2.) PIC Gauge Catalog

TABLE OF CONTENTS

Description Page General Information Product overview Color Tri-Fold Table of Contents 1-2 About Precision Instrument Company 3 Specifying Gauges: Questions to ask 4 PIC Part Numbering System 5 Section 1 Commercial Utility and Economy Gauges 100 Series Dry Utility Gauges 6 101D Bottom Connected 7 102D Back Connected 8 103D U-Clamp Panel Mount 9 104D Front Flanged Panel Mount 10 SE-101D Special Edition Bottom Mount 11 SE-102D Special Edition Back Mount 12 SEP-100 Series Plastic Case Gauges 13 Section 2 Stainless Case, Brass Internals - Liquid Filled 200 Series Liquid Filled Gauges 14 201L Bottom Connected 15 202L Back Connected 16 203L U-Clamp Panel Mount 17 204L Front Flanged Panel Mount 18 S215L Back Flanged Wall Mount 19 211D Dry but Fillable, Bottom Connected 20 212D Dry but Fillable, Back Connected 21 SEC-200 Series Economy Liquid Filled 22 SEC-201L Bottom Connected Liquid Filled 23 SEC-202L Back Connected Liquid Filled 24 SEC-203L U-Clamp Panel Mount Liquid Filled 25 SEC-204L Front Flanged Panel Mount Liq Filled 26 SE-201LFW-EZ Easy-Read Bottom Connect 27 S201L Single Scale (PSI only) Bottom Connect 28 Section 3 All Stainless Steel Gauges - Liquid Filled 300 Series All Stainless Steel Gauges 29 301LFW Bottom Connected 30 302LFW Back Connected 31 303LFW U-Clamp Panel Mount 32 304LFW Front Flanged Panel Mount 33 311D Dry but Fillable, Single Scale, Bottom 34 314D Front Flanged Panel Mount, Single Scale 35 S301L Single Scale Bottom Connected 36 SEC-301L Bottom Connected 37 Section 4 Process Gauges - Stainless Steel Internals 4001 4” Heavy Duty All Stainless Steel 38 4501 4 ½” Bottom Connected Process Gauge 39 4502 4 ½” Back Connected Process Gauge 40 4504, 6504 4 ½” or 6” Panel Mnt Process 41 4501-SC Stainless Steel Case Process Gauge 42 6001 6” Heavy Duty All Stainless, Bottom Conn 43 Section 5 Industrial and Special Application 601L Cast Brass Liquid Filled Bottom Connect 44 701L Plastic Case Liquid Filled, Bottom Conn 45 CONTRACTOR Gauge 46 115D 4 ½”, 6” or 8 ½”Industrial Gauges 47 LP Series Low Pressure Gauges 48 DPG Series Digital Pressure Gauge 49-50 BULK-HD 4 ½” Truck Mount Gauge 51 Valve Positioner Gauges 52 40MM Positioner Gauge 53 Panel Mount Gauges 54 501D-UNO Welding/Cryogenic Service Gauges 55 ALTITUDE Feet of Water Gauges 56 Ammonia Refrigeration Gauge Overview 57 Ammonia Gauge Specifications 58 401DFW Liquid Fillable Ammonia Gauges 59 401A Agricultural Ammonia Gauges 60 RECTANGLE (Edge) Gauge 61 GT Series Gas Test Gauges 62

TABLE OF CONTENTS (continued)

Description Page Section 5 Industrial and Special Application Hose Test Gauges 63 (continued) 509L Longwall Mining Gauge 64 102D-108 1” Mini Gauge 65 HEX Series 1” Dial High Pressure Gauge 66 SAE-201L Filled w/ SAE Hydraulic Connection 67 Spiral Tube Gauges 68 Fire Sprinkler Gauges 69 Section 6 Accessories Gauge Cocks and Air Valves 70 Pigtail Siphons 71 Test Plugs 72 Filter Type Pressure Snubber 73 Adjustable Pressure Snubber 74 Piston Type Pressure Snubber 75 Cooling Tower 76 Pressure Limiting Valve 77 Needle Valves Needle Valve Overview 78 Needle Valve Dimensions and Part Numbers 79 Diaphragm Seals Diaphragm Seal Descriptions and Part Numbers 80-81 Diaphragm Seal Overview 82 Mini Diaphragm Seals 83 Threaded Full Body Diaphragm Seals 84 Flanged Full Body Diaphragm Seals 85 Tri-Clamp Sanitary Type Diaphragm Seals 86 Sanitary Gauge and Seal Assemblies 87 Molded Gauge / Seal Assembly 88 Fill Fluids 89 Section 7 Thermometers Thermometer Overview 90 Bimetal Thermometers 2” Dial Back Connected Thermometers 91 3” or 5” Dial Back Connected Thermometers 92 3” or 5” Adjustable Angle Bimetal Thermometer 93 Miscellaneous Bimetal Thermometers 94 Bar-B-Q Grill Thermometers 95 Thermowells Thermowell Overview 96 Standard Thermowell Part Numbers 97 Thermowell Part Numbering System 98 Remote Dial Thermometers Vapor Actuated Thermometers 99 Gas Actuated Thermometers 100 Tridicators Tridicators for OEM, Industrial or Custom App. 101 2 ½” Dial OEM Tridicators 102 3 ¼” Dial Commercial Tridicators 103 3 ½” Dial Industrial Tridicators 104 Industrial Thermometers AS5 Series 9” Scale Industrial Thermometers 105 DSI Solar Digital Industrial Thermometers 106 160 Series 5” Scale Thermometers 107 Section 8 Miscellaneous Information Dial Increments 108 Standard Dials 108 Conversion Chart 110 Test and Certification of Pressure Gauges 111 Limited Warranty Information 112 Price List Price List 113-122

www.picgauges.com [email protected]

Vision

Our goal is to build long lasting relationships with our customers, come to know them and their customers as individuals – allowing us to apply our knowledge and expertise to give them the best product at the best price for their unique application while maintaining an unsurpassed level of service.

Precision Instrument Company began as a division of Engineered Specialty Products Inc in 1987. PIC began by developing a limited line of gauges and thermometers to satisfy the needs of OEMs that required high volumes of quality products at low costs. Since that time, PIC has developed a full line of quality instrumentation, We have several manufacturing facilities producing gauges, thermometers and accessories equal to or above industry standard specifications. We have combined our knowledge and experience with industry demands to produce quality products with pricing below that of our competitors and service exceeding expectations.

Why PIC?

1. No Stocking Requirements PIC has NO STOCKING REQUIREMENTS; you only stock what you need to support your unique

customer base. PIC has a very liberal exchange policy allowing for frequent inventory adjustments, which means you don’t keep dead inventory thus reducing your cost of inventory while increasing inventory turnover rate.

2. Delivery/Service PIC has approximately $6,000,000.00 finished goods in inventory – available or same day shipping with the added ability to make specials with shipment in 1-2 days. PIC also has a complete inventory of diaphragm seals with the facilities to do in-house assembling and filling for shipments in 1-2 days plus gauge repair capabilities. All of this adds up to unsurpassed service and delivery, reducing the need to search for product, reducing the chances of lost orders due to delivery, reducing customer aggravation and reducing costs due to expedite charges and air freight shipments.

3. Competitiveness PIC has the proven ability to compete against all manufacturers and win! After over 20 years of competing with every major manufacturer, we have learned what it takes to beat the competition on every level – PIC can show you why you should never lose an order to the competition with our products, pricing and service.

4. Profitability At PIC, we understand the bottom line is profit. Increased competition in the market place has forced smaller profit margins for most companies to remain competitive. We continue to keep pricing lower than industry averages, allowing you to maintain reasonable profit margins.

5. Sales Support: PIC has long-term, proven relationships between our inside and outside sales staff and our customers which have allowed us to know each of our customers and their requirements individually - which has been very effective in obtaining and maintaining new and old business. There are very few accounts we have actively pursued that we have not been able to close.

6. Conclusion PIC’s Lower prices, quicker deliveries and lower inventory costs add up to higher profit margins and less competition.

Toll Free (888) 650-6923 Fax (770) 429-0795

PRESSURE GAUGE SELECTION

Specifications and options to consider when selecting pressure gauge(s)

1.) Dial Size Standard available dial sizes: 1”, 1 ½”, 2”, 2 ½”, 3 ½”, 4”, 4 ½”, 6” or 8 ½” Other dial sizes are available

Determine dial size by measuring across the diameter of the face

2.) Connection Location Bottom connected (lower mount) is the most common Center back mount (or lower back mount) is also considered standard Other locations can be supplied by special request

3.) Connection Size Typical sizes (expressed in NPT sizes) 1/8”, 1/4", or 1/2" Other sizes and types of connections are available upon request Please call to check if you have special requirements

4.) Mounting Stem mount (No Special Mounting Hardware Required) Panel mount – U-Clamp Panel mount – Front Flange Wall mount – Back Flange

5.) Material of Wetted Parts (Refers to all parts in contact with process fluid – Please check corrosion guides for suitable materials)

Most typical applications – brass or bronze tube and socket More severe applications may require stainless steel – 316SS is standard (Occasionally Monel will be necessary) If none of these are adequate for the application, a diaphragm seal will be required

6.) Dry Or Liquid Filled Dry gauges are suitable for most applications Glycerine filled gauges will be specified for applications with pulsation or vibration

or for other reasons based on customer preference Silicone filling may be required where process conditions don’t allow the use of glycerine filling, such

as temperature extremes or concerns regarding interaction with process Other fluids are available please call if above are not suitable

7.) Case Material (Typically determined by size and type specified above) Some industry standard materials & gauges types are listed: Black painted steel case – dry type, utility and industrial gauges Aluminum – process and industrial gauges Stainless steel – liquid filled and process gauges Phenolic/Polypropylene – process gauges

8.) Range Typically specified in PSI for pressure from 0 up to 15,000 PSI or Inches or mercury vacuum from 0 to 30” of mercury vacuum Compound ranges have both pressure and vacuum Other available scales: Metric reading (Bar, kPa, Kg/cm2, mPa)

Low pressure (inches of water or milli-bar) Altitude (feet of water or meters of water)

Force (tons on ram) And many more Dual scale: Standard with metric ranges or

Pressure with equivalent altitude, force, etc.

9.) Accuracy Typically will be determined by size and type of gauge determined above Accuracy grades are specified by ASME standards

10.) Certification/Cleaning Conformance Certificate – states gauges meets catalog specifications and/or order requirements Certificate of Accuracy – gauge is tested up and down scale with accuracy and % of error noted Special – by customer request – particular aspect of gauge certified to meet customer requirement Oxygen Cleaning – gauge cleaned and bagged – suitable for oxygen service Special – by customer request – gauge cleaned to particular cleanliness level required by customer

11.) Other It is a good idea to always ask if there are any other special process conditions to be aware of, or of any special needs they have, occasionally your customer will have unusual requirements or uncommon requests

Note: Although this is a good model to follow this does not guarantee you will get all critical information, or, that with the information supplied you will get the exact item your customer wants.

PART NUMBERING SYSTEM

1= Steel Case W/Chrome Ring Brass Internals 2= Stainless Steel Case Brass Internals 3= Stainless Steel Case 316 SS Internals 4= Ammonia Gauge Steel Socket, 316 SS Tube 5= Plated Brass Case Brass Internals 6= Forged Brass Case Brass Internals 7= Black Poly Case Brass Internals

TYPE SERIES

SPECIAL FEATURES 0= Standard Gauge 1= Removable Ring, Adjustable Pointer

MOUNTING STYLE 1= Bottom Connection Stem Mounted 2= Back Connection Stem Mounted 3= Back Connection U-Clamp, Panel Mount 4=Back Connection Front Flanged, Panel Mount 5= Bottom Connection Back Flanged, Wall Mount

TYPE FILLING D= Dry Gauge- Not Filled L= Glycerine Filled S= Silicone Filled

8= ⅛”npt male 4= ¼’’npt male 2= ½’’npt male

A = 30/0”hg Vac CB = 30/0/15 CC = 30/0/30 CD = 30/0/60 CE = 30/0/100 CF = 30/0/150 CH = 30/0/300 B = 0-15 PSI C = 0-30 PSI D = 0-60 PSI E = 0-100 PSI F = 0-160 PSI G = 0-200 PSI H = 0-300 PSI I = 0-400 PSI J = 0-500 PSI K = 0-600 PSI L = 0-800 PSI M = 0-1000 PSI N = 0-1500 PSI O = 0-2000 PSI P = 0-3000 PSI Q = 0-4000 PSI R = 0-5000 PSI S = 0-6000 PSI U = 0-10,000 PSI V = 0-15,000 PSI W = 0-20,000 PSI

CONN. SIZE

RANGES

10= 1’’ Diameter 15= 1 ½’’ Diameter 20= 2” Diameter 25= 2 ½” Diameter 35= 3 ½” Diameter 40= 4” Diameter 45= 4 ½” Diameter 60= 6” Diameter 85= 8 ½” Diameter

2 = St. Steel Case Brass Internals 0 = Standard Gauge 1 = Stem Mount-Bottom Connect L = Glycerine Filled - 2 5 = 2 ½” Dial Size 4 = ¼” Male Npt Threads E = 0/100 Psi

DIAL SIZE

EXAMPLE: “201L-254E ”

100 SERIES UTILITY GAUGE

Specifications:

• Steel case with chrome bezel • Brass internals and connection • Dry non-fillable • 3-2-3 % accuracy

Available Dial Sizes: • 1”, 1 ½”, 2”, 2 ½”, 3 ½”, 4 ½”

Available Connection Sizes: • ⅛“mnpt on 1 ½” and 2" • ¼” mnpt on 2" thru 4"

101D

102D

103D

104D101D (BLACK CASE)

1 ½” 2" 2 ½” 3 ½” 4 ½” A 1.64”/42mm 2.07”/53mm 2.50”/63mm 3.53”/90mm 4.89”/124mm B .93”/24mm 1.03”/26mm 1.17”/30mm 1.14”/29mm 1.16”/29mm C .63”/16mm .83”/21mm .86”/22mm 1.02”/26mm 1.16”/30mm D 2.27”/58mm 2.90”/74mm 3.36”/85mm 4.55”/116mm 6.05”/154mm

E ⅛”NPT ⅛”or ¼” NPT ¼” NPT ¼” NPT ¼” NPT

102D (BLACK CASE) 1” 1 ½” 2” 2 ½” 3 ½” 4 ½”

A .99”/25mm 1.64”/42mm 2.07”/53mm 2.50”/63mm 3.97”/101mm 4.5”/114mm B .64”/16mm .93”/24mm 1.03”/26mm 1.17”/30mm 1.19”/30mm 1.34”/34mm C .46”/12mm .63”/16mm .83”/21mm .86”/22mm .83”/21mm .84”/21mm D 1.10”/28mm 1.56”/39mm 1.86”/47mm 2.03”/52mm 2.02”/51mm 2.18”/55mm

E 1/8 NPT 1/8 NPT 1/8” or 1/4" 1/4 NPT 1/4 NPT 1/4 NPT

103D (CHROME CASE) 1 ½” 2" 2 ½” 3 ½”

A 1.82”/46mm 2.31”/59mm 2.68”/68mm 3.97”/101mm B 1.03”/26mm 1.17”/30mm 1.19”/30mm 1.19”/30.16mm C .61”/15mm .73”/18.5mm .76”/19mm .83”/21mm D 1.64”/42mm 1.90”/48.5mm 1.95”/50mm 2.02”/51mm E ⅛”NPT ⅛”or ¼” NPT ¼” NPT ¼” NPT

G 1.59”/40mm 2.02”/51mm 2.46”/63mm 3.59”/91mm

104D (CHROME CASE) 1 ½” 2" 2 ½” 3 ½”

A 1.82”/46mm 2.31”/59mm 2.68”/68mm 3.97”/101mm B 1.03”/26mm 1.17”/30mm 1.19”/30mm 1.19”/30.16mm C .61”/15mm .73”/18.5mm .76”/19mm .83”/21mm D 1.64”/42mm 1.90”/48.5mm 1.95”/50mm 2.02”/51mm E ⅛”NPT ⅛”or ¼” NPT ¼” NPT ¼” NPT F 2.47”/63mm 2.81”/71mm 3.44”/87mm 4.30”/109mm

G 1.61”/41mm 2.02”/51mm 2.46”/63mm 3.59”/91mm

• An inexpensive utility gauge for the broad commercial and industrial markets. • Suitable for air, water, oil, gas or any other media not corrosive to brass. • Other connection locations, mounting styles and accessories available. • Ready for immediate shipment upon request.

101D BOTTOM CONNECTED

SPECIFICATIONS: • AVAILABLE DIAL SIZES: 1 ½”, 2”, 2 ½”, 3 ½”, 4 ½”

• AVAILABLE CONNECTION SIZES: ⅛”NPT on 1 ½” and 2”Dial Sizes ¼”NPT on 2" Thru 4 ½”Dial Sizes

• Black Steel Case, Chrome Bezel • Phosphor Bronze Bourdon Tube • Brass Socket • Plastic Lens • 3-2-3 % Accuracy • Dry Non-Fillable • Ambient Temperature: -50 to 160˚F • Dual scale: PSI & Bar (x100=kpa) standard

Single scale: PSI only available Other: by special request

RANGE CODE Major Inc. Minor inc. 30/0"VAC A 5” hg .5” hg 30/0/15 CB 10”hg / 5 psi 1”hg / .5 psi 30/0/30 CC 10”hg / 10 psi 1”hg / 1 psi 30/0/60 CD 10”hg / 10 psi 2”hg / 1 psi 30/0/100 CE 30”hg / 20 psi 5”hg / 2 psi 30/0/150 CF 30”hg / 20 psi 5”hg / 2 psi 30/0/300 CH 30”hg / 50 psi 10”hg / 5 psi 0/15 B 2 PSI .2 PSI 0/30 C 5 PSI .5 PSI 0/60 D 10 PSI 1 PSI 0/100 E 20 PSI 2 PSI 0/160 F 20 PSI 2 PSI 0/200 G 40 PSI 5 PSI 0/300 H 50 PSI 5 PSI 0/400 I 50 PSI 5 PSI 0/600 K 100 PSI 10 PSI 0/1000 M 200 PSI 20 PSI 0/1500 N 200 PSI 20 PSI 0/2000 O 400 PSI 50 PSI 0/3000 P 500 PSI 50 PSI 0/5000 R 1000 PSI 100 PSI 0/6000 S 1000 PSI 100 PSI 0/10,000 U 2000 PSI 200 PSI

A B C D E 1 ½" In. 1.64" .93” .63” 2.27” 1/8” Dial MM 42 24 16 58 MNPT

2" In. 2.07" 1.03” .83” 2.90” 1/8” or 1/4 Dial MM 53 26 21 74 MNPT

2 ½" In. 2.5" 1.17” .86” 3.36” 1/4 Dial MM 63 30 22 26 MNPT

3 ½" In. 3.53" 1.14” 1.02” 4.55” 1/4 Dial MM 90 29 26 116 MNPT

4 ½" In. 4.89" 1.16” 1.16” 6.05” 1/4

Dial MM 124 29 30 154 MNPT

• An inexpensive utility gauge for the broad commercial and industrial markets. • Suitable for air, water, oil, gas or any other media not corrosive to brass. • Other connection locations, mounting styles and accessories available. • Ready for immediate shipment upon request.

102D BACK CONNECTED


A B C D E In. .99" .64” .46” 1.10” 1"

Dial MM 25 16 12 28 1/8”

MNPT

In. 1.64” .93” .63” 1.56” 1 ½”Dial MM 42 24 16 39

1/8” or 1/4 MNPT

In. 2.07” 1.03” .83” 1.86” 2" Dial MM 53 26 21 47

1/4 MNPT

In. 2.50” 1.17” .86” 2.03” 2 ½”Dial MM 63 30 22 52

1/4 MNPT

In. 3.97” 1.19” .83” 2.02” 3 ½"Dial MM 101 30 21 51

1/4 MNPT

In. 4.5” 1.34” .84” 2.18” 4 ½”Dial MM 114 34 21 55

1/4 MNPT

SPECIFICATIONS: • AVAILABLE DIAL SIZES: 1 ½”, 2”, 2 ½”, 3 ½”, 4 ½”


• Black Steel Case, Chrome Bezel • Phosphor Bronze Bourdon Tube • Brass Socket • Plastic Lens • 3-2-3 % Accuracy • Dry Non-Fillable • Ambient Temperature: -50 to 160˚F • Dual scale: PSI & Bar (x100=kpa) standard


103D PANEL MOUNT

• A durable dry type utility gauge designed to look good from the front or back of the panel. • These gauges are suitable for air, water, oil, gas or any other media not corrosive to brass. • Other connection locations, mounting styles and accessories are also available. • Ready for immediate shipment upon request.


A B C D G E In. 1.82 1.03 .61 1.64 1.59 1 ½”

Dial MM 46 26 15 42 40 1/8”

MNPT

In. 2.31 1.17 .73 1.90 2.02 2" Dial MM 59 30 18.5 48.5 51

1/8” or 1/4 MNPT

In. 2.68 1.19 .76 1.95 2.46 2 ½”Dial MM 68 30 19 50 63

1/4 MNPT

In. 3.97 1.19 .83 2.02 3.59 3 ½"Dial MM 101 30 21 51 91

1/4 MNPT

SPECIFICATIONS: • AVAILABLE DIAL SIZES: 1 ½”, 2”, 2 ½”, 3 ½”


• Chrome Plated Steel Case, Chrome Bezel • Phosphor Bronze Bourdon Tube • Brass Socket • Plastic Lens • 3-2-3 % Accuracy • Dry Non-Fillable • Ambient Temperature: -50 to 160˚F • Dual scale: PSI & Bar (x100=kpa) standard


104D PANEL MOUNT

• A durable dry type utility gauge designed to look good from the front or back of the panel. • These gauges are suitable for air, water, oil, gas or any other media not corrosive to brass. • Other connection locations, mounting styles and accessories are also available. • Ready for immediate shipment upon request.


