APPLICATIONS Honda Civic 2006-2009 99-7871/ 99-7871T · • 70-1722 - Honda harness ... Dash...
Transcript of APPLICATIONS Honda Civic 2006-2009 99-7871/ 99-7871T · • 70-1722 - Honda harness ... Dash...
INSTALLATION INSTRUCTIONS FOR PART 99-7871
Small Flat Screwdriver • Phillips Screwdriver • Socket Wrench
1-800-221-0932 www.metraonline.com
KIT FEATURES
© COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
• DIN Head Unit Provision with Pocket• ISO DIN Head Unit Provision with Pocket• Double DIN Head Unit Provision• ISO Stacked Head Unit Provision• Stacked DIN Head Unit Provision• Painted To Match Factory Dash:
99-7871= Gunmetal, 99-7871T= Taupe
A) Radio Housing • B) DDIN Trim Plate • C) ISO Trim Plate • D) Double DIN Brackets • E) Pocket • F) (8) #8 Phillips Screws • G) ISO Brackets • H) (5) White Plastic Clips • I) (6) Metal Clips
KIT COMPONENTS
TOOLS REQUIRED:
A
APPLICATIONS
Honda Civic2006-2009
CB
E
D
F G
99-7871/99-7871T
WIRING AND ANTENNA CONNECTIONS(Sold Separately)• 70-1722 - Honda harness - 2006-up• 40-HD10 - Honda antenna adapter 2005-up
H
I
Dash Disassembly Honda Civic 2006-2009....................................................................... 1,2
Kit Assembly: DIN Head Unit Provision.......................................................................... 3ISO DIN Head Unit Provision ................................................................... 4Double DIN Head Unit Provision ............................................................. 5Stacked ISO DIN Head Unit Provision..................................................... 6Stacked DIN Head Unit Provision. .......................................................... 7
Final Assembly ....................................................................................... 8
99-7871
TABLE OF CONTENTS
KNOWLEDGE IS POWEREnhance your installation and fabrication skills byenrolling in the most recognized and respectedmobile electronics school in our industry.Log onto www.installerinstitute.com or call800-354-6782 for more information and take stepstoward a better tomorrow.
99-7871 DASH DISASSEMBLY
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Unclip and remove the panel belowthe steering wheel. (Figure A)
2
HONDA CIVIC 2006-2009
Remove the (1) Phillips screwexposed on the lower left side of thepanel above the steering wheel andaround the instrument cluster.(Figure B)
3
Unclip and remove the panel aroundtop of steering wheel and instrumentcluster. (Figure C)
4
Remove panel inside pocket belowradio and climate controls thenremove (2) 8 MM screws facing upbehind panel. (Figure D)
5
A
B
CD
1
99-7871 DASH DISASSEMBLY
Unclip and remove radio/climatecontrol assembly. (Figure E)
6
Remove the (2) Phillips screwssecuring the hazard switch to theradio/climate control panel. (Figure F)
9
Remove the (2) Phillips screwssecuring the passenger air bagon/off light to the radio/climate con-trol panel. (Figure F)
10
Remove (3) Phillips screws securingthe a/c vent to the radio/climatecontrol panel. (Figure F)
7
HONDA CIVIC 2006-2009
Remove the (4) Phillips screwssecuring the climate control to theradio/climate control panel.(Figure F)
8
E
8
8
8
8
7
7
7
9
9 10
10
REAR VIEW
F
2
3
NOTE: Secure the a/c vent, climatecontrol, hazard switch, and the pas-senger air bag on/off light into the99-7871 radio housing panel usingthe factory hardware. (FigureA1)Position the (6) metal factory retain-ing clips and (5) plastic white clipsonto the radio housing in the samelocation as the factory radio/climatecontrol panel. (Figure A2)
Slide the aftermarket head unit intothe cage and secure. (Figure D)
3
Slide the pocket into the bottom sec-tion of the kit housing. (Figure B)
1
Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs down. (Figure C)
2
DIN HEAD UNIT PROVISION
