14T1L

SERVICE MANUAL14T1-1L

COLOUR TELEVISIONChassis No. GA6

14T1-LIn the interests of user safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts indentical to those specified should be used.

S878314T1L

MODEL

ELECTRICAL SPECIFICATIONS

Chassis No. GA7M

CONTENTSIMPORTANT SERVICE SAFETY PRECAUTION ................................................................................................... 1-1

Page

LOCATION OF USER’S CONTROL ...................................................................................................................... 2-1INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................................. 3-1SERVICE MODE ..................................................................................................................................................... 4-1ADJUSTMENT METHOD ........................................................................................................................................ 5-1WAVEFORMS ......................................................................................................................................................... 6-1CHASSIS LAYOUT ................................................................................................................................................. 7-1BLOCK DIAGRAM .................................................................................................................................................. 8-1DESCRIPTION OF SCHEMATIC DIAGRAM .......................................................................................................... 9-1SCHEMATIC DIAGRAMS ......................................................................................................................................10-1PRINTED WIRING BOARD ASSEMBLIES ........................................................................................................... 11-1Parts Guide

POWER INPUT............................AC 110-220 V, 50/60 Hz POWER RATING .....................................................62WPICTURE SIZE .............................581 cm2(90.06 sq inch)CONVERGENCE ............................................. MagneticSWEEP DEFLECTION .................................. .. Magnetic FOCUS ........................................................ Electrostatic INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency ...................... 45.75 MHz Sound IF Carrier Frequency ...................... 41.25 MHz Color Sub-Carrier Frequency ......................42.17 MHz (Nominal)AUDIO POWER OUTPUT RATING... ................................... 3.0 W(RMS)

SPEAKER SIZE ................................................................. 2” X 3.5” VOICE COIL IMPEDANCE .................16 ohm at 400 HzANTENNA INPUT IMPEDANCE VHF/UHF ........................................75 ohm UnbalancedTUNING RANGES VHF-Channels ................................................. 2 thru 13 UHF-Channels ................................................14 thru 69 CATV Channels ............................................. 1 thru 125 (EIA, Channel Plan U.S.A.)

Specifications are subject to change without

prior notice.

SHARP CORPORATION This document has been published to be used for aftersales service only.The contents are subject to change without notice.

14T1-L
TV14T1-LService Manual14T1-LMarketE CHAPTER 1. IMPORTANT SERVICE SAFETY PRECAUTION
[1] IMPORTANT SERVICE SAFETY PRECAUTION

IMPORTANT SERVICE SAFETY PRECAUTIONService work should be performed only by qualified service technicians who are

thoroughly familiar with all safety checks and the servicing guidelines which follow:

X-RADIATION AND HIGH VOLTAGE LIMITS

1. Be sure all service personnel are aware of the

procedures and instructions covering X-radiation.

The only potential source of X-ray in current solid

state TV receivers is the picture tube. However, the

picture tube does not emit measurable X-Ray

radiation, if the high voltage is as specified in the

"High Voltage Check" instructions.

It is only when high voltage is excessive that X-

radiation is capable of penetrating the shell of the

picture tube including the lead in the glass material.

The important precaution is to keep the high voltage

below the maximum level specified.

2. It is essential that servicemen have available at all

times an accurate high voltage meter.

The calibration of this meter should be checked

periodically.

3. High voltage should always be kept at the rated value

−no higher. Operation at higher voltages may cause

a failure of the picture tube or high voltage circuitry

and;also, under certain conditions, may produce

radiation in exceeding of desirable levels.

4. When the high voltage regulator is operating properly

there is no possibility of an X-radiation problem.

Every time a color chassis is serviced, the brightness

should be tested while monitoring the high voltage

with a meter to be certain that the high voltage does

not exceed the specified value and that it is regulating

correctly.

5. Do not use a picture tube other than that specified

or make unrecommended circuit modifications to the

high voltage circuitry.

6. When t roub le shoo t ing and tak ing tes t

measurements on a receiver with excessive high

voltage, avoid being unnecessarily close to the

receiver.

Do not operate the receiver longer than is necessary

to locate the cause of excessive voltage.

WARNING

1. For continued safety, no modification of any circuit

should be attempted.

2. Disconnect AC power before servicing.

3. Semiconductor heat sinks are potential shock

hazards when the chassis is operating.

4. The chassis in this receiver has two ground systems

which are separated by insulating material.The non-

isolated (hot) ground system is for the B+ voltage

regulator circuit and the horizontal output circuit.The

isolated ground system is for the low B+ DC voltages

and the secondary circuit of the high voltage

transformer.

To prevent electrical shock use an isolation

transformer between the line cord and power

receptacle, when servicing this chassis.

SERVICING OF HIGH VOLTAGE SYSTEM

AND PICTURE TUBE

When servicing the high voltage system,

remove the static charge by connecting a

10k ohm resistor in series with an insulated

wire (such as a test probe) between the pic-

ture tube ground and the anode lead. (AC

line cord should be disconnected from AC

outlet.)

1. Picture tube in this receiver employs integral

implosion protection.

2. Replace with tube of the same type number for

continued safety.

3. Do not lift picture tube by the neck.

4. Handle the picture tube only when wearing

shatterproof goggles and after discharging the high

voltage anode completely.

1 – 1

14T1-L

SAFETY NOTICE

Many electrical and mechanical parts in television

receivers have special safety-related characteristics.

These characteristics are often not evident from visual

inspection, nor can protection afforded by them be

necessarily increased by using replacement components

rated for higher voltage, wattage, etc.

Replacement parts which have these special safety

characteristics are identified in this manual; electrical

components having such features are identified by " "

and shaded areas in the Replacement Parts Lists and

Schematic Diagrams.

IMPORTANT SERVICE SAFETY PRECAUTION(Continued)

1. Inspect all lead dress to make certain that leads are

not pinched or that hardware is not lodged between

the chassis and other metal parts in the receiver.

2. Inspect all protective devices such as non-metallic

control knobs, insulating materials, cabinet backs,

adjustment and compartment covers or shields,

isolation resistor-capacity networks, mechanical

insulators, etc.

3. To be sure that no shock hazard exists, check for

leakage current in the following manner.

Plug the AC cord directly into a 110~220 volt AC

outlet, (Do not use an isolation transformer for this

test).

Using two clip leads, connect a 1.5k ohm, 10 watt

resistor paralleled by a 0.15µF capacitor in series

with all exposed metal cabinet parts and a known

earth ground, such as electrical conduit or electrical

ground connected to earth ground.

Use an AC voltmeter having with 5000 ohm per volt,

or higher, sensitivity to measure the AC voltage drop

across the resistor.

BEFORE RETURNING THE RECEIVER

(Fire & Shock Hazard)

Before returning the receiver to the user, perform

the following safety checks.

Connect the resistor connection to all exposed metal

parts having a return to the chassis (antenna, metal

cabinet, screw heads, knobs and control shafts,

escutcheon, etc.) and measure the AC voltage drop

across the resistor.

AII checks must be repeated with the AC line cord

plug connection reversed. (If necessary, a non-

polarized adapter plug must be used only for the

purpose of completing these check.)

Any current measured must not exceed 0.5 milliamp.

Any measurements not within the limits outlined

above indicate of a potential shock hazard and

corrective action must be taken before returning the

instrument to the customer.

For continued protection, replacement parts must be

identical to those used in the original circuit. The use of

substitute replacement parts which do not have the same

safety characteristics as the factory recommended

replacement parts shown in this service manual, may

create shock, fire, X-radiation or other hazards.

DVM

AC SCALE

1.5k ohm10W

TO EXPOSEDMETAL PARTS

CONNECT TOKNOWN EARTHGROUND

•

•

•

•

1 – 2

14T1-L

2 – 1

TV14T1-LService Manual14T1-LMarketE CHAPTER 2. LOCATION OF USER'S CONTROL

[1] LOCATION OF USER'S CONTROL

LOCATION OF USER'S CONTROL

Infrared Transmitter Window

INPUT

Press Switch to external videoINPUT 1 mode..

Press 3 times Switch back to theoriginal TV mode.

REMOTE KEYPAD

Accesses any channel from keypad.

CHANNEL UP/DOWN

( ) Selects next higher channel.( ) Selects next lower channel.

Moves the highlight bar of the

MENU screens.

MENU

Press Accesses MAIN MENU.Press again Exits MAIN MENU.

TV

0

1

4

7

2

5

8

3

6

9

100

CH

CH

VOL- +

VOL

POWER

Press On.Press again Stand by..

FLASHBACK

Return to previous channel.

VOLUME UP/DOWN

(+) Increases sound.(_) Decreases sound.

In menu mode, changes or selectsthe TV adjustments.

DISPLAY

Press Displays receiving channeland Off Timer on the screen.Press again Removes display.

MUTE

Press Mutes sound.Press again Restores sound.

POWERINPUT

FLASHBACK

MENU

MUTE DISPLAY

Basic Remote Control Functions

ANTENNA/CABLE

INPUT TERMINAL

AV-1 IN/INPUT-1 TERMINALS

AV OUT TERMINALS

Press 2 times Switch to externalvideo INPUT 2 mode.

14T1-L

3 – 1

TV14T1-LService Manual14T1-LMarketE CHAPTER 3. INSTALLATION AND SERVICE INSTRUCTIONS

[1] INSTALLATION AND SERVICE INSTRUCTIONS

CIRCUIT PROTECTION

The receiver is protected by a 3.15A fuse (F701),

mounted on PWB-A, wired into one side of the AC

line input.

X-RADIATION PROTECTOR CIRCUIT TEST

After service has been performed on the horizontal

deflection system, high voltage system, B+ system,

test the X-Radiation protection circuit to ascertain

proper operation as follows:

1. Apply 110~220V AC using a variac transformer for

accurate input voltage.

2. Allow for warm up and adjust all customer controls

for normal picture and sound.

3. Receive a good local channel.

4. Connect a digital voltmeter to C602 +ve Terminal

and make sure that the voltmeter reads 20±1.1V.

5. Apply external 27V DC at C602 +VE Terminal by

external DC supply, TV must shut off.

6. To reset the protector, unplug the AC cord and

remove external 27V DC at C602 +VE Terminal.

Now make sure that normal picture appears on the

screen.

7. If the operation of the horizontal oscillator does not

stop in step 5, the circuit must be repaired before the

set is returned to the customer.

HIGH VOLTAGE CHECK

High voltage is not adjustable but must be checked

to verify that the receiver is operating within safe

and efficient design limitations as specified checks

should be as follows:

1. Connect an accurate high voltage meter between

ground and anode of picture tube.

2. Operate receiver for at least 15 minutes at 110~220V

AC line voltage, with a strong air signal or a properly

tuned in test signal.

3. Enter the service mode and set Y-mute ON by using

Service R/C.

4. The voltage should be approximately 24KV (at zero

beam).

If a correct reading cannot be obtained, check circuitry

for malfunctioning components. After the voltage test,

make Y-mute off to the normal mode.

INSTALLATION AND SERVICE INSTRUCTIONSNote: (1)When performing any adjustments to resistor controls and transformers use non-metallic

screwdrivers or TV alignment tools.

(2) Before performing adjustments, the TV set must be on at least 15 minutes.

using an

14T1-L
TV14T1-LService Manual14T1-LMarketE CHAPTER 4. SERVICE MODE
[1] SERVICE MODE

1. Service mode is switched by SERVICE key, CH UP + VOL DOWN when reset.

2. Service mode is cancelled by SERVICE key during service mode.

3. Service mode can be switched to the following 2 modes via MENU key;

4. During Service mode, AFT operation is prohibited. The setting data for PLL is always set to f

5. During Service mode, the following user data are set to default value.

PICTURE/TINT/COLOR/BRIGHT/SHARP/COLOR TEMP.(FAV.COLOR)/PICTURE NR/

ENERGY SAVE/OFF TIMER

Adjustment mode

NVM Edit Mode

First Mode of Service when entering by SERVICE

key.

SERVICE MODE

7. During Service mode, sound is muted except when selecting the following items.

35 SUB-VOL

6. During Service mode, the following operation are prohibited.

No signal BLUE SCREEN

data.°

4 – 1

14T1-L

Caution: To go into the service mode, one of the ways is press direct key for service items.

