68DCCAT

8/9/2019 68DCCAT

1/44

Features

• High reliability

• Simple installation and operation

• LCD display for self-guided controller operation

• RS232 interface for remote operation

• Intelligent battery management:

• Temperature compensation

(requires optional cables)

• Programmable battery load testing with

data logging

• Symmetry (requires optional cables)

• Programmable low voltage disconnect

• Optional Ethernet (SNMP compatible) interface

module

• Natural convection cooling - no fans

• International standards compliance

Description

PPS 7 modular DC power shelf systems

provide large power system features in

cost-effective, rack-mounted form factors.

These shelf power solutions provide

rectification, system management, and

power distribution while maintaining high

reliability and offering flexibility for future

expansion. The PPS 7 systems are based

on hot-swappable rectifier modules output

power available at 450, 560 or 670W per

module.

System management is accomplished

through messages and alarms displayed

on the system controller’s (PCU) LCD

screen and can also be displayed

remotely via the PC-based PowComTM

software package.

PPS 7 Power SystemShelf System

www.power-one.com

8/9/2019 68DCCAT

2/44

An all-in-one 3U high shelf system that can be

installed in both 19” and ETSI telecom cabinet

solutions. The system subrack can

accommodate up to three rectifier modules, a

supervision module (PCU) and DC distribution

with a single battery breaker and six load

breakers.

PPS 7-2100 System


installed in both 19” and ETSI telecom cabinet


accommodate up to four rectifier modules, a

supervision module (PCU) and DC

distribution with a single battery breaker and a

single load breaker.

PPS 7-2800 System


installed in 23” standard telecom cabinet


accommodate up to six rectifier modules, a


with up to two battery breakers and twenty

four load breakers.

PPS 7-4200 System An all-in-one 6U high shelf system that can be

installed in 19” and ETSI telecom cabinet


accommodate up to five rectifier modules, a


with up to two battery breakers and twenty

load breakers.

PPS 7-3500 System

System Configurations

8/9/2019 68DCCAT

3/44

Rectifier Features

Model VoltagePower (max.)

Current(max.)

PMP 5.24 SIC 110* 24V DC 448W 16A

PMP 5.48 SIC 110* 48V DC 448W 8A

PMP 7.24 SIC 24V DC 560W 20A

PMP 7.48 SIC 48V DC 672W 12A

PMP 7.60 SIC 60V DC 635W 9A

The PPS 7 system utilizes plug-in rectifier modules that are

based on a soft-switching approach. Features include 3 LEDs

for rectifier status indication, thermal shutdown, and input

overvoltage disconnection with an automatic reset (only on

PMP 7 modules).

• Menu guided operation


• Battery management and testing

• Low voltage battery disconnect (LVBD)• Temperature compensation

• Battery symmetry measurement

• Optional Ethernet interface through SNMP and/or TCP/IP

• Partial load disconnection (PLD)

PCU Features

Rectifier Modules

Advanced system supervision is accomplished using a

microprocessor based control module that allows both local

and remote system monitoring.

Supervision Modules

*110V AC input

System Components

PPS 7 Power SystemShelf System

8/9/2019 68DCCAT

4/44

Note: All specifications are subject to change without notification.

Input

Output

Mechanical

Options

Features

Battery

Model PPS 7-2100 PPS 7-2800 PPS 7-3500 PPS 7-4200

Input

230/400V 3-phase

208-240V 1-phase

Site configurable

230/400V 3-phase

208-240V 1-phase

Site configurable

230/400V 3-phase

208-240V 1-phase

Site configurable

230/400V 3-phase

208-240V 1-phase

Site configurable

Inputs (max.) Single input Single input Single input Single input

Rectifier Modules (max.) 3 4 5 6

Battery Outputs 1 1 2 2

Load Outputs 6 1 20 24

24V DC Version Yes N/A N/A N/A

48V DC Version Yes Yes Yes Yes

60V DC Version Yes (on request ) Yes (on request) Yes (on request) Yes (on request)

Supervision PCU PCU PCU PCU

Battery Symmetry Inputs(max.)

