company :

(d) Address :

(e) Telephone Number :

(f) Fax Number :

(g) E-Mail Address :

For and on behalf of (Name of the Bidder)

Designation

Place:

Date:


of 52

Annexure 3

Summary of Financial Details

S.N. Description Financial Data for Latest Last 3 Years (Indian Rupees)

2015-16 2016-17 2017-18

1 Total Assets

2 Total External Liabilities

3 Net Worth [= 1 - 2]

4 Annual turnover

Note:

1) Attach certified copies of Annual Audited Balance Sheets and IT Returns Certificate for the preceding 3

(Three) years.

2) The above data must be submitted for all Relevant Consortium members, duly certified by

CA/Statutory Auditor.

3) Historic financial statements shall be audited by Statutory Auditor of the Company under their seal &

stamp and shall be strictly based on Audited Annual Financial results of the relevant period(s). No

statements for partial periods will be accepted.

Signed

(Name of the Authorized Signatory)

For and on behalf of

Signature of CA/ Statutory Auditors

(with seal & registration no.)

(Name of the Bidder)

Designation

Place: Date:


of 52

Annexure 4

Format for Financial Proposal for Purchase of 1 (one) Nos, House Boats to APTDC

(To be submitted and signed by the Bidder’s authorized signatory with the quoted recurring payment.)

The Superintending Engineer,

Andhra Pradesh Tourism Development Corporation Limited,

5th

Floor Atalin Corporate,

Auto Nagar,

Vijayawada - 520007

Sub: - “Purchase of 1(One) No. House Boats to APTDC

Sir,

We hereby submit our Financial Offer for the Project. If the Project is awarded to us, we agree to make the

following payments to APTDCL as per the terms given in the Request for Proposal (RFP) Document.

1. In an event, we are the selected bidder; any failure to deposit the original copy of tender Security within

stipulated time from the issue of LOA would entitle the APTDCL to forfeit the Tender Security.

2. The arithmetical errors will be rectified on the following basis. If there is a discrepancy between words

and figures, the amount in words will prevail. If I/we do not accept the correction of errors, this Bid will be

rejected & Tender Security will be forfeited.

3. Service tax as applicable and other applicable taxes including way bill from time to time will also be paid

by us/me in addition to the aforesaid charges.

This offer is being made by us/me after taking into consideration all the terms and conditions stated in the

RFP document, and after careful assessment of the spaces, all risks and contingencies and all other

conditions that may affect the financial proposal. We agree to keep our offer valid for 90 days from the

due date of submission of this Proposal.

Authorized signatory

Date:

Name and seal of Bidder

Place:


of 52

Annexure 5

Affidavit

(Notarized on Stamp Paper of Requisite Value as per Applicable Law)

I,, ………………. S/o …………..,resident of ………………., the ……………...(insert designation) of the ………………..(insert name of the single bidder/consortium member if a consortium), do solemnly affirm and state as follows :

1. I say that I am the authorized signatory of …………..(insert name of company /consortium member)

(hereinafter referred to as “Bidder/Consortium Member”) and I am duly authorized by the Board of

Directors of the Bidder/Consortium Member to swear and depose this Affidavit on behalf of the

Bidder/Consortium Member.

2. I say that I have submitted information with respect to our eligibility for Andhra Pradesh Tourism

Development Corporation's (hereinafter referred to as “APTDCL”) Purchase of 1 (One) No. House boats

to APTDC (hereinafter referred to as “Project”) Request For Proposal (‘RFP’) Document and I further state

that all the said information submitted by us is accurate, true and correct and is based on our records

available with us.

3. I say that, we hereby also authorize and request any bank, authority, person or firm to furnish any

information, which may be requested by APTDCL to verify our credentials/information provided by us

under this Bid and as may be deemed necessary by APTDCL.

4. I say that, we fully acknowledge and understand that furnishing of any false or misleading information

by us in our RFP shall entitle us to be disqualified from the bidding process for the Project. The costs and

risks for such disqualification shall be entirely borne by us.

5. I state that all the terms and conditions of the Request for Proposal (RFP) Document have been duly

complied with.

VERIFICATION :- DEPONENT

I, the above named deponent, do verify that the contents of paragraphs 1 to 6 of this affidavit are true and

correct to my knowledge. No part of it is false and nothing material has been concealed. Verified at ………………………, on this …………………. .day of………….……..,2015.

DEPONENT


of 52

ANNEXURE 7

FORMAT FOR POWER OF ATTORNEY FOR SIGNING OF APPLICATION

Know all men by these presents, we ……………………………………. (name and address of the registered office) do hereby constitute, appoint and authorize Mr./Ms…………………..(name and residential address) who is presently employed with us and holding the position of ………………………….as our attorney, to do in our name and on our behalf, all such acts, deeds and things necessary in connection with or incidental to our

bid for the Project, including signing and submission of all documents and providing

information/responses to APTDCL, representing us in all matters before APTDCL, and generally dealing

with APTDCL in all matters in connection with our Bid for the Project. We hereby agree to ratify all acts,

deeds and things lawfully done by our said attorney pursuant to this Power of Attorney and that all acts,

deeds and things done by our aforesaid attorney shall always be deemed to have been done by us.