D7 D6 D5 D4 D3 D2 D1 D0 (DEC) (HEX) (DEC) (HEX)

0 0 0 8 23 17 63 17

0 0 0 9 31 1F 63 1F

0 0 0 A 36 24 63 24

0 0 0 B 20 14 63 14

0 0 0 C 30 1E 63 1E

0 0 0 D 28 1C 63 1C

0 0 0 E 36 24 63 24

0 0 0 F 30 1E 63 1E

0 0 1 0 30 1E 63 1E

0 0 1 1 42 2A 63 2A

0 0 1 2 44 2C 63 2C

0 0 1 3 30 1E 63 1E

0 0 1 4 28 1C 63 1C

0 0 1 5 16 10 63 10

0 0 1 6 32 20 63 20

0 0 1 7 32 20 63 20

0 0 1 8 32 20 63 20

0 0 1 9 16 10 63 10

0 0 1 A 16 10 63 10

0 0 1 B 32 20 63 20

0 0 1 C 25 19 63 2D (BUS SETUP)

0 0 1 D 10 0A 63 0A

0 0 1 E 36 24 63 24

0 0 1 F 32 20 63 20

0 0 2 0 32 20 63 20

0 0 2 1 32 20 63 20

0 0 2 2 32 20 63 20

0 0 2 3 32 20 63 20

0 0 2 4 32 20 63 20

0 0 2 5 24 18 63 18

0 0 2 6 48 30 63 30

0 0 2 7 32 20 63 20

0 0 2 8 32 20 63 20

0 0 2 9 32 20 63 20

0 0 2 A 37 25 63 25

0 0 2 B 32 20 63 20

0 0 2 C 32 20 63 20

0 0 2 D 38 26 63 26

0 0 2 E 32 20 63 20

0 0 2 F 19 13 63 13

0 0 3 0 32 20 63 20

0 0 3 1 32 20 63 20

0 0 3 2 32 20 63 20

0 0 3 3 32 20 63 20

0 0 3 4 32 20 63 20

0 0 3 5 32 20 63 20

0 0 3 6 32 20 63 20

0 0 3 7 32 20 63 20

0 0 3 8 32 20 63 20

0 0 3 9 32 20 63 20

0 0 3 A 32 20 63 20

0 0 3 B 32 20 63 20

EEPROM ITEMS

Memory Map Data

NVM address

CUT-RW-DVD

CUT-GW-DVD

CUT-GC-DVD

DRI-RW-DVD

DRI-GW-DVD

DRI-BW-DVD

DRI-RC-DVD

DRI-GC-DVD

DRI-BC-DVD

CUT-RC-DVD

DRI-GW

DRI-BW

CUT-RW

CUT-GW

DRI-BC

CUT-RC

CUT-GC

DRI-RW

SUB-CON-DVD

SUB-TINT-DVD

DRI-RC

DRI-GC

DRI-BS-DVD

CUT-RS-DVD

CUT-GS-DVD

SUB-BRI-DVD

SUB-TINT

SUB-SHARP

DRI-RS-DVD

DRI-GS-DVD

CUT-GS

SUB-BRI

SUB-CON

SUB-COL

DRI-RS

DRI-GS

DRI-BS

CUT-RS

LOCOR-PAR

E/W-TRAP

V-LIN

S-COR

E/W-PAR-50

H-PAR

H-BOW

UPCOR-PAR

SETTING DATADefault

H-SHI-50

EW-W-50

Default MAX

RF-AGC

V-SLOPE

V-SHI-50

V-AMP-50

4 – 2

14T1-L


0 0 3 C 39 27 63 27

0 0 3 D 35 23 63 23

0 0 3 E 31 1F 63 1F

0 0 3 F 11 B 63 B

0 0 4 0 32 20 63 20

0 0 4 1 32 20 63 20

0 0 4 2 32 20 63 20

0 0 4 3 45 2D 63 2D

0 0 4 4 28 1C 63 1C

0 0 4 5 38 26 63 26

0 0 4 6 36 24 63 24

0 0 4 7 37 25 63 25

0 0 4 8 37 25 63 25

0 0 4 9 10 A 63 A

0 0 4 A 30 1E 63 1E

0 0 4 B 27 1B 63 1B

0 0 4 C 2 2 4 1

0 0 4 D 32 20 63 20

0 0 4 E 32 20 63 20

0 0 4 F 34 22 63 22

0 0 5 0 32 20 63 20

0 0 5 1 32 20 63 20

0 0 5 2 33 21 63 21

0 0 5 3 32 20 63 20

0 0 5 4 25 19 63 19

0 0 5 5 32 20 63 20

0 0 5 6 32 20 63 20

0 0 5 7 32 20 63 20

0 0 5 8 32 20 63 20

0 0 5 9 32 20 63 20

0 0 5 A 32 20 63 20

0 0 5 B 32 20 63 20

0 0 5 C 32 20 63 20

0 0 5 D 32 20 63 20

0 0 5 E 32 20 63 20

0 0 5 F 32 20 63 20

0 0 6 0 32 20 63 20

0 0 6 1 45 2D 62 25 (BUS SETUP)

0 0 6 2 46 2E 62 2A

0 0 6 3 48 30 62 30

0 0 6 4 40 28 62 28

0 0 6 5 31 1F 62 1F

0 0 6 6 31 1F 62 1F

0 0 6 7 37 25 62 25

0 0 6 8 33 21 62 21

0 0 6 9 43 2B 62 2B

0 0 6 A 43 2B 62 2B

0 0 6 B 35 23 62 23

0 0 6 C 31 1F 62 1F

0 0 6 D 31 1F 62 1F

0 0 6 E 40 28 62 28

0 0 6 F 31 1F 62 1C (BUS SETUP)

0 0 7 0 34 22 62 16 (BUS SETUP)

0 0 7 1 31 1F 62 1F

0 0 7 2 31 1F 62 1F

NVM address

EEPROM ITEMS Default Default MAX SETTING DATA

OF-TINT-ADJ

OF-SHP-N3

OF-TINT-TV

OF-TINT-AV

OFFSET_OF_COL_DVD_FIELD_FREQ_60HZ

OF-SHP-DVD

OF-SHP-P

OF-SHP-S

OF-SHP-N4

OF-COL-N4

OF-COL-N3

OF-SHP-TV

OF-SHP-AV

OF-COL-AV

OF-COL-DVD

OF-COL-P

OF-COL-S

DRI-BLW-DVD

CUT-RLW-DVD

CUT-GLW-DVD

OF-COL-TV

CUT-RLC-DVD

CUT-GLC-DVD

DRI-RLW-DVD

DRI-GLW-DVD

CUT-GLW

DRI-RLC-DVD

DRI-GLC-DVD

DRI-BLC-DVD

DRI-RLW

DRI-GLW

DRI-BLW

CUT-RLW

DRI-GLC

DRI-BLC

CUT-RLC

CUT-GLC

E/W-PAR-P60

CUT OFF

DCXO

DRI-RLC

VER-SHI-P60

VER-AMP-P60

H0R-SHI-P60

EW-W-P60

V-AMP-60

H-SHI-60

EW-W-60

E/W-PAR-60

H0R-SHI-P50

EW-W-P50

E/W-PAR-P50

V-SHI-60

VER-SHI-P50

VER-AMP-P50

4 – 3

14T1-L


0 0 7 3 32 20 63 20

0 0 7 4 15 F 60 F

0 0 7 5 10 A 60 A

0 0 7 6 14 E 60 E

0 0 7 7 16 10 60 10

0 0 7 8 10 A 60 A

0 0 7 9 16 10 60 10

0 0 7 A 30 1E 62 1E

0 0 7 B 30 1E 62 1E

0 0 7 C 30 1E 62 1E

0 0 7 D 30 1E 62 1E

0 0 7 E 24 18 62 18

0 0 7 F 36 24 62 24

0 0 8 0 60 3C 60 3C

0 0 8 1 50 32 60 32

0 0 8 2 60 3C 60 3C

0 0 8 3 30 1E 62 1E

0 0 8 4 24 18 62 18

0 0 8 5 36 24 62 24

0 0 8 6 31 1F 31 1F

0 0 8 7 48 30 63 30

0 0 8 8 1 1 63 1

0 0 8 9 10 A 32 A

0 0 8 A 5 5 7 5

0 0 8 B 25 19 63 19

0 0 8 C 31 1F 62 1F

0 0 8 D 28 1C 63 18 (BUS SETUP)

0 0 8 E 176 B0 255 B0

0 0 8 F 15 F 60 F

0 0 9 0 30 1E 255 1E

0 0 9 1 45 2D 60 2D

0 0 9 9 5 5 63 5

0 0 9 A 2 2 99 2

0 0 9 B 60 3C 60 3C

0 0 9 C 32 20 63 20

0 0 9 D 207 CF 255 CF

0 0 9 E 0 0 255 0

0 0 9 F 16 10 63 10

0 0 A 0 32 20 63 20

0 0 A 1 169 A9 255 A9

0 0 A 2 32 20 63 20

0 0 A 3 32 20 63 20

0 0 A 4 32 20 63 20

0 0 A 8 60 3C 60 3C

0 0 A 9 30 1E 60 1E

0 0 A A 30 1E 60 1E

0 0 A B 30 1E 60 1E

0 0 A C 30 1E 60 1E

0 0 B D 0 0 60 0

0 0 C 0 10 A 127 A

0 0 C 1 20 14 127 14

0 0 C 2 30 1E 127 1E

0 0 C 3 40 28 127 28

0 0 C 4 2 2 125 2

0 0 C 5 100 64 127 64

0 0 C 6 3 3 255 3

0 0 C 7 8 8 255 8

0 0 C 8 10 A 255 A

0 1 F F - - - 01 (BUS SETUP)

Default MAX SETTING DATA

FACTORY SHIPOUT LANGUAGE (MONO NTSC)

NVM address

EEPROM ITEMS Default

AVL_VOL_STEPDOWNLEVEL1


STARTMER

STOPMER

CUT-BS

CUT-BS-DVD


OPTION_HOTEL_MAX_VOL

OPTION_HOTEL_PRG

SUB-VOL

OF-SHP-LNA

FDAC_STARTMER2

OFF_CON (MONO model)

OFF_BRI (MONO model)

AV2_BRI (MONO model)

VOLUME

FDAC-VOL3

SVM2-0-NTSC

SMEL-GAIN

FDAC-VOL1

FDAC-VOL2

VER-AMP-START

OFFSET_OF_COL_DVD_FIELD_FREQ_50HZ

FTEX_ITEM_VOL5_0_OSD_60HZ

OSD-BRIGHTNESS

V-POS-OSD

H-POS-OSD

AUTO-AGC-MAX

U-CON-MOV

U-SHARP

U-SHP-NEWS

U-SHP-MOV

U-COL-NEWS

U-COL-MOV

U-PICTURE

U-CON-NEWS

U-BRIGHT

U-BRI-NEWS

U-BRI-MOV

U-COLOUR

U-BASS_MOV

U-TREBLE_MUSC

U-TREBLE_NEWS

U-TREBLE_MOV

BB-TINT

U-BASS_MUSC

U-BASS_NEWS

SHARP

PICTURE

COLOUR

BRIGHT

TINT

APRV_USER_AV_PROGRAM

APRV_FAVOURITE_KEY_RED

APRV_FAVOURITE_KEY_GREEN

APRV_FAVOURITE_KEY_YELLOW

APRV_FAVOURITE_KEY_CYAN

APRV_USER_FE_PROGRAM

4 – 4

14T1-L

D7 D6 D5 D4 D3 D2 D1 D0 (HEX) (HEX) (HEX) (HEX)

0 0 D 2 B F 7 F

0 0 D 3 7 F 9 F

0 0 D 4 7 F 7 F

0 0 D 5 7 F 7 F

0 0 D 6 8 F 7 F

0 0 D 7 3 3 5 7

0 0 D 8 D F 6 F

0 0 D 9 D F 6 F

0 0 D A 6 F 1 7

0 0 D B 7 F 3 F

0 0 D C 0 F 0 F

0 0 D D 4 F 5 F

0 0 D E 1 F 3 F

(HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX)

0 0 E 6 0 3 0 3 1 3 1 3

0 0 E 7 3 3 1 3 0 3 1 3

0 0 E 8 1 2 1 2 3 3 1 3

0 0 E 9 1 3 3 3 1 3 3 3

0 0 E A 1 3 3 3 1 3 3 3

0 0 E B 0 2 0 2 0 3 2 3

0 0 E C 0 2 0 3 1 3 1 2

0 0 E D 0 3 1 3 3 3

00

45

13

MAXDefault

D6

D6

61

77(BUS SETUP)