1 1 3 3

Low Voltage Battery

Disconnection (LVBD)Yes Yes Yes Yes

Dimensions (WxHxD) 485x133x305mm 485x133x305mm 485x133x305mm 582x266x305mm

Mounting

19”, ETSI, or flush

ETSI mount

(site configurable)


ETSI mount

(site configurable)


ETSI mount

(site configurable)

23”

Cable Entry Top Top Top Top

Temp. Comp. Charge Yes Yes Yes Yes

Ethernet Network

InterfaceYes Yes Yes Yes

Modem Interface Yes Yes Yes Yes

www.power-one.com

Shelf System

11V0005-036 PPS7 SY V3.0

PPS 7 Power System

8/9/2019 68DCCAT

5/44

Description

The Power-One PMP 5 rectifier moduleprovides a cost-effective power solutionin a high density footprint. Built on thelatest advances in the resonance switchmode approach (soft-switching), the

PMP 5 is the next evolution in our smallconvection cooled rectifier series.

Optimized for telecom applications, themodule is designed to work in amultitude of different subrack/shelf configurations incorporating the Power-One PCU controller and variousdistribution options.

Features• 115/230 VAC input

• 24V, or 48VDC output

• Power factor correction

• Active load sharing

• Hot-swappable


• Natural convection cooling

• Low weight

PPS 5/7 SystemShown

PMP 5Rectifier Module

www.power-one.com

8/9/2019 68DCCAT

6/44

Input

Model PMP 5.24 PMP 5.48

PMP

5.24-110

PMP

5.48-110

Input

Voltage

161-276V AC single

phase, (44-66Hz)

80-138V AC single

phase, (44-66Hz)

Current

(max.)87% >87%

Tolerance Vout +/- 1%

Transient

Response

+/- 5% at load variation 10-90% or 90-10%,

recovery time 10ms

Load Sharing

8/9/2019 68DCCAT

7/44

Description

The Power-One PMP 7 rectifier moduleprovides a cost-effective power solutionin the highest possible density. Built onthe latest advances in the resonanceswitch mode approach (soft-switching),the PMP 7 is the next evolution in our small convection cooled rectifier series.

Optimized for telecom applications, themodule is designed to work in a multitudeof different subrack/shelf configurationsincorporating the Power-One PCUcontroller and various distributionoptions.


• 24V, 48V, or 60V DC output

• Input overvoltage disconnection

• Thermal protection


• Hot-swappable

• Up to 92% efficient



• Low weightPPS 7 3500 SystemShown


www.power-one.com

8/9/2019 68DCCAT

8/44

Input

Model PMP 7.24 PMP 7.48 PMP 7.60

Input

Voltage

205-250V AC ±10% single phase,(44-66Hz) (-15% for PMP7.60)

185-160V at reduced output power

Current

(max.)

8/9/2019 68DCCAT

9/44

The PCU 5/ 7Controllers are usedin PPS5 and PPS7

Power Systems.

DescriptionThe Power-One Control Unit (PCU 5/7) provides monitoring and control for the PPS 5 and PPS 7

power systems. These hot-swappable controller modules supervise output voltages, currents, rectifier

performance, battery condition, and breaker status. Visual notification of an alarm condition is

provided with an LED. A description of the exact alarm condition is provided through an LCD.

Additionally, four Form “C” contacts are provided to indicate a failure.

