45M Unit Sizes 2 - 7

CODE CATALOG # THIS DOCUMENT IS THE PROPERTY OF CARRIER CORPORATION AND IS DELIVERED UPON THE EXPRESS CONDITION THAT THE CONTENTS WILL NOT BE DISCLOSED OR USED WITHOUT CARRIER CORPORATION’S WRITTEN CONSENT. PRODUCT INFORMATION IS SUBJECT TO CHANGE WITHOUT NOTICE. 09/17/2021 JOB NAME JOB NUMBER LOCATION BUYER BUYER # REVISION DRAWING NUMBER SUBMISSION OF THESE DRAWINGS OR DOCU- MENTS DOES NOT CONSTITUTE PART PER- FORMANCE OR ACCEP- TANCE OF CONTRACT. VARIABLE VOLUME FAN TERMINAL UNIT 45M 1 OF 1 45M-202-2 SHEET D G W A F 1/2" FLANGE (2 PLCS) 1" FLANGE (2 PLCS) D Z Y X 11 7/8" 1 1/4" 15" H B CONTROL ENCLOSURE SEE NOTE 2 3/4" 1" HANGER BRACKET - (4 PLCS) SEE OPTIONAL FEATURES BELOW BACKDRAFT DAMPER 17" 1/2" DIAMETER DAMPER SHAFT 20" DD 1/2" PRIMARY AIR INLET ALLOW CLEARANCE FOR CONTROLS*** UNINSULATED COIL CASING 6 1/4" 3"** DISCHARGE INDUCED AIR INLET 34" 12 " DEPTH FOR ALL 1 & 2 ROW HOT WATER COILS WITH ACCESS DOORS* *(1 ROW) 8" (2 ROW) 9 3/16" PLAN VIEW – LEFT HAND BOX CONTROLS AND SENSORS NOT SHOWN INLET VIEW DISCHARGE VIEW 45M Unit Sizes 2 - 7 HOT WATER HEAT VARIABLE VOLUME FAN TERMINAL UNIT STANDARD FEATURES: 22 Ga. galvanized steel construction Steel control enclosure provided for electronic components 1/2” thick dual density fiberglass insulation meeting NFPA 90A and UL 181 safety requirements Field adjustable fan speed control 120V 208V/240V 277V multi-voltage, single speed, single phase, permanently lubricated PSC motors Four quadrant averaging cross flow sensor Factory mounted 1 or 2 row hot water coil with 5/8” O.D. connections, 1/2” O.D. copper tubes, 20 Ga. steel casing, and aluminum fins; 10 FPI 24 volt control transformer for electronic controls Removable bottom panel allows easy access to all internal components for maintenance Flanged discharge connection on hot water coil ETL listed; AHRI certified sound ratings OPTIONAL FEATURES: 20 Ga. galvanized steel construction Liners: 1” dual density fiberglass insulation 1/2” Foil encapsulated fiberglass insulation 1” Foil encapsulated fiberglass insulation 1/2" Cellular 1” Cellular Hot Water Coil Connections: Left Hand Coil access door Hanger brackets Right Hand Coil vent and drain Linear averaging sensor Induced air inlet attenuator Induced air filter, construction type (Unit Sizes 2-4 15”x15”x1, Unit Sizes 5-7 19”x17”x1”) Motor fusing Motor disconnect Dust tight control enclosure NOTE : 1. Dimensions are given in inches. 2. Digital or Analog control enclosure 20” x 11-7/8”, Pneumatic 17” x 15”. **6 1/16” long connection with vent & drain option. *** Check NEC for unit clearance requirements UNIT SIZE INLET SIZE P HP H H INDUCED AIR D D DISCHARGE Y X Z A B F G 2 06 1/10 29 15 13 13 5 7/8 4 7/8 12 1/2 15 7 1/2 6 7/8 1 3/4 2 08 1/10 29 15 13 13 7 7/8 4 7/8 12 1/2 15 7 1/2 6 7/8 1 3/4 3 08 1/10 29 15 13 13 7 7/8 4 7/8 12 1/2 15 7 1/2 6 7/8 1 3/4 3 10 1/10 29 15 13 13 9 7/8 4 7/8 12 1/2 15 7 1/2 6 7/8 1 3/4 4 10 1/4 29 15 13 13 9 7/8 4 7/8 12 1/2 22 7 1/2 6 7/8 1 3/4 4 12 1/4 29 15 13 13 11 7/8 6 7/8 12 1/2 22 7 1/2 6 7/8 1 3/4 5 12 1/2 37 17 3/4 17 15 3/4 11 7/8 6 7/8 15 22 8 7/8 9 1 7/8 5 14 1/2 37 17 3/4 17 15 3/4 13 7/8 6 7/8 15 22 8 7/8 9 1 7/8 6 14 1/2 37 17 3/4 17 15 3/4 13 7/8 6 7/8 15 24 1/2 8 7/8 9 1 7/8 6 16 1/2 37 17 3/4 17 15 3/4 15 7/8 6 7/8 15 24 1/2 8 7/8 9 1 7/8 7 16 3/4 37 17 3/4 17 15 3/4 15 7/8 6 7/8 15 24 1/2 8 7/8 9 1 7/8

Upload
others
Category

Documents
view
1
download
0

Embed Size (px):

Transcript of 45M Unit Sizes 2 - 7

CODE

CATALOG #

THIS DOCUMENT IS THE PROPERTYOF CARRIER CORPORATION AND ISDELIVERED UPON THE EXPRESSCONDITION THAT THE CONTENTSWILL NOT BE DISCLOSED OR USEDWITHOUT CARRIER CORPORATION’SWRITTEN CONSENT.