A B C D F G E In. 1.82” 1.03” .61” 1.64” 2.47” 1.61” 1 ½”

Dial MM 46 26 15 42 63 41 1/8”

MNPT

In. 2.31” 1.17” .73” 1.90” 2.81” 2.02” 2" Dial MM 59 30 18.5 48.5 71 51

1/8 or 1/4 MNPT

In. 2.68” 1.19” .76” 1.95” 3.44” 2.46” 2 ½” Dial MM 68 30 19 50 87 63

1/4 MNPT

In. 3.97” 1.19” .83” 2.02” 4.30” 3.59” 3 ½" Dial MM 101 30.2 21 51 109 91

1/4 MNPT

SPECIFICATIONS: • AVAILABLE DIAL SIZES: 1 ½”, 2”, 2 ½”, 3 ½” • AVAILABLE CONNECTION SIZES:

⅛”NPT on 1 ½” and 2”Dial Sizes ¼”NPT on 2" Thru 3 ½”Dial Sizes

• Chrome Plated Steel Case, Chrome Bezel • Phosphor Bronze Bourdon Tube • Brass Socket • Plastic Lens • 3-2-3 % Accuracy • Dry Non-Fillable • Ambient Temperature: -50 to 160˚F • Dual scale: PSI & Bar (x100=kpa) standard


RANGE CODE

SE-101D BOTTOM CONNECTED

SE-101D

1 1/2" 2" 2 1/2" 3 1/2" 4 1/2" A 1.64”/42mm 2.07”/53mm 2.50”/63mm 3.53”/90mm 4.89”/124mmB .93”/24mm 1.03”/26mm 1.17”/30mm 1.14”/29mm 1.16”/29mm C .63”/16mm .83”/21mm .86”/22mm 1.02”/26mm 1.16”/30mm D 2.27”/58mm 2.90”/74mm 3.36”/85mm 4.55”/116mm 6.05”/154mmE 1/8npt 1/8 or 1/4npt 1/4npt 1/4npt 1/4npt

CODE RANGE MAJOR IN MINOR IN C 0/30 PSI 5 psi .5 psi

With 2 Bar (x100 = kPa) .5 bar .05 bar D 0/60 PSI 10 psi 1 psi

With 4 Bar (x100 = kPa) 1 bar .1 bar E 0/100 PSI 20 psi .2 psi

With 7 Bar (x100 = kPa) 1 bar .1 bar F 0/160 PSI 20 psi .2 psi

With 11 Bar (x100 = kPa) 2 bar .2 bar G 0/200 PSI 40 psi 5 psi

With 14 Bar (x100 = kPa) 2 bar .2 bar H 0/300 PSI 50 psi 5 psi

With 20 Bar (x100 = kPa) 5 bar .5 bar

PART NUMBER SYSTEM SE-101D-

Dial Size • 15 = 1 ½” • 20 = 2” • 25 = 2 ½” • 35 = 3 ½” • 45 = 4 ½”

Connection Size • 8 = 1/8” MNPT • 4 = 1/4" MNPT

SPECIFICATIONS: • AVAILABLE DIAL SIZES: 1 ½”, 2”, 2 ½”, 3 ½”, 4 ½” • AVAILABLE CONNECTION SIZES:

1/8”NPT on 1 ½”Dial Size 1/4”NPT on 2" Thru 4 ½”Dial Sizes

• Black Steel Case, Black Bezel • Phosphor Bronze Bourdon Tube • Brass Socket • Large Orifice / No Restrictor (less likely to clog) • Glass Lens • 3-2-3 % Accuracy • Dry Non-Fillable • Ambient Temperature: -50 to 160˚F • Dual scale: PSI & Bar (x100=kpa) standard


SE-102D BACK CONNECTED

SE-102D

CODE RANGE MAJOR IN MINOR IN 5 psi .5 psi C

With0/30 PSI

2 Bar (x100 = kPa) .5 bar .05 bar 10 psi 1 psi D

With0/60 PSI

4 Bar (x100 = kPa) 1 bar .1 bar 20 psi .2 psi E

With0/100 PSI

7 Bar (x100 = kPa) 1 bar .1 bar 20 psi .2 psi F

With0/160 PSI

11 Bar (x100 = kPa) 2 bar .2 bar 40 psi 5 psi G

With0/200 PSI

14 Bar (x100 = kPa) 2 bar .2 bar 50 psi 5 psi H

With0/300 PSI

20 Bar (x100 = kPa) 5 bar .5 bar

PART NUMBER SYSTEM SE-102D -

Dial Size • 15 = 1 ½” • 20 = 2”

RANGE CODE

CONNECTION SIZE • 8 = 1/8” MNPT • 4 = 1/4 MNPT

SPECIFICATIONS: • AVAILABLE DIAL SIZES: 1 ½”, 2”, 2 ½”, 3 ½”, 4 ½” • AVAILABLE CONNECTION SIZES:

1/8”NPT on 1 ½”Dial Size 1/4”NPT on 2" Thru 4 ½”Dial Sizes

• Black Steel Case, Black Bezel • Phosphor Bronze Bourdon Tube • Brass Socket • Large Orifice / No Restrictor (less likely to clog) • Glass Lens • 3-2-3 % Accuracy • Dry Non-Fillable • Ambient Temperature: -50 to 160˚F • Dual scale: PSI & Bar (x100=kpa) standard


DIAL SIZE A B C D E 1 1/2" INCHES 1.64" .93” .63” 1.56” 1/8”NPT

MM 42mm 24mm 16mm 39mm 1/8”NPT 2" INCHES 2.07" 1.03” .83” 1.86” MM 53mm 26mm 21mm 47mm

¼” OR 1/8” NPT

SEP-100 SERIES PLASTIC CASE These gauges are designed for applications where plastic cases and brass internals are suitable for use. The abs case and polycarbonate lens offer great appearance and resistance to weather and corrosion attack. Typical applications include water, air and oil.

BOTTOM BACK RANGE SEP-101D-204A SEP-102D-204A 30”HG VAC SEP-101D-204B SEP-102D-204B 0/15 PSI SEP-101D-204C SEP-102D-204C 0/30 PSI SEP-101D-204D SEP-102D-204D 0/60 PSI SEP-101D-204E SEP-102D-204E 0/100 PSI SEP-101D-204F SEP-102D-204F 0/160 PSI SEP-101D-204G SEP-102D-204G 0/200 PSI SEP-101D-204H SEP-102D-204H 0/300 PSI

SEP-102D SEP-101D Dim Description SEP-101D SEP-102D

A Case Overall Diameter 2.06” / 53mm 2.06” / 53mm B Depth Of Case 1.15” / 29.4mm 1.13” / 28.7mm C Stem Length (Including Threads) .80” / 20mm .80” / 20mm D Overall Height(Bottom) / Depth(Back) 2.82” / 72mm 1.8” / 45.8mm E Wrench Flats .55” / 14mm .55” / 14mm

SPECIFICATIONS: • 2”Dial Size • ¼”NPT Connection • Plastic Case • Phosphor Bronze Bourdon Tube • Brass Socket • Plastic Lens • 3-2-3 % Accuracy • Dry Non-Fillable • Ambient Temperature: -40 to 140˚F • Dual scale:

Easy Read PSI & Bar (x100=kpa) standard Single scale: PSI only available Other: by special request

200 SERIES LIQUID FILLED GAUGE

Specifications:

• Stainless steel case and bezel • Brass internals and connection • Liquid filled (dry available) • 3-2-3 % accuracy on 1½” and 2”dial • 1.5 % accuracy on 2 ½”Dial (1% available by special request only) • 1% accuracy on 4” and 6”dial

Available Dial Sizes: • 1 ½”, 2”, 2 ½”, 4", 6"

Available Connection Sizes: • 1/8”MNPT on 1 1/2” and 2” • 1/4" MNPT on 2 1/2" and 4" • 1/2" MNPT on 4" and 6"

201L 1 1/2" 2" 2 1/2" 4" 6"

A 1.88”/48mm 2.24”/57mm 2.80”/71mm 4.32”/110mm 6.54”/166mm B 1.06”/27mm 1.27”/32mm 1.28”/33mm 1.63”/42mm 1.70”/43mm C .89”/23mm .71”/23mm 1.07”/27mm 1.25”/32mm 1.68”/43mm D 2.77”/58mm 2.80”/71mm 3.55”/90mm 5.57”/141mm 8.22”/210mm

E ⅛”NPT ⅛”or ¼” NPT ¼” NPT 1/4 or 1/2npt

202L 1 1/2" 2" 2 1/2" 3 ½” * 4" 6"

A 1.88”/48mm 2.23”/57mm 2.80”/71mm 3.82”/97mm 4.32”/110mm 6.54/166mm

B 1.06”/27mm 1.09”/28mm 1.28”/33mm 1.16”/29mm 1.63”/42mm 1.70”/43mm

C .89”/23mm .71”/23mm 1.18”/30mm 1.06”/27mm 1.14”/29mm 1.68”/43mm

D 1.95”/50mm 1.99”/51mm 2.46”/63mm 2.22”/56mm 2.77”/71mm 3.38”/86mm

E 1/8npt 1/8 or1/4npt 1/4mnpt 1/4mnpt

* 3 ½”Dial Size = Lower Back Mount Connection 203L

1 ½” 2" 2 ½” 3 ½” * 4" A 1.88”/48mm 2.23”/57mm 2.80”/71mm 3.82”/97mm 4.32”/110mm B 1.06”/27mm 1.09”/28mm 1.28”/33mm 1.16”/29mm 1.63”/42mm C .89”/23mm .71”/23mm 1.19”/30mm 1.06”/27mm 1.14”/29mm D 1.95”/50mm 1.99”/51mm 2.46”/63mm 2.22”/56mm 2.77”/71mm E 1/8npt 1/8 or 1/4npt 1/4mnpt 1/4mnpt 1/4mnpt F 2.63”/67mm 3.00”/76mm 3.49”/89mm 3.77”/96mm 5.30”/135mm G 1.63”/42mm 2.00”/51mm 2.50”/64mm 3.49”/88mm 3.87”/98mm

* 3 ½”Dial Size = Lower Back Mount Connection 204L

1 ½” 2" 2 ½” 3 ½” * 4" 6" A 1.88”/48mm 2.23”/57mm 2.80”/71mm 3.82”/97mm 4.32”/110mm 6.54”/166mm B 1.06”/27mm 1.09”/28mm 1.28”/33mm 1.16”/29mm 1.63”/42mm 1.70”/43mm C .89”/23mm .71”/23mm 1.18”/30mm 1.06”/27mm 1.14”/29mm 1.68”/43mm D 1.95”/50mm 1.99”/51mm 2.46”/63mm 2.22”/56mm 2.77”/71mm 3.38”/86mm E ⅛”NPT ⅛”or ¼” NPT ¼” NPT 1/4mnpt F 2.46”/63mm 2.81”/72mm 3.48”/88mm 5.19”/132mm 5.20”/132mm 7.78”/198mm G 1.63”/42mm 2.00”/51mm 2.50”/64mm 3.49”/88mm 3.87”/98mm 6.02”/153mm

* 3 ½”Dial Size = Lower Back Mount Connection

201L LIQUID FILLED

SPECIFICATIONS:

• Dial Sizes: 1 ½”, 2”, 2 ½”, 4", 6" • Connection Sizes: (with built-in snubber)

1/8”MNPT on 1 ½” and 2” 1/4"MNPT on 2”, 2 ½” and 4" 1/2"MNPT on 4" and 6"

• Stainless Steel Case And Bezel • Brass Internals and Connection (with built in snubber) • Phosphor Bronze Bourdon Tube • Plastic Lens • Liquid Filled (Dry Available) • Accuracy : 1 ½” or 2”Dial Size = 3-2-3 %

2 ½”Dial Size = 1.5 % 4” or 6”Dial Size = 1 %

• Dual Scale: PSI & Bar (x100=kPa) Single Scale available from stock

• Ambient temperature: FILLED: 30˚F to 160˚F DRY: -30˚F to 180˚F

RANGE CODE Major in Minor in 30/0"VAC A 5 0.5

30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1 0/100 E 20 2 0/160 F 20 2 0/200 G 40 4 0/300 H 50 5 0/400 I 50 5 0/500 J 100 10 0/600 K 100 10 0/800 L 100 10

0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/4000 Q 500 50 0/5000 R 1000 100 0/6000 S 2000 200

0/10,000 U 2000 200 0/15,000 V 2000 200

Som

e ra

nges

not

ava

ilabl

e in

all

dial

siz

es, p

leas

e ca

ll w

ith y

our p

artic

ular

app

licat

ion

A B C D E 1 ½” In 1.88 1.06 .89 2.77 1/8” Dial MM 48 27 23 58 NPT 2” In 2.24 1.27 .71 2.80 1/8” or

Dial MM 57 32 23 71 ¼” NPT 2 ½" In 2.80 1.28 1.07 3.55 1/4“ Dial MM 71 33 27 90 NPT 4" In 4.32 1.63 1.25 5.57 1/4" or

Dial MM 110 42 32 141 ½” NPT In 6.54 1.70 1.68 8.22 1/4“ or 6"

Dial MM 166 43 43 210 ½” NPT

Our ‘200’ series gauge line is a high quality line of liquid filled pressure gauges. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement and keeping contaminates such as dirt away from all moving parts, which will extend the life of the gauge. This gauge has been specifically designed with original equipment manufacturers in mind and is typically used on hydraulic and pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts where glycerine filling is suitable for use.

Our ‘200’ series gauge line is a high quality line of liquid filled pressure gauges. The glycerine filling and built in snubber helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement, keeping contaminates such as dirt away from all moving parts, which will extend the life of the gauge. This gauge has been specifically designed with the original equipment manufacturers in mind and is typically used on hydraulic & pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts where glycerine filling is suitable for use.

202L LIQUID FILLED

SPECIFICATIONS: • Dial Sizes: 1 ½”, 2”, 2 ½”, 3 ½”, 4" • Connection Sizes: (includes built-in snubber)

1/8”MNPT on 1 ½” and 2” 1/4"MNPT on 2”, 2 ½”, 3 ½” and 4"

• Stainless Steel Case And Bezel • Brass Internals & Connection • Phosphor Bronze Bourdon Tube • Plastic Lens Standard (Glass Available) • Liquid Filled (Dry Available) • Accuracy : 1 ½” and 2” Dial = 3-2-3 %

2 ½” Dial Size = 1.5 % 3 ½” and 4” Dial Size = 1 %



RANGE CODE Major In Minor inc.30/0"VAC A 5 0.5

30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 5 0/300 H 50 5 0/400 I 50 5 0/600 K 100 10 0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/5000 R 1000 100

0/10,000 U 1000 100 0/15,000 V 2000 200

A B C D E 1 ½” In 1.88 1.06 .89 1.95 1/8” Dial MM 48 27 23 50 NPT 2” In 2.23 1.09 .71 1.99 1/8” or

Dial MM 57 28 23 51 ¼”npt 2 ½" In 2.80 1.28 1.18 2.46 1/4“ Dial MM 71 33 30 63 NPT 3 ½” In 3.83 1.14 1.08 2.20 1/4“ Dial MM 97 29 27 56 NPT 4" In 4.32 1.63 1.14 2.77 1/4"

Dial MM 110 42 29 71 NPT

203L LIQUID FILLED

SPECIFICATIONS: • U-Clamp Panel Mount Design • Dial Sizes: 1 ½”, 2”, 2 ½”, 3 ½”, 4" • Connection Sizes:


• Stainless Steel Case And Bezel • Brass Internals & Connection (with built-in snubber) • Phosphor Bronze Bourdon Tube • Plastic Lens standard (Glass Available) • Liquid Filled (Dry Available) • Accuracy : 1 ½” or 2”Dial Size = 3-2-3 %

2 ½”Dial Size = 1.5 % 3 ½” or 4”Dial Size = 1 %



RANGE CODE Major In Minor inc. 30/0"VAC A 5 0.5

30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 5 0/300 H 50 5 0/400 I 50 5 0/600 K 100 10

0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/5000 R 1000 100

0/10,000 U 1000 100 0/15,000 V 2000 200

Our ‘200’ series gauge line is a high quality line of liquid filled pressure gauges. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement, keeping contaminates such as dirt away from all moving parts, which will extend the life of the gauge. This gauge has been specifically designed with the original equipment manufacturers in mind and is typically used on hydraulic & pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts where glycerine filling is suitable for use.

A B C D E F G 1 ½” In 1.88 1.06 .89 1.95 1/8” 2.63 1.63 Dial MM 48 27 23 50 Npt 67 42 2” In 2.23 1.09 .71 1.99 1/8” or 2.81 2.00

Dial MM 57 28 23 51 ¼”npt 72 51 2 ½" In 2.80 1.28 1.19 2.46 1/4“ 3.48 2.50 Dial MM 71 33 30 63 Npt 88 64 3 ½” In 3.83 1.14 1.08 2.20 1/4“ 3.70 3.5 Dial MM 97 29 27 56 Npt 94 89 4" In 4.32 1.63 1.14 2.77 1/4" 5.20 3.87

Dial MM 110 42 29 71 Npt 132 98

Note: All Dial Gauge S are Center Back Connection Except 3 ½” Dial Size which are Lower Back Connection

204L LIQUID FILLED

SPECIFICATIONS:

• Front Flanged Panel Mount Design • Dial Sizes: 1 ½”, 2”, 2 ½”, 3 ½”, 4" • Connection Sizes:


• Stainless Steel Case And Bezel • Brass Internals & Connection (with built-in snubber) • Phosphor Bronze Bourdon Tube • Plastic Lens • Liquid Filled (Dry Available) • Accuracy : 1 ½” or 2”Dial Size = 3-2-3 %

2 ½”Dial Size = 1.5 % 3 ½” or 4”Dial Size = 1 %



RANGE CODE Major In Minor inc. 30/0"VAC A 5 0.5

30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1 0/100 E 20 2 0/160 F 20 2 0/200 G 40 5 0/300 H 50 5 0/400 I 50 5 0/600 K 100 10

0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/5000 R 1000 100

0/10,000 U 1000 100 0/15,000 V 2000 200

Our ‘200’ series gauge line is a high quality line of liquid filled gauges. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement, keeping contaminates such as dirt away from all moving parts, which will extend the life of the gauge. This gauge has been specifically designed with the original equipment manufacturers in mind and is typically used on hydraulic & pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts where glycerine filling is suitable for use.

A B C D E F G 1 ½” In 1.88 1.06 .89 1.95 1/8” 2.46 1.63 Dial MM 48 27 23 50 Npt 63 42 2” In 2.23 1.09 .71 1.99 1/8” or 2.81 2.00

Dial MM 57 28 23 51 ¼”npt 72 51 2 ½" In 2.80 1.28 1.19 2.46 1/4“ 3.48 2.50 Dial MM 71 33 30 63 Npt 88 64 3 ½” In 3.83 1.14 1.08 2.20 1/4“ 5.19 3.5 Dial MM 97 29 27 56 Npt 132 89 4" In 4.32 1.63 1.14 2.77 1/8” or 5.20 3.87

Dial MM 110 42 29 71 ¼”Npt 132 98 Note: All Gauge sizes are Center Back Connection Except 3 ½” which are Lower

Back Connection

S215L BACK FLANGED

SPECIFICATIONS:

• Dial Sizes: 2 ½” or 4” • Connection Size: 1/4"MNPT • Stainless Steel Case And Bezel • Brass Internals and Connection (with built-in snubber) • Phosphor Bronze Bourdon Tube • Liquid Filled (Dry Available) • Accuracy : 2 ½”Dial Size = 1.5 %

4” Dial Size = 1 % • 2 ½”Dial Size Dual Scale: PSI & Bar (x100=kPa) • 4”Dial Size Single Scale: PSI Only • Ambient temperature: FILLED: 30˚F to 160˚F

DRY: -30˚F to 180˚F

A B C D E F 2 ½" In 3.41 2.8 1.33 3.54 ¼” 1.1 Dial MM 87 71 34 90 NPT 28 4" In 5.2 4.32 1.7 6.0 ¼” 1.48

Dial MM 132 110 43 152 NPT 38

RANGE CODE Major In Minor in 30/0"VAC A 5 0.5

30/0/30 CC 10 1 0/30 C 5 0.5 0/100 E 20 2 0/160 F 20 2

Our ‘S215L’ gauge is a heavy duty, high quality liquid filled gauge. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement, keeping contaminates such as dirt away from all moving parts, which will extend the life of the gauge. Rugged enough for the trucking industry, these heavy duty gauges are designed to withstand abuse and extremes that are well in excess of what is normally seen in almost any other commercial or industrial applications. These gauges therefore are suitable for use in any application where process media is not corrosive to brass and bronze wetted parts, where glycerine filling is favorable for use.

Notes: • Other Dial Sizes and Ranges are available. • Other Connections Sizes and Configurations. • Not all Dial Size / Range Combinations are in stock.

Please call to check stock

Part Numbers: S215x-xxx x Range Code (See Below) Connection 4 = ¼”NPT 2 = ½”NPT Dial Size 25 = 2 ½” 40 = 4” Fill D = Dry (No Fill) L = Glycerine Fill

211D DRY SS CASE GAUGES

SPECIFICATIONS:

• Dial Sizes: 2 ½” • Stainless Steel Case And Bezel • Connection Sizes: 1/4"MNPT (with built-in snubber) • Brass Internals & Connection • Phosphor Bronze Bourdon Tube • Glass Lens • Adjustable Pointer • Dry (Fillable) or Liquid Filled • Accuracy : 1.5 % Full Scale • Dual Scale: PSI & Bar (x100=kPa)

(Other dials available, call for details) • Ambient temperature: DRY: -30˚F to 180˚F

FILLED: 30˚F to 160˚F

Range Code Major in Minor in 30/0"VAC A 5 0.5

30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1 0/100 E 20 2 0/160 F 20 2 0/200 G 40 4 0/300 H 50 5 0/400 I 50 5 0/500 J 100 10 0/600 K 100 10 0/800 L 100 10

0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/4000 Q 500 50 0/5000 R 1000 100 0/6000 S 2000 200

0/10,000 U 2000 200 0/15,000 V 2000 200

Som

e ra

nges

not

ava

ilabl

e in

all

dial

siz

es, p

leas

e ca

ll w

ith y

our p

artic

ular

app

licat

ion

A B C D E F G In 2.73 1.35 1.07 3.55 .52 .83 2 ½"

Dial MM 70 34 27 90 1/4“ NPT 13 21

Our ‘200’ series gauge line is a high quality line of stainless steel case, brass internal pressure gauges. These gauges come complete with removable bezels, adjustable pointers, glass lens and 1.5% accuracy. This gauge is typically used on hydraulic and pneumatic systems as well as any commercial or industrial applications not corrosive to brass and bronze wetted parts. The removable bezel and adjustable pointer make minor adjustments a breeze – so that it possible to keep your gauge as accurate as it can be at all times.

212D ADJUSTABLE GAUGES SPECIFICATIONS:

• Available Dial Sizes: 2 ½” • Stainless Steel Case And Bezel • Available Connection Sizes: 1/4"MNPT • Brass Internals & Connection • Phosphor Bronze Bourdon Tube • Removable bezel • Glass Lens (Plastic Available) • Adjustable Pointer • Dry (Fillable) or Liquid Filled • Accuracy : 1.5 % Full Scale • Dual Scale: PSI & Bar (x100=kPa)

(Other dials available, call for details) • Ambient temperature: DRY: -30˚F to 180˚F

FILLED: 30˚F to 160˚F

RANGE CODE Major in Minor in 30/0"VAC A 5 0.5

30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1 0/100 E 20 2 0/160 F 20 2 0/200 G 40 4 0/300 H 50 5 0/400 I 50 5 0/500 J 100 10 0/600 K 100 10 0/800 L 100 10

0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/4000 Q 500 50 0/5000 R 1000 100 0/6000 S 2000 200

0/10,000 U 2000 200 0/15,000 V 2000 200 N

ote:

som

e ra

nges

not

ava

ilabl

e in

all

dial

siz

es, p

leas

e ca

ll w

ith y

our p

artic

ular

app

licat

ion

A B C D E F In 2.74 2.47 1.34 2.47 .55 2 ½"

Dial MM 70 63 34 63 1/4“ NPT 14

Our ‘210D’ series gauge line is a high quality line of stainless steel case, brass internal pressure gauges. These gauges come complete with removable bezels, adjustable pointers, glass lens and 1.5% accuracy. This gauge is typically used on hydraulic and pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts. The removable bezel and adjustable pointer allow re-zero or exact calibration at a specific point across the range of the gauge possible.

