A5 Octavia Nexus NavigationSystem

7/30/2019 A5 Octavia Nexus NavigationSystem

1/51

kodaOctavia

SIMPLY CLEVER

RADIO NAVIGATION SYSTEM NEXUS


2/51

About this Owners ManualThis Owners Manual contains important information, tips, suggestionsand warnings on using the radio navigation system. The other OwnersManual in the vehicle wallet contain further information which you shouldbe aware of for your own safety and for the safety of your passengers.

Ensure that the complete vehicle wallet is always in the vehicle. This isespecially important when you lend or sell the vehicle to others.

This manual describes the scope of vehicle equipment at the time ofpublication. Some of the equipment described here will not be availableuntil a later date, or is available only in certain markets.

Illustrations may vary from your vehicle in details. For this reason youshould regard illustrations as a general guide.

Directions and positions (e.g. right, left, front, rear) are always relativeto the direction of travel of the vehicle unless otherwise stated.

Some sections of this booklet do not apply to all vehicles. If this is thecase, a text at the start of the section indicates to which vehicles itapplies, e. g. Applies to vehicles with CD changer.

Registered trademarks are marked. However, the absence of thissymbol does not constitute a waiver of the rights concerning any term.

The section is continued on the next page.

Indicates the end of a section.

WARNING

Texts with this symbol contain information on safety. They help

protect you from accidents and injury.

CautionTexts with this symbol draw your attention to potential sources of damageto your vehicle.

For the sake of the environmentTexts with this symbol contain additional information on the protection ofthe environment.

NoteTexts with this symbol contain additional information.


3/51

Contents 1

Contents

Quick Reference Guide . . . . . . . .

Control elements . . . . . . . . . . . . . . . . . . . . . . .Display elements on the screen . . . . . . . . .

Switching on and off . . . . . . . . . . . . . . . . . . . .

Radio/CD/Sound . . . . . . . . . . . . . . . .

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sound, sound focus and volume . . . . . . . . .

Navigation . . . . . . . . . . . . . . . . . . . . . . . .

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Destination entry . . . . . . . . . . . . . . . . . . . . . . .

Destination memory . . . . . . . . . . . . . . . . . . . .

Parameters for route calculation . . . . . . . . .

Map and symbol displays . . . . . . . . . . . . . . .

Route guidance . . . . . . . . . . . . . . . . . . . . . . . .

Information and systemsettings . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .

System settings . . . . . . . . . . . . . . . . . . . . . . . .

External units . . . . . . . . . . . . . . . . . . . .

Calling up external units . . . . . . . . . . . . . . . .

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

24

4

6

6

10

12

14

14

17

23

27

32

38

41

41

42

44

44

45


4/51

Quick Reference Guide2

Quick Reference Guide

Control elements

This overview will help you to quickly familiarise yourself with the control elements.

On/off knob (push) and volume control (turn). The volumecontrol will regulate the volume of the audio source currently

Fig. 1 Overview of the control elements

A1


5/51

Quick Reference Guide 3

selected. A column will indicate the volume level. Thevolume of a telephone conversation can also be regulatedusing the volume control.

Entries in the screen menus can be made using the menubutton. Turn to mark a function or a sub-menu. Press to

select a function or a sub-menu.Sound and sound centre settings . . . . . . . . . . . . . . . . . .

Left and right of the screen - 5 function/station keys.

The term function key is used because the keys havedifferent functions depending on the menu being shown inthe display. If the text says, for example, Press

, then press the function key next to wherethe text Dest. on map appears on the screen.

Station keys: The upper 6 function keys are used asstation buttons in the radio mode. Stations can be storedon these keys. The upper 6 function keys can be used toselect the inserted CDs in CD changer mode.

Backwards/forwards keys, apply to the active audiosource

press briefly: radio mode: station change in the memory;CD mode: changes track

press longer: radio mode: station change in the stationlisting; CD mode: fast forward/backward search

Switches between day and night display or darkens thescreen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Slot for an audio or navigation CD. . . . . . . . . . . . . . . . . . . .

CD eject button. The ejected CD will be pulled back intothe unit if it is not fully withdrawn within 10 seconds.

Set flagged destination. The unit will store the currentvehicle position when this button is pressed. When thisbutton is pressed again, the flagged destination will be over-written if it has not been stored in the destination memory. .

The traffic jam button calls up the input menu to excluderoute sections in a route list or to enter traffic jam informationmanually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Back to previous menu.

Map display when Navigation CD is inserted / Switch

to symbol display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Calls up the Navigation main menu. . . . . . . . . . . . .

Switches to other auxiliary audio or video units. . . . .

reserved for additional functions at a later date

CD and CD changer control 1) . . . . . . . . . . . . . . . . . .

Radio menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Call up system settings, traffic reports, positiondisplays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

WARNING

Adjust the volume so that you can still hear signals coming fromoutside the vehicle, such as fire brigade, ambulances or policecars.

CautionThe screen is not a touch screen. Do not press on the surface. The screencan be cleaned with a soft cloth (and alcohol, if necessary). Do not usesolvents such as turpentine or petrol to clean the surface as they willcorrode the material.

A2

A3 12A4

Dest. on map

A5

A6 42

A7 108

A9

17, 23

1) You will find a description in the corresponding Owners Manual.

A10

30

A11 ESCA12 MAP

39A13 NAVI 16A14 AUX 44A15 TELEA16 CD 10A17 RADIO 6A18 INFO

41


6/51

Quick Reference Guide4

Display elements on the screen

This section describes the elements seen in the display.

The functions or sub-menus shown on the screen can be called up bypressing the function key situated directly next to them. This can alsobe carried out by first turning the menu knob and then pressing it.

The orange selection box can be moved using the menu knob. It willdisappear from the screen if the unit is not used for 30 seconds andwill appear again if the menu knob is turned.

The selection of the function characteristics, such as destin. oroverview, can only be reached by pressing and turning the menuknob.

The right part of the status bar contains additional information or theoption back with ESC

Details of the active audio source or navigation status are shown inthe centre part of the status bar.

The left part of the status bar shows the current menu.

Below the status bar

An orange marking indicates which source is active. Press the keybeneath it to call up the main menu for this source.

A green marking indicates which source is still active in the background(the radio in this example). Press the key beneath it to call up the main

menu for this source.

If the text CD ? is displayed in the marking above the button, the CDinserted in the CD drive can not be read.

Switching on and off

A safety code made up of four characters must be entered

when switching on for the first time.

Switching on/off

Press the rotary/push knob page 2, fig. 1 .

Fig. 2 Displayelements

AA

AB

AC

AD

AE

F

CD

Fig. 3 Entering thesafety code

A1


7/51

Quick Reference Guide 5

Press the rotary/push knob again to switch the unit off.

