04- OKI 8251 (USART)

1/26

Semiconductor MSM82C51A-2RS/GS/JS

GENERAL DESCRIPTION

The MSM82C51A-2 is a USART (Universal Synchronous Asynchronous Receiver Transmitter)for serial data communication.As a peripheral device of a microcomputer system, the MSM82C51A-2 receives parallel datafrom the CPU and transmits serial data after conversion. This device also receives serial datafrom the outside and transmits parallel data to the CPU after conversion.The MSM82C51A-2 configures a fully static circuit using silicon gate CMOS technology.Therefore, it operates on extremely low power at 100 mA (max) of standby current bysuspending all operations.

FEATURES

Wide power supply voltage range from 3 V to 6 V Wide temperature range from 40C to 85C Synchronous communication upto 64 Kbaud Asynchronous communication upto 38.4 Kbaud Transmitting/receiving operations under double buffered configuration. Error detection (parity, overrun and framing) 28-pin Plastic DIP (DIP28-P-600-2.54): (Product name: MSM82C51A-2RS) 28-pin Plastic QFJ (QFJ28-P-S450-1.27): (Product name: MSM82C51A-2JS) 32-pin Plastic SSOP(SSOP32-P-430-1.00-K): (Product name: MSM82C51A-2GS-K)

SemiconductorMSM82C51A-2RS/GS/JSUNIVERSAL SYNCHRONOUS ASYNCHRONOUS RECEIVER TRANSMITTER

E2O0017-27-X2

This version: Jan. 1998Previous version: Aug. 1996

This product is not available in Asia and Oceania.

2/26


FUNCTIONAL BLOCK DIAGRAM

TXDD7 - D0

RESETCLK C/DRDWRCS

DSRDTRCTSRTS

Read/WriteControlLogic

ModemControl

TransmitBuffer(P - S)

TransmitControl

RecieveBuffer(S - P)

RecieveControl

TXRDYTXETXC

RXD

RXRDYRXCSYNDET/BD

Data BusBuffer

Inte

rnal

Bus

Lin

e

3/26


PIN CONFIGURATION (TOP VIEW)

D1

D0

VCC

RXC

DTR

RTS

DSR

RESET

CLK

TXD

TXEMPTY

CTS

SYNDET/BD

TXRDY

1

2

3

4

5

6

7

8

9

10

11

12

28

27

26

25

24

23

22

21

20

19

18

17

13

14

16

15

28 pin Plastic DIP

D7

D6

D5

GND

RXD

D4

D3

D2

WR

CS

C/D

RD

RXRDY

TXC

32 pin Plastic SSOP

16

15

14

13

NC

D7

D6

D5

GND

RXD

D4

D3

D2 D1

D0

WR

CS

NC

C/D

RD

RXRDY

VCC

RXC

TXC

NC

DTR

RTS

DSR

RESET

CLK

TXD

TXEMPTY

NC

CTS

SYNDET/BD

TXRDY

1

2

3

4

5

6

7

8

9

10

11

12

24

23

22

21

20

19

18

29

30

31

32

28

27

26

25

17

25

24

23

22

21

20

19

RXC

DTR

RTS

DSR

RESET

CLK

TXD

D4

D5

D6

D7

TXC

WR

CS

12 13 14 15 16 17 18

C/D RD

RXR

DY

TXR

DY

SYN

DET

/BD

CTS

TXEM

PTY

4 3 2 1 28 27 26

GN

D

RXD

D3

D2

D1 D0

5

6

7

8

9

10

11

V CC

28 pin Plastic QFJ

4/26


FUNCTION

Outline

The MSM82C51A-2's functional configuration is programed by software.Operation between the MSM82C51A-2 and a CPU is executed by program control. Table 1shows the operation between a CPU and the device.

0

00

Data Bus 3-State

1 Data Bus 3-State

CS

11

C/D

Status fi CPUControl Word CPU

1

10

0 Data CPU

0 Data fi CPU0

0

0

1

WR

1

01

1

0

RD

Table 1 Operation between MSM82C51A and CPU

It is necessary to execute a function-setting sequence after resetting the MSM82C51A-2. Fig. 1shows the function-setting sequence.If the function was set, the device is ready to receive a command, thus enabling the transfer ofdata by setting a necessary command, reading a status and reading/writing data.

