2 1iPASO EX LCT Training Manual(June2013)

TOPC-E4048E-02

iPASOLINK EX LCT WEB (Draft)

June 2013 Issue (F/W Ver. 1.00.20)

TOPC-E4048E-02 1

LCT COMMUNICATION INTERFACE

iPASOLINK EX WEB LCT

DCN Port supports DHCP default IP Address 172.17.254.253

Communication between the LCT and the EX is via the DCN Port connected by LAN cable

DCN PORT

TOPC-E4048E-02

LCT Startup and Login

Start the browser Internet Explorer and enter the URL http://172.17.254.253/weblct/ to open the WebLCT Login screen.

Enter the “User Name” and “Password” in the provided text boxes and Click Ok button

Default Username : Admin

Password: 12345678

LCT main menu opens in the “Current Status screen”

iPASOLINK EX WEB LCT 2

TOPC-E4048E-02

WebLCT LOGOUT

To Logout of the WebLCT, click on the Logout button on the top right hand of the LCT screen.

When Logout Confirm window appears, Click OK

LCT Login window appears

Close the Browser window to exit WebLCT.

Always Logout using this button before disconnecting the cable.


USER NAMES & PRIVILEGES Category Admin Config User REMOTE

File Operation Up/Down Load Up/Down Load Upload onlySNMP Operation Get/Set Get/Set Get

CURRENT STATUSEQUIPMENT SETUP EQUIPMENT / RADIO CONFIGURATION R/W R/W R

AMR CONFIGURATION R/W R/W R

NETWORK MANAGEMENT SETTINGGENERAL SETTING R/W R R

GENERAL SETTING (DETAIL) R/W R R

ROUTING SETTING R/W R R

IP ACCESS CONTROL SETTING R/W R R

DATE / TIME SETTING R/W R R

USER ACCOUNT / SECURITY SETTING

LOGIN USER LIST R/W R R

USER ACCOUNT MANAGEMENT R/W R R

USER GROUP PROFILE CONFIGURATION R/W R R

SECURITY MANAGEMENT SERVICE STATUS SETTING R/W R R

User: User is able to confirm system configuration and equipment status. It is not available to make any configuration change.

Password :87654321

Default Group: :OPERATOR

Config- Beside of the function can be performed by User, Config user is able to do radio management, base-band management, Switching function management for C-Plane control.

Password: 87654321

Default Group: CONFIG

Admin- Beside of the function can be performed by Config user, Admin user is able to do database management, file management, user management and time management for M-Plane control.

Password: 12345678

Default Group: ADMIN

REMOTE-Functions available When User access Remotely but restricted by the assigned access level