Entering the safety code

The safety code can be found on the unit card.

Enter the characters by turning and pressing the menu knob page 4, fig. 3.

Press if you wish to change incorrect entries.

Once the safety code as entered corresponds to the codegiven on the unit card, press .

The last menu used and also the last audio source used before switchingoff will be selected automatically when the unit is switched on again. Theradio navigation system will be switched off if the ignition is turned off. The

unit can be switched on again using the rotary/push knob when the igni-tion is switched off. It will be switched off automatically after an hour tostop the vehicle battery from running down.

The following text might appear if there is no CD in the CD slot and thesafety code has been entered and you have pressed : No CD isinserted. Please insert a kodaAuto Navigation RNS CD.

If you do not wish to use the navigation system immediately, you can stillselect a different audio source by pressing the appropriate button.

Comfort Coding

If you have not received a security code for your radio, it means that yourcar is fitted with comfort coding system, which does not require a code. Incase of disconnection and reconnection of car battery, first switch on thepower by the starting key, then switch on the radio. If you need a code,contact your koda service.

NoteThe unit will be blocked for one hour if an incorrect code is entered threetimes. The code can be entered again after this one hour has elapsed.

OK

OK


8/51

Radio/CD/Sound6

Radio/CD/Sound

Radio

Overview

Information is given here on how to select and store

stations.

The following radio functions are selected via the function keys:

Scans stations or stores those stations with the strongestreception page 6, Scan/AS,

Calls up station list or manual frequency input page 8,Station selection from a list (FM only),

Sets the waveband and traffic radio, mute function page 7,Setting waveband/Muting,

Set-up for RDS functions page 9 Settings.

Scan/AS

The stations with the strongest reception are either

scanned or stored automatically.

Playing stations briefly Briefly press f ig. 5.

Autostore on the second memory level (FM2 or AM2)

Press for longer than 2 seconds to allocate thosestations with the strongest reception in the selected waveband(FM2 or AM2) to the upper 6 function keys.

Fig. 4 Radio mainmenu

Scan / _AS

List / _MAN

Band

Set-up

Fig. 5 Autostore AS

Scan / _AS

Scan / _AS

R di /CD/S d 7


9/51

Radio/CD/Sound 7

Autostore for all memory levels (Initial Autostore)

Press for longer than 10 seconds to allocate thosestations with the strongest reception in all wavebands to theupper 6 function keys.

The selected function will be shown on the screen and can be stopped bypressing again.

A scan in the FM waveband will play through the list of registered stations.A scan in AM will play all stations with a high quality reception. Eachstation scan lasts 8 seconds. Press the menu knob or if youwould like to stop at the station currently being played.

NoteUse the function Initial Autostore if you are using the unit for the first time

or when selecting new stations in the waveband. Any station names on thestation keys will be overwritten. The process of searching for and storingthe station names takes a few seconds.

Setting waveband/Muting

Press in the radio main menu page 6, fig. 4 to seethe frequencies.

Press or to receive VHF stations.

Press or to receive medium wave stations.

When in FM1 or FM2 mode, press to receive traffic infor-mation reports.

Press / to mute the radio or to switch themute function off/on.

The last heard station will be played for the waveband selected. Trafficinformation reports will be relayed even when the radio has been muted.The TP function must be active for this purpose (white column next to thefield). When TP is active, the letters TP are lit up in orange. The increased

Scan / _AS

Scan / _AS

Scan / _AS

Fig. 6 Radio waveband

Band

FM1 FM2

AM1 AM2

TP

Radio off Radio on

Radio/CD/Sound8


10/51

Radio/CD/Sound8

volume level for the traffic announcement can be lowered by pressing thebutton .

Station selection from a list (FM only)

The radio navigation system will automatically compile

and store a list of receivable FM stations after the unit is

switched on.

Press in the radio main menu page 6, fig. 4 to

see the stored stations.

Select a station by turning and pushing the menu knob or byusing the right-hand function keys.

Select a station from the list by turning and pushing the menuknob. You can scroll through several pages of the list using thescroll markers , , and and confirm your selectionby pressing .

You can also select the stations stored in the list by pressingthe button or for more than 2 seconds.

Station selection from memory or by enteringfrequency

Station selection from memory

Briefly press button or to listen to the stored station.

Station selection by entering frequency

Press the button page 2, fig. 1 and hold itpressed for more than 2 seconds. As soon as the informationregarding the frequency appears with an orange frame andthe word manual in the middle of the display, you can manu-ally enter the frequency. The station finding starts in theselected direction in steps of 0.1 MHz (FM) or 9 kHz (AM). Youcan set in this way one of your known station frequencies. Youcan also change the frequency by turning the menu knob.

For fine tuning press the button or .

INFO

Fig. 7 List of stations

List / _MAN

OK

List / _MAN A5

Radio/CD/Sound 9


11/51

Radio/CD/Sound 9

Allocating the stations to the station buttons

Stations can be allocated to the buttons to make it easier

to select them quickly.

Press one of the upper 6 station buttons until you hear a signal page 2, fig. 1 . The station you are listening to is nowstored on the button.

A total of six stations can be stored on the station buttons for each mode;FM1, FM2 or AM1 or AM2. The short form of the station name or thestation frequency will appear next to the button. Press one of the buttonsif you wish to listen to one of the stored stations.

Note

The memory on a button will be overwritten if a new station is storedthere.

RDS settings

Some stations transmit text and information in addition to

the station name.

Press in the Radio main menu page 6, fig. 4.

Further text information as running text will not be displayed on thescreen, in addition to the station name, for all RDS stations.

A tick will indicate which options have been selected.

Function keys

fixed: Only the station name will be shown.

variable: Text information is shown as running text.

autom.: The selected regional programme of a stationbroadcasting over a wide area will continue to be displayed even when

A4

Fig. 8 RDS functions

Set-up

RDS Name

RDS Regional

Radio/CD/Sound10


12/51

Radio/CD/Sound10

you enter the broadcasting area of another regional programme of thesame station.

page 42

WARNING

Your attention must, however, always be concentrated on roadtraffic as an absolute priority. Do not allow yourself to be distractedby the RDS running text.

CD

Listening to an audio CD

Listening to a CD

Press the button page 2, fig. 1. If a CD is already in theplayer, the last played track will be selected. Otherwise thefollowing will appear briefly on the screen: No Audio CD.

Insert a standard 12 cm audio CD. The play function will startautomatically.

Playing the previous or next track

Press button or briefly.

Fast forward/reverse

Press and hold button or .

Ejecting a CD

Press page 2, fig. 1 .

The number of the track and its length are shown on the screen. TP lightsup in orange if traffic reports are to be received and TMC indicateswhether TMC stations are being received fig. 9.