Asynchronous

External Reset

Internal Reset

Write Mode Instruction

Write First Sync Charactor

yes

no

SingleSync Mode

Write Second SyncCharactor

yes

no

End of Mode Setting

Fig. 1 Function-setting Sequence (Mode Instruction Sequence)

5/26


Control Words

There are two types of control word.1. Mode instruction (setting of function)2. Command (setting of operation)

1) Mode InstructionMode instruction is used for setting the function of the MSM82C51A-2. Mode instructionwill be in wait for write at either internal reset or external reset. That is, the writing of acontrol word after resetting will be recognized as a mode instruction.Items set by mode instruction are as follows:

Synchronous/asynchronous mode Stop bit length (asynchronous mode) Character length Parity bit Baud rate factor (asynchronous mode) Internal/external synchronization (synchronous mode) Number of synchronous characters (Synchronous mode)

The bit configuration of mode instruction is shown in Figures 2 and 3. In the case ofsynchronous mode, it is necessary to write one-or two byte sync characters.If sync characters were written, a function will be set because the writing of sync charactersconstitutes part of mode instruction.

S1 S1 EP PEN L2 L1 B2 B1

D7 D6 D5 D4 D3 D2 D1 D0

0 1 0 1

0 0 1 1Refer toFig. 3SYNC

1 16 64

Baud Rate Factor

0 1 0

0 0 1

5 bits 6 bits 7 bits

Charactor Length

1

1

8 bits

0 1 0 1

0 0 1 1

DisableOdd

Parity DisableEvenParity

Parity Check

0 1 0

0 0 1

Inhabit 1 bit 1.5 bits

Stop bit Length

1

1

2 bits

Fig. 2 Bit Configuration of Mode Instruction (Asynchronous)

6/26


D7 D6 D5 D4 D3 D2 D1 D0

SCS ESD EP PEN L2 L1 0 0

Charactor Length

0 1 0

0 0 1

5 bits 6 bits 7 bits

1

1

8 bits

0 1 0 1

0 0 1 1

DisableOdd

Parity DisableEvenParity

Parity

0 1

InternalSynchronization

ExternalSynchronization

Synchronous Mode

0 1

2 Charactors 1 Charactor

Number of Synchronous Charactors

Fig. 3 Bit Configuration of Mode Instruction (Synchronous)

7/26


2) Command

Command is used for setting the operation of the MSM82C51A-2.It is possible to write a command whenever necessary after writing a mode instruction andsync characters.Items to be set by command are as follows:

Transmit Enable/Disable Receive Enable/Disable DTR, RTS Output of data. Resetting of error flag. Sending to break characters Internal resetting Hunt mode (synchronous mode)

The bit configuration of a command is shown in Fig. 4.

EH

D7

IR

D6

RTS

D5

ER

D4

SBRK

D3

RXE

D2

DTR

D1

TXEN

D0

1Transmit Enable

0Disable

DTR1 fi DTR = 00 fi DTR = 1

1Recieve Enable

0Disable

1Sent Break Charactor

0Normal Operation

1Reset Error Flag

0Normal Operation

RTS1 fi RTS = 00 fi RTS = 1

1Internal Reset

0Normal Operation

1Hunt Mode (Note)

0Normal Operation

Note: Seach mode for synchronouscharactors in synchronous mode.

Fig. 4 Bit Configuration of Command

8/26


Status Word

It is possible to see the internal status of MSM82C51A-2 by reading a status word.The bit configuration of status word is shown in Fig. 5.

Same as terminal.Refer to "Explanation" of Terminals.

DSR

D7SYNDET

/BD

D6

FE

D5

OE

D4

PE

D3

TXEMPTY

D2

RXRDY

D1

TXRDY

D0

Parity Different from TXRDY Terminal.Refer to "Explanation" of TXRDY Terminals.

1Parity Error

1Overrun Error

1Framing Error

Note:

Shows Terminal DSR1DSR = 00DSR = 1

Only asynchronous mode.Stop bit cannot be detected.

Fig. 5 Bit Configuration of Status Word

Standby Status

It is possible to put the MSM82C51A-2 in standby statusWhen the following conditions have been satisfied the MSM82C51A-2 is in standby status.

(1) CS terminal is fixed at Vcc level.(2) Input pins other CS , D0 to D7, RD, WR and C/D are fixed at Vcc or GND level (including

SYNDET in external synchronous mode).

Note: When all output currents are 0, ICCS specification is applied.