Features

User controls and interfaces:

• Simple menu-guided operation using front panelmounted pushbuttons and an LCD

• User-selectable alarm parameters

• Data logging of last 40 events

• SNMP interface adapter available

• RS232 interface and Form “C” dry alarm contacts

• Compatible with PowComTM PC-based software

PCU 5/7Controller

www.power-one.com

Intelligent battery management:

• Temperature compensation with programmablecompensation factor

• Automatic and manual load testing

• Battery voltage and symmetry monitoring

• Capacity testing

• Low voltage disconnect

8/9/2019 68DCCAT

10/44

Input

Voltage 18-72V DC

Current

8/9/2019 68DCCAT

11/44

Description

The Power-One PPR 5/7 3 and 6position rectifier backplane provides acost-effective power solution in a highdensity wall-mounted footprint. Thesepower solutions provide rectification,

system management, and power distribution while maintaining highreliability and offering flexibility for future expansion. The PPS 5/7 3 & 6Position systems are based on hot-swappable rectifier modules outputpower available at 450, 560 or 670W per module.


• 24V, or 48VDC output

• Serial or parallel alarm configurations


• Hot-swappable



• Systems can be paralleled

• Individual rectifier output adjustment6 Position SystemShown

PPR 5/73 & 6 Position Power Systems

www.power-one.com

8/9/2019 68DCCAT

12/44

www.power-one.com11V0005-065 PPR 5/7 V3.0

PPR 5/73 & 6 Position Power Systems


Input

Output

Mechanical

Features

Model PPR 5/7 3-Position PPR 5/7 6-Position

Input115 or 230VAC single phase

(Depending on rectifier

module)"

115 or 230VAC single phase

(Depending on rectifier

module)"

Input Connections 3x4mm² terminal blocks 3x4mm² terminal blocks

Rectifier Modules (max.) 3 6

Load Outputs 2x10mm² - Qty 3 2x10mm² - Qty 6

24V DC Version Yes Yes


Alarms

Common alarm for High Voltage/ Shutdown, Low Voltage/

Module Failure, Unequal Load Sharing Normally Opened

or Normally Closed.

Dimensions (WxHxD) 271x193.5x305mm 484.4x193.5x305mm

Weight 1.2kg (2.65lbs.) 2.5kg (5.5lbs.)

Mounting Wall Mount Wall Mount

Model Voltage Power (max.) Current (max.)

PMP 5.24 24V DC 448W 16A

PMP 5.24 SIC 110* 24V DC 448W 16A

PMP 5.48 SIC 110* 48V DC 448W 8A

PMP 7.24 SIC 24V DC 560W 20A

PMP 7.48 SIC 48V DC 672W 12A

*110V AC input

Available Rectifiers

8/9/2019 68DCCAT

13/44

Features


• Simple installation and operation

• Natural convection cooling - no fans


• Form “C” dry alarm contacts

• Intelligent battery management

• Pluggable controller and DC distribution

modules

• Optional Ethernet (SNMP compatible) interface

module• International standards compliance

Description

The Galero™ Power System provides

large power system features in cost-

effective, rack-mounted form factors.

These power solutions provide

rectification, control and power

distribution all in one compact system

while offering extensive local and remote

power system and battery monitoring.

System management is accomplished

through the system controller (GMC).Status indication is made via LED’s, while

detailed information and remote operation

are accomplished through the PC-based

PowComTM software package.

Galero™ Power System

www.power-one.com

Shelf System

8/9/2019 68DCCAT

14/44

All-in-one 125 mm high shelf system for integration into standard

19” or ETSI cabinets.

Complete subrack for five rectifier modules, supervision module

and DC distribution with battery breakers (1-2) and load breakers

(9-10).

Galero 1750 System

All-in-one 125 mm high shelf system for integration into

standard 19” or ETSI cabinets.Complete subrack for seven rectifier modules, supervision

module and DC distribution including battery breakers (1-2) and

load breakers (2-3).

Galero 2450 System


8/9/2019 68DCCAT

15/44

Rectifier Features

Model VoltagePower (max.)

Current(max.)

CMP 3.48 48V DC 364W 6.5A

The Galero Shelf System utilizes plug-in rectifier

modules based on a soft-switching approach.

Features include 2xLED for rectifier status indication,

thermal protection with de-rating and input over-

voltage disconnection with automatic reset.