99-7871 KIT ASSEMBLY
CD
A1
BACK FRONT(6) METAL RETAINING CLIPS
(5)WHITE PLASTICRETAININGCLIPS
A2
B
4
Snap the Trim plate into the RadioHousing. (Figure D)
4
ISO DIN HEAD UNIT PROVISION
99-7871 KIT ASSEMBLY
NOTE: Secure the a/c vent, climatecontrol, hazard switch, and the pas-senger air bag on/off light into the99-7871 radio housing panel usingthe factory hardware. (Figure A1)Position the (6) metal factory retain-ing clips and (5) plastic white clipsonto the radio housing in the samelocation as the factory radio/climatecontrol panel. (Figure A2)
Slide the head unit into the radioopening until the side clips engage.(Figure D)
3
Mount the ISO Brackets to the headunit with the screws supplied withthe unit. (Figure C)
2
CD
BACK FRONT(6) METAL RETAINING CLIPS
(5)WHITE PLASTICRETAININGCLIPS
A1
A2
B
Slide the pocket into the bottom sec-tion of the kit housing. (Figure B)
1
5
Attach the corresponding bracket tothe DDIN head unit. (Figure C)
2
CD
Remove the center bar from the 99-7871 radio housing. (Figure B)
1
Insert the DDIN trim plate into theradio housing. (Figure D)
3
DOUBLE DIN HEAD UNIT PROVISION
99-7871 KIT ASSEMBLY
A1
BACK FRONT(6) METAL RETAINING CLIPS
(5)WHITE PLASTICRETAININGCLIPS
A2
BPosition the bracket/radio assemblyto the back of the radio housing andsecure with the (8) Phillips screwsprovided. (Figure D)
4
NOTE: Secure the a/c vent, climatecontrol, hazard switch, and the pas-senger air bag on/off light into the99-7871 radio housing panel usingthe factory hardware. (Figure A1) Position the (6) metal factory retain-ing clips and (5) plastic white clipsonto the radio housing in the samelocation as the factory radio/climatecontrol panel. (Figure A2)
6
Attach the corresponding bracket tothe (2) ISO head units. (Figure C)
2
D
1
Insert the DDIN trim plate into theradio housing. (Figure D)
3
Position the bracket/radio assemblyto the back of the radio housing andsecure with the (8) Phillips screwsprovided. (Figure D)
4
STACKED ISO DIN HEAD UNIT PROVISION
99-7871 KIT ASSEMBLY
BACK FRONT(6) METAL RETAINING CLIPS
(5)WHITE PLASTICRETAININGCLIPS
A
A2
B
C
NOTE: Secure the a/c vent, climatecontrol, hazard switch, and the pas-senger air bag on/off light into the99-7871 radio housing panel usingthe factory hardware. (Figure A1) Position the (6) metal factory retain-ing clips and (5) plastic white clipsonto the radio housing in the samelocation as the factory radio/climatecontrol panel. (Figure A2)
Remove the center bar from the 99-7871 radio housing. (Figure B)
7
Slide the aftermarket head units intothe cages and secure. (Figure C)
C
Slide the DIN cages into the RadioHousing and secure by bending themetal locking tabs outward.(Figure B)
1
2
STACKED DIN HEAD UNIT PROVISION
99-7871 KIT ASSEMBLY
A1
B
BACK FRONT(6) METAL RETAINING CLIPS
(5)WHITE PLASTICRETAININGCLIPS
A2
NOTE: Secure the a/c vent, climatecontrol, hazard switch, and the pas-senger air bag on/off light into the99-7871 radio housing panel usingthe factory hardware. (Figure A1) Position the (6) metal factory retain-ing clips and (5) plastic white clipsonto the radio housing in the samelocation as the factory radio/climatecontrol panel. (Figure A2)
8
FINAL ASSEMBLY1 Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections asshown. (Isolate and individually tape off the ends of any unused wires to preventelectrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.3 Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the headunit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individuallytape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-) . . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
99-7871 FINAL ASSEMBLY
9
99-7871
NOTES
99-7871 INSTRUCTIONS
1-800-221-0932 www.metraonline.comREV. 06/29/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST99-7871