9/26


Pin Description

D0 to D7 (l/O terminal)This is bidirectional data bus which receive control words and transmits data from the CPU andsends status words and received data to CPU.

RESET (Input terminal)A High on this input forces the MSM82C51A-2 into reset status.The device waits for the writing of mode instruction.The min. reset width is six clock inputs during the operating status of CLK.

CLK (Input terminal)CLK signal is used to generate internal device timing.CLK signal is independent of RXC or TXC.However, the frequency of CLK must be greater than 30 times the RXC and TXC at Synchronousmode and Asynchronous x1 mode, and must be greater than 5 times at Asynchronous x16and x64 mode.

WR (Input terminal)This is the active low input terminal which receives a signal for writing transmit data andcontrol words from the CPU into the MSM82C51A-2.

RD (Input terminal)This is the active low input terminal which receives a signal for reading receive data andstatus words from the MSM82C51A-2.

C/D (Input terminal)This is an input terminal which receives a signal for selecting data or command words and statuswords when the MSM82C51A-2 is accessed by the CPU.If C/D = low, data will be accessed.If C/D = high, command word or status word will be accessed.

CS (Input terminal)This is the active low input terminal which selects the MSM82C51A-2 at low level when theCPU accesses.

Note: The device wont be in standby status; only setting CS = High.Refer to Explanation of Standby Status.

TXD (output terminal)This is an output terminal for transmitting data from which serial-converted data is sent out.The device is in mark status (high level) after resetting or during a status when transmit isdisabled. It is also possible to set the device in break status (low level) by a command.

10/26


TXRDY (output terminal)This is an output terminal which indicates that the MSM82C51A-2 is ready to accept atransmitted data character. But the terminal is always at low level if CTS = high or the devicewas set in TX disable status by a command.

Note: TXRDY status word indicates that transmit data character is receivable,regardless

of CTS or command.If the CPU writes a data character, TXRDY will be reset by the leading edge or WR

signal.

TXEMPTY (Output terminal)This is an output terminal which indicates that the MSM82C51A-2 has transmitted all thecharacters and had no data character.In synchronous mode, the terminal is at high level, if transmit data characters are no longerremaining and sync characters are automatically transmitted. If the CPU writes a datacharacter, TXEMPTY will be reset by the leading edge of WR signal.

Note : As the transmitter is disabled by setting CTS High or command, data writtenbefore disable will be sent out. Then TXD and TXEMPTY will be High.Even if a data is written after disable, that data is not sent out and TXE will be

High.After the transmitter is enabled, it sent out. (Refer to Timing Chart ofTransmitter Control and Flag Timing)

TXC (Input terminal)This is a clock input signal which determines the transfer speed of transmitted data.In synchronous mode, the baud rate will be the same as the frequency of TXC.In asynchronous mode, it is possible to select the baud rate factor by mode instruction.It can be 1, 1/16 or 1/64 the TXC.The falling edge of TXC sifts the serial data out of the MSM82C51A-2.

RXD (input terminal)This is a terminal which receives serial data.

RXRDY (Output terminal)This is a terminal which indicates that the MSM82C51A-2 contains a character that is ready toREAD.If the CPU reads a data character, RXRDY will be reset by the leading edge of RD signal.Unless the CPU reads a data character before the next one is received completely, the precedingdata will be lost. In such a case, an overrun error flag status word will be set.

RXC (Input terminal)This is a clock input signal which determines the transfer speed of received data.In synchronous mode, the baud rate is the same as the frequency of RXC.In asynchronous mode, it is possible to select the baud rate factor by mode instruction.It can be 1, 1/16, 1/64 the RXC.

11/26


SYNDET/BD (Input or output terminal)This is a terminal whose function changes according to mode.In internal synchronous mode. this terminal is at high level, if sync characters are received andsynchronized. If a status word is read, the terminal will be reset.In external synchronous mode, this is an input terminal.A High on this input forces the MSM82C51A-2 to start receiving data characters.In asynchronous mode, this is an output terminal which generates high leveloutput uponthe detection of a break character if receiver data contains a low-level space between thestop bits of two continuous characters. The terminal will be reset, if RXD is at high level.After Reset is active, the terminal will be output at low level.

DSR (Input terminal)This is an input port for MODEM interface. The input status of the terminal can be recognizedby the CPU reading status words.