For………………………………………….

Accepted

…………………………………. (Signature)

(Name, Title and address) of the Attorney

Note:

* The mode of execution of the Power of Attorney should be in accordance with the procedure, if any, laid

down by the applicable law and the charter documents of the executants and when it is so required the

same should be under common seal affixed in accordance with the required procedure.


of 52

ANNEXURE 8

LIST OF USAGES BANNED

1. Any product / Service the sale of which is unlawful /illegal or deemed unlawful under any Indian act or

legislation.

2. Any product the storage and sale of which may lead to or be considered as a fire hazard; such as fire

crackers, industrial explosives, chemicals etc.

3. Storage of sale of tobacco and tobacco products.

4. Coal based cooking is strictly prohibited. Gas Based Cooking shall also be permitted as per APTDCL’s

extant Policy / guidelines.


of 52

ANNEXURE- 9(As per Clause 3.5.5 of Section-III)

UNDERTAKING FOR CORRUPT & FRAUDULENT PRACTICE

We declare that in the submission of this Tender no agent, middleman or any intermediary has been, or

will be engaged to provide any services, or any other item of work related to the award and performance

of this Contract. We further confirm and declare that no agency commission or any payment which may be

construed as an agency commission has been, or will be, paid and that the tender price does not include

any such amount. We acknowledge the right of the Employer, if he finds to the contrary, to declare our

Tender to be non-compliant and if the Contract has been awarded to declare the Contract null and void

STAMP & SIGNATURE OF AUTHORIZED SIGNATORY

Two DOUBLE-BEDDED ROOM HOUSE BOAT – PRINCIPLE PARTICULARS The below quantity/quality are tentative/Indicative. The quantity must be as per actuals or as per the directions of the departmental engineer.

Fore peak

Bed room with attached bath and toilet

Crew toilet

Kitchen

Aft deck

Dining

6.1.1 General Description:-




fabricated out of best quality 6mm MS sheer recommended for standard marine construction.


of 52

• The MS super structure to be design to create local area ambience or as desired by departmental

engineer.

6.1.2 Watertight compartments of Hull:- The Hull to be of 6 compartments – Forepeak, Ford storage space, fresh water and fuel storage, waste


6.1.3 Main Engine:- ALM 4 CTI with 2:1 Gearbox.

6.1.4 Fuel tank:-

1 No 300L fuel tank to be provided.

6.1.5 Bilge system:-

A semi rotary pump to be provided at the Deck, ford and aft to bilge out the water from compartments.


of 52




system.








LED Room



one in kitchen

7 Modular Power plug 5 A Bed Room 3 x 2 rooms

8 Modular Power plug 5 A Kitchen 2 Nos.

9 Modular Power plug 5 A Engine room 1 No.

10 Emergency light Galley Bed room, Galley 10/15 w LED 1

Forward & ER Ceiling 10/15 w LED 1

11 Havells/Crompton/Bajaj Fan 60 w Bed room 1 no in each bed room

12 Daikin A/C 1.5 Ton split with remote Bed room 1 no each bed room

13 Generator KVA Kirloskar Green Engine room

1 No. to cater full load/ as directed by engineer-

in-charge







2 Nos Fire Buckets



of 52



1 Life jackets Adult 10 nos (As per standard requirement depending on no. of persons)

2 Life buoys 10 nos (As per standard requirement depending on no. of persons)


6.1.11 Air conditioning unit:-

One split A/c (1.5 Tone) Daikin/Mitsubishi/O general with copper fins suitable to operate in sea weather


supply to be provided to Bed room. Each bed room – 01 (1.5 Ton capacity)

6.1.12 Generator:-

Kirloskar Green Generator to be provided to cater the full load of the house boat or as directed by the

Engineer in-charge

6.1.13 Inverter:-

One number, 1 KVA inverter to be provided.



water resistant parquets or as per the directions of the departmental engineer. Toilets to be tiled.

6.1.15 Canopy / super structure:-

The MS super structure to be designed as desired by APTDC. The successful bidder must submit the designs

along with material so that APTDC will select the design to suit the ambience of the environment/As per the

directions of Departmental in charge.


2 Tables with 8 chairs (set) to be provided. The floor of Dining / Lobby to be of hard wood panels. Table

and chairs to be of very high quality with state of art design as per the choice of the APTDCL.


of 52

6.1.17 Bed room:-

The frame structure will be F.R.P and one side and 6 mm plywood will be used for making partition.