Function keys during the play function:

... Selects the corresponding CD in the CD changer ifconnected 2).

Selects the CD that is in the unit.

All tracks on the CD will be played for 8 seconds at a time.

The tracks on the CD will be played in a random order.

page 42

Syst. settings

Fig. 9 Main menu CD

2) You will find a description in the corresponding Owners Manual.

CD

A8

CD1 CD6

Int. CD

Scan

Mix

Syst. settings

Radio/CD/Sound 11


13/51

Radio/CD/Sound 11

WARNING

The CD player is a class 1 laser product. If it is opened, or is faultyor damaged, there is a risk of invisible laser beams escaping fromthe unit. The CD player contains no parts that have to be serviced.

Any repair work that needs to be done should, therefore, be carriedout by koda Service exclusively.

Caution Only 12 cm standard CDs should be used, not 8 cm single CDs. Onlyround CDs should be inserted in the CD slot. Special shape CDs can notbe played and they will damage the CD player.

Slide the CD with the printed side up into the CD slot up to the pointwhere it is drawn in automatically. Hold the CD at the sides. Avoid leavingfingerprints on the CD. Clean the CD with a dry, lint-free cloth. When doing

this, wipe the CD from the centre outwards. Do not clean the CDs usingalcohol or solvents. Do not place the CDs near heat sources or in thedirect sunlight. Do not write on the CDs and do not attach stickers to them.

Note The upper 6 function keys are only active if a CD changer has beenconnected.

CD-R and CD-RW formats can also be played, depending on thequality of the blanks.

If the text CD ? is displayed in the small marking above the button,the CD inserted in the CD drive can not be read.

Applies to vehicles: with CD changer

Playing a CD from the CD changer

How to use the radio navigation system to select a CD in

the CD changer.

Use the function keys to to select a CD from thechanger.

Uneven road surfaces and strong vibrations may cause the CD to jump.The CD play function should be switched off in this case.

CD

Fig. 10 CDs currentlyin the changer

CD1 CD6

Radio/CD/Sound12


14/51

Radio/CD/Sound12

Sound, sound focus and volume

This section describes how the sound character and the

volume of different sound sources can be set individually.

Press the button page 2, fig. 1 to open the Soundmain menu.

Function keys in Sound main menu:

or Treble or Bass settings fig. 11

3) Volume setting for the mid-range frequencies

Sound focus setting left/right

Sound focus setting front/rear

Opens the volume set-up where individual volume settings canbe made for the different audio sources fig. 12.

Function keys in the volumes set-up function:

The setting for the sensitivity of the speed-dependent volumeadjustment (GALA). The volume of the audio source will be increased

automatically by GALA as the road noise increases at higher speeds. Thevolume will be increased more the further the control is set towards theright.

Minimum volume for traffic announcements

Minimum volume for telephone conversations

Minimum volume for navigation system announcements

The traffic announcements are muted as long as a orangebar can be seen next to the function key.

Sets the minimum volume for when the unit is switched on.

NoteBy pressing buttons page 2, fig. 1 , and status button

at the same time, you can reset the radio navigation system to the

Fig. 11 Sound mainmenu

Fig. 12 Volumesettings

3) Vehicles with a sound system

A3

Treble Bass

Mid

Balance

Fader

Volume

GALA

TA Min

Telephone

NAV Min

NAV mute

Initial volume

A3 TELE A15A10

Radio/CD/Sound 13


15/51

factory settings. The message, Default settings being made. Pleasewait! is shown.

Navigation14


16/51

Navigation

Overview

How does the navigation system work, and how is itoperated?

An optimal route is defined using sensors, satellites and

traffic reports and the driver is then guided to his or her

destination.

The current vehicle position is determined using a system of satellites(GPS - Global Positioning System). Sensors in the vehicle measuredistances that have been driven. Measured values are compared using

the detailed map material on the navigation CD and corrected with theassistance of TMC traffic announcements as necessary. An optimal routeto the destination is determined in this way.

Navigation announcements and direction arrows shown on the screenand in the combi-instrument guide you safely and conveniently to yourdestination. You can drive to a given address in towns you are unfamiliarwith, or drive to the nearest garage or be guided to a hotel.

In this chapter, answers can be found to the following questions:

What rules do I have to keep to when using the navigation system?

page 14, Safety How do I use the navigation CD? page 15, The navigation CD

Can I listen to music when using the navigation system? page 15,General notes

What happens if I leave the recommended route? page 15,General notes

Can a navigation announcement be repeated? page 39,Announcement of navigation recommendations

How does the radio navigation system respond when driving in anunderground car park or a tunnel? page 15, General notes

How do I enter destinations? page 17, Destination entry

How can I enter garages, restaurants or hotels as destinations? page 21, Special destinations close to the address

Can I store destinations in a memory? page 23, Destinationmemory

What parameters can I set for route calculation? page 27, Param-eters for route calculation

What can I see on the screen? page 32, Map and symbol displays

Can I stop the route guidance function before I reach my destination? page 38, Route guidance

Safety

The navigation system determines the position of the vehicle, the directionand distance and the route to a selected destination without taking trafficregulations into account. Navigation recommendations are given asannouncements by the system. Direction arrows are also shown on thescreen. The destination is entered when the vehicle is stationary. Theroute guidance function is designed for cars and is thus unsuitable forlarger commercial vehicles.

Navigation 15


17/51

WARNING

Please observe the laws of road traffic legislation whenfollowing the recommendations made by your navigation system.

Route guidance is subject to constant changes despite the

information about one-way streets, pedestrian zones etc. stored onthe navigation CD. Information on traffic lights, stop and right ofway signs, parking and stopping restrictions as well as laneconstrictions is not included in the navigation system. Traffic signsand legislation always have priority over the recommendationsmade by the system.

Adjust your speed to suit road traffic conditions and alsoweather and visibility conditions. Do not drive faster in fog, forexample, if the navigation system tells you to do so.

The navigation CD

Inserting the navigation CD

Press the button page 2, fig. 1 to eject any CD in theCD slot.

Remove the CD and insert the navigation CD with the writtenside facing up.

Push the CD into the slot until the radio navigation systempulls it in. The program stored on the navigation CD is loaded.Do not remove the navigation CD before the loading processis finished.

The navigation CD contains a digitalised road map. The extent to whichsmall villages, streets and house numbers are contained on the CDdepends on the CD version.

The content of the CD is constantly being updated. You will receive infor-mation on new updates at your next koda Service. You will need a new

navigation CD for every country that you travel to.

NoteIf the text CD ? is displayed in the small marking above the button,the CD inserted in the CD drive can not be read.

General notes

You can continue to listen to the radio or CD (via the CD changer) whilstyou are being guided to your destination.