SEC-200 SERIES LIQUID FILLED

SPECIFICATIONS: Stainless steel case and bezel Brass internals and connection Liquid filled (dry available) Accuracy: 1 ½”, 2” & 2 ½”dial = 3-2-3 % 3 ½” dial = 1.5 % 4” & 6” dial = 1 %

AVAILABLE DIAL SIZES: 1 ½”, 2", 2 ½”, 3 ½”, 4" and 6" AVAILABLE CONNECTION SIZES: 1/8"MNPT on 1 1/2" and 2" 1/4"MNPT on 2" to 6" 1/2"MNPT on 4" and 6"

SEC-201L SEC-202L

1 1/2" 2" 2 1/2" 4" 6" A 1.88”/48mm 2.24”/57mm 2.80”/71mm 4.32”/110mm 6.54”/166mm

B 1.06”/27mm 1.27”/32mm 1.28”/33mm 1.63”/42mm 1.70”/43mm

C .89”/23mm .71”/23mm 1.07”/27mm 1.25”/32mm 1.68”/43mm

D 2.77”/58mm 2.80”/71mm 3.55”/90mm 5.57”/141mm 8.22”/210mm

E 1/8npt 1/8 or 1/4npt 1/4mnpt 1/4 or 1/2npt

1 1/2" 2" 2 1/2" 3 ½” * 4" 6" A 1.88”/48mm 2.23”/57mm 2.80”/71mm 3.82”/97mm 4.32”/110mm 6.54”/166mm

B 1.06”/27mm 1.09”/28mm 1.28”/33mm 1.16”/29mm 1.63”/42mm 1.70”/43mm

C .89”/23mm .71”/23mm 1.18”/30mm 1.06”/27mm 1.14”/29mm 1.68”/43mm

D 1.95”/50mm 1.99”/51mm 2.46”/63mm 2.22”/56mm 2.77”/71mm 3.38”/86mm

E 1/8npt 1/8 or1/4npt 1/4mnpt 1/4mnpt * 3 ½”Dial Size = Lower Back Mount Connection

1 ½” 2" 2 ½” 3 ½” * 4" 6" A 1.88”/48mm 2.23”/57mm 2.80”/71mm 3.82”/97mm 4.32”/110mm 6.54”/166mm

B 1.06”/27mm 1.09”/28mm 1.28”/33mm 1.16”/29mm 1.63”/42mm 1.70”/43mm

C .89”/23mm .71”/23mm 1.18”/30mm 1.06”/27mm 1.14”/29mm 1.68”/43mm

D 1.95”/50mm 1.99”/51mm 2.46”/63mm 2.22”/56mm 2.77”/71mm 3.38”/86mm

E 1/8npt 1/8 or 1/4npt 1/4mnpt 1/4mnpt

F 2.46”/63mm 2.81”/72mm 3.48”/88mm 5.19”/132mm 5.20”/132mm 7.78”/198mm

G 1.63”/42mm 2.00”/51mm 2.50”/64mm 3.49”/88mm 3.87”/98mm 6.02”/153mm * 3 ½”Dial Size = Lower Back Mount Connection

1 ½” 2" 2 ½” 3 ½” * 4" A 1.88”/48mm 2.23”/57mm 2.80”/71mm 3.82”/97mm 4.32”/110mm

B 1.06”/27mm 1.09”/28mm 1.28”/33mm 1.16”/29mm 1.63”/42mm

C .89”/23mm .71”/23mm 1.19”/30mm 1.06”/27mm 1.14”/29mm

D 1.95”/50mm 1.99”/51mm 2.46”/63mm 2.22”/56mm 2.77”/71mm

E 1/8npt 1/8 or 1/4npt 1/4mnpt 1/4mnpt 1/4mnpt

F 2.63”/67mm 3.00”/76mm 3.49”/89mm 3.77”/96mm 5.30”/135mm

G 1.63”/42mm 2.00”/51mm 2.50”/64mm 3.49”/88mm 3.87”/98mm * 3 ½”Dial Size = Lower Back Mount Connection

SEC-203L

SEC-204L

SEC-201L LIQUID FILLED

SPECIFICATIONS:

• Dial Sizes: 2 ½” • Connection Sizes: 1/4"NPT • Stainless Steel Case And Bezel • Brass Internals & Connection (with built-in snubber) • Phosphor Bronze Bourdon Tube • Plastic Lens • Liquid Filled • Accuracy : 3-2-3 % • Dual Scale: PSI & Bar (x100=kPa) • Ambient temperature: 30˚F to 160˚F


30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 5 0/300 H 50 5 0/400 I 50 5 0/600 K 100 10 0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/5000 R 1000 100

0/10,000 U 1000 100 0/15,000 V 2000 200

A B C D E 2 ½" In 2.80 1.28 1.07 3.55 1/4“ Dial MM 71 33 27 90 NPT

*Dimensions subject to change

Our ‘SEC-200L’ series gauge line is a quality line of liquid filled pressure gauges. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement (and keeping contaminates such as dirt away from all moving parts) which will extend the life of the gauge. This gauge has been specifically designed with original equipment manufacturers in mind. It is typically used on hydraulic & pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts where glycerine filling is suitable for use.

Our ‘SEC-202L’ gauge is a quality line of glycerine liquid filled pressure gauges. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement (and keeping contaminates such as dirt away from all moving parts) which will extend the life of the gauge. This gauge has been specifically designed with original equipment manufacturers in mind. It is typically used on hydraulic and pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts where glycerine filling is suitable for use.


SPECIFICATIONS: • Dial Size: 2 ½” • Connection Size: 1/4"MNPT • Stainless Steel Case And Bezel • Brass Internals & Connection (with built-in snubber) • Phosphor Bronze Bourdon Tube • Plastic Lens Standard (Glass Available) • Liquid Filled (Dry Available) • Accuracy : 3-2-3 % • Dual Scale: PSI & Bar (x100=kPa)

Single Scale available • Ambient temperature: FILLED: 30˚F to 160˚F

DRY: -30˚F to 180˚F


30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 5 0/300 H 50 5 0/400 I 50 5 0/600 K 100 10 0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/5000 R 1000 100

0/10,000 U 1000 100 0/15,000 V 2000 200

A B C D E In 2.73 1.30 1.13 2.44 2 ½"

Dial MM 69.5 33 28.5 62 1/4“ NPT

In 4.17 1.54 1.26 2.80 4” Dial MM 106 39 32 71

¼” or ½” NPT



SPECIFICATIONS: • U-Clamp Panel Mount Design • Dial Size: 2 ½” • Connection Size: 1/4"MNPT • Stainless Steel Case And Bezel • Brass Internals & Connection (with built-in snubber) • Phosphor Bronze Bourdon Tube • Liquid Filled (Dry Available) • Accuracy : 3-2-3 % • Dual Scale: PSI & Bar (x100=kPa)

Single Scale available from stock • Ambient temperature: FILLED: 30˚F to 160˚F

DRY: -30˚F to 180˚F


30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 5 0/300 H 50 5 0/400 I 50 5 0/600 K 100 10 0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/5000 R 1000 100

0/10,000 U 1000 100 0/15,000 V 2000 200

Our ‘SEC-200’ series gauge line is a high quality line of liquid filled pressure gauges. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement (and keeping contaminates such as dirt away from all moving parts) which will extend the life of the gauge. This gauge has been specifically designed with original equipment manufacturers in mind and is typically used on hydraulic and pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts where glycerine filling is suitable for use.

A B C D E F G 2 ½" In 2.80 1.28 1.19 2.46 1/4“ 3.48 2.50 Dial MM 71 33 30 63 NPT 88 64

Our ‘SEC-204L’ gauge is a quality line of panel mount glycerine liquid filled pressure gauges. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement, keeping contaminates such as dirt away from all moving parts, which will extend the life of the gauge. This gauge has been specifically designed with original equipment manufacturers in mind. It is typically used on hydraulic and pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts where glycerine filling is suitable for use.


SPECIFICATIONS: • Dial Size: 2 ½” • Connection Size: 1/4"MNPT • Stainless Steel Case And Bezel • Brass Internals & Connection (includes built-in snubber) • Phosphor Bronze Bourdon Tube • Plastic Lens Standard (Glass Available) • Liquid Filled (Dry Available) • Accuracy : 3-2-3 % • Dual Scale: PSI & Bar (x100=kPa)

Single Scale available • Ambient temperature: FILLED: 30˚F to 160˚F

DRY: -30˚F to 180˚F


30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 5 0/300 H 50 5 0/400 I 50 5 0/600 K 100 10 0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/5000 R 1000 100

0/10,000 U 1000 100 0/15,000 V 2000 200

A B C D E F In 2.73 1.30 1.13 2.44 3.452 ½"

Dial MM 69.5 33 28.5 62 1/4“ NPT 88

In 4.17 1.54 1.26 2.80 5.154” Dial MM 106 39 32 71

¼” or ½” NPT 131

* Dimensions subject to change

SE-201LFW-EZ E-Z READ DIAL

SPECIFICATIONS: • Available Dial Sizes: 2 ½” • Available Connection Sizes: 1/4"NPT • Stainless Steel Case And Bezel • Brass Internals & Connection • Phosphor Bronze Bourdon Tube • Liquid Filled • Accuracy : Standard = 3-2-3 % Per ANSI grade B • Dual Scale: PSI & Bar (x100=kPa) • Ambient temperature: 30˚F to 160˚F

A B C D E 2 ½" In 2.80 1.28 1.07 3.55 1/4“ Dial MM 71 33 27 90 NPT


Range Code Major Minor 30/0"VAC A 5 0.5

30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 5 0/300 H 50 5 0/400 I 50 5 0/600 K 100 10

0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/5000 R 1000 100

0/10,000 U 1000 100 0/15,000 V 2000 200

Our ‘SE-200LFW-EZ’ series gauge line is a quality line of liquid filled pressure gauges. The ‘EZ-read’ dial allows accurate and easy readings from a convenient distance. This is also beneficial for safety if there is a chance that the gauge may be over-pressured – keeping inspectors out of harms way.

The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement (and keeping contaminates such as dirt away from all moving parts) which will extend the life of the gauge. This gauge has been specifically designed with original equipment manufacturers in mind. It is typically used on hydraulic & pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts where glycerine filling is suitable for use.

Notice how the ‘EZ-READ’ Dial allows clear, accurate and easy readings from a convenient

distance. This is also beneficial for safety if there is a chance that the gauge may be over-

pressured, keeping inspectors out of harms way.

S201L SINGLE SCALE

SPECIFICATIONS:

• Dial Sizes: 2 ½” or 4" • Connection Sizes: 1/4" or 1/2"MNPT • Stainless Steel Case And Bezel • Bronze Tube & Brass Connection • Plastic Lens • Built in Snubber (for extra dampening effect) • Liquid Filled (Dry Available) • Accuracy : 1 % Full Scale • Single Scale: PSI Only

(Dual Scale available) • Ambient temperature: FILLED: 30˚F to 160˚F

DRY: -30˚F to 180˚F

RANGE CODE Major In Minor inc.0/30 C 5 0.5 0/60 D 10 1

0/100 E 10 1 0/160 F 20 2 0/200 G 20 2 0/300 H 50 5 0/600 K 100 10

0/1000 M 100 10 0/1500 N 300 20 0/2000 O 200 20 0/3000 P 500 50 0/5000 R 500 50

0/10,000 U 1000 100 0/15,000 V 3000 200

Other Ranges Available, Please call with all of your inquiries A B C D E

4" In 4.29” 1.68” 1.42” 5.56” 1/4" or Dial MM 109 43 36 141 ½”npt

Our ‘S201L’ series gauge line is a quality line of industrial liquid filled pressure gauges for the oil and gas market. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement, keeping contaminates such as dirt away from all moving parts which will extend the life of the gauge.

This gauge has been specifically designed with the oil & gas OEMs, contractors and drillers in mind and are typically used on well head assemblies (both on and off shore) as well as hydraulic and pneumatic systems in any commercial or industrial application where glycerine filling is suitable for use.

Available Accessories Include:

Diaphragm Seals Needle Valve & Gauge Valves Snubbers, Siphons & Accessories

300LFW SERIES ALL SS GAUGES

SPECIFICATIONS:

• Stainless steel case and bezel • 316SS internals and connection • Connection welded to case • Liquid filled (dry available) • 3-2-3 % accuracy on 1½” & 2”dial • 1.6 % accuracy on 2 ½”dial • 1% accuracy on 4” & 6”dial

(1% accuracy available on 2½”dial by special request only – consult factory)

AVAILABLE DIAL SIZES: • 1 ½”, 2”, 2 ½”, 4", 6"

AVAILABLE CONNECTION SIZES: • 1/4"MNPT on 2 1/2" and 4" • 1/2"MNPT on 4" and 6"

301LFW

2 1/2" 4" 6" A 2.8" 4.35" 6.5" B 1.23" 1.28" 1.7" C 1" 1.475" 1.41” D 3.63" 5.75" 3.05” E .5" .8" ¼” or ½”

302LFW (4”Dial Size = Lower Back Connected & Removable Bezel)

1 1/2" 2 1/2" 4” A 1.7" 2.8" 4.37” B 1.1" 1.23" 1.71” C .875" 1.1" 1.41” D 2" 2.35" 3.05” E .55" .5" ¼” or ½”

303LFW

1 1/2" 2 1/2" 4” A 1.73" 2.8" B 1.05" 1.23" C .825" 1.1" D 1.8" 2.38" E .375" .5" F G 1.56" 2.45"

304LFW (4”Dial Size = Lower Back Connected & Removable Bezel)

1 1/2" 2 1/2" 4” A 1.73" 2.8" 4.37” B 1.05" 1.23" 1.71” C .825" 1.1" 1.41” D 1.8" 2.38" 3.05” E .375" .5" ¼” or ½” F 2.46” 3.43" 5.22” G 1.56" 2.45" 3.90”

301LFW ALL SS LOWER MOUNT

SPECIFICATIONS:

• Available Dial Sizes: 2 ½”, 4", 6" • Available Connection Sizes:

1/4"MNPT on 2”, 2 ½” and 4" 1/2"MNPT on 4" and 6"

• Stainless Steel Case, Crimped Bezel • 316 SS Bourdon Tube , SS Internals • 316 SS Connection Welded at Case • Built-in Snubber • Plastic Lens • Liquid Filled (Dry Available) • Accuracy : 2 ½”Dial Size = 1.5 %

4” and 6” Dial Size = 1 % • Dual Scale: PSI & Bar (x100=kPa)

(Single Scale available) • Ambient temperature: FILLED: 30˚F to 160˚F

DRY: -30˚F to 180˚F


30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 4 0/300 H 50 5 0/400 I 50 5 0/500 J 100 10 0/600 K 100 10 0/800 L 100 10

0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/4000 Q 500 50 0/5000 R 1000 100 0/6000 S 2000 200

0/10,000 U 2000 200 0/15,000 V 2000 200

A B C D E 2 ½" In 2.67 1.30 1.04 3.50 1/4“ Dial MM 68 33 26 89 NPT 4" In 4.32 1.63 1.25 5.57 1/4" or

Dial MM 110 42 32 141 ½”npt In 6.54 1.70 1.68 8.22 6"

Dial MM 166 43 43 210 1/4“ or ½”npt

Our ‘300’ series pressure gauge line is a high quality line of liquid filled gauges. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement and keeping contaminates such as dirt away from all moving parts, which will extend the life of the gauge. This gauge has been specifically designed with original equipment manufacturers in mind. It is typically used in chemical processing or food processing applications as well as any commercial or industrial application where stainless steel components are required.

302LFW ALL SS BACK MOUNT

SPECIFICATIONS:

• Available Dial Sizes: 1 ½”, 2”, 2 ½”, 3 ½”, 4" • Available Connection Sizes:


• Stainless Steel Case, Crimped Bezel • 316SS Bourdon Tube, SS Internals • 316SS Connection Welded at Case • Built-in Snubber • Plastic Lens • Liquid Filled (Dry Available) • Accuracy : 2 ½”Dial = 1.5 %

4” and 6” Dial = 1 % • Dual Scale: PSI & Bar (x100=kPa)


DRY: -30˚F to 180˚F


30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 5 0/300 H 50 5 0/400 I 50 5 0/600 K 100 10 0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/5000 R 1000 100

0/10,000 U 1000 100 0/15,000 V 2000 200

Our ‘300’ series pressure gauge line is a high quality line of stainless steel gauges. Glycerine filling the gauge prevents dust, dirt or other contaminates from entering the case of the gauge and attacking the movement or internals of the gauge. Keeping out such contaminates prolongs the life of the gauge. This gauge has been specifically designed with original equipment manufacturers in mind. It is typically used in chemical processing or food processing applications as well as any commercial or industrial application where stainless steel components are required.

A B C D E In 1.88 1.06 .89 1.95 1 ½”

Dial MM 48 27 23 50 1/8” NPT

In 2.23 1.09 .71 1.99 2” Dial MM 57 28 23 51

1/8” OR ¼”NPT

In 2.80 1.28 1.19 2.46 2 ½" Dial MM 71 33 30 63

1/4“ NPT

In 3.83 1.14 1.08 2.20 3 ½” Dial MM 97 29 27 56

1/4“ NPT

In 4.32 1.63 1.14 2.77 4" Dial MM 110 42 29 71

1/4" NPT

Note: All Dial Size Gauges are Center Back Connection Except 3 ½” Dial Size which are Lower Back Connection

303LFW ALL SS PANEL MOUNT

SPECIFICATIONS:

• U-Clamp Panel Mount Design • Dial Sizes: 2 ½” • Connection Sizes: 1/4"MNPT • Stainless Steel Case, Crimped Bezel • 316SS Bourdon Tube, SS Internals • 316SS Connection Welded at Case • Built-in snubber • Plastic Lens • Liquid Filled (Dry Available) • Accuracy : 1.5 %

(Special Accuracy Available Upon Request) • Dual Scale: PSI & Bar (x100=kPa) • Ambient temperature: FILLED: 30˚F to 160˚F

DRY: -30˚F to 180˚F


30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 5 0/300 H 50 5 0/400 I 50 5 0/600 K 100 10

0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/5000 R 1000 100

0/10,000 U 1000 100 0/15,000 V 2000 200


A B C D E F G 2 ½" In 2.70 1.38 1.09 2.50 3.79 2.44

Dial MM 68.75 35 27.75 63.49 1/4" NPT 96.28 62

304LFW ALL SS PANEL MOUNT

SPECIFICATIONS:

• Front Flanged Panel Mount Design • Dial Sizes: 2 ½” • Connection Sizes: 1/4"MNPT • Stainless Steel Case, Crimped Bezel • 316SS Bourdon Tube, SS Internals • 316SS Connection Welded at Case • Built-in Snubber • Plastic Lens • Liquid Filled (Dry Available) • Accuracy : 1.5 %


DRY: -30˚F to 180˚F


30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 5 0/300 H 50 5 0/400 I 50 5 0/600 K 100 10 0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/5000 R 1000 100

0/10,000 U 1000 100 0/15,000 V 2000 200


A B C D E F G 2 ½" In 2.80 1.28 1.19 2.46 3.48 2.50 Dial MM 71 33 30 63

1/4" NPT 88 64

311D ALL SS BOTTOM MOUNT

SPECIFICATIONS: • Dial Size: 2 ½” • Connection Size: 1/4"MNPT • Stainless Steel Case, Removable Bezel • 316SS Bourdon Tube, SS Internals • 316SS Connection Welded at Case • Built-in Snubber • Laminated Safety Glass Lens • Hermetically sealed (Liquid Fillable) • Accuracy : 1 % Full Scale • Single Scale PSI Only (Dual Scale Available by Request) • Temperature: -40 to 190˚F *

*(Note: Temperature can affect Accuracy & Lifespan)

RANGE CODE Major In Minor in 30/0"VAC A 5 0.5 30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/160 CF 20 2 30/0/300 CH 50 10

0/15 B 3 0.25 0/30 C 5 0.5 0/60 D 10 1

0/100 E 10 1 0/160 F 20 2 0/200 G 20 2 0/300 H 30 5 0/400 I 50 5 0/600 K 100 10 0/800 L 100 10

0/1000 M 100 10 0/1500 N 300 25 0/2000 O 200 20 0/3000 P 500 50 0/5000 R 500 50 0/6000 S 1000 100

0/10,000 U 1000 100 0/15,000 V 3000 250

Our '311D' series pressure gauge line is designed for process applications where 1 % accuracy and calibration via an adjustable pointer are desired to monitor important pressures accurately. This gauge has been specifically designed with higher-end process applications in mind and are used on any process systems as well as any commercial or industrial application where stainless steel wetted parts are needed. These gauges also have laminated safety glass lens required where chemical wash downs are common and/or safety requirements demand shatter proof glass lens.

A B C D E F G

Inches 2.75” 1.3” .94” 3.5” .5” 8” MM 70 33 24 89

1/4“ NPT 13 20

314D ALL SS PANEL MOUNT

SPECIFICATIONS:

• Front Flange Panel Mount Design • Dial Sizes: 2 ½” or 4" • Connection Sizes:1/4"MNPT (1/2” Available) • Stainless Steel Case, Removable Bezel • 316SS Bourdon Tube, SS Internals • 316SS Connection Welded at Case • Built-in Snubber • Laminated Safety Glass Lens • Dry but Fillable • Accuracy : 2 ½”Dial = 1.5 % Full Scale

4”Dial = 1 % Full Scale • Single Scale: PSI (Dual Scale available) • Ambient temperature: FILLED: 30˚F to 160˚F

DRY: -30˚F to 180˚F


30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 10 1 0/160 F 20 2 0/200 G 20 2 0/300 H 30 5 0/400 I 50 5 0/600 K 100 10

0/1000 M 200 20 0/1500 N 300 25 0/2000 O 200 20 0/3000 P 500 50 0/5000 R 500 50

0/10,000 U 1000 100 0/15,000 V 3000 250

Our '314D' series pressure gauge line is designed for process applications where 1 % accuracy and calibration via an adjustable pointer are desired to monitor important pressures accurately. This gauge has been specifically designed with higher-end process applications in mind and are used on any process systems as well as any commercial or industrial application where stainless steel wetted parts are needed. These gauges also have laminated safety glass lens required where chemical wash downs are common and/or safety requirements demand shatter proof glass lens.

