884 GUIDE VERS032014
Transcript of 884 GUIDE VERS032014
1
884 GUIDE
VERS032014
2
3
KEY HEADS AND THEIR USES …………... 4
KEYLESS START KIT KITS …………... 5
RK60 APPLICATION GUIDE 6
TRANSPONDER ID CROSS REF 7
CAR REG YEAR LIST 7
CLONING PROCEEDURES 8
FIXED CODE TRANPONDER 8
TEXAS FIXED CODE TRANSPONDER 9
TEXAS CRYPTO TRANSPONDER 10
PHILIPS CRYPTO TRANSPONDER 12
PHILIPS CRYTPO 2 TRANSPONDER 14
RK60 CLONING 17
BM100 KIT 22
VL100KIT 24
KIHY100KIT 26
RECOVERY OF LOST ID45 PH1D 28
4
Usually used on cars pre 2000. Many different profiles available for
different car manufacturers. They carbon FIXED CODE transponder.
884 IDs include PH00, MG00. TM00. TM10,TM20
Our key references start TP, please see Davenport Burgess catalogue
Used to clone keys with a PHILIPS CRYPTO transponder
884 IDs include PH1B PH1D PH1E
Used for cloning of certain PHILIPS CRYPTO keys AND remotes.
Please see the supporting information below for cloning RK60 heads
Clones 884 IDs PH20
A universal head that can be used for all cloning EXCEPT when a TK50 is required
Clones 884 ID’s PH00 MG00 TM00 TM10 TM20 PH1A PH1B PH1D PH1E TX00
TX01 TX02
PLEASE NOTE: Currently your 884 will recognise all PH20(46) keys as suitable for use with RK60, so it very important to refer to the application list in this pack, or in the 2013 KL car book, if the model isn’t listed, you cannot use RK60 and will have to clone to TK60/100.
There are certain limitations when cloning RK60 keys.
A vehicles CPU recognises each security device as an individual and so stores each key/fob in a different slot in its memory so it can differentiate between a genuine start of the car and a security breech.
Because of this, when you clone a key (rather than program a new key into a new slot in the memory) the cloning device (884) replicates the information on the original key and copies this onto the copy key. When this copy key is inserted into the cars ignition, the car recognises it as the original key it was copied from; rather than a new individual key.
When we clone onto an RK60, the same thing occurs; the car recognises the new remote as if it was the original. Therefore, if the RK60 is used directly after the original key, it will push the original remotes signal from the cars memory and replace it with it’s own, and vice versa. This can mean that although both keys will start the car at all times, it will cause the previous key used to remotely unlock the car (whether this was the original remote OR the RK60) to lose connection and no longer lock or unlock the car.
THIS DOES NOT RUIN THE KEY, both the RK60 and the original key can be reactivated easily. Please see RK60 cloning instruction on page 6.
5
Keyless start kits allow the reproduction
of certain keys that originally have a keyless fob to start the car. These are
not remote keys. Unlocking of the car is via the manual key included in the
set and the fob inserts into the dashboard like the original fob to start the
car.