PROVISIONING

MODEM FUNCTION SETTING

MODEM PORT SETTING R/W R/W R

TX POWER SETTING R/W R/W R

ALM MODE SETTING R/W R/W R

AMR Setting R/W R/W R

ETH FUNCTION SETTING

BRIDGE SETTING R/W R/W R

ETH PORT SETTING R/W R/W R

VLAN SETTING R/W R/W R

FDB SETTING R/W R/W R

ETH OAM SETTING R/W R/W R

MSTP SETTING R/W R/W R

QoS /CLASSIFICATION SETTING R/W R/W R

L2CP TRANSPARENT SETTING R/W R/W R

LLF SETTING R/W R/W R

EQUIPMENT CLOCK / SETTING EQUIPMENT CLOCK SETTING R/W R/W R

ALARM SETTING

CORRELATION SETTING R/W R/W R

ALARM SEVERITY SETTING R/W R/W R

AIS SETTING R/W R/W R

BER THRESH HOLD SETTING R/W R/W R

4

USER NAMES & PRIVILEGES

MAINTENANCEMAINTENANCE CONTROL

LOOPBACK CONTROL MODEM LOOPBACK CONTROL

PROTECTION CONTROLMSTP SW CONTROL R/W R/W R

TIMING SOURCE SW CONTROL R/W R/W R

MODEM MAINTENANCE CONTROL R/W R/W R

H/W_F/W RESET CONTROLH/W RESET CONTROL R/W - -

F/W RESET CONTROL R/W - -

PMON / RMON/ FDB CLEAR R/W ROFFLINE MAINTENANCE R/W R

MAINTENANCE TEST ETH OAM LB/LT/LM/DM CONTROL R/W R R

PMON/RMON REPORTMODEM PMON REPORT R R R

ETH RMON REPORT R R R

VLAN COUNTER REPORT R R R

METERINGCURRENT METERING R R R

EQUIPMENT UITLITYEXPORT (NE->STORAGE) UTILITY R/W R/W -

UPDATE ( STORAGE -> NE ) UTILITY R/W - -

PROGRAM ROM SWITCHING R/W - -

LOG CLEAR FUNCTION R/W R/W -

SHIPMENT R/W - -

INVENTORYEQUIPMENT INVENTORY INFORMATION R R R

SOFTWARE LICENSE INFORMATION R R RSOFTWARE LICENSE SETUP

IMPORT LICENSE KEY R/W

User: User is able to confirm system configuration and equipment status. It is not available to make any configuration change.

Password :87654321

Default Group: :OPERATOR

Config- Beside of the function can be performed by User, Config user is able to do radio management, base-band management, Switching function management for C-Plane control.

Password: 87654321

Default Group: CONFIG

Admin- Beside of the function can be performed by Config user, Admin user is able to do database management, file management, user management and time management for M-Plane control.

Password: 12345678

Default Group: ADMIN

REMOTE-Functions available When User access Remotely but restricted by the assigned access level


CATEGORY Admin Config User REMOTEPROVISIONING

PMON / RMON THRESHOLD SETTING

PMON THRESHOLD SETTING R/W R/W R

PMON OTHER R/W R/W R

RMON THRESHOLD SETTING R/W R/W R

RMON OTHER R/W R/W R

5

TOPC-E4048E-02

WebLCT Initial Screen

Login User Name

Indicate the current logged in user

Summary Alarm Indication

Indicate the summary alarm of Equipment, TCN, & Maintenance Status

Opposite Site Links

Connect to opposite station

Maintenance

Maintenance ON/OFF button

Logout

Logout button

Menu tree

Indicate the LCT Main Menu

Detail Display

Display detail alarm & status information of items selected from the Tabs

When Log-in, Status window does not collect and show any information for faster startup. Click the Refresh button to view Active Alarms or Tabs for other status information.


TOPC-E4048E-02 7

WebLCT Initial Screen

F/W Version

Indicate the current Firm Ware Version

Site (NE) Name and IP Address

Indicate Network element name and it's IP address (login is Local or Remote)

Opposite Site Links

Show opposite station (s)

Connecting to opposite site

Click on the opposite site links and select the site to connect to. Dropdown List shows the other NEs connected through radio and Back-to-Back connections (inband back to back and NMS back to back). Login screen for selected opposite or Back-to-Back site open in a separate browser window

OR


TOPC-E4048E-02

Active Alarms & Event Log

Click on the Active Alarm Tab to see details of current Alarms

Click on Save button to save the active alarm list to the PC Click on Event Log tab to see the event Log information. Click save to save the event log to a CSV file

Auto Mode check box allows automatic refreshing of current status. Un check to stop auto refreshing

Event Log is divided in to three categories: Alarm – 1000 events Status – 1000 events Control – 1000 events Last 1000 items of each is stored.


TOPC-E4048E-02

Equipment Detail Alarm and Status

Click on the Equipment and GbE tabs to see the detail alarm and status information


TOPC-E4048E-02 10

Event Log – Filtering

Event Log data can be filtered based on the Severity. Click on the down arrow on the Severity column and select accordingly

Event Log columns can sort according to Ascending or Descending order . Bring the cursor to the column header and Click on the small down arrow select Sort Ascending or Sort Descending

Event Log data can be filtered based on the date. Click on the down arrow on the Date column and select accordingly

To see the Events on a particular date. Select the On check box and select the date from the calendar

To see the Events after or before a particular date. Select the Before or After check box and select the date from the calendar

To see the Events between two dates. Select the Before and After check boxes and select the dates from the calendar


TOPC-E4048E-02

WebLCT Main MenuMenus for Metering

Equipment UtilityS/W License setup

Can be accessed by selecting the check box “Detail Menu”

Click the “Expand All” icon to expand all menu items and click “ Collapsed All” icon to collapse the menu items


TOPC-E4048E-02

Main Menu

Click the “+” to expand each main menu folder and see the sub-menu items

iPASOLINK - EX-F/W Ver. 1.00.20

NE Branch SettingIn-band Management VLAN settingBridge IP Address setting


TOPC-E4048E-02

Provisioning Menu

Click the “+” to expand each main menu folder and see the sub-menu items

MAC Header Compression

ATPC MAX/Min RangeMTPC TX PowerRX Threshold



TOPC-E4048E-02

Maintenance Menu

ATPC Manual ControlTX Mute controlCW Control

TX MOD manual control



TOPC-E4048E-02

EQUIPMENT SETUP


TOPC-E4048E-02

EQUIPMENT CONFIGURATION (1 of 4)

Select the Equipment / Radio Configuration menu from the Equipment Setup Menu. screen opens showing the current equipment / Radio configuration .