SETTING DATA

(HEX)

B7

7B(BUS SETUP)

77

7B(BUS SETUP)

87

35

Default MAXDefault

Default MAXDefault

MAX

MAX

Default MAX

NVM

address

EEPROM ITEMS

YD SECAM YD PAL

YD N443 YD N358

YD AV-SECAM YD AV-PAL

YD AV-N443 YD AV-N358

CL3-0 YD COMP

PW-TIME SVM2-0-PAL

WBR-50-F-C-P WBF-50-F-C-P

WBR-60-F-C-P WBF-60-F-C-P

BLOC LOUDNESS_LDS0-2

FTUN_OFFSDEM_IF (MONO model) PWLDAC

WBF-60-F-C-P (during Blue Back) WBF-50-F-C-P (during Blue Back)

LOUDNESS_LD2 (SHAKIT only) LOUDNESS_LD1 (SHAKIT only)

LOUDNESS_LD4 (SHAKIT only) LOUDNESS_LD3 (SHAKIT only)

PEAKFREQPALN PEAKFREQPALM PEAKFREQPAL443 (COR1-0) COR [FOR MONO]

PEAKFREQDVD PEAKFREQSECAM PEAKFREQNTSCM PEAKFREQNTSC443

PW-LAST AUDIO-CFG PHI H-POS-FINE

FIMG_ITEM_PRESET_WS_NEWS FIMG_ITEM_PRESET_COR_NEWS FIMG_ITEM_PRESET_WS_MUSC FIMG_ITEM_PRESET_COR_MUSC

FIMG_ITEM_PRESET_WS_CTM FIMG_ITEM_PRESET_COR_CTM FIMG_ITEM_PRESET_WS_MOV FIMG_ITEM_PRESET_COR_MOV

PRESET_SURROUND_NEWS PRESET_SURROUND_MUSC FSND_TREBLE_FREQ_SELECTION FSND_BASS_FREQ_SELECTION

RPA SOC FIMG_ITEM_AAS0_1 PRESET_SURROUND_MOV

LANGIAGE_OPTION

(MONO model) FSND_AGNE_SELECTION RPO

SETTING DATA

(HEX)

05

D1

5D

77

77

02

05

02(BUS SETUP)

4 – 5

14T1-L

(HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX) (HEX)

0 0 F 0 0 1 0 1 0 1 1 1

0 0 F 4 PWL VSD VIRGIN BPB2 FMI MUS PHI FORCE DSK-NOT-PAL-AV 1 1 0 1 1 1 1 1 0 1 0 1 1 1 0 1

0 0 F 5 DSK-NOT-PAL-DVD DSK-PAL-DVD DSK-PAL-AV BKS FSRV_ITEM_GAM BSD LCKEY-SRV-ENTER INCL-AV 0 1 0 1 0 1 1 1 1 1 0 1 1 1 1 1

0 0 F 6 FSND_ITEM_AVL_GAIN FSND_ITEM_AVL ISP AEVS_ITEM_POR ERR-VERTG ERR-SUPVOL ERR-XRAY ERR-1-8-SUP 0 1 0 1 0 1 0 1 1 1 1 1 0 1 0 1

0 0 F 7 OPTION_SMUTE_L FTUN_TUNER_CP FSRV_ITEM_TFR OPTION_HOTEL FSND_LOUDNESS_HIGH_BOOST DTR AGN DSG 0 1 1 1 0 1 0 1 1 1 1 1 1 1 1 1

0 0 F 8DMP50

(Mono model)

CB

(Mono model)

DSGLS

(Mono model) CBS 0 1 1 1 0 1 1 1

0 0 F A AUTO SELECT M.P. IN BLUE BACK LAST POWER LOCK TV AVL ENERGY SAVE PICTURE NR 1 1 1 1 1 1 1 1 0 1 1 1 0 1 0 1

0 0 F BPICTURE NR

(NEWS)

PICTURE NR

(MOVIE) DAC_MODE VIRGIN S_BOOSTER LOUDNESS 0 1 0 1 0 1 1 1 1 1 1 1

AIR/CABLE SURROUND (MOVIE)

Default MAX Default MAX Default MAXDefault MAXDefault MAX Default MAX Default MAX Default MAX

7

1

1B

4C (BUS SETUP)

4F

05

F4

B2

(HEX)

SETTING DATA

4 – 6

14T1-L
TV14T1-LService Manual14T1-LMarketE CHAPTER 5. ADJUSTMENT METHOD
[1] ADJUSTMENT METHOD

ADJUSTMENT PRECAUTIONS

This model's setting are adjusted in two different ways: through the I2C bus control and in the

conventional analog manner. The adjustments via the I2C bus control include preset-only items and

variable data.

1. Setting the service mode by the microprocessor.

(a) Press and hold the local key "VOL DOWN" & "CH UP" and power on the main switch,

TV will enter into the SERVICE MODE. Or Key in service key of 40 (HEX) will enter the

service mode. The initial value of EEPROM are automatically preset when new EEPROM

is used. However, after the 1st time it will not be able to preset unless do the precedure

in section 2 as below.

(b) Press the CH DOWN / UP key on the remote controller to select the setting items

one by one.

(c) Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.

(d) When press the local key "VOL DOWN" & "CH UP" at the same time or press service

key 40 (HEX), it will be released from the service mode.

2. Factory Presetting.

(1) Press remote controller key of code "B7" for 4 seconds, the initial values are

automatically preset.

(2) The initial data are preset as listed in page 2 until 7.

(3) Please modify the bus setup data.

Precaution: If haven't done this initialization, malfunction might be happen.

3. For reference, please check with memory map RH-IXC227WJZZQ (See Attachment)

5 – 1

14T1-L

There is three stage of Service Mode data

First stage data from V01 ~ V35

to go into second stage of service mode data, press MENU key

Second stage data from 008 ~ 1FF

Below is the contents of these data

Adjustment Mode Items

01 RF-AGC 0…63 UOC-TV 23 23

02 V-SLOPE 0…63 UOC-TV 31 31

03 S-COR 0…63 UOC-TV 16 16

04 DRI-RS 0…63 UOC-TV 32 32

05 DRI-GS 0…63 UOC-TV 32 32

06 DRI-BS 0…63 UOC-TV 32 32

07 CUT-RS 0…63 UOC-TV 16 16

08 CUT-GS 0…63 UOC-TV 16 16

09 CUT-BS 0…63 UOC-TV 16 16

10 SUB-BRI 0…63 UOC-TV 32 32

11 SUB-CON 0…63 UOC-TV 25 45 (BUS SETUP)

12 SUB-COL 0…63 UOC-TV 10 10

13 SUB-TINT 0…63 UOC-TV 36 36

14 SUB-SHARP 0…63 UOC-TV 32 32

15 DRI-RW 0…63 UOC-TV 38 38

16 DRI-GW 0…63 UOC-TV 32 32

17 DRI-BW 0…63 UOC-TV 19 19

18 DRI-RLW 0…63 UOC-TV 33 33

19 DRI-GLW 0…63 UOC-TV 32 32

20 DRI-BLW 0…63 UOC-TV 25 25

21 DRI-RC 0…63 UOC-TV 32 32

22 DRI-GC 0…63 UOC-TV 32 32

23 DRI-BC 0…63 UOC-TV 37 37

24 DRI-RLC 0…63 UOC-TV 32 32

25 DRI-GLC 0…63 UOC-TV 32 32

26 DRI-BLC 0…63 UOC-TV 34 34

27 V-SHI-60 0…63 UOC-TV 32 32

28 V-AMP-60 0…63 UOC-TV 32 32

29 H-SHI-60 0…63 UOC-TV 45 45

30 VSD 0/1 UOC-TV 0 0

31 CUT OFF 0…63 UOC-TV 27 27

32 DCXO 0…4 UOC-TV 2 1

33 ISP MODE 0/1 UOC-TV 0 0

34 BLOC 0…15 UOC-TV 6 6

35 SUB-VOL 0…60 UOC-TV 60 60

Setting Data (DEC)Item

Setting Item Setting Range DefaultIC

5 – 2

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

MAX - 0.1V dc

SYMBOL

RF INPUT

FIELD STRENGTH 56dBµV(FIX)

TUNER AGC TERMINAL (JA352) OR CRT DISPLAY CONFIRMATION

(AT SELF ADJUSTMENT MODE)

1.GO TO SERVICE MODE

2.GO TO SERVICE DATA "RF-AGC" ITEM IN THE ADJUSTMENT, PRESS R/C TO OPERATE AUTO-

AGC KEY AND CONFIRM THE OK DISPLAY ON THE SCREEN .

3.BLUE DISPLAY WITH OK SIGN INDICATES THE ADJUSTMENT IS WORKING PROPERLY.

(AT MANUAL ADJUSTMENT MODE)

[CHECKING CONFIRMATION ]

14T1-L

I2C CONTROL

BUS SET UP

US10CH HALF COLOR BAR

RF-AGC

01 STEP RANGE 0-63

HISTORY

OF REVISIONREVISED CONTENT .

MODEL NAME

1. SELECT "RF-AGC" ITEM IN THE ADJUSTMENT MODE. ADJUST THE "RF-AGC" BUS

DATA TO OBTAIN THE TUNER OUTPUT PIN DROP 0.1V~1.0V BELOW MAXIMUM

VOLTAGE.

2. CHANGE THE ANTENNA INPUT SIGNAL TO 63~67 dBuV, AND MAKE SURE THERE IS NO

NOISE

3. CHANGE THE ANTENNA INPUT SIGNAL TO 90~95 dBuV TO BE SURE THAT THERE IS NO

CROSS MODULATION BEAT.

5 – 3

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

SYMBOL

AC 220 V, RF INPUT, ZERO MAGNETIC FIELD

CRT DISPLAY CONFIRMATION

ADJUST THE V-SLOPE BUS DATA UNTILL THE OVERSCAN BECOME AS SPECIFIED BELOW.

CAUTION:- PLEASE AGING TV MORE THAN 10 MINUTES BEFORE ADJUSTMENT.


14T1-L

I2C CONTROL

BUS SET UP,CRT PURITY

US 4 CH LION HEAD

V-SLOPE

02 STEP RANGE 0~63

HISTORY


MODEL NAME

A = Out of spec

B = OK

C = Out of spec

5 – 4

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTOROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

SYMBOL



ADJUST V-SHIFT BUS DATA TO HAVE A MOST ACCEPTABLE VERTICAL POSITION.

THE MONOSCOPE PATTERN SHOULD BE BALANCE IN VERTICAL POSITION


14T1-L

I2C CONTROL

BUS SET UP, CRT PURITY, V-SLOPE

US 4 CH LION HEAD (MONOSCOPE PATTERN)

V-SHIFT-60

27 STEP RANGE 0-63

HISTORY

OFREVISIONREVISED CONTENT .

MODEL NAME

5 – 5

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

SYMBOL

ADJUST THE V-AMP-60 BUS DATA UNTILL THE OVERSCAN BECOME AS SPECIFIED BELOW.


OVERSCAN 10 ± 2.5%

HISTORY


BUS SET UP,CRT PURITY, V-SLOPE, V-SHIFT 60




28 STEP RANGE 0~63

I2C CONTROL

MODEL NAME 14T1-L

V-AMP-60

5 – 6

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

LEFT AND RIGHT SYMMETRICAL

SYMBOL

I2C BUS CONTROL

BUS SET UP,CRT-PURITY

MODEL NAME

H-SHIFT-60

STEP RANGE29 0-63

14T1-L


1.ADJUST THE H-SHIFT BUS DATA TO HAVE A BALANCE POSITION TO SPEC OF A=B


CONFIRMATION BY CRT SCREEN

HISTORY


US 4 CH LION HEAD (MONOSCOPE)

BA

5 – 7

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

SYMBOL

MODEL NAME

CRT CUT OFF ADJUSTMENT

30 (VSD) STEP RANGE -

14T1-L

I2C CONTROL

BUS SET UP

AV MODE (WITHOUT SIGNAL) WITH BLUEBACK OFF

AC 220 V, AV INPUT

CONFIRMATION ON CRT DISPLAY.


1) IN SERVICE MODE, SET CUT OFF TO 27, SUB-CON TO 45, SUB-BRI TO 32 AND DRI-RS, DRI-RS&

DRI-BS TO 32; CUT-RS, CUT-GS & CUT-BS TO 16 , SWITCH TV TO VIDEO MODE, BLUE BACK OFF,

WITHOUT SIGNAL.