MODEL FROM TO
SERIES 1 2007 2010
SERIES 3 2005 2011
SERIES 5 2004 2010
SERIES 6 2004 2010
X1 2009 2011
X5 2007 2011
MODEL FROM TO
V70 2008 2011
XC70 2008 2011
S80 2008 2011
MODEL FROM TO
SORENTO 2010 2012
SPORTAGE 2010 2012
CEED 2011
SOUL 2011
SANRA FE 2011
SONATA 2011
MODEL FROM TO
PRIUS 2004 2009
MODEL FROM TO
370Z 2009 2013
ALTIMA 2DR 2007 2013
ALTIMA 4DR 2007 2012
ALTIMA 4 DR 2012 2013
CUBE 2009 2011
JUKE 2011 2013
LEAF 2011 2013
MAXIMA 2009 2013
MURANO 2009 2012
PATHFIND-
ER 2012 2013
QUEST 2012 2013
SENTRA 2013 2013
MODEL FROM TO
YARIS 2010 2012
6
You must check that the make and model of the car you need to clone against
this list before attempting to clone onto a RK60. If your vehicle is not present,
you cannot clone this key
7
Below is a list of transponder ID’s and their Keyline equivalent. You may find this
useful if you are used to other manufacturers IDs
A…..1983 M…..1994
B…..1984 N…..1995
C…..1985 P…..1996
D…..1986 R…..1997
E…..1987 S…..1998
F…..1988 T…..1999
G…..1989 V…..1999
H…..1990 W…..2000
J…..1991 X…..2000
K…..1992 Y…..2001
L…..1993 Z…..2001
51….2001 08….2008
02….2002 58….2008
52….2002 09….2009
03….2003 59….2009
53….2003 10….2010
04….2004 60….2010
54….2004 11….2011
05….2005 61….2011
55….2005 12….2012
06….2006 62….2012
56….2006 13….2013
07….2007 63….2013
57….2007 14….2014
64….2014
8
Now you can proceed to cutting the transponder key
READING IN PROGRESS ….. PLEASE WAIT…..
On starting your machine you
will see this screen
Insert your original key into the
key reader
Press READ>
And the display on the 884
will show:
Then the 884 will display:
The 884 may also display TEMIC or
MEGAMOS in place of PHILIPS. Also
INSERT THE KEY AND PRESS READ
TRANSPONDER PHILIPS PH00 (33) CAN DUPLICATE
WRITING IN PROGRESS ….. PLEASE WAIT…..
Press
And the display on the 884
will show:
Writing completed, 884
should display: WRITING SUCCESSFUL PRESS READ/WRITE
NOW YOU CAN REMOVE THE ORIGINAL KEY AND REPLACE IT WITH A FIXED
CODE TRANSPONDER. (OUR REF TP501-TP590)
Cloning any key that identifies as a PHILIPS PH00, MEGAMOS MG00,
TEMIC TM00, SOKYMAT (23)
9
READING IN PROGRESS ….. PLEASE WAIT…..
TRANSPONDER TEXAS TX00-4C CAN DUPLICATE
INSERT THE KEY AND PRESS READ
LEAVE THE ORIGINAL KEY IN THE 884 AND PRESS THE
WRITING IN PROGRESS ….. PLEASE WAIT…..
Press
And the display on
the 884 will show:
INSERT TK24/TK100 PRESS WRITE
Press
On starting your
machine you will
see this screen
Insert your origi-
nal key into the
key reader
Press
And the display
Then the 884
will display:
Your 884 will
display:
Replace the origi-
nal with a TK100
Writing completed,
884 should display:
WRITING SUCCESSFUL PRESS READ/WRITE
Remove the key and
fit the TK100/24 to
the relevant
Horseshoe, proceed
to cut the key
*Cloning any key that identifies as a TEXAS TX00-4C onto TK24/TK100
10
READING IN PROGRESS
….. PLEASE WAIT…..
On starting your machine you
will see this screen
Insert your original key into the
key reader
Press READ>
And the display on the 884
will show:
Then the 884 will display:
TEXAS CRYPTO TPXX 01
CAN DUPLICATE
INSERT THE KEY
AND PRESS READ
LEAVE THE ORIGINAL KEY IN THE 884 AND PRESS THE WRITE BUT-
TON
Your machine will now calculate
the information:
CALCULATING
PLEASE WAIT 03
Your 884 will display:
PRESS WRITE FOR YES
PROG. CRYPTO KEY?
RD = NO WR =
Cloning any key that identifies as a TEXAS TX 4D onto TK100/40
11
Press Replace the original with a
TK100 (or TK40) head.
WRITING IN PROGRESS
….. PLEASE WAIT….. Press WRITE> And the display on the 884
will show:
Your machine will now INSERT TK40/100
PRESS WRITE
Writing completed, 884
should display:
WRITING SUCCESSFUL
PRESS READ/WRITE
Remove the key and fit the
TK100/40 to the relevant
Horseshoe and proceed to cut
the key
12
READING IN PROGRESS
….. PLEASE WAIT…..