Click the Setup icon to configure , modify the Radio configuration, equipment setup wizard opens in Step1. Detailed Equipment / Radio setting screen


TOPC-E4048E-02

Current setting of the Radio Configuration is shown in the left hand side

RADIO CONFIGURATION (2 of 4)

RF Information including Start/Stop frequencies, Frequency step Shift FrequencyTX upper or Lower bandSub Band used

of the EX is shown

Enter the NE Name xx Characters

Select the Channel Spacing (bandwidth)

Show the available Ether bandwidth

Select the TX Power Control Mode. ATPC or MTPC. Parameter setting for each mode is from provisioning menu

Enter the radio signal Frame ID (1 ~ 32)

Enter TX point frequency within the Start and Stop frequency of the RF Information shown.

Select the reference Modulation of the radio signal. It is the modulation used .in non AMR mode


TOPC-E4048E-02

RADIO CONFIGURATION (3 of 4)

Changed parameters are highlighted in blue. Confirm the changes and click the Ok button

In the confirmation window click OK button to continue to AMR Configuration Screen, or select Cancel to finish Radio configuration setting.


TOPC-E4048E-02

RADIO CONFIGURATION (4 of 4 )

Item Parameter DescriptionCurrent setting Current setting of the modem under configurationRF Information Frequency specification of the connected ODUNew Setting Allows setting of the selected modem radio configurationNE NameChannel Spacing 250MHz

50MH/500MHz (future)Specify the radio channel spacing

Reference Modulation

QPSK/16/32/64/[QAM] Specify the reference modulation from the list. In non-AMR mode this is the fixed modulation.In AMR mode TX power is limited to the available TX Power of the reference Modulation

ETH Bandwidth [Mbps] Available Ethernet BW for the selected channel spacing and Reference Modulation is shown

TX RF Frequency xxxxx.xxx [MHz] Enter transmit frequencyRX RF Frequency xxxxx.xxx [MHz] receive frequency

(automatically)Frame ID 1 - 32 Set frame IDTX Power Control MTPC/ATPC Set transmit power control

mode


TOPC-E4048E-02

AMR/Radio Mapping Configuration (1 of 2)

Set the AMR Modulation for Modem 1 & Click Next

Select AMR Operation by clicking the AMR Mode radio button. Select Non Operation radio button not to use the AMR function

Reference Modulation selected in Equipment/Radio Configuration is shown highlighted in green.

Select the other modulations to be used during AMR operation by selecting the appropriate Used radio button

Click the Next button.

Select AMR Configuration from the Equipment Setup menu.. AMR configuration screen shows the current AMR setting.


Click the Setup Icon. AMR Configuration wizard open in Step1

20

TOPC-E4048E-02

AMR/Radio Mapping Configuration (2 of 2)

Confirm the setting in the Step 2 confirmation screen is correct and click OK. If not click the Back button to go back and change the setting.


TOPC-E4048E-02 22

AMR STATUS

AMR alarm and status can be seen from the Current Status menu, Equipment tab.

Current TX and RX modulation status shows the modulation used..

The AMR Range Mismatch alarm indicate a mismatch between the local side and the opposite side AMR setting.This is due to the AMR range is not the same. (e.g. One side AMR Range is QPSK to 64 QAM, other side 16QAM to 64 QAM.)

Current TX and RX modulation status can also be monitored from the Current Metering screen


TOPC-E4048E-02

NETWORK MANAGEMENT


TOPC-E4048E-02

GENERAL SETTING

Item Parameter DescriptionIP Address Setting (Bridge 1) (Primary IP address Setting)IP Address x.x.x.x Input IP Address of NMS portSubnet Mask x.x.x.x Input Subnet Mask of NMS portDefault Gateway x.x.x.x Input Default Gateway IP

addressDCN Port SettingDCN Port LCT Port used for LCt connection

NMS Port used for NMS connectionNMS Port SettingConnect NMS Port to NMS

Yes Use NMS Port No Not use NMS Port

Select the General Setting from the Network Management Setting menu..