• Advanced system monitoring


• Battery management and testing

• Automatic testing

• Low voltage battery disconnect (LVBD)

• Temperature compensation

• Battery symmetry measurement

• Monthly logging of battery parameters including “temperature-hours”

• Site programmable Flash EPROM

• Programmable alarms

• Programmable logic circuit

• Optional Ethernet interface through SNMP and/or TCP/IP

GMC Features

Rectifier Module

Advanced system supervision is accomplished using a

microprocessor based module that allows both local and

remote system monitoring.

Supervision Module - GMC

System Components

Galero™ Power SystemShelf System

8/9/2019 68DCCAT

16/44


Input

Output

Mechanical

Options

Features

Battery

Model Galero 1750 Galero 2450

Input

230/400V AC 3-phase

205-240V AC 1-phase

Site configurable

230/400V AC 3-phase

205-240V AC 1-phase

Site configurable

Inputs (max.) Single input Single input

Rectifier Modules (max.) 5 7

Battery Outputs 1 2 1 2

Load Outputs 10 9 3 2


Supervision GMC GMC

Battery Symmetry Inputs (max.) 2 2

Low Voltage Battery

Disconnection (LVBD)Yes Yes

Temp. Comp. Charge Yes Yes

Dimensions (WxHxD) 483x125x280mm 483x125x280mm

Mounting 19”, ETSI 19”, ETSI

Cable Entry AC - Rear

DC and signals -Top

AC - Rear

DC and signals -Top

Temp. Comp. Charge Yes Yes

Battery SymmetryMeasurement

Yes Yes

Ethernet Network Interface Yes Yes

Partial Load Disconnect N/A N/A

Integrated Surge Arrestors N/A N/A

www.power-one.com11V0005-033 Galero SY V3.0

Galero™ Power SystemShelf System

8/9/2019 68DCCAT

17/44

Description

The Power-One CMP 3.48, for use in theGalero™ series of power systems, is thenext evolution in our convection cooledrectifier series. This module provides thelatest advances in resonance switch modetechnology (softswitching). An onboard

microcontroller and an RS 485 data busprovide monitoring of basic functions, statusand identification information to the systemcontroller (GMC).

The CMP 3.48 rectifier module is optimizedfor telecom applications and is designed towork in numerous subrack/shelf configurations incorporating the GMCcontroller and varying distribution options.


• 48 VDC output

• Input over-voltage disconnection

• Thermal protection, with de-rating


• Hot-swappable

• Up to 91% efficient


• Low weight

• International Standards Compliance

Galero™ Power

System

CMP 3.48Rectifier Module

www.power-one.com

8/9/2019 68DCCAT

18/44

Input

Model CMP 3.48

Input Voltage

205-240V AC +10% single phase,

44-66Hz

(185-160V at reduced power output)

Current (max.) 91%

Tolerance Vout +/- 1.0%,

Transient

Response

+/- 5% at load variation

10-90% or 90-10%

recovery time 10ms

Load Sharing Typical 250VAC.

Indications

Green LED

Red LED

Power ON

High output

voltage/ shut down

Low voltage/

module failure

Audible

Noise

8/9/2019 68DCCAT

19/44

Description

The Galero™ Microprocessor Controller (GMC) from Power-One provides comprehensive monitoring and

control of the Galero power system. This digital controller monitors total system conditions including DC

voltage, rectifier current, rectifier temperature, system capacity, battery parameters and circuit breaker

status.

The GMC enables data storage of system configuration information such as battery type, installation date

and system commission date. Visual notification of alarm and warning conditions are indicated by front

panel LEDs, while descriptions of the alarms are provided through RS232 communication using PC-based

PowCom™ software package.

To meet individual site requirements, the GMC contains a Programmable Logic Unit that can be

programmed to monitor and control specified requirements. This allows actions to be set, alarms to be

triggered and outputs to be activated based on internal and external signal monitoring, comparing and

processing.

Features

User controls and interfaces:


• 40 event data logging

• Password controlled environment

• RS232 Interface and Form “C” dryalarm contacts

• Programmable routing alarm

• Programmable logic unit

GMCController Module

www.power-one.com


• Temperature compensation withprogrammable compensation factor





• Optional plug-in Ethernet interface (PNI module)

8/9/2019 68DCCAT

20/44

Input

Voltage 30-60V DC

Current

8/9/2019 68DCCAT

21/44

8/9/2019 68DCCAT

22/44

8/9/2019 68DCCAT

23/44

8/9/2019 68DCCAT

24/44

8/9/2019 68DCCAT

25/44

Description

The Power-One Xscend™ rectifier providesextremely reliable DC power in the highestpossible density. The module incorporatesthe latest in power monitoring solutionsthrough an internal microprocessor giving up

to the second updates to the systemcontroller and adjacent rectifiers. Thisguarantees tightly controlled load sharingamong rectifiers, and providing status andidentification information to the controller.

At only two rack units high, these compactrectifiers provide up to 1350W and fit up tofive rectifier modules in a 23in. rack or four modules in a 19in. rack. Designed withdiversity in mind, the Xscend rectifier is ableto operate in a complete range of indoor andoutdoor applications.

Features• Compact 2 rack unit height

• Front or mid-mountable• 208/240 single phase input

• Hot-swappable

• No adjustments required

• 90% typical efficiency

• Active and droop current sharing


Xscend Power

System

XR1448Rectifier Module

www.power-one.com

8/9/2019 68DCCAT

26/44

Input

Model XR1448

Input Voltage 180-264VAC (47-63Hz)

Current (max.) 9.3A @180VAC

Inrush Current 25A @ 25°C

Power Factor >0.98 typical

Fuse 12.5A- line, 12.5A- neutral

Connection FCI power connector™

EMCEN 61000-6-2, EN 61000-6-3,

FCC Part 15 Class B

Output

Model XR1448

Output Voltage 42-58VDC

Power (max.) 1350W

Current 25A

Efficiency 90% typical

ToleranceVout +/- 1.0%, constant

voltage regulation

Transient

Response+/- 4% recovery time 2ms

Load Sharing +/- 5%

Ripple

8/9/2019 68DCCAT

27/44

DescriptionThe Power-One Xscend™ Controller System (XCS) provides comprehensive monitoring

and control for Power-One’s Xscend DC power systems. This digital controller monitors

total system conditions including DC voltage, rectifier current, rectifier temperature,

system capacity, battery parameters and circuit breaker status.

The XCS enables data storage of system configuration information such as battery type,

installation date and system commission date. Visual notification of alarm and warning

conditions are indicated by front panel LEDs, while descriptions of the alarms are provided

through an LCD, or as an option, may be accessed remotely through a modem or a

Network Interface (PNI) module.

To meet individual site requirements, the XCS contains a logic operator that can be

programmed to monitor and control specified requirements. This allows actions to be set,

alarms to be triggered, and outputs to be activated based on internal and external signal

monitoring, comparing and processing.

FeaturesUser controls and interfaces:

• Simple menu-guided operation using frontpanel mounted pushbuttons and an LCD




• Multiple language options


XCSController

www.power-one.com







• Monthly data logging

8/9/2019 68DCCAT

28/44

Input

Voltage 18-72V DC

Current

8/9/2019 68DCCAT

29/44

8/9/2019 68DCCAT

30/44

Breaker Panels• Twenty positions for 5 to 100A

breakers

• Two positions for 125 to 250Abreakers

• A single position for a 450A or 525Abreaker

Low Voltage Disconnect• Optional Feature

• Provides protection against deepdischarge of batteries

• Emergency Power Off (EPO) switchprovided for emergency shutoff

• Remote contacts for EPO

Rectifier Shelves

• Interfaces with controller • 23” shelf allows up to 4rectifiers each

• Active current sharing• Single or three-phase input

DMAC Controller • Single point system voltage adjust

• Programmable timer for battery testor equalization

• Digital meters and test pointsmonitor plant voltages and current

• User-adjustable set points forunder/over voltage and low voltage

disconnect

NHS Rectifiers• 4 Rectifiers into each 3U 23” shelf• Available in 24 or 48VDC

• Thermal protection

• Fan cooled modules• Hot swappable• Low weight


System Components

Temperature Compensation• Works in conjunction with the DMAC

controller

• Automatically adjusts the float

voltage according to the ambienttemperature

• Sets off alarms when batterythermal runaway or sensor failure is

indicated

8/9/2019 68DCCAT

31/44

The Compac Power System is available in three different configurations, allowing customers to choose