2) GO TO ADJUSTMENT MODE ITEM VSD AND PRESS VOLUME UP AT R/C. ADJUST THE SCREEN

VR OF FBT SO THAT CUT-OFF LINE APPEAR IN LOW BRIGHT, THEN JUDGE THAT WHETHER THE

CUT-OFF LINE APPEAR IN RED OR GREEN OR BLUE COLOR. FIX THE CUT OFF DATA OF THE

COLOR APPEAR IN CUT-OFF LINE AND USE R/C TO ADJUST THE OTHER TWO AMONG CUT-RS,

CUT-GS & CUT-BS UNTIL COLOUR BECOME WHITE.

3)TURN THE SCREEN VR OF FBT SO THAT CUT-OFF LINE JUST DISAPPEAR.

HISTORY


5 – 8

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

SYMBOL

MODEL NAME

WHITE BALANCE

4,5,6,7,8,9 STEP RANGE 0~63

14T1-L

I2C BUS CONTROL

BUS SET UP,CRT PURITY, SCREEN

AV; W/B PATTERN 1 (PATTERN GENERATOR SX- 1006)

AC 220 V, AV INPUT


1)WHITE (HIGH BEAM)

FIRST LET THE GUN POINT AT WHITE POSITION (AS DRAWING ATTACH), ADJ THE

PATTERN GENERATOR UPPER VR UNTIL Y BECOME 150 cd/m2. AFTER THAT, LET THE

GUN POINT AT WHITE POSITION AGAIN AND ADJUST THE BUS DATA OF DRI-RS AND

DRI-BS UNTLL THE AXIS OF COLOUR TEMPERATURE BECOME X=0.273,Y=0.280.

2)DARK(LOW BEAM)

LET THE GUN POINT AT DARK POSITION (AS DRAWING ATTACH),ADJUST THE

PATTERN GENERATOR LOWER VR UNTIL Y BECOME 5 cd/m2. ADJUST THE TWO

SERVICE DATA (AMONG CUT-RS, CUT-GS AND CUT-BS) WHICH HAVE CHOSEN AT CUT

OFF ADJUSTMENT SO THAT TO OBTAIN THE SIMILAR AXIS OF COLOUR TEMPERATURE

AS ABOVE.

*FOR ADJUSTMENT IN 1 & 2, MUST ALWAYS MAINTAIN THE Y AT 150cd/m2 (WHITE) AND

AT 5cd/m2 (DARK) WITH ADJUSTING THE UPPER AND LOWER VR OF PATTERN

GENERATOR.

**REPEAT STEP 1),2) TO GET A REGULATED LEVEL.


X=0.273,Y=0.280 (11,600° K+1 MPCD)

HISTORY


WHITEDARK

5 – 9

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

SYMBOL REVISED CONTENT .HISTORY

OF REVISION


I2C CONTROL

BUS SET UP, CUT OFF, WHITE BALANCE

AV; WINDOW PATTERN (PATTERN GENERATOR SX- 1006)

AC 220 V, AV INPUT

MODEL NAME

BLOC

34 STEP RANGE 0~15

14T1-L


1)LET THE GUN POINT AT BLACK POSITION(AS ATTACH DRAWING), ADJUST BLOC BUS DATA

UNTIL LUMINANCE Y = 0.43cd/m2+ 0.1

BLACK

5 – 10

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

SYMBOL

MODEL NAME

SUB COLOUR

12 STEP RANGE 0~63

14T1-L

I2C BUS CONTROL

BUS SET UP, RF-AGC, CUT OFF, WHITE BALANCE

US 10 CH HALF COLOR BAR PATTERN

AC 220 V, RF INPUT

R-AMP TR BASE (JA801 OR TP851)

CONFIRM WITH OSCILLOSCOPE

1)CONNECT THE OSCILLOSCOPE TO TP 851 RED TO OBTAIN WAVEFORM AS BELOW.

2)ADJUST THE 100% WHITE & RED PORTIONS OF COLOR BAR UNTIL THE SAME LEVEL


HISTORY


W Y

Cy G

100% WHITE

Mg R B

5 – 11

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

SYMBOL

MODEL NAME

SUB-TINT

13 STEP RANGE 0~63

14T1-L

I2C CONTROL

BUS SET UP, RF-AGC, CUT OFF, WHITE BALANCE, SUB-COLOUR

US 10 CH HALF COLOR BAR PATTERN

AC 220 V, RF INPUT

B-AMP TR BASE (JA810 OR TP853)

CONFIRRM WITH OSCILLOSCOPE

1)RECEIVE THE US 10 CH HALF COLOR BAR PATTERN.

2)CONNECT THE OSCILLOSCOPE TO TP 853 BLUE OUT.


HISTORY


Range : 100mV/ Div USE PROBE 10:1

SWEEP TIME : 10 usec/Div

3) SELECT THE "SUB-TINT" ITEM IN THE ADJUSTMENT MODE. ADJUST THE "SUB-TINT" DATA

TO OBTAIN THE WAVEFORM AS SHOWN AS BELOW (W & MG SAME LEVEL)

G

G Mg R BY CyW

5 – 12

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

MODEL

14T1-L

SYMBOL

MODEL NAME

X-RAY PROTECTION OPERATING CONFIRMATION

STEP RANGE

14T1-L

AC 220V, RF INPUT

CONFIRMATION BY THE CRT


[VOLTAGE CONFIRMATION]

CHECK THE VOLTAGE OF C602 +VE TERMINAL AS SPECIFIED BELOW.

[OPERATION CONFIRMATION]

SUPPLY THE DC VOLTAGE (27V AS BELOW) TO C602 +VE TERMINAL AND MAKE SURE THE

PROTECTOR IS FUNCTIONED , HORIZONTAL OSCILATION STOP AND PICTURE DISAPPEAR.

[RECOVER INFORMATION]

PULL OUT THE AC CORD .

[CAUTION]

FROM THE RECOVER CONFIRMATION MENTIONED ABOVE,THE AC CODE MUST BE PULLED

OUT AT LEAST 5 SECONDS BEFORE PLUGGING IN AGAIN. (IN ORDER TO MAKE SURE THE -

CON HAS BEEN RESET.)

27V

HISTORY


TP VOLTAGE

20.6 ± 1.1V DC

PROTECTOR OPERATION VOLTAGE

AFTER ALL ADJUSTMENT FINISHED.


5 – 13

14T1-L

ADJUSTMENT

ITEM

ADJUSTMENT

POSITION

CONTROL

PRE-ADJUST

REQUIREMENT

CONTENT

INPUT

CONDITION

OUTPUT

ADJUSTMENT

PROCEDURE

MODEL

14T1-L

SYMBOLHISTORY



CRT ANODE VOLTAGE

CONFIRM THE VOLTAGE OF CRT ANODE BY HIGH VOLTAGE METER AND MAKE SURE THE

READING IS AS BELOW.

HIGH VOLTAGE

BELOW 25.5kV

AFTER ALL ADJUSTMENT FINISHED.


AC 220V, RF INPUT

MODEL NAME 14T1-L

HIGH VOLTAGE

STEP RANGE

5 – 14

14T1-L

6 – 1

TV14T1-LService Manual14T1-LMarketE CHAPTER 6. WAVEFORMS

[1] WAVEFORMS

(1) 1.79 Vp-p (H) (2) 2.85 Vp-p (H) (3) 2.42 Vp-p (H) (4) 2.75 Vp-p (H)

(5) 2.60 Vp-p (H) (6) 6.00 Vp-p (H) (7) 1.06 Vp-p (V) (8) 1.32 Vp-p (H)

(9) 39.30 Vp-p (H) (10) 1190.0 Vp-p (H) (11) 52.10 Vp-p (V) (12) 2.20 Vp-p (v)

(13) 121.40 Vp-p (H) (14) 477.0 Vp-p (15) 4.90 Vp-p (V) (16) 83.60 Vp-p (H)

(17) 57.80 Vp-p (H) (18) 82.2 Vp-p (H) (19) 1.91 Vp-p (V)

WAVEFORMS

14T1-L

7 – 1

TV14T1-LService Manual14T1-LMarketE CHAPTER 7. CHASSIS LAYOUT

[1] CHASSIS LAYOUT

14T1-L
TV14T1-LService Manual14T1-LMarketE CHAPTER 8. BLOCK DIAGRAM
[1] BLOCK DIAGRAM: MAIN UNIT

A

C

B

D

E

F

G

H

2 1098765431

8 – 1

14T1-L

19181716151413121110

8 – 2

14T1-L
[2] BLOCK DIAGRAM: CRT UNIT
8 – 3

14T1-L

9 – 1

TV14T1-LService Manual14T1-LMarketE CHAPTER 9. DESCRIPTION OF SCHEMATIC DIAGRAM

[1] DESCRIPTION OF SCHEMATIC DIAGRAM

DESCRIPTION OF SCHEMATIC DIAGRAM

NOTES:

1. The unit of resistance "ohm" is omitted.

(K=kΩ=1000Ω, M=MΩ)

2. All resistors are 1/16 watt, unless otherwise noted.3. All capacitors are µF, unless otherwise noted.

(P=pF=µµF)

4. (G) indicates ±2% tolerance may be used.

5. indicates line isolated ground.

VOLTAGE MEASUREMENT CONDITIONS:

1. All DC voltages are measured with DVM connected

between points indicated and chassis ground, line

voltage set at 120V AC and all controls set for normal

picture unless otherwise indicated.

2. All voltages measured with 1000µ V B & W or Color

signal.

WAVEFORM MEASUREMENT CONDITIONS:

1. Photographs taken on a standard gated color bar

signal, the tint setting adjusted for proper color. The

wave shapes at the red, green and blue cathodes of

the picture tube depend on the tint, color level and

picture control.

2. indicates waveform check points (See chart,waveforms are measured from point indicated to

chassis ground.)

AND SHADED ( ) COMPONENTS

= SAFETY RELATED PARTS.

MARK= X-RAY RELATED PARTS.

DRGANNESMARQUES ETHACHRES ( ):

PIECES RELATIVES A LA SECURITE.MARQUE : PIECS RELATIVE AUX RAYONS X.

This circuit diagram is a standard one, printed circuits

may be subject to change for product improvement

without prior notice.

14T1-L
TV14T1-LService Manual14T1-LMarketE CHAPTER 10. SCHEMATIC DIAGRAMS
[1] SCHEMATIC DIAGRAM: MAIN UNIT

10 – 1

14T1-L

10 – 2

14T1-L
[2] SCHEMATIC DIAGRAM: CRT UNIT
10 – 3

14T1-L
TV14T1-LService Manual14T1-LMarketE CHAPTER 11. PRINTED WIRING BOARD ASSEMBLIES
[1] PWB-A: MAIN UNIT (Wiring Side)

11 – 1

14T1-L
[2] PWB-A: MAIN UNIT (Chip Parts Side)
11 – 2

14T1-L
[3] PWB-B: CRT UNIT (Wiring Side)
11 – 3

14T1-L
[4] PWB-B: CRT UNIT (Chip Parts Side)
11 – 4

14T1-L
PartsGuide
PARTS GUIDENo. XXXXXXXXXXXX

XXXXXXXXMODEL

CONTENTS

14T1-L

S878314T1L

[1] PICTURE TUBE

[2] PRINTED WIRING BOARD ASSEMBLIES

[3] MAIN UNIT

[4] CRT UNIT

[5] SUPPLIED ACCESSORIES

[6] CABINET PARTS

[7] PACKING PARTS

INDEX

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace theseparts with specified ones for maintaining the safety and performance of the set.

This document has been published to be usedfor after sales service only.The contents are subject to change without notice.

14T1-L

PRICE NEW PART DELIVERY
NO. PARTS CODE RANK MARK DESCRIPTION
[1] PICTURE TUBE! VB370BVBK1S9E R SEMI-ITC Picture Tube! RCILGA114WJZZ R Degaussing Coil

QEARC1422PEZZ R Ground-PartPMAGF3045CEZZ R Magnet

[2] PRINTED WIRING BOARD ASSEMBLIESDUNTKE161WEA1 - - MAIN UnitDUNTKE162WEA1 - - CRT Unit

[3] MAIN UNIT! TU201 RTUNQA037WJZZ R Tuner

IC301 VHILA42031E-1 R LA4203E-1! IC501 VHISTV9302B-1 R STV9302B! IC701 VHISTRW5453-1 AM R I.C.