General setting current setting screen appears.

Click the Setup icon to open the General setting edit window.

This window allows the setting of bridge1 IP address, Subnet Mask and Default Gateway..

Select the radio Button LCT or NMS to Connect LCT or NMS to the DCN Port

Click the OK button to apply the setting

Bridge 1 IP address is the Primary IP address of the NE


Select the radio Button Yes or No for the Connect NMS port to NMS setting

24

TOPC-E4048E-02 25

GENERAL SETTING (Detail) (1 of 4)

Select the General Setting (Detail) from the Network Management Setting menu..

General Setting (Detail) Screen show the current settings of the detail network parameters.


TOPC-E4048E-02

GENERAL SETTING (DETAIL) 2 of 4Item Parameter Description

Inband Management VLAN SettingInband Management VLAN usage

Used / Not Used

Select Used or not used for Inband management

VLAN ID 1 ~ 4094 VLAN ID for Inband Management VLAN (default values are set for each stream, overwrite default values)

CoS 1-7 Class of service priority setting for inband VLAN tag sent from the IDU

Ethernet Port Setting DCNPort Mode LCT Select to connect LCT to DCN Port

NMS Select to connect NMS to DCN PortUsage Used Use Ethernet port

Not Used Not use Ethernet portAuto Negotiation Enable enable the Auto Negotiation of Ethernet port

Disable Disable the Auto Negotiation of Ethernet port

LLDP Setting

TX Interval (sec) 5~32767 Interval time for LLDP sending

TX Hold (Times) 2~10 TX Hold Value (TTL=TX Interval*TX Hold+1)

Auto Discovery Setting for DCN and MAIN PortsAuto Discovery LLDP Usage

Used or Not Used

Enable / disable auto search of the NEs through he selected ports

LLDP Mode Standard Enable working with standard LLDP MACProprietary MAC

Enable working with NEC proprietary LLDP MAC. This setting is useful when external layer2 switch (that discard standard LLDP frames,) are used to connect two iPasolink management ports


TOPC-E4048E-02 27

GENERAL SETTING (DETAIL) 3 of 4Item Parameter Description

Radio Bandwidth AdvertisementTX Advertisement Enabled/Disabled Insert radio BW information into LLDP

frameRX Advertisement Enabled/Disabled

NE Branch SettingDefault Gateway x.x.x.x Input the Default Gateway

item

DCN (NMS)portsModem PortInband Management

Appear when inband management is selected as used

Bridge No. bridge number for each of the above ports (1-20)Bridge IP Address IP Address for each BridgeBridge Subnet Mask

Subnet mask for each Bridge

M-Plane Bandwidth LimitationBandwidth Limitation

Enable or Disable Limits the BW used for SV signal over the Radio Frame

Bandwidth (Kbps) 500 to 10000 Kbps Set the BW of the SV signal over the radio

M-Plane PriorityCoS 5,6,7 CoS priority value for the SV signal

over the radioNMS Port Setting

Connect NMS Port to NMS

YES or No Select yes or no for NMS connection to the port

LCT Port SettingRestrict LCT Connection

Any Allow Local & Remote NE LCT accessOnly to Local NE Only Local NE access, Prevent

Remote NE LCT access


TOPC-E4048E-02

GENERAL SETTING (detail) 4 of 4

Select to which branch NMS port belongs to

Select to which branch Inband Mamagement belongs to

For each branch a bridge number is assigned. Input an IP address and subnet mask for each bridge.

For each port, modem and inband management # (used) listed select a Bridge to be associated


TOPC-E4048E-02

GENERAL SETTING (detail)

For DCN port used in NMS connection to use auto discovery select LLDP used.


For Main Port# used in in-band connection to use auto discovery select LLDP used.

29

TOPC-E4048E-02

DCN Configuration Example

PNMSj

Port01

VID 4095DCN

30iPASOLINK EX WEB LCT

VID 4095

NE-A192.168.1.78

DCN Port

NE-B192.168.1.79

NE-C192.168.1.80

DCN Port

DCN Port

Port01

TOPC-E4048E-02

Inband Management VLAN 100

Inband DCN Configuration Example

PNMSj

Port01 Port01Port01

• NE-A (192.168.1.78) Port01/MODEM1 Inband DCN

• Inband Management VLAN: 100

• Port01: Trunk Link

• MODEM1: Trunk Link

NE-D192.168.1.81

VID 4095VID 100

VID 4095 is automatically configured by software.