PRODUCT INFORMATION IS SUBJECT TO CHANGE WITHOUT NOTICE. 09/17/2021

JOB NAME JOB NUMBER LOCATION

BUYER BUYER # REVISION

DRAWING NUMBER

SUBMISSION OF THESEDRAWINGS OR DOCU-MENTS DOES NOTCONSTITUTE PART PER-FORMANCE OR ACCEP-TANCE OF CONTRACT.

VARIABLE VOLUMEFAN TERMINAL UNIT 45M

1 OF 145M-202-2SHEET

1/2" FLANGE(2 PLCS) 1" FLANGE

(2 PLCS)

11 7/8"

1 1/4"

15"

CONTROLENCLOSURESEE NOTE 2

3/4"

HANGER BRACKET - (4 PLCS)SEE OPTIONAL FEATURES BELOW

BACKDRAFTDAMPER

17"

1/2" DIAMETERDAMPER SHAFT

20"

DD1/2"

PRIMARYAIR INLET

ALLOW CLEARANCEFOR CONTROLS***

UNINSULATEDCOIL CASING

6 1/4"

3"**

DISCHARGE

INDUCEDAIR INLET

34"

12 " DEPTH FOR ALL 1 & 2ROW HOT WATER COILSWITH ACCESS DOORS*

*(1 ROW) 8"(2 ROW) 9 3/16"

PLAN VIEW – LEFT HAND BOX CONTROLS AND SENSORS NOT SHOWN

INLET VIEW

DISCHARGE VIEW

45M Unit Sizes 2 - 7 HOT WATER HEAT VARIABLE VOLUME FAN TERMINAL UNIT

STANDARD FEATURES:

22 Ga. galvanized steel construction Steel control enclosure provided for electronic components 1/2” thick dual density fiberglass insulation meeting NFPA

90A and UL 181 safety requirements Field adjustable fan speed control 120V 208V/240V 277V multi-voltage, single speed,

single phase, permanently lubricated PSC motors Four quadrant averaging cross flow sensor Factory mounted 1 or 2 row hot water coil with 5/8” O.D.

connections, 1/2” O.D. copper tubes, 20 Ga. steel casing,and aluminum fins; 10 FPI

24 volt control transformer for electronic controls Removable bottom panel allows easy access to all internal

components for maintenance Flanged discharge connection on hot water coil ETL listed; AHRI certified sound ratings

OPTIONAL FEATURES: 20 Ga. galvanized steel construction Liners:

1” dual density fiberglass insulation 1/2” Foil encapsulated fiberglass insulation 1” Foil encapsulated fiberglass insulation 1/2" Cellular 1” Cellular

Hot Water Coil Connections: Left Hand

Coil access door Hanger brackets

Right Hand Coil vent and drain Linear averaging sensor

Induced air inlet attenuatorInduced air filter, construction type(Unit Sizes 2-4 15”x15”x1, Unit Sizes 5-7 19”x17”x1”)

Motor fusing Motor disconnect Dust tight control enclosureNOTE :1. Dimensions are given in inches.2. Digital or Analog control enclosure 20” x 11-7/8”,

Pneumatic 17” x 15”.

**6 1/16” long connection with vent & drain option. *** Check NEC for unit clearance requirements

UNIT

SIZE

INLET SIZE P HPH H

INDUCED AIR DD D

DISCHARGE YXX Z AA B F G

2 06 1/10 29 15 13 13 5 7/8 4 7/8 12 1/2 15 7 1/2 6 7/8 1 3/4 2 08 1/10 29 15 13 13 7 7/8 4 7/8 12 1/2 15 7 1/2 6 7/8 1 3/4 3 08 1/10 29 15 13 13 7 7/8 4 7/8 12 1/2 15 7 1/2 6 7/8 1 3/4 3 10 1/10 29 15 13 13 9 7/8 4 7/8 12 1/2 15 7 1/2 6 7/8 1 3/4 4 10 1/4 29 15 13 13 9 7/8 4 7/8 12 1/2 22 7 1/2 6 7/8 1 3/4 4 12 1/4 29 15 13 13 11 7/8 6 7/8 12 1/2 22 7 1/2 6 7/8 1 3/4 5 12 1/2 37 17 3/4 17 15 3/4 11 7/8 6 7/8 15 22 8 7/8 9 1 7/8 5 14 1/2 37 17 3/4 17 15 3/4 13 7/8 6 7/8 15 22 8 7/8 9 1 7/8 6 14 1/2 37 17 3/4 17 15 3/4 13 7/8 6 7/8 15 24 1/2 8 7/8 9 1 7/8 6 16 1/2 37 17 3/4 17 15 3/4 15 7/8 6 7/8 15 24 1/2 8 7/8 9 1 7/8 7 16 3/4 37 17 3/4 17 15 3/4 15 7/8 6 7/8 15 24 1/2 8 7/8 9 1 7/8