When entering an address (town, street), only those letters or symbolswhich make up a logical entry will be presented. A list of possible nameswill be shown. Do not forget to enter the blank space in names made upof more than one word, such as High Wycombe.

The route will be recalculated if you leave or disregard the route that wasoriginally calculated. This process takes only a few seconds.

The last announcement made can be repeated. The volume of a naviga-tion recommendation can be changed whilst it is being made.

A variety of different information on the route can be called up duringactive route guidance. The scroll function can be used to page throughlists shown on the screen, either line by line or page by page.

If the display Off Road appears on the screen, it means you are locatedon a non-digitalised street, e.g. on a farm track. The GPS satellites will notbe able to reach your antenna when you are in a tunnel or underground

A8

CD

Navigation16


18/51

garage, meaning that the unit orientates itself via the wheel sensors. If youtry to carry out a route calculation in this situation you may hear theannouncement: You are located on a non-digitalised street. Drive on untilthe display Off Road disappears.

Main menu - Navigation

Press the key to enter the Navigation main menu page 2, fig. 1 .

Function keys in the Navigation main menu Starts route guidance to the entered destination. Pressing

this button again will stop the route guidance function page 38, Routeguidance.

Field for entering your destination page 17, Destinationentry

Field for entering a stopover destination. A stopover destina-tion is entered in the same way as a destination. A stopover destination isdeleted from the screen as soon as it has been reached. It will, however,remain in the memory Last dest. page 17, Destination entry. If thestopover destination is reached, you will be informed that you havereached your destination, and route guidance to the final destination is

started automatically. If the stopover destination is not reached exactly,e.g. because it is not located directly on a road, you will be informed thatyou have reached the destination area. Route guidance to the next desti-nation is not started automatically.

Defines the parameters for route calculation page 27,Parameters for route calculation.

Enter your location manually or start a demonstration page 28, Settings.

Fig. 13 Main menuNavigation

NAVI

A13

Start route gd.

Destination

Stopover

Route opt.

Set-up

Navigation 17


19/51

Destination entry

Starting destination entry

Two addresses can be entered for the route calculation;

the address of the destination and the address of the stop-over destination.

Press the key to enter the Navigation main menu page 2, fig. 1.

Press or in the Navigation main menu page 16, fig. 13 to select between the destination entryoptions.

You will see a message that states that a destination has not yet beendefined if the destination is being entered for the first time. The last useddestination will be displayed if a destination has already been entered.

There are various methods of entering a destination or a stopover desti-nation. The procedure for entering the stopover destination is the same asfor the destination.

Enter the destination using town and street names page 18, Entering a new address (town, street, house number).

or Select a destination from a list of destina-tions that have already been stored page 19, Last destinations.

Fig. 14 Destination

Fig. 15 Stopover desti-nation

NAVI A13

Destination Stopover

New Address

Last dest. From dst. mem.

Navigation18


20/51

Enter a restaurant, a garage, an airport, border crossingetc. as a destination page 21, Special destinations close to theaddress.

The position were you were located when you lastpressed button page 2, fig. 1 is entered as the destination.

Mark your destination on a map using a crosshair page 21, Destination on the map.

Enter the longitude and latitude of a destination page 22, Position destination.

Select a destination from the travel guide. A travel guideis only available on certain navigation CDs. Further search functionsdepend on the content of the travel guide.

Store, delete or edit destinations in the destination memory page 23, Destination memory.

Deletes the entered stopover destination.

Entering a new address (town, street, house number)

Press , or to enter the nameusing the letter selection function.

Special dests.

To flagged dst.

A9

Dest. on map

Position dest.

Additional De...

Edit memory

Del. stopover

Fig. 16 Entering a newaddress

Fig. 17 Entering atown name

Town Street House number

Navigation 19


21/51

Enter the letters or numbers by turning and pressing the menuknob.

You will see a list of names or numbers in the lower half of thescreen. Press to enter the list.

Select a name from the list by turning and pushing the menuknob. You can scroll through several pages of the list using thescroll markers , , and and confirm your selectionby pressing .

Press to select a special destination close to thedestination address (town, street etc.) that you have alreadyentered.

and mark characters and deleted characters.

will display language-specific characters as necessary.

The term Town is used regardless of how many people live there. Botha village of 100 inhabitants and a city with 1 million are named as towns.A list of names to choose from will appear for town names which are usedmore than once. The system will automatically switch to street entry aftertown entry and then to house number entry. The centre of the town will beoffered as a destination if the town is so small that none of the streets havebeen digitally mapped.

The keys and will not be active if a town name hasnot been entered.

NoteEnter an intersection and house number as described.

Last destinations

The last destinations that have been used will be stored

automatically.OK

OK

Close to addr.

Street House number

Fig. 18 Last destina-tions

Fig. 19 Deleting lastdestinations

Navigation20


22/51

Making a selection from the last destinations

Press page 17, fig. 14 to make a selection fromthe list of the last used destinations page 17.

Turn the menu knob to make a selection from the list of the lastused destinations page 19, fig. 18. Press to make anaddress fully visible if it cannot be read fully.

Press the menu knob to select the address marked in orange.The Navigation main menu will appear with your selectedaddress after a few seconds.

Deleting the list of last destinations

Starting in the Navigation main menu page 16, fig. 13pressthe following function keys: , and

.

Select or when confirmation is asked for. Ifyou select , all of the last destinations, including thecurrent destination, will be deleted.

The addresses collected in the Last dest. memory can only be deleted allat once, not individually.

A total of 14 last destinations can be stored in the memory. A destinationwill not be stored in Last dest. until route guidance has started. If you arenot able to store any more destinations, the destination memory is full.Delete either the last destinations memory or destinations from the desti-nation memory page 26.

Addresses from the destination memory

Press page 17, fig. 14 to see a list of thestored destinations.

You can move a orange column by turning the menu knob.Press to make an address marked in this way fully visible ifit cannot be read fully.

The address marked in orange will be activated if the menuknob is pressed. The Navigation main menu will appear withyour selected address after a few seconds.

You will be shown a message if the destination memory is full. Some ofthe destinations should then be deleted manually.

Last dest.

Destination Edit memoryDelete last dest.

Cancel DeleteDelete

Fig. 20 Completedestination address

From dst. mem.

Navigation 21


23/51

Special destinations close to the address

Special destinations close to the destination can be

selected from a list.

Press page 18, fig. 16 to select a specialdestination close to the destination address (town, street etc.)that you have already entered.

Special destinations of the same category, e.g. restaurants, will bedisplayed in a list. The nearest destination will be shown in the first posi-tion.

Note If you have not changed your destination address entry, the area closeto this last destination will be analysed and the special destinations therewill be listed.