the solution that is right for them. Each system uses the same basic components, systems include:


Compac Rack System™

Power System

48VDC 1200A System

The Compac full rack system

allows for up to 1200Aat 48V in a

single bay by using combinations

of distribution options. Each

rack is capable of holding up to

six rectifier shelves, a DMAC

controller panel, variousdistribution options and rear

connection points for external

battery strings.

48VDC 400A System


with battery shelves allows for up

to 400A at 48V in a single bay.

Each rack is capable of holding

up to five battery trays for 100 to

150 Ah battery reserve strings.

24VDC 800A System


without battery shelves allows for

up to 800A at 24V in a single bay.

Each rack is open at the bottom

to allow room for user installed

equipment.

8/9/2019 68DCCAT

32/44

8/9/2019 68DCCAT

33/44

Description

The Power-One NHS rectifier modulesprovide extremely reliable DC power output for use in our Compac™ series of power systems. NHS rectifier modulesare hot-swappable and provide a completeset of interface signals.

At only 3 rack units high, these compact

rectifiers allow for up to four modules ineach 23in. rack and provide up to 50A at48V or up to 100A at 24V. With full power available up to 50°C, these rectifiers areideal for any indoor and outdoor applications.

Features

• Compact 3 rack-unit height

• 24V and 48V rectifiers

• 50A output at 48V


• 180-264 single or three phase inputs

• Hot-Swappable, plug-and-play rectifiers

• High power density (9.8W/in3)

• High reliability, >700,000 hours MTBF

• Power factor correction

• Active current sharing


NHSRectifier Module

www.power-one.com

8/9/2019 68DCCAT

34/44

Input

Model NHS24/100 NHS48/50

InputVoltage 180 - 264V AC single phase, (50-60Hz)

Current 15A @ 230V 15A @ 230V

Soft Start 0.99 (50-100% load)

AC

Transient3000V, 2 Joules

Output

Mechanical

Dimensions5 x 5 x 12.25 in.

(12.7 x 12.7 x 31.1cm )

Weight 12.6 lbs.

Cooling Fan

Other Technical Data

Model NHS24/100 NHS48/50

Power (max.) 2400W 2400W

Output

Voltage25-29V DC 51-59V DC

Current (max.) 100A 50A

Efficiency(@ 40-90%Load)*

>86% >86%

Voltage

Regulation+/- 0.4%

TransientResponse

+/- 4% at load variation 10-90%or 90-10%, recovery time 10ms

Load Sharing

8/9/2019 68DCCAT

35/44

Features• Single point system voltage adjust

• Programmable timer for battery test orequalization

• Digital meters and test points monitor plantvoltages and current

• User-adjustable set points for under/over voltageand low voltage disconnect

DMACController

Description

The Power-One Digital Meter, Alarm and Control Panel (DMAC) provides comprehensivemonitoring and control for Power-One’s Compac™ power systems. This digital controller

monitors system conditions including DC voltage and load current, while providing a

variety of alarm and control functions.

DMAC features include user-configurable battery testing, measurement of battery voltage

and current & battery equalization.

Front panel LED’s for alarms, including:• Equalize alarm

• OV/UV alarm• Major alarm• Minor alarm• Rectifier fail

• Breaker alarm

www.power-one.com

8/9/2019 68DCCAT

36/44

Temperature Compensation

Other Technical Data

Operating

Temperature-0 to +50°C

Storage

Temperature-50 to +85°C

Humidity10-90% RH, operating, 5-95%

storage, non-condensing

Altitude

Range

13,000 ft., derate 7°C/100 ft.

above 8000 ft.

