8/8/2019 2005 Up Ford Window Louvers Installation Manual Carid

1/2

IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE !Copyright 2010 by E&G Classics, Inc. All right reserved. The reproduction or utilization of this work in any form or any electronic, mechanical, or other means, no known or hereafter invented,

Including xerography, photocopying, and recording, and in any information storage retrieval system is forbidden without written permission of owners.

Part #: Complete 5049-3400-05

Notes to the Technician/Installer:E&G is proud to present this package to you and reminds you that for tech-nical information, contact Lynn Eash or Lee Clary at 410-381-4900. Do not

attempt the in stallation of any E&G product without first reading the detailed

instructions. E&G Classics will not warrant damaged parts or the vehi-

cle due to altered installation instructions.

J 11 HO P

Important information before you begin:

Ifthis E&G grille installation kit includes grille hole location template(s) to drill mounting holes in the vehicle,you MUST verify that the template(s) provided in this kit match the mounting pin locations on the grille(s).

Prior to drilling the mounting holes, place the assembled grilles mounting pins over the template(s) provided

and make sure that the pin and hole locations are the same. If they do not match, please call 410-381-4900

and ask for technical assistance. Thank you.

1. Place the louvers onto a clean, flat work area. Temporarily install

the mounting brackets (two (2) flat ones at the bottom). Then in-

stall the remaining five (5) bent brackets around the perimeter.

Then install the supplied 1/8 x 1/4 foam tape to the inside sur

face (where shown with white lines) breaking at the mounting

brackets.

2. Apply the .045 x 3/4 3M double-sided tapeon the upper edge

of lower half of the louver set as shown.

3. Thoroughly clean the rear window on the vehicle.

4. Once the mounting brackets have been removed, align the lou-

vers over the rear glass. Please pay close attention to the

alignment since this set consists of two individual louversections. The louvers should be pushed as forward as possi

ble on the upper glass area.

Copyright 2010 by E&G Classics, Inc. visit us online today at www.egclassics.com

2005-11 FORD MUSTANG 2 PC ABSEGX REAR WINDOW LOUVER Kit

TOOLS REQUIREDGlass cleaner, grease pencil, adhesive promoter, clean soft rags.

5. Lift up the sides of the louvers and insert the five (5) bent mount

ing brackets (1 per side & 3 along the top) making sure that the

bent edges are facing outwards and the mounting studs are pro-

truding through the existing holes in the louvers.

6. Once the five (5) bent brackets are in place, mark their locations

with a grease pencil.

7. Remove the two sections of louvers and mounting brackets.

8. Take the five (5) bent brackets and remove the red 3M tape

backing. Align the brackets to the markings made in Step #6 and

press firmly into place.

24INSTALLATION TIP: E&G Classics highly rec-comends the use of an adhesion promotor, such as

PRO BOND, in any application when applying 3M tape.

8/8/2019 2005 Up Ford Window Louvers Installation Manual Carid

2/2

9. Place only the lower section of the louver on the rear glass over

the previously installed lower brackets.

10. Remove the backing from the red 3M tape on the two flat brack-

ets with the 1/2 studs. Important: These are the only flat

brackets that have 1/2 studs.11. Place the stud through the upper hole & press the bracket down

firmly to the glass.

12. Repeat Step #10 with the two lower section flat brackets (3/8

studs) that are located just above the trunk (ensure that the

bracket/stud location is in the most foward location awayfrom the deck lid before pressing the brackets to the glass).

13. Remove the lower section of the louver.14. Place the top section of the louver in place ensuring that all

studs protrude through the mounting holes.15. Remove the backing from the 3M tape on the lower section of

the louvers that was attached in Step #2. Align the lower sectionto the mounted brackets and press the upper and the lower to-gether.

Copyright 2010 by E&G Classics, Inc. visit us online today at www.egclassics.com

12

Move the lower section brackets to the forward most positions in the

lower section of louvers before pressing the brackets to the glass!

E&G Classics Warranty Information:E&G Classics, Inc. warrants its chrome parts and products to be free from defects in ma-terial, workmanship or finish for Thirty-Six (36) months from the date of shipment by E&G.

This warranty is limited to the repair or replacement, at E&G Classics option, of the defec-

tive part or product.Full E&G Classics warranty information is available online @

www.egclassics.com. Just click on the product warranty icon.

For E&G Classic Product Returns:Please contact the authorized E&G Classics Dealer where you purchased our prod-

uct from in regards to any workmanship or warranty claims. All items returned toE&G Classics must have a return authorization number issued by us for inspection

or a defective product and or warranty issue. All merchandise sent back to E&G

Classics without proper paperwork or authorization will be rejected and returned.

Quanity: Description: Part Number:

1 Upper Louver Section 5049-340A-05

1 Lower Louver Section 5049-340B-05

1 Installation Hardware Kit 5049-3402-05

9 Nylon Thumb Nuts 1999-0387-00

3 15 Rolls of 1/8 x 1/4 Foam Tape 3999-9137-00

2 Flat Brackets 3/8 Studs 5049-3411-05

2 Flat Brackets 1/2 Studs 5049-3412-05

5 Bent Brackets 3/8 Studs 5412-3410-10

Part #5049-3400-05

2005-11 FORD MUSTANG EGX 2 PC REAR WINDOW LOUVER KIT

16. Secure the louvers using the supplied nylon thumb nuts.17. Finished installation.