The type and number of special destinations will be determined by thecontent of the Navigation CD.

Destination on the map

A crosshair can be used to mark a destination on the map.

Press page 17, fig. 14 .

Use the right-hand function keys to move the crosshair to yourrequired destination.

Use or to alter the scale to suit your search strategy page 33, Changing the scale.

Fig. 21 Special desti-

nations close to theaddress

Close to addr. Fig. 22 Destination onmap

Dest. on map

Navigation22


24/51

NoteThe next section of the map will be shown after a few seconds when thecrosshair is moved to the side of the screen.

Position destination

A destination can be entered using the exact coordinates

for longitude and latitude.

Press page 17, fig. 14 if you want to enteryour destination using coordinates.

Turn the menu button to set the figure.

Press the menu knob. The orange square will disappear anda orange frame appears.

Move the orange frame to the arc minutes and then to thehundredth of an arc minute.

Press the menu knob again and enter the required figure.

Great Britain, for example, lies between 50 and 59 northern latitude and

2 and 8 eastern longitude. The route guidance function cannot bestarted if the figures entered are not within this area and the navigation CDfor Great Britain has been entered. Use the following data to estimate theposition of your location:

for latitude, 1 corresponds to approximately 111 km, 1 arc minute approx-imately 1.85 km and 1 hundredth of an arc minute approximately 18.5 m

for longitude, 1 corresponds to approximately 69 km, 1 arc minuteapproximately 1.15 km and 1 hundredth of an arc minute approximately11.5 m

NoteIf you set the longitude higher than 180 or lower than 0, the E will bereplaced by a W (western longitude). Latitudes can be set from 90N via0 to 90S and back only.

Fig. 23 Position desti-nation

Position dest.

Navigation 23


25/51

Destination memory

Storing destination, stopover destination, flaggeddestination or location

Storing the different destinations means giving them aname and storing them in the radio navigation system.

After entering a new address, press (starting from the Naviga-tion main menu) page 16, fig. 13 , .

Press to open the letter input menu.

Enter a name for your destination, e.g. Mr. Smith or Holidayhome.

Press to save the destination with the name.

The destination can now be called up f rom the memory as you need it. Thename should be short and clear. You can also use the names that aresuggested.

You enter the destination name in the same way used for entering a streetname page 18.

Fig. 24 Editing thememory

Fig. 25 Storing thedestination

Destination Edit memory

Save dest.

OK

Navigation24


26/51

Renaming destination

Starting in the Navigation main menu page 16, fig. 13pressfollowed by then

.

Turn the menu knob to move the orange bar to the name thatyou wish to change.

Press the menu button to call up the entry function for theletters.

Edit the name

page 18. If, however, you wish to keep the original name and not the

new one, press the button page 2, fig. 1 . Youralterations will not be stored.

Fig. 26 Renaming adestination

Destination Edit memoryRename destination

ESC A11

Navigation 25


27/51

Sorting destinations

The various different addresses in the destination memory

are stored chronologically according to their entry date

and can be sorted at a later date according to your require-

ments.

Starting in the Navigation main menu page 16, fig. 13pressfollowed by then .

Turn the menu knob to move the orange bar to the destinationthat you would like to move to another position.

Press the menu knob. Sort: Store now appears at the top ofthe screen. You can now move the address up or down byturning the menu knob.

Press to store the address in the new position. Sort:Select now appears again at the top of the screen.

Press the button page 2, fig. 1 to close the sortfunction.

The other destinations will be moved down if you move a destination to aposition that is already occupied.

Fig. 27 Sort: Select

Fig. 28 Sort: Store

Destination Edit memory Sort destinations

OK

ESC A11

Navigation26


28/51

Deleting individual destinations or the entiredestination memory

You can, in contrast to the "last destination" memory,

delete individual destinations from the destination

memory.

Deleting an individual entry

Starting in the Navigation main menu

page 16, fig. 13 pressfollowed by then .

Turn the menu knob to move the orange bar to the destinationthat you would like to delete and then press the menu knob.

When asked for confirmation, press . If you do not wishto delete the destination, press .

Deleting the entire destination memory

Starting in the Navigation main menu press

followed by then .

When asked for confirmation, press . If you do not wishto clear the destination memory, press .

Fig. 29 Deleting desti-nation memory

Fig. 30 Selecting entryto delete

Destination Edit memory Delete destination

DeleteCancel

Destination

Edit memory Clear dest. memory

DeleteCancel

Navigation 27


29/51

Parameters for route calculation

Route options

Press in the Navigation main menu page 16,fig. 13.

A short route might be quicker for your purpose in larger towns or citieswhere there are a lot of traffic jams. Route options can be altered whilstthe route guidance function is active. The changed parameters will be

used as a basis for the calculation of the remaining journey.

Function keys in the route option menu

fast orshort: Determines whether a fast or short route should becalculated.

dynam.: Dynamic route guidance responds to traffic reports broadcastby TMC stations. This function will automatically guide you round trafficjams or blocked roads.

, or Determines whether motorways, ferries or tollroads should be used. These options will, however, be used for calculationif there is no other logical route to the destination (e.g. an island is to beused without using a ferry).

Stores the selected settings for future route guidance usage.

Dynamic route guidance

An announcement that there are traffic jams on your route will be made ifa traffic jam is registered. You will also be warned directly before the trafficjam itself.

Once the dynamic route guidance function has been activated you will beinformed that the route is being recalculated due to traffic problems if anyhave been registered.

Traffic problems are indicated by a symbol on the map:

Fig. 31 Route options

Fig. 32 Symbols fortraffic problems

Route opt.

Route

Motorway Ferry Toll

by default

Navigation28


30/51

Traffic jam page 27, fig. 32

Slow-moving traffic

Road closed

The navigation system will calculate the quickest possible route when thedynamic route guidance option is active. The system might well guide you

through a traffic jam if the diversion would be longer.

Note The dynamic route guidance option will only function if you arereceiving at least one TMC radio station.

The radio navigation system will automatically look for a new TMCstation if you leave the reception area of the one you are using. The stationyou are listening to, however, does not have to be a TMC station.

The dynamic route guidance option will always use motorways, ferriesand toll roads.

The quality of the dynamic route guidance depends on the informationcontained in the traffic announcements. The radio stations broadcastingthis information are responsible for the content.

Settings

The vehicle position can be entered manually and you can

then start a demonstration journey.

AAAB

AC

Fig. 33 Settings in theNavigation main menu

Fig. 34 Positionsettings

Navigation 29


31/51

Entering your position

Press in the Navigation main menu page 16, fig. 13to enter the vehicle position.

Press . The entry window for the townappears. The entry for the street is made after you make your

entry and confirm it with . After confirming the name of thestreet you will see a list of the streets which have an intersec-tion with the named street.