Sl. No

Items Quantity




4 Mini Freezer 1 No.

5 Ice box 1 No 100L

6 Electricals As per the drawing and requirement




6.1.19 Toilet:-




of bed room


of bed room

4 Mirror 3 nos (1 each)

5 Towel Holder, Jaquar make 3 nos (1 each)

6 Soap tray, Jaquar make 3 nos

7 Health faucet, Jaquar make 3 nos


The above quantity are tentative/indicative. The quantity must be as per requirement and as per the directions of the departmental engineer

6.1.20 Fender:-





of 52





2 Hull Gel coat/As desired by the Engineer

in charge




enamel

6.1.22 Bed room:-


1

Cot with 6” PU foam mattress 1 Nos in Each bed room

2 Pillows with cover 4 Nos in each bed room

3 Wardrobe 1 No in each bed room

4 Chair 2 Nos each bed room(total 4)

5 Table with chairs 1 table with 6 chairs

6.1.23 Lobby:-


1 Setty 2 set double and three single

2 Tea pot 1 No


APTDC


of 52

ANNEXURE- 10 (As per Drawing) 2


of 52

Four DOUBLE-BEDDED ROOM HOUSE BOAT – PRINCIPLE PARTICULARS All the below mentioned quantity are tentative/indicative and has to be as per actual requirement or as directed by the departmental officer.

Fore peak

Bed room with attached bath and toilet 4 Nos.

Crew toilet

Kitchen

Aft deck

Open Lounge 6.1.1 General Description:-




moulded out of best quality material recommended for standard marine construction.

• The super structure to be MS to create local area ambience.

6.1.2 Watertight compartments of Hull:-

The Hull to be of 6 compartments – Forepeak, Ford storage space, fresh water and fuel storage, waste


6.1.3 Main Engine:-

ALM 4 CTI with 2:1 Gearbox.

6.1.4 Fuel tank:- 1 No 300L fuel tank to be provided.

6.1.5 Bilge system:- A semi rotary pump to be provided at the Deck, ford and aft to bilge out the water from compartments.


of 52




system.








LED room



one in kitchen

7 Modular Power plug 5 A Bed Room 3 x 2 room

8 Modular Power plug 15 A Kitchen 2 Nos.

9 Modular Power plug 5 A Engine room 1 No.

10 Emergency light Galley Bed room, Galley 10/15 w LED 1

Forward & ER Ceiling 10/15 w LED 1

11 Havells/Crompton/Bajaj Fan 60 w Bed room 1 no in each bed room

12 Daikin/Mitshubishi/Ogeneral A/C 1.5 Ton

split with remote Bed room 1 no each bed room

13

Generator KVA Kirloskar Green

Engine room

1 No. to cater the full load/as per the direction of departmental engineer

All the below mentioned quantity are tentative/indicative and has to be as per actual requirement or as directed by the departmental officer.






of 52


2 Nos Fire Buckets




1 Life jackets Adult 15 nos

2 Life buoys 15 nos

All the below mentioned quantity are tentative/indicative and has to be as per actual requirement or as directed by the departmental officer.

6.1.11 Air conditioning unit:-

One split A/c (1.5 Tone) Daikin/Mitshubishi/O general with copper fins suitable to operate in sea weather


supply to be provided to Bed room. Each bed room – 01 (1.5 Ton capacity)

6.1.12 Generator:-

Kirloskar Green Generator to be provided to cater the full load as per the directions of the departmental

engineer

6.1.13 Inverter:-

One number , 1 KVA inverter to be provided.



water resistant parquets . Toilets to be tiled.

6.1.15 Canopy / super structure:-

The MS super structure to be designed as desired by APTDC. The successful bidder must submit the designs

along with material so that APTDC will select the designs to suit the ambience of the environment


Tables with chairs (set) to be provided. The floor of Dining / Lobby to be of hard wood panels. Table and

chairs to be of very high quality with state of art design as per the choice of the APTDCL. (Quantity will be

decided by the departmental engineer/officer


of 52

6.1.17 Bed room:-

The frame structure will be decided by department officer/engineer






4 Mini Freezer 1 No.

5 Ice box 1 No 100L

6 Electricals As per the drawing and requirement Make: Anchor Panasonic /Havells/

Legrand/as directed by departmental engineer




6.1.19 Toilet:-




of bed room


of bed room

4 Mirror 3 nos. (1 each)

5 Towel Holder, Jaquar make 3 nos. (1 each)

6 Soap tray, Jaquar make 3 nos.

7 Health faucet, Jaquar make 3 nos.


All the above mentioned quantity are tentative/indicative and has to be as per actual requirement or as directed by the departmental officer.

6.1.20 Fender:-



of 52







2 Hull Gel coat/As desired by Engineer




enamel

6.1.22 Bed room:-


1 Cot with 6” PU foam mattress 1 Nos in each bed room

2 Pillows with cover 4 Nos in each bed room

3 Wardrobe 1 No in bed room

4 Chair 2 Nos in each bed room

5 Table with chairs 1 table with 2 chairs in each bed

room

All the below and above mentioned quantity are tentative/indicative and has to be as per actual requirement or as directed by the departmental officer.

6.1.23 Lobby:- Sl. No Items Quantity

1 Setty 2 set double and Four single

2 Tea pot 1 No


APTDC


of 52

APTDC – RFP FOR PROCUREMENT OF HOUSE BOATSAPTDC – RFP FOR PROCUREMENT OF HOUSE BOATS Page 5 of...

Documents

Transcript of APTDC – RFP FOR PROCUREMENT OF HOUSE BOATSAPTDC – RFP FOR PROCUREMENT OF HOUSE BOATS Page 5 of...