400 HP Pump Lines API 610-OH6 - atlascisa.es€¦ · 400 HP Pump Lines API 610-OH6. ... •...
Transcript of 400 HP Pump Lines API 610-OH6 - atlascisa.es€¦ · 400 HP Pump Lines API 610-OH6. ... •...
400 HP Pump LinesAPI 610-OH6
Features
Performance
The LMV-341/343/346 and the BMP 348 have incorporated point emission and volute hydraulics with a morerobust 400-hp gearbox. This results in lower minimum flows, thereby extending the operating range of thepump.
Key Features
• Large 1- 3/4” (44.5mm) high speed journal bearings.
• High speed shaft with integral gear and balanced idler shaft with sleeved bearings to insure a low vibration unit and extended seal life.
• Lube oil reservoir located in both the idler shaft and the high speed shaft eliminates the need for the lube oil priming pump for vertical configurations.
• Roller bearings on the input shaft with a minimum of 100,000 hours L10 bearing life.
• Upgraded oil filter with a rating of 3 micrometers @ 200 Beta ratio, ISO extended code 14/12/10, resulting in extended bearing, seals and greater life.
• Internal lube oil pump with reversing capability providing bearing lubrication even if the pump motor is turningbackwards.
• 16 pitch spur gears manufactured to AGMA class 11 thereby increasing the AGMA rating.
• All gearbox split lines are sealed with o-rings eliminating an oil leak path.
• A new innovative labyrinth seal on the input shaft eliminating shaft wear and gearbox contamination.
• Integral lube oil filter manifold eliminating an oil leak path.
• LMV-346 discharge pressure ratings up to 3,000 psig. This rating varies with mechanical configuration and special metallurgies.
LMV-341/343/346
Mechanical Seal
Oil Fill Port
Oil Reservoir for Start-up Lubrication
Bi-directional LubeOil Pump ProvidesPressure FeedLubrication
16 Pitch Spur Gears
SundGardTM
Oil Filter3µm @ 200 ß
Idler ShaftJournal Bearings
ANSI3” 600# RF Flanges (900# and 1500# Optional)
Optional CentrifugalSeparator for CleanSeal Flush
Complete Family of Inducersfor Low NPSHA Applications
Single ThroatDiffuser forExtended OperatingRange with MinimumStable Flows to 15%(Volute Style forHigher Flows)
ANSI2” 600# RF Flanges(900# and 1500# Optional)
1-3/4” (44.5mm) HighCapacity JournalBearing
Integral Pinion Gearfor MinimizedVibration
Oil Reservoir forStart-upLubrication
Split Line O-ring Seals
Roller Bearings, 100,000 HRS L10
Coupled Input Shaft
Drive Gear
MechanicalSeal
Gearbox Designedto Full 400 hp Rating
Outline DrawingsLMV-341/343/346
with Vertical Stand(Optional)
BMP-341/348
118” (typical)
(3000 mm)100” (typical)(2540 mm)
48” (typical)4 sides
(1219 mm)
Width44.6”
(typical)(1132 mm)
34” (typical)(864 mm)
LMV-341/343/346(Standard Only)
26”(660mm)
25.7”(652mm)
01.09.10E, 5/2005 © Sundyne Corporation 2005 All Rights Reserved
• ANSIMAG • ANYSPEED • CASTER • GSP • HMD/KONTRO • MASO/SINE • SCMP • COMPRESSORS • SUNDYNE • SUNFLO •
Sundyne Corporation • 14845 W. 64th Avenue • Arvada, CO 80007 USA • +1-303-425-0800 • FAX: +1-303-425-0896 • www.sundyne.comSundyne Europe • Longvic Cedex, France • +33-380-383300 • FAX: +33-380-383371
www.sundyne.comVisit our website for a complete list of
manufacturers representatives, service centers, and direct offices
located throughout the world.
LMV-346