PEC Visio Universal TV Remote Control

7/31/2019 PEC Visio Universal TV Remote Control

1/8

For better assistance on technical concerns, please call us on 413-9788, 362-0393, 362-1240 09236598857,

09222444303, or log on to www.cdrking.com and care to chat [email protected],

[email protected],[email protected].

Visio Universal TV Remote Control (RC-TV001-PEC)

(PEC Series)

Item Picture Specifications:

Works with: Major TV brands Batteries: 2 x AAA; 3V Range: up to 8 meters Dimensions: 47x160x20mm Weight: 62gms

Features:

Operates major TV control function Can adopt manual or auto code searching With LED light indicator Easy to operate Pre-programmed for easy setup Library includes thousands of model that are

not specifically identified

Package Content:

1 x Universal Remote Control

WARRANTY: 3 months free service warranty
mailto:[email protected]:[email protected]:[email protected]:[email protected]:[email protected]:[email protected]:[email protected]:[email protected]:[email protected]:[email protected]:[email protected]


2/8





3/8




Battery Installation

Open the battery cover, place 2xAAA batteries according to its polarity (+/-) inside the batterycompartment.

Cautions on Battery Use:

When the batteries are being replaced, the original setting will remain if no button on the remotecontrol is being pressed. Otherwise the original setting will be lost and you have to reset your device.

As our remote control of low power consumption, the batteries have 15 months service life undernormal conditions. However its service life may be shortened if used or operated improperly.

Do not use old and new batteries or batteries of different models at the same time. If battery leakage, take out the batteries, wipe the battery compartment clean and replace it with

new batteries.

If this remote control is intended to be not in use for a long time, please remove the batteries.


4/8




Setting the Remote Control

There are four methods (Methods A, B, C & D) provided to set this remote control, any of these methods

can be use to set the remote control.

A. Direct Code Entering:1. Switch on the TV to its panel and find the code on the code list that represents the brand of your TV.

2. Press & hold the SET and the POWER button simultaneously until the red LED indicatorilluminates then release the holding of the buttons.

3. Enter the 3 digit code of your TV model one by one.


5/8




4. Try if the remote control works properly. If not, repeat the setting procedures from step 2 then enterthe next code.

Note:

Due to too many codes corresponds to your TV model, you are recommended to set your TVcode by code and select one code that suits most to your TV.

B. Automatic Searching1. Manually turn ON your TV set2. Press & hold the SET button (LED Light flashes continuously) until the volume appears on the TV

set. When the volume icon appears on the TV screen, stop pressing the SET button

3. Check the function of the remote control if it works.C. Quick search

When the number cannot be found in the CODE LIST, you can find the suitable number through this

function.

1. Turn ON your TV Set2. Press SET button continuously and press the POWER button (the LED will turn ON). Once the LED

light lit-up. Stop pressing the buttons.

3. Press the volume + button until the VOLUME icon appears on the TV screen.


6/8




4. Press the SET button and the LED will turn off.5. Check the function of the remote control if it works.

D. Brand Search1. Turn ON your TV set2. Keep pressing the respective brand button of the remote control until the volume icon of your TV

appear, then stop pressing the button. For example the brand of your TV is PANASONIC, press thebutton number 7.

3. Check if the remote functions works.


7/8




FAQs

Note:

Features and functions may depend on various TV models. There may be functions that yourunit may not have.

Lock Function:

Press the OK button for about 3 seconds, the LED light flickers it means that the trademark code is

locked.

Unlock Function:

Press the NORMAL button for about 3 seconds then the LED light flickers it means that the trademark

code is unlock. You can search again.

My remote control is not working or only works when I am close to the television?Make sure you are using new batteries and that they are inserted correctly. Your remote will operate 16

ft. away from the television, and 30 degrees from center in either direction. Make sure you are operating

the remote on its range.

What should we do if the controlling distance becomes shorter than before? 1. The distance becomes shorter because the battery voltage is less than usually recommended. You must

put on a pair of new batteries.

2. Other internal components may cause the phenomenon of aging, if you put on a new battery and it still

cannot work better, please send the remote control to repair or replacement a new remote control.

How Do Universal Remote Controls Work?Universal Remote Controls are device s that is designed to operate multiple electronic devices from

different manufacturers simultaneously. A Universal Remote can be convenient if you have a TV from one

manufacturer.

If I take the batteries out, will it lose my settings?No. When you replace your batteries, your remote control is restored to its full functionally, complete

with your favorite settings.


8/8




Warranty

Warranty is VOID if the sticker is Missing/Broken/Tampered

PEC Visio Universal TV Remote Control

Documents

Transcript of PEC Visio Universal TV Remote Control