DTR (Output terminal)This is an output port for MODEM interface. It is possible to set the status of DTR by a command.

CTS (Input terminal)This is an input terminal for MODEM interface which is used for controlling a transmit circuit.The terminal controls data transmission if the device is set in TX Enable status by a command.Data is transmitable if the terminal is at low level.

RTS (Output terminal)This is an output port for MODEM interface. It is possible to set the status RTS by a command.

12/26


ABSOLUTE MAXIMUM RATING

55 to +150

MSM82C51A-2RS

Power Supply Voltage VCC 0.5 to +7 V

Input Voltage VIN 0.5 to VCC +0.5 V

Output Voltage VOUT 0.5 to VCC +0.5 V

Storage Temperature TSTG C

Power Dissipation PD 0.7 W

Parameter UnitSymbol

With respectto GND

Ta = 25C

ConditionsRating

MSM82C51A-2GS MSM82C51A-2JS

0.90.9

OPERATING RANGE

Range

Power Supply Voltage VCC 3 - 6 V

Operating Temperature Top 40 to 85 C


RECOMMENDED OPERATING CONDITIONS

DC CHARACTERISTICS

Typ. Max."L" Output Voltage VOL 0.45 V

"H" Output Voltage VOH V

Parameter UnitSymbol Min.

3.7

IOL = 2.5 mA

IOH = 2.5 mA

Measurement Conditions

Input Leak Current ILI 10 mAOutput Leak Current ILO 10 mA

10

10

0 VIN VCC0 VOUT VCC

Operating SupplyCurrent

5 mAAsynchronous X64 during Transmitting/Receiving

Standby SupplyCurrent

100 mA

ICCO

ICCSAll Input voltage shall be fixed at VCC or GND level.

(VCC = 4.5 to 5.5 V Ta = 40C to +85C)

Typ.

Power Supply Voltage VCC 5 V

Top +25

"L" Input Voltage VIL

"H" Input Voltage VIH

Min.

4.5

40

0.3

2.2

Max.

5.5

+85

+0.8

VCC +0.3


C

V

V

Operating Temperature

13/26


AC CHARACTERISTICS

CPU Bus Interface Part

Max.Address Stable before RD tAR ns

Parameter UnitSymbol Min.20 Note 2

Remarks

Address Hold Time for RD tRA nsRD Pulse Width tRR ns

20

130

Note 2

Data Delay from RD tRD 100 ns RD to Data Float tDF 75 ns10 Recovery Time between RD tRVR tCYAddress Stable before WR tAW ns

6

20

Note 5

Note 2

Address Hold Time for WR tWA ns20 Note 2WR Pulse Width tWW ns100 Data Set-up Time for WR tDW nsData Hold Time for WR tWD ns

100

0

Recovery Time between WR tRVW tCY6 Note 4RESET Pulse Width tRESW tCY6

(VCC = 4.5 to 5.5 V, Ta = 40 to 85C)

14/26


Serial Interface Part

Notes: 1. AC characteristics are measured at 150 pF capacity load as an output load based on 0.8 V atlow level and 2.2 V at high level for output and 1.5 V for input.

2. Addresses are CS and C/D.3. fTX or fRX 1/(30 Tcy) 1 Baud

fTX or fRX 1/(5 Tcy) 16, 64 Baud4. This recovery time is mode Initialization only. Recovery time between command writes for

Asynchronous Mode is 8 tCY and for Synchronous Mode is 18 tCY.Write Data is allowed only when TXRDY = 1.

