Insert two Nuts M5 into the LNBF Mounting Rail.

Place the LNBF mounting Rail Holder on the middle of the LNBF Mounting Rail. Insert one Spring Washer M5 & one Washer M5 into the Bolt M5x12 and screw the Bolt into the Nuts M5. Repeat the last step with the second Bolt M5x12.

Insert one Nut M5 into the LNBF Mounting rail and place one LNBF clamps. Insert one Washer M5 into the bolt M5x12 and screw the bolt into the Nut M5.

Repeat the previous step for the 3 remaining LNBF Clamps. Make sure to insert two LNBF Clamps from the left side of the LNBF Mounting Rail and two LNBF clamps from the right side.

Place the LNBF Arm into the LNBF mounting Rail Holder. Insert the Carriage Bolt M6x25 and screw it into the Nut M6.

Place the Rotation Bracket Side on the Rotation Bracket and screw two Carriage Bolts M6x12 using two Nuts M6.

Place and screw the Rotation Bracket on the Reflector Back Mount using three Hexagonal Flange Bolts M6x12.

SRT D60M - INSTRUCTION

Place and screw the Elevation Bracket on the Rotation Bracket with four Carriage Bolts M6x12 & four Nuts M6. Warning: Make sure to use the hole A.

Place the two M6 U-shaped bolts inside the Elevation Bracket and fix the two Pole Clamps using four Nuts M6.

Screw the LNBF arm on the Reflector Back Mount using two Carriage Bolts M6x12 and two Nuts M6.

Place and screw the Reflector on the Reflector Back Mount using four Carriage Bolts M8x16 and four Nuts M8

1.2

Step 1 : REFLECTOR MOUNTING

1.1 1.3 1.4

1.5 1.6 1.7 1.8

1.9 1.10 1.11

www.stronghd.tv - For more information, please visit www.strong-technologies.com/SRTD60M

Find a location where to install your dish facing the South. Make sure to select an outdoor site with a clear, unobstructed view of the South, Southeast, or Southwest.

Place the Stand Based U-shaped Clamp (perpendicu-lar to the ground) on the wall Drill two holes.

Screw two Anchor Bolts M6x50.

Place and screw the Stand Pole using one Bolt M6x45 and one Nut M6.

Place and screw the two Stand Side Legs to the Stand Pole using one Bolt M6x45 and one Nut M6.

Make sure the Stand Pole is perfectly perpendicular to the ground and parralel to the wall and drill two holes.

Place and screw two Anchor Bolts M6x50.

Place the reflector on the Stand Pole and screw the four Nuts M6 of the two M6 U-Shaped Bolts.

Place four LNBFs into the LNBF clamps.

SRT D60M - INSTRUCTION

2.1

Step 2 : STAND MOUNTING

2.3 2.4

2.5 2.6 2.7

2.2

2.8

www.stronghd.tv - For more information, please visit www.strong-technologies.com/SRTD60M

Place the Stand Based U-shaped Clamp on the ground facing North/South direction. Drill two holes and screw two Anchor Bolts M6x50.

Place and screw the Stand Pole using one Bolt M6x45 and one Nut M6.Place and screw the two Stand Side Legs to the Stand Pole using one Bolt M6x45 and one Nut M6.

Make sure the Stand Pole is perfectly perpendicular to the ground and drill two holes.Place and screw two Anchor Bolts M6x50.

Place the reflector on the Stand Pole and screw the four Nuts M6 of the two M6 U-Sha-ped Bolts.

2.1 2.3 2.4 2.62.2NORTH

SOUTH

NORTH

SOUTH

SOUTH

NORTH

Place four LNBFs into the LNBF clamps.

TERRACE MOUNTING

WALL MOUNTING

SRT D60M - INSTRUCTION

Plug the RG-6 cable in the third LNBF pointing to Eutelsat 16A (Focal Point LNBF)

SRT D60M - INSTRUCTIONStep 3 : SATELLITES TRACKING

3.1 Eutelsat 16A at 16° East

Go to Menu, Installation, Enter 0000Go to Dish Setting & Select-Satellite:16.0E Eutelsat 16A-Frequency: 12.522 GHz-Symbol Rate: 30.000 MS/s-Polarization: H

Slightly rotate the reflector as shown on the above picture.You have to find the good elevation (up & down) and azimuth (right & left) then tight the screws of the Pole Clamps, Elevation and Rotation Brackets.Adjust the LNBF polarization in order to get the best signal reception, then tight the screw of the LNBF holder.

Plug the RG-6 cable on the fourth LNBF pointing to SES 5 and Eutelsat 7A

3.3 SES 5 & Eutelsat 7A at 5° and 7° East

Go to Menu, Installation, Enter 0000Go to Dish Setting & Select-Satellite:7.0 EUTELSAT 7A-Frequency: 10.928 GHz-Symbol Rate: 30.000 MS/s-Polarization: H

Track the signal by adjusting the LNBF Clamp on the LNBF Mounting Rail. If you cannot receive the signal, rotate the reflector until you receive the signal. If you have to rotate the reflector, make sure you still have the signal on Eutelsat 36A.

Plug the RG-6 cable in the first LNBF pointing to Eutelsat 36A

Plug the RG-6 cable on the second LNBF pointing to Astra 2F

3.2

3.4

Eutelsat 36A at 36°East

Astra 2F at 28.2° East

Go to Menu, Installation, Enter 0000Go to Dish Setting & Select-Satellite: 36.0E Eutelsat 36A/36-Frequency: 12.245 GHz-Symbol Rate: 27.500 MS/s-Polarization: H

Go to Menu, Installation, Enter 0000Go to Dish Setting & Select-Satellite: 28,2E ASTRA 1N/2A/2F-Frequency: 12.525 GHz-Symbol Rate: 27.000 MS/s-Polarization: H

Track the signal by adjusting the LNBF Clamp on the LNBF Mounting Rail and Rotating the reflector. Once you have the signal on Eutelsat 36A, make sure you still have the signal on Eutelsat 16A

Track the signal by only adjusting the LNBF Clamp. Once you received the signal from Astra 2F, make sure you are receiving all the desired satellites.Finetune each LNBF to maximize the signal reception of all satellites.

Go to Menu, Installation, Enter 0000Go to Dish Setting & Select-Satellite: 4.9° ASTRA4A/SES5 -Frequency: 12.054 GHz-Symbol Rate: 29.950 MS/s-Polarization: V

Track SES 5 by finetuning the LNBF on the LNBF Mounting Rail. Make sure you are recei-ving the signal on both SES 5 and Eutelsat 7A

www.stronghd.tv - For more information, please visit www.strong-technologies.com/SRTD60M

■ Optimize received signal strength & quality ■ Increase your Mobility ■ Save Precious Time ■ Go After more Business

www.strong-technologies.com/srt-DSM1

SRT DSM1STRONG SATELLITE METER

Crimp four RG-6 cables of 90 cm long each. Crimp one RG-6 cable (dis-tance between the DiSEqC switch and the receiver).

Connect the four RG-6 cables to the LNBFs.

SRT D60M - INSTRUCTION

4.2

Step 4 : DiSEqC SETTING

4.1 4.4

4.5

4.3

Place two self-locking plastics around the LNBF Arm.Place all the RG6 cables into the self-locking plastics.

Use one DiSEqC switch SRT 4X1 to connect the 4 LNBFs to the receiver. -Input LNB 1: Eutelsat 36A -Input LNB 3: Eutelsat 16A -Input LNB 2: Astra 2F -Input LNB 4: SES 5 & Eutelsat 7AOutput Receiver: Plug the RG-6 cable from the DiSEqC to the receiver

Satellite 36.0E Eutelsat 36A/36

28.2E ASTRA 1N/2A/2F

16.0 EUTELSAT 16A

4.9E ASTRA 4A /SES5

7.0E EUTELSAT 7A

Frequency 12.245 Ghz (H) 12.526 Ghz (H) 12.522 GHz (H) 12.054 GHz (V) 10.928 Ghz (H)DiSEqC 1.0 OFF OFF OFF OFF OFFDiSEqC 1.1 1 of 16 2 of 16 3 of 16 4 of 16 4 of 16

Go to Installation, Enter as password 0000, Go to Dish Setting: Select the below information for each Satellite.

www.stronghd.tv - For more information, please visit www.strong-technologies.com/SRTD60M

TERRACE MOUNTINGWALL MOUNTING