Select the intersection and confirm your choice by pressingthe menu knob.

Now enter your position either before or after this intersectionin metres and also enter the direction of travel using the pointsof the compass.

Confirm your entry by pressing . The screen display willreturn to the Navigation main menu.

Entering your position on the map

Press and then to see your set positionon the map. The scale of the map can be altered using the twotop left-hand function keys.

Press the button page 2, fig. 1 twice to return tothe Navigation main menu.

Starting the demonstration

Press and then select active. The navigation system isactivated.

The radio navigation system will now travel along the routevirtually from start to finish if the route guidance function isstarted. You can listen to announcements and look at displays.

The navigation system will need some time for an exact definition of yourposition if you have transported your vehicle using the train or a ferry. Your

position can be entered manually if the automatic definition is notsuccessful.

The manual position input can be used to calculate a route between anytwo points regardless of where the vehicle is actually located.

Set-up

Position location

OK

OK

Set-up Position map

ESC A11

Demo

Navigation30


32/51

Manually excluding stretches of the journey

Stretches of the journey ahead and/or parts of the route list

can be blocked manually.

Menu for blocking and traffic jams

Press the traffic jam button page 2, fig. 1 if you want toblock a stretch of the route ahead.

Entering traffic jam information

Press fig. 35. Turn the menu button to enter the length of the traffic jam.

Press the menu knob. The display will be switched to the map.You will hear an announcement The route is being calcu-lated. The excluded stretch of the route will be shown as adotted blue line on the map.

Press Cancel exclusion option to include this stretch of theroute in the navigation option again.

Blocking part of the route list

Press . You will see a part of your route list.

Using the menu knob, move the orange bar to a line that startswith + or-. The stretches of the route are broken down intosections and can be opened or closed by pressing or .

Turn the menu knob to move the orange bar to the start of thesection that you wish to exclude from the navigation. Press themenu knob. The entry is now green.

Fig. 35 Blockage andtraffic jam

Fig. 36 Blocking astretch of the journey

A10

Congest. ahead

Enter exclusion

Navigation 31


33/51

Turn the menu knob. All stretches of the route that are blockedwill appear in green. Press the menu knob once you havemarked the route section in question. The display will beswitched to the map. You will hear an announcement that theroute is being calculated. The excluded stretch of the route willbe shown as a dotted blue line on the map.

Press to delete the blocking function.

You will be guided through a blocked area if there is no logical alternativeto travelling through it.

NoteIf you use a map CD which contains only major routes, you will have lessalternative routes than if you use a CD which contains minor roads. Toensure that you do not have to make unnecessary detours, you shoulduse a map CD containing all roads when you wish to be guided aroundcongestion on the route.

Cancel exclusion option

Navigation32


34/51

Map and symbol displays

Information in the map and symbol displays

Information on the route will be shown in the map or

symbol displays if the route guidance function is active.

Press the button page 2, fig. 1 . The screen willswitch between map and symbol displays.

Map display

Autozoom active ( in orange). The scale of the map will, forexample, be larger for motorway driving and more detailed whenmaking a turn.

Journey time or arrival time

Distance to destination or stopover

Road name

Vehicle position - The black arrow points in the direction of travel. Theroute ahead is shown as a blue line.

Route options and TMC:

If the dynamic route guidance option is active, the horizontal arrowis shown with a D, and blocked roads are shown as .

Fig. 37 Map display

Fig. 38 Symbol display

MAP A12

AA

B

ACAD

AE

AF

Navigation 33


35/51

TMC: The number of TMC reports received is shown by the blackdots.

Map scale

North

Traffic problems are indicated by a symbol on the map:

slow-moving traffic traffic jam

closed road

Symbol display

The number of GPS satellites

Route option (in this example dynamic route guidance D)

Arrival time or journey time

Distance to destination or stopover

Turn arrow, above it the name of the street you are turning into.Current road

The proximity bar shows how far away the turning point is. Thedistance to the next change of direction will be shown in the displayafter you have turned.

Changing the scale

You can choose from a total of 13 different scales.

Press or .

More details. A scale display appears in the top left-hand cornerwhen the button is pressed fig. 39

Large overview. A scale display appears in the top left-hand cornerwhen the button is pressed.

The selected scale will be shown once the menu knob is pressed or after3 seconds.

AGAH

AAABACAD

AEAFG

Fig. 39 Changing thescale

Navigation34


36/51

Changing display options

The map type and display can be selected, although some

settings cannot be seen until active route guidance has

started.

Press page 32, fig. 37 to change the display options.

location Shows your position on the map.

destin. Shows the area surrounding your destination.

overview Shows the entire route.The map will always be shown in the direction North at the top if you havechosen the map type overview ordestin.. In the map display option auto,a detail map (up to 2 km per cm) with the direction of travel at the top andan overview map (as of 5 km per cm) with North at the top will be shown.

auto The system selects the map display.

travel The display always adjusts to the direction of travel.

north North is always at the top of the display.

high Smaller scales are given priority for the automatic scale selec-

tion. low Larger scales are given priority for the automatic scale selection.

The settings forAutozoom will only take effect if is pressed in the mapdisplay page 32, fig. 37 .

travel t. Shows the remaining travel time.

arrival Shows the estimated arrival time page 32, fig. 37 .

Fig. 40 Displayoptions

Map type

Alignment

Autozoom

AA

Time format

AB

Navigation 35


37/51

Traffic reports display

Short texts of traffic reports that have been received can

be called up from a list.

Press in the map display page 32, fig. 37.

Or press and .

Turn the menu knob to move the orange bar to the trafficreport you are interested in.

Press to see the full text of the traffic report.

Moving the map section using the crosshair

Press in the map display page 32, fig. 37 to call up theshift function.

Using the right-hand function keys or by turning/pressing themenu knob, move the the crosshair to the destination of yourchoice.

Use the scale modifications to adapt the display to suit yourrequirements page 33.

The neighbouring map section will be displayed if you move the crosshairto the side of the screen. This procedure can take some seconds.

Fig. 41 Traffic reports

INFO Travel info

Fig. 42 Crosshair

Navigation36


38/51

Augmenting map contents

A range of symbols can be used to display additional map

content.

Press in the map display page 32, fig. 37.

Turn the menu knob or use the right-hand function keys tomove the orange bar to the map detail you are interested in.

Press the menu button or . A "tick" will appear next to themap detail.

NoteYou can lose the overview of the map if too many map details areselected.

Route list

The route list is a list of all route sections which will be trav-

elled through with active route guidance.

Press in the map display page 32, fig. 37 to see theroute sections of your current journey.

The route list is updated during the journey. It shows the roads that youhave not yet reached. Route sections that you have already travelled willbe deleted from the route list.