On starting your machine you
will see this screen
Insert your original key into the
key reader
Press READ>
And the display on the 884
will show:
Then the 884 will display:
* It also can display PH1D or
PH1E
TRANSPONDER PH1B
CAN DUPLICATE
INSERT THE KEY
AND PRESS READ
LEAVE THE ORIGINAL KEY IN THE 884 AND PRESS THE WRITE BUTTON
The machine will now display
DO NOT REMOBE THE KEY
PLEASE WAIT
Your 884 will display:
INSERT ORIGINAL KEY
PRESS WRITE
Cloning any key that identifies as a PHILIPS CRYPTO PH1b/PH1D/PH1e
onto a TK50 head
Press WRITE>
13
Press Replace the original with a
TK50 head
WRITING IN PROGRESS
….. PLEASE WAIT….. Press WRITE> And the display on the 884
will show:
Your machine will now
display:
INSERT TK50
PRESS WRITE
Writing completed, 884
should display:
WRITING SUCCESSFUL
PRESS READ/WRITE
Remove the key and fit the
TK50 to the relevant horse-
shoe and proceed to cut the
key
14
Cloning any key that identifies as a PHILIPS CRYPTO 2 PH20 (46) ONTO A
TK100/60
READING IN PROGRESS
….. PLEASE WAIT…..
On starting your machine you will see
this screen
Insert your original key into the key
reader
Press READ>
And the display on the 884 will show:
Then the 884 will display:
CRYPTO PHILIPS PH20 46
CAN DUPLICATE
INSERT THE KEY
AND PRESS READ
LEAVE THE ORIGINAL KEY IN THE 884 AND PRESS THE WRITE BUTTON
Your 884 will display: TK60/100 STEP 1 COMPLETE
PROCEED TO STEP 2
Press Replace the original with a TK100/60
Your machine will now display:
PLEASE NOTE IF YOU WANT TO USE AN
RK60,PLEASE REFER TO THE RK60 APP LIST; IF
THE CAR MAKE AND MODEL DOES NOT EXSIST
ON THE LIST YOU NEED TO USE TK100/60 ON-
LY
INSERT RK60/TK100/TK60
PRESS WRITE
Press WRITE>
15
STEP 2 YOU WILL NEED TO HAVE ACCESS TO THE VEHICLE FOR THIS STEP
Remove the key and fit the
TK100/60 to the relevant
Horseshoe, proceed to cut the
key
Your 884 will now display: STEP 2 COMPLETE
PRESS WRITE
RETURN TO THE 884, INSERT THE TK100/60 INTO THE READER
AND PRESS READ
Your 884 will display:
PRESS WRITE FOR YES
PROG. CRYPTO KEY?
ALL BRANDS OF CAR.
Go to the car and insert the TK100/60 into the ignition, hold on for 10 seconds,
(enough time for the dash lights to light up and go out) , remove the key and wait
for the dash lights to go out, repeat this 3 times
10 10
10 10 10 10 10
RENAULT ONLY.
Go to the car and insert the TK100/60 into the ignition, hold on for 10 seconds,
(enough time for the dash lights to light up and go out) ,remove the key and wait
for the dash lights to go out, repeat this with the original key. Then repeat this se-
quence until you have done this 6 times, ending with the original key
16
Press
WRITE>
Press Replace the TK60/100 with
THE ORIGINAL KEY.
Your 884 will display:
INSERT ORIGINAL KEY
PRESS WRITE
Your machine will now calculate
the information:
The machine should count up to 100
CALCULATING
PLEASE WAIT 03
Your machine will now
display:
INSERT TK60/100
PRESS WRITE
Press
Replace the original with a
TK60/100 head
PRESS WRITE
Writing completed, 884
should display: If you get any other message,
please refer to the help section
WRITING SUCCESSFUL
PRESS READ/WRITE
17
Cloning any key that identifies as a PHILIPS CRYPTO 2 PH20 (46) ONTO A
RK60 REMOTE. FOR FIAT PLEASE SEE PAGE ***
READING IN PROGRESS
….. PLEASE WAIT…..