Inband VID

31iPASOLINK EX WEB LCT

Port01

VID 4095

NE-B192.168.1.79

NE-A192.168.1.78

NE-C1192.168.1.80

TOPC-E4048E-02

ROUTING SETTING


TOPC-E4048E-02 33

IP ACCESS CONTROL SETTING – Input Filter List

This function is used as an Access Control List

ADD Input Filter Entry Modify Input Filter Entry

Modify Rule

Delete Entry


TOPC-E4048E-02 34

IP ACCESS CONTROL SETTING–Forwarding Filter List

ADD Input Filter Entry


TOPC-E4048E-02 35

DATE / TIME SETTING

Select the Date, and enter the Time. Select the time zone and click the OK button

Select Date/Time Setting from the Equipment Utility Menu

Click the Modify icon to set the date and time

To set the PC time as the EX date / time, select the check box Display PC Time and click the OK button.


TOPC-E4048E-02

MAINTENANCE CONTROL


TOPC-E4048E-02

LOOPBACK CONTROL


TOPC-E4048E-02

MAINT Control- Modem Loopback Control

If Maintenance mode is selected before applying the maintenance control “ Switch to Maintenance mode first warning message appears

IF loopback cuts the TX output affecting the radio link

Click on Maintenance button on the top of LCT window to enter maintenance mode.

Expand the Maintenance Control from LCT menu。

Expand the Loopback Control from Maintenance Control sub menu.

Select the MODEM Loopback Control from Loopback Control sub menu.

MODEM Loopback Control Window is displayed. Click on Off of the MODEM field of L2 Loopback

Click on the L2 Loopback drop down list and select Loopback1 (near end) or Loopback2 (far end)

Click the OK button to apply the maintenance control of the selected L2 Loopback.

If the Modem L2 Loopback is for the remote NE, then select the Release time

Click OK button to apply the maintenance control. Off indication will turn to Onwith Yellow background


Modem L2 Loopback provide Ethernet loopback in near end and far end directions. Ethernet frame destination and source MAC addresses will be swapped during the loopback.

38

TOPC-E4048E-02 39

LOOPBACK CONTROL

Event Log shows the control actions for modem L2 loopback


Highlighting indicate a maintenance control is applied

TOPC-E4048E-02 40

PROTECTION CONTROL


TOPC-E4048E-02 41

Protection Control- RSTP / MSTP Control

Select MSTP Control under the Maintenance Control, Protection Controlmenu. Protection Control- RSTP Control or MSTP Control screen display current RSTP or MSTP status

Click the MSTP Clear icon, to initialize the MSTP process.

Click the OK button on the warning dialog box to continue the MSTP clear control.


TOPC-E4048E-02 42

Protection Control- Timing Source SW ControlSelect Timing Source Switch Control under the Maintenance Control, Protection Control menu. Protection Control- Timing Source Switch Control screen display current timing sources selected and switch control status and lockout status.

To manually select a timing source, click on the timing source status under the Timing Source SW controlcolumn of the open the Timing Source Switch control Window

Click on the drop down menu and select Manual SW (if the timing source in normal) or Forced SW (if the timing source is under alarm condition) and select OK.

Select Normal to release the switch control and click OK.

To Lock Out the timing source from being used as a timing source in the equipment, click the Off status under the Lock Out column for the selected Timing source. Timing Source Switch control window for lock out opens.

Select the appropriate radio button ON or OFF and select OK ..

Status of the maintenance control is shown by the yellow background with the switched status


TOPC-E4048E-02

Modem Maintenance Control-ATPC Manual

•ATPC Manual ControlIf TX Power Control Mode selected is ATPC Mode, it is possible to temporarily disable ATPC mode under maintenance control and transmit a fixed transmit power.

Select ATPC Manual Control On radio button and enter required ATPC Manual power output level within the limits shown.

Click OK button to apply the manual TX control.

This may be required during antenna alignment.