IC801 RH-IXC227WJZZQ R I.C.IC1003 VHIBR24L08F-1Y AE R BR24L08F-WE2

Q201 VS2SC2735//1EY R 2SC2735//1EQ302 VS2SA1530AR-1Y AB R 2SA1530ARQ601 VS2SC2235Y/1E+ AE R 2SC2235Q602 VSTT2140+++-F AG R TT2140Q603 VS2SC3198-G-1+ AA R 2SC3198Q751 VS2SD468-C/-1+ AD R 2SD468Q754 VS2SC3198-G/-1+ AD R 2SC3198Q755 VS2SC3198-G/-1+ AD R 2SC3198Q801 VS2SC3928AR-1Y AB R 2SC3928ARQ803 VS2SC3928AR-1Y AB R 2SC3928AR

Q1070 VS2SC3928AR-1Y AB R 2SC3928ARD201 VHEZJ33C+++1EY AA R Zener Diode , 33VD203 VHDHSS4148+-1Y AA R DiodeD204 VHDHSS4148+-1Y AA R DiodeD301 VHEZJ12B+++1EY AA R DiodeD302 VHDHSS4148+-1Y AA R DiodeD303 VHDHSS4148+-1Y AA R DiodeD393 RH-DX0302CEZZ AE R Diode , DX0302CED503 RH-EX0612GEZZY AB R Zener Diode , 5.1VD505 RH-DX0441CEZZY AC R Diode , DX0441CED510 RH-DX0131CEZZY AC R Diode , DX0131CED511 RH-DX0131CEZZY AC R Diode , DX0131CED602 VHD1SS244//-1Y AB R Diode , 1SS244D603 VHEZJ27B+++1EY AA R Zener Diode , 27VD605 VHDHSS4148+-1Y AA R DiodeD606 RH-DX0131CEZZY AC R Diode , DX0131CED607 VHDHSS4148+-1Y AA R DiodeD608 VHEZJ5R6B++1EY AA R Zener Diode , 5.6V

! D701 RH-DX0476CEZZ AG R Diode , DX0476CED706 RH-DX0066GEZZY AC R Diode , DX0066GED707 RH-DX0066GEZZY AC R Diode , DX0066GED709 RH-DX0066GEZZY AC R Diode , DX0066GED710 VHDHSS4148+-1Y AA R DiodeD715 VHEZJ5R6B++1EY AA R Zener Diode , 5.6VD720 RH-DX0131CEZZY AC R Diode , DX0131CED721 RH-DX0066GEZZY AC R Diode , DX0066GED722 VHEZJ27D+++1EY AA R Zener Diode , 27VD723 VHEZJ12B+++1EY AA R Zener Diode , 12.03VD724 VHEZJ4R3B++1EY R Zener Diode , 4.3VD725 VHDHSS4148+-1Y AA R DiodeD732 VHEZJ8R2A++1EY AB R Zener Diode , 8.2VD736 VHEZJ36C+++1EY AB R Zener Diode , 36VD751 RH-DXA044WJZZ R Diode , DXA044WJD752 RH-DX0247CEZZ AE R Diode , DX0247CED754 VHEZJ5R1A++1EY R Zener Diode , 5.1VD758 VHEZJ3R3A++1EY R Zener Diode , 3.3VD759 VHDHSS4148+-1Y AA R DiodeD760 VHEZJ8R2B++1EY AB R Zener Diode , 8.2VD764 VHDHSS4148+-1Y AA R DiodeD801 RH-EX0277TAZZY AA R Zener DiodeD802 RH-EX0277TAZZY AA R Zener DiodeD803 RH-EX0277TAZZY AA R Zener DiodeD804 VHDHSS4148+-1Y AA R DiodeD805 VHDHSS4148+-1Y AA R DiodeD806 RH-EX1393CEZZY AB R Zener Diode , 5.1VD807 VHEZJ5R1B++1EY AC R Zener Diode , 5.1VD808 VHEZJ12B+++1EY AC R Zener Diode , 12V

D1001 RH-PX0013PEZZ AC R PhotodiodeD1003 RH-EX1393CEZZY AB R Zener Diode , 5.1VD1004 RH-EX1393CEZZY AB R Zener Diode , 5.1VD1005 VHDHSS4148+-1Y AA R DiodeD1007 VHDHSS4148+-1Y AA R DiodeD1008 VHDHSS4148+-1Y AA R DiodeVA701 RH-VXA182WJZZ R Varistor

X801 RCRSAA058WJZZ R CrystalL203 VP-DF270K0000Y AB R Peaking 27mHL204 VP-XF1R2K0000Y AB R Peaking 1.2mHL205 VP-XF2R7K0000Y AB R Peaking 2.7mH

2

14T1-L

NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
L701 RCILFA187WJZZ AD R CoilL802 VP-XF4R7K0000Y AB R Peaking 4.7mHL804 VP-DF100K0000Y AB R Peaking 10mHL805 VP-DF100K0000Y AB R Peaking 10mHL807 VP-DF100K0000Y AB R Peaking 10mHL808 VP-XF100K0000Y AB R Peaking 10mHL809 VP-XF100K0000Y AB R Peaking 10mHL810 VP-XF100K0000Y AB R Peaking 10mHL812 VP-XF4R7K0000Y AB R Peaking 4.7mHL813 VP-XF4R7K0000Y AB R Peaking 4.7mH

SF201 RFILCA055WJQZS R CoilT602 RTRNFA140WJZZ R H-Volt TransformerT603 RTRNZA058WJZZ AD R TransformerT702 RTRNWA287WJZZ R TransformerC202 VCEA0A1AW108M+ AC R 1000 10V ElectrolyticC203 VCKYCY1HF103ZY AA R 0.01 50V CeramicC206 VCEA0A1HW106M+ AB R 10 50V ElectrolyticC207 VCKYCY1HB103ZY AA R 0.01 50V CeramicC208 VCKYCY1HB103ZY AA R 0.01 50V CeramicC209 VCKYCY1HB103ZY AA R 0.01 50V CeramicC210 VCKYCY1HB103ZY AA R 0.01 50V CeramicC211 VCEA0A1HW475M+ AB R 4.7 50V ElectrolyticC301 VCEA0A1EW476M+ AB R 47 25V ElectrolyticC304 VCEA0A1HW105M+ AB R 1 50V ElectrolyticC305 VCKYCY1HB153KY AA R 0.15 50V CeramicC306 VCEA0A1CW336M+ AB R 33 16V ElectrolyticC307 VCEA0A1AW108M+ AC R 1000 10V ElectrolyticC308 VCEA0A1EW477M+ AD R 470 25V ElectrolyticC309 VCFYFA1HA474J+ AE R 0.47 50V MylarC314 VCEA0A1HW475M+ AB R 4.7 50V ElectrolyticC370 VCEA0A1CW106M+ AB R 10 16V ElectrolyticC372 VCE9GA1HW225M+ AB R 2.2 50V ElectrolyticC383 VCEA0A1CW106M+ AB R 10 16V ElectrolyticC391 VCKYPA1HB102K+ AA R 1000p 50V CeramicC393 VCEA0A1EW108M+ AD R 1000 25V ElectrolyticC395 VCE9GA1HW225M+ AB R 2.2 50V ElectrolyticC451 VCEA0A1CW477M+ AC R 470 16V ElectrolyticC505 VCEA0A1HW107M+ AB R 100 50V ElectrolyticC508 VCFYAA2AA224J+ AD R 0.22 100V MylarC511 VCEA0A1VW477M+ AB R 470 35V ElectrolyticC512 VCKYPA2HB102K+ AA R 1000p 500V CeramicC515 VCKYPA2HB102K+ AA R 1000p 500V CeramicC516 VCEA0A1CW477M+ AC R 470 16V ElectrolyticC601 VCQYTA1HM563J+ AB R 0.56 50V MylarC602 VCEA0A1HW475M+ AB R 4.7 50V ElectrolyticC604 VCEA0A2EW336M+ AD R 33 250V ElectrolyticC606 VCKYPA2HB102K+ AA R 1000p 500V CeramicC607 VCFPVC3ZA612H AD R 6.1 1.8KV Metalized Polypro FilmC608 VCQYTA1HM472J+ AB R 4.7 50V MylarC611 VCFPVC2EB334J AD R 0.33 200V Metalized Polypro FilmC650 VCKYPA2HB101K+ AB R 100p 500V CeramicC701 RC-FZ032SCEZZ AD R 220 275V Metalized Plastic FilmC702 RC-KZ0029CEZZ+ AC R 0.01 250V CeramicC703 RC-KZ0029CEZZ+ AC R 0.01 250V CeramicC704 RC-KZ0029CEZZ+ AC R 0.01 250V CeramicC705 RC-EZA095WJZZ AM R 220 400V ElectrolyticC706 VCFYFA1HA105J+ AE R 1 50V MylarC708 VCKYPA1HB221K+ AB R 220p 50V CeramicC709 VCQYTA1HM103J+ AB R 0.01 50V MylarC710 VCQYTA1HM222J+ AB R 2.2 50V MylarC711 VCKYPA1HB222K+ AB R 2200p 50V CeramicC713 RC-KZ0102GEZZ AC R 2kV CeramicC719 VCEA0A1HW476M+ AB R 47 50V ElectrolyticC720 VCKYPA2HB102K+ AA R 1000p 500V CeramicC721 VCEA0A1CW477M+ AC R 470 16V ElectrolyticC722 VCEA0A1CW476M+ AC R 47 16V ElectrolyticC750 VCKYPA2HB102K+ AA R 1000p 500V CeramicC752 VCKYPH3DB561K AC R 560p 2KV CeramicC753 RC-EZA235WJZZ AD R 100 160V ElectrolyticC754 RC-EZA522WJZZ AD R 33 160V ElectrolyticC756 VCEA0A1EW228M+ AE R 2200 25V ElectrolyticC758 VCEA0A1AW107M+ AB R 100 10V ElectrolyticC759 VCKYCY1HB104KY AA R 0.1 50V CeramicC784 VCKYPH3DB561K AC R 560p 2KV CeramicC808 VCEA0A1HW475M+ AB R 4.7 50V ElectrolyticC809 VCKYCY1HB104KY AA R 0.1 50V CeramicC810 VCEA0A1CW106M+ AB R 10 16V ElectrolyticC812 VCKYCY1HB104KY AA R 0.1 50V CeramicC815 VCKYCY1HB104KY AA R 0.1 50V CeramicC816 VCEA0A1CW476M+ AB R 47 16V ElectrolyticC817 VCKYCY1HB103KY AA R 0.01 50V CeramicC818 VCEA0A1CW476M+ AB R 47 16V ElectrolyticC820 VCKYCY1AB105KY AA R 1 10V CeramicC822 VCKYCY1AB105KY AA R 1 10V CeramicC825 VCEA0A1HW475M+ AB R 4.7 50V Electrolytic

[3] MAIN UNIT

3

14T1-L

C826 VCKYCY1HB104KY AA R 0.1 50V CeramicC827 VCEA0A1CW106M+ AB R 10 16V ElectrolyticC828 VCKYCY1HB104KY AA R 0.1 50V CeramicC829 VCEA0A1CW106M+ AB R 10 16V ElectrolyticC830 VCKYCY1HB104KY AA R 0.1 50V CeramicC831 VCEA0A1CW106M+ AB R 10 16V ElectrolyticC832 VCKYCY1HB103KY AA R 0.01 50V CeramicC833 VCEA0A1CW106M+ AB R 10 16V ElectrolyticC835 VCFYFA1HA154J+ AA R 0.15 50V MylarC836 VCKYCY1HB102KY AA R 1000p 50V CeramicC837 VCKYCY1HB102KY AA R 1000p 50V CeramicC839 VCKYCY1HB223KY AA R 0.22 50V CeramicC840 VCFYFA1HA224J+ AA R 0.22 50V MylarC841 VCQYTA1HM682J+ AB R 6.8 50V MylarC842 VCKYCY1AB105KY AA R 1 10V CeramicC843 VCEA0A1HW475M+ AB R 4.7 50V ElectrolyticC844 VCFYFA1HA103J+ AA R 0.01 50V MylarC845 VCKYCY1CF224ZY AB R 0.22 16V CeramicC846 VCEA0A1AW107M+ AB R 100 10V ElectrolyticC847 VCEA0A1CW106M+ AB R 10 16V ElectrolyticC848 VCKYCY1HB104KY AA R 0.1 50V Ceramic