A B C D E F H In 2.71 1.23 1.00 2.23 3.45 2.45 2 ½”

Dial MM 68.8 31.3 25.4 56.7 1/4" NPT 87.6 62.2

4" In 4.36 1.73 1.34 3.07 5.22 3.84 Dial MM 111 44 34 78

1/4" NPT 132 97

S301L ALL SS BOTTOM MOUNT

SPECIFICATIONS: • Dial Sizes: 4" • Connection Sizes: 1/2"MNPT • Stainless Steel Case, Crimped Bezel • 316 SS Bourdon Tube, SS Internals • 316SS Connection Welded at Case • Built in Snubber • Plastic Lens • Liquid Filled (Dry Available) • Accuracy : 1 % Full Scale • Single Scale: PSI Only

(Dual Scale available) • Ambient temperature: FILLED: 30˚F to 160˚F

DRY: -30˚F to 180˚F

RANGE CODE Major In Minor in 0/30 C 5 0.5 0/60 D 10 1

0/100 E 10 1 0/160 F 20 2 0/200 G 20 2 0/300 H 50 5 0/600 K 100 10

0/1000 M 100 10 0/1500 N 300 20 0/2000 O 200 20 0/3000 P 500 50 0/5000 R 500 50

0/10,000 U 1000 100 0/15,000 V 3000 200

Other Ranges Available, Please call with all of your inquiries

A B C D E 4" In 4.29” 1.68” 1.42” 5.56” 1/4" or

Dial MM 109 43 36 141 ½”npt

Our ‘S301L’ series pressure gauge line is a quality line of industrial liquid filled gauges with single scale dial and stainless steel wetted parts. This gauge has been designed with oil and gas OEMs, contractors and drillers in mind. They are typically used on well head assemblies (both on-shore and off-shore) as well as hydraulic & pneumatic systems in any commercial or industrial application where glycerine filling is suitable for use. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement and keeps contaminates such as dirt away from all moving parts, which will extend the life of the gauge.



SEC-301LFW SS BOTTOM MOUNT

SPECIFICATIONS: • Dial Size: 2 ½” • Connection Size: 1/4"MNPT • Stainless Steel Case, Crimped bezel • 316SS Bourdon Tube, SS Internals • 316SS Connection Welded at Case • Built in Snubber • Plastic Lens • Liquid Filled (Dry Available) • Accuracy : 1.5 % • Dual Scale: PSI & Bar (x100=kPa) • Ambient temperature: FILLED: 30˚F to 160˚F

DRY: -30˚F to 180˚F

RANGE CODE Major In minor in 30/0"VAC A 5 0.5

30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 4 0/300 H 50 5 0/400 I 50 5 0/500 J 100 10 0/600 K 100 10 0/800 L 100 10

0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/4000 Q 500 50 0/5000 R 1000 100 0/6000 S 2000 200

0/10,000 U 2000 200 0/15,000 V 2000 200

A B C D E 2 ½" In 2.80 1.28 1.07 3.55 1/4“ Dial MM 71 33 27 90 Npt

Our ‘SEC-300’ series pressure gauge line is a high quality line of liquid filled gauges. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement and keeping contaminates such as dirt away from all moving parts, which will extend the life of the gauge. This gauge line has been specifically designed with the original equipment manufacturers in mind and is typically used on hydraulic & pneumatic systems as well as any commercial or industrial application not corrosive to 316ss wetted parts where glycerine filling is suitable for use.

4001 HEAVY DUTY 4” ALL SS

SPECIFICATIONS: • DIAL: 4” Diameter • CONNECTION: 1/4” or ½”NPT • CASE: Stainless Steel, Removable Bezel • BOURDON TUBE: 316 Stainless Steel • SOCKET :316 Stainless Steel Welded to Case • LENS: Laminated Safety Glass • POINTER: Adjustable • MOVEMENT: SS Heavy Duty Bushed

• w/ Overload – Underload stops • ACCURACY: 0.5% Full Scale

A B C D E F G H I (=NPT) INCH 4.02 1.93 3.87 .70 .74 .66 1.38 .68 ½” or MM 102 49 98.5 18 19 17 35 17 ¼”

STANDARD FEATURES *Hermetically Sealed/Weather Proof *Welded Case and Connection *Liquid Fillable / No Kit Required

RANGE FIGURES MINOR 30”-0 hg vac 5” 0.2” 30”-0-15 10” & 5 psi 1” & 0.5 psi 30”-0-30 10” & 5 psi 1” & 0.5 psi 30”-0-60 10” & 10 psi 2” & 1 psi 30”-0-100 10” & 20 psi 2” & 1 psi 30”-0-150 10” & 30 psi 5” & 2 psi 30”-0-200 10” & 50 psi 5” & 2 psi 30”-0-300 10” & 50 psi 10” & 5 psi 30”-0-600 10” & 100 10” & 10 0-15 psi 3 psi 0.2 psi 0-30 psi 5 psi 0.2 psi 0-60 psi 5 psi 0.5 psi

0-100 psi 10 psi 1 psi 0-160 psi 20 psi 1 psi 0-200 psi 20 psi 2 psi 0-300 psi 50 psi 2 psi 0-400 psi 50 psi 2 psi 0-600 psi 50 psi 5 psi 0-800 psi 100 psi 5 psi 0-1000 psi 100 psi 10 psi 0-1500 psi 250 psi 10 psi 0-2000 psi 200 psi 20 psi 0-3000 psi 500 psi 20 psi 0-5000 psi 1,000 psi 50 psi

0-10,000 psi 1,000 psi 100 psi 0-15,000 psi 2,500 psi 100 psi 0-20,000 psi 2,000 psi 200 psi

4501 PROCESS GAUGE

STANDARD SPECIFICATIONS: • DIAL: 4 ½” Diameter • CONNECTION: ¼” or ½”NPT Bottom Connect • CASE: Phenolic–Solid Front/Blow-Out Back • LENS: Plastic Shatterproof (Safety Glass Avail) • POINTER: Micro-Adjustable • BOURDON TUBE: 316L Stainless Steel • SOCKET : 316L Stainless Steel • MOVEMENT: Heavy Duty 304 SS • ACCURACY: 0.5 % Full Scale

STANDARD FEATURES • Overload and Underload Stops • Hermetically Sealed / Weather Proof • Liquid Fillable / No Kit Required

RANGE FIGURES MINOR 30”-0 hg vac 5” 0.2”

30”-0-15 10” & 5 psi 1” & 0.5 psi 30”-0-30 10” & 5 psi 1” & 0.5 psi 30”-0-60 10” & 10 psi 2” & 1 psi 30”-0-100 10” & 20 psi 2” & 1 psi 30”-0-150 10” & 30 psi 5” & 2 psi 30”-0-200 10” & 50 psi 5” & 2 psi 30”-0-300 10” & 50 psi 10” & 5 psi 30”-0-600 10” & 100 psi 10” & 10 psi 0-15 psi 3 psi 0.2 psi 0-30 psi 5 psi 0.2 psi 0-60 psi 5 psi 0.5 psi



A B C D E F G NPT INCH 5.07 5.91 3.03 .91 1.38 2.56 1.38 MM 129 150 77 23 35 65 35

½” or ¼”

Ranges and Dimensions:

4502 BACK CONNECT PROCESS

STANDARD SPECIFICATIONS: • DIAL: 4 ½” Diameter • CONNECTION: ¼” or ½”NPT Bottom Connect • CASE: Phenolic–Solid Front/Blow-Out Back • LENS: Plastic • POINTER: Micro-Adjustable • BOURDON TUBE: 316 Stainless Steel • SOCKET : 316 Stainless Steel • MOVEMENT: 304SS Heavy Duty Bushed • ACCURACY: 0.5 % Full Scale

STANDARD FEATURES

• Overload and Underload Stops • Hermetically Sealed / Weather Proof • Liquid Fillable / No Kit Required

A B C D F G NPT INCH 5.08 5.84 3.44 1.10 2.54 4.27 ½” or MM 129 148 87 28 65 108 ¼”

RANGE FIGURES MINOR 30”-0 hg vac 5” 0.2” 30”-0-15 10” & 5 psi 1” & 0.5 psi 30”-0-30 10” & 5 psi 1” & 0.5 psi 30”-0-60 10” & 10 psi 2” & 1 psi 30”-0-100 10” & 20 psi 2” & 1 psi 30”-0-150 10” & 30 psi 5” & 2 psi 30”-0-200 10” & 50 psi 5” & 2 psi 30”-0-300 10” & 50 psi 10” & 5 psi 30”-0-600 10” & 100 psi 10” & 10 psi 0-15 psi 3 psi 0.2 psi 0-30 psi 5 psi 0.2 psi 0-60 psi 5 psi 0.5 psi



4504 / 6504 PANEL MOUNT

Our 4504 and 6504 are Process grade Front Flange Panel Mount Gauges. These gauges are designed for precision and safety with an solid front, Blow-out back Safety Case. There is a solid wall between the pressure sensing unit and the window, which provides greater safety for personnel monitoring the gauges.

The Hinged front allows users to remove the front cover with a simple thumb screw for easy panel installation and re-calibration when necessary. 0.5 % Accuracy and Stainless Steel wetted parts make this gauge an excellent choice for industrial and process applications where accuracy and durability are required.

These gauges are supplied as dry only and available in 4 ½” or 6”Dial Size.

STANDARD SPECIFICATIONS: DIAL: 4 ½” or 6” CONNECTION: ¼” or ½”NPT CASE: Front Flanged Aluminum Safety Case LENS: Plastic for 4 ½”Dial Size Glass for 6”Dial Size DIAL: Single Scale PSI only (Dual Scale available by request) POINTER: Micro-Adjustable BOURDON TUBE: 316 Stainless Steel SOCKET: 316 Stainless Steel MOVEMENT: Heavy Duty 304 SS ACCURACY: 0.5 % Full Scale

Dimensions

Dial Size A B C D E F G H I

4504 4 ½” (115mm)

6.17” (157)

4.78” (122)

1.78” (45)

.58” (15)

1.675” (43)

4.65” (118)

2.375” (60)

4.02” (102)

1.26” (32)

6504 6” (150mm)

4501-SC SS CASE PROCESS

STANDARD SPECIFICATIONS: • DIAL: 4 ½” Diameter • CASE: Stainless Steel

Solid Front/Blow-Out Back • CONNECTION: ¼” or ½”NPT • LENS: Plastic • POINTER: Micro-Adjustable • BOURDON TUBE: 316 Stainless Steel • SOCKET : 316 Stainless Steel • MOVEMENT: Heavy Duty Bushed • ACCURACY: 0.5 % Full Scale

STANDARD FEATURES

• Overload and Underload Stops • Hermetically Sealed / Weather Proof • Welded Case and Connection • Liquid Fillable / No Kit Required

A B C D E F G H I (=NPT)INCH 5.42” 1.62” 4.75” 1.10” .81” .61” 1.50” .75” ½” or MM 138 41 120 28 20 15.5 38 19 ¼”

RANGE FIGURES MINOR 30”-0 hg vac 5” 0.2” 30”-0-15 10” & 5 psi 1” & 0.5 psi 30”-0-30 10” & 5 psi 1” & 0.5 psi 30”-0-60 10” & 10 psi 2” & 1 psi 30”-0-100 10” & 20 psi 2” & 1 psi 30”-0-150 10” & 30 psi 5” & 2 psi 30”-0-200 10” & 50 psi 5” & 2 psi 30”-0-300 10” & 50 psi 10” & 5 psi 30”-0-600 10” & 100 psi 10” & 10 psi 0-15 psi 3 psi 0.2 psi 0-30 psi 5 psi 0.2 psi 0-60 psi 5 psi 0.5 psi



6001 6” DIAL ALL STAINLESS

STANDARD SPECIFICATIONS: DIAL: 6” Diameter CASE: Stainless Steel LENS: Laminated Safety Glass POINTER: Micro Adjustable BOURDON TUBE: 316 Stainless Steel SOCKET : 316 Stainless Steel MOVEMENT: SS Heavy Duty ACCURACY: 1 % Full Scale

STANDARD FEATURES *Hermetically Sealed / Weather Proof *Welded Case and Connection *Liquid Fillable / No Kit Required

A B C D E F G Conn. INCH 6.75” 2.00” 1.50” 8.41” .54” .73” 1.27” MM 172 50 38 214 14 18 32

¼” or ½”NPT

RANGE FIGURES MINOR 30”-0 hg vac 5” 0.2”

30”-0-15 10” & 5 psi 1” & 0.5 psi 30”-0-30 10” & 5 psi 1” & 0.5 psi 30”-0-60 10” & 10 psi 2” & 1 psi 30”-0-100 10” & 20 psi 2” & 1 psi 30”-0-150 10” & 30 psi 5” & 2 psi 30”-0-200 10” & 50 psi 5” & 2 psi 30”-0-300 10” & 50 psi 10” & 5 psi 30”-0-600 10” & 100 psi 10” & 10 psi 0-15 psi 3 psi 0.2 psi 0-30 psi 5 psi 0.2 psi 0-60 psi 5 psi 0.5 psi



601L CAST BRASS LIQUID FILLED

SPECIFICATIONS:

• Available Dial Sizes: 2 ½” or 4” • Connection Sizes:1/4" or 1/2"NPT • Forged Brass Case • Brass Internals & Connection • Phosphour Bronze Bourdon Tube • Liquid Filled (Dry Available) • Accuracy : 2 ½”= 1.5 %, 4”=1% • Single Scale: PSI • Ambient temperature: FILLED: 30˚F to 160˚F

DRY: -30˚F to 180˚F

A B C D E In 2.57 1.44 .81 3.41 2 ½"

Dial MM 65 36.5 20.5 87 1/4“ NPT

In 4.05 2.02 1.46 5.47 4” Dial MM 103 51.5 37 139

1/4“ or 1/2"


0/15 B 2 0.1 0/30 C 3 0.2 0/60 D 5 0.5

0/100 E 10 1 0/160 F 20 2 0/200 G 20 2 0/300 H 30 2 0/400 I 50 5 0/600 K 50 5

0/1000 M 100 10 0/1500 N 200 10 0/2000 O 200 20 0/3000 P 500 20 0/5000 R 500 50 0/7500 T 500 50

0/10,000 U 1000 100

Our ‘600’ series gauge line is a high quality line of forged brass case liquid filled gauges. The sturdy brass case adds extra protection along with the glycerine filling which helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement (and keeping contaminates such as dirt away from all moving parts) which will extend the life of the gauge. this gauge has been specifically designed with heavy industrial applications in mind where rugged designed gauges are required as well as any commercial or industrial application not corrosive to brass and bronze wetted parts and where glycerine filling is suitable for use.

701L POLY-CASE LIQUID FILLED

SPECIFICATIONS:

• Dial Sizes: 2 ½” • Connection Sizes: 1/4"MNPT • Plastic Case And Bezel • Brass Internals & Connection • Phosphour Bronze Bourdon Tube • Liquid Filled (Dry Available) • Accuracy : 1.5 % Full Scale • Dual Scale: PSI & Bar (x100=kPa)


RANGE CODE Major in Minor in 30/0"VAC A 5 0.5 30/0/15 CB 5 0.5 30/0/30 CC 10 1 30/0/60 CD 10 1

30/0/100 CE 20 2 30/0/150 CF 20 2 30/0/300 CH 50 10

0/15 B 2 0.2 0/30 C 5 0.5 0/60 D 10 1

0/100 E 20 2 0/160 F 20 2 0/200 G 40 4 0/300 H 50 5 0/400 I 50 5 0/500 J 100 10 0/600 K 100 10 0/800 L 100 10

0/1000 M 200 20 0/1500 N 200 20 0/2000 O 400 50 0/3000 P 500 50 0/4000 Q 500 50 0/5000 R 1000 100 0/6000 S 2000 200

0/10,000 U 2000 200 0/15,000 V 2000 200

Som

e ra

nges

not

ava

ilabl

e in

all

dial

size

s, pl

ease

cal

l with

you

r par

ticul

ar

A B C D E F 2 ½" In 2.92 .64 1.03 2.87 1/4“ 1.06 Dial MM 74 16 26 73 NPT 27

Our ‘701L’ series gauge line is a high quality line of plastic case liquid filled gauges. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement (and keeping contaminates such as dirt away from all moving parts) which will extend the life of the gauge. This gauge has been specifically designed with the original equipment manufacturers in mind and are typically used on hydraulic & pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts where glycerine filling is suitable for use.

CONTRACTOR SERIES GAUGE


Diaphragm Seals Needle Valve & Gauge

Valves Snubbers, Siphons & Accessories

PART NUMBER RANGE MAJOR MINOR CONTRACTOR-4LA 30”HG VAC 5”hg 2”hg CONTRACTOR-4LCC 30/0/30 5 psi 1 psi CONTRACTOR-4LCE 30/0/100 10 psi 1 psi CONTRACTOR-4LCF 30/0/150 25 psi 2.5 psi CONTRACTOR-4LB 0/15 2.5 psi .25 psi CONTRACTOR-4LC 0/30 5 psi 1 psi CONTRACTOR-4LD 0/60 10 psi 1 psi CONTRACTOR-4LE 0/100 10 psi 1 psi CONTRACTOR-4LF 0/160 20 psi 2 psi CONTRACTOR-4LG 0/200 20 psi 2 psi CONTRACTOR-4LH 0/300 50 psi 5 psi CONTRACTOR-4LJ 0/500 50 psi 5 psi

These gauges have been designed and built with the contractor in mind. With a price that makes this the most attractive gauge for use on any project where bronze internals are suitable for use. Some typical applications are; air, water, gas, oil and steam* (* a pigtail siphon should always be used when putting any gauge into steam service).

STANDARD FEATURES • Stainless steel case (for rust and corrosion resistance) • Plastic lens (to resist breakage & won’t shatter)

• +/- 1 % full scale accuracy • Zero adjust screw on dial (for additional fine tuning)

• Large easy to read numbers on single scale PSI only dial

A B C INCHES 4.9” 1.17” .97” MM 124 30 25

115D SERIES GAUGE These 4 ½”, 6” & 8 ½” gauges have been designed and built primarily for the industrial market. They are well suited for all applications where bronze tube and socket are suitable for use. Some typical applications are; air, water, gas, oil and steam* (* a pigtail / siphon should always be used when putting any gauge into steam service) STANDARD FEATURES • Heavy Duty Black Steel Case (Epoxy Coated For Rust And Corrosion Resistance) • Plastic Lens* (To Resist Breakage)

(*Glass on 8 ½”Dial Size) • + / - 1% Full Scale Accuracy (ANSI Grade A) • Single Scale PSI only Standard

(Dual Scale Available upon request) • Removable Back Flange (For More Diversity From Stock)

Note:

All typical accessory type items such as gauge

cock’s, pigtail/siphons, snubbers, needle valves or diaphragm seals can be provided with gauges

upon request.

Part Number Major Minor 4 ½” 6” 8 ½” RANGE inc inc

115D-454A 115D-604A 115D-854A 30”HG VAC 5”hg 2”hg 115D-454CC 115D-604CC 115D-854CC 30/0/30 5 PSI 1 PSI 115D-454CE 115D-604CE 115D-854CE 30/0/100 10 PSI 1 PSI 115D-454CF 115D-604CF 115D-854CF 30/0/160 25 PSI 2.5 PSI 115D-454B 115D-604B 115D-854B 0/15 115D-454C 115D-604C 115D-854C 0/30 5 PSI 1 PSI 115D-454D 115D-604D 115D-854D 0/60 10 PSI 1 PSI 115D-454E 115D-604E 115D-854E 0/100 10 PSI 1 PSI 115D-454F 115D-604F 115D-854F 0/160 20 PSI 2 PSI 115D-454G 115D-604G 115D-854G 0/200 20 PSI 2 PSI 115D-454H 115D-604H 115D-854H 0/300 50 PSI 5 PSI 115D-454K 115D-604K 115D-854K 0/600 100 PSI 10 PSI

4 ½” Dial size 6” Dial size 8 ½”Dial size In. MM In. MM In. MM

A 4.99” 125 5.95” 151 8.56” 216 B 5.41” 138 6.87” 175 9.44 240 C 5.87” 149 7.42” 188 10.25 260 D 6.79” 172 8.41” 213 10.75” 272 E 1.40” 36 1.61” 41 1.27” 32 F 1.86” 47 1.86” 47 1.93” 49 G .18” 4.5 .24” 6 .14” 3.5

LP SERIES LOW PRESSURE

SPECIFICATIONS FEATURES

• Chrome plated case • Black steel case (u-clamp panel mnt) • Brass internals and connection • Dry non-fillable • +/- 1.5 % accuracy

• 2 1/2"dial size with twist lock plastic lens • zero adjustment screw on back of case • 1/4"mnpt bottom or back connection • Capsule type diaphragm to measure low pressures

2 ½” 4” IN MM IN MM A 2.60" 66 3.98” 101 B 1.70" 44 2.21” 56 C .85" 22 1.56” 40 D 3.45" 87.5 5.49” 139 E 1/4”NPT 1/4" OR 1/2" NPT F 2.60” 66 3.98” 101

LP1

G 2 ½” 4” IN MM IN MM

A 2.62" 66.5 ---- ---- B 1.92" 49 ---- ---- C .84" 21.5 ---- ---- D 2.75" 71 ---- ---- E 1/4”NPT ---- ---- F 2.60" 66 ---- ----

LP2

G ---- ---- 2 ½” 4” IN MM IN MM

A 2.84" 72 ---- ---- B 1.88" 48 ---- ---- C .84" 21.5 ---- ---- D 2.74" 69.5 ---- ---- E 1/4”NPT ---- ---- F 2.60" 66.2 ---- ----

LP3

G 2.84 72 ---- ---- 2 ½” 4” IN MM IN MM

A 2.61 66 ---- ---- B 1.89 48 ---- ---- C .875 22.2 ---- ---- D 2.74 69.5 ---- ---- E 1/4”NPT ---- ---- F 2.67 68 ---- ----

LP4

G 3.44 87.4 ---- ---- AVAILABLE RANGES: 200-0”wc Vacuum (2”Minor inc) 0-30”wc ( .5”wc minor inc.) 0-3 psi ( .05 psi minor inc.) 160-0”wc Vacuum (2”Minor inc.) 20 oz./35”wc ( .5”wc minor inc.) 0-5 psi ( .1 psi minor inc.) 100-0”wc Vacuum (1”Minor inc.) 35 oz./60”wc ( 1”wc minor inc.) 0-10 psi ( .2 psi minor inc.) 60-0”wc vacuum (1”Minor Inc.) 0-60”wc ( 1”wc minor inc.) 30-0”wc vacuum ( .5”wc minor) 0-100”wc (2”wc minor inc.) 0-10”wc (.5”wc minor inc.) 0-160”wc (5”wc minor inc.) 0-15”wc ( .2”wc minor inc.) 0-200”wc (5”wc minor inc.)

NOTE: OTHER RANGES AVAILABLE UPON REQUEST, PLEASE CALL WITH ANY INQUIRIES

DIGITAL PRESSURE GAUGE Product Description PIC’s line of bulk micro-machined, gage and sealed gage digital pressure gauges for both harsh and benign media with the superior accuracy of ±0.25% typical represents a significant cost savings over currently available digital gauges. These compact, robust gauges measure pressures from 15 Psi to 5,000 Psi and are well suited for a variety of industrial and commercial applications. PIC, a leading OEM supplier of pressure gauges…having developed full lines of industrial and process gauges, offers the Digital Pressure Gauge, targeted at OEM, industrial and commercial applications where cost, size, and performance are critical.

