Post on 23-Feb-2016
description
“The Nation’s Best Read Construction Newspaper… Founded 1957.”
® WesternEdition
$3.00
AED Holds Annual Summit,
CONDEX Show...8
ASCO Raises Money for
Wounded Warriors...12
Inside
JCB Helps to Unearth
Buried Spitfires...26
February 9, 2013 • Vol. IX • No.3 • 470 Maryland Drive • Ft. Washington, PA 19034 • 215/885-2900 • Toll Free 800-523-2200 • Fax 215/885-2910
www.constructionequipmentguide.comPublished Nationally
SALEM, Ore. (AP) The OregonTransportation Commission on Jan. 16approved an additional $142 millionfor an expensive, trouble-plaguedproject to realign a section of U.S.Highway 20 through the Coast Range. The stretch of highway links
Corvallis and Newport. The vote allows the state
Transportation Department to proceedwith work to replace a twisty 10-mi.
(16 km) portion of the highway nearEddyville with a straighter, safer 5.5-mi. (8.8 km) route. The project was originally estimat-
ed to cost $140 million. With Jan. 16’smoney infusion, the estimated cost is$366 million. Work began in 2005with completion expected by 2009.Now the targeted finish date has beenmoved back to 2016 at the earliest.
Additional Funds...
Ore. Commission Approves$142M for Highway 20 Job
Lori LovelyCEG CORRESPONDENT
The Texas Rangers are at it again. Another series ofupgrades to Rangers Ballpark in Arlington is underway. “This is the third year of projects,” said Rob Matwick,
vice president, ballpark communications. “We’re at themidpoint [of construction].”During the off-season in 2010, a new scoreboard and
800 high-definition TVs were installed and a completeoverhaul of the in-park audio and video systems was per-formed. The following year, work focused on centerfield, which
Matwick said was rebuilt in 4 and a half months. It cost$12.5 million and was the most extensive renovation inthe history of the park, according to CEO and PresidentNolan Ryan. “It was the first big physical change since 1994,”
Matwick said. In fact, the Vandergriff Plaza project repre-sents the first major structural renovation at RangersBallpark since the Cuervo Club was added behind thehome plate section of the lower seating bowl in 2000.
Second Inning Last year’s renovation was well-received by the fans,
especially during the heat of summer, Matwick said.Many of the features were designed with them in mind,
Texas Rangers Ballpark Upgrades, Take 3
Significantly more construction firms are planning toadd new staff than plan to cut staff while demand for manytypes of private sector construction projects shouldincrease this year according to survey results released Jan.15 by the Associated General Contractors of America andComputer Guidance Corporation. The survey, conductedas part of Tentative Signs of a Recovery: The 2013Construction Industry Hiring and Business Outlook, pro-vides a generally optimistic outlook for the year even asfirms worry about rising costs and declining public sectordemand for construction.
Firms Optimistic:Outlook for 2013Appears Strong
see COMMISSION page 42
see OUTLOOK page 16
see RANGERS page 44
A third row of home plate seats will be added in front of the two existing rowsof premium seating built for the 2009 season.
Table of Contents................4
Recycling Section ........13-21
Attachment Section ....27-29
Truck & Trailer Section ..............................................36-38
Business Calendar ............38
Auction Section ..........40-45
Advertisers Index..............46
Page 2 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
SAVE TIME • SAVE MONEY • SAVE LABOR • SAVE OIL
• No tools required• No expensive
hardware needed• No more rags
stuffed into hoses• No more messy
plastic caps• The ultimate
contamination control tool• One hand installation• Eliminate hydraulic
oil spills & clean up• Quick installation
& ease of usage• Safe for personnel
& environment• Industry acclaimed• 100% Made in USA
For more information contact Mike Pearl at914.980.8890 or email mike @ flangelock.comwww.flangelock.com
A R E N O T O P T I O N A LA N D A R D S Y O U R S T
.A R E N O T O P T I O N A L
.growneyinc.comwwwout more at
one manufacturer with standards as high as yours. ylnos’erehT.evorppa
From startup to shutdown, you stay clean and comfortable. W
provide a best-in-class, pressurized environment that keeps dust to a
s’tacboBhtiwecinytterp
, dusty job isn’t so A dirty
relae Dtacb BoedzirothuA
.growneyinc.com
one manufacturer with standards as high as yours.
From startup to shutdown, you stay clean and comfortable. W
provide a best-in-class, pressurized environment that keeps dust to a
ved door pocket and one-piece seal. Theycur,euqinus
o bad when you’ve got room to breathe. In fact, it’
dniFone manufacturer with standards as high as yours.
e think you’llFrom startup to shutdown, you stay clean and comfortable. W
.muminimprovide a best-in-class, pressurized environment that keeps dust to a
ved door pocket and one-piece seal. They
s athe. In fact, it’
GmoT
aF1
097-848-805 5:xaF00924-88-055
7917 8M Ne,uqeruqlbuA.E.d Naoa Riraledna1 C032
relae Dtacb BoedzirothuA
omc.cniyenwogr.www
In,tnpmeiu Eqyenwor G
926-923-505M 8, NsbboH
et Bse0 W042
01116-23-5059947 8M Nn,otginmra
d aog Rniy Kor0 T01
c. In
33118-95-5197399X 7, Tosal PE
s ajo3 R2311
3921428r edne
#|ved.. All Rights Reser©2011 Bobcat Company and the Bobcat logo are registered trademarks of Bobcat Company in the United States and various other countries.®Bobcat
614B # and the Bobcat logo are registered trademarks of Bobcat Company in the United States and various other countries.
and the Bobcat logo are registered trademarks of Bobcat Company in the United States and various other countries.
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 3
2004 JCB 506, Stk# 8432, OROPS, 6,000 lbs.,36 ft., 3,372 hrs., 4WD, 4WS, 48" Forks, 53"Frame, Aux. Hyd., Hyd. Leveling System, 4 Cyl.JCB Eng., wt. 20,270 lbs.......................$21,500
2007 Cat 247B, Stk# 8171, OROPS, 2115 Hrs,70” Bkt, 15” Rubber Tracks, 4 Cyl. Perkins Eng,Aux Hyd ................................................$26,500
2008 Cat 330DL, Stk# 8323, EROPS, A/C, 4,635hrs., 52" Bucket, 34" Pads, 11' 4" Wide ..........................................................................$155,500
2004 Kubota KX91-2, Stk# 8441, OROPS, 5,587hrs., 90° Boom, 12" Bucket, 12" Rubber Tracks,59" Blade, 4 Cyl. Kubota Eng.................$10,500
2002 Takeuchi TB016, Stk# 8227, OROPS, 2,801hrs., 18" Bucket, Aux. Hyd., 9" Rubber Tracks, 39"Blade, 3 Cyl. YanMar Eng........................$9,500
1999 Cat 140HVP, Stk# 8285, EROPS, A/C,15,354 Hrs, 14’ M/B, 14.00Rx24 Tires, 10’3”Height, 8’ Wide..........................................$99,500
2006 Cat 308C, Stk# 8402, EROPS, 3,713 hrs.,29" Bucket, 8' 1" Blade, 24" Pads, 8' 2" Wide, 4Cyl. Mits. Eng. ........................................$39,500
2009 Cat 329DL, Stk# 8361, EROPS, A/C,Stereo, 4,510 hrs., 80% U/C, 52" Bucket, 32"Pads, 11' 2" Wide................................$149,500
2006 John Deere 650J LT, Stk# 8181, EROPS,A/C, Sweeps, 6-Way Blade, 2077 Hrs, 75% U/C,18” Pads, 8’9” Wide ..............................$67,500
1997 Skytrack 8042, Stk# 8327, 8,000 lbs., 42ft. 5,107 hrs., 4WD, 4WS, 48" Forks, 72" Frame,Aux. Hyd., Hyd. Self Leveling System, 13.00x24Tires ......................................................$28,500
2006 Multiquip MQ Power, Stk# 8151, 191 hrs.,25KVA, 14KW, 175x80D13 Tires, 4 Cyl. Izusu Eng....................................................................$9,500
2006 Ingersoll-Rand SD70D TF, Stk# 8383, 66"Smooth Drum, 1,133 hrs., 14.9X24 Tires, 4 Cyl.Cummins Eng............................................$40,500
2008 Cat 226B Series II, Stk# 8279, OROPS,1,191 hrs., 67" Bucket, Aux. Hyd., 13" RubberTracks, 4 Cyl. Cat Eng. ..........................$21,500
2008 Cat D5K XL, Stk# 8386, OROPS, 6 WayBlade, 3,516 hrs., 20" Pads, 9' 6" Wide $62,500
2007 Case 95XT, Stk# 8453, EROPS, A/C, 930hrs., with Magnum Mulching Head, s#1655195with Bradco Carbide Teeth, w/Dirt Bucket, Aux.Hyd., 12x16.5 Tires with Metal Tracks ..$49,500
2005 Case 865, Stk# 8411, 7,883 hrs., EROPS,A/C, 8.3 Cummins Turbo Charge Eng., 14.00x24Tires, Rear Ripper .....................................$89,500
2006 Terex TH644C, Stk# 7931, EROPS A/C &Heat, 6,000 lbs., 44 ft., 4WD, 4WS, 3,155 hrs.,13x24 Foam Filled Tires, 48" Forks, 50" Frame, 4Cyl. JD Eng.............................................$32,500
2012 Doosan DX225LC, Stk# 8340, EROPS, A/C,FM Stereo, 11 hrs., 46" Bucket, 32" Pads, 10' 6"Wide, Doosan Eng...................................$139,500
2003 Takeuchi TB53FR, Stk# 8143, EROPS,5657 Hrs, 23” Bkt, Aux. Hyd, 16” Rubber Tracks,78” Blade, 4 Cyl. YanMar Eng ..............$24,500
2008 Cat 301.8, Stk# 8204, OROPS, 1,188 hrs.,16" Bucket, Aux. Hyd., 9" Rubber Tracks, 53"Blade, 3 Cyl. Mitsubishi Eng ................$17,500
2009 Cat D5K LGP, Stk# 8262, EROPS, A/C,Sweeps, 6 Way Blade, 2,822 hrs., 26" Pads, 10'6" Blade ................................................$89,500
2007 Atlas Copco 185CFM, Stk# 8434, 2,292hrs., PSI 133, ST205x75Dx15 Tires, JD Eng., wt.1,133 lbs. ................................................$8,500
2009 Cat 336DL, Stk# 8366, EROPS, A/C, FMStereo, 4,660 hrs., 80% U/C, 64" Bucket, 34"Pads, 11' 3" Wide.................................$169,500
2009 Cat D8T, Stk# 8233, EROPS, A/C, RearScreen, St/Tilt Blade, 2,834 hrs., 28" Pads, 75%U/C, Allied W12E Winch, 11' 4" Ht., 9' 7" Track toTrack, 11'6" w/Frame, 16'4" Blade ......$425,000
2006 JCB VM46D, Stk# 8431, OROPS, 54"Smooth Drum with Pad Drum Shell Kit, 1,019hrs., 12.00R20 Tires, 4 Cyl. Cummins Eng. ....................................................................$22,500
2005 Cat D6R II LGP, Stk# 8047, EROPS, A/C,Sweeps, Rear Screen, St./Tilt Blade, 7415 Hrs,95% U/C, w/Winch, 13’ Blade ............$129,500
2009 Cat D8T, Stk# 8117, EROPS, A/C, Semi UBlade w/Hyd. Tilt, 2,515 hrs., 80% U/C, RearRipper s/n TDD01421, 24" Pads, 11' 8" Height ................................................................$475,000
2011 Cat 420E, Stk# 8420, EROPS, A/C & Heat,4WD, 1,399 hrs. 23" Bucket, Pilot Controls,12.5x80x18 Front Tires, 19.5Lx24 Rear Tires ..................................................................$76,500
2006 Skytrak 10054, Stk# 8258, 10,000 lbs., 54ft., 2,752 hrs., 4WD, 4WS, 48" Forks, 52" Frame,Aux. Hyd., Hyd. Self Leveling System, 4 Cyl.Cummins Eng............................................$59,500
2006 John Deere 650J LGP, Stk# 8137, EROPS,A/C, FM Stereo, Forestry Package, 6-Way Blade,4725 Hrs, 10’9” Blade ..........................$69,500
2009 Cat 336DL, Stk# 8341, EROPS, A/C, FMStereo, 3331 Hrs, 57” Bkt, 34” Pads, 11’4” Wide............................................................$179,000
2008 Cat D6K XL, Stk# 8231, OROPS, 6 WayBlade, Sweeps, Rear & Side Screens, 6 WayBlade, 1,847 hrs., 80% U/C, Cat PA50-82VEWinch s/n 0701480, 22" Pads, 10 ft. Blade ....................................................................$109,000
2006 John Deere 650J, Stk# 8345, EROPS, A/C,FM Stereo, Sweeps & Screens, 6 Way Blade, 95% U/C, 5,331 hrs., 18" Pads, 8' 9" Blade$56,500
"In Business for over 30 Years"www.hendrixmachineryllc.com
1-936-327-5430 • Email: sales@hendrixmachineryllc.com Se HablaEspañol
2007 Ditch Witch RT40, Stk# 8394, OROPS, 797hrs., 6 WB, 64" Blade, Slide Boom Shift, 6" Trench,29x12.50x15 Tires, 3 Cyl. Deutz Eng. ....$15,500
2001 John Deere 410G, Stk# 8396, EROPS, A/C& Heat, 2WD, 3,628 hrs., Extendahoe, 2 StickControls, 18" Bucket, 19.5Lx24 Rear Tires,11Lx16 Front Tires ..............................$25,500
2006 John Deere 650J LGP, Stk# 8404, HYSTAT,OROPS, Eng. Encl., 6 Way Blade, 5,089 hrs.,70% U/C, 28" Pads, 10' 9" Blade...........$38,500
2005 Case 865, Stk# 8411, EROPS, A/C, 784 hrs.,(6 Cyl.) 8.3 Cummins Turbo Charge Eng.,14.00x24 Tires, Rear Ripper, 13 ft. Blade, 10' 5"Height, 8' 5" Wide ....................................$89,500
Page 4 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
WESTERN EDITIONCirculated Throughout • Alaska • Arizona • California • Colorado • Hawaii
• Idaho • Montana • New Mexico • Nevada • Oklahoma • Oregon • Texas • Utah • Washington • Wyoming
Founder, Publisher & CEO Edwin M. McKeon Sr.Western Publisher Edwin M. McKeon Jr.
Editor In Chief Craig Mongeau Associate Editor Christine Reckner
Editorial Consultant Pete Sigmund Production Mgr. John Pinkerton
Controller Tom WeinmannCirculation Mgr. Rolf Krog
Asst. Circulation Mgr. Cathy Printz
Main office 470 Maryland Drive Fort Washington, PA 19034 215/885-2900
Toll Free 800/523-2200 Fax 215/885-2910
Web site www.constructionequipmentguide.comEditorial e-mail editorial@cegltd.com
Advertising e-mail production@cegltd.com
For advertising rates: Contact Edwin M. McKeon Jr.National Sales Manager
215/885-2900Toll Free 800/523-2200
Fax 215/885-2910e-mail tmckeon@cegltd.com
Contact Dale Agnew• Arizona • Colorado • New Mexico • Oklahoma
• Texas • Wyoming
Toll Free 877/877-4997 Fax 972/695-6049
e-mail dagnew@cegltd.com
Contact Frank Strazzulla• Alaska • California • Hawaii • Nevada • Oregon• Utah • Washington
949/459-1767Fax 949/203-2859
e-mail fstrazzulla@cegltd.com
Contact Patrick Kiel• Idaho • Montana
Toll Free 866/413-4265Fax 952/353-2750
e-mail pkiel@cegltd.com
Construction Equipment Guide Western Edition is published bi-weekly by Construction Equipment Guide Ltd. Advertisingand Editorial Offices are located at 470 Maryland Dr., Ft. Washington, PA 19034. Toll Free 800/523-2200 or Fax215/885-2910. Annual Subscription Rate $65.00. Call for Canadian and foreign rates.
Application to mail at periodicals postage prices is pending at Ft. Washington, PA and at additional mailing offices.POSTMASTER: Send address changes to Construction Equipment Guide Western Edition, 470 Maryland Dr, Ft.Washington, PA 19034.
Contents Copyrighted ©2013, by Construction Equipment Guide, which is a Registered Trademark, registered in theU.S. Patent Office. Registration number 0957323. All rights reserved, nothing may be reprinted or reproduced (includ-ing framing) in whole or part without written permission from the publisher. All editorial material, photographs, draw-ings, letters, and other material will be treated as unconditionally assigned for publication and copyright purposes andare subject to Construction Equipment Guide's unrestricted right to edit and comment editorially. Contributor articles donot necessarily reflect the policy or opinions of this publication.
Call or write for advertising rates, publication schedule and media kit. The Construction Equipment Guide is not respon-sible for clerical or printer's errors, every care is taken to avoid mistakes. Photographs of equipment used in advertise-ments are not necessarily actual photographs of the specific machine. Similar photographs are used occasionally andevery effort is taken to depict the actual equipment advertised. The right is reserved to reject any advertising.
IN THIS ISSUESPECIAL SECTION…RECYCLING, CRUSHING AND SCREENINGBe sure to check out this special section! Keep up to date with the latest information on recycling, crushing and screening.
FEATURES…MUSTANG CAT MADE EQUIPMENT PROVIDER ATLIVESTOCK SHOWMustang CAT has provided equipment to the event for almost 40 years andlooks forward to continuing this relationship for many years to come.
ASSOCIATED EQUIPMENT DISTRIBUTORS HOLDSANNUAL SHOWThe annual Associated Equipment Distributors (AED) Summit and CONDEXshow was held Jan. 14 to 17 in Las Vegas.
ASCO EQUIPMENT PRESENTS $130,515 CHECK TOCOMBAT MARINE OUTDOORSThe check resulted from a yearlong effort by local employees in ASCOlocations throughout Texas to benefit CMO in 2012.
ROAD MACHINERY WELCOMES TWO HIRES,PROMOTES ANOTHERRoad Machinery has recently welcomed two hires, Rick Dennis and BillSchwenk. The company also has promoted Mark Caldwell to regionalgeneral manager.
JCB MACHINES TO HELP UNEARTH BURIEDWARTIME SPITFIRESTwo excavators and a backhoe made by Staffordshire-based JCB are aboutto embark on a mission to help recover Spitfire warplanes designed by oneof the county’s most famous sons and believed to be buried in Burma.
STAGE 8 MECHANICAL LOCKING FASTENERS STAYTIGHT ON TRUCKS Stage 8, an active mechanical locking systems manufacturer, now hasapplications that keep work trucks on the road.
CAT LIFT PROVIDES TRUCKS FOR 2013 HOUSTONLIVESTOCK SHOWBehind the scenes Cat Lift Trucks will provide the equipment and expertise,including more than 100 lift trucks, needed to prepare for the
12
26
12
8
6
13
35 CLASSIFIEDS38 BUSINESS CALENDAR40 COMING AUCTIONS
EQUIPMENT…27 PNEUMATIC Concrete Dowel Drills37 GRASAN Secondary Crushing Plants
8
8
12
26
13
37
38
®
Mobile LinkedIn Facebook Twitter YouTube
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 5
ROSCO DISTRIBUTOR
ROAD WIDENER
LEEBOY PAVER
MOTOR GRADERS
ROSCO CHIPPER
ASPHALT ROLLERS
ROSCO ROAD BROOM PATCH TRUCKS
If you’re looking for paving, chip seal or street reconstruction, look to MACDONALD EQUIPMENT for all of your equipment needs.
Your one stop shopping dealer.
MACDONALD EQUIPMENT
P.O. Box 18657333 HIGHWAY 85
COMMERCE CITY, CO 80037
P: 303-287-7401F: 303-287-7404
Page 6 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
Mustang CAT, the Caterpillar equipment and engine deal-er for southeast Texas, has signed on as the official providerof construction equipment to the Houston Livestock Showand Rodeo. Mustang CAT has provided equipment to theevent for almost 40 years and looks forward to continuingthis relationship for many years to come.
“We are thrilled to partner with the Houston LivestockShow and Rodeo,” said Brad Tucker, president of MustangCAT.
“This organization has helped thousands of Texas studentsby awarding more than $330 million toward scholarshipsand educational programs. The show is one of the biggestevents of the year in Houston and is consistently ranked asthe world’s largest rodeo. We are very proud to be a part ofan event that has such a rich heritage in Houston and hasdone so much for the youth of Texas and the city ofHouston.”
Mustang will provide the Houston Livestock Show andRodeo with a wide variety of equipment including articulat-ed haul trucks, compactors, dozers, excavators, motor-graders, skid steer loaders, telehandlers, wheel loaders andgenerators ranging from 30-175 kw to use for hauling, con-struction, and maneuvering large items.
The Houston Livestock Show and Rodeo will be held Feb.25 through March 17 at the Reliant Center.
Mustang CAT MadeEquipment Providerat Livestock Show
Visit www.sealsaver.comfor more information or contact us at
1-800-683-5189
Exclusively manufactured by:
Fluid ControlServices, Inc.1155 Allgood Road • Suite 15
Marietta, GA 30062
1-800-683-5189Fax: 770-509-5832
SEAL SAVER has proven effective inConstruction, Mining, Waste Management,Quarries, Refineries, Marinas, Recycling,Wood Products Processing, Steel Mills
and Hot Slag Industries.
SatisfactionGuaranteed!
SEAL SAVER PROTECTIVECYLINDER COVER
KOMATSUD65EX-15
STOP the never ending cycle of cylinder repairs.
Made inthe USA
The SEAL SAVER WILL:Protect cylinders from the elements • Eliminate dings and dents from fallingdebris • Reduce particle contamination of hydraulic systems • Prevent pitting due to chemical washes • Extend the lifeof cylinder seals • Eliminate rod scoring
To2
!morFFre sohoC
C LLLA AS)6688(
WWWW R
MA RO GUOD584 - 0817
BR DESU MOC
WWWW R.
BR DESU . MOC
We Can Help You Reduce Your Risk of
Equipment Theft
Visit us at the following conferences to learn more:
World of ConcreteLas Vegas Expo CenterLas Vegas, NevadaFebruary 5-8, 2013Booth # C4023
For more information:call 1-866-663-7872 or visit www.ner.net© Verisk Crime Analytics, Inc., 2013. All rights reserved. NER is a division of Verisk Crime Analytics, Inc. HELPtech, IRONcheck, NER, and the NER logo are registered trademarks and IRONwatch is a trademark of Verisk Crime Analytics, Inc.
The Rental ShowSands Expo & Convention CenterLas Vegas, NevadaFebruary 10-13, 2013Booth # 2630
Over a billion dollars worth of construction equipment is stolen in the United States each year.
Since 2001, NER has helped equipment owners manage equipment risk throughHELPtech, a equipment marking andregistration program, IRONcheck, a machine-history search for usedequipment, and IRONwatch, ano-monthly-fee GPS trackingand recovery device.
e Can Help YW
educe Y R Y Y
Risk ofeduce Y
Equipment Te Can Help YW
owners manage equipment risk throughSince 2001, NER has helped equipment
is stolen in the United States each yearOver a billion dollars worth of construction equipment
pment Teduce You R p Y You R
pment risk t s helped equ
d States eac worth of con
heft TRisk ofour Y Your
egas Expo CenterLas Vorld of ConcreteW
isit us at the following confereVVisit us at the following confereand recovery device.no-monthly-fee GPS trackingequipment, and IRONwatch, aa machine-history search for usedregistration program, IRONcheck, HELPtech, a equipment marking and
egas Expo Center
wing confere
no-monthly-fee GPS trackingequipment, and IRONwatch, a arch for use
IRONcheck ent marking
Sands Expo & Convention CenterThe Rental Show
Sands Expo & Convention CenterThe Rental Show
Booth # C4023February 5-8, 2013
egas, NevadaLas Vegas Expo CenterLas V
NER, and the NER logo are registered trademarks and IRONwatch is a trademark of V© V
call For more information:
egas Expo Center
Booth # 2630February 10-13, 2013
egas, NevadaLas VSands Expo & Convention Center
NER, and the NER logo are registered trademarks and IRONwatch is a trademark of VAll rights reserved. NER is a division of VAnalytics, Inc., 2013. erisk Crime © V
or visit 1-866-663-7872call For more information:
February 10-13, 2013egas, Nevada
Sands Expo & Convention Center
Analytics, Inc.erisk Crime NER, and the NER logo are registered trademarks and IRONwatch is a trademark of VAnalytics, Inc. HELPtech, IRONcheck, erisk Crime All rights reserved. NER is a division of V
.net.nerr.netwww or visit
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 7
Komatsu Distributor
ContactAllen Stokke
Used Equipment Manager866-400-5250
astokke@roadmachinery.com
www.roadmachinery.com/equipmentWirtgen • Hamm • Vogele • Kleemann • Finn • Terex-Fuch
DozersKOMATSU D65EX-15EO, 2008, EMD7946, 3724 Hrs ......................................................CALL
KOMATSU D61EX-15, 2007, EMD293, 2801 Hrs ........................................................$149,000
KOMATSU D51EX-22, 2007, EMD7022, 2726 Hrs ......................................................$119,000
KOMATSU D39EX-22, 2011, EMD6862, 277 Hrs ..............................................................CALL
KOMATSU D65EX-15EO, 2006, EMD8788, 2963 Hrs ......................................................CALL
KOMATSU D39EX-21A, 2003, EMD7752, 3169 Hrs..........................................................CALL
Excavators CrawlersKOMATSU PC400LC-7L, 2005, EMD247, 6012 Hrs ....................................................$165,000
KOMATSU PC400LC-7L, 2004, EMD249, 6501 Hrs ....................................................$135,000
KOMATSU PC800LC-8, 2007, EMD6888, 4578 Hrs ....................................................$550,000
KOMATSU PC200LC-8, 2008, EMD109, 2040 Hrs ......................................................$135,000
KOMATSU PC78MR-6, 2006, EMD8662, 2950 Hrs........................................................$52,000
KOMATSU HB215LC-1, 2011, EMD7061, 210 Hrs ............................................................CALL
KOMATSU PC200LC-8, 2010, EMD7124, 1123 Hrs ....................................................$135,000
KOMATSU PC220LC-8, 2007, EMD67, 2477 Hrs ........................................................$149,000
KOMATSU PC300HD-8, 2008, EMD8663, 4760 Hrs ....................................................$145,000
KOMATSU PC300LC-7EO, 2007, EMD252, 4603 Hrs ................................................$165,000
Wheel LoadersKOMATSU WA320-3MC, 1999, EMD8714, 11347 Hrs ......................................................CALL
KOMATSU WA320-3MC, 2001, EMD7052, 6098 Hrs ....................................................$69,500
KOMATSU WA500-6, 2007, EMD7624, 6384 Hrs ........................................................$229,000
KOMATSU WA450-3, 2000, EMD8295, 6265 Hrs ..........................................................$92,500
KOMATSU WA320-5, 2006, EMD7787, 4055 Hrs ........................................................$115,000
Moving On…
USDOT SecretaryLaHood to LeaveObama AdminBy Ken ThomasASSOCIATED PRESS
Transportation Secretary Ray LaHood, the onlyRepublican still left in President Barack Obama’s first-termCabinet, said he plans to leave the Obama administration. The former congressman from Illinois said in an interview
with The Associated Press that he intends to remain at thedepartment until his successor is confirmed. LaHood has helped the Obama administration steer
through a number of safety measures and highway projectsduring the past four years. His record has included steps tocurb distracted driving, promote high-speed rail projects andimprove roads and bridges. Former Defense Secretary Robert Gates also was a
Republican. LaHood said he will not run for public office in his home
state of Illinois, saying he believes “you should go out whilethey’re applauding.”
it’s not
’sby TheShelterPetProject.orgfault
Obama Admin to ConfrontOil Pipeline, Climate ChangeBy Matthew DalyASSOCIATED PRESS
WASHINGTON (AP) President BarackObama’s second-term energy agenda is tak-ing shape and, despite the departure of keyCabinet officials, it looks a lot like the first:more reliance on renewable energy sources,such as wind and solar, and expanded pro-duction of oil and natural gas. Obama also ispromising to address climate change, anissue he has acknowledged was sometimesoverlooked during his first term. “The president has been clear that tackling
climate change and enhancing energy secu-rity will be among his top priorities in hissecond term,” said Clark Stevens, a WhiteHouse spokesman. While the administration has made
progress in developing renewable energyand improving fuel-efficiency standards forvehicles, “we know there is more work todo,” Stevens said. He will have to do that work with new
heads of the agencies responsible for theenvironment. Interior Secretary Ken Salazar,Environmental Protection chief Lisa Jacksonand Jane Lubchenco, head of the NationalOceanic and Atmospheric Administration,have announced they are leaving. EnergySecretary Steven Chu is expected to followhis colleagues out the door in coming weeks. The White House said no decisions have
been made on replacements for any of theenvironment and energy jobs but saidObama’s priorities will remain unchanged. One of the first challenges Obama will
face is an old problem: whether to approvethe Keystone XL oil pipeline from Canada toTexas. Obama blocked the pipeline last year,citing uncertainty over the conduit’s routethrough environmentally sensitive land inthe midwest state of Nebraska. Gov. DaveHeineman is considering a new route; he isexpected to make a decision in February. The State Department has federal jurisdic-
tion because the $7 billion pipeline begins inCanada. The pipeline has become a flashpoint in a
bitter partisan dispute. Republicans andmany business groups say the project wouldhelp achieve energy independence for NorthAmerica and create thousands of jobs. But environmental groups have urged
Obama to block the pipeline, which they saywould transport “dirty oil” from tar sands inwestern Canada and produce heat-trappinggases that contribute to global warming.They also worry about a possible spill. If the pipeline is approved, “the adminis-
tration would be actively supporting andencouraging the growth of an industry whichhas demonstrably serious effects on cli-mate,” 18 top climate scientists wrote in aletter to Obama. Obama also faces a choice over whether
to promote a boom in oil and natural gas pro-duction that has hampered growth of nontra-ditional energy sources such as wind andsolar. The emergence of cheap, plentiful natural
gas in particular poses a dilemma forObama, who supports gas development as acleaner alternative to fossil fuels that triggerglobal warming. Many environmental groups who support
the president are wary of natural gas and arecritical of drilling techniques such ashydraulic fracturing that allow drillers togain access to reserves that formerly wereout of reach. Hydraulic fracturing, alsoknown as “fracking,” involves injection ofwater, sand and chemicals underground tobreak up dense rock that holds oil and gas. The Obama administration has said it will
for the first time require companies drillingfor oil and natural gas on public and Indianlands to publicly disclose chemicals used infracking operations. The proposed rules alsowould set standards for proper constructionof wells and wastewater disposal. Environmental groups are pushing the
administration to do more to crack down onfracking, while industry groups andRepublican lawmakers say federal rules areunnecessary, since states already regulate thedrilling practice. The natural gas boom “puts the adminis-
tration in an interesting position. They can beaggressive and look at natural gas for thepossibilities it brings, or they can bow to theenvironmental community, which is notinterested in more natural gas drilling,” saidFrank Maisano, a Washington spokesman ofa range of energy producers from coal towind. The Environmental Protection Agency
also is expected to forge ahead with the firstlimits on carbon pollution from coal-firedpower plants. The administration hasimposed rules on new plants but is expectedto move forward on rules for existing plants,despite protests from industry andRepublicans that new rules will raise elec-tricity prices and kill off coal, the dominantU.S. energy source. Older coal-fired power plants have been
shutting down across the country, due to lownatural gas prices and weaker demand forelectricity.
Page 8 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
Associated Equipment Distributors Hold Annual Show
John Gaughan (L) and Eric Briese, both of TVHParts Co., Olathe, Kan. TVH, well known in theforklift industry, is now entering the construc-tion industry.
Displaying the Magnum MS-4 HFB are David Hughes (L),Magnum Attachments, Etobicoke, Ontario; and Tom Bottrell,company president.
(L-R): Bobby Hudson and Robbie Hegwood, both ofHydrauliCircuit Technology Inc., answer questionsfrom David Mehrtens, RoadBuilders Machinery andSupply Co. Inc.
Barry Stoughton (R), president, BLS Enterprises,shows his track pads to Bill Lyon (L) and Rick Albert,president, Rick Albert Machinery, Pleasanton, Calif.
(L-R): The father and son team of Bryan and PhilMcCoy, RoadBuilders Machinery and Supply Co. Inc.,visit the IronPlanet booth and speak with CarsonErickson, sales manager, IronPlanet.
The annual Associated Equipment Distributors (AED)Summit and CONDEX show was held Jan. 14 to 17 inLas Vegas.
Keynote speakers John Hofmeister, founder and CEO ofCitizens for Affordable Energy; Fox News Channel’s Stuart
Varney; and Eli Lustgarten, senior vice president ofLongbow Securities and president of ESL Consultantsaddressed attendees and dealer and manufacturer representa-tives manned the booths on all days of the event.
Woods Equipment Co., headquartered in Oregon, Ill., had its new Woods variablecoupler on display, which drew a lot of traffic to the booth. (L-R) are Don Kemp,MinnPar, Mounds View, Minn.; Jerry Johnson and Doreen Putnam, WoodsEquipment Co.; and Bill Grundy, Avant Tecno USA, Elk Grove Village, Ill.
see AED page 34
Hydrema introduces the new model 912 flatbed truck to address another uniqueniche in the off-road construction truck market. (L-R) are Alan Patterson, AlbertaConstruction Equipment; Chris Binder, executive vice president, Hydrema; KevinO’Donnell, national sales manager, Hydrema; Sterling Roberts, national servicemanager, Hydrema; and Tom Hartman, regional business manager, Hydrema.
Bagela is quickly becoming the recognized leader ofasphalt recycling equipment in North America.Representing the company are Bagela’s Dan Kovalick(L) and Greg Harla.
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 9
1995 Komatsu PC250LC-6; #91777, Aux Hyd,Mech Thumb, 31.5” Tracks, 10,000 hrs$49,500
2003 Komatsu WA180-3; #91673, Cab/AC,Ride Control, QC/Bucket, 8,800 hrs ......$47,500
2001 Komatsu WA380-3; #81866, Cab/AC,Ride Control, QC/BKT/Forks, 8,300 hrs $79,500
1996 Komatsu WA250-1; #91810, Cab/AC, GPBucket, 20.5-25 Tires ............................$34,500
1994 Komatsu PC200LC-6; #91806, Cab/AC, 9’6” Arm, 31.5” Tracks, 6,800 hrs ..........$47,500
2003 Caterpillar D6N LGP; #91804, Cab/AC,Good U/C, Trimble System....................$98,500
2003 Caterpillar D6R XL II; #91695, Cab,Sweeps, 26” Tracks, 14,500 hrs ........$104,500
2002 Caterpillar 769D; #81825, Cab/AC,18:00-33 Tires, Approx 10,000 hrs ....$269,500
2001 Caterpillar 730; #91650, Cab/AC, 23.5-25Tires, 12,400 Hrs ..................................$99,500
2002 Komatsu PC300LC-6; #91646, Cab/AC, 13’Arm, QC, 33.5” Tracks, 10,650 hrs ......$76,500
2001 Komatsu WA180PT-3; #91793, Cab/AC,GP Bucket, 17.5-25 Tires, 9,450 hrs ....$34,500
2006 Komatsu WA600-3; #81553, Cab/AC,Ride Control, 8 yd BKT, 3,400 hrs ......$399,500
Call Doug / Sam:(866) 485-7180
Page 10 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
Allis-Chalmers Forest Green HD21 Dozer/Ripper, 1:50
Scale......................................................................................$90
Allis-Chalmers Orange HD21 Dozer/Ripper, 1:50 Scale $90
Allis-Chalmers Yellow HD21 Dozer/Ripper, 1:50 Scale ..$90
Bantam C-35 Crawler Shovel, 1:50 Scale ......................$70
Bantam Truck Mounted Crane, 1:50 Scale ..................$125
Bantam Truck Mounted Shovel, 1:50 Scale ....................$60
Bobcat A300 Skid Steer Loader, 1:25 Scale ..................$40
Bobcat E35 Compact Excavator, 1:25 Scale ................$60
Bobcat M200 Gold Skid Steer Loader, 1:25 Scale ........$30
Bobcat M400 Gold 50th Anniversary Skid Steer Loader,
1:25 Scale..........................................................................$25
Bobcat M610 Golden 50th Anniversary Skid Steer
Loader ..............................................................................$25
Bobcat S175 Skid Steer Loader, 1:25 Scale ..................$45
Bobcat S205 Skid Steer Loader & Pick-Up Truck/Trailer
Set, 1:50 Scale ..................................................................$65
Bobcat 743 Skid Steer Loader, 1:25 Scale ....................$40
Bobcat 773 50th Anniversary Skid Steer Loader, 1:25
Scale..................................................................................$25
Case 580N Super N Backhoe/Loader, 1:50 Scale ........$50
Caterpillar AP655D Asphalt Paver, W/O Canopy, 1:50
Scale..................................................................................$85
Caterpillar Military D8R Track-Type Tractor, 1:50 Scale$65
Caterpillar D6K Track-Type Tractor................................$60
Caterpillar D8T Track-Type Tractor, 1:50 Scale ..........$110
Caterpillar D10T Track-Type Tractor, 1:50 Scale ........$105
Caterpillar D11R Track-Type Tractor, 1:50 Scale ..........$90
Caterpillar 226B3 Skid Steer Loader, 1:32 Scale ..........$50
Caterpillar 247B3 Multi-Terrain Track Loader, 1:32 Scale ..
..........................................................................................$50
Caterpillar 432E Backhoe/Loader, 1:50 Scale ..............$75
Caterpillar 906H Compact Loader, 1:50 Scale ..............$40
Caterpillar Military 924H Versalink Loader in Desert
Camouflage, 1:50 Scale ..................................................$45
Caterpillar 963D Track Loader, 1:50 Scale ....................$60
Caterpillar 977 Traxcavator, 1:50 Scale..........................$55
Doosan Moxy MT31 Articulated Truck ........................$115
Hamm GRW280 Compactor w/Cabin ............................$80
Hitachi EH700 Off-Highway Truck, 1:50 Scale ..............$40
International "S" Series Dump Truck,1:25 Scale ........$125
International TD-15 Dozer, 1:50 Scale ............................$65
International TD-20E Dozer, 1:64 Scale..........................$24
International TD-25 Dozer, 1:50 Scale ............................$70
John Deere 400D Articulated Truck, 1:50 Scale............$50
John Deere 624K Wheel Loader, 1:50 Scale..................$45
John Deere 850K Dozer ..................................................$60
John Deere 872 GP Grader, 1:50 Scale ..........................$60
Komatsu 475A Dozer, 1:50 Scale..................................$145
Komatsu D51 PX Dozer, 1:50 Scale................................$85
Komatsu D51 EX Dozer, 1:50 Scale................................$85
Komatsu D375 Dozer, 1:50 Scale..................................$110
Komatsu HD605 Off-Highway Truck, 1:50 Scale ..........$90
Komatsu HM250 Articulated Truck, 1:50 Scale ............$80
Komatsu PC14R Mini-Excavator, 1:32 Scale ................$50
Komatsu PC200 Excavator, 1:50 Scale ........................$105
Komatsu PC350 LC Excavator, 1:50 Scale ....................$90
Komatsu PC360LC-10 Excavator, 1:50 Scale ................$95
Komatsu PC400 LC Excavator, 1:50 Scale ....................$95
Komatsu PC2000-8 Front Shovel, 1:50 Scale..............$260
Komatsu SK1020 Skid Steer Loader, 1:25 Scale ..........$40
Komatsu SK1026 Skid Steer Loader, 1:25 Scale ..........$40
Komatsu WA500 Wheel Loader, 1:50 Scale ..................$95
Komatsu Mack Granite MP w/Lowboy Trailer, 1:50 Scale ..
........................................................................................$100
Link-Belt 800 X2 Excavator,1:50 Scale ........................$200
Link-Belt 80100 Rough Terrain Crane..........................$200
Mack Granite MP w/ Bottom Dump Trailer ....................$95
Mack R Model Mixer Truck, Patriotic Detailing, 1:34 Scale ..
..........................................................................................$95
Northwest 25-D Shovel, 1:50 Scale ................................$75
Peterbilt 367 Dump Truck w/ Beavertail Trailer, 1:50 Scale
........................................................................................$100
Terex AC 100/4 All Terrain Crane, 1:50 Scale ..............$190
Volvo EC460 L Excavator, 1:50 Scale ..........................$150
Volvo SD-122 Soil Compactor, 1:72 Scale ....................$25
All New in Box
CALL Toll Free
800-523-2200Ext. 197
Collections Wanted, I Buy Collections Shipping and Handling Included
Contact – Barry McKeon800-523-2200 Ext. 197 • 610-506-5961 Cell
Email – bmckeon@cegltd.com
CEG Scale Models470 Maryland Drive
Fort Washington, PA 19034Visit our Ebay Store – bmckeon collectibles – for a complete list with pictures.
Caterpillar 980G Wheel Loader on a Kenworth W900 and Trailking Trailer, 1:50 Scale...$150 Hamm 3307 Compact Roller, 1:34 Scale...$60
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 11
8231 John W. Carpenter Fwy
Dallas, TX 75247
See full inventory at: www.DarrJCB.com
(888) 616-5991Compactors - Walk/ Tow Behind2006 JCB Vibromax VM1500, 547 Hrs, 33”
Trench Roll ....................(FF000110) $7,500
2006 JCB Vibromax VM1500, 370 Hrs, 33”
Trench Roll ....................(90776245) $7,500
2007 JCB Vibromax VM1500, 560 Hrs, 33”
Trench Roll ....................(90808432) $7,500
2007 JCB Vibromax VM1500, 210 Hrs, 33”
Trench Roll ....................(90888203) $7,500
2005 JCB Vibromax VM1500, 341 Hrs, 33”
Trench Roll ....................(90948719) $7,500
2007 JCB Vibromax VM1500F85, 598 Hrs,
33” Roll ......................(100032784) $7,500
2008 JCB Vibromax VM1500F85, 10 Hrs,
33” Roll ......................(100032783) $7,500
Skid Steers2007 JCB 190, 1,167 Hrs ............................
....................................(AA002963) $18,500
Forklifts - Telescopic2008 JCB 520-50, 564 Hrs, 4,400 Pound,
16’6” Reach ................(91020886) $33,500
2006 JCB 524-40, 7,204 Hrs, 5,000 Pound,
17’4” Reach ..............(MSC02222) $17,000
Loader Backhoes2006 JCB 214, 2,391 Hrs, CN, 4wd, E-Stick,
w 24” Bucket ..............(CC000037) $33,000
2006 JCB 214, 2,917 Hrs, CN, 4wd, E-Stick,
w 24” Bucket ..............(BB000037) $33,000
2006 JCB 214, 2,279 Hrs, Cab, 4wd, E-Stick, w/ 24” Bucket....(FF000026) $33,0002007 JCB 3C, 1,355 Hrs, CN, 4wd, E-Stick,w 24” Bucket ..............(FF000211) $33,0002008 JCB 3C, 1,051 Hrs, CN, 4wd, E-Stick,w 24” Bucket ..............(90870582) $33,0002007 JCB 3CX14, 1,680 Hrs, CN, 4wd, Wet Kit, Std Stick ..............(90816565) $35,000
Wheel Loader2010 JCB 436E, 4,954 Hrs ..........................
................................(100033425) $125,000
Skip Loader2006 JCB 3C LL, 213 Hrs, Box Blade, 4wd,w LP Box Scraper ......(00107179) $25,0002006 JCB 3C LL, 1,082 Hrs, CN, 4wd, w 6’Box Blade ....................(FF000122) $25,000
Excavators2006 JCB JS260, 3,508 Hrs, 57,500 # Cap,Thumb, with Bucket ..(AA002602) $80,000
Excavators - Mini2008 JCB 8040Z, 463 Hours........................
....................................(91084658) $29,500
2005 JCB 8018X, 545 Hrs, w/ 12” Bucket ..
....................................(90924825) $15,000
2007 JCB 8018X, 690 Hrs ..........................
....................................(90886770) $15,000
2008 JCB 8018X, 291 Hrs, Canopy, 9”
Rubber Tracks ............(90993138) $17,000
2008 JCB 8025Z, 498 Hrs, Canopy, 10”
Rubber Tracks ............(90923647) $17,000
2006 JCB 8027Z, 784 Hrs, Canopy, 10”
Rubber Tracks ............(90954077) $15,000
2006 JCB 8027Z, 632 Hrs, Canopy, 10”
Rubber Tracks ............(90949801) $15,000
2006 JCB 8027Z, 377 Hrs............................
....................................(90954074) $17,000
2008 JCB 8035Z, 829 Hrs, Cab, Rubber
Tracks, 12” Bucket ......(90886772) $25,000
2006-2008 Trench Compactors w/RemoteControl, 10-598 Hrs..........................$7,500 Ea.
2005-2008 JCB 8018X, 291-690 Hours, RubberTracks, 12” Bucket ..................$15,000-$17,000
2006 JCB 214, 1,051 to 2,799 Hours, CN, 4wd,E-Stick, with 24” Bucket ........................$33,000
7 For
Sale3
For
Sale3
For
Sale
Page 12 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
ASCO Equipment Presents $130,515Check to Combat Marine OutdoorsOn Jan. 25, ASCO Equipment presented a check to
Combat Marine Outdoors (CMO) in the amount of $130,515to benefit CMO’s program for severely wounded marines,soldiers, airmen, sailors and navy corpsmen.The check resulted from a yearlong effort by local
employees in ASCO locations throughout Texas to benefitCMO in 2012. ASCO has a corporate and personal commitment to com-
munity and philanthropy, selecting deserving organizationseach year to benefit from the efforts of its employees andstaff, according to the company.“I’ve seen more scar from the battlefield healed and more
emotional scars healed for everybody,” said President ofCombat Marine Outdoors Rusty Hicks. “These guys’ sacri-fice to our country is not going to go unnoticed.”Individual fundraising efforts were determined by each
location. ASCO and the Wright family matched all moneyraised for the total amount. Command at the Wounded Warrior Battalion-San Antonio
Military Medical Center (SAMMC) and the WarriorTransition Battalion selected two deserving recipients for the
hunt: L.Cpl. Blake Watson, USMC (hometown Dallas,Texas) and Lt. Ryan Brunett, U.S. Army (hometown Troy,Mont.). Both were wounded in action in Afghanistan and are
active duty assigned for rehabilitation at SAMMC in SanAntonio. “It’s not that when you get injured your body’s different,
its that you don’t think you can do the things you love to do,”said Brunett. “So having everyone out here supporting usand giving us the opportunity to be outdoors and hunting anddoing the things we did in life before we were injured letsyou know pyschologically, emotionally and physically, ‘heyyou can still do everything you love to do.’”ASCO also has arranged for a personal phone call to the
service members by country music superstar, Trace Adkins.Trace has a long record of supporting the military andwounded warrior efforts. He also is spokesman for ASCO inTexas.“It’s better than any therapy you could receive from any
hospital,” said Watson.
About Combat Marine OutdoorsCombat Marine Outdoors started in 2005 after visiting
combat wounded Marines and Sailors from the 1st MarineDivision at Brooke Army Medical Center for severalmonths. The Marines, Sailors and service members thereneeded an opportunity to get away from the hospital, in anenvironment of friendship, camaraderie, and fellowship withfellow Marines in order to accelerate their recovery from thetraumatic injuries they sustained in combat. In many cases, these service members did not want to
leave the confines of the hospital, but it was (and is) crucialto begin to re-inculcate back into society. In every case, theMarines and other service members who participated in theoutings felt an enormous sense of accomplishment and anew sense of hope and belonging once the trip was complet-ed. For more information, visit http://www.combatmarine-
outdoors.org.For more information on ASCO, visit
http://www.ascoeq.com/.
On Jan. 25, ASCO Equipment presented a check to Combat Marine Outdoors (CMO) in the amount of $130,515 tobenefit CMO’s program for severely wounded marines, soldiers, airmen, sailors and navy corpsmen.
Command at the Wounded Warrior Battalion-SanAntonio Military Medical Center and the WarriorTransition Battalion selected two deserving recipientsfor the hunt: L.Cpl. Blake Watson (C), USMC (home-town Dallas, Texas) and Lt. Ryan Brunett, U.S. Army(hometown Troy, Mont.)
Road Machinery has recently welcomed two hires, RickDennis and Bill Schwenk. The company also has promotedMark Caldwell to regional general manager.Dennis has joined the company as regional sales manag-
er for Northern California. In his new position, Dennis isresponsible for increasing new and used equipment sales inhis territory, with six account managers reporting to him.“We welcome Rick to Road,” said Dan Roush, president
of Road Machinery. “He brings many years of experienceand a tremendous amount of technical and sales knowledgeto the company. We expect him to have a major impact inincreasing our market share.”Dennis has 35 years of experience in the heavy equipment
industry. He has extensive knowledge of the industry, due tothe wide range of departments he has worked with, includ-ing parts, accounting, inside and outside sales, and both salesand operations management.Schwenk has joined the company as regional sales man-
ager for Southern California. In his new position, Schwenkoversees equipment sales and rentals for the territory, withfive account managers reporting to him.“We expect Bill’s experience will give us a huge edge in
this very competitive market,” said Dan Roush, president ofRoad Machinery. “Bill has been extremely successful inheavy equipment sales over the past 30 years, and we expecthis impact to be significant.”Schwenk began his career in construction equipment as
an outside salesman for a dealership in Montana and waspromoted to regional sales manager there, where he built avery successful sales team, before moving to RoadMachinery. He will be responsible for building the compa-ny’s sales in the Southern California market.Caldwell has been promoted to regional general manager
of product support in California. In his new position,Caldwell oversees all parts and service operations for the 5locations in the state.“We expect Mark to have a major impact in growing our
parts and sales operations in California,” said Dan Roush,president at Road Machinery. “With over 30 years in theequipment business, he has the experience necessary tomake sure our customers’ needs are fully met. He will alsoplay an important role in deciding where additional branch-es should be located.”Caldwell began his career in the service department of an
equipment dealership and was promoted to service managerbefore moving to Road Machinery as general service man-ager. In the past few years, Caldwell’s responsibilities havebeen expanded consistently, including a promotion toregional general manager of Northern California, overseeingparts, service, and sales.Road Machinery LLC has been selling and servicing
heavy machinery since 1955. As the exclusive dealer forKomatsu in the Southwest, the company has fifteen loca-tions throughout the area, in Arizona, New Mexico, Texas,California and Mexico. For more information, call 800/989-7121 or visit www.roadmachinery.com.
Dennis, Schwenk..
Road MachineryWelcomes Two Hires,Promotes Caldwell
Powerscreen Texas will exhibit the XH250 ImpactCrusher at AGG1 in San Antonio, Texas from March 19to 21. “We are delighted that AGG1 is coming to San
Antonio and are excited to be taking part in the exhibi-tion. Our team of crushing and screening professionalsare looking forward to meeting new and existing cus-tomers to discuss how our equipment and features canbenefit their businesses,” said Sam McNabb, presidentof Powerscreen Texas.Tony Weir, Powerscreen technical sales and applica-
tions manager, will take part in the AGG1 Academy thisyear. Weir will present on improving equipment selec-tion and plant productivity using modern simulation andanalysis techniques Thursday, March 19. Powerscreen impactors are ideal for shaping applica-
tions including making chips, sand, concrete manufac-ture, and glass recycling. The Powerscreen XH250 Horizontal Shaft Impactor
is a highly compact tracked crusher designed to offerboth excellent reduction and high consistency of prod-uct yield. The XH250 is designed mainly for the recycling and
demolition markets and is an ideal contract machine dueto its compact design and mobility. Capable of process-ing a wide range of material at a high output, the plant isversatile, easy to operate and fuel efficient due to itsdirect drive system.Key benefits of the machine include a high consis-
tency of product shape alongside key features such ashydraulic overload protection and a throughput of up to275 tons per hour.For more information, visit
www.powerscreentx.com.
Powerscreen Texasto Exhibit at AGG1
The Powerscreen XH250 Horizontal ShaftImpactor is a highly compact tracked crusherdesigned to offer both excellent reduction andhigh consistency of product yield.
Pages 13-21
Crushing, Screening & Recycling SectionWirtgen’s 4200 SM WPI Surface MinerDetects Wear, Tear on Cutting ToolsWirtgen’s 4200 SM WPI surface miner with
integrated measurement system detects wear andtear on cutting tools. WPI stands for Wirtgen pick inspection — and
essentially consists of eight very quickly measur-ing sensors integrated in the cutting roller hous-ing. These sensors are used to measure the wear ofthe cutter. WPI can take measurements in less than one
minute and this can be carried out easily duringtruck changeover so that downtimes can be avoid-ed. The entire measurements are taken automati-cally at the press of a button, and the operator cansee the measurement results on a separate screen.Machine operators and service technicians arethus able to optimally plan any necessary serviceintervals, and the cutting tools are used to theirmaximum capacity.
4200 SM WPI: MaximumPerformance in Large-Scale
Opencast MiningThe new 4200 SM is a high-performance
machine for mine operators and customers inlarge-scale opencast mining whose goal is toachieve an annual mining capacity in soft rock of up to 12million tons with a single machine while wanting to makefull use of the benefits offered by Wirtgen’s selective miningtechnology that enables cutting, crushing and loading in asingle working pass. The surface miner is available to cus-tomers in two different designs: as a powerful mining expertfor hard rock, such as iron ore, bauxite or phosphate, or foruse in various types of soft rock including, for example, coalor lignite. The miner has a cutting width of 13.8 ft. (4.20 m)and is capable of working at a maximum cutting depth of32.7 in. (83 cm) in soft rock.The heavy-duty machine is equipped with a 16-cylinder
diesel engine from Cummins, making it the ideal candidatefor a wide range of applications as its power of 1,612 hp(1,194 kW) offers tremendous reserve capacity. Generouslydimensioned tanks offering capacities of 766 gal. (2,900 L)for diesel and 2,648 gal. (10,000 L) for water additionallyincrease the miner’s uptime.A two-stage conveyor system with 71 in. (180 cm) wide
primary and discharge conveyors and a discharge conveyorlength of 472 or 630 in. (1,200 or 1,600 cm) respectively,supports the miner’s cutting performance of up to 3,000 tons
per hour. The discharge conveyor’s large slewing angle of180 degrees, flexible height adjustment and variable beltspeed ensure smooth loading of large transport trucks evenin space-restricted conditions.
App for Service Teams Reduces Changeover Times
Another advantage of WPI comes from the simplifiedworkflow for the service teams responsible for changing thecutting tools. If a cutter needs to be changed, a separatemobile end device prepares the information stating whichcutter is to be changed. This function is accomplished by anapplication that shows part of the cutting roller and marks thecutter to be changed in color. In addition, when operating the entire surface miner fleet,
the information on the wear status of the cutting tools helpsto optimize the whole service and production process. Forexample, the use of service technicians and the provision ofspare parts is planned specifically based on the wear infor-mation of the individual machines.For more information, visit
www.wirtgen.com.
The use of WPI provides the machine operator with a quick andeasy overview of cutting tool wear — without causing anymachine downtime.
Page 14 • February 9, 2013 • www.constructionequipmentguide.com • Recycling Section • Construction Equipment Guide
Screen Machine IntroducesTracked CST Cone Crusher
Screen Machine Industries Inc.’s track-mounted CST cone crusher features a 51 in.(129.5 cm) quarry-duty cone crusher offering a high weight to power ratio. Thisplant features a vibratory shaker screen located between the feeder and the conecrusher. Pre-screening the fines will significantly reduce crusher wear costs andincrease overall plant production, according to the manufacturer.
This American-made machine utilizes Grade 80 steel construction for strengthand durability that will extend the machine’s overall life. Other features includeCaterpillar diesel power, heavy-duty tracked undercarriage and wireless remote-control movement and operation.
For more information, visit www.screenmachine.com.
Construction Equipment Guide • Recycling Section • www.constructionequipmentguide.com • February 9, 2013 • Page 15
The new Lokotrack LT120 jaw plant
Reliable crushing power
e roffomitpueromdnaw oyawenyllatotahtiwM steM,021TLLTkcartokoLehT
elia b Rw w he neT
wenllae,lbadnepedehTuoyelbailersitluserehT.gniknihtfo
senibmoc,tnalpwajtsetals’o
eliable crushing poT120 ack L LT120 jaotrokw L
rehsurcwaj021Cr ewopgnihsurcee cneirepxedilos
erweliable crushing potw planT120 ja
.mmetswwwmmineE-mail:
.ounear yn opsartotysaep acilppatsehguot
ou us 4 with its genere roffomitpueromdna
om.c.metso.com.nam@metsominerals
agnitcatnocyberomnraeL.trooperatotelpmisdnaeffeaS.snoita
, boosts preed opening 7 x 34 in. f feed openingwen-llae,lbadnepedehT.uoy
r otubirtsidosteMa
t and , compaceoperaty in the tivitoduc, boosts pr
, rehsurcwaj021C
CRISP INDUSTRIES, INC.323 Energy Way • Bridgeport, TX 76426
940-683-4070 • 800-315-0871 • Fax: 940-683-2181
www.crispindustries.com info@crispindustries.comSouth Texas 78155
830-625-6822Seguin, TX 78155
830-372-1110
WESTATEP.O. Box 50370 • Billings, MT 59105800-999-6676 • Fax: 406-373-6553
www.westate.com
COMPASS EQUIPMENT4688 Pacific Heights Rd. • Oroville, CA 95695
530-533-7284 • 530-533-8610 • Fax: 530-533-7657www.compassequip.com
WHEELER CRUSHING SYSTEMS
Salt Lake City, UT • Hurricane, UTOgden, UT • Vernal, UT
800-779-4450www.wheelercat.com/crushing
CONTRACTOR PREFERRED70% of all HydroSeeders® purchased by contractors today are
For Reliable Equipment to Get the Job Done, Call One of These Fine Dealers and Request
®
®
Perris, CA909-355-3600
Prescott, AZ928-778-5621
Gilbert, AZ480-545-2400
Tucson, AZ520-623-8681
Farmington, NM505-324-8601
Albuquerque, NM505-345-8383
El Paso, TX915-872-1001
www.roadmachinery.com
Dallas214-819-4100
Fort Worth817-626-2288
San Antonio210-648-4600
Longview903-758-5576
Austin512-388-2529
Houston713-937-3005
Mercedes956-565-0100
www.romco.comROMCO Equipment Co. hasacquired Conley Lott Nichols.
Both are Full Service Dealers for theEntire Finn Product Line, Including
HydroSeeders®
Straw Blowers
Bark Blowers
Page 16 • February 9, 2013 • www.constructionequipmentguide.com • Recycling Section • Construction Equipment Guide
Survey Indicates Construction CompaniesWill Continue to Invest in IT Infrastructure“While the outlook for the construction industry appears
to be heading in the right direction for 2013, many firms arestill grappling with significant economic headwinds,” saidStephen E. Sandherr, the association’s chief executive offi-cer. “With luck and a lot of work, the hard-hit constructionindustry should be larger, healthier, more technologicallysavvy and more profitable by the end of 2013 than it istoday.”Sandherr noted that significantly more firms are planning
to add staff this year compared to the number of firmsexpecting to make layoffs. He said that 31 percent of firmsplan to add staff this year, while only 9 percent plan to makelayoffs this year. The scope of those staff additions are like-ly to be modest, however, with 79 percent of firms reportingthey plan to hire 15 or fewer people in 2013 and only 13 per-cent planning to hire more than 25 new workers this year.Among the 30 states with large enough survey sample
sizes, 56 percent of firms in Maryland plan to hire new staffthis year, more than in any other state. Only 14 percent offirms in South Carolina plan to add staff this year, the leastamount in any state. Meanwhile, 37 percent of firms inMichigan plan layoffs for this year, the highest percentage ofany state. No firms working in Maryland reported plans tomake layoffs this year. Contractors appear increasingly optimistic that demand
for certain private sector projects will expand this year,Sandherr noted. Firms are most optimistic about the outlookfor hospital and higher education construction, he said, not-ing that 36 percent of firms predict the amount of moneyspent on those projects will grow in 2013 while 39 percentof firms expect the market will remain stable compared tolast year. Contractors also were optimistic about the marketsfor power construction, but had lower expectations for man-ufacturing; private office and retail, warehouse and lodgingconstruction.Meanwhile, contractors expect demand for many types of
public construction will decline in 2013. For example, 40percent of contractors report they expect demand for publicbuildings to shrink in 2013 while only 18 percent expect thatmarket to grow. Another 37 percent of contractors reportthey expect demand for K-12 school construction to shrinkwhile only 20 percent expect it to increase. And 35 percentof contractors expect the market for manufacturing facilitiesto shrink this year, while only 23 percent predict it willexpand.A significant — but smaller than last year — number of
contractors report that customers’ projects have been delayedor cancelled because of tight credit conditions. Forty percentof responding firms report that tighter lending conditionshave forced their customers to delay or cancel constructionprojects. Only 3 percent of firms reported having an easiertime getting credit while 41 percent report no change in cred-it conditions.“Unfortunately, there are almost as many causes for con-
cern as there are signs of optimism,” said Ken Simonson, theassociation’s chief economist. “Demand for public buildingsis set to decline, manufacturing work appears to be slacken-ing, materials prices and health care costs continue to riseand many firms are reluctant to make major investments innew equipment.”
Simonson noted that overall demand for new constructionequipment is likely to remain modest in 2013. Sixty-fourpercent of firms plan to purchase new equipment this year,down from 70 percent last year, while 77 percent of firmsplan to lease this year compared to 78 percent in 2012.Contractors are increasingly relying on leasing equipment toavoid having to pay for idle equipment during lags in con-struction activity, the economist noted. Even as they shifttoward more leasing, firms’ appetite for new equipmentremains modest, with two-thirds of the firms planning to buyand 73 percent planning to lease $250,000 or less in equip-ment this year.��Contractors also report being squeezed byrising costs for health insurance and construction materials.Seventy-five percent of firms reported paying more forhealth care coverage in 2012 and 77 percent expect to payeven more in 2013. Meanwhile, 88 percent of firms reportedpaying more for construction materials last year while 90percent expect to pay more for their supplies this year.However, contractors are increasingly optimistic about theirability to raise bid levels. Twenty-eight percent of firmsexpect to increase the amount they charge for constructionthis year, nearly double the 15 percent of firms that increasedprices in 2012.An increasing number of construction firms — 38 percent
in 2012 compared to 35 percent in 2011 — report usingBuilding Information Modeling services, also known asBIM, association officials noted. And 43 percent report theyexpect the use of BIM to increase in 2013. In addition, morefirms report working on public private partnerships, whichleverage private-sector dollars to finance public projects.Thirty-seven percent of firms report being involved in thesekinds of projects in 2012 and 97 percent expect demand forthese kinds of privately financed projects to increase orremain stable in 2013.“The survey indicates that construction companies will
continue to make investments in their IT infrastructure,specifically in areas such as enterprise content management,mobile field applications and solutions that support self-serv-ice functions,” said Roger D. Kirk, CEO, ComputerGuidance Corporation.Kirk noted that 60 percent of firms report they plan to
invest in their information technology departments in 2013.He added that 73 percent of those firms report they expect toinvest over $10,000 in new information technology this year.However, a relatively small percentage of firms — 11 per-cent — report they plan to purchase new financial and jobcost software in 2013, Kirk added. Similarly, only 9 percentof firms plan to lease or finance the purchase of new finan-cial and job cost software in 2013.The outlook, which the association co-sponsored with
Computer Guidance, was based on survey results from morethan 1,300 construction firms from 49 states, the District ofColumbia and Puerto Rico. Contractors from every segmentof the industry answered more than 30 questions about theirhiring, equipment purchasing and business plans.Economists and specialists from the association andComputer Guidance analyzed those comments to craft theoutlook.
OUTLOOK from page 1
www.petersoncat.comNorthern California
888-738-3776Oregon/Southern Washington
800-452-7676
Chico, CARedding, CAFortuna, CAWillows, CAWillits, CA
Santa Rosa, CASan Martin, CASan Leandro, CAEugene, OR
North Bend, ORKlamath Falls, ORRedmond, ORMedford, ORAlbany, ORPortland, ORSalem, OR
The Dalles, ORLongview, WA
www.wagnerequipment.comAlbuquerque, NM
505-345-8411Aurora, CO
303-739-3000Burlington, CO719-346-7880
Colorado Springs, CO719-635-1669Durango, CO
970-259-2001El Paso, TX
915-821-7651Farmington, NM505-327-5331
Grand Junction, CO970-242-2834Hayden, CO
970-276-3781Hobbs, NM
575-393-2148Pueblo, CO
719-544-4433Windsor, CO
970-278-1750
www.warrencat.com866-292-7736P.O. Box 60662
Midland, TX 79711432-571-4200Abilene, TX
325-692-1600Amarillo, TX
806-335-1511Lubbock, TX
806-745-4495Odessa, TX
432-332-1681San Angelo, TX325-655-1100Wichita Falls, TX940-767-4384
Oklahoma City, OK405-947-6771Tulsa, OK
918-627-4500
www.louisianacat.com3799 W. Airline HwyReserve, LA 70084
985-536-0946Fax: 985-536-0950
Alexandria318-443-2577Bossier City
318-746-2341Hammond
985-340-2820Lafayette
337-837-2476Lake Charles
337-439-3601Monroe
318-323-1345Prairieville
225-673-3480Reserve
985-536-1211
www.ncmachinery.com800-562-4735
In Alaska800-478-7000Seattle, WA
425-251-5800Chehalis, WA360-748-8845
Fife, WA253-896-0878Monroe, WA
360-805-6000Mt. Vernon, WA360-424-4292Wenatchee, WA509-886-5561Yakima, WA
509-248-2371Anchorage, AK907-786-7500
Dutch Harbor, AK907-581-1367Fairbanks, AK907-452-7251Juneau, AK
907-789-0181Prudhoe Bay, AK907-659-6900Wasilla, AK
907-352-3400
800-332-7095Billings, MT
406-656-0202Billings-Sgt, MT406-245-4426Bozeman, MT406-585-5800Great Falls, MT406-761-7900Helena, MT
406-442-2990Williston, ND701-572-8377Worland, WY307-347-4747
Construction Equipment Guide • Recycling Section • www.constructionequipmentguide.com • February 9, 2013 • Page 17
Innovative American made no compromise
Join the revolution715-395-6060 www.exodusmachinesinc.com superior, wisconsin
BIG. Bad. fast. strong.
AVAILABLE.
The MX457130K lbs. 300 hp. 13,430lb@60’. 63’ 5” reach.
www.holtcat.com800-275-4658
Austin, TX • Bridgeport, TXCorpus Christi, TX • Fort Worth, TX
Irving, TX • Laredo, TXLewisville, TX • Longview, TX
North Dallas, TX • Pflugerville, TXSan Antionio, TX • Sonora, TX
Texarkana, TX • Tyler, TXVictoria, TX • Waco, TX
Weslaco, TX
www.johnson-machinery.comRiverside, CA951-686-4560
Fontana, CA909-574-6601
Indio, CA760-342-1597Murrieta, CA
951-696-1063Hesperia, CA
760-947-0967
www.mustangcat.comHouston, TX
713-460-2000Beaumont, TX409-892-8412
Bryan, TX979-775-7368
Bryan, TX979-775-0639
Channelview, TX281-452-7368
Conroe, TX936-756-1110El Campo, TX979-543-3389Freeport, TX
979-233-7368Houston, TX
713-462-9993Houston, TX
713-228-7368LaMarque, TX409-935-7000
Lufkin, TX936-639-5551
Lufkin, TX936-632-6775Nederland, TX409-722-7368
www.hawthornecat.comSan Diego, CA 92127
800-437-4228Waipahu, HI
800-344-8603
Lakeside, CA • San Marcos, CAHilo, HI • Lihue, HI
Kailua Kona, HI • Kahului, HIWaipahu, HI
Page 18 • February 9, 2013 • www.constructionequipmentguide.com • Recycling Section • Construction Equipment Guide
Call David Spainhour in Dallas,TX214-688-0444 • Fax 214-630-5419
Email:dspainhour@midcosling.com
MIDCODemolition
Tool CompanyPerforms a
Complete Teardown& Complete Rebuild
Including:1 - Remove the head.
2 - Pull the cylinder.3 - Hot pressure wash the entire unit.
4 - Polish piston & check tolerances. 5 - Rebuild & charge accumulator.
6 - Install all new seals. 7 - Repaint to spec.
8 - Install new chisel & bushing.9 - All hammers include new hoses, seals, chisel or moil points, paint, OEM decals
and final hammer testing.
Midco Offers the Finest in NewHydraulic Hammer and the Highest
Quality in Rebuilds!
SALES • SERVICE • PARTS
Some HammersAre Just Too
For Their Ads!Big
OEM REPAIR FACILITY - DALLAS, TX
MIDCO Demolition Tool Company...
Your “One-stop Shop” for New, Used and RebuiltHydraulic Hammers Plus Over 1,300 Hammer
Tools and Parts for Sale!
www.superior-ind.com
KING OF THE HILL
At Superior, we’re constantly searching for new ways to use our knowledge of bulk material handling systems to solve challenges and improve production. We’re driven by curiosity, loaded with determi-nation and energized by progress. How can we help you?
McCOURT & SONSEQUIPMENT, INC.5141 Hwy 71 West
LaGrange, TX 78945979-242-5298888-838-9252
www.portablescreen.com
COMPASS EQUIPMENT INC.
4688 Pacific Heights RoadOroville, CA 95695530-533-7284530-533-8610
www.compassequip.com
Official dealer partnerin Texas, Louisianaand Mississippi.
Official dealer partner in Northern California.
POWER EQUIPMENT CO.500 E. 62nd Ave.Denver, CO 80216800-883-9284
www.power-equip.comLocations:Denver, CO
Colorado Springs, COGrand Junction, CO
Casper, WYAlbuquerque, NM
Construction Equipment Guide • Recycling Section • www.constructionequipmentguide.com • February 9, 2013 • Page 19
Picking Station with Screen-It
Separate-It RWS 2000 Rock/Wood SeparatorRock-It Static Grizzly
6x16 2 Deck Screen-It
102x152 Track Mounted Impact Plant
POWERFULrack machines provide thGlobal T Track machines provide the
heaviest & most productive componentsto help you conquer your toughest jobs.
TL
The
LGT
POWERFULrack machines provide the
heaviest & most productive componentsto help you conquer your toughest jobs.
TLINLINET
to help you conquer your toughest jobs.
ABLEPORTTABLErack series machines are sGlobal T Track series machines are sleeker
and more compact, making them easy tot to and around any job site.transpor
ABLPROFITTABLErack systems are desAll Global T Track systems are designed
to be 100% compatible with each otherfectCombine them to build the per
to help you conquer your toughest jobs.
rack series machines are sleekerand more compact, making them easy to
t to and around any job site.
ABLErack systems are designed
. ch other r.fect
fectCombine them to build the persystem for your operation.
fect
racks provide both job site mobility asTwell as the foundation required to isolateplant vibration.
r
racks provide both job site mobility aswell as the foundation required to isolate
n more: wwwLog on, lear
r
.kpijci.com. more: www w.kpijci.com.
GT145S Screen
390 N. 2000Lindon, UT 84042
801-796-6126 • 801-796-6128
Boulder City, Nevada702-293-7504
Fax: 702-293-0529
San Bernardino, CA908-887-9800
Fax: 909-887-9888
Goodfellow Crusherswww.goodfellowcrushers.com
Introducing the new Lokotrack ST2.4 mobile screen
Quality delivers precision
QnI
elia , the ST2.4 is built with high-ableand rating pos sition in just
e een that goe mobile scrokotrack ST2.4 is a vkw Lhe neT
d eviledytilauQn artokoLweehtgnicudortn
qual, the ST2.4 is built with high-obust . Repsw simple ste a f fe
-o opert tom transporeen that goes frt , compacersatileotrack ST2.4 is a v
noisicerpsrneercselibom4.2TSkca
E-mail: m .nam@metso minerals
etso or tibut distrMlenges e bn morear. Lsneed t espond to r t
dra viding the exibilito, prulicallyyhe an nd easy with saffe and easy with a scr
and e� eening media changes arcr. Sy �ciency com or mponents f for morit
elia , the ST2.4 is built with high-ableand r
.com.nam@metso
.yodaour local ting yy contace b
-eening chalent screro di erespond tou y yviding the exibilit
x that raises een boe and easy with a scre eening media changes ar
e uptime tivoduce pror mor-qual, the ST2.4 is built with high-
.met om.ctsowww
CRISP INDUSTRIES, INC.323 Energy Way • Bridgeport, TX 76426
940-683-4070 • 800-315-0871 • Fax: 940-683-2181
South Texas 78155830-625-2181
South Texas 78155830-625-6822
COMPASS EQUIPMENT4688 Pacific Heights Rd. • Oroville, CA 95695
530-533-7284 • 530-533-8610 • Fax: 530-533-7657
www.compassequip.com
Page 20 • February 9, 2013 • www.constructionequipmentguide.com • Recycling Section • Construction Equipment Guide
Construction Equipment Guide • Recycling Section • www.constructionequipmentguide.com • February 9, 2013 • Page 21
SENNEBOGEN green line material handling machines make your competitors “green with envy”SENNEBOGEN green line material handling machines make your competitors “green with envy”
High Productivity – Low Operating Costs
Titan Machinerywww.titanmachinery.com
Denver, CO303-286-7000
Fargo, ND701-237-3333
Omaha, NE402-733-3700
Sioux Falls, SD605-336-3434
Modern Machinerywww.modernmachinery.com
Spokane, WA800-541-0754
Kent, WA800-669-2425
Rochester, WA800-304-4421
Portland, OR800-950-7779
Eugene, OR800-826-9811
Boise, ID 800-221-5211
Pocatello, ID 800-829-4450
Missoula, MT800-332-1617
Kalispell, MT800-434-4190
Billings, MT 800-735-2589
Bane Machinery Inc.www.banemachinery.com
Dallas, TX214/352-2468
Fort Worth, TX817/847-5894
Waukesha-Pearce Industries, Inc.
Corporate Office: 12320 So. MainHouston, TX 77035
713/723-1050 • Fax: 713/551-0798www.wpi.com
Tomball, TX281/351-9016
Kilgore, TX903/984-2011
Port Arthur, TX409/721-5305
Corpus Christi, TX361/884-8275
Edinburg, TX956/386-0107
San Antonio, TX210/648-4444
Pflugerville, TX512/251-0013
Buffalo, TX903/322-7150
Page 22 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 23
Built from a lineage of market leaders for over 60+ years
ARIZONAEARHART EQUIPMENT
www.earhartequipment.comTucson
520-889-6396
OKLAHOMAOCT EQUIPMENT
www.octequipment.comClinton
580-323-3422Oklahoma City405-789-6812
Tulsa918-437-5085
NEW MEXICOWAGNER EQUIPMENT CO.www.wagnerequipment.com
Flora Vista505-334-5522 (Rental)
La Cruces575-647-9700Albuquerque
505-938-2000 (Rental)505-345-8411
Hobbs575-393-2148 (Rental)
575-393-3665Clovis
505-235-3294 (Rental)Farmington
505-327-5331
NEVADAAPCO EQUIPMENT
www.apcoequipment.comNorth Las Vegas702-871-7474
HAWAIIHAWTHORNE CAT
www.pacific.hawthornecat.comHilo
808-961-3437Kauai
808-245-4058Kona
808-329-4521Oahu
808-677-9111Oahu/Mapunapuna
808-834-8797 (Rental)Maui
808-877-6538
COLORADOWAGNER EQUIPMENT CO.www.wagnerequipment.com
Aurora303-739-3000
Denver303-433-2727 (Rental)
Carbondale970-963-7368 (Rental)
Commerce City303-286-2300 (Rental)
Colorado Springs719-390-7316 (Rental)
719-635-1669Granby
970-328-2080 (Rental)Gypsum
970-328-2080 (Rental)Hayden
970-276-3781
Silverthorne970-262-3788 (Rental)
Fort Collins970-493-5005 (Rental)
Grand Junction970-245-6546 (Rental)
970-242-2834Pueblo
719-544-0088 (Rental)719-544-4433
Steamboat Springs970-871-1990 (Rental)
Windsor970-278-1750 (Rental)
Burlington719-346-7880 (Rental)
(719) 346-5132Durango
970-259-2001 (Rental)970-259-2001
Windsor970-278-1750
TEXASANDERSON MACHINERY CO.www.andersonmachinery
texas.comCorpus Christi361-289-6043
Manor512-272-8133
Pharr956-781-5995San Antonio210-661-2366
Victoria361-575-8111
HOLT CATwww.holtcat.com
Dallas214-342-6700Ft. Worth
817-847-8880Irving
214-342-6700Waco
254-662-7377
GEORGE P. BANE, INC.www.banemachinery.com
Tyler903-597-6641
YELLOWHOUSE MACHINERYCO.
www.yellowhouse.usAbilene
800-592-4468Amarillo
800-658-9868Lubbock
800-658-9878Odessa
800-658-9888San Angelo
800-658-9130Wichita Falls877-658-9877
MUSTANG CATwww.mustangcat.com
Houston 713-460-2000Beaumont
409-892-8412
Bryan979-775-7368
Bryan979-775-0639Channelview281-452-7368
Conroe936-756-1110El Campo
979-543-3389Freeport
979-233-7368Houston
713-462-9993Houston
713-228-7368LaMarque
409-935-7000Lufkin
936-639-5551Lufkin
936-632-6775Nederland
409-722-7368
WAGNER EQUIPMENT CO.www.wagnerequipment.com
El Paso915-493-5005 (Rental)
915-821-7651
CALIFORNIAHAWTHORNE CAT
www.hawthornecat.comSan Diego
858-674-7000Lakeside
619-561-8700 (Rental)San Marcos
760-740-2900 (Rentals)
QUINN CATwww.quinncompany.com10006 Rose Hills Road
City of Industry, CA 90601888-842-2155
Fax: 562-692-1843BakersfieldCorcoranFirebaugh
Foothill RanchFresno
LancasterLos AngelesOxnardSalinas
Santa MariaSylmar
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 25Page 24 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 25Page 24 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
Page 26 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
JCB Machines to Help Unearth Buried Wartime SpitfiresTwo excavators and a backhoe made by
Staffordshire-based JCB are about toembark on a mission to help recover Spitfirewarplanes designed by one of the county’smost famous sons and believed to be buriedin Burma.The unassembled planes are thought to
have been hidden in the ground by Americanengineers across three sites as World War IIdrew to a close.Now a bid to excavate for crates thought
to contain more than 30 of the Spitfires isabout to get under way at RangoonInternational Airport, and JCB is providing a22 ton (20 t) JS200 tracked excavator, a 24ton (22 t) JS220 tracked excavator and a3CX Eco backhoe loader to complete thejob.The company also is dispatching the team
leader of the world famous JCB DancingDigger display team, JCB demonstratorOliver Keates of Cheadle, Staffordshire, tooperate the machines and offer expert adviceon the digging operation.
JCB was founded by renowned engineerJoseph Cyril Bamford in a lock-up garage inUttoxeter, Staffordshire, in October 1945and under the leadership of his son,Chairman Sir Anthony Bamford, it hasgrown into the world’s third largest manu-facturer of construction equipment.It is another great Staffordshire engineer,
Reginald Mitchell, who is famous fordesigning the Spitfire. He was born in 1895in Kidsgrove, Staffordshire, and educated atHanley High School, Stoke-on-Trent.Bamford said, “Reginald Mitchell put
Staffordshire on the map in the 1930s withthe design of the Spitfire so it’s very fittingthat JCB, a modern day innovator and engi-neering company based in the county, shouldbe providing the excavators to dig up theplanes.”Oliver Keates, who has worked for JCB
for 14 years, said, “I’m excited at theprospect of being involved in this project.
It’s going to be thrilling to be atthe controls of JCB machinesattempting to unearth a Spitfire.”Businessman Julian Mitchell,
of Newcastle, Staffordshire, whois Reginald’s great-nephew said:“I’m delighted that JCB isinvolved in helping recover theSpitfires. Staffordshire is a greatmanufacturing county and I’msure my great-uncle would havebeen pleased that a modern-dayBritish engineering success storywas playing such an importantrole in this project.”The dig is getting under way after a 17
year search for the Spitfires led by aviationenthusiast David Cundall. Award-winningon-line games developer Wargaming isfunding the efforts to recover the buriedSpitfires.The JCB 3CX backhoe loader is the
world’s most versatile piece of constructionequipment and is one of the biggest sellingmachines due to its ability to load, road andexcavate. It weighs in at 17,000 lbs. (7,711kg) has a top speed of 25 mph and a bucketcapacity of 1.4 cu yd. (1 cu m). JCB hasmade more than half a million backhoessince 1953. The JS200 tracked excavator
being used in the dig is powered by a 172 hp(128 kW) engine and can dig to a depth of21.8 ft. (6.6 m).JCB is supplying the machines through its
dealer in Burma, RMA Services Co Ltd.Based in purpose-built facilities in Yangon,the company also is providing logistical andservice support.
Aviation enthusiast David Cundall, pictured with a JCBmachine, which had just arrived on site in Burma.
JCB’s Oliver Keates prepares to leave the snow behind to head for Burma where he will beleading the excavations for more than 30 unassembled WWII Spitfires thought to be buriedat Rangoon International Airport.
“I’m excited at the prospect of being involved inthis project. It’s going to be thrilling to be at thecontrols of JCB machines attempting to uneartha Spitfire.”
Oliver KeatesJCB
SECT IONAttachments
Safety, Efficiency Depend on Proper Drill OperationBy Randy StevensSPECIAL TO CEG
Pneumatic concrete dowel drills have onepurpose — to drill holes. While their intend-ed use is easy to recognize, operation of thisequipment isn’t quite so simple. In fact, it’s abit of a science. That’s not to say they’re dif-ficult to operate. But there are certain bestpractices and processes to keep in mind forproper drill operation, whether it’s an on-grade, slab-rider or equipment-mountedmodel. Operators who adopt these guide-lines and implement them on every job arerewarded with better performance from themachine and fewer hassles overall.
First Things FirstBefore even getting the drill close to a
concrete slab, a few simple preparations areneeded. A pneumatic dowel drill virtuallycomes out of a box, poised to go to work; allit takes to ready it for a job is air, a drill bitand a couple simple steps. Specific instruc-tions vary with each make and model, so fol-low the exact recommendations in theowner’s manual. Generally speaking, thebasic items begin with attaching and secur-ing the air hose from the compressor to thedrill. Next, install the drill bits. When doingso, it’s necessary to have the correct bit guidebushing to match the bit. This centralizes thebit and keeps it from moving around toomuch. The bit also must be the proper chucksize for the drill. Adjust the drill spacing andheight, level the drill and set the drillingdepth. Finally, be sure to start with the proper
lubricating oil in the oiler. Most manufactur-ers recommend rock drill oil, as it’s heavyand thick enough to run this large of a pieceof equipment. Some operators may try to usepneumatic tool oil or even automatic trans-mission fluid. These types of lubricants aremuch lighter and almost a watery consisten-cy. While ideal for smaller tools, like impactwrenches, these lubricants often won’t standup to the demands of a large dowel drill. After these basic preparations, a dowel
drill is almost ready to begin its job. Prior to
any actual drilling, every operator shouldknow the basics of proper use to ensure asmooth process and end result. Following afew guidelines will result in projects that arecompleted efficiently, safely and withoutequipment failure whether they’re newpours or full-depth repairs.
Under PressureMost highway paving, airport repair and
smaller residential roadwork projects haveone thing in common: deadlines. Everypiece of equipment must perform at its max-imum efficiency level so the company cankeep up with strict timelines and avoidpenalties. Setting a drill to the proper feed pressure
is the first step to optimal drilling. There is acommon — and incorrect — belief thatincreasing the feed pressure will increase thedrilling speed and efficiency, but that’s sim-ply not true. Finding the proper feed pressureis the best way to ensure maximum efficien-cy, and also to prevent unnecessary damageto drill bits and the drill itself. This greatlyminimizes downtime for replacements, aswell as costs for new bits or more significantrepairs to the drill.Whether using an on-grade, slab-rider or
equipment-mounted drill, each has virtuallythe same process for setting and adjustingfeed pressure. Feed pressure varies based onthe drill and application, so there’s not a spe-cific setting that’s going to work for all sce-narios. The best approach is to set a logicalstarting point and then adjust as neededbased on the results. Most manufacturersrecommend a starting point between 18 to25 psi for horizontal drilling applications.From there, the operator simply needs towatch the machine’s performance and adjustif necessary. For example, if the drill is “bouncing” on
the concrete’s surface rather than drillinginto it, the pressure is too weak and the oper-ator needs to increase it. Conversely, if thepressure is too great, the bit’s rotation willslow down or even stop. In this case, adjustthe pressure down until normal rotationresumes. Most drills have an easily
adjustable regulator knob that simply needsto be turned one way or the other to adjustpressure up or down. On job sites with multi-gang drills, it’s
recommended to go through this process onedrill at a time. After proper adjustments havebeen made to each individual drill, they canbe run simultaneously. However, afterthey’re all turned on simultaneously for thefirst time, it’s also the first time they’re allbeing run off the same air compressor, soslight adjustment may be needed to be surethey’re all still receiving adequate pressure. Some on-grade and slab-rider drills can be
converted to vertical drilling and there alsoare specific models designed just for thisapplication. In the case of vertical drilling,the same process can be used with a minoradjustment. Feed pressure should be reducedanywhere from about 5 to 9 psi from thestart, then adjusted up only. This is a com-mon safety precaution because, if the pres-sure is set too high, the drill can tip over. Keep in mind the two factors that affect
ideal feed pressure before the bit ever meetsthe concrete: drill bit size and the hardness ofconcrete. It’s important to remember thiswhen the drill is moved from one job site tothe next. What worked for one airport laneaddition may not be ideal for another one ina different setting. Again, it all goes back tomonitoring performance and adjusting pres-sure as needed.Another key to achieving optimal opera-
tion and minimal stress on the drill is a rela-tively simple concept: every drilling applica-tion should be approached in a series ofstrategic steps.
Keeping Things in OrderImagine a homebuilding project. The only
way to succeed is to follow a proper series ofsteps. Pour the foundation, put the framing inplace, put up the drywall and, finally, installthe fixtures. Mess with the sequence and theproject won’t make it very far. Similarly,there’s a proper sequence for before and afterdrilling. Following it prevents damage to thedrill and components and makes a successfulproject more likely.
Spawling is a great example of an issueone can avoid with proper pre- and post-drilling procedures. This common problemresults in excess concrete chipping awayfrom the hole area. While some spawling isnatural in a concrete drilling application, fol-lowing the proper sequence will keep it to aminimum and is the best way to avoid anyissues with inspectors.In addition, both the pre- and post-hole
techniques help to prevent dry-firing, a situ-ation in which the drill is in operation butthere’s no pressure on the bit. Dry-firingadds unnecessary stress to the drill and candamage its trunnion bolts. Every bit has alatch, which is held in place by a trunnionbolt. The stress dry-firing places on the drillcan eventually cause the bolt to break. Withproper operation, a trunnion bolt can last theentire lifetime of the drill. At around $80apiece, it isn’t a part most operators want toreplace frequently, if ever.Whether it’s for a single hole or set of
holes, the first step is to properly position thedrill along the designated area of a slabwhere holes are to be drilled. Next, feed thedrill. Place it against the concrete and movethe feed control valve to the “In” position.When the bits make initial contact with theconcrete, place the main power switch in the“On” position and the drill will begin oper-ating.After the drill has reached its desired
depth, it’s crucial to turn it off immediatelyto prevent dry-firing. Then, there’s a properremoval sequence to follow as well. Prior totaking the drill out of the hole, stop the drillby moving the main power switch to the“Off” position. Do the same for the feed con-trol valve and that will cause the drill toretract. Occasionally, the drill bit canbecome stuck in the hole and make it diffi-cult or impossible to retract the drill. If that’sthe case, simply turn on the power valve.This will allow the bit to rotate enough thatit should easily begin to retract. At that point,shut off the valve. If a drill has an auto alignswitch, it’s wise to place it in the “Up” posi-
see PNEUMATIC page 28
Pages 27-29
Page 28 • February 9, 2013 • www.constructionequipmentguide.com • Attachments Section • Construction Equipment Guide
Negligent Operation CanCreate Safety Hazardstion before fully pulling it away to move tothe next location. This slightly raises the drillaway from the concrete. When the drill hasbeen moved and placed in its next location,move the auto align switch to the “Down”position and repeat the sequence.Some operators neglect to turn off the drill
before removing it from the hole and otherseven leave it running when moving to a newlocation. While it’s tempting to skip theproper steps in an effort to save time, it’s notsafe and will end up causing moreheadaches.Safety is one area on the job site where
there’s no room for compromise. As withany major piece of machinery, dowel drillshave their own set of safety guidelines thateveryone on site needs to follow.
Safety NotesDowel drilling isn’t a dangerous process.
However, as with any piece of equipment,negligent operation or a complete disregardfor safe practices can create serious hazards.Just like ignoring proper operationalsequences, ignoring safe operation practicesmay put more than just the operator in jeop-ardy; it also can lead to a damaged drill orcomponent.Begin with the basics, proper work attire.
Workers should wear earplugs to preventdamage from drill and air compressor noise.Debris flies during drilling, so the operatorand other workers on the site must wear safe-ty glasses and hardhats, as well. Concrete dust is often emitted during the
process too, so dust masks are a must-havefor all on site workers. But concrete dust canpose other risks too. If large amounts areemitted, the dust can cloud a site and createa low-visibility environment for workers or,worse, for nearby live traffic. To help mini-mize dust emissions, many companies offerpneumatic drills with dust suppression kitsor dust collection systems. Dust suppressionkits include a spray nozzle, which attaches toeach drill system and sprays water on the bitas it’s drilling. A dust collection system runson the same compressor as the drill and vac-uums dust as it’s emitted. The system’s dustcollection head typically mounts to the endof the bit guide, where the bit penetrates theconcrete. The vacuum draws out duststraight from the hole and into the collectionbag. Both systems keep airborne dust andrelated hazards to a minimum. A few areas of the drill pose specific dan-
ger to operators. Every drill has pinch points
where fingers, hands or limbs can becomecaught. A primary example is the carriageassembly. Keep clear of the carriage assem-bly to avoid being caught between the car-riage and frame. When moving a drill, besure the carriage lock is set to prevent theassembly from sliding onto fingers andhands. Furthermore, improperly moving a drill
can cause operator strain or a serious acci-dent. When moving a drill on the ground,operators should use the unit’s designatedhandles. If the drill is lifted improperly, itcould cause a strained back or other muscleand joint problems. If a drill needs to bemoved a greater distance, a lifting devicemight be necessary. In this case, use a prop-erly weight-rated strap or chain and attach itto the drill’s lifting bale. Be sure the carriagelock is in place. Compressed air is required to run a pneu-
matic drill and the great pressure can posesafety issues. The operator should monitorthe air compressor’s gauge to be sure pres-sure doesn’t inch up too high. If the pressureis too high, it can damage the drill. This mayvoid the warranty altogether, but even moredetrimental is the lost productivity as a resultof downtime. Additionally, before moving,disconnecting the air hose or any parts or dis-assembling the unit, the operator must firstshut off the air supply and bleed off any airin the system. Taking just a few minutes todo so will help eliminate potential injuries. One final note to ensure efficient opera-
tion and long drill life is perhaps the simplestof all — keep the drills clean. At the end ofeach workday, use the air compressor toblow off all dust and debris from the drills.While it doesn’t seem like much, it can payoff greatly. Doing so prevents cloggingissues and excessive dust build-up. In theevent of rain, any dust accumulated willquickly harden to concrete when it dries. Ifchoosing to pressure wash the drills post-operation, be sure to dry thoroughly to pre-vent any potential concrete accumulation.No matter the project size, timeline or
logistics, the need for correct drill operationis one component of a job that’s always aconstant. Proper operation isn’t difficult orcomplicated, it simply boils down to a fewbest practices. The small investment of timeand thought pays back large dividends in jobsite safety and productivity. And, ultimately,the result is a piece of equipment that costsless to own and offers more years of reliableservice.
PNEUMATIC from page 27
The “It’s Only Another Beer” Black and Tan
8 oz. pilsner lager8 oz. stout lager1 frosty mug1 icy road1 pick-up truck1 10-hour day1 tired workerA few rounds with the guys
Mix ingredients.Add 1 totalled vehicle.
Never underestimate ‘just a few.’Buzzed driving is drunk driving.
PROVIDING SUPERIOR PRODUCTS & SUPPORT SINCE 1996
ASK ABOUT OUR BREAKER AUTOLUBE SYSTEMS!
Construction Equipment Guide • Attachments Section • www.constructionequipmentguide.com • February 9, 2013 • Page 29
© 2013 Helac Corporation. All rights reserved.
®
Learn more at www.helac.com
800.PWR.TILT
800.PWR.TIL
®
T800.PWR.TILLT
Learn more at www © 2013 Helac Corpora
.helac.comLearn more at www ved.All rights resertion. Helac Corpora t
.helac.com
Page 30 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
Doosan and the Doosan logo are registered trademarks of Doosan Corp. in the United States and various other countries around the world. ©2013 Doosan Infracore Construction Equipment America. All rights reserved. | 0113709
Doosan Delivers
Authorized Doosan Dealers
ARIZONADitch Witch of Arizona
Phoenix
Tucson520-579-0261
ditchwitchaz.com
CALIFORNIARGW Equipment Sales, LLC
Livermore925-606-2450
rgwequipment.com
Scott EquipmentFontana
www.scottequip.com
OKLAHOMAH & E Equipment Services, Inc.
Oklahoma City
Tulsa
he-equipment.com
OREGONFeenaughty Machinery Co.
Portland
feenaughty.com
TEXASTexas Timberjack, Inc.
Lu�in936-634-3365
Jasper
texastimberjack.com
UTAHMesco Inc.
North Salt Lake
mescoequipment.com
WASHINGTONCascade Trader Inc.
Chehalis
cascadetrader.net
Farmers Equipment CompanyBurlington
Lynden360-354-4451
farmersequip.com
Dean BlackBlack Construction Co., Devils Lake, ND
“A�er we demonstrated it, we purchased it the same week!”Doosan delivers solid machines, unsurpassed customer service and an expanding dealer network plus an unrivaled -hour parts guarantee.
Visit your local Doosan dealer to learn more. Scan the code or visit doosanequipment.com/dealer to see how close a dealer is to you.
iPhanozirf Ah octih WctiD
AONZRIA
wter neladegnidnapxed macilos sreviln deasooD
o
hlkOt SnempiuqH & E EOMHALKO
a
o DdzeirohtAu
puroh-d elavirnn us auk plrowemtosud cessaprsun, usenihd mac
s
t Ci.cn, Isecivret S
AOM
real Denaso
.eetnauar gstar pnd ane acivrer se
ket Llh StN.cn IcoseM
HATTAU
mocp.iuqettocs.www
aanntoFtnemipqu EttocS
moc.tnempquiewgr50426-60-529eromrveiL
, Lsealt SnempiuqW EGRAIRNOFILACmoc.zhactiwhctid
1620-975-025noscuT
xinoePh
ni�uLrebim TsaxeT
AXTEy.thguaneef
andltroPa Myy MhtaugneeFONGOREempquie-eh
asluT
omahalkO
CL, L
sremarF
saCW
me
n.cn I,ackjr
SAmocy.
and.o Cy renihca
ONmoc.tn
a
yt Cioma
mocp.iuqesremraf1544-45-3063
nednLy
ntognilruByanmpo Ctnemipqu Es
ten.radertadecsac
islahheC.cnr Iedare Tdacs
NOINGTHSAWWAmoc.tnmepiuqeocsme
keat Llah StroN
p.q
ajrebmitsaxte
epsJa3-436-369
m oc.kca
re5363
p.q
WAUKESHA-PEARCE INDUSTRIES, INC.
12320 S. MainHouston, TX 77035
713-723-1050Fax: 713-551-0798
Tomball, TX281-351-9016
Kilgore, TX903-984-2011
Port Arthur, TX409-721-5305
Corpus Christi, TX361-884-8275
Edinburg, TX956-386-0107
San Antonio, TX210-648-4444
Pflugerville, TX512-251-0013
Buffalo, TX903-322-7150www.wpi.com
Komatsu Equipment Company1486 South Distribution Drive
Salt Lake City, UT 84104801-972-3660
4460 Pioneer WayElko, NV 89801775-753-7557
3825 Losee RoadNorth Las Vegas, NV 89030
702-399-1004
900 Marietta WaySparks, NV 89431775-356-1334
6253 West Gilbert Industrial CourtHurricane, UT 84737
435-986-1000
10790 South Highway 59Gillette, WY 82718
307-682-1445
Rock Springs, WY307-686-1300
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 31
Efficient Komatsu Tier 4 Interim engine and automatic shift transmission with lockup torque converter maximize productivity while saving fuel.PLUS (long life) undercarriage is standard, further reducing our already low operating costs.Komatsu CARE provides complimentary Tier 4 maintenance, including KDPF exchange filters. Contact your Komatsu distributor for details.
Komatsu has once again made a great machine even better. The new D65-17 increases productivity and operator comfort while lowering operating costs. All designed to improve your bottom line.
D65-17 From Komatsu – The Dozer Experts
www.komatsuamerica.com
.komatsuamerica.comwww
.komatsuamerica.com
KIRBY-SMITH
MACHINERY INC.6715 W Reno
Oklahoma City, OK 73137800-375-3339405-495-7820
Fax: 405-787-5973
12321 E. Pine StreetTulsa, OK 74116800-375-3733918-438-1700
Fax: 918-437-7065
Abilene, TX877-577-5729325-692-6334
Amarillo, TX800-283-1247806-373-2826
Dallas, TX800-753-1247214-371-7777
Ft. Worth, TX877-851-9977817-378-0600
Lubbock, TX866-289-6087806-745-2112
Odessa, TX877-794-1800432-333-7000
www.kirby-smith.com
POWER MOTIVE CORPORATION
5000 Vasquez Blvd.Denver, CO 80216303-355-5900
Fax: 303-388-9328
Colorado Springs, CO719-576-5541
Grand Junction, CO970-241-1550
Milliken, CO970-339-4098
www.powermotivecorp.com
ROAD MACHINERY LLC4710A E. Elwood • Suite 6-7
Phoenix, AZ 85040602-252-7121
Fax: 602-253-9690
Gilbert, AZ480-545-2400
Tucson, AZ520-623-8681
Prescott, AZ928-778-5621
Albuquerque, NM505-345-8383
Farmington, NM505-324-8601
El Paso, TX915-872-1001
Bakersfield, CA661-695-4830
Freemont, CA510-659-1903
Perris, CA909-355-3600
Redding, CA530-229-3822
Sacramento, CA916-375-3540
Cananea, Sonora, Mexico011-52-6453328300
www.roadmachinery.com
Page 32 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
Powering Your Productivity...For Over A Century
Portable Power
©2013 Doosan Infracore Portable PowerFind Us on DoosanPortablePower.com (800) 633-5206 Follow Us on
Air CompressorSolutions, Inc.
TEXASOdessa
(432) 335-5900
Ditch Witch of Arizona
ARIