2011 Product Guide · 6 7 Residential Audio & Video Distribution Systems Distributed audio and...

2011 Product Guide

3

By Phone: 619-258-2000By Fax: 619-258-2135

NeoPro is proud to offer the professional integrator high quality products designed and manufactured in the USA. Our products offer a high-end fit and finish, high performance, and are some of the most compatible and easy to use products available to integra-tors. This is because they are designed for integration. All of our products come with the tools, drivers, support information, and mounting accessories the integrator needs to get the job done quickly.NeoPro continues to innovate the products and features you need today by having the vision of tomorrow’s challenges.

Want To Talk?

By Email: [email protected] Mail:

Neothings, Inc.1594 Fayette St

El Cajon, CA 92010

Want To Write?

Want To Read?Table Of Contents

Residential Audio & Video Distribution SystemsAvalon.....................................................8Borrego...................................................10Fallbrook.................................................12Gillespie..................................................13Juneau...................................................14Kingman.................................................15Concord (and Hornet).....................................16Delano....................................................18Eureka.....................................................19Ontario....................................................20Riverside..................................................21Sports Bar & Restaurant Systems Imperial....................................................24Lindbergh.................................................25Hawthorne...............................................26Quincy......................................................27Digital Video Distribution Systems LightSpider LP....................................................30LightSpider SRX.................................................32LightSpider 4TX..................................................34NeoStar.....................................................36Fiber Cable and Termination...........................38

www.neoprointegrator.com

54

Let’s centralize

all the AV gear,

less clutter in

each room.

We’ll use a home controller to send IR and

RS232 to the sources

All the audio

and video will

route through the

NeoPro matrix

switch

For your theater

room, we can do a 5.1 speaker system and

projector

The bedroom only needs a flat panel and the remote. Clean!Now all the

other 6 zones can share the same sources!

76

Residential Audio & Video Distribution

SystemsDistributed audio and video has al-ways been the sign of a truly integrat-ed home. Having all the sources cen-tralized allows the homeowner more flexibility on how they consume their media content, and at the same time, reduce visual equipment clutter in the living spaces.NeoPro has designed a range of dis-tribution equipment that are taylored for the high end home, and taylored for the high end residential integrator. Interface to the control system of your choice quickly and reliably with our many drivers and support tools.

98

• Power Inlet: IEC 320-C14• Input Voltage: 90-240VAC 50-60Hz, 8W

typical• Dimensions: Width: 17” Height: 3.45”

Depth 10.5” (not including removable feet)

• Weight: 12 lbs• Video bandwidth: 140MHz+ (full 1080p• Digital audio: PCM, LPCM, DD5.1, DTS• RS-232: 115.2K baud, full two way pro-

tocol• USB: Slave device, Windows driver

included, installs as virtual COM port at 115.2K baud

• Rear IR: 3.5mm mono jack for 5V or 12V blaster input, polarity insensitive

The Avalon is an 8 input matrix switch with 4 or 8 outputs designed for switching and distribution of high definition video and digital audio. This allows the centralization of all video source equipment, and dis-tribution throughout the home. For installations with a large number of sources with mixed optical and coax digital audio, the Avalon is a great choice.

Features

Specifications

avalonIR (rear)

• Highly visible Vacuum Fluorescent Display (VFD)

• 16 memories for storing and re-calling switching commands

• Front panel lockout and blackout• Black rack mount kit included

(silver on request)• Black or silver chassis with choice

of black or white front panels• IR codes available in several for-

mats for easy integration

• 8 inputs of component video• 8 inputs of optical and coax digi-

tal audio• 4 or 8 zone outputs• Independent audio and video

switching• Cross conversion between both

digital audio formats• NeoTouch™ front panel - no

moving parts to jam• Multiple control inputs - RS-232,

USB, IR detector (front) and wired

8

1110

• Power Inlet: IEC 320-C14• Input Voltage: 90-240VAC 50-60Hz, 13W typical• Dimensions: Width: 17” Height: 3.45” Depth