5. This recovery time is Status read only.Read Data is allowed only when RXRDY = 1.

6. Status update can have a maximum delay of 28 clock periods from event affecting the status.

Max.Main Clock Period tCY ns

Parameter UnitSymbol Min.160 Note 3

Remarks

Clock Low Tme tf ns

Clock High Time tf tCY 50 ns

50

70

Clock Rise/Fall Time tr, tf 20 ns TXD Delay from Falling Edge of TXC tDTX 1 mS

Transmitter Clock Frequency fTX 64 kHz

fTX 615 kHz

DC

DC Note 3

fTX 615 kHzDC

1 Baud16 Baud64 Baud

Transmitter Clock Low Time tTPW tCY1 Baud tTPW tCY

Transmitter Clock High Time tTPD

13

2

15 tCY

16 , 64 Baud1 Baud

tTPD tCY316 , 64 Baud

Receiver Clock Frequency

fRX 64DC kHz1 BaudfRX 615 kHz

fRX 615 kHz

DC

DC

16 Baud64 Baud

Note 3

Receiver Clock Low Time tRPW tCY13 tRPW tCY2

1 Baud16 , 64 Baud

Receiver Clock High Time tRPD tCYtRPD tCY

15

3

1 Baud16 , 64 Baud

Time from the Center of Last Bit to the Rise of TXRDY tTXRDY 8 tCY

Time from the Leading Edge of WR to the Fall of TXRDY tTXRDY CLEAR 400 ns

Time From the Center of Last Bit to the Rise of RXRDY tRXRDY 26 tCY Time from the Leading Edge of RD to the Fallof RXRDY tRXRDY CLEAR 400 ns

Internal SYNDET Delay Time from Rising Edge of RXC tIS 26 tCY

MODEM Control Signal Delay Time from Rising Edge of WR tWC tCY8

MODEM Control Signal Setup Time for Falling Edge of RD tCR tCY20

RXD Setup Time for Rising Edge of RXC (1X Baud) tRXDS tCY11 RXD Hold Time for Falling Edge of RXC (1X Baud) tRXDH tCY17

SYNDET Setup Time for RXC tES tCY18 TXE Delay Time from the Center of Last Bit tTXEMPTY tCY20

(VCC = 4.5 to 5.5 V, Ta = 40 to 85C)

15/26


TIMING CHART

Sytem Clock Input

tf trtf tf tCY

CLK

Receiver Clock and Data

Transmitter Clock and Data

tTPWTXC (1 MODE)

tTPD

tDTX tDTXTXC (16 MODE)

TXD

RXC (1 Mode)tRPW

RXC (16 Mode)

RXD

INT SamplingPulse

(RXBAUD Counter starts here)Start bit

8RXC Periods(16Mode) 16 RXC Periods (16 Mode)

Data bit Data bittRPD

3tCY 3tCY

tf

16/26


Read Control or Input Port Cycle (CPU USART)

Write Control or Output Port Cycle (CPU fi USART)

Read Data Cycle (CPU USART)

tRRtRD tDF

Data Out Active

tAR tRA

tAR tRA

tRXRDY Clear

Data Float Data Float

RD

DATA OUT (D. B.)

RXRDY

CS

C/D

Write Data Cycle (CPU fi USART)

tTXRDY Clear

tDWtWD

tAW tWA

tAW tWA

Data StableDon't Care Don't Care

WR

DATA IN (D. B.)

TXRDY

CS

C/D

tWW

tCR tRR

tRD

tAR tRA

tAR tRA

tDFData FloatData Out ActiveData Float

DSR. CTS

DATA OUT(D. B.)

RD

C/D

CS

DTR. RTS

DATA IN(D. B.)

WR

C/D

CS

tWWtWC

tAW tWA

tAW tWA

Data StableDon't Care Don't Care

tWDtDW

17/26


Transmitter Control and Flag Timing (ASYNC Mode)

DATA CHAR 1 DATA CHAR 2 DATA CHAR 3 DATA CHAR 4

STAR

T BI

T

STO

P BI

T

Wr TxEn Wr SBRK

tTXEMPTY

tTXRDY

CTS

TXEMPTY

TXRDY(STATUS BIT)

TXRDY(PIN)

C/D

WR

TXD 0 1 2 3 4 5 6

Wr DATA 1 Wr DATA 2 Wr DATA 3 Wr DATA 4

Note: The wave-form chart is based on the case of 7-bit data length + parity bit + 2 stop bit.

Transmitter Control and Flag Timing (SYNC Mode)

Receiver Control and Flag Timing (ASYNC Mode)

Data CHAR 1 Data CHAR 2 Data CHAR 3Break

Dat

a Bi

tSt

art B

itSt

op B

itPa

rity

Bit

RxEn Err Res

RxEn

tRXRDYDATACHAR2Lost

Wr RxEn

BREAK DETECTFRAMING ERROR

(Status Bit)OVERRUN ERROR

(Status Bit)RXRDY

C/D

WR

RD

RXDATA

Wr Error

Rd Data

Note: The wave-form chart is based on the case of 7 data bit length + parity bit + 2 stop bit.