TOPC-E4048E-02

Modem Maintenance CTRL – Mute/CW/Modulation

This maintenance Control switch off the TX output power of the ODU connected to the selected modem

This maintenance Control TX an un-modulated carrier from the selected modem

This maintenance Control select a fixed modulation when the modem is under AMR mode . Select auto to go back to AMR mode starting with QPSK modulation and adjust according to the propagation condition

When TX Mute and CW Control is applied to the NE remotely, it is possible to select an automatic release timer. (these two controls interrupt the radio link) at the end of the timer value the control will be released normalizing the linkCW Function is Not Supported in Remote


TOPC-E4048E-02

H/W _ F/W RESET CONTROL


TOPC-E4048E-02

MAINT Control- H/W Reset Control

Reset control requires the Maintenance Mode to be On


Select the H/W / F/W Reset Control from the Maintenance Control menu..

H/W Reset Control Screen show the Equipment H/W details

Select the H/W Reset Control

Click the Equipment in H/W Reset Control Screen, to open the Equipment Reset Control window, Click Ok to Rest the . Equipment

46

TOPC-E4048E-02

F/W RESET CONTROL

Reset control applies under Maintenance Mode


Select the H/W / F/W Reset Control from the Maintenance Control menu..

F/W Reset Control Screen show the F/W information of BB (BaseBand ) section and RF section

Select the F/W Reset Control

Click BB or RF in the F/W reset Control screen to reset the Baseband or RF section Firm Ware.

Click here to go to Program ROM switching screen in the Equipment Utility Menu

47

TOPC-E4048E-02 48

PMON / RMON / FDB CLEARSELECT PMON /RMON /FDB CLEAR FROM THE MAINTENANCE CONTROL MENU

SELECT PMON /RMON CLEAR RADIO BUTTON AND CLICK THE EXECUTE ICON

CLICK THE OK BUTTON TO CLEAR THE PMON / RMON DATA

SELECT FDB TABLE CLEAR RADIO BUTTON AND CLICK THE EXECUTE ICON


SELECT “ALL” RADIO BUTTON AND CLICK THE OKBUTTON TO CLEAR ALL FDB DATA

SELECT “VLAN ID” RADIO BUTTON AND ENTER THE VLAN ID. CLICK THE OK BUTTON TO CLEAR FDB DATA OF THE SELECTED VLAN.

SELECT “PORT” RADIO BUTTON AND SELECT THE BOARD AND THE PORT FROM THE RESPECTIVE DROP DOWN MENUS. CLICK THE OK BUTTON TO CLEAR FDB DATA OF THE SELECTED PORT.

TOPC-E4048E-02

OFFLINE MAINT CONTROL-

IHG ODU CAN CHANGE THE FREQUENCY SUB BAND BY CHANGING THE TX/RX RF BPF. AFTER CHANGING THE SUBBAND FILTER NEW SUB BAND LETTER USED SHOULD BE SET IN THE ODU USING THIS OFFLINE CONTROL. IF YOU CHANGE THIS PARAMETER WITHOUT CHANGING THE SUB BAND FILTER RADIO LINK MAY FAIL.

SELECT FROM THE DROP DOWN LIST THE SUB BAND LETTER TO BE USED AND CLICK THE SETBUTTON


F/W ver 1.0017

49

TOPC-E4048E-02

METERING


TOPC-E4048E-02

Metering -

Metering data are refreshed every 10 seconds. To have faster refreshing rate during adjustments, click the Modem and select the High speed (3Sec) radio button.

After the adjustment exit this window by clicking the cancel buttonSelect the Current Metering from the Metering menu. Current metering screen shows:TX Power in dBm RX Level in dBmODU power Supply in voltsBERTX Modulation (Current)RX Modulation (Current)


TOPC-E4048E-02

INVENTORY


TOPC-E4048E-02

INVENTORY - IDU

This MAC Address selected for RSTP Root Bridge

MAC Address of ports required for

Ether OAM


Select the Equipment Inventory Information from the Inventory menu..

Inventory Information of HardwareFirm WareFPGAModem ParameterFrequencyManagement MAC AddressesUser Port Modem Port MAC Addresses

Click the Export Equipment Inventory Information icon to save the Inventory information.

53

TOPC-E4048E-02

S/W License Information


Select the S/W License Information from the Inventory menu..

Current S/W License Information status is shown.

Click the Export S/W License Information icon to save the Inventory information.

54

TOPC-E4048E-02

S/W License Setup


TOPC-E4048E-02

S/W LICENSE SETUP – IMPORT LICENSE KEY


Select the S/W License Setup menuSelect Import License Key

Current S/W Key information is shown in Import License Key screen

Click the Setup icon to import the License Key

Browse to the location where the License key is and select the file. Click Ok to Import the License file.