On starting your machine you will see
this screen
Insert your original key into the key
reader
Press READ>
And the display on the 884 will show:
Then the 884 will display:
CRYPTO PHILIPS PH20 46
CAN DUPLICATE
INSERT THE KEY
AND PRESS READ
Your 884 will display: TK60/100 STEP 1 COMPLETE
PROCEED TO STEP 2
Press Replace the original with a RK60 head.
Your machine will now display:
PLEASE NOTE IF YOU WANT TO USE AN
RK60,PLEASE REFER TO THE RK60 APP LIST; IF
THE CAR MAKE AND MODEL DOES NOT EXSIST
ON THE LIST YOU NEED TO USE TK100/60 ON-
LY
INSERT RK60/TK100/TK60
PRESS WRITE
Press WRITE>
18
STEP 2 YOU WILL NEED TO HAVE ACCESS TO THE VEHICLE FOR THIS STEP
Remove the key and fit the RK60
to the relevant
Horseshoe, proceed to cut the
key
Your 884 will now display: STEP 2 COMPLETE
PRESS WRITE
RETURN TO THE 884, INSERT THE RK60 INTO THE READER AND
PRESS READ
Your 884 will display:
PRESS WRITE FOR YES
PROG. CRYPTO KEY?
RD = NO WR = YES
ALL BRANDS OF CAR.
Go to the car and insert the RK60 the ignition, hold on for 10 seconds, (enough time for the dash
lights to light up and go out) , remove the key and wait for the dash lights to go out, repeat this 3
times
10 10
10 10 10 10 10
RENAULT ONLY.
Go to the car and insert the RK60 into the ignition, hold on for 10 seconds, (enough time for the
dash lights to light up and go out) ,remove the key and wait for the dash lights to go out, repeat
this with the original key. Then repeat this sequence until you have done this 6 times, ending with
the original key.
19
Press
WRITE>
Press Replace the RK60with THE
ORIGINAL KEY.
Your 884 will display:
INSERT ORIGINAL KEY
PRESS WRITE
Your machine will now calculate
the information:
The machine should count up to 100
CALCULATING
PLEASE WAIT 03
Hold the lock button until this
message appears
PUSH TRUNK BUTTON
Hold the open button until this
message appears
PUSH LOCK BUTTON
Next your machine will now
display:
PUSH OPEN BUTTON
Hold the BOOT button until this
message appears
If you do not have a boot button,
PUSH TRUNK BUTTON
IF YOU ARE CLONING RK60 FOR FIAT… PLEASE GO TO PAGE ***
Fiat users got to
page 21 now
20
GO TO THE VEHICLE AND PRESS THE OPEN BUTTON ON THE
RK60 TWICE
OPEN THE CAR MANUALLY OR WITH THE ORIGINAL REMOTE
TURN ON THE CAR WITH THE RK60
TEST THE RK60 REMOTE
Your machine will now REINSERT RK60
PRESS WRITE
Press
Replace the original with a
RK60 head.
PRESS WRITE
Writing completed, 884 WRITING SUCCESSFUL
PRESS READ/WRITE Your 884 will display:
21
Hold the open button until this
message appears
ACTIVATE REMOTE 03
Hold the open button until this
message appears
ACTIVATE REMOTE 02
Next your machine will now
display:
ACTIVATE REMOTE 01
Hold the open button until this
message appears
REINSERT TK60/100
PRESS WRITE
After following the previous step by step instructions, see below to com-
plete FIAT procedure
GO TO THE VEHICLE AND PRESS THE OPEN BUTTON ON THE
RK60 TWICE
OPEN THE CAR MANUALLY OR WITH THE ORIGINAL REMOTE
TURN ON THE CAR WITH THE RK60
TEST THE RK60 REMOTE
Press
Replace the original with a RK60
head.
PRESS WRITE
WRITING SUCCESSFUL
PRESS READ/WRITE
Writing completed, 884 should
display:
If you get any other message, please
refer to the help section
22
READING IN PROGRESS
….. PLEASE WAIT…..
