ADB Remote Control How to program to control your TV ...€¦ · on the ADB remote blinks twice....
Transcript of ADB Remote Control How to program to control your TV ...€¦ · on the ADB remote blinks twice....
Code Search Method1. PRESS and release the TV button2. PRESS and HOLD the RCU SETUP until the TV button blinks twice3. Enter in 9 9 1 and the TV button will blink twice4. Aim the remote at the TV and press and release the POWER button5. PRESS and RELEASE the CH+ or CH- until the TV turns o�6. PRESS the POWER button to turn the TV on7. PRESS the RCU SETUP button to store the code for the TV. The TV button will blink
twice. The remote is now ready to operate the TV
Volume (Use with Code Search Method)1. Press and release the TV button2. Press and hold the SETUP button until the TV button blinks TWICE3. Enter in 9 9 34. Press and release the TV button and wait until it blinks twice
Once these steps have been completed, you should be able to control the volume +/- and the mute regardless of what “mode” you are in. (i.e. TV, STB)
The Learning Method
Basically, this means that you can transfer the information from the FACTORY ISSUED remote to the ADB remote (power, volume, etc.) It bypasses having to do the code search method.
1. Press the RCU SETUP until the last selected mode button blinks twice. (TV, DVD, etc.)2. Enter in 9 7 53. Press the TV button4. Press the button you wish to program (i.e. POWER) on the ADB remote5. Place the ADB remote and the ORIGINAL remote head-to-head about 2 inches apart.6. Press and HOLD the SAME button (power) on the ORIGINAL remote. The ADB remote TV button
will blink rapidly and turn o�. Keep holding the button on the ORIGINAL remote until the TV button on the ADB remote blinks twice.
*If the learning failed, the TV button will emit on long blink. You will have to repeat step 6.
Setting Up ADB Remote to Turn O� TV
Use the following steps to allow the ADB remotes to turn on/o� the TV while in Set Top Box (STB) mode. This should eliminate the need to toggle between TV mode and STB mode. You can determine what mode the remote is in as the LED mode light will flash when any button on the remote is pushed.
NOTE: With this setup, ONLY the TV power (on/o�) will be controled using the remote while in STB mode. The STB power will have to be toggled on/o� by pushing the power button located on front panel of the STB.
To control your TV power from STB mode:1. Push STB2. Press and hold RCU Setup until STB flashes twice3. Press 9 9 54. Press Power5. Press TV6. Press Power7. Press STB8. Press and hold RCU Setup until STB flashes twice
LYNXX Corporate O�ceCamp Douglas, WI
127 State Hwy 12 & 16 Phone: (608) 427-6515
Internet | Phone | TVADB Remote ControlHow to program to control your TV
LYNXX Corporate O�ceCamp Douglas, WI
127 State Hwy 12 & 16 Phone: (608) 427-6515
Internet | Phone | TVADB Remote Control Remote Buttons & Descriptions
POWERTurns components On/O�
TVControls TV functions
MENUDisplays main menu
OKPress when you want to select
a program or highlighted object
RED/GREEN/YELLOW/BLUE BUTTONS
For o�ce use only
INFODisplays information about the current program
PLAYBACK CONTROLSFor use with DVR/VOD functions
STBUsed for Set Top Box functions
PAGE BACK/FORWARDScrolls side-to-side from the
current page in the guide
GUIDEDisplays program guide
VOLUME +/-Volume control
NUMBER KEYSUsed for entering channel numbers
DELETEDeletes single character in
text entry boxes
INPUTSwitches between audio/
video inputs on your TV
ARROWSAllows you to scroll through the guide and menu
EXITExits the guide and menu
PAGE UP/DOWNScrolls Up/Down through the current page in the guide
CHANNEL +/-Changes channels on the STB
LASTReturns to the previous channel
CLOSED CAPTIONINGEnable/Disable Closed Captioning