0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1

DataCHAR1

DataCHAR2

SYNCCHAR1 SYNC CHAR2

SYNCCHAR3

DataCHAR4

MarkingState

SpacingState

MarkingState

DataCHAR5

SYNCCHAR ETC

PARPARPARPARPARPARPARPAR

Wr CommondSBRK

Wr DataCHAR5

CTS

TXEMPTY

TXRDY(StatusBit)

TXRDY (Pin)

C/D

WR

TXD

Wr DataCHAR1

Marking State

Wr DataCHAR2

Wr DataCHAR3

Wr DataCHAR4

Note: The wave-form chart is based on the case of 5 data bit length + parity bit and 2 synchronous charactors.

18/26


Receiver Control and Flag Timing (SYNC Mode)

x x x x x x 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 0 1 2 3 4 x x x x x x x 0 1 2 3 4 0 1 x 3 4

SYNDET(Pin) (Note 1)

SYNDET (SB)

OVERRUNERROR (SB)

RXRDY (PIN)

C/D

WR

RD

RXD

RXC

Don'tCare

SYNCCHAR 1

SYNCCHAR 2

DataCHAR 1

DataCHAR 2

DataCHAR 3

SYNCCHAR 1

SYNCCHAR 2 Don't Care

DataCHAR 1

DataCHAR 2 ETC

CHAR ASSY Begins

Exit Hunt ModeSet SYNDET

Exit Hunt ModeSet SYNDET (Status bit)

Set SYNDET (Status bit)

CHAR ASSYBegins

Wr EHRxEn

Rd DataCHAR 1

Rd Status Wr Err Res

Rd DataCHAR 3

Rd SYNCCHAR 1

Rd StatusWr EHo

Rd Status

Data CHAR2Lost

tIS tES

(Note 2)

Note:

PAR PAR PAR PAR PAR PAR PAR PAR PAR PAR

1. Internal Synchronization is based on the case of 5 data bit length + parity bit and 2 synchronous charactor.2. External Synchronization is based on the case of 5 data bit length + parity bit.

Note: 1. Half-bit processing for the start bitWhen the MSM82C51A-2 is used in the asynchronous mode, some problems arecaused in the processing for the start bit whose length is smaller than the 1-data bitlength. (See Fig. 1.)

2. Parity flag after a break signal is received (See Fig. 2.)When the MSM82C51A-2 is used in the asynchrous mode, a parity flag may be setwhen the next normal data is read after a break signal is received.A parity flag is set when the rising edge of the break signal (end of the break signal)is changed between the final data bit and the parity bit, through a RXRDY signal maynot be outputted.If this occurs, the parity flag is left set when the next normal dats is received, and thereceived data seems to be a parity error.

Smaller than 7-Receiver Clock Length 16Start bit Length Mode Operation

The short start bit is ignored. (Normal)

Smaller than 31-Receiver Clock Length 648-Receiver Clock Length 16

The short start bit is ignored. (Normal)

Data cannot be received correctly due to a malfunction.

32-Receiver Clock Length 64 Data cannot be received correctly due to a malfunction.9 to 16-Receiver Clock Length 16 The bit is regarded as a start bit. (normal)33 to 64-Receiver Clock Length 64 The bit is regarded as a start bit. (normal)

19/26


Half-bit Processing Timing Chart for the Start bit (Fig. 1)

ST D0 D1 D2 D3 D4 D5 D6 D7 P SP ST D0 D1 D2 D3 D4 D5 D6 D7 P SPRXD

RXRDY

STST D0 D1 D2 D3 D4 D5 D6 D7 P SPRXD

RXRDY

A RXRDY signal is outputted during datareception due to a malfunction.


RXRDY

ST:SP:P:D0 - D7:

Start bitStop bitParity bitData bits


RXRDY

Normal Operation

The Start bit Is Shorter Than a 1/2 Data bit

The Start bit Is a 1/2 Data bit (A problem of MSM82C51A-2)

The Start bit Is Longer Than a 1/2 Data bit

20/26


Break Signal Reception Timing and Parity Flag (Fig. 2)

ST D0 D7 P SP ST D0 D7 P SP ST D0 D1 D2 D3 D4 D5 D6 D7 PBIT POS.

RXD

RXRDY

A parity flag is set, but, no RXRDYsignalis outputted.

SP


RXD

RXRDY

No parity flag is set. and no RXRDY signalis outputted.


RXD

RXRDY

A parity flag is set. and a RXRDY signalis outputted.