On starting your machine you will see
this screen
Insert your original key into the key
reader
Press READ>
And the display on the 884 will show:
Then the 884 will display:
CRYPTO PHILIPS PH20 46
CAN DUPLICATE
INSERT THE KEY
AND PRESS READ
LEAVE THE ORIGINAL KEY IN THE 884 AND PRESS THE WRITE BUTTON
Your 884 will display: TK60/100 STEP 1 COMPLETE
PROCEED TO STEP 2
Press Replace the original with a BM100
Your machine will now display:
THIS IS CORRECT EVEN THOUGH YOU WILL BE
USING A BM100KIT
INSERT RK60/TK100/TK60
PRESS WRITE
Press WRITE>
Cloning any key that identifies as a PHILIPS CRYPTO 2 PH20 (46) ONTO
THE BL100KIT, PLEASE REFER TO APPLICATION LIST TO ENSURE YOU CAN
CLONE THIS KEY
23
Take the key blade included in the BM100KIT and cut to the original key.
STEP 2 YOU WILL NEED TO HAVE ACCESS TO THE VEHICLE FOR THIS STEP
Go to the car and insert the BM100 fob into the ignition and press the start/stop
button without starting the car for around 10 seconds, press the start/stop button
to turn the cars ignition off, repeat this 3 times
10 10
Your 884 will now display:
STEP 2 COMPLETE
PRESS WRITE
RETURN TO THE 884, INSERT THE BM100 INTO THE READER AND
PRESS READ
Your 884 will display:
PRESS WRITE FOR YES
PROG. CRYPTO KEY?
RD = NO WR = YES
Press
WRITE>
Press Replace the BM100 with THE
ORIGINAL KEY.
Your 884 will display:
INSERT ORIGINAL KEY
PRESS WRITE
Your machine will now calculate
the information:
The machine should count up to 100
CALCULATING
PLEASE WAIT 03
Writing completed, 884
should display: If you get any other message, please
refer to the help section
WRITING SUCCESSFUL
PRESS READ/WRITE
24
READING IN PROGRESS
….. PLEASE WAIT…..
On starting your machine you will see
this screen
Insert your original key into the key
reader
Press READ>
And the display on the 884 will show:
Then the 884 will display:
CRYPTO PHILIPS PH20 46
CAN DUPLICATE
INSERT THE KEY
AND PRESS READ
LEAVE THE ORIGINAL KEY IN THE 884 AND PRESS THE WRITE BUTTON
Your 884 will display: TK60/100 STEP 1 COMPLETE
PROCEED TO STEP 2
Press Replace the original with a VL100
Your machine will now display:
THIS IS CORRECT EVEN THOUGH YOU WILL BE
USING A BM100KIT
INSERT RK60/TK100/TK60
PRESS WRITE
Press WRITE>
Cloning any key that identifies as a PHILIPS CRYPTO 2 PH20 (46) ONTO
THE BL100KIT, PLEASE REFER TO APPLICATION LIST TO ENSURE YOU CAN
CLONE THIS KEY
25
Take the key blade included in the BM100KIT and cut to the original key.
STEP 2 YOU WILL NEED TO HAVE ACCESS TO THE VEHICLE FOR THIS STEP
Go to the car and insert the VL100 fob into the ignition and press the start/stop
button without starting the car for around 10 seconds, press the start/stop button
to turn the cars ignition off, repeat this 3 times
10 10
Your 884 will now display:
STEP 2 COMPLETE
PRESS WRITE
RETURN TO THE 884, INSERT THE VL100 INTO THE READER AND
PRESS READ
Your 884 will display:
PRESS WRITE FOR YES
PROG. CRYPTO KEY?
RD = NO WR = YES
Press
WRITE>
Press Replace the VL100 with THE
ORIGINAL KEY.