C1001 VCEA0A1AW107M+ AB R 100 10V ElectrolyticC1003 VCEA0A1CW106M+ AB R 10 16V ElectrolyticC1004 VCKYCY1CF474ZY AB R 0.47 16V CeramicC1005 VCCCCY1HH101JY AA R 100p 50V CeramicC1016 VCKYCY1EF104ZY AA R 0.1 25V CeramicC1081 VCFYFA1HM104J+ AA R 0.1 50V MylarC1852 VCKYCY1HF224ZY AA R 0.22 50V CeramicC1853 VCEA0A1HW104M+ AB R 0.1 50V ElectrolyticC1859 VCEA0A1HW106M+ AB R 10 50V Electrolytic

RJ14 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ17 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ22 VRS-CY1JF000JY AA R 0 1/16W Metal OxideRJ23 VRS-CY1JF000JY AA R 0 1/16W Metal OxideR201 VRD-RA2BE101JY AA R 100 1/8W CarbonR202 VRD-RA2BE101JY AA R 100 1/8W CarbonR205 VRS-CY1JF680JY AA R 68 1/16W Metal OxideR206 VRS-CY1JF272JY AA R 2.7K 1/16W Metal OxideR207 VRS-CY1JF221JY AA R 220 1/16W Metal OxideR208 VRS-CY1JF221JY AA R 220 1/16W Metal OxideR209 VRS-CY1JF392JY AA R 3.9K 1/16W Metal OxideR213 VRS-CY1JF103JY AA R 10K 1/16W Metal OxideR214 VRS-CY1JF563JY AA R 56K 1/16W Metal OxideR216 VRS-RG3LB393J+ AC R 39K 3W Metal FilmR220 VRS-CY1JF221JY AA R 220 1/16W Metal OxideR301 VRD-RA2BE822JY AA R 8.2 1/8W CarbonR303 VRS-CY1JF473JY AA R 47K 1/16W Metal OxideR304 VRD-RA2BE223JY AA R 22K 1/8W CarbonR305 VRS-CY1JF274JY AA R 270K 1/16W Metal OxideR314 VRS-CY1JF561JY AA R 560 1/16W Metal OxideR315 VRS-CY1JF122JY AA R 1.2K 1/16W Metal OxideR322 VRS-CY1JF104JY AA R 100K 1/16W Metal OxideR323 VRD-RA2BE101JY AA R 100 1/8W CarbonR324 VRS-CY1JF102JY AA R 1K 1/16W Metal OxideR325 VRD-RM2HD1R0JY AA R 1 1/2W CarbonR365 VRS-CY1JF103JY AA R 10K 1/16W Metal OxideR366 VRS-CY1JF682JY AA R 6.8K 1/16W Metal OxideR372 VRS-CY1JF103JY AA R 10K 1/16W Metal OxideR383 VRS-CY1JF103JY AA R 10K 1/16W Metal OxideR384 VRS-CY1JF682JY AA R 6.8K 1/16W Metal OxideR391 VRN-RL3ABR10J+ AA R 10 1W Metal FilmR431 VRD-RA2BE151JY AA R 150 1/8W CarbonR432 VRS-CY1JF221JY AA R 220 1/16W Metal OxideR458 VRS-CY1JF103JY AA R 10K 1/16W Metal OxideR459 VRD-RA2EE750JY AA R 75 1/4W CarbonR461 VRS-CY1JF750JY AA R 75 1/16W Metal OxideR462 VRS-CY1JF151JY AA R 150 1/16W Metal OxideR503 VRN-RL3DB2R7J+ AB R 2.7 2W Metal FilmR506 VRS-RG3AB331J+ AB R 330 1W Metal OxideR507 VRD-RM2HD1R0JY AA R 1 1/2W CarbonR508 QJUM-0001AJFWY R Jumper wireR509 QJUM-0001AJFWY R Jumper wireR513 VRS-CY1JF222JY AA R 2.2K 1/16W Metal OxideR515 VRS-CY1JF183JY AA R 18K 1/16W Metal OxideR520 VRS-CY1JF272JY AA R 2.7K 1/16W Metal OxideR601 VRS-VV3AB121J AA R 120 2W Metal OxideR602 VRD-RA2BE393JY AA R 39K 1/8W CarbonR603 VRD-RA2BE273JY AA R 27K 1/8W CarbonR604 VRD-RA2BE563JY AA R 56K 1/8W CarbonR605 VRD-RM2HD154JY AA R 150K 1/2W CarbonR606 VRN-RL3LBR18J+ AD R 18 3W Metal FilmR607 VRS-VV3AB101J AA R 100 2W Metal OxideR608 VRN-RL3LBR22J+ AD R 22 3W Metal FilmR609 VRD-RM2HD270JY AA R 27 1/2W CarbonR611 VRN-RL3AB1R2J+ AB R 1.2 1W Metal Film

[3] MAIN UNIT

4

14T1-L

RANK MARK DELIVERY
R612 VRD-RM2HD270JY AA R 27 1/2W CarbonR614 VRS-CY1JF154JY AA R 150K 1/16W Metal OxideR615 VRS-CY1JF102JY AA R 1K 1/16W Metal OxideR616 VRS-CY1JF102JY AA R 1K 1/16W Metal OxideR617 VRS-CY1JF123JY AA R 12K 1/16W Metal OxideR618 VRS-CY1JF222JY AA R 2.2K 1/16W Metal OxideR621 VRN-RG2HC150J+ AB R 15 1/2W Metal OxideR622 VRS-RG3DB682J+ AB R 6.8K 2W Metal FilmR625 VRD-RM2HD184JY AA R 180K 1/2W CarbonR626 VRS-CY1JF472JY AA R 4.7K 1/16W Metal OxideR627 VRD-RA2BE222JY AA R 2.2K 1/8W CarbonR631 VRS-RG3LB391J+ AC R 390 3W Metal FilmR637 VRD-RA2BE103JY AA R 10K 1/8W CarbonR638 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR639 VRD-RM2HD471JY AA R 470 1/2W CarbonR702 VRS-RG3AB124J+ AB R 120K 2W Metal OxideR704 VRD-RA2BE221JY AA R 220 1/8W CarbonR705 VRN-RL3DBR82J+ AA R 82 2W Metal FilmR706 VRN-RL3DBR22J+ AB R 22 2W Metal FilmR710 VRD-RM2HD5R6JY AA R 5.6 1/2W CarbonR720 VRD-RA2EE472JY AA R 4.7K 1/4W CarbonR721 VRD-RA2BE683JY AA R 68K 1/8W CarbonR726 VRN-RL2HCR47J+ AB R 47 1/2W Metal OxideR727 VRD-RA2EE102JY AA R 1K 1/4W CarbonR733 VRD-RA2BE273JY AA R 27K 1/8W CarbonR751 VRD-RA2BE273JY AA R 27K 1/8W CarbonR752 RR-DZ0049CEZZY R 39M 1/2W Carbon FilmR753 VRD-RM2HD124JY AA R 12K 1/2W CarbonR754 VRS-RG3AB151J+ AB R 150 2W Metal OxideR755 VRN-RL3AB3R9J+ AB R 3.9 1W Metal FilmR758 VRD-RA2BE471JY AA R 470 1/8W CarbonR761 VRD-RA2EE821JY AA R 820 1/4W CarbonR763 VRN-RL3AB8R2J+ AB R 8.2 1W Metal FilmR764 VRD-RM2HD100JY AA R 10 1/2W CarbonR765 VRD-RM2HD100JY AA R 10 1/2W CarbonR766 VRD-RM2HD100JY AA R 10 1/2W CarbonR803 VRD-RA2BE101JY AA R 100 1/8W CarbonR804 VRD-RA2BE101JY AA R 100 1/8W CarbonR805 VRD-RA2BE101JY AA R 100 1/8W CarbonR806 VRD-RA2BE101JY AA R 100 1/8W CarbonR807 VRS-CY1JF222JY AA R 2.2K 1/16W Metal OxideR808 VRD-RA2BE471JY AA R 470 1/8W CarbonR810 VRS-CY1JF100JY AA R 10 1/16W Metal OxideR811 VRD-RA2BE391JY AA R 390 1/8W CarbonR812 VRD-RA2BE223JY AA R 22K 1/8W CarbonR813 VRD-RA2BE470JY AA R 47 1/8W CarbonR814 VRS-CY1JF391JY AA R 390 1/16W Metal OxideR815 VRS-CY1JF103JY AA R 15K 1/16W Metal OxideR816 VRD-RA2BE101JY AA R 100 1/8W CarbonR817 VRD-RA2BE101JY AA R 100 1/8W CarbonR818 VRD-RA2BE101JY AA R 100 1/8W CarbonR819 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR820 VRD-RA2BE470JY AA R 47 1/8W CarbonR821 VRS-CY1JF102JY AA R 1K 1/16W Metal OxideR822 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR824 VRS-CY1JF103JY AA R 15K 1/16W Metal OxideR825 VRS-CY1JF333JY AA R 33K 1/16W Metal OxideR827 VRD-RM2HD151JY AA R 150 1/2W CarbonR828 VRS-CY1JF391JY AA R 390 1/16W Metal OxideR829 VRD-RA2BE393GY AA R 39K 1/8W CarbonR830 VRD-RA2BE101JY AA R 100 1/8W CarbonR831 VRD-RA2BE101JY AA R 100 1/8W CarbonR833 VRS-CY1JF123JY AA R 12K 1/16W Metal OxideR834 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR837 VRD-RA2BE332JY AA R 3.3K 1/8W CarbonR839 VRS-CY1JF104JY AA R 100K 1/16W Metal OxideR845 VRD-RA2BE103JY AA R 10K 1/8W CarbonR848 VRD-RA2BE181JY AA R 180 1/8W CarbonR862 VRD-RA2BE101JY AA R 100 1/8W Carbon

R1004 VRD-RA2BE101JY AA R 100 1/8W CarbonR1005 VRD-RA2BE101JY AA R 100 1/8W CarbonR1006 VRS-CY1JF332JY AA R 3.3K 1/16W Metal OxideR1007 VRD-RA2BE101JY AA R 100 1/8W CarbonR1008 VRD-RA2BE101JY AA R 100 1/8W CarbonR1010 VRD-RA2BE101JY AA R 100 1/8W CarbonR1011 VRD-RA2BE101JY AA R 100 1/8W CarbonR1012 VRD-RA2BE101JY AA R 100 1/8W CarbonR1013 VRD-RA2BE101JY AA R 100 1/8W CarbonR1014 VRD-RA2BE101JY AA R 100 1/8W CarbonR1015 VRS-CY1JF332JY AA R 3.3K 1/16W Metal OxideR1016 VRS-CY1JF332JY AA R 3.3K 1/16W Metal OxideR1017 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR1019 VRD-RA2BE101JY AA R 100 1/8W CarbonR1020 VRS-CY1JF152JY AA R 1.5K 1/16W Metal OxideR1021 VRS-CY1JF561JY AA R 560 1/16W Metal Oxide

[3] MAIN UNIT

5

14T1-L

R1022 VRS-CY1JF181JY AA R 180 1/16W Metal OxideR1023 VRS-CY1JF222JY AA R 2.2K 1/16W Metal OxideR1024 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR1025 VRS-CY1JF152JY AA R 1.5K 1/16W Metal OxideR1026 VRS-CY1JF681JY AA R 680 1/16W Metal OxideR1027 VRS-CY1JF104JY AA R 100K 1/16W Metal OxideR1028 VRD-RA2BE181JY AA R 180 1/8W CarbonR1029 VRD-RA2BE103JY AA R 10K 1/8W CarbonR1031 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR1032 VRD-RA2BE680JY AA R 68 1/8W CarbonR1035 VRD-RA2BE103JY AA R 10K 1/8W CarbonR1036 VRS-CY1JF122JY AA R 1.2K 1/16W Metal OxideR1037 VRS-CY1JF103JY AA R 10K 1/16W Metal OxideR1038 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR1039 VRS-CY1JF101JY AA R 100 1/16W Metal OxideR1078 VRS-CY1JF332JY AA R 3.3K 1/16W Metal OxideR1079 VRS-CY1JF332JY AA R 3.3K 1/16W Metal Oxide