NoteIt takes some seconds after route guidance has started for the route list tobe compiled so that it can be displayed.

Fig. 43 Map contents

OK

Fig. 44 Route list fromthe map

Navigation 37


39/51

Position display

The current information on the position of the vehicle is

shown here.

GPS status (number of satellite receptions, positioning mode)including the direction and distance to destination (with active routeguidance).

Direction of travel

Altitude (GPS altitude). If too few satellites are received to calculatethe altitude, the display is green.

GPS position (longitude)

GPS position (latitude)

The direction of travel is shown in degrees and also in the form of acompass.

The GPS status shows the number of satellites as dots and also showsthe positioning mode (NO FIX, 2D FIX, 3D FIX).

NO FIX The GPS reception is not sufficient to fix the position of thevehicle.

If the position definition forNO FIX is only possible using the wheelsensors (underground garage etc), the GPS coordinates will be displayedin green. The GPS coordinates will no longer be shown following a longdistance with NO FIX in the display or if it is not possible to determine the

position. 2D FIX The horizontal position of the vehicle can be determined, butnot the altitude (altitude display is green).

3D FIX Position and altitude can be determined.

The altitude given is accurate to 15 m at altitudes between 0 m and+5000m. The system will be less accurate if the GPS reception is bad orweather conditions are poor.

The direction to the destination is shown in the form of a marking outsidethe compass. If the destination is not in the area displayed by the compass(i.e. to the side or behind the vehicle), the marking is shown as an arrowto the side in question.Fig. 45 Positiondisplay

AA

AB

AC

Navigation38


40/51

Route guidance

Starting/stopping route guidance

Press . You will hear an announcement that theroute is being calculated. The radio navigation system willautomatically switch to the map display.

Press the button to return to the Navigation main menu.

Press if you wish to stop the route guidancefunction before you have reached your destination.

The route guidance function can only be started if you have alreadyentered a destination.

Note You should drive on a bit further if the system makes the announce-ment that you are not on a digitalised street before starting route guidance.The unit might have to orientate itself using the next main road.

The active route guidance function will be interrupted if a stopover

destination is entered.

Fig. 46 Ending routeguidance

Start route gd.

NAVI

Stop route gd.

Navigation 39


41/51

Announcement of navigation recommendations

Navigation recommendations are made as spoken

announcements and also in the display.

Press the button page 2, fig. 1 .

Press if you want to hear the current navigation recom-mendation .

You will hear the first announcement after the route has been calculated.

Up to three announcements will be made before a turn has to be made toensure that you are informed in time. A proximity bar will be shown in thedisplay on the right-hand side of the turn arrow shortly before the lastannouncement is made. The proximity bar shows how far away theturning point is. The distance to the next change of direction will be shownin the display after you have turned.

You will receive a recommendation for a lane on roads with more than onelane that then separate off in different directions.

You will also be told which exit to use off a roundabout before you enter it,e.g. that you should leave by the second exit. This announcement will then

be repeated when you are travelling round the roundabout.An announcement will be made when you reach your destination. You willbe informed that you have reached your destination if it is on a digitalisedroad. If it is not on a digitalised road, you will be informed that you havereached the destination area. The latter may occur if you have entered thedestination using coordinates and it is not on a road.

WARNING

You, as the driver, must concentrate on the spoken announce-

ments and also on the traffic around you. The recommendationsmade on the basis of the information on the CD may differ fromwhat you actually see due to incomplete data or a different roadlayout (e.g. due to road works). Please keep to traffic regulationsand ignore the navigation recommendations if necessary.

Traffic signs and legislation always have priority over therecommendations made by the system.

Fig. 47 Map display

Fig. 48 Symbol display

MAP A12

Navigation40


42/51

Please observe the important safety warnings page 14,Safety.

NoteThe direction arrow in the map display will be faded out if you are travellingin the same direction for an extended period.

WARNING (continued)

Information and system settings 41


43/51

Information and system settings

Information

The radio navigations system stores text and spoken

announcements made by the radio stations and draws upa route list whilst the route guidance function is active.

Press button page 2, fig. 1 to enter the Info mainmenu.

Function keys in the Info main menu

The function keys TIM messages, Travel inform., Route list and TMCstations are green if no further information is available.

Plays back recorded traffic reports (Stop by pressing page 2, fig. 1 ).

The TIM messages are stored chronologically. The latest message is atthe top of the list. The selection bar will spring automatically to the nextmessage once the first message has been played. The system will returnto the main menu after the last message has been played and will thenreactivate the audio source that was being used. The oldest announce-ment will be overwritten if the memory is full.

Fig. 49 Info main menu

Fig. 50 Setting the TIMtime

INFO A18

TIM messages

ESC A11

Information and system settings42


44/51

Displays a list of receivable TMC stations. Select a stationwhose traffic reports should be played if you happen to be listening toanother radio station. A different station will be chosen automatically if theselected station can no longer be received.

Displays a list of the latest traffic reports page 35.

page 42

Displays the software version installed in the radio naviga-tion system.

Displays a list of the streets on the route to the destination.Use the menu knob to page through the street lists that are on your navi-gation route. Press if an entry is not fully displayed.

page 37

TIM time 1 and TIM time 2: Two different departure times can be

entered here, e.g. 7.00 a.m. and 5.30 p.m. The unit will start recordingtraffic reports 1.5 hours before your departure. This means that you willhave up to date traffic information right from the start of your journey.

TIM standby Traffic reports will be recorded for two hours after youhave switched off the unit.

NoteThe list of announcements cannot be opened whilst a traffic announce-ment is being made, as it is also being recorded.

System settings

In the system settings menu, you can select different

languages for the displays and spoken announcements,

and adjust the screen brightness.

In the Info main menu, press page 41, fig. 49to see which settings can be made. You can also call up thesystem settings from the Radio main menu by pressing

page 6, fig. 4 or from the CD main menu page 10, fig. 9.

Function keys in the Settings menu Shows a list of available languages for display texts and

spoken announcements. Select a language by turning and pressing themenu knob. You will see a display text in the chosen language. Do notpress any further keys until the loading sequence is finished.

TMC stations

Travel inform.

Syst. settings

System Info

Route list

Position display

Set-up

Fig. 51 Systemsettings

Syst. settings

Set-up

Language

Information and system settings 43


45/51

You can set the screen brightness to be adjusted to suit thelight conditions when the headlights are switched on.

auto: The night display will automatically be selected when the head-lights are switched on.

manual: Press page 2, fig. 1 to switch between the day andnight displays.

and Sets the screen settings for the day andnight display.

The clock can be set here by turning and pushing the menu knobif the time has not be taken over from the clock in the combi-instrument.The data for the arrival time is oriented towards this time if the route guid-ance function is active.