Special Features Superb Accuracy – ±0.25% Robust Package – All laser-welded stainless steel design for optimal media isolation Maximum Flexibility – Custom ASIC provides signal conditioning for calibration and temperature compensation of 0-50°C Standard and custom options available Compact size, excellent price/performance ratio 8 – 30 Volt input with 4 – 20 mA output (optional)

(Pictured with optional rubber

cover)

Typical Applications Refrigeration n Compressors Pumps n Flow Hydraulics n Agriculture Process Control in Hydrogen Storage Spraying Systems in Waste Water Pneumatics in General Industrial

Standard Full Scale Pressure Ranges 15, 100, 300, 1000, 3000 and 5000 Psi ±0.25% Accuracy (BFSL) Typical, Least 1 Significant Digit 4-20 mA output (optional) High and Low Limit Set Points (optional) Back Lit Display Zero Reset Multiple Pressure Units (PSI, BAR, kPa)

Performance Specifications (all values at 22°C unless noted otherwise)

Output Type Standard 4 – 20 mA 75-3000 PSI ±0.25% FS Least 1 Significant Digit ±0.25% FS Least 1 Significant Digit Accuracy

(Typical) 15-50 PSI ±0.50% FS Least 1 Significant Digit ±0.50% FS Least 1 Significant Digit 75-3000 PSI ±0.25% FS Least 1 Significant Digit ±0.25% FS Least 1 Significant Digit Thermal Error

(-10°C to 60°C) (Typical) 15-50 PSI ±0.50% FS Least 1 Significant Digit ±0.50% FS Least 1 Significant Digit

75-3000 PSI ±0.25% FS Least 1 Significant Digit ±0.25% FS Least 1 Significant Digit Total Error (Typical)

15-50 PSI ±0.50% FS Least 1 Significant Digit ±0.50% FS Least 1 Significant Digit

Stability (Typical) < 0.25% FS/Year < 0.25% FS/Year Zero Pressure Offset 4 mA

Full Scale Output 20 mA

Operating Temperature -10° to 60°C -10° to 60°C

Storage Temperature -20° to 85°C -20° to 85°C

Proof Pressure 3 x FS 3 x FS

Burst Pressure 5 x FS 5 x FS

Electrical Specifications Output Type 4 – 20 mA Supply Voltage 9V Battery 8 to 30 Volts

Response Time < 1 ms < 1 ms

Reverse Polarity Protection N/A Yes

Reliability And Environmental Performance Test Conditions Value Units

Wetted Materials 304L & 316L Stainless Steel – –

Pressure/Temperature Cycles 0 to FS @ 8Hz; and -20° to 85°C >1.8x106 Cycles

Thermal Shock 85°C to -20°C, 0.5 hr soaks at Temp. (2s Transfer) 250 Cycles

Vibration 100 to 2050 Hz, 20 Sinusoidal, 3 Axes 144 Hours

EMC Compatibility 80 MHz - 1 GHz 100 V/M

Humidity 40°C and 90% to 95% R. H. 250 Hours



For more information, Please contact:

Precision Instrument Company 3295 Cobb International Blvd * Kennesaw, GA 30152

Toll Free: (888) 650-6923 * Fax: (770) 429-0795 Web: www.PICgauges.com Email: [email protected]

BULK-HD TRUCK MOUNT GAUGE

(These 4 ½” gauges have been designed and built primarily for the Dry Bulk Tanker Market.)

Note: All typical accessory type items such as gauge cock’s, pigtail/siphons, snubbers, needle valves or diaphragm seals can be provided with gauges upon request.

Part Number Major Minor 4 ½” Range inc inc

BULK-HD-454L-CC 30/0/30 5 psi 1 psi BULK-HD-454L-C 0/30 5 psi 1 psi

4 ½” Dial Size In. MM

A 4.95” 126 B 5.43” 138 C 5.90” 150 D 6.34” 161 E .98” 25 F 1.34” 34 G .20” 5

STANDARD FEATURES • Case: Epoxy Coated Black Steel Case w/Removable Back Flange

Epoxy Coated For Rust And Corrosion Resistance Removable Back Flange for more diversity from stock

• Movement: Heavy-duty stainless steel movement for better accuracy and durability.

• Anti-vibration: We added a silicone dampened counter weight attached to the movement, allowing the gauge to function as a liquid-filled gauge, but eliminating the problems associated with liquid filling (i.e. browning and leakage).

• Bourdon Tube: Large Heavy-duty type bourdon tube adds to the accuracy and durability

• Adjustable Pointer: High Quality industrial grade micrometer pointer making recalibration easier and more accurate.

• Wetted Parts: Brass Socket / Bronze Internals • Lens: Plastic Lens Resists Breakage • Accuracy: 1 % of Full Scale • Dial Single: Scale PSI Only With Large Easy To Read Numbers

VALVE POSITIONER GAUGES

PIC has developed a line of positioner gauges that cover the needs of most positioner applications – from ½” to 1 ½”Dial Size.) with brass or stainless steel internals, dry or liquid filled, plastic, steel or stainless steel case.

(Note: ½” and ¾”dial size by special order only See the list below and call or Email for further information and more details

40MM-BR-158

40mm Dial Stainless Case

Plastic Lens Brass Internals Liquid Fillable

40MM-SS-158 40mm Dial

Stainless Case Plastic Lens

316ss Internals Liquid Fillable

102D-158 1 ½” Dial

Black Steel Case Plastic Lens

Brass Internals Chrome Bezel

102D-SS-158 1 ½” Dial


Brass Internals Chrome Bezel

202D-158x-POS 1 ½” Dial


Brass Internals Snap in Lens

102D-108 1” Dial

Plastic Case Plastic Lens

Brass Internals Mini Gauge

202D-158 1 ½” Dial


Brass Internals Dry

202L-158 1 ½” Dial


Brass Internals Liquid Filled

302DNF-158 1 ½” Dial

Stainless Case Glass Lens

Stainless Internals Stainless Bezel

302L-158 1 ½” Dial


Stainless Internals Liquid Filled

Positioners attach to actuators on different types of valves and regulators – controlling many aspects of process variables including Pressure, Flow, Temperature and motion. This includes process heating, cooling, mixing, etc and the list goes on. Positioners have pressure gauges mounted on them to monitor air supply and controlled output for 2 or more movements

(Typically P1 is for actuation, P2 if for return to normal). These gauges are mounted in a small area close together, close to the valve and positioner body - so dial size is critical.

Note: Pictures are for application illustration only. Pictures do not indicate any positioner manufacturer is or is not using our product, has approved our product for use or recommend our gauges over others

40MM POSITIONER GAUGE

SPECIFICATIONS: DIMENSIONS:

• Dial Sizes: 40mm • Connection Sizes: 1/8”MNPT • Stainless Steel Case And Bezel • SS Internals & Connection • Case Welded at Connection • 316SS Bourdon Tube • Liquid Filled (Dry Available) • Accuracy : Standard = 2-1-2 % Per ANSI grade B


DRY: -30˚F to 180˚F


0/100 E 20 2 0/160 F 20 2

Our ‘40MM’ series gauge is a small diameter, high quality positioner gauge made of all stainless steel. Hermetically sealed and liquid fillable, this gauge incorporates the best features available in a small diameter pressure gauge. The hermetical seal prevents dust, dirt or other contaminates from entering the case, while the available liquid filling can help dampen shock and vibration and lubricate the movement and internals of the gauge. These features prolong the life of the gauge. This gauge has been specifically designed with original equipment manufacturers in mind where size and cost are critical factors. These gauges are also well suited for any commercial or industrial application where stainless steel components are required.

A B C D E Inches 1.61” 1.02” .84” 1.76”

MM 41 26 21 45

1/8” Npt

Front View Side View Back View

40MM SS C

PART NUMBERS:

SS = All Stainless Steel Construction40MM Dial Size

PANEL MOUNT GAUGES

104D 1 ½”, 2”, 2 ½”, 3 ½”Dial

Front Flanged, Dry Gauge Steel Case, Brass Internals

204L 1 ½”, 2”, 2 ½”, 4”Dial

Front Flanged, Liquid Filled SS Case, Brass Internals

304L 1 ½”, 2”, 2 ½”, 4”Dial

Front Flanged, Liquid Filled SS Case, 316SS Internals

314LB 2 ½”Dial

Front Flanged, Fillable SS Case, 316SS Internals

314D 4”Dial


6004 6”Dial


4504 4 ½”Dial

Front Flanged, Dry Aluminum Case, 316SS Internals

6504 6”Dial

Front Flanged, Dry Alum Case, 316SS Internals

103D 1 ½”, 2”, 2 ½”, 3 ½”Dial U-Clamp, Dry Gauge

Steel Case, Brass Internals

203L 1 ½”, 2”, 2 ½”, 4”Dial

U-Clamp, Liquid Filled SS Case, Brass Internals

303L 1 ½”, 2”, 2 ½”Dial

U-Clamp, Liquid Filled SS Case, 316SS Internals

313LB 2 ½”Dial

U-Clamp, Fillable SS Case, 316SS Internals

501D-UNO OIL FREE SERVICE

SPECIFICATIONS: • Available Dial Sizes: 2 or 2 ½” • Connection Sizes:1/4"MNPT • Highly Polished Brass Case • Copper Alloy Movement & Connection • Copper Alloy Bourdon Tube

(Low Copper Content for use with acetylene) • Twist-on Plastic Lens • Dry Gauge, for “Oil Free Service” • Pressure Relief Disc On Back Of Case • Accuracy : 2.5 % of Span (Grade B ANSI B40.1) • Single Scale, PSI only • Ambient temperature: -4˚F to 140˚F


0/100 E 20 2 0/200 G 40 4 0/400 I 50 5

0/4000 Q 500 50

Other Ranges, Dials Sizes and Connection Locations available, please call with your particular application

A B C D E 2” In 2.31 1.2 2.07 1.13 1/4“

Dial MM 59 31 53 29 Npt 2 ½" In 2.83 1.13 2.65 1.13 1/4“ Dial MM 72.0 29 68 29 Npt

Our ‘501D-UNO” (Use No Oil) gauges have been designed and manufactured for oil free service indicating cylinder pressure of compressed non-corrosive gases or any medium which oxidizes with oil based materials, in applications such as welding, cutting and related processes.

A utility gauge designed for use where water depth or head pressure and/or equivelant psi pressure need to be known. This gauge is suitable for air, water, oil, gas or any other media not corrosive to brass. Other connection locations, mounting styles and accessories available upon request. A complete explanation of use of this gauge is available upon request.

ALTITUDE BOTTOM CONNECTED

GENERAL DIMENSIONS 3 ½” or 4 ½” Dial Size, ¼”NPT Bottom Conn

GENERAL SPECIFICATIONS: Black Steel Case With Chrome Bezel Dual Scale Dial with Adjustable Red Set Hand Brass Socket And Movement Phosphor Bronze Bourdon Tube Dry Non-Fillable 3-2-3 % Accuracy Ambient Temperature: -50 to 160˚F DIAL SCALE: DUAL SCALE: PSI & FEET of Water Col STANDARD SINGLE SCALE: FEET ONLY AVAILABLE OTHER: (metric, etc) BY SPECIAL REQUEST

RANGE CODE Major Inc. Ft of water 0/15 B 2 PSI 34’ 0/30 C 5 PSI 70’ 0/60 D 10 PSI 140’ 0/100 E 20 PSI 230’ 0/160 F 20 PSI 370’ 0/200 G 40 PSI 460’ 0/300 H 50 PSI 690’

A B C D E 3 ½" In. 3.53" 1.14” 1.02” 4.55” 1/4

Dial MM 90 29 26 116 MNPT

4 ½" In. 4.89" 1.16” 1.16” 6.05” 1/4

Dial MM 124 29 30 154 MNPT

Note: 1. For tower or tank depth or head pressure

gauge should be mounted at the lowest possible point as pressure/depth reading is from gauge level up.

2. For well depth or tank depth where gauge is

mounted above maximum fill line, gauge must be mounted on air line going into top of tank (or well) and straight down vertically to maximum depth to be measured.

AMMONIA REFRIGERATION

2 ½” & 4”LIQUID FILLED GAUGES

Description

Stainless Steel Case 316SS Tube & Socket Removable Bezel Adjustable Pointer Plastic Lens Glycerine Filled 1 % Accuracy

1/4”NPT or 1/2"NPT Bottom or Back Mount Stem Mount or Panel Mount Flangeless, Front Flange or Back Flange Liquid Filled or Dry

2 ½” & 4”Dry – Chrome Case Gauges Description

Chrome Plated Steel Case Steel Tube & Socket Removable Bezel Adjustable Pointer Plastic Lens

1/4"Bottom Connection Other Configurations Available upon request

4 ½”DIAL PROCESS GAUGES Description mbers

Polypropylene Case Turret Style with Back Flange 316SS Tube & Socket Laminated Safety Glass Lens 0.5 % Full Scale Accuracy Adjustable Pointer

1/4”NPT or 1/2"NPT Bottom or Back Mount Stem Mount or Panel Mount Flangeless, Front Flange or Back Flange Liquid Filled or Dry Stainless Steel Case Available also

6”Dial All Stainless Steel Description

Stainless Steel Case 316SS Tube & Socket Laminated Safety Glass Lens Adjustable Pointer

1/4”NPT or 1/2"NPT Bottom or Back Mount Stem Mount or Panel Mount Flangeless, Front Flange or Back Flange Liquid Filled or Dry

8 ½”Dial Description

Black Steel Case 316SS Tube & Socket 1 % Full Scale Accuracy Removable Bezel Adjustable Pointer

1/4"NPT Lower Back Connection, Back Flange Other Configurations Available upon request

AMMONIA GAUGES

Liquid Filled Gauges For Ammonia Refrigerant Description Model Numbers

Range (Press = Temp) 2 ½” Dial Size -30/0/150 = -40 to + 85˚F AMMONIA-LF-254CF -30/0/300 = -40 to + 125˚F AMMONIA-LF-254CH

Range (Press = Temp) 4”Dial Size -30/0/150 = -40 to + 85˚F AMMONIA-LF-404CF

Stainless Steel Case 316SS Tube & Socket Removable Bezel Adjustable Pointer Plastic Lens Glycerine Filled 1 % Accuracy -30/0/300 = -40 to + 125˚F AMMONIA-LF-404CH

Dimensions 2 ½” 4” Inches MM Inches MM

A 2.75 70 4.36 110 B 1.36 34 1.73 44 C 1.00 25 1.38 35 D 3.48 88 5.26 133 E 1/4” MNPT 1/4” MNPT

G .78 20 1.06 27

Dry – Chrome Case Gauges For Ammonia Refrigerant Description Model Numbers

Range (Press = Temp) 2 ½” Dial Size -30/0/150 = -40 to + 85˚F 401A-254CF -30/0/300 = -40 to + 125˚F 401A-254CH

Range (Press = Temp) 4” Dial Size -30/0/150 = -40 to + 85˚F 401A-404CF

Chrome Plated Steel Case Steel Tube & Socket Removable Bezel Adjustable Pointer Plastic Lens

-30/0/300 = -40 to + 125˚F 401A-404CH Dimensions

2 ½” Dial Size 4” Dial Size Inches MM Inches MM

A 2.87 73 4.21 107 B 1.14 29 1.35 34 C 2.65 67 3.89 99 D .84 21 1.03 26

E 1/4” MNPT 1/4” MNPT

Dry – Black Steel Case Gauges for Agricultural Ammonia Description Dimensions

2 ½” Inches MM

A 2.50 63.5

Black Painted Steel Case Steel Tube & Socket Plastic Lens Accuracy: 3-2-3 %

B 1.13 29 Model Numbers C .99 25

D 3.40 86

0-60 PSI = 401A-254D 0-160 PSI = 401A-254F 0-400 PSI = 401A-254I E 1/4” MNPT

401DFW AMMONIA GAUGES

SPECIFICATIONS: • Dial Sizes: 2 ½” or 4" • Connection Sizes: 1/4"MNPT • All Welded Case & Connection • Stainless Steel Case And Bezel • Plastic Lens • SS Internals • 316 SS Bourdon Tube & Connection • Built in Snubber (for Extra Dampening Effect) • Dry (Liquid Filled Available) • Accuracy : 2 ½”Dial Size = 1.5 %

4” Dial Size = 1 % • Dual Scale: PSI & ‘F Temp Equivalent

(Metric Scale available) • Ranges Available:

30/0/150 PSI & -40/0/80’F 30/0/300 PSI & -40/0/120’F

• Ambient temperature: DRY: -40˚F to 180˚F Glycerine Filled: 30˚F to 160˚F Silicone Filled: -50˚F to 300˚F



A B C D E In 2.67” 1.22” 1.06” 3.60” 2 ½"

Dial MM 68mm 31mm 27mm 92mm

1/4“ NPT

In 4.21” 1.42” 1.34” 5.40” 4" Dial MM 107mm 36mm 34mm 137mm

1/4" NPT

Our ‘401’ series gauge line is a competitive line of ammonia gauges, designed with the original equipment manufacturers in mind. Available dry, glycerine filled or silicone filled, these gauges are suitable for use on most ammonia refrigeration systems

These gauges are liquid fillable: the liquid filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement (and keeping contaminates such as dirt away from all moving parts) which will extend the life of the gauge. Also the case and connection are welded preventing possible leakage at the bottom of the case. Although these gauges are the best mix of quality and price we also stock a full line of ammonia gauges available in various dial sizes, connections and case designs.

AGRICULTURAL AMMONIA GAUGES

401A – Black Steel Case Gauges for Agricultural Ammonia Description DIMENSIONS

2 ½” 4” Dimensions

A 2.50” 3.95”

Black Painted Steel Case SS bourdon Tube, Steel Socket Plastic Lens Accuracy: 3-2-3 % B 1.17” 1.40” Model Numbers C .86” 1.00”

D 3.36” 4.95” E 1/4” MNPT

Range = 2 ½”Dial or 4”Dial 0-60 PSI = 401A -254D or -404D 0-160 PSI = 401A -254F or -404F 0-400 PSI = 401A -254I or -404I

These gauges have a SS bourdon tube with steel socket. They are designed for use on the agricultural sprayer equipment that distributes and stores; ammonia fertilizers, chemical herbicides, pesticides as well as the fluids used for cleaning the equipment. Crop protection chemicals are most effective when applied at proper rates. The spreading of the different types of chemicals over crops is critical to the health of the plants, environment and ultimately consumers. Over applications of any of these chemicals can greatly increase the cost per acre for application, destroy crops or pollute the environment, while under application can lead to smaller unhealthy crops. To achieve satisfactory spray coverage, spray application equipment must deliver proper application rates in gallons per acre and desirable application pressures in pounds per square inch, The actual range used will depend on the stage of crop growth (size) and the time and method of application. Proper calibration assures safe, economical and effective practices. To correctly calibrate sprayers - pumps, nozzles, pressure regulators and gauges must be properly maintained. Our gauges are used to set and monitor line pressure to the nozzles.

• Suitable for air, water, oil, gas or any other media not corrosive to brass. • Mounting accessories (Mounting Brackets) available. • Ready for immediate shipment upon request.

RECTANGLE (EDGE) GAUGE

SIZE: 1 ¾” x ½” HORIZONTAL OR VERTICAL

CONNECTION SIZES: 10-32” Female Thread Or 1/32” Hose Barb Connection

GENERAL SPECIFICATIONS: Plastic Case , Polycarbonate Lens Brass Bourdon Tube Single Or Dual Scale 5 % Accuracy Full Scale Ambient Temperature: -50 To 160˚F With Or Without Mounting Bracket SCALE: DUAL SCALE: PSI & KG/cm2 STANDARD SINGLE SCALE: PSI ONLY AVAILABLE OTHER: BY SPECIAL REQUEST

Inches mm

A 1.76” 45

B 2.28” 58

C .51” 13mm

D .43” 11mm

GT SERIES GAS TEST GAUGES

DESIGNED FOR THE INSTALLER

Our popular and proven hex-shaped body static pressure test assemblies are now available in

horizontal or vertical mount. They can be installed with a standard wrench, reducing the chance of slipping, are chrome plated to prevent rust and corrosion and include a quality bourdon tube type pressure gauge in whatever range you require.

STANDARD RANGES AVAILABLE: 0-15 PSI (1/10th or .1 PSI Minor Increments)

0-30 PSI (1/4 or .25 PSI Minor Increments) 0-60 PSI (1/2 or .5 PSI Minor Increments) 0-100 PSI (1 PSI Minor Increments) 0-160 PSI (2 PSI Minor Increments)

NOTE: OTHER RANGES AVAILABLE UPON REQUEST, PLEASE CALL WITH ANY INQUIRIES.

SPECIFICATIONS: • GAUGE:

2” Dial Size Black Steel Case Bourdon Tube Type Pressure Gauge Brass Bourdon Tube And Socket Snap In Plastic Lens

3-2-3 % Accuracy • BLOCK: Chrome plated steel block Chrome air valve with plastic cap Hex shaped body for easier Installation Vertical or Horizontal Mounting ½”, ¾” or 1” FNPT Connections Available

FEATURES: • AVAILABLE IN MANY PRESSURE RANGES • LARGE PRINT ON SINGLE SCALE DIAL FOR EASY READING • AVAILABLE HORIZONTAL OR VERTICAL MOUNT • AVAILABLE WITH ½”, ¾” OR 1”FNPT BLOCK • NOW AVAILABLE WITH BELL SHAPE HOUSING

NPT A B C D E F G H HORIZONTAL MOUNT VERSION

½” 2.13”/54.10MM 2.81”/71.45MM 2.02”/51.35MM 2.56”/65.02MM 1.03”/26.29MM

¾” 2.13”/54.10MM 2.81”/71.45MM 1.13”/28.80MM 2.02”/51.35MM 2.56”/65.02MM 1.03”/26.29MM 1.33”/33.92MM

1” 2.13”/54.10MM 2.81”/71.45MM 1.40”/35.60MM 2.02”/51.35MM 2.56”/65.02MM 1.03”/26.29MM 1.60 “/40.63MM

VERTICAL MOUNT VERSION ½” 2.13”/54.10MM 2.81”/71.45MM 2.02”/51.35MM 2.56”/65.02MM 1.03”/26.29MM

¾” 2.13”/54.10MM 2.81”/71.45MM 1.13”/28.80MM 2.02”/51.35MM 2.56”/65.02MM 1.03”/26.29MM 1.33”/ 33.92MM

1” 2.13”/54.10MM 2.81”/71.45MM 1.40”/35.60MM 2.02”/51.35MM 2.56”/65.02MM 1.03”/26.29MM 1.60”/ 40.63MM

‘HOSE’ SERIES HOSE TEST

DIMENSIONS: ‘HOSE’ ‘HOSE-MAX’

SPECIFICATIONS: • GAUGE: 0-300 PSI

Bourdon Tube Type Pressure Gauge 2 ½” Dial Size Black Plastic Case Brass Bourdon Tube And Socket Plastic Lens, 3-2-3 % Accuracy

• Top Connection - 3/4” Female Brass Hose Coupling & Tail Piece with Rubber Washer

• Available with or without Maximum Indicating Pointer

INCHES MM A 2.83 72 B 1.18 31 C 1.14 29 D .57 14.5 E 1.22 31 F .2 5

INCHES MM A 2.56 65 B 1.21 31 C 1.14 29 D .57 14.5 E 1.22 31

509L LONG WALL MINING GAUGE

SPECIFICATIONS: • Dial Sizes: 2” Diameter • Connection: “Steck-o” Type

Mining Industry Standard Special Hydraulic Quick Connect with Buna Sealing O-Ring and Nylon Washer.

• 1pc Forged Brass Case and Connection • Stainless Steel Bezel • Plastic Lens • Brass Internals • Phosphour Bronze Bourdon Tube • Liquid Filled (Dry Available) • Accuracy : Standard = 1.5 % • Dual Scale: 9000 PSI & 600 Bar w/ Red, Green & Yellow Zones • Ambient temperature: Liquid Filled : 30˚F to 160˚F

Dry : -30˚F to 180˚F

A B C D E F G H I J K L 2" In 2.1 1.96 .44 1.13 .785 .55 .30 .20 .19 .19 .125 .125

Dial MM 53.34 49.78 11.18 28.70 19.94 13.97 7.61 5.08 4.82 4.82 3.17 3.17

Our ‘509L’gauge is a high quality liquid filled gauge designed specifically for the mining industry. With a heavy duty one-piece forged brass case and connection this gauge is built to be extra durable. The silicone filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement, keeping contaminates such as dirt and coal away from all moving parts, which will extend the life of the gauge. What makes it specific to the mining industry, is the special quick connect bottom connection and 0-9000 psi triple color dial. This gauge has been specifically designed with original equipment manufacturers in mind. It is typically used on the cylinders for the roof support shields on long wall mining equipment and hydraulic systems for the mining industry.

102D-108 1”MINI GAUGE

These gauges are designed for applications where its small diameter fits in close quarters or where pressure readings are required but larger gauges cannot be used. With a plastic case and brass internals this gauge is suitable for use for; water, air, gas, oil, steam or any other process not corrosive to its brass internals.

A B C D E INCHES .99" .64” .46” 1.61” 1/8”

MM 25mm 16mm 12mm 41mm NPT

RANGE CODE 0/30 C 0/60 D 0/100 E 0/160 F

DIAL SIZES: 1” CONNECTION SIZE: 1/8"MNPT SPECIFICATIONS: PLASTIC CASE WITH PLASTIC LENS BRASS INTERNALS AND CONNECTION DRY NON-FILLABLE 3-2-3 % ACCURACY

FOR USE WHERE SIZE MATTERS This gauge with it’s unique solid 1 piece case and connection, coupled with a direct drive spiral tube and built-in filter type snubber makes a very rugged designed gauge suitable for severe applications.

1”HEX - HIGH PRESSURE GAUGE

GENERAL SPECIFICATIONS: 1”Case x 1/8”NPT Center Back Connection Chrome Plated Hex Case Plastic Lens Dry Non-Fillable Bronze Spiral Tube 5 % Accuracy Ambient Temperature: -50 to 160˚F Built-in Filter type Snubber SINGLE SCALE PSI ONLY AVAILABLE OTHER: BY SPECIAL REQUEST

RANGE CODE Major Inc. Minor inc. 0/300 H 0/500 J 100 PSI 20 PSI 0/700 KE 0/750 KF 0/1200 MG 0/4000 Q 0/5000 R 1000 PSI 200 PSI 0/6000 S

A B C D 1" In. 1” .40” .35” 1/8”

Dial MM 25.09 10.17 8.89 MNPT

SAE-201L BOTTOM CONNECTED

SPECIFICATIONS:

• Dial Sizes: 2 ½” Diameter • Connection:

7/16”–20 SAE Hydraulic Connection with Rubber O-Ring, Washer and Lock Nut

• Stainless Steel Case And Bezel • Brass Internals & Connection • Phosphour Bronze Bourdon Tube • Liquid Filled (Dry Available) • Accuracy : Standard = 1.5 %


DRY: -30˚F to 180˚F

A B C D E In 2.80 1.28 1.07 3.55 2 ½"

Dial MM 71 33 27 90 7/16”-20

SAE

Our ‘200’ series gauge line is a high quality line of liquid filled gauges. The glycerine filling helps dampen the effects of pulsation and vibration, while also perpetually lubricating the movement (and keeping contaminates such as dirt away from all moving parts) which will extend the life of the gauge. This gauge has been specifically designed with original equipment manufacturers in mind. It is typically used on hydraulic & pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts where glycerine filling is suitable for use.

SPIRAL TUBE, DIRECT DRIVE

SPECIFICATIONS:

• Dial Sizes: 1 1/8” OR 1 1/2” • Connection Sizes: 1/8"MNPT • SS Case / Plastic Lens • Brass Connection • Phosphour Bronze Bourdon Tube • Dry Gauge (Filled Not Available) • Accuracy : 5 % • Single Scale available from stock • Ambient temperature: FILLED: 30˚F to 160˚F

A B C D E F G Inches 1.4” 1.2” .16” .25” .28” .32” 1 1/8"

Dial MM 36 30.5 4 6.5 1/8” NPT 7.2 8

Inches 1.65” 1.46” .23” .23” .23” .33” 1 1/2” Dial MM 42 37 6 6

1/8” NPT 6 8.5

Our spiral tube direct drive gauge line is a high quality line of direct drive gauges designed for constant vibration applications such as pumps and compressors, where the direct drive (no movement) gauge will outlast standard bourdon tube type pressure gauges. This gauge has been specifically designed with the original equipment manufacturers in mind and are typically used on pneumatic systems as well as any commercial or industrial application not corrosive to brass and bronze wetted parts.

• UL listed pressure gauges designed for use in the fire protection/sprinkler market. • Suitable for air, water, oil, gas or any other media not corrosive to brass. • Other Ranges, connection locations, mounting styles and accessories available. • Ready for immediate shipment upon request.

‘SPRINKLER’ FIRE PROTECTION

DIAL SIZE: 3 ½”

CONNECTION SIZE: ¼”NPT

GENERAL SPECIFICATIONS: Brass Case or Plastic Case Screw-on Molded Plastic Lens & Bezel Brass Socket And Movement Phosphor Bronze Bourdon Tube Dry Non-Fillable 3-2-3 % Accuracy Ambient Temperature: -50 to 160˚F DIAL SCALE: SINGLE SCALE: PSI ONLY STANDARD DUAL SCALE: PSI & BAR (x100=kPa) AVAILABLE OTHER: BY SPECIAL REQUEST

Part Number RANGE Case Major Inc. Minor inc. SPRINKLER-1 0/300 Brass 25 PSI 5 PSI SPRINKLER-2 0/300 Plastic 25 PSI 5 PSI SPRINKLER-3 0/80-250 Brass Retard – Non-linear Scale

A B C D E 3 ½" In. 3.875" 1.15” 3.71” 1.08” 1/4 Dial MM 98 29 94 27.5 MNPT

Stocked Accessories: Pigtail Siphons Test Plugs

Gauge Cock Diaphragm Seals

Snubbers

STANDARD GAUGE ACCESSORIES

A14 Ball Valve Type Gauge Cock ¼”FNPT x ¼”FNPT

Brass Body Rating: 700 PSI at 250˚F

A15 Ball Valve Type Gauge Cock ¼”FNPT x ¼”MNPT

Brass Body Rating: 700 PSI at 250˚F

NV-B-1/4 Needle Valve ¼”FNPT x ¼”FNPT

Brass Body Rated at 5000 PSI

Please also see our full line of instrumentation type needle valves:

Super Mini Mini Full Size Hex Body Multi-Port

A B Inches 1.62” 1.94”

mm 41mm 49mm

A B

Inches 1.60” 1.30” mm 40mm 33mm

A B

Inches 1.60” 1.35” mm 40mm 34mm

PIGTAIL SYPHONS

Pigtail Siphons are typically used to act as a cooling or warming leg for applications where the process temperature is higher or lower than the ‘normal working temperature range as specified by NIST B40.1 in relation to instrumentation. Temperature extremes can cause inaccuracy or shorten the life span of instruments not specifically designed for severe duty applications.

Part No. Description Pressure TemperatureA03B ¼”NPT Brass Pigtail 250PSI 400˚F A031 ¼”NPT Iron Pigtail, Schedule 40 Iron 500PSI 400˚F CPS4 ¼”NPT Steel Pigtail, Schedule 80 Steel 1000PSI 850˚F CPS2 ½”NPT Steel Pigtail, Schedule 80 1000PSI 850˚F

CPSS4 ¼”NPT Stainless Steel Pigtail, Schedule 80 2000PSI 1000˚F CPSS2 ½”NPT Stainless Steel Pigtail, Schedule 80 2000PSI 1000˚F

ANGLE

STRAIGHT

TEST PORT PLUGS

Piping System Test Plugs These test ports are designed for permanent installation into piping system for quick access during maintenance checks. With gauge adapters for pressure tests or pocket thermometer insertion without shutting down or draining the system. Available with Nordel or Neoprene Cores, Brass or Stainless Steel bodies in 1/8”NPT through 1/2”NPT

Model Number

Nominal Size (in)

OAL (in) Material Pressure/

Temperature

Lower Connection

(in)

Body Hex (in)

CapHex (in)

Core Material

PLUG-1/8 1/8 NPT 1-1/4 Brass 200F/1000PSI 1/8 NPT 13/16 9/16 Neoprene PLUG-1/4 1/4 NPT 1-1/2 Brass 200F/1000PSI 1/4 NPT 1-1/16 1-1/2 Neoprene PLUG-3/8 3/8 NPT 1-1/2 Brass 200F/1000PSI 3/8 NPT 1-1/16 1-1/2 Neoprene PLUG-1/2 1/2 NPT 1-1/2 Brass 200F/1000PSI 1/2 NPT 1-1/16 1-1/2 Neoprene

PLUG-1/4SS 1/4 NPT 1-1/2 SS 304 200F/1000PSI 1/4 NPT 1-1/16 1-1/2 Neoprene PLUG-1/2SS 1/2 NPT 1-1/2 SS 304 200F/1000PSI 1/2 NPT 1-1/16 1-1/2 Neoprene

Pressure & Temperature Test Plugs Acessories PCR Plastic Cap Retainer - Available for all test plugs ADAPTER-PP-1/4 1/4" Gauge Adaptor 2-3/4" OAL x 1-3/4" x 0.063" probe ADAPTER-PP-1/2 1/2" Gauge Adaptor 2-3/4" OAL x 1-3/4" x 0.125" probe PG Probe guard for all gauge adapters

FILTER TYPE PRESSURE SNUBBER

Pressure oscillations and other sudden pressure changes can affect the delicate mechanisms of a pressure gauge or pressure transmitter. This can result in either complete failure of the instrument or false and inaccurate readings. Pressure snubbers are designed to reduce or prevent these oscillations and fluctuations from reaching and affecting pressure instruments. Pressure snubbers reduce pressure spikes only; a pressure snubber will not eliminate any prolonged overpressure. Spikes last for milliseconds only, over pressures lasting longer than that can damage the pressure sensor. The pressure snubbers below are the “filter” type using a porous filter media made of sintered metal. Because the filter element is a fine mesh type, it should be used on processes that do not contain particulate or sludge that would clog the element. In the event that the snubber does get clogged, our snubbers can be disassembled for cleaning if necessary. SPECIFICATIONS:

• Connection Sizes: 1/4" or 1/2"NPT • Stainless Steel or Brass • Water, Air, Oil or Gas • No Moving Parts – Nothing to break or wear out • Pressure Rating:

Brass: 3,000 PSI Stainless Steel: 10,000 PSI

Snubber Body Brass or 316 SS

Retaining Screw Brass or 316 SS Snubber Element Brass or 316 SS

Gauge Connection ½” or ¼” NPT Female

Process Connection ½” or ¼” NPT Male A (Inches) B (Inches) A (MM) B (MM) 1/4"NPT .75” 1.38” 18.9mm 35mm

1/2"NPT 1.13” 1.73” 28.5mm 44mm

Other Instrument protection accessories:

Piston Type Snubber Adjustable Snubber Needle Valve Pressure Limiting Valve

ADJUSTABLE PRESSURE SNUBBER

SNUBBER • Fully field adjustable • In stock for immediate delivery • Choice of Brass or Stainless Steel

FEATURES AND BENEFITS • Pressure Pulsation Dampener • Adjustable Dampening • Protects pressure gauges against pressure spikes, surges, and fluid hammers. • Can isolate the gauge for service or replacement. • Available in both Stainless Steel and Brass in 1/4", 3/8", and 1/2" NPT connection sizes. • Fine thread adjustable valve allows user to fine tune harmful harmonic vibration from fluid

systems • Precision ball affords shock protection during pressure spikes or fluid hammer conditions. • Most economical "life insurance" for instrumentation reliability. • Simple, Clever, Economical

Part No. Body Material "A" Thd. Size "B" "C" "D" Hex Maximum

Pressure MSB4 MSS4

Brass SS

1/4-18NPT 1/4-18NPT

.51 (13mm)

.51 (13mm) 1.77 (45mm) 1.77 (45mm)

.67 (17mm)

.67 (17mm) 3,000 PSI 5,000 PSI

MSB6 MSS6

Brass SS

3/8-18NPT 3/8-18NPT

.59 (16mm)

.59 (16 mm 2.36 (60 mm) 2.36 (60 mm)

1.18 (30mm)1.18 (30mm)

5,000 PSI 10,000 PSI

MSB8 MSS8

Brass SS

1/2-1/4-NPT 1/2-14--NPT

.79 (20mm)

.79 (20mm) 2.36 (60mm) 2.36 (60mm)

1.18 (30mm)1.18 (30mm)

5,000 PSI 10,000 PSI

PISTON TYPE PRESSURE SNUBBER

While each model is built to exacting specifications with tolerances to ten-thousandths of an inch, the unit-to-unit uniformity and easy piston changing makes installing a piston type Snubber into your system a smart choice.

Center Body Snubbers

MODEL 010 CONNECTIONS

MODEL NO. INLET OUTLET

BODY MATERIAL MAX PSI LN. HEX

010B Brass 3000 010S 303 Stainless 5000

010SS 1/4 NPT 1/4 NPT

316 Stainless 5000 3.46 .750

Available in British Taper Pipe Threads. Add BSP to part number when ordering.



BODY MTRL MAX PSI LN. HEX

050B 3/8 NPT 3/8 NPT Brass 5000 3.61 1.125 Available in British Taper Pipe Threads. Add BSP to part number when ordering.



BODY MTRL MAX PSI LN. HEX

060B Brass 5000 060S 303 Stainless 10000

060SS 1/2 NPT 1/2 NPT

316 Stainless 10000 3.61 1.125

Available in British Taper Pipe Threads. Add BSP to part number when ordering.

COOLING TOWER

Temperature Affects Pressure Gauges: Mechanical pressure gauges are typically designed and calibrated to be most

accurate and durable in ambient conditions between 65 and 85˚F, with process temperatures not exceeding 150˚F. If required, gauges can be ordered - calibrated to be most accurate for specific temperature ranges (within certain limits)

Outside of the normal working conditions temperature can affect the accuracy and lifespan of gauges. Precautions should be taken to ensure that pressure gauges are not continuously exposed to temperature extremes.

Good gauge practices have always recommended pigtail siphons (a) for steam or other high temperature applications. Other optional preventative measures include capillary (b) to remote mount the gauge away from the process or cooling towers to dissipate heat from the process fluid before it enters the gauge. This can also be true for low temperature extremes such as cryogenic applications.

Other methods for protecting instruments from temperature extremes:

(a) Pigtail Siphon ( b) Capillary

PRESSURE LIMITING VALVE

ADVANTAGES :

• PREVENT DAMAGE TO GAUGE / INSTRUMENTS DUE TO SUDDEN PRESSURE SURGE • 316SS CONSTRUCTION • COMPACT DESIGN • AUTOMATIC POSITIVE ACTION • IN LINE INSTALLATION • REPEATABLE PEFORMANCE • MAXIMUM WORKING PRESSURE 6,000 PSI

Part Numbering System PLV = PRESSURE LIMITING VALVE 4 = ¼” NPT 2 = ½” NPT M = MALE NPT THREAD F = FEMALE NPT THREAD RANGE = SEE BELOW Example: PLV-2F-2F- 1 SET: 80PSI

TECHNICAL FEATURES:

PIC Pressure Limiting Valves are also called over-load protectors or gauge savers. The PLV cuts off pressure rising above the desired pressure value (pre-set value) thus preventing failure of pressure gauge or instruments and also stops possible damages such as hazardous leakages and explosions etc.

The Pressure Limiting Valve or gauge saver shuts off the system with quick and positive action of built in push-rod device. As and when, the pressure falls below the pre-set pressure value, the line and/or the pressure gauge will be automatically put into operation again.

The PLV is of extreme importance and necessity for the protection of the pressure sensitive instruments against over pressures, sudden line induced pressure surges which are principal causes of the instrument and subsequent system failure. The PLV can be supplied to function at different cut-off pressure values on special request. The repeat accuracy of the unit depends on the rate of pressure rise. However, an accuracy of ± 10% of the set pressure may be expected.

Available Configurations Available Ranges

PLV ½” male ½” male 6,000 PSI PLV ½” male ½” female 6,000 PSI PLV ½” female ½” female 6,000 PSI PLV ¼” female ¼” female 6,000 PSI PLV ¼” male ¼” male 6,000 PSI PLV ¼” male ¼” female 6,000 PSI

RANGE Adjustment Span in PSI 1 50 to 120 PSI 2 80 to 180 PSI 3 150 to 300 PSI 4 250 to 600 PSI 5 700 to 1000 PSI 6 1200 to 1800 PSI 7 2000 to 3000 PSI 8 3000 to 6000 PSI

NEEDLE VALVES

¼”NPT “NVS” SUPER–MINI VALVES

¼”NPT Carbon Steel Body, Round ‘Thumb Wheel’ Handle 6,000 PSI Rated Soft Seat, for bubble tight shut-off Male x Female, Female x Female or Male x Male

¼”NPT “NV” Mini Valves

Carbon Steel or Stainless Steel Body, Tee Handle 6,000 PSI Soft Seat or 10,000 PSI Hard Seat Male x Female, Female x Female or Male x Male

¼”NPT ‘NVL’ or ½”NPT ‘NV’ Full Size Needle Valves

Carbon Steel or Stainless Steel Body, Tee Handle 6,000 PSI Soft Seat or 10,000 PSI Hard Seat Male x Female or Female x Female

¼” or ½”NPT Hex Body Needle Valves

Carbon Steel or Stainless Steel Body, Tee Handle 6,000 PSI Soft Seat or 10,000 PSI Hard Seat Male x Female or Female x Female

½”NPT Multi-Port Gauge Valves

Stainless Steel Body, Tee Handle 6,000 PSI Soft Seat or 10,000 PSI Hard Seat ½”NPT Male inlet x (3) ½”NPT Female Outlet

¼” or ½”NPT Block and Bleed Valves

Stainless Steel Body, Tee Handle 6,000 PSI Soft Seat or 10,000 PSI Hard Seat ¼”NPT or ½”NPT Male inlet x Female

½”NPT Long Body Valves

Stainless Steel Body, Tee Handle 6,000 PSI Soft Seat ½”NPT Male x Female

½”NPT Accessory Bleed Valves

Stainless Steel Body, Tee Handle Use with Multiport Gauge valves to make block and bleed Valves 6,000 PSI or 10,000 PSI

PROCESS NEEDLE VALVES Our high quality instrumentation grade needle valves are designed for heavy-duty process applications or other industrial applications that require high-pressure carbon steel or stainless steel shut-off valves. Our valves are available hard seat (10,000 psi) or soft seat (6,000 psi), ¼” or ½”npt, straight or angle pattern, male x male, female x female or male x female.

NVS NV (¼”NPT) NV (½”NPT) & NVL (¼”NPT) HV GV

Super Mini Mini Full Size Hex Body Multi-Port

Inch mm Inch mm Inch mm Inch mm Inch mm

A 1.02” 26mm A 1.81” 46mm A 2.67” 68mm A 3.65” 93mm A 3.68” 93mm B .32” 8 mm B .50” 13mm B 2.64” 67mm B 3.23” 82mm B 4.46” 113mm

C1 .40” 10mm C .17” 4 mm C 1.12” 29mm C 1.26” 32mm C 1.26” 32mm C2 .20” 6 mm D .44” 11mm D .73” 19mm D 1.65” 42mm D 1.61” 41mm D .46” 12mm E .34” 9 mm E 2.25” 57mm E .75” 19mm E .82” 21mm E .75” 19mm F .75” 19mm F 2.25” 57mm F 2.25” 57mm F .52” 13mm G .61” 15mm G 1.31” 33mm H 1.04” 26mm

Part Number System:

DIAPHRAGM SEALS

Diaphragm Seals are designed for use in applications where chemical compatibility, trash or sludge in process or sanitary requirements prevent the use of a standard pressure gauge or gauge only installation. Diaphragm Seals consist mainly of an upper housing, lower housing and a separating diaphragm. These components can be selected and made of different type materials for better compatibility with the end process. Diaphragm seal assemblies can be made and selected with different types of Pressure instruments, instrument connections, process connections or types of seals. It is important to know as much about the application as possible so that the correct specifications are used when selecting the diaphragm seal assembly.

Below you will find some of the information you will need to know to properly select a diaphragm seal assembly.

PIC stocks, fills and calibrates complete diaphragm seal assemblies. We can supply materials of construction, connection types and sizes, and fill fluids suitable for almost any application you run into! We can typically assemble, fill and test standard gauges and diaphragm seal assemblies from our stock in 1-2 days. Please call with your inquiry.

When specifying, ordering or requesting quotes for diaphragm seals – Be ready to answer the following questions;

ABOUT THE APPLICATION What type of instrument is required? (Pressure Gauge, Transmitter or Transducer, Pressure Switch or other) What is the process in contact with the seal? What else is important for this application?

ABOUT THE DIAPHRAGM SEAL What materials of construction are required for;

Upper Housing? Diaphragm? (Wetted Parts A) Lower Housing? (Wetted Parts B) Gaskets or O-rings (If applicable)? Bolting or Plugs (If applicable)?

What type of connections is required for; Instrument Connection? Process Connection? Flushing Connection (If applicable)?

What size (and rating) connections are required? Are there any special requirements for this application? (Flushing Connection, Clean-out Ring, All Welded Design, Sanitary or Special Cleaning, Capillary System or Other)

ABOUT THE FILL FLUID What fluid is compatible with your process? (Fill Fluid needs to be compatible with process as a safety concern in case the diaphragm ruptures) What Special Conditions will the fill fluid be subjected to? (High Temperatures, Low Temperatures, Wide Range of Temperatures, Long Capillary Lengths, Etc.)

DIAPHRAGM SEALS (continued)

DS- - - Model Number: Flushing Connections M35 M3500 SERIES 0 = No Flushing Connection

M45 M4500 SERIES F = with Flushing Connection HP = High Pressure Seal

Instrument Connection Material of Const. 1 = ¼” FNPT 316 = 316SS

2 = ½” FNPT Process Connection HTC = Hastalloy ‘C’ 1 = ¼” FNPT MNL = Monel 2 = ½” FNPT TAN = Tantalum 3 = ¾” FNPT

4 = 1” FNPT

Product: Flushing Connection DS = Diaphragm Seal F = Flushing Connection Upper Housing: Seal / Connection Rating S = Carbon Steel A = 2000 PSI J = Stainless Steel B = 5000 PSI I = 2500 PSI Instrument Connection: E = 150 # (Flange) 1 = ¼”FNPT F = 300 # (Flange) 2 = ½”FNPT Process Connection Size Diaphragm Material: 1 = ¼” Lower Housing Material: 2 = ½” S = Carbon Steel 3 = ¾” G = 304 Stainless Steel 4 = 1” J = 316 Stainless Steel K = Tantalum Connection Type M = Monel T = Threaded T = Teflon F = Flanged X = Other S = Sanitary

Mini Diaphragm Seals: All welded design, Standard pressure rating: 2000 PSI (5000 PSI rated available). Female threaded standard (Male process connection theaded available)

M3500 SERIES M4500 SERIES 1 ½”Dial through 3 ½”Dial sizes All Gauges through 4 ½” Dial Size Pressure transducers and transmitters Pressure Transducers and Transmitters or other small displacement instruments. Most Pressure Switches or other small to medium displacement instruments

DS-M35xx DS-M35xx DS-M45xx DS-M45xx

Large Volume Diaphragm Seals

FLUSHING CONNECTION FLUSHING

CONNECTION

DIAPHRAGM SEALS

Precision Instrument Company is a full line Diaphragm Seal Manufacturer. We Manufacture all sizes, connections and materials, Stocking the most commonly used types. We also attach instruments and

Fill Systems giving us many options with quick deliveries.