S701 QSW-P0612CEZZ AG R Switch , POWERS1001 QSW-KA019WJZZ+ AC R Switch , CH UPS1002 QSW-KA019WJZZ+ AC R Switch , CH DOWNS1003 QSW-KA019WJZZ+ AC R Switch , VOL UPS1004 QSW-KA019WJZZ+ AC R Switch , VOL DOWN

F701 QFS-C3225CEZZ AC R Fuse , 3.15A 250V! FH701 QFSHD1013CEZZ+ AC R Fuse Holder

FH702 QFSHD1014CEZZ+ AC R Fuse HolderJ402 QJAKEA056WJ04 R JackJ403 QJAKEA056WJ09 R JackJ405 QJAKH0044AJZZ R Jack

J1404 QJAKE0210CE02 R JackP301 QPLGNA107WJZZ R PlugP601 QPLGN0660CEZZ AC R Plug ,6Pin(F)P602 LHLDW1104PEZZ AB R PlugP701 QPLGN0260CEZZ AC R Plug ,2Pin(M)P702 QPLGN0269GEZZ AB R Plug ,2Pin

P1001 LHLDW1105PEZZ AB R PlugP1003 QPLGNA110WJZZ R PlugPR702 RMPTP0028CEZZ R

RMC1001 RRMCUA050WJZZ R Remote ReceiverRDA301 PRDARA420WJFW R Heat Sink for IC301RDA501 PRDARA121WJFW AD R Heat Sink for IC501RDA602 PRDAR0337PEFW R Heat Sink for Q602RDA701 PRDARA119WJFW AF R Heat Sink for IC701

[4] CRT UNITQ853 RH-TX0110BMZZ+ AC R TX0110Q854 RH-TX0110BMZZ+ AC R TX0110Q855 RH-TX0110BMZZ+ AC R TX0110Q894 VS2SA1530AR-1Y AB R 2SA1530ARD859 VHDHSS4148+-1Y AA R DiodeD896 VHEZJ5R6C++1EY AA R Zener Diode , 5.6VD898 VHDHSS4148+-1Y AA R DiodeL851 VP-MK820K0000+ AB R Peaking 82mHC851 VCKYPA1HB681K+ AA R 680p 50V CeramicC852 VCKYPA1HB681K+ AA R 680p 50V CeramicC853 VCKYPA1HB471K+ AA R 470p 50V CeramicC880 RC-KZ0016CEZZ AC R 10000p 1.5KV CeramicC893 VCEA0A1CW336M+ AB R 33 16V ElectrolyticR849 VRS-CY1JF271JY AA R 270 1/16W Metal OxideR850 VRS-CY1JF470JY AA R 47 1/16W Metal OxideR854 VRS-CY1JF271JY AA R 270 1/16W Metal OxideR855 VRS-CY1JF271JY AA R 270 1/16W Metal OxideR856 VRS-CY1JF470JY AA R 47 1/16W Metal OxideR857 VRS-CY1JF470JY AA R 47 1/16W Metal Oxide

! R859 VRS-VV3DB183J AA R 18K 12W Metal Oxide! R861 VRS-VV3DB183J AA R 18K 12W Metal Oxide! R863 VRS-VV3DB183J AA R 18K 12W Metal Oxide

R864 VRD-RA2BE470JY AA R 47 1/8W CarbonR876 VRS-CY1JF121JY AA R 120 1/16W Metal OxideR877 VRS-CY1JF121JY AA R 120 1/16W Metal OxideR878 VRS-CY1JF121JY AA R 120 1/16W Metal OxideR880 VRD-RM2HD332JY AA R 3.3K 1/2W CarbonR881 VRD-RM2HD332JY AA R 3.3K 1/2W CarbonR882 VRD-RM2HD332JY AA R 3.3K 1/2W CarbonR891 VRS-CY1JF821JY AA R 820 1/16W Metal OxideR892 VRS-CY1JF391JY AA R 390 1/16W Metal OxideR894 VRS-CY1JF152JY AA R 1.5K 1/16W Metal OxideR895 VRD-RA2BE561JY AA R 560 1/8W CarbonP860 LHLDW1104PEZZ AB R Plug 4Pin (H)P880 LHLDW1105PEZZ AB R Plug 5Pin (K)

SC882 QSOCVA022WJZZ AE R Socket , 12PinACC701

! SP301 QACCZA079WJPZ R AC CordVSP9050PA02WA AH R SPEAKER 16 OHMQCNW-2206PEZZ R SP WIRE (+--+)

[3] MAIN UNIT

6

14T1-L

RANK MARK DELIVERY
QCNW-A343WJZZ R H-WIREQCNW-A721WJZZ R K-WIRE

[5] SUPPLIED ACCESSORIESRRMCGA257WJSB R Infrared Remote Control UnitTINS-D308WJZZ R Operation ManualUBATUA004WJZZ R Battery

[4] CRT UNIT

7

14T1-L

[6] CABINET PARTS

NO. PARTS CODE PRICE RANK

NEW MARK

PART DELIVERY DESCRIPTION

[6] CABINET PARTS1 CCABAB906WEV0 - R Front Cabinet Ass'y

1-1 Not Available - - Front Cabinet1-2 JBTN-A689WJSA - R Power Button1-3 MSPRCA067WJFW - R Power Button Spring1-4 GCOVAC351WJSA - R R/C & LED Cover1-5 JBTN-A678WJSA - R Control Button

2 CCABBA134WEV1 - R Rear Cabinet Ass'y2-1 Not Available - - Rear Cabinet

1-51-31-2 1-4

1-1 1

2 2-1

8

14T1-L

[7] PACKING PARTS

NO. PARTS CODE PRICE RANK

NEW MARK

PART DELIVERY DESCRIPTION

[7] PACKING PARTS3 SPAKCD667WJZZ - - Packing Case4 SPAKP0056PEZZ - - Miramat Sheet5 SPAKXB557WJZZ - - Buffer Material6 SSAKA0001PEZZ - - Polyethylene Bag

* Miramat Sheet

6

SPAKP0056PEZZ

SSAKA0001PEZZ

SPAKXB557WJZZ

SPAKCD667WJZZ

*Buffer Material

FIX THE PACKING CASEUSE 2 PACKING TAPES

5

4

*Polyethylene Bag

PACKING OF THE SHEET

Batteries

3

MARK *: Not replacement items

* Packing Case

Infra Red R/C Unit

Operation Manual

9

14T1-L

INDEXPARTS CODE No. PRICE

RANKNEW

MARKPART RANK

[ C ]

CCABAB906WEV0 6-1 - RCCABBA134WEV1 6-2 - R

[ D ]

DUNTKE161WEA1 2- - -DUNTKE162WEA1 2- - -

[ G ]

GCOVAC351WJSA 6-1-4 - R[ J ]

JBTN-A678WJSA 6-1-5 - RJBTN-A689WJSA 6-1-2 - R

[ L ]

LHLDW1104PEZZ 3-P602 AB R" 4-P860 AB R

LHLDW1105PEZZ 3-P1001 AB R" 4-P880 AB R

[ M ]

MSPRCA067WJFW 6-1-3 - R[ N ]

Not Available 6-1-1 - -" 6-2-1 - -

[ P ]

PMAGF3045CEZZ 1- RPRDAR0337PEFW 3-RDA602 RPRDARA119WJFW 3-RDA701 AF RPRDARA121WJFW 3-RDA501 AD RPRDARA420WJFW 3-RDA301 R

[ Q ]

QACCZA079WJPZ 4-SP301 RQCNW-2206PEZZ 4- RQCNW-A343WJZZ 4- RQCNW-A721WJZZ 4- RQEARC1422PEZZ 1- RQFS-C3225CEZZ 3-F701 AC RQFSHD1013CEZZ+ 3-FH701 AC RQFSHD1014CEZZ+ 3-FH702 AC RQJAKE0210CE02 3-J1404 RQJAKEA056WJ04 3-J402 RQJAKEA056WJ09 3-J403 RQJAKH0044AJZZ 3-J405 RQJUM-0001AJFWY 3-R508 R

" 3-R509 RQPLGN0260CEZZ 3-P701 AC RQPLGN0269GEZZ 3-P702 AB RQPLGN0660CEZZ 3-P601 AC RQPLGNA107WJZZ 3-P301 RQPLGNA110WJZZ 3-P1003 RQSOCVA022WJZZ 4-SC882 AE RQSW-KA019WJZZ+ 3-S1001 AC R

" 3-S1002 AC R" 3-S1003 AC R" 3-S1004 AC R

QSW-P0612CEZZ 3-S701 AG R[ R ]

RC-EZA095WJZZ 3-C705 AM RRC-EZA235WJZZ 3-C753 AD RRC-EZA522WJZZ 3-C754 AD RRC-FZ032SCEZZ 3-C701 AD RRCILFA187WJZZ 3-L701 AD RRCILGA114WJZZ 1- RRC-KZ0016CEZZ 4-C880 AC RRC-KZ0029CEZZ+ 3-C702 AC R

" 3-C703 AC R" 3-C704 AC R

RC-KZ0102GEZZ 3-C713 AC RRCRSAA058WJZZ 3-X801 RRFILCA055WJQZS 3-SF201 RRH-DX0066GEZZY 3-D706 AC R

" 3-D707 AC R" 3-D709 AC R" 3-D721 AC R

RH-DX0131CEZZY 3-D510 AC R" 3-D511 AC R" 3-D606 AC R" 3-D720 AC R

RH-DX0247CEZZ 3-D752 AE RRH-DX0302CEZZ 3-D393 AE RRH-DX0441CEZZY 3-D505 AC RRH-DX0476CEZZ 3-D701 AG RRH-DXA044WJZZ 3-D751 R

10

14T1-L

RH-EX0277TAZZY 3-D801 AA R" 3-D802 AA R" 3-D803 AA R

RH-EX0612GEZZY 3-D503 AB RRH-EX1393CEZZY 3-D806 AB R

" 3-D1003 AB R" 3-D1004 AB R

RH-IXC227WJZZQ 3-IC801 RRH-PX0013PEZZ 3-D1001 AC RRH-TX0110BMZZ+ 4-Q853 AC R

" 4-Q854 AC R" 4-Q855 AC R

RH-VXA182WJZZ 3-VA701 RRMPTP0028CEZZ 3-PR702 RRR-DZ0049CEZZY 3-R752 RRRMCGA257WJSB 5- RRRMCUA050WJZZ 3-RMC1001 RRTRNFA140WJZZ 3-T602 RRTRNWA287WJZZ 3-T702 RRTRNZA058WJZZ 3-T603 AD RRTUNQA037WJZZ 3-TU201 R

[ S ]

SPAKCD667WJZZ 7-3 - -SPAKP0056PEZZ 7-4 - -SPAKXB557WJZZ 7-5 - -SSAKA0001PEZZ 7-6 - -

[ T ]

TINS-D308WJZZ 5- R[ U ]

UBATUA004WJZZ 5- R[ V ]

VB370BVBK1S9E 1- RVCCCCY1HH101JY 3-C1005 AA RVCE9GA1HW225M+ 3-C372 AB R

" 3-C395 AB RVCEA0A1AW107M+ 3-C758 AB R

" 3-C846 AB R" 3-C1001 AB R

VCEA0A1AW108M+ 3-C202 AC R" 3-C307 AC R

VCEA0A1CW106M+ 3-C370 AB R" 3-C383 AB R" 3-C810 AB R" 3-C827 AB R" 3-C829 AB R" 3-C831 AB R" 3-C833 AB R" 3-C847 AB R" 3-C1003 AB R

VCEA0A1CW336M+ 3-C306 AB R" 4-C893 AB R

VCEA0A1CW476M+ 3-C722 AC R" 3-C816 AB R" 3-C818 AB R

VCEA0A1CW477M+ 3-C451 AC R" 3-C516 AC R" 3-C721 AC R

VCEA0A1EW108M+ 3-C393 AD RVCEA0A1EW228M+ 3-C756 AE RVCEA0A1EW476M+ 3-C301 AB RVCEA0A1EW477M+ 3-C308 AD RVCEA0A1HW104M+ 3-C1853 AB RVCEA0A1HW105M+ 3-C304 AB RVCEA0A1HW106M+ 3-C206 AB R