Indicate the progress of the License file down load

56

TOPC-E4048E-02

Equipment Utility


TOPC-E4048E-02

Equipment Utility- Export (NE>Storage) Utility

Use this function to export the Equipment Config Data, Network Config Data and User Config Data from NE to storage (Local PC)

Data Type Default File Name

Equipment Configuration Data iPASOLINK-equip.cfg

Network Configuration Data iPASOLINK-network-typeB.cfg

User Configuration Data iPASOLINK-user.cfg

Inventory data Invent_EX_********_YYYMMDD.csv


TOPC-E4048E-02

Program downloadsUse this function to download Program File, FPGA Data and Config Data from storage (Local PC) to update the NE.


TOPC-E4048E-02 60

Program downloadsUse this function to download Program File, FPGA Data and Config Data from storage (Local PC) to update the NE.


TOPC-E4048E-02 61

Partial Equipment Config DownloadUse this function to download Program File, FPGA Data and Config Data from storage (Local PC) to update the NE.

1 From the Equipment Utility menu select Update (Storage-> NE ) Utility

Put the Equipment to Maintenance mode and select Config Data radio button.

2

Click the Execute button3

In the Update (storage-> NE) utility Config Data window click the select Config data type drop down list arrow. Select Partial Equipment Config

4

Browse to the location where the Equipment config file is located and select the config file. Click the Next button

5

Select the configuration items to upload by selecting from the check boxes. Click OK.

6


TOPC-E4048E-02

Equipment utility Program ROM Switching

iPasolink uses the program version in the current (foreground) memory bank for its operation. It is possible to have the previous version of the firmware to be in the un-current (back ground) memory bank. To go back to the previous version of the firmware use this function to switch the memory banks.


TOPC-E4048E-02 63

LOG CLEAR FUNCTION

Select Log Clear Function from the Equipment Utility Menu..

Select the Radio button of the Log Type to be cleared, Alarm Log, Status Log, Command Log or All Logs and click the Execute button

Click OK on the confirmation screen. When complete information window opens click OK.

MAINTENACE MODE

1

2

3

Command Log Cleared


TOPC-E4048E-02

SHIPMENT SettingThis feature allows the clearing of Equipment Configuration, Radio Configuration and the Provisioning items to configure the equipment from the factory default setting

Select Shipment from the Equipment Utility Menu

Click the Shipment icon from the equipment Utility-shipment screen.

Select Provisioning clear from the drop down menu of the shipment control window.

Click Ok . LCT will be disconnected during the Provisioning clear operation.

Login again to configure the IDU after the Provisioning clear.


TOPC-E4048E-02

User Account / Security Setting


TOPC-E4048E-02

LOGIN USER LIST

Click on the User name to modify the logged in user's password or user group.

LOGIN USER LIST menu shows a list of Users logged in to the NE, locally and remotely. “ * “ shows user ID of this user.

Click on the Set Password In User Setting window to change the User Password

To change the User Group click on the Group field and select from the drop down list the group to be changed to.

Following User parameters can be modified:

GroupSecurity LevelPasswordAuth Algorithm and KeyPriv Algorithm and key


TOPC-E4048E-02

USER ACCOUNT / SECURITY SETTING

Item Parameter

User Name 1 t0 31 Characters

Password 8 to 31 Characters

Group Default Groups ADMIN/CONFIG/OPERATOR or Added Groups

Security Level :NoAuthNoPriv

User Login Without authentication and encryption

Security Level :AuthNoPriv

User Login need authentication (MD5 or SHA1 based) but without (Privacy) encryption

Security Level :AuthPriv

User Login need Authentication (MD5 or SHA1 ) and the data is encrypted by DES or AES

Auth Algorithm Select Authentication Algorithm between MD5 or SHA

Auth Key Input 8 to 16 digit Public key of MD5 and SHA1

Priv Algorithm Select the encryption method DES or AES

Priv Key Input 8 to 16 digits Key of DES or AES

MD5 ( Message Digest 5 ) one of the Hash Algorithm for authentication and digital signature. In order to detect the falsification of original data during the data transmission. Original data will be converting the Hash by comparing at both ends

SHA (Secure Hash Algorithm ) one of the Hash Algorithm for authentication and digital signature. In order to detect the falsification of original data during the data transmission. Less than 264 bits of original data will be converting the Hash of 160 bits by comparing at both ends

DES (Data Encryption Standard ) is 56 bit encryption key and encryption by 64 bit block

AES (Advanced Encryption Standard ) SPN structured block encryption, block length is 128 bits and the length of key 128/192/256 bits


TOPC-E4048E-02

USER ACCOUNT MANAGEMENT – Add User

User Account Management function allows adding , Modifying and deleting of User accounts.This function is available for Admin Access level users onlyUp to nine user accounts can be added in addition to the three default user accounts (User, Config & Admin).

Click on the ADD USER icon on the Use Account / Security Settingwindow. Enter the User Name and select the Group from the drop down list of registered user groups.

Click on the Set Auth Key and Set Priv Key icons on the User Settingwindow. Enter the Auth Key and Priv Key for the new user. Click OK

Click on the OK button to register the new user.

Click on the Set Password icon on the User Setting window. Enter the Password for the new user. Click OK


TOPC-E4048E-02

USER ACCOUNT MANAGEMENT Modify/Delete User

MODIFY USER

DELETE USER

Following User parameters can be modified:

GroupSecurity LevelPasswordAuth Algorithm and KeyPriv Algorithm and key

Click the Delete User icon . From the User Setting window select the User Name to be deleted from the drop down list.

Click OK to delete the selected User

Click the User name to be modified.

Click OK to apply the modification to the selected User.


TOPC-E4048E-02

USER GROUP PROFILE CONFIGURATION

PARAMETER DESCRIPTION

Group Name 1 to 32 characters

FTP Allow or Deny using FTP protocol

HTTP Allow or deny using HTTP protocol for WebLCT to access Equipment

SNMP Allow or deny using SNMP protocol to access network equipment

Access Level Specify the User Access Level

In addition to the three default groups (OPERATOR/CONFIG/ ADMIN) Sixadditional groups can be registered.

MODIFY USER GROUP ADD USER GROUP

Click the Delete Group icon . From the Group Setting window select the Group Name to be deleted from the drop down list.

Click OK to delete the selected Group


TOPC-E4048E-02 71

Service Status Setting


TOPC-E4048E-02

SECURITY MANAGEMENT

Protocol or Service Enabled

Protocol or Service Disabled


TOPC-E4048E-02

SECURITY MANAGEMENT


TOPC-E4048E-02

SNMP and SNMP Community SETTING

Default UDP Port is 161

Item Parameter Description

Community Name Use ASCII within 255 Characters

Set the SNMP community name. Any request with different community name will be refused

Access Level CONFIG- allows only GETADMIN – Allows GET and SET

Assign the access level to the specified server(s)

Access address xxx.xxx.xxx.xxx Specify the valid IP address or network of the SNMP Manager(s)

Subnet Mask 255.xxx.xxx.xxx Subnet Mask of SNMP Manager(s)

Up to 10 SNMP Managers, including PNMSj and MS 5000 can access the iPASOLINK Network


TOPC-E4048E-02

SNMP Trap Entry SETTING


SNMP Version V1 / v2c / v3 Set SNMP version for trap

PDU Type Trap / Inform Set PDU Type for Trap

IP Address 0.0.0.0 Specify the destination IP address of trap

Port 162 (default) (1 t0 65535) Set UDP Port trap

Community name

255 Character Set communication name of the trap. This must match on both SNMP server and agent

Security Level NoAuthNoPriv/ AuthNoPriv/AuthPriv

SNMP Engine ID

Auth Algorithm MD5 or SHA

Auth Key 8 to 16

Priv Algorithm DSE or AES

Priv Key 8 to 16

This setting applies to the additional SNMP managers not to PNMSj or MS5000


TOPC-E4048E-02

NTP SETTING


TOPC-E4048E-02

FTP and HTTP setting


FTP Enable (Running)Disable (Stopped)

Start and Stop FTP service

TCP Port (Command)

21(default Set TCP port of FTP server (for received command) ) (1 to 65535)

TCP Port (Data) 20 (Default) Set the TCP port of FTP server (for data transmit) (1 to 65535)

Max session 3 Maximum user connection

Auto Stop Enable Enable FTP server break the connection in 90 sec automatically after no operation on the client

Disable Disable FTP server break automatically


HTTP Enable (Running)Disable (Stopped)

Start and Stop HTTP service

TCP Port 80(default) Set the port number of HTTP server (1 to 65535)


2 1iPASO EX LCT Training Manual(June2013)

Documents

Transcript of 2 1iPASO EX LCT Training Manual(June2013)