MINI SEALS Medium Seals Low Pressure FULL SIZE Best low cost for small

instruments Best low cost for medium

to large instruments

Large area diaphragm for low pressures and Vacuum

Applications

Most versatile for all applications

Flanged Connection Tri-Clamp Sanitary Flow Through Saddle Mount Raised Face or Flat Face

Pressure from 150# to 2500# Food and

Pharmaceutical Designed for Easy

Cleaning

Tri-Clamp, Flanged or Threaded Straight Through flow designs eliminate dead zones in piping

Weld-in Saddle Mount

Special Seals Components & Accessories Filling / Calibrating Male NPT – Plug Type, Flush

Diaphragm, Button Type or other custom designs

Upper & Lower Housings, Diaphragms, Gaskets or O-Rings, Bolting, etc.

SS armored Capillary Made to Length with connections matching gauges & seals

Using any fill fluid suitable for the application.

(See separate page for available fills)

MINI DIAPHRAGM SEALS

All welded design, Standard pressure rating: 2000 PSI (5000 PSI rated available).

Female threaded standard (Male process connection theaded available)

M3500 SERIES 1 ½”Dial through 3 ½”Dial sizes

Pressure transducers and transmitters or other small displacement instruments. For Pressures 60 psi Through 2500 PSI

M4500 SERIES All Gauges through 4 ½” Dial Size

Pressure Transducers and Transmitters Most Pressure Switches

or other small to medium displacement instruments 30 PSI Through 2500 PSI

M3500-LP SERIES 1 ½”Dial through 3 ½”Dial sizes

Pressure transducers and transmitters or other small displacement instruments. For Vacuum or Pressures up to 2500 PSI

DS-M35 DS-M45 DS-M35 (LP)

Model Numbers:

DS- - - Model Number: Flushing Connection M35 M3500 SERIES 0 = No Flushing Connection M45 M4500 SERIES Material of Const. F = with Flushing Connection

316 = 316SS HP = High Pressure Seal Instrument Connection Process Connection HTC = Hastalloy ‘C’ LP = Low Pressure Seal 1 = ¼” FNPT 1 = ¼” FNPT MNL = Monel 2 = ½” FNPT 2 = ½” FNPT TAN = Tantalum 3 = ¾” FNPT 4 = 1” FNPT Standard Fills (Others available by request): Fill Temp Range Fill Temp Range Pure Glycerine (Food Grade) +30 to + 300˚F Mineral Oil Information TBA Silicone DC200-1000cs - 35 to + 450˚F Fluorolube FS-5 - 40 to + 500˚F Silicone DC 550 - 40 to + 600˚F Halocarbon Oil 6.3 - 40 to + 400˚F Ethylene Glycol (Anti-Freeze) - 30 to + 300˚F Syltherm 800 - 40 to + 450˚F

THREADED DIAPHRAGM SEALS

General Specifications

Diaphragm welded to upper housing housings available w/replaceable diaphragm gasketed between upper & lower housings Instrument Connection: ¼” or ½”NPT (Others available) Process Connection” ¼”, ½”, ¾” or 1” NPT (Others Available) Chrome Plated Carbon Steel or Stainless Steel Upper Housing Grade 8 Galvanized Steel or Stainless Steel Bolts Standard Pressure Rating = 2500 psi High Pressure model = 10,000 psi

Optional Wetted Materials

Chrome Plated Carbon Steel 316SS, 304SS, 316L-SS, 304L-SS Hastelloy C276, B2 Inconel 600, 625 Tantalum (Diaphragm Only) Nickel Monel 400 Titanium Carpenter 20 Teflon PVC Kynar Others upon Request

Gaskets

Buna N Viton Teflon Grafoil Others upon Request

Product: Flushing Connection DS = Diaphragm Seal F = Flushing Connection Upper Housing: Seal / Connection Rating S = Carbon Steel A = 2000 PSI (Clamped Diaph.) J = Stainless Steel B = 5000 PSI I = 2500 PSI (Welded Diaph.) Instrument Connection: E = 150 # (Flange) 1 = ¼”FNPT F = 300 # (Flange) 2 = ½”FNPT Process Connection Size Diaphragm Material: 1 = ¼” Lower Housing Material: 2 = ½” S = Carbon Steel 3 = ¾” G = 304 Stainless Steel 4 = 1” J = 316 Stainless Steel K = Tantalum Connection Type M = Monel T = Threaded T = Teflon F = Flanged X = Other S = Sanitary I = Inline Welded W = Saddle Weld

Part Number System

Standard Threaded Threaded with Flush Threaded

w/Clean-out Ring Threaded

High Pressure

FLANGED DIAPHRAGM SEALS

General:

• Standard: Clamped Type Diaphragm with Upper & Lower Housing Gaskets Option: Available with Diaphragm Welded to Upper Housing (Note: Model Number changes to ‘200’) *

• Instrument Connection: ¼” or ½”NPT * • Process Connection: ½”, ¾”, 1” 1 ½” RF Flanged * • Pressure Rating: per ANSI B16.5 - 150 # or 300 # Standard * • Upper Housing: Chrome Plated Carbon Steel Standard – Stainless Steel Available * • Bolting: Grade 8 Galvanized Steel Standard – Stainless Steel Available * • RTJ Connection Also Available

* (Others Available upon Request) Wetted Materials Available(Includes Diaphragm and Lower Housing): 316 SS, 304 SS, 316L SS, 304L SS, Hastelloy C276, B2, Inconel 600, 625, Tantalum (Diaphragm Only), Nickel, Monel 40, Titanium, Carpenter 20, Teflon, PVC, Kynar, Others upon Request Gasket Materials: Buna N, Viton, Teflon, Grafoil, Others upon request Fill Fluids Available: Glycerine (standard), Silicone (various Grades and viscosities), Glycol, Halocarbon, Slytherm, Others Upon Request

100-FL-1

Process Connection A B

½” 3 ½” 1 3/8”

¾”

150 #

3 ¾” 1 11/16”

½” 3 ¾” 1 3/8”

¾”

300 #

4 5/8” 1 11/16”

½” or ¾” Flanged Off Line

100-FL-2 Process Connection A B

1” 150 # 4 ¼” 1 3/8”

1” 300 # 4 7/8” 1 9/16” 1” Flanged Off Line

100-FL-3 Process Connection A B

All Dimensions According to Size and Rating.

1 ½” or Larger Flanged Off Line

‘DS-M3A’ TRI-CLAMP SANITARY DIAPHRAGM SEALS

Part Number System: Model # Special Options DS-M3A Sanitary Tri-Clamp Diaphragm Seal Specifiy Uncoded Options

Instrument Connection Tri-Clamp Size 1 = 1/4" NPT 2 = ½”Tri-Clamp 2 = 1/2" NPT 3 = ¾”Tri-Clamp 4 = 1”Tri-Clamp 6 = 1 ½”Tri-Clamp 8 = 2”Tri-Clamp

½” and ¾” Tri-Clamp 1”, 1 ½” and 2” Tri-Clamp

A B C D E F G H Inches 1.12” 1.48” .99” .93” .30” .24” .54” ½” mm 28.4 37.7 25 23.8 7.73 6.11 13.8 Inches 1.12” 1.48” 1.13” .93” .34” .19” .75” ¾” mm 28.4 37.7 28.7 23.8 8.86 4.85 19.25 Inches 1” mm Inches 1.27” 1.68” 1.98” 1.09” .18” 1.55” 1 ½” mm 32.3 42.55 50.5 27.7 4.6 39.42 Inches 1.29” 1.93” 2.49” 1.10” .25” 1.79” 2” mm 32.8 48.95 63.44 28.1 6.34 45.5

NOTES:

1. The Series ‘DS-M3A’ are designed for Gauges Dial Sizes 1.5” and larger and are also acceptable for pressure transducer/transmitters or other small displacement instruments.

2. Standard Material of Construction: All 316 Stainless Steel (Others Available). 3. Pressure Rating is based on the clamp and gasket used with the assembly. 4. Specify thread size for instrument and Clamp Size for process connection.

Diaphragm seals are designed for use in applications where sanitary conditions and cleanliness, trash or sludge in process prevent the use of a threaded pressure gauge or diaphragm seal installation. These seals are designed for quick removal, cleaning and re-installation without the use of tools. These diaphragm seals consist mainly of an upper housing, and a separating diaphragm. This type of seal is available in 316ss in sizes from ½” through 2” tri-clamp connections. diaphragm seal assemblies can be mated with different types of pressure instruments. Due to the type of clamp used pressure ratings are limited so it is important to know as much about the application as possible so that the correct specifications are used when selecting the diaphragm seal assembly.

DS-M3A XX

TRI-CLAMP SANITARY GAUGE

Dial: 2 ½” or 4” Diameter Case: Stainless Steel Hermetically sealed & Liquid Fillable Standard Lens: Laminated Safety Glass Pointer: Micrometer Adjustable Bourdon Tube: AISI 316 Stainless Steel Socket: AISI 316 Stainless Accuracy: 4” Dial = 0.5 % Full Scale 2 ½”Dial = 1.0 % Full Scale Movement: Heavy Duty 300 series SS STANDARD FEATURES • Overload and Underload Stops • Laminated Safety Glass Lens • Hermetically Sealed/Weather Proof • Liquid Fillable Out of The Box / No Kit Required

• Original Product • Best Product • Best Value PART NUMBERING SYSTEM:

Code Range A 30”Hg-0

CB 30”Hg-0-15 psi CC 30”Hg-0-30 psi CD 30”Hg-0-60 psi CE 30”Hg-0-100 psi CF 30”Hg-0-150 psi CH 30”Hg-0-300 psi B 0-15 C 0-30 D 0-60 E 0-100 F 0-160 G 0-200 H 0-300

43A1 15LD E

RANGE CODE

OPTIONS

GAUGE: 43A1 = 4”DIAL 23A1 = 2 ½”Dial SS Case, 316SS Internals

43A1

34 = ¾”Triclamp Connection 15 = 1 ½”Tri-Clamp Connection 20 = 2” Tri-Clmap Connection 25 = 2 ½” Tri-Clamp Connection

L = Bottom Connection R = Back Connection

D = Dry Gauge, No Fill L = Glycerine Filled

These gauges have been designed to meet 3A requirements for the dairy and food processing industries.

Currently we do not have 3A certification for our standard stock products.

If 3A certification or stamp is required for your application, please specify that you require 3A rating when requesting your quote. These gauges conform to ANSI B40.1

701LDS MOLDED GAUGE/SEAL This innovative new product was developed to solve many common problems associated with polymer type diaphragms seals. Due to the all molded design the gauge cannot be removed from the seal, preventing loss of fill – And There is no chance of cracking the upper housing by over tightening the gauge. This product is also molded of a harder blend of polymers – making them more resistant to cracking or breaking during installation.

Black Body PP Assembly White Body PTFE Assembly

For filter and pump control on liquid and

gases. Housed in all PP material can resist

transient overpressure and maintain leak-tight connection. It is also designed to satisfy

requirements in corrosive atmosphere & fluids.

TEFLON anti-impact, all in one Protect from acidification & alkalization excellent stability With its deform temperature is 150℃. Specialized used in PCB/LCD, high-tech zone, IC equipment, pipe-Line installation and the internal outfit of dust-free chamber with all in one case cover-ed around in order to its unbreakable function and excellent anti-corrosion properties.

Polypropylene Seal Assembly Specifications: PTFE Seal Assembly Injection Molded Polypropylene Case & Body: Injection Molded PTFE

2 ½” Diameter Dial Size: 2 ½” Diameter 1/4" or ½” FNPT Process Conn: 1/4" or ½” FNPT

Viton Diaphragm: PTFE Brass Bourdon Tube: 316SS Brass Internals: 316SS

Glycerine (Others Available upon Request) Fill Fluid: Based upon customer requirements Polycarbonate Lens: Polycarbonate

Dry but Fillable Case Style: Dry but Fillable Dual Scale PSI / Bar / x 100 = kPa

Others Available upon Request Dial: Dual Scale PSI / Bar / x 100 = kPa Others Available upon Request

15 PSI to 400 PSI Max Pressure: 15 PSI to 400 PSI -4’F to 140’F / -20’C to + 60’C Max Temp: -4’F to 140’F / -20’C to + 60’C

1.5 % Full Scale Accuracy: 1.5 % Full Scale

Dimensions: Inches MM

A 2.89” 73.44 B .62” 15.80 C 1.04” 26.47 D 2.61” 66.36 E .50” 12.82 F 1.19” 30.36 G .43” 10.99 H 1.23” 31.28 I 2.29” 58.29

FILL FLUIDS FOR GAUGES & SEALS

% Glycerine/Water Mix 90/10 = 29.1˚F 80/20 = -4.5˚F 70/30 = -38˚F

60/40 = -30.5˚F 50/50 = -9.4˚F 40/60 = 4.3˚F 30/70 = 14.9˚F 20/80 = 23.4˚F

Glycerine 99.5 % (Food Grade) Standard fill unless otherwise specified

+30 to +300˚F 99.5 % Glycerine is standard, but glycerine can be mixed with water to obtain different temperature ratings (see table to right)

10/90 = 29.1˚F Viscosity

5 cSt. = -120˚F 20 cSt. =-85˚F

100 cSt. = -67˚F 200 cSt. = -61˚F

1000 cSt. = -58˚F 10,000 cSt. = -53˚F

Silicone fluid Most common alternate to glycerine In stock DC-200 1000 cSt.

-50 to +450˚F 1000 cSt silicone fluid is standard, but silicone fluid can be ordered in different viscosities to obtain different temperature ratings and dampening effects (see table to right)

60,000 cSt. = -47˚F

Mineral Oil 0.88 270 cP -30 to +200˚F

Instrument Oil (Note 2)

Propylene Glycol (pharmaceutical-USP)

1.03 42.6 -50 to +200˚F

Halocarbon oil® (see note 1)

1.87 6.3 -40 to +400˚F

Fluorolube FS-5® (see note 1)

1.87 5.5 -40 to +500˚F

Syltherm 800®

0.93 10.7 -40 to +450˚F

Neobee M-20® (Food Grade)

0.92 9.5 cP -4 to +320˚F

Ethylene Glycol (Anti-Freeze)

1.10 30e -30 to +300˚F

Fill fluids should be selected carefully considering their physical properties at the extremes of the ambient and process temperature to which they will be subjected. Fill fluids must also be chemically compatible with the process fluid to avoid potentially hazardous reaction in the event of a bourdon tube or diaphragm failure. Typically, hydrocarbon based fluids must not be used with strong oxidizers such as oxygen, chlorine, hydrogen peroxide or nitric acid. For these special applications, inert liquids such as Fluorolube® or Halocarbon® are available. Diaphragm seal fills should not be diluted with or contain water. The presences of water in filled systems can cause gross inaccuracies. Notes:

1. Not to be used in contact with aluminum or magnesium. 2. Information to be advised

QUALITY THERMOMETERS

BI-METAL THERMOMETERS Bi-Metals in 1”, 2”, 3” & 5” Dial Sizes

Back Connection, Adjust-Angle or Bottom Connection All Stainless Construction, Vibration Resistant - No Needle Flutter

Fast Response To Temperature Change, Hermetically Sealed (Moisture Proof) Anti-Parallax Dial (Easy To Read), Recalibratable

A Complete Variety of Stem Lengths & Temperature Ranges Available

OTHER INDUSTRIAL QUALITY THERMOMETERS We also carry a variety of other types of thermometers including (But not limited to):

Remote Thermometers, Scale Type - Red-Reading - Glass Tube Thermometers, Magnetic Thermometers and Pocket thermometers.

We Have A Thermometer For Your Application

2”DIAL BIMETAL THERMOMETERS

90° BACK ANGLE TYPE

A B C D E 2” IN. 2” STEM LENGTH .24” .60” .95”

Dial MM 50.79 STEM LENGTH 6.21 15.24 24.03

STEM LENGTH*

PART NUMBER

2” DIAL 2 ½” B2B2 4” B2B4 6” B2B6 9” B2B9 12” B2B12

STANDARD RANGES* CODE RANGE

AA -40/120˚F & C BB -40/160˚F & C EE 0/150˚F & C GG 0/200˚F & C HH 0/220˚F&C JJ 20/240˚F & C II 0/250˚F & C

MM 50/300˚F & C PP 50/400˚F & C RR 50/550˚F & C SS 150/750˚F & C TT 200/1000˚F & C

*Note: • Other Ranges, Stem Lengths And Configurations

Are Available Upon Request. • Thermowells of all sizes and materials of

construction are available also. • Please Call With Any Inquiries.

STANDARD FEATURES • All Stainless Construction • With Glass Lens • Fast Response To Temperature Change • Hermetically Sealed (Moisture Proof) • +/- 1 % Full Scale Accuracy • 316SS Stem Material • Stem Welded To Connection

3”or 5” DIAL BIMETAL THERMOMETERS


STEM LENGTH*

PART NUMBER

3” DIAL 5” DIAL 2 ½” B3B2 B5B2 4” B3B4 B5B4 6” B3B6 B5B6 9” B3B9 B5B9 12” B3B12 B5B12 15” B3B15 B5B15 18” B3B18 B5B18 24” B3B24 B5B24

A B C D E 3” IN. 3.18” STEM LENGTH .25” .60” .38”

Dial MM 80.78 STEM LENGTH 6.45 15.24 9.76 5” IN. 5.13” STEM LENGTH .25” .67” .38”



AA -40/120˚F & C BB -40/160˚F & C EE 0/150˚F & C GG 0/200˚F & C JJ 20/240˚F & C II 0/250˚F & C


*Note: • Other ranges, stem lengths and configurations are

available upon request. • Thermowells of all sizes and materials of construction

are available also. • Please call with any inquiries.

STANDARD FEATURES • All Stainless Construction • With Glass Lens • Anti-Parallax Dial • Vibration Resistant (Reduced Needle Flutter) • Fast Response To Temperature Change • Hermetically Sealed (Moisture Proof) • +/- 1 % Full Scale Accuracy • 316SS Stem Material • Stem Welded To Connection • Zero Adjustment on Back of Case

ADJUSTABLE ANGLE BIMETAL THERMOMETERS


AA -40/120˚F & C BB -40/160˚F & C EE 0/150˚F & C GG 0/200˚F & C JJ 20/240˚F & C II 0/250˚F & C


PART NUMBER*

STEM LENGTH*

B5A2 2 ½” B5A4 4” B5A6 6” B5A9 9”

B5A12 12” B5A15 15” B5A18 18” B5A24 24”

* For 3” Dial Size change ‘B5A’ to ‘B3A’

Dial A B C D E IN. 5.13” STEM LENGTH ¼” .67” 3.3” 5” MM 130.39 STEM LENGTH 6.45 16.95 83.87 IN. 3.13” STEM LENGTH ¼” .67” 3.3” 3” MM 78 STEM LENGTH 6.45 16.95 83.87

STANDARD FEATURES • All Stainless Construction • Adjustment Screw on Case • Glass Lens • Anti-Parallax Dial • Vibration Resistant (Reduced Needle Flutter) • Fast Response To Temperature Change • Hermetically Sealed (Moisture Proof) • +/- 1 % Full Scale Accuracy • 316 SS Stem • Stem Welded at ½”NPT Hub

*NOTE: 1.) Other ranges, stem lengths and configurations are

available upon request. 2.) Thermowells of all types and materials of construction

available also 3.) Please call with any inquiries.

MISCELLANEOUS BIMETALS

B2Bx 2”Dial Size Bimetal Thermometers ¼”diameter, ¼”NPT threaded stem Plastic Lens All Stainless Construction With re-calibration screw on back of case Accuracy: +/- 1 scale division Available ranges: -40/160˚F&C, 25/125˚F, 0/220˚F&C, 50/300˚F&C, 50/500˚F&C Available stem lengths: 2 ½”, 4” & 6” (others available upon request)

BxB5 1”Dial Size Pocket Thermometers Magnifying Plastic Lens 1/8” Diameter Pointed Plain Stem (Non-Threaded) With Plastic Sleeve / Pocket Clip Case Stainless Construction With re-Calibration Feature Accuracy: +/- 1˚Scale Division Available ranges: -40/160˚F, 25/125˚F&C, 0/220˚F&C (or ˚F only), 50/550˚F&C (or ˚F only) Ranges for 2”Dial Size: -40/160˚F&C, 0-220˚F&C (others available upon request) Stem Lengths: 5” (others available upon request)

B2Bx-x-CLIP 2”Dial Size Clip Type Thermometers Plastic Lens 1/8” Diameter Pointed Plain Stem (Non-Threaded) With Stainless Steel Clip Stainless Construction With re-calibration feature Accuracy: +/- 1 scale division Available range: 50/550˚F&C (others available upon request) Available stem lengths: 6”, 10” or 12” (others available upon request)

B2B1-K / B2B1-K-SW 2 ½”Dial Size Hot Water Thermometers Plain Stem for use with Snap on Well* *Wells Available: Brass - ½”NPT Threaded or Solder Type Plastic Lens Aluminum Construction Accuracy: +/- 1˚scale division Range: 30/240˚F&C Stem Length: 1 ½”

“BBQ-1” BAR-B-Q GRILL THERMOMETER


A B C D E 3” IN. 3.18” STEM LENGTH .25” .60” .38”


PART NUMBER

STEM LENGTH*

BBQ-1 2 ½”

STANDARD RANGE 50/550˚F & C

*Note: • Other Ranges, Stem Lengths And Configurations

Are Available Upon Request. • Thermowells of all sizes and materials of

construction are available also. • Please Call With Any Inquiries.

STANDARD FEATURES • All Stainless Construction • With Heavy Duty Glass Lens • Anti-Parallax Dial • Vibration Resistant (No Needle Flutter) • Fast Response To Temperature Change • Hermetically Sealed (Moisture Proof) • +/- 1 % Full Scale Accuracy • 316SS Stem Material • Stem Welded To Connection • Zero Adjustment on Back of Case

THERMOWELLS

Precision Instrument Company is a full line Thermowell Manufacturer. We Manufacture all sizes, connections and materials, Stocking the most commonly used types. We also make specials and carry accessories allowing for many options with quick deliveries.