Overview

The temperature

compensation panel works in

conjunction with the DMACcontroller. Temperature

compensation automatically

adjusts the float voltage

according to the ambient

temperature.

Temperature

Compensation

Alarms

Alarms include temperature

delta, which indicates battery

thermal runaway and sensor

failure. In the event of a

sensor or panel failure, the

compensation defaults to the

normal float voltage set by thecontroller.

Interface


Display Digital amp and digital volt meters

Digital Meters 3.5 digits, +/-2% accuracy

UV/OV

Adjustment

22V/29V for 24VDC +/- 1.5V

44V/58V for 48VDC +/- 1.5V

Equalization &

Battery Test

Timer Range

0.5 seconds to 130 hours

Current

Measurement

DC Shunt

1200A:50mA

User Controls

Timer reset button

System voltage adjustment

Normal/Bypass test switch

Equalize/Battery test switch

Equalize Under/Over voltage adjustment

Undervoltage/Overvoltage

Connection

Points

System voltage test points

System amperage test points

www.power-one.com11V0005-050 DMAC V3.0

DMACController

Alarms

Alarms

Equalize alarm

OV/UV alarm

Major alarm

Minor alarm

Rectifier fail

Breaker alarm

8/9/2019 68DCCAT

37/44

8/9/2019 68DCCAT

38/44

8/9/2019 68DCCAT

39/44

8/9/2019 68DCCAT

40/44

8/9/2019 68DCCAT

41/44

Description

The Power-One PMP 25 rectifier providesextremely reliable DC power in a compactmodule. Digital interfaces areincorporated using an RS485 data bus tocommunicate with the system controller and adjacent rectifiers guaranteeingtightly controlled load sharing amongrectifiers, and providing status andidentification information to the controller.

At only 4 rack units high, these compactrectifiers allow for up to five modules ineach 23in. rack (4 units in 19in. rack)providing up to 250A at 48V or up to 550Aat 24V. With full power available up to65°C, these rectifiers are ideal for bothindoor and outdoor applications.

Features

• Compact 4 rack-unit height

• 24V and 48V rectifiers



• 208 / 240 single phase input

• Hot-swappable rectifiers• No adjustment required

• High efficiency, up to 91%

• Active current sharing


Integrity-One™ Full

Height System


www.power-one.com

8/9/2019 68DCCAT

42/44

Input

Model PMP 25.24 PMP 25.48

Input

Voltage

196 - 250V AC ±10% single phase,(44-66Hz)

176-160V AC at reduced output power

Current

(max.)

8/9/2019 68DCCAT

43/44

FeaturesUser controls and interfaces:

• Simple menu-guided operation using frontpanel mounted pushbuttons and an LCD




• Multiple language options


PCSController

Description

The Power-One Power Controller System (PCS) provides comprehensive monitoring and control for

a broad range of Power-One’s DC power systems. This digital controller monitors total system

conditions including DC voltage, rectifier current, rectifier temperature, system capacity, battery

parameters and circuit breaker status.

The PCS enables data storage of system configuration information such as battery type, installation

date and system commission date. In addition, the PCS is capable of monitoring up to 128 rectifiers

and 128 sub-controllers within a power system. Visual notification of alarm and warning conditions

are indicated by front panel LEDs, while descriptions of the alarms are provided through an LCD or

as an option may be accessed remotely through a modem or a Network Interface (PNI) module.

To meet individual site requirements, the PCS contains a logic operator that can be programmed to

monitor and control specified requirements. This allows actions to be set, alarms to be triggered, and

outputs to be activated based on internal and external signal monitoring, comparing and processing.







• Monthly data logging

www.power-one.com

8/9/2019 68DCCAT

44/44

Input

Voltage 18-72V DC

Current

68DCCAT

Documents

Transcript of 68DCCAT