10.5” (not including removable feet)• Weight: 12 lbs• Video bandwidth: 140MHz+ (full 1080p)• Analog audio bandwidth: 20 Hz to 20KHz• Digital audio modes: PCM, LPCM, Dolby, DTS• Digital audio/C-video bandwidth: 20MHz

• RS-232: 115.2K baud, full two way protocol

• USB: Slave device, Windows driver included, installs as virtual COM port at 115.2K baud

• Rear IR: 3.5mm mono jack for 5V or 12V unmodulated blaster input, polarity insen-sitive

audio, which can then be fed directly into multizone amplifiers for whole house audio. The Borrego+ is like having three inde-pendent matrix switches in one unit. Component video, digital audio/com-posite video, and the analog audio can all be controlled separately, al-lowing for maximum flexibility.Powerful time based commands can create smooth audio fades to avoid abrupt changes in volume, making the Borrego+ a powerful part of your sys-tem design.

Features

Specifications

borrego+• 16 memories for storing and recall-ing switching commands

• Variable duration fade up/down• Discrete volume up/down IR codes

for each zone• Front panel lockout and blackout• Rack mount kit included• IR codes available in several for-

mats for easy integration

The Borrego+ matrix switch is the heart of a centralized multiroom audio and video system. The Borrego+ features a preamp section to allow volume, bass and treble control of the analog

• 8 inputs of component video• 8 inputs of digital audio• 8 inputs of left and right analog au-

dio, with Volume, Bass, and Treble for each output

• 4 or 8 zone outputs• Digital audio (SPDIF coax), doubles

as composite video matrix• Full non-blocking matrix - all outputs

can display the same signal or dif-ferent signals

• Independent audio and video switching - digital and analog audio can be switched independently

• NeoTouch™ front panel - no mov-ing parts to jam

• Multiple control inputs - RS-232, USB, IR detector (front) and wired IR (rear)

• Highly visible Vacuum Fluo-rescent Display (VFD)

1312

Features

Specifications

gillespie+fallbrook

Specifications• Power Inlet: IEC 320-C14• Input Voltage: 90-240VAC 50-60Hz, 8W typical• Dimensions: Width: 17” Height: 3.45” Depth

10.5” (not including removable feet)• Weight: 12 lbs• Video Bandwidth: 140MHz+ (full 1080p)• RS-232: 115.2K baud, full two way protocol• USB: Slave device, Windows driver included,

installs as virtual COM port at 115.2K baud• Rear IR: 3.5mm mono jack for 5V or 12V blaster

input, polarity insensitive

The Fallbrook and Gillespie+ to-gether form an 8x16 HD video and digital plus analog audio distribution system that is perfect for the larger home or small bar/restaurant. The Fallbrook has 8 inputs and 16 output zones of component video, while the Gillespie handles 8 inputs and 16 output zones of both digi-tal audio (SPDIF) and left and right analog audio. The Gillespie+ also features volume, bass, and treble controls for each output, so the out-put can be run directly into a multi-channel amplifier.


10.5” (not including removable feet)• Weight: 12 lbs• Analog audio bandwidth: 20 Hz to 20KHz• Digital audio modes: PCM, LPCM, Dolby, DTS• Digital audio/C-video bandwidth: 10MHz• RS-232: 115.2K baud, full two way protocol• USB: Slave device, Windows driver included,



• Component video (Fallbrook)• Left and right analog audio (Gillespie)• Volume, Bass, Treble for each output

(Gillespie)• Variable duration fade up/down (Gil-

lespie)• Digital audio (SPDIF coax), doubles as

composite video matrix (Gillespie)• Full non-blocking matrix • NeoTouch™ front panel - no moving

parts to jam.• Multiple control inputs - RS-232, USB, IR

detector and wired IR • Highly visible Vacuum Fluorescent Dis-

play (VFD)• 16 memory scenes• Front panel lockout and blackout• Rack mount kit included• IR codes available in several formats

for easy integration

1514

Features

Specifications

kingman+Juneau





The Juneau and Kingman+ together form a 12x16 HD video and digital plus analog audio distribution sys-tem that is perfect for the larger home or small bar/restaurant. The Juneau has 12 inputs and 16 output zones of component video, while the Kingman handles 12 inputs and 16 output zones of both digi-tal audio (SPDIF) and left and right analog audio. The Kingman+ also features volume, bass, and treble controls for each output, so the out-put can be run directly into a multi-channel amplifier.





• Component video (Juneau)• Left and right analog audio (Kingman)• Volume, Bass, Treble for each output

(Kingman)• Variable duration fade up/down (King-

man)• Digital audio (SPDIF coax), doubles as

composite video matrix (Kingman)• Full non-blocking matrix • NeoTouch™ front panel - no moving

parts to jam.• Multiple control inputs - RS-232, USB, IR

detector and wired IR • Highly visible Vacuum Fluorescent Dis-

play (VFD)• 16 memory scenes• Front panel lockout and blackout• Rack mount kit included• IR codes available in several formats

for easy integration

1716


10.5” (not including removable feet)• Weight: 12 lbs• Video bandwidth: 140MHz+ (full 1080p)• Analog audio bandwidth: 20 Hz to 20KHz• Digital audio modes: PCM, LPCM, Dolby, DTS• Digital audio/C-video bandwidth: 20MHz

• RS-232: 115.2K baud, full two way protocol


• Rear IR: 3.5mm mono jack for 5V or 12V unmodulated blaster input, polarity insen-sitive

Features

Specifications

concord+• Highly visible VFD Display• 16 memory scenes• Variable duration fade up/down• Discrete volume up/down IR codes

The Concord+ matrix switch is the heart of a centralized multiroom audio and video system and makes for an easy install or retrofit by using low cost Cat5 cables. The Concord+ features a preamp section to allow volume, bass and treble control of the analog audio, which can then be fed directly into multizone amplifiers for whole house audio. Powerful time based commands can create smooth audio fades to avoid

• Superior video performance com-pared to other Cat5 systems for reli-able HD picture up to 1,000’

• 8 inputs of component video• 8 inputs of digital audio• 8 inputs of left and right analog au-

dio, with Volume, Bass, and Treble for each output

• 8 zone outputs over 2x Cat5 cable• Full non-blocking matrix - all outputs

can display the same signal or dif-ferent signals

• Independent A/V switching• NeoTouch™ front panel - no mov-

ing parts to jam• RS-232, USB, IR front and rear

abrupt changes in volume, making the Concord+ a powerful part of your system design.At the end points, convert from Cat5 back to RCA connections with the Hornet receiver, available as both an in wall or surface mount version.The Hornet features an intelligent auto-equalizer circuit so there are no di-als to turn or adjustments to make to achieve picture perfect HD.No wall warts are ever needed since the Concord+ sends power to the Hor-

net receivers (as do all of our Cat5 ma-trix switches).

1918

Features

Specifications

eureka+delano





The Delano and Eureka+ together form an 8x16 HD video and digital plus analog audio distribution system that is perfect for the larger home or small bar/restaurant. At the end points, convert from Cat5 back to RCA connections with the Hor-net receiver, available as both an in wall or surface mount version.The Hornet features an intelligent auto-equalizer circuit so there are no di-als to turn or adjustments to make to achieve picture perfect HD.No wall warts are ever needed since the Delano and Eureka+ send power to the Hornet receivers (as do all of our Cat5 matrix switches).






• 8 inputs of component video (Dela-no)

• 8 inputs of digital audio (Eureka+)• 8 inputs of left and right analog au-

dio, with Volume, Bass, and Treble for each output (Eureka+)

• 16 zone outputs over 1x Cat5 cable• Full non-blocking matrix • RS-232, USB, IR front and rear• Highly visible VFD Display• 16 memory scenes• Variable duration fade up/down• Discrete volume up/down IR codes

(Eureka+)

2120

Features

Specifications

riverside+ontario





The Ontario and Riverside+ together form a 12x16 HD video and digital plus analog audio distribution system that is perfect for the larger home or small bar/restaurant. At the end points, convert from Cat5 back to RCA connections with the Hor-net receiver, available as both an in wall or surface mount version.The Hornet features an intelligent auto-equalizer circuit so there are no di-als to turn or adjustments to make to achieve picture perfect HD.No wall warts are ever needed since the Ontario and Riverside+ send power to the Hornet receivers (as do all of our Cat5 matrix switches).






• 12 inputs of component video (On-tario)

• 12 inputs of digital audio (River-side+)

• 12 inputs of left and right analog audio, with Volume, Bass, and Treble for each output (Riverside+)

• 16 zone outputs over 1x Cat5 cable• Full non-blocking matrix • RS-232, USB, IR front and rear• Highly visible VFD Display• 16 memory scenes• Variable duration fade up/down• Discrete volume up/down IR codes

(Riverside+)

2322

Sports Bar&

Restaurant Systems

Sports bar and restaurant video systems are an expanding market in the com-mercial integration segment. Franchise chains bring the opportunity for multiple installs and steady work for the integra-tor.NeoPro has designed a flexible stacking system that allows the system to grow in small increments, rather than a forklift upgrade when the owner decides to add more TVs than the original system design can handle.The integrator can even mix and match system types with both coax and Cat5 versions available.

2524

Features

Specifications

lindbergh+imperial

Specifications• Video bandwidth through matrix section: 140MHz+

(full 1080p)• Video bandwidth pass-throughs: +/- 0.8 dB over

150MHz• Power Inlet: IEC 320-C14• Input Voltage: 90-240VAC 50-60Hz, 8W typical• Dimensions: Width: 17” Height: 3.45” Depth 10.5”

(not including removable feet)• Weight: 12 lbs• Video Bandwidth: 140MHz+ (full 1080p)• RS-232: 115.2K

baud, full two way protocol



The Imperial is one of our most flex-ible matrices with 12 inputs and 8 outputs of component video, with input pass-through connections. The pass-through are high bandwidth buffered copies of all the input signals, before the matrix switch, which allow the connection to an additional matrix, adding another 8 outputs. Up to 12 Imperials can be stacked to create a full non-block-ing 12x96 matrix.

The Lindbergh is the audio equiva-lent of the Imperial, with 12 inputs of digital and analog audio, plus volume and tone control. Stacking Lindberghs can build up to a 12x96 audio distribution system.

• 12 inputs Component video (Impe-rial)

• Left and right analog audio (Lind-bergh)

• Volume, Bass, Treble for each out-put (Lindbergh)

• Variable duration fade up/down (Lindbergh)

• Digital audio (SPDIF coax), doubles as composite video matrix (Lind-bergh)

• Full non-blocking matrix • RS-232, USB, IR front and rear• 16 memory scenes





2726

Features

Specifications

quincy+hawthorne

Specifications• Video bandwidth through matrix section: 140MHz+

(full 1080p)• Video bandwidth pass-throughs: +/- 0.8 dB over

150MHz• Video bandwidth through 6 units: +/- 1 dB over

140MHz • Power Inlet: IEC 320-C14• Input Voltage: 90-240VAC 50-60Hz, 8W typical• Dimensions: Width: 17” Height: 3.45” Depth 10.5”

(not including removable feet)• Weight: 12 lbs• Video Bandwidth: 140MHz+ (full 1080p)• RS-232: 115.2K baud, full two way protocol• USB: Slave device, Windows driver included, installs

as virtual COM port at 115.2K baud


The Hawthorne is one of our most flex-ible matrices with 12 inputs and 8 outputs of component video, with input pass-through connections. All outputs are over Cat5. The pass-through are high band-width buffered copies of all the input signals, before the matrix switch, which allow the connection to an additional matrix, adding another 8 outputs. Up to 12 Hawthornes can be stacked to create a full non-blocking 12x96 matrix. At the end points, convert from Cat5 back to RCA connections with the Hornet receiver, available as both an in wall or surface mount version.

No wall warts are ever needed since the Hawthorne sends power to the Hornet receivers (as do all of our Cat5 matrix switches).

The Quincy+ is the audio equivalent of the Hawthorne, with 12 inputs of digital and ana-log audio, plus volume and tone control. Stacking Quincys can build up to a 12x96 audio distribution system.• 12 inputs Component video (Haw-

thorne)• Left and right analog audio (Quincy)• Volume, Bass, Treble for each output

(Quincy)• Variable duration fade up/down (Quin-

cy)• Digital audio (SPDIF coax), doubles as

composite video matrix (Quincy)• Full non-blocking matrix • RS-232, USB, IR front and rear• 16 memory scenes





2928

Digital Video Distribution

SystemsDigital video has proven to be a for-midable challenge to even the most seasoned integrators. At NeoPro, we understand the challenges, and have created the industry’s best solution with the all fiber optic based home in-frastructure.Digital video is more susceptible to problems with long runs to zones, im-proper power wiring, and outside in-terference.In addition to solving all of these prob-lems with a single strand of low cost fi-ber, we’ve given the integrator all the serial and IR control features they need in the automated home.

3130

• Power Inlet: 9VDC with supplied power supply• Input Voltage: 90-240VAC 50-60Hz, 9W typical• Dimensions: Width: 8.6” (includes mounting

flanges), Height: 1.6”, Depth 4.9”• Weight: 0.9 lbs each unit• Digital audio modes over the HDMI port: PCM,

LPCM, DD 5.1, DTS, up to 7.1 channels LPCM audio

• Aux analog stereo transported at 96KHz/24bit• Aux audio bandwidth: 20 Hz to 20KHz at +/-

0.5dB• Video modes: 480p to 1080p 50/60Hz HDTV, up

to 1920x1200 60Hz PC/DVI video• RS232 serial: 300 to 115.2K• Infrared (cable kit optional): 38-40KHz• Fiber spec: LC to LC multimode ‘simplex’

cable; recommend 62.5/125 micron for 0-500 feet, 50/125 micron from 500 to 1,000 feet.

FeaturesSpecifications lightspider-lp• Full EDID communications - EDID

display information is carried all the way through the system, so no need to ‘copy’ EDID or worry about it get-ting erased.

• RS232 serial (bidirectional)- allows remote control of any display that has an RS232 control port. Great for power on/off control of projectors and flat panels.

• Bidirectional IR - Use the LightSpider as both a forward IR path to con-trol

The LightSpider is an innovative fiber optic point to point bridge for long dis-tance transport of HDMI, audio, RS232 serial data, and infrared signals. It can carry this set of signals up to 1,000 feet (305 meters) over a single strand of low cost multimode fiber cable.

The LightSpider is able to communi-cate all of these signals over a single strand of either 62.5/125 micron or 50/125 micron multimode fiber cable. No additional Cat5 or additional fibers are required to achieve full HD with HDCP encryption and EDID communi-cations.• Go up to 1,000 feet without any

concern of signal degradation, HDCP dropouts and errors, or video ‘sparkles’.

• Up to 1080p 60Hz at max length - no derating of video capabilities as your cable gets longer.

the display device, or to capture IR commands in the zone and bring back to the source equipment.

• Auxiliary analog audio - use for lo-cal amp with in-wall speakers, or support audio to the display when audio over HDMI is not available.

3332

• Power Inlet: 5VDC with supplied power supply

• Input Voltage: 90-240VAC 50-60Hz, 5W typical

• Dimensions: Width: 6.38” (includes mounting flanges), Height: 0.76”, Depth 3.02”

• Weight: 0.9 lbs each unit• Digital audio modes over the HDMI

port: PCM, LPCM, DD 5.1, DTS, up to 7.1 channels LPCM audio

• Video modes: 480p to 1080p 50/60Hz HDTV, up to 1920x1200 60Hz PC/DVI video

• Infrared (cable kit optional): 38-40KHz

• Fiber spec: LC to LC multimode ‘simplex’ cable; recommend 62.5/125 micron for 0-500 feet, 50/125 micron from 500 to 1,000 feet.

FeaturesSpecifications lightspider srx

• Go up to 1,000 feet without any concern of signal degradation, HDCP dropouts and errors, or video ‘sparkles’.


• Full EDID communications - EDID display information is carried all the way through the system, so no need to ‘copy’ EDID or worry about it getting erased.

• Bidirectional IR - Use the LightSpider as both a forward IR path to control the display device, or to capture IR commands in the zone and bring back to the source equipment.

The LightSpider-SRX is a receive only version of the LightSpider-LP, but ultra thin so the flat panel can be mounted as flush as possible to the wall. Together with any of the other LightS-pider transmitters, the LightSpider-SRX transports HDMI and bidirectional IR up to 1,000 feet (305 meters) over a single strand of low cost multimode fiber cable. No additional Cat5 or additional fibers are required to achieve full HD with HDCP encryption and EDID com-munications.

3534

• Power Inlet: IEC320-C14• Input Voltage: 100-240VAC 50-60Hz, 35W typi-

cal• Dimensions: Width: 17”, Height: 1.74” (without

optional feet), Depth 10”• Weight: 7 lbs each unitDigital audio modes

over the HDMI port: PCM, LPCM, DD 5.1, DTS, up to 7.1 channels LPCM audio

• Aux analog stereo transported at 96KHz/24bit• Aux audio bandwidth: 20 Hz to 20KHz at +/-

0.5dB• Video modes: 480p to 1080p 50/60Hz HDTV, up

to 1920x1200 60Hz PC/DVI video• RS232 serial: 300 to 115.2K• Infrared (cable kit optional): 38-40KHz• Fiber spec: LC to LC multimode ‘simplex’

cable; recommend 62.5/125 micron for 0-500 feet, 50/125 micron from 500 to 1,000 feet.

FeaturesSpecifications lightspider 4txadditional fibers are required to achieve full HD with HDCP encryption and EDID communications. • Go up to 1,000 feet without any con-

cern of signal degradation, HDCP dropouts and errors, or video ‘sparkles’.


• Full EDID communications - EDID dis-play information is carried all the way through the system, so no need to ‘copy’ EDID or worry about it getting erased.

• RS232 serial (bidirectional)- allows remote control of any display that has an RS232 control port. Great for power on/off control of projec-tors and flat panels.

• Bidirection-al IR - Use the LightS-

The LightSpider 4TX is an innovative fiber optic point to point bridge for long dis-tance transport of HDMI, audio, RS232 se-rial data, and infrared signals. It can carry this set of signals up to 1,000 feet (305 meters) over a single strand of low cost multimode fiber cable. The LightSpider 4-TX consists of 4 LightSpiders in a single 1RU rack mount chassis for convenience of centrally locating all source equipment at one location.

The LightSpiders are able to commu-nicate all of these signals over a single strand of either 62.5/125 micron or 50/125 micron multimode fiber cable (one fiber per LightSpider). No additional Cat5 or

pider as both a forward IR path to con-trol the display device, or to capture IR commands in the zone and bring back to the source equipment.

• Auxiliary analog audio - use for local amp with in-wall speakers, or support audio to the display when audio over HDMI is not available.

3736

• Input Voltage: 90-240VAC 50-60Hz, 80W esti-mated Dimensions: W: 17”, H: 2RU/3.5”, D 13” Weight: 13 lbs estimated

• Digital audio modes over the HDMI port: PCM, LPCM, DD 5.1, DTS, up to 7.1 channels LPCM audio Video modes: 480p to 1080p 50/60Hz HDTV, up to 1920x1200 60Hz PC/DVI video

• RS232 serial: 300 to 115.2K baud Fiber spec: LC to LC multimode ‘simplex’ cable; recommend 62.5/125 micron, but 50/125 micron can also be used.

(Specifications are preliminary and subject to change)

FeaturesSpecifications

neostarend-point conversion of HDMI with HDCP.This allows the flexibility using mixed types of sources placed anywhere in the build-ing. As digital video interfaces change in the future, new LightSpiders willbecome available to interface into the NeoStar.• 14 source inputs (8 fiber video+audio,

plus 6 SPDIF audio only)• 12 zone outputs (8 fiber video+audio,

plus 4 SPDIF audio only) • Up to 1,000 feet @ 1080p 60Hz on all in-

puts and outputs without any concern of signal degradation, HDCP dropouts and errors, ground loops, interference or video ‘sparkles’.

• Full EDID management - EDID display

The NeoStar fiber optic matrix is an all digi-tal distribution system that breaks down all previous barriers when designing the digital home. Combined with new easy to use fiber cables and termination kits, it is now possible to distribute digital me-dia and control signals without having to worry about distance or signal quality limi-tations. The NeoStar features 1080p/60Hz performance with zero compression or processing delay.The NeoStar plays well with third party control systems, offering IP, RS232, and IR inputs for ease of implementation.The NeoStar is used in combination with the LightSpider TX and RX units to provide

information is managed by the inte-grator to ensure the source devices operate in the desired audio and video mode.

• RS232 and IR gateway to all sources and displays. Reach out from the Neo-Star to each LightSpider and send and receive IR and RS232 control signals.

• Industry standard LC fiber connector. Use with off the shelf premade fibers, or prewire and terminate in the field.

3938

Neo Part# Length (feet) Descrip6on32-‐00016 100 LC-‐LC simplex fiber, 50/125 ONFR riser rated, 3mm orange32-‐00017 200 LC-‐LC simplex fiber, 50/125 ONFR riser rated, 3mm orange32-‐00018 300 LC-‐LC simplex fiber, 50/125 ONFR riser rated, 3mm orange32-‐00019 500 LC-‐LC simplex fiber, 50/125 ONFR riser rated, 3mm orange32-‐00020-‐050 50 LC-‐LC simplex INVISAFIBER™ clear fiber, 50/125 0.9mm32-‐00020-‐100 100 LC-‐LC simplex INVISAFIBER™ clear fiber, 50/125 0.9mm32-‐00020-‐150 150 LC-‐LC simplex INVISAFIBER™ clear fiber, 50/125 0.9mm

32-‐00020-‐200 200 LC-‐LC simplex INVISAFIBER™ clear fiber, 50/125 0.9mm

NeoPro Part # Descrip/on Fiber Type

Jacket Type

Opera/ng Temperature

Flame Retardancy

Crush Resistance

Fiber Count Diameter

Installa/on Tensile Load

Opera/onal Tensile Load

Installa/on Min. Bend Radius

Long Term Min. Bend Radius Standards

Simplex 31-‐00002

Simplex 50/125um Plenum -‐20°C to +85°C UL Listed Type OFNP

500 N/cm 1 2.9mm 110 lbs 70 lbs 5 cm (2.0 in) 3 cm (1.2 in) GR-‐409-‐CORE, ICEA-‐S-‐83-‐596, TIA568, TIA-‐598

Duplex 31-‐00003

Duplex zipcord 50/125um Plenum -‐20°C to +85°C UL Listed Type OFNP

500 N/cm 2 2.9mm x 5.8mm

220 lbs 110 lbs 5 cm (2.0 in) 3 cm (1.2 in) GR-‐409-‐CORE, ICEA-‐S-‐83-‐596, TIA568, TIA-‐598

Invisifiber 31-‐00006

Simplex, Transparent

50/125um Clear PVC -‐20°C to +85°C NA NA 1 0.9mm 50 lbs 50 lbs 4 mm (<3/16") 1 cm (~3/8") NA

UltraLong 31-‐00007

Duplex zipcord, 10G OM3

50/125um Plenum -‐20°C to +85°C UL Listed Type OFNP

500 N/cm 2 2.9mm x 5.8mm

220 lbs 110 lbs 5 cm (2.0 in) 3 cm (1.2 in) GR-‐409-‐CORE, ICEA-‐S-‐83-‐596, TIA568, TIA-‐598

Rugged2 31-‐00008

2 fiber rugged, in/outdoor


2,100 N/cm 2 6.5mm 360 lbs 90 lbs 9.8 cm (3.9 in) 9.8 cm (3.9 in) GR-‐409-‐CORE, ICEA-‐S-‐83-‐596, TIA568, TIA-‐598

Rugged4 31-‐00009

4 fiber rugged, in/outdoor


2,100 N/cm 4 6.5mm 360 lbs 90 lbs 9.8 cm (3.9 in) 9.8 cm (3.9 in) GR-‐409-‐CORE, ICEA-‐S-‐83-‐596, TIA568, TIA-‐598

Rugged Indoor/Outdoor cable• Available as 2 or 4 fibers• Ideal for installations requiring an extremely

rugged and reliable cable design where maxi-mum mechanical and environmental protec-tion are required

• Flame-retardant for indoor installations (Plenum rated)

• High crush resistance eliminates the need for innerduct

• Standard 2.0mm subcables can be directly ter-minated with standard connectors.

• Design is ideal for direct pulling with mesh grips• Cable materials are indoor/outdoor – UV, wa-

ter and fungus resistant. Jacket highly chemi-cal resistant for installation in harsh industrial environments

Fiber cable and termination1 (simplex) and 2 (duplex) fibers• Flame-retardant for

indoor installations (Plenum rated)• Suitable for general purpose indoor use, both

short patch cables and long runs up to 1,000

INVISAFIBER transparent cable• Single fiber simplex with clear PVC 0.9mm

jacket• Super bend tolerant - As small as 4mm bend

radius during installation.• The perfect solution for retrofit jobs where there

is no clean way to get from the TV back to the head end.

10G/OM3 Ultra Long Run Cable• Flame-retardant for indoor installations (Plenum

rated)• Suitable for general purpose indoor use, patch

cables and long runs up to 1,500’

fiber cables from NeoPro are also a fast and cost effective way to deploy a fiber based video system. All cables are built to the highest quality standards and fully tested.

Pre-terminated Cables• Simplex fibers in both

standard or INVISAFIBER™

NeoPro can provide the integrator with all the tools and supplies needed for a successful installa-tion with fiber optics. Our INVISAFIBER™ clear PVC cable is the perfect solution for retrofit jobs. INVISAFIBER™ virtually dis-appears when installed along baseboards, crown molding, or masonry. Get as creative as you want going up and around doorways, ceilings, arch-ways, etc. and solve your customers toughest challenges.Fiber termination is now very easy with the AFL FAST termination kit. With very little prac-tice, the integrator can terminate fiber in as little as 2 minutes with no gluing and polishing.Ou r selection of bulk fibers can be ordered cut to length, and we offer a variety of types for most appli-cations. Preterminated

www.neoprointegrator.com

2011 Product Guide · 6 7 Residential Audio & Video Distribution Systems Distributed audio and...

Documents

Transcript of 2011 Product Guide · 6 7 Residential Audio & Video Distribution Systems Distributed audio and...