Standard Wells Lagging Wells ANSI Flanged RTJ Flanged

Weld In Socket Weld Van Stone Test Port

Our capabilities include: Available Materials Available Connections Special Application

Brass Hastelloy C Threaded Clamped High Pressure Steel Titanium Flanged Sanitary High Velocity

Stainless Steel Tantalum Welded Van Stone Sanitary Monel Ceramic Test Port

Other materials and connections available upon request. Please contact us with your application.

THERMOWELLS

WELLS FOR INDUSTRIAL BIMETAL THERMOMETERS Standard Wells Wells with Lagging Extension

½”NPT x ½”NPT ½”NPT x ½”NPT

A U Brass Steel 304SS 316SS A U T Brass Steel 304SS 316SS 2 ½” 1 5/8” TW-BR02-22S TW-CS02-22S TW-ST02-22S TW-SS02-22S 2 ½” - 1 TW-BR02-22L TW-CS02-22L TW-ST02-22L TW-SS02-22L

4” 2 ½” TW-BR04-22S TW-CS04-22S TW-ST04-22S TW-SS04-22S 4” 1 5/8” 2 TW-BR04-22L TW-CS04-22L TW-ST04-22L TW-SS04-22L 6” 4 ½” TW-BR06-22S TW-CS06-22S TW-ST06-22S TW-SS06-22S 6” 2 ½” 3 TW-BR06-22L TW-CS06-22L TW-ST06-22L TW-SS06-22L 9” 7 ½” TW-BR09-22S TW-CS09-22S TW-ST09-22S TW-SS09-22S 9” 4 ½” 3 TW-BR09-22L TW-CS09-22L TW-ST09-22L TW-SS09-22L

12” 10 ½” TW-BR12-22S TW-CS12-22S TW-ST12-22S TW-SS12-22S 12” 7 ½” 3 TW-BR12-22L TW-CS12-22L TW-ST12-22L TW-SS12-22L

½”NPT x ¾”NPT ½”NPT x ¾”NPT



12” 10 ½” TW-BR12-23S TW-CS12-23S TW-ST12-23S TW-SS12-23S 12” 7 ½” 3 TW-BR12-23L TW-CS12-23L TW-ST12-23L TW-SS12-23L 15 13 ½” TW-BR15-23S TW-CS15-23S TW-ST15-23S TW-SS15-23S 15 10 ½” 3 TW-BR15-23L TW-CS15-23L TW-ST15-23L TW-SS15-23L 18 16 ½” TW-BR18-23S TW-CS18-23S TW-ST18-23S TW-SS18-23S 18 13 ½” 3 TW-BR18-23L TW-CS18-23L TW-ST18-23L TW-SS18-23L 24 22 ½” TW-BR24-23S TW-CS24-23S TW-ST24-23S TW-SS24-23S 24 19 ½” 3 TW-BR24-23L TW-CS24-23L TW-ST24-23L TW-SS24-23L

½”NPT x 1”NPT ½”NPT x 1”NPT



12” 10 ½” TW-BR12-24S TW-CS12-24S TW-ST12-24S TW-SS12-24S 12” 7 ½” 3 TW-BR12-24L TW-CS12-24L TW-ST12-24L TW-SS12-24L 15 13 ½” TW-BR15-24S TW-CS15-24S TW-ST15-24S TW-SS15-24S 15 10 ½” 3 TW-BR15-24L TW-CS15-24L TW-ST15-24L TW-SS15-24L 18 16 ½” TW-BR18-24S TW-CS18-24S TW-ST18-24S TW-SS18-24S 18 13 ½” 3 TW-BR18-24L TW-CS18-24L TW-ST18-24L TW-SS18-24L 24 22 ½” TW-BR24-24S TW-CS24-24S TW-ST24-24S TW-SS24-24S

24 19 ½” 3 TW-BR24-24L TW-CS24-24L TW-ST24-24L TW-SS24-24L

Brass Wells are not recommended for installations involving pressures and/or temperatures over 400’F Brass cap and Chain available to keep bore clean when not in use Other Wells available by request:

Materials Connection Types Special Application Hastelloy C ASA Flanged High Pressure

Titanium Van Stone High Velocity Tantelum Weld-in Sanitary

Teflon Coating Tri-Clamp Test Port

www.PICgauges.com (888) 650-6923 [email protected]

REMOTE DIAL THERMOMETERS

Offered in 2 ½”, 3 ½” and 4 ½” dial sizes, these thermometers are furnished in four stainless steel case configurations for direct, surface or panel mounting. The following coding chart illustrates a wide variety of bulb styles, capillaries and process connection fittings. The versatility of configurations makes these thermometers well suited to a wide range of applications including hot and chilled water pipeline systems, tanks and air ducts.

‘G45’ GAS ACTUATED THERMOMETERS

Precision Instrument Company gas actuated thermometers combine mechanical instrument technology with reliable gas filled capillary tube and bulb assembly. The thermometer transmits temperature readings via expansion of the inert Gas used inside the bulb through the capillary and displaying the temperature on a dial type indicator. The result is a remote reading thermometer that requires no external power allowing temperature indication where it is convenient for the user. SPECIFICATIONS ACCURACY ±1% of range span. DIAL - white coated aluminum with black markings. POINTER - slotted adjustable type permits "zero set" calibration. CAPILLARY - standard with stainless steel spiral interlock armor BULB – 6”Stainless Steel with ½”NPT Bushing SCALE – Linear dial arc (Due to Gas filled System)

Part Number System:

CUSTOM TRIDICATORS

Combination Pressure / Temperature Gauges

2 ½”, 3 ½” or 4”Dial Size ♦ Bottom or Back connected ♦ Plastic or Glass lens ♦ Black Steel, Chrome, Stainless Steel or Plastic Case ♦ Customer Specified Threaded Connections and Stem Lengths.

Check our standard items we keep in stock – or - we can manufacture custom logos, ranges and configurations.

2 ½” & 3 ½” Dial Sizes

2 ½”Dial TRIDICATORS

These instruments have been designed to indicate temperature and pressure in a single unit. With a price that makes this an affordable option for applications where bronze internals are suitable for use, the use of a single ‘tridicator’ saves time during installation, amount of piping required and of course saves money versus using separate gauges and thermometers. The primary applications for these are hot water boilers and water heaters.

General Specifications

• 2 ½”Dial, 1/4”NPT Center Back Connection • Available With 1/2"NPTAdapter • Black Steel Case and Bezel • Dual Reading Pressure & Temperature • Temperature: 70-320˚f & 20-160’c • Pressure: PSI & Feet of Water • Plastic Lens with Red Indicator • 3-2-3 % Accuracy

Dimensions A B C D E F Inches 2.64 1.02 .34 .53

Per Customers Requirements


Millimeters 67 26 9 13.5



PART NUMBER PRESSURE TEMPERATURE PSI Feet of Water ‘F ‘C TRI-RC-254Rx.xx-D 0/75 PSI 0-170’ 70-320˚F 20-160˚C TRI-RC-254Rx.xx-E 0/100 PSI 0-231’ 70-320˚F 20-160˚C TRI-RC-254Rx.xx-G 0/200 PSI 0-460’ 70-320˚F 20-160˚C TRI-RC-254Rx.xx-H 0/300 PSI 0-690’ 70-320˚F 20-160˚C

3 1/4"DIAL TRIDICATORS

These instruments have been designed to indicate temperature and pressure in a single unit. With a price that makes this an affordable option for applications where bronze internals are suitable for use, the use of a single ‘Tridicator’ saves time during installation, amount of piping required and of course saves money versus using separate gauges and thermometers. The primary applications for these are hot water boilers and water heaters. General Specifications

• 3 ¼”Dial, 1/4”Npt Center Back Connection • Available With 1/2"Npt Adapter • Black Steel Case and Bezel • Dual Reading Pressure & Temperature • Temperature: 70-320˚F & 20-160˚C • Pressure: 0-100 PSI & 0-700 kPa • Plastic Lens • 3-2-3 % Accuracy

Dimensions A B C D E F

Inches 3.20” 1.20” 1.96” 1.50” .37” .54”

Millimeters 84mm 30.7mm 50.7mm 38mm 9.5mm 13.7mm

PRESSURE TEMPERATURE PART NUMBER PSI kPa ˚F ˚C TRI-RC-3.25Rx.xx-D 0/60 PSI 0-400 kPa 70-320˚F 20-160˚C TRI-RC-3.25Rx.xx-E 0/100 PSI 0-700 kPa 70-320˚F 20-160˚C TRI-RC-3.25Rx.xx-G 0/200 PSI 0-1400 kPa 70-320˚F 20-160˚C TRI-RC-3.25Rx.xx-H 0/300 PSI 0-2100 kPa 70-320˚F 20-160˚C

INDUSTRIAL TRIDICATORS

These instruments have been designed to indicate temperature and pressure in a single unit. With a price that makes this an affordable option for applications where bronze internals are suitable for use, the use of a single ‘tridicator’ saves time during installation, amount of piping required and of course saves money versus using separate gauges and thermometers. The primary applications for this product are hot water boilers and water heaters.

STANDARD FEATURES • Painted Steel Case (For Rust And Corrosion Resistance) • Plastic Lens for Round Dial Tridicators Glass Lens for Square Dial Tridicators • +/- 1 % Full Scale Accuracy • Large Easy To Read Numbers • Dual Scale: PSI & kPa For Pressure ˚F & ˚C Temperature

A B C D ROUND DIAL TRIDICATORS INCHES 3.93” 1.41” .63” 2.00” MM 99.82 35.80 16 51 SQUARE DIAL TRIDICATORS INCHES 3.65” 1.51” .89” 2” MM 92.75 38.39 22.60 50.80

PART NUMBER PRESSURE TEMPERATURE CONN DIAL TRI-RC-352L-D 0/75 PSI 60-260˚F LOWER ROUND TRI-RC-352L-G 0/200 PSI 70-320˚F LOWER ROUND TRI-RC-352R-D 0/75 PSI 60-260˚F BACK ROUND TRI-RC-352R-G 0/200 PSI 70-320˚F BACK ROUND TRI-SQ-352L-D 0/75 PSI 60-260˚F LOWER SQUARE TRI-SQ-352L-E 0/100 PSI 60-260˚F LOWER SQUARE TRI-SQ-352L-G 0/200 PSI 80-320˚F LOWER SQUARE TRI-SQ-352R-D 0/75 PSI 60-260˚F BACK SQUARE TRI-SQ-352R-E 0/100 PSI 60-260˚F BACK SQUARE TRI-SQ-352R-G 0/200 PSI 80-320˚F BACK SQUARE TRI-SQ-352R-H 0/300 PSI 80-320˚F BACK SQUARE

Round Dial Tridicator Square Dial Tridicator

9”SCALE INDUSTRIAL THERMOMETERS

SIMPLE ADJUSTMENT Just two screws permit case to be rotated 180° and stem to be positioned in 10° increments allowing user to select the most desirable viewing position. EASY READABILITY Lens front blue reading spirit filled thermometer tube is mounted on V-shaped aluminum scale with bold black lines and numerals ACCURATE Calibrated against standards traceable to the National Institute of Standards and Technology and guaranteed accurate to ± one scale division CONSTRUCTION Black molded Cycolac plastic case with glass front to exclude dirt and dust is standard for ranges up 400°F*(200°C). Black enamled die cast aluminum case is standard for ranges 550° (285°C) and over and is also available for all ranges on special order. Plastic face is optional at additional charge. *Case should not be subjected to temperatures greater than 200°F CONNECTION ASSEMBLY Swivel nut has 1 1/4-18" NEF thread. Bulb chambers are tapered to insure proper fit in well.

NOTE Also available in Straight Form (Cat. No. 105) and 90° Back Angle Form (Cat. No. 115). Contact factory for price and availability.

STEM LENGTHS SCALE SIZE 3 1/2" 6" 9" 12"

7” AS5H7 AS5L7

9" AS5H9 AS5L9 AS5N9 AS5Q9

*Available Eco-Red filled – Add E to the end of the model number WHEN ORDERING: Specify (1) Thermometer Catalog No. from the table above (2) Specify Range(s) required.

Also available as Air Duct type and with thermowells

SOLAR DIGITAL THERMOMETER

The solar-powered DSI Series Thermometer fits any standard industrial thermometer well. The bold, hi-contrast display is easily read from greater distances than the typical glass tube thermometer. The unique design includes bi-directional solar panels, allowing the unit to collect light from multiple planes. The DSI Series Industrial Thermometer is furnished in one standard temperature range (-58 to 302°F & -50 to 150°C) which is switchable in the field greatly reducing inventory requirements. Features: Dual Solar Panels = Better light pick up in low light conditions F or C switching = less inventory for more applications Swivel + Angle Adjustment = suitable for all locations

SPECIFICATIONS Case: High Impact Abs Black Plastic Stem: Aluminum, 31/2” Or 6” Connection: 11/4” - 18 Unef Brass Jam Nut Sensor: Glass Passivated Thermistor Range: -58° To 302°F (-50 To 150°C), Field- Switchable Between °F & °C Display: Lcd, Black Character, 1/2” High With Gray Background

Illuminance: Bi-Directional Solar Collectors, 35 Lux Update Time: 6 Times Per Minute Accuracy: Greater Value Of 1° Or 1% Of Reading Resolution: 0.10° Between -58° To 199.9°F (-50° To 93°C) Recalibration: Internal Potentiometer Environmental Conditions: Ambient Temperature: -30° To 140°F (-35° To 60°C) Ambient Temperature Error: None Maximum Humidity: 100%

DIMENSIONS THERMOWELLS

DSI-FC-35 DSI-FC-6

Standard – Non Lagging

Lagging Extension

3 ½” Stem

6” Stem Brass 316SS

A 3.20 3.20 std TWB-35 T4E3D2 B 7.56 10.06

3 ½” lag TWB-35-LAG T4E3D2B C 5.75 8.25 std T1M3D2 T4M3D2

U 2.50 5.00 6”

lag T1M3D2E T4M3D2E

160 SERIES 5”SCALE THERMOMETER

STANDARD FEATURES • 5”White Painted Steel Scale • Black Marking • Dual Scale 40/280˚F & 15/135˚C • Red Liquid Filled (No Mercury) • ½”NPT Connection • Brass or Steel Well • Bottom or Back Connection • +/- 1 Scale Division Accuracy

163FS

162F

Type A B C E F G H J Bottom 7 ¾” 1 13/16” 3/8” 1” 2 1/8” 15/32” 7/8” ½”NPT Back 7” 1 13/16” 3/8” 7/8” 2 1/8” 15/32” 7/8” ½”NPT

Part # Stem Well 162F Bottom Brass 162FS Bottom Steel 163F Back Brass 163FS Back Steel

Model Numbers

DIAL INCREMENTS

RANGE Figures Major in Minor in 30/0"VAC -3” -1” -.2” 30/0/15 -3” / +3 PSI -1” / +1 PSI -.2” / +.2 PSI 30/0/30 -10” / +5 PSI -5” / +1 PSI -1” / .5 PSI 30/0/60 -10” / +10 PSI -5” / +5 PSI -1” / 1 PSI 30/0/100 -10” / +10 PSI -10” / + 5 PSI -2” / 1 PSI 30/0/150 -30” / +30 PSI -10” / +10 PSI -5” / 1 PSI 30/0/300 -30” / +30 PSI -10” / +10 PSI -5” / 2 PSI

0/15 1 PSI .1 PSI 0/30 3 PSI 1 PSI .2 PSI 0/60 5 PSI 1 PSI .5 PSI 0/100 10 PSI 5 PSI 1 PSI 0/160 20 PSI 10 PSI 1 PSI 0/200 20 PSI 10 PSI 2 PSI 0/300 30 PSI 10 PSI 2 PSI 0/400 50 PSI 10 PSI 2 PSI 0/500 50 PSI 10 PSI 5 PSI 0/600 50 PSI 10 PSI 5 PSI 0/800 100 PSI 20 PSI 4 PSI

0/1000 100 PSI 50 PSI 10 PSI 0/1500 100 PSI 10 PSI 0/2000 200 PSI 100 PSI 20 PSI 0/3000 300 PSI 100 PSI 20 PSI 0/4000 500 PSI 100 PSI 50 PSI 0/5000 500 PSI 100 PSI 50 PSI 0/6000 500 PSI 100 PSI 50 PSI

0/10,000 1,000 PSI 500 PSI 100 PSI 0/15,000 1,000 PSI 100 PSI

ANSI STANDARD ACCURACY GRADES

Notes: (1) Grade 4A Gauges must remain within specified tolerance before and after being lightly tapped

Permissible Error (+/- Percent Of Span ) (Excluding Friction) Accuracy

Grade

Lower ¼ of Scale Middle ¼ of Scale Upper ¼ of scale

Maximum Friction (% Of Span)

Minimum Recommended

Dial Size (270 Deg. Dial Arc)

4A ---------------------0.1------------------------- Note (1) 8 ½” 3A --------------------0.25------------------------ 0.25 4 ½” 2A ---------------------0.5------------------------- .05 2 ½” 1A ---------------------1.0------------------------- 1.0 1 ½” A 2.0 1.0 2.0 1.0 1 ½” B 3.0 2.0 3.0 2.0 1 ½” C 4.0 3.0 4.0 3.0 1 ½” D 5.0 5.0 5.0 3.0 1 ½”

STANDARD DIALS

30-0-100

30-0-150 30-0-200

30-0-400 30-0-600

400 PSI

800 PSI

10,000PSI 15,000PSI

MPa

Bar

kPa

Kg/cm²

cm

Mercury

mm

Hg (Torr)

Pa (N/m²)

mbar

cm

Water

mm

W

ater

oz/in²

Inches W

ater

Inches Mercury

ATMs

PSI

0.0069

0.0689

6.895

0.0704

5.17

51.715

6895

68.95

70.38

703.8

16

27.71

2.036

0.0681

1

PSI

0.1013

1.013

101.3

1.033

76

760

101,325

1013

1,034.3

10,343

235.1

407.2

29.92

1

14.7

ATMs

0.00339

0.0339

3.386

0.0345

2.54

25.4

3386

33.86

34.57

345.7

7.858

13.61

1

0.03342

0.4912

In. Hg.

0.00025

0.00249

0.249

0.00254

0.187

1.866

248.8

2.488

2.54

25.4

0.5775

1

0.0735

0.00246

0.0361

In. W

ater

STAN

DA

RD

0.00043

0.00431

0.431

0.0044

0.323

3.232

431

4.31

4.40

43.986

1

1.732

0.1273

0.00425

0.0625

oz/in²

0.00001

0.000098

0.0098

0.0001

0.00735

0.0735

9.8

0.098

0.1

1

0.0227

0.0394

0.00289

0.000097

0.001421

mm

water

0.0001

0.00098

0.098

0.001

0.0735

0.735

98

0.98

1 10

0.227

0.3937

0.0289

0.000967

0.01421

cm

water

0.0001

0.001

0.1

0.00102

0.075

0.75

100

1

1.021

10.21

0.2321

0.4012

0.0295

0.000987

0.0145

mbar

LOW

PRESSU

RE

0.000001

0.00001

0.001

0.00001

0.00075

0.0075

1

0.01

0.0102

0.102

0.00232

0.00402

0.000295

0.00001

0.000145

Pa (N/m

²)

0.000133

0.001333

0.1333

0.00136

.1 1

133.3

1.333

1.361

13.61

0.310

0.536

0.0394

0.001316

0.01934

Mm Hg

(Torr)

0.00133

0.01333

1.333

0.0136

1 10

1333

13.33

13.61

136.1

3.1

5.358

0.394

0.01316

0.1934

cm

Hg.

0.0981

0.981

98.07

1

73.56

735.6

98,067

980.7

1,001

100,010

227.6

394.1

28.96

0.968

14.22

kg/cm²

0.001

0.01

1

0.0102

0.75

7.05

1,000

10

10.207

102.07

2.321

4.019

0.295

0.00987

0.14504

kPa

0.1

1

100

1.02

75

750

100000

1000

1021

10,210

232.1

401.9

29.53

0.987

14.504

Bar

METR

IC

1 10

1,000

10.2

750

7500

1000000

10,000

10,207

102,074

2321

4019

295.3

9.869

145.04

MPa

MPa

Bar

kPa

Kg/cm²

cm

Mercury

mm

Hg (Torr)

Pa (N/m²)

mbar

cm

Water

mm

W

ater

oz/in²

Inches W

ater

Inches Mercury

ATMs

PSI

CO

NVER

SION

CH

AR

T

TEST AND CERTIFICATION

TEST AND CERTIFICATION OF PRESSURE GAUGES

1. All of our pressure gauges are manufactured to be in accordance with ANSI B-40.1-1985.

2. Each gauge is individually tested and calibrated during the assembly process.

3. Although each gauge is individually tested, they are not individually traceable to NIST Standards and therefore not Certified as a standard of production.

4. If certification of accuracy is required independent testing against a known and traceable standard (i.e.; a certified dead weight tester) will be required. This typically carries additional fees and charges – Please contact our sales department for more information.

5. If certificate of conformance is required we can typically supply this from our facility with minimal cost and time involved – Please contact our sales department for more information.

Although all of our gauges are manufactured and tested to be accurate and

in calibration, rough handling during shipment may cause pressure gauges to be ‘knocked out’ of calibration. This can happen even though good packaging practice was used. The American National Standard on pressure gauges (ANSI B40.1), recognizes this by including the following paragraph: “CAUTION TO USERS: PRESSURE GAUGES CAN BE RENDERED INACCURATE DURING SHIPMENT DESPITE CARE TAKEN IN PACKAGING. TO INSURE CONFORMANCE TO THE STANDARD GRADE TO WHICH THE PRESSURE GAUGE WAS MANUFACTURED, IT SHOULD BE CHECKED BEFORE USE.” Gauges received ‘off zero’ because of shipping damage can usually be brought back into calibration by a simple pointer adjustment. Please make sure your customers are aware of this information.

Limited Warranty

The Seller warrants all PIC instruments and equipment to be free from defects in workmanship or material under normal use and service for a period of one year from date of shipment. Liability under this warranty is limited to repair or replacement F.O.B. factory of any parts which prove to be defective within that time or repayment of the purchase price at the Seller’s option provided the instruments have been returned, transportation prepaid, within one year from date of purchase. All technical advice, recommendations and services are based on technical data and information which the Seller believes to be reliable and are intended for use by persons, having skill and knowledge of business, at their own discretion. In no case is Seller liable beyond replacement of equipment F.O.B. factory or the full purchase price. This warranty does not apply if the maximum ratings label is removed or if the instrument or equipment is abused, altered, used at ratings above the maximum specified, or otherwise misused in any way.

THIS EXPRESS LIMITED WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER REPRESENTATIONS MADE BY ADVERTISEMENTS OR BY AGENTS AND ALL OTHER

WARRANTIES, BOTH EXPRESS AND IMPLIED. THERE ARE NO IMPLIED WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE FOR GOODS COVERED

HEREUNDER.

Buyer’s Remedies

The Buyer’s exclusive and sole remedy on account of or in respect to the furnishing of non-conforming or defective material shall be to secure replacement thereof as aforesaid. The Seller shall not in any event be liable for the cost of any labor expended on any such material or for any special, direct, indirect, consequential or incidental damages to anyone by reason of the fact that it shall have been non-conforming or defective.

2.) PIC Gauge Catalog

Documents

Transcript of 2.) PIC Gauge Catalog