Your 884 will display:
INSERT ORIGINAL KEY
PRESS WRITE
Your machine will now calculate
the information:
The machine should count up to 100
CALCULATING
PLEASE WAIT 03
Writing completed, 884
should display: If you get any other message, please
refer to the help section
WRITING SUCCESSFUL
PRESS READ/WRITE
26
READING IN PROGRESS
….. PLEASE WAIT…..
On starting your machine you will see
this screen
Insert your original key into the key
reader
Press READ>
And the display on the 884 will show:
Then the 884 will display:
CRYPTO PHILIPS PH20 46
CAN DUPLICATE
INSERT THE KEY
AND PRESS READ
LEAVE THE ORIGINAL KEY IN THE 884 AND PRESS THE WRITE BUTTON
Your 884 will display: TK60/100 STEP 1 COMPLETE
PROCEED TO STEP 2
Press Replace the original with a KIHY100KIT
Your machine will now display:
THIS IS CORRECT EVEN THOUGH YOU WILL BE
USING A BM100KIT
INSERT RK60/TK100/TK60
PRESS WRITE
Press WRITE>
Cloning any key that
identifies as a PHILIPS CRYPTO 2 PH20 (46) ONTO THE BL100KIT, PLEASE
REFER TO APPLICATION LIST TO ENSURE YOU CAN CLONE THIS KEY
27
Take the key blade included in the
STEP 2 YOU WILL NEED TO HAVE ACCESS TO THE VEHICLE FOR THIS STEP
Go to the car and insert the KIHY100 fob into the ignition and press the start/stop
button without starting the car for around 10 seconds, press the start/stop button
to turn the cars ignition off, repeat this 3 times
10 10
Your 884 will now display:
STEP 2 COMPLETE
PRESS WRITE
RETURN TO THE 884, INSERT THE KIHY100 INTO THE READER AND
PRESS READ
Your 884 will display:
PRESS WRITE FOR YES
PROG. CRYPTO KEY?
RD = NO WR = YES
Press
WRITE>
Press Replace the KIHY100 with THE
ORIGINAL KEY.
Your 884 will display:
INSERT ORIGINAL KEY
PRESS WRITE
Your machine will now calculate
the information:
The machine should count up to 100
CALCULATING
PLEASE WAIT 03
Writing completed, 884
should display: If you get any other message, please
refer to the help section
WRITING SUCCESSFUL
PRESS READ/WRITE
28
If the original key is removed or there is a power failure during the analysis
of the original key (the phase in which the machine displays the message,
“do not remove the key”. If this happens the data on the key can be lost
and the key will not start the car. With the 884 it is possible to retrieve this
data. But the key in question has to have been the last key to have been
used on the machine
READING IN PROGRESS
On starting your machine you
will see this screen
Insert your original key into
the key reader
Press And the display on the 884
will show:
Then the 884 will display:
INSERT THE KEY
WITH THE ORIGINAL KEY STILL IN THE MACHINE, HOLD DOWN
THE F1 KEY ON THE KEYBOARD OF THE 884 FOR 3 SECONDS
CRYPTO PHIL . PH1D (45)
CLONABLE RPESS WIRTE
KEY GENERATED
On your machine you will see DO NOT REMOVE THE KEY
DO NOT REMOVE THE KEY AT THIS POINT
WAIT FOR THE FOLLOWING MESSAGE
THE KEY IS NOW REGENERATED AND READY TO USE
29
The RK60/TK60/100 can be reused up to 10 times, but needs to be
cancelled after being used for a PH20 ID46 Philips crypto 2 key in order
for it to be used again.
Please see below for how to do this.
READING IN PROGRESS
….. PLEASE WAIT…..
On starting your machine
you will see this screen
Insert your TK60/100 into
the key reader
Press
And the display on the
Then the 884 will display:
INSERT THE KEY
AND PRESS READ
PRESS WRITE WITH THE TK100/60 IN THE 884
TK 60 / TK100 STEP 2
On your machine you will
PROG CRYPTO KEY?
RD = NO
DELETE KEY?
RE = NO WR = YES Press
And the display on the
PRESS WRITE AND NOW THE KEY IS CANCELED
PROG CRYPTO KEY?
30