NoteThe language can only be changed if the navigation CD has been

inserted.

Day / Night

A13

Contrast day Contrast night

Time

External units44


46/51

External units

Calling up external units

Calling up external units

Press the key page 2, fig. 1 to enter the AUXmain menu.

Function keys in the AUX main menu

Switches over to an external audio (A) or video (V) source.

Switches to an audio unit which is connected to the system.

Settings for the units connected to the system:

A+V: The unit AV1 or AV2 delivers audio and video signals (sound andpicture).

AUDIO: The unit delivers audio signals only.

VIDEO: The unit delivers video signals only.

OFF: There is no unit connected.

Fig. 52 Main menuAUX

AUX A14

AV (A/V)

AUX (A)

Set-up

Index 45


47/51

Index

AAllocating the radio stations

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

AM

Medium wave . . . . . . . . . . . . . . . . . . . . . . . 7

Announcements . . . . . . . . . . . . . . . . . . . . . . 39

AS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Autozoom . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

AUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

AV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

BBack/Forwards

Radio station selection . . . . . . . . . . . . . . . . 8

Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Blocking stretches of the journey . . . . . . . . . 30

CCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Ejection . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Fast forward/reverse . . . . . . . . . . . . . . . . 10Playing a CD from the CD changer . . . . . 11

Comfort Coding . . . . . . . . . . . . . . . . . . . . . . . . 5

Control elements . . . . . . . . . . . . . . . . . . . . . . . 2

Coordinates . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Crosshair . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

DDay/night display . . . . . . . . . . . . . . . . . . . . . . 42

Default settings . . . . . . . . . . . . . . . . . . . . . . . 13

Delete

Destinations in the destination memory . . 26

Last destinations . . . . . . . . . . . . . . . . . . . 20

Letters, symbols, numbers . . . . . . . . . . . . 19

Demonstration . . . . . . . . . . . . . . . . . . . . . . . . 28

Destination . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Renaming . . . . . . . . . . . . . . . . . . . . . . . . . 24

Sorting . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Destination entry . . . . . . . . . . . . . . . . . . . . . . 17Destination memory . . . . . . . . . . . . . . . . . 20

Destination on the map . . . . . . . . . . . . . . 21

Intersection, centre . . . . . . . . . . . . . . . . . . 19

Last destinations . . . . . . . . . . . . . . . . . . . 19

Position destination . . . . . . . . . . . . . . . . . 22

Special destinations . . . . . . . . . . . . . . . . . 21

Town, street, house number . . . . . . . . . . 18

Destination memory . . . . . . . . . . . . . . . . . . . . 23

EESC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

FFactory settings . . . . . . . . . . . . . . . . . . . . . . . 13

FM

VHF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Function keys . . . . . . . . . . . . . . . . . . . . . . . . . . 3

GGALA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

IINFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Initial Autostore . . . . . . . . . . . . . . . . . . . . . . . . 7

KKeys

Quick reference guide . . . . . . . . . . . . . . . . 3

LLanguage setting . . . . . . . . . . . . . . . . . . . . . . 42

Last destinations . . . . . . . . . . . . . . . . . . . . . . 19

Latitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

List of stations . . . . . . . . . . . . . . . . . . . . . . . . . 8

Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Index46


48/51

Longitude . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

MMain menu

AUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

AV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Navigation . . . . . . . . . . . . . . . . . . . . . . . . 16

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Map

Alignment . . . . . . . . . . . . . . . . . . . . . . . . 34

Map contents . . . . . . . . . . . . . . . . . . . . . . . . 36

Map display . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Display options . . . . . . . . . . . . . . . . . . . . 34Map section . . . . . . . . . . . . . . . . . . . . . . . . . 35

Map type . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Menu knob . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Mix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Muting

Navigation recommendations . . . . . . . . . 12

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

NNavigation . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Navigation CD . . . . . . . . . . . . . . . . . . . . . . . . 15

Navigation recommendations . . . . . . . . . . . . 39

PParameters for route calculation . . . . . . . . . . 27

Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Position display . . . . . . . . . . . . . . . . . . . . . . . 37

QQuick reference guide . . . . . . . . . . . . . . . . . . . 2

RRadio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Radio station selection . . . . . . . . . . . . . . . . 8, 9

From list . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Route guidance . . . . . . . . . . . . . . . . . . . . 29, 38

Route list . . . . . . . . . . . . . . . . . . . . . . . . . 36, 42

Route options . . . . . . . . . . . . . . . . . . . . . . . . 27

SSafety code . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Radio stations . . . . . . . . . . . . . . . . . . . . . . 6

Screen

Darkened . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Setting the clock . . . . . . . . . . . . . . . . . . . . . . 42

Settings

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Settings at time of delivery . . . . . . . . . . . . . . 13

Software version . . . . . . . . . . . . . . . . . . . . . . 42

Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Special characters . . . . . . . . . . . . . . . . . . . . . 19

Spoken announcements . . . . . . . . . . . . . . . . 41

Station keys . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Status bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Stopover destination . . . . . . . . . . . . . . . . . . . 17

Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Switch-on volume . . . . . . . . . . . . . . . . . . . . . 12

Symbol display . . . . . . . . . . . . . . . . . . . . . . . 33

System info . . . . . . . . . . . . . . . . . . . . . . . . . . 42

System settings . . . . . . . . . . . . . . . . . . . . . . . 42

TText reports . . . . . . . . . . . . . . . . . . . . . . . . . . 41

TIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Time format . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Traffic

Text announcements . . . . . . . . . . . . . . . . 35

Traffic information reports . . . . . . . . . . . . . . . . 7Traffic jam function . . . . . . . . . . . . . . . . . . . . 30

Traffic reports

Spoken announcements . . . . . . . . . . . . . 41

Index 47

U


49/51

UUnit card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

V

Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

WWaveband

Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7


50/51

koda Auto is constantly working on the further development of all types and models. Please understand that, for this reason, chan-ges to the scope of supply in terms of shape, equipment and engineering may be introduced at any time. It is therefore not possibleto derive any claims from the information, illustrations and descriptions contained in this Owner s Manual .

Reprinting, reproduction, translation or any other use of this document, in whole or in parts, is not permitted without the writtenconsent of koda Auto.

koda Auto expressly reserves all rights in respect of copyright.Subject to modification.

Published by KODA AUTO a.s.

KODA AUTO a.s. 2004

;This paper was manufactured from pulp bleached without using chlorine.


51/51

www.skoda-auto.com Radionavigan systm NexusOctavia anglicky 12.05

S00.5610.28.201Z0 012 151 C

A5 Octavia Nexus NavigationSystem

Documents

Transcript of A5 Octavia Nexus NavigationSystem