" 3-C1859 AB RVCEA0A1HW107M+ 3-C505 AB RVCEA0A1HW475M+ 3-C211 AB R

" 3-C314 AB R" 3-C602 AB R" 3-C808 AB R" 3-C825 AB R" 3-C843 AB R

VCEA0A1HW476M+ 3-C719 AB RVCEA0A1VW477M+ 3-C511 AB RVCEA0A2EW336M+ 3-C604 AD RVCFPVC2EB334J 3-C611 AD RVCFPVC3ZA612H 3-C607 AD RVCFYAA2AA224J+ 3-C508 AD RVCFYFA1HA103J+ 3-C844 AA RVCFYFA1HA105J+ 3-C706 AE RVCFYFA1HA154J+ 3-C835 AA RVCFYFA1HA224J+ 3-C840 AA R

PARTS CODE No. PRICE RANK

NEW MARK

PART RANK

11

14T1-L


NEW MARK

PART RANK

VCFYFA1HM104J+ 3-C1081 AA RVCKYCY1AB105KY 3-C820 AA R

" 3-C822 AA R" 3-C842 AA R

VCKYCY1CF224ZY 3-C845 AB RVCKYCY1CF474ZY 3-C1004 AB RVCKYCY1EF104ZY 3-C1016 AA RVCKYCY1HB102KY 3-C836 AA R

" 3-C837 AA RVCKYCY1HB103KY 3-C817 AA R

" 3-C832 AA RVCKYCY1HB103ZY 3-C207 AA R

" 3-C208 AA R" 3-C209 AA R" 3-C210 AA R

VCKYCY1HB104KY 3-C759 AA R" 3-C809 AA R" 3-C812 AA R" 3-C815 AA R" 3-C826 AA R" 3-C828 AA R" 3-C830 AA R" 3-C848 AA R

VCKYCY1HB153KY 3-C305 AA RVCKYCY1HB223KY 3-C839 AA RVCKYCY1HF103ZY 3-C203 AA RVCKYCY1HF224ZY 3-C1852 AA RVCKYPA1HB102K+ 3-C391 AA RVCKYPA1HB221K+ 3-C708 AB RVCKYPA1HB222K+ 3-C711 AB RVCKYPA1HB471K+ 4-C853 AA RVCKYPA1HB681K+ 4-C851 AA R

" 4-C852 AA RVCKYPA2HB101K+ 3-C650 AB RVCKYPA2HB102K+ 3-C512 AA R

" 3-C515 AA R" 3-C606 AA R" 3-C720 AA R" 3-C750 AA R

VCKYPH3DB561K 3-C752 AC R" 3-C784 AC R

VCQYTA1HM103J+ 3-C709 AB RVCQYTA1HM222J+ 3-C710 AB RVCQYTA1HM472J+ 3-C608 AB RVCQYTA1HM563J+ 3-C601 AB RVCQYTA1HM682J+ 3-C841 AB RVHD1SS244//-1Y 3-D602 AB RVHDHSS4148+-1Y 3-D203 AA R

" 3-D204 AA R" 3-D302 AA R" 3-D303 AA R" 3-D605 AA R" 3-D607 AA R" 3-D710 AA R" 3-D725 AA R" 3-D759 AA R" 3-D764 AA R" 3-D804 AA R" 3-D805 AA R" 3-D1005 AA R" 3-D1007 AA R" 3-D1008 AA R" 4-D859 AA R" 4-D898 AA R

VHEZJ12B+++1EY 3-D301 AA R" 3-D723 AA R" 3-D808 AC R

VHEZJ27B+++1EY 3-D603 AA RVHEZJ27D+++1EY 3-D722 AA RVHEZJ33C+++1EY 3-D201 AA RVHEZJ36C+++1EY 3-D736 AB RVHEZJ3R3A++1EY 3-D758 RVHEZJ4R3B++1EY 3-D724 RVHEZJ5R1A++1EY 3-D754 RVHEZJ5R1B++1EY 3-D807 AC RVHEZJ5R6B++1EY 3-D608 AA R

" 3-D715 AA RVHEZJ5R6C++1EY 4-D896 AA RVHEZJ8R2A++1EY 3-D732 AB RVHEZJ8R2B++1EY 3-D760 AB R


NEW MARK

PART RANK

VHIBR24L08F-1Y 3-IC1003 AE RVHILA42031E-1 3-IC301 RVHISTRW5453-1 3-IC701 AM RVHISTV9302B-1 3-IC501 RVP-DF100K0000Y 3-L804 AB R

" 3-L805 AB R" 3-L807 AB R

VP-DF270K0000Y 3-L203 AB RVP-MK820K0000+ 4-L851 AB RVP-XF100K0000Y 3-L808 AB R

" 3-L809 AB R" 3-L810 AB R

VP-XF1R2K0000Y 3-L204 AB RVP-XF2R7K0000Y 3-L205 AB RVP-XF4R7K0000Y 3-L802 AB R

" 3-L812 AB R" 3-L813 AB R

VRD-RA2BE101JY 3-R201 AA R" 3-R202 AA R" 3-R323 AA R" 3-R803 AA R" 3-R804 AA R" 3-R805 AA R" 3-R806 AA R" 3-R816 AA R" 3-R817 AA R" 3-R818 AA R" 3-R830 AA R" 3-R831 AA R" 3-R862 AA R" 3-R1004 AA R" 3-R1005 AA R" 3-R1007 AA R" 3-R1008 AA R" 3-R1010 AA R" 3-R1011 AA R" 3-R1012 AA R" 3-R1013 AA R" 3-R1014 AA R" 3-R1019 AA R

VRD-RA2BE103JY 3-R637 AA R" 3-R845 AA R" 3-R1029 AA R" 3-R1035 AA R

VRD-RA2BE151JY 3-R431 AA RVRD-RA2BE181JY 3-R848 AA R

" 3-R1028 AA RVRD-RA2BE221JY 3-R704 AA RVRD-RA2BE222JY 3-R627 AA RVRD-RA2BE223JY 3-R304 AA R

" 3-R812 AA RVRD-RA2BE273JY 3-R603 AA R

" 3-R733 AA R" 3-R751 AA R

VRD-RA2BE332JY 3-R837 AA RVRD-RA2BE391JY 3-R811 AA RVRD-RA2BE393GY 3-R829 AA RVRD-RA2BE393JY 3-R602 AA RVRD-RA2BE470JY 3-R813 AA R

" 3-R820 AA R" 4-R864 AA R

VRD-RA2BE471JY 3-R758 AA R" 3-R808 AA R

VRD-RA2BE561JY 4-R895 AA RVRD-RA2BE563JY 3-R604 AA RVRD-RA2BE680JY 3-R1032 AA RVRD-RA2BE683JY 3-R721 AA RVRD-RA2BE822JY 3-R301 AA RVRD-RA2EE102JY 3-R727 AA RVRD-RA2EE472JY 3-R720 AA RVRD-RA2EE750JY 3-R459 AA RVRD-RA2EE821JY 3-R761 AA RVRD-RM2HD100JY 3-R764 AA R

" 3-R765 AA R" 3-R766 AA R

VRD-RM2HD124JY 3-R753 AA RVRD-RM2HD151JY 3-R827 AA RVRD-RM2HD154JY 3-R605 AA RVRD-RM2HD184JY 3-R625 AA RVRD-RM2HD1R0JY 3-R325 AA R


NEW MARK

PART RANK

12

14T1-L

" 3-R507 AA RVRD-RM2HD270JY 3-R609 AA R

" 3-R612 AA RVRD-RM2HD332JY 4-R880 AA R

" 4-R881 AA R" 4-R882 AA R

VRD-RM2HD471JY 3-R639 AA RVRD-RM2HD5R6JY 3-R710 AA RVRN-RG2HC150J+ 3-R621 AB RVRN-RL2HCR47J+ 3-R726 AB RVRN-RL3AB1R2J+ 3-R611 AB RVRN-RL3AB3R9J+ 3-R755 AB RVRN-RL3AB8R2J+ 3-R763 AB RVRN-RL3ABR10J+ 3-R391 AA RVRN-RL3DB2R7J+ 3-R503 AB RVRN-RL3DBR22J+ 3-R706 AB RVRN-RL3DBR82J+ 3-R705 AA RVRN-RL3LBR18J+ 3-R606 AD RVRN-RL3LBR22J+ 3-R608 AD RVRS-CY1JF000JY 3-RJ14 AA R

" 3-RJ17 AA R" 3-RJ22 AA R" 3-RJ23 AA R

VRS-CY1JF100JY 3-R810 AA RVRS-CY1JF101JY 3-R638 AA R

" 3-R819 AA R" 3-R822 AA R" 3-R834 AA R" 3-R1017 AA R" 3-R1024 AA R" 3-R1031 AA R" 3-R1038 AA R" 3-R1039 AA R

VRS-CY1JF102JY 3-R324 AA R" 3-R615 AA R" 3-R616 AA R" 3-R821 AA R

VRS-CY1JF103JY 3-R213 AA R" 3-R365 AA R" 3-R372 AA R" 3-R383 AA R" 3-R458 AA R" 3-R815 AA R" 3-R824 AA R" 3-R1037 AA R

VRS-CY1JF104JY 3-R322 AA R" 3-R839 AA R" 3-R1027 AA R


VRS-CY1JF122JY 3-R315 AA R" 3-R1036 AA R



" 3-R1025 AA R" 4-R894 AA R

VRS-CY1JF154JY 3-R614 AA RVRS-CY1JF181JY 3-R1022 AA RVRS-CY1JF183JY 3-R515 AA RVRS-CY1JF221JY 3-R207 AA R

" 3-R208 AA R" 3-R220 AA R" 3-R432 AA R

VRS-CY1JF222JY 3-R513 AA R" 3-R618 AA R" 3-R807 AA R" 3-R1023 AA R




" 3-R1015 AA R" 3-R1016 AA R" 3-R1078 AA R" 3-R1079 AA R

VRS-CY1JF333JY 3-R825 AA R


NEW MARK

PART RANK



" 4-R856 AA R" 4-R857 AA R

VRS-CY1JF472JY 3-R626 AA RVRS-CY1JF473JY 3-R303 AA RVRS-CY1JF561JY 3-R314 AA R

" 3-R1021 AA RVRS-CY1JF563JY 3-R214 AA RVRS-CY1JF680JY 3-R205 AA RVRS-CY1JF681JY 3-R1026 AA RVRS-CY1JF682JY 3-R366 AA R

" 3-R384 AA RVRS-CY1JF750JY 3-R461 AA RVRS-CY1JF821JY 4-R891 AA RVRS-RG3AB124J+ 3-R702 AB RVRS-RG3AB151J+ 3-R754 AB RVRS-RG3AB331J+ 3-R506 AB RVRS-RG3DB682J+ 3-R622 AB RVRS-RG3LB391J+ 3-R631 AC RVRS-RG3LB393J+ 3-R216 AC RVRS-VV3AB101J 3-R607 AA RVRS-VV3AB121J 3-R601 AA RVRS-VV3DB183J 4-R859 AA R

" 4-R861 AA R" 4-R863 AA R

VS2SA1530AR-1Y 3-Q302 AB R" 4-Q894 AB R

VS2SC2235Y/1E+ 3-Q601 AE RVS2SC2735//1EY 3-Q201 RVS2SC3198-G/-1+ 3-Q754 AD R

" 3-Q755 AD RVS2SC3198-G-1+ 3-Q603 AA RVS2SC3928AR-1Y 3-Q801 AB R

" 3-Q803 AB R" 3-Q1070 AB R

VS2SD468-C/-1+ 3-Q751 AD RVSP9050PA02WA 4- AH RVSTT2140+++-F 3-Q602 AG R


NEW MARK

PART RANK

13

14T1-L

14

– 1

No part of this publication may be reproduced,stored in a retrieval system, or transmitted inany form or by any means, electronic, mechanical,photocopying, recording, or otherwise, withoutprior written permission of the publisher.

COPYRIGHT © XXXX BYSHARP CORPORATION

ALL RIGHTS RESERVED.

EndPage

No part of this publication may be reproduced,stored in a retrieval system, or transmitted inany form or by any means, electronic, mechanical,photocopying, recording, or otherwise, withoutprior written permission of the publisher.

COPYRIGHT © XXXX BYSHARP CORPORATION

ALL RIGHTS RESERVED.

COPYRIGHT 2007 BY SHARP CORPORATION

SHARP-ROXY ELECTRONICSCORPORATION (M) SDN. BHDQRC DEPARTMENTBatu Pahat, Johor, MalaysiaP.O.BOX 513

RQ0081-SAugust 2007 Printed in Malaysia

Design and Production InformationDesign :SEMProduction :SREC

CHS.FLE

14T1L

Documents

Transcript of 14T1L