SP

Normal Operation

Bug Timing

Normal Operation

SP

21/26


NOTICE ON REPLACING LOW-SPEED DEVICES WITH HIGH-SPEED DEVICES

The conventional low speed devices are replaced by high-speed devices as shown below.When you want to replace your low speed devices with high-speed devices, read the replacementnotice given on the next pages.

High-speed device (New) Low-speed device (Old) Remarks

M80C85AH M80C85A/M80C85A-2 8bit MPUM80C86A-10 M80C86A/M80C86A-2 16bit MPU

M80C88A-10 M80C88A/M80C88A-2 8bit MPU

M82C84A-2 M82C84A/M82C84A-5 Clock generator

M81C55-5 M81C55 RAM.I/O, timerM82C37B-5 M82C37A/M82C37A-5 DMA controller

M82C51A-2 M82C51A USART

M82C53-2 M82C53-5 TimerM82C55A-2 M82C55A-5 PPI

22/26


Differences between MSM82C51A and MSM82C51A-2

1) Manufacturing ProcessThese devices use a 3 m Si-Gate CMOS process technology and have the same chip size.

2) FunctionThese devices have the same logics except for changes in AC characteristics listed in (3-2).

3) Electrical Characteristics3-1) DC Characteristics

Although the output voltage characteristics of these devices are identical, but the measurementconditions of the MSM82C51A-2 are more restricted than the MSM82C51A.

3-2) AC Characteristics

As shown above, the MSM82C51A-2 satisfies the characteristics of the MSM82C51A.

Parameter Symbol MSM82C51A MSM82C51A-2

RD Pulse Width 250 ns minimum 130 ns minimumtRR

RD Rising to Data Difinition 200 ns maximum 100 ns maximumtRD

RD Rising to Data Float 100 ns maximum 75 ns minimumtRF

WR Pulse Width 250 ns minimum 100 ns minimumtWW

Data Setup Time for WR Rising 150 ns minimum 100 ns minimumtDW

Data Hold Time for WR Rising 20 ns minimum 0 ns minimumtWD

Master Clock Period 250 ns minimum 160 ns minimumtCY

Clock Low Time 90 ns minimum 50 ns minimum

Clock High Time120 ns minimum

tCY-90 ns maximum70 ns minimum

tCY-50 ns maximumtf

tf

Parameter Symbol MSM82C51A MSM82C51A-2

VOL measurement conditions +2.0 mA +2.5 mA

VOH measurement conditions -400 mA -2.5 mA

IOL

IOH

23/26


(Unit : mm)

PACKAGE DIMENSIONS

Notes for Mounting the Surface Mount Type Package

The SOP, QFP, TSOP, SOJ, QFJ (PLCC), SHP and BGA are surface mount type packages, whichare very susceptible to heat in reflow mounting and humidity absorbed in storage.Therefore, before you perform reflow mounting, contact Okis responsible sales person for theproduct name, package name, pin number, package code and desired mounting conditions(reflow method, temperature and times).

DIP28-P-600-2.54

Package materialLead frame materialPin treatmentSolder plate thicknessPackage weight (g)

Epoxy resin42 alloySolder plating5 mm or more4.30 TYP.

24/26


(Unit : mm)



QFJ28-P-S450-1.27


Epoxy resinCu alloySolder plating5 mm or more1.00 TYP.

Spherical surface

25/26


(Unit : mm)



SSOP32-P-430-1.00-K


Epoxy resin42 alloySolder plating5 mm or more0.60 TYP.

Mirror finish

26/26


4) Notices on use

Note the following when replacing devices as the ASYNC pin is differently treated between theMSM82C84A and the MSM82C84A-5/MSM82C84A-2:

Case 1: When only a pullup resistor is externally connected to.The MSM82C84A can be replaced by the MSM82C84A-2.

Case 2: When only pulldown resistor is externally connected to.When the pulldown resistor is 8 kiloohms or less, the MSM82C84A can be replaced by theMSM82C84A-2.When the pulldown resistor is greater than 8 kiloohms, use a pulldown resistor of 8 kiloohms or less.

Case 3: When an output of the other IC device is connected to the device.The MSM82C84A can be replaced by the MSM82C84A-2 when the IOL pin of the device to drive theASYNC pin of the MSM82C84A-2 has an allowance of 100 mA or more.

04- OKI 8251 (USART)

Documents

Transcript of 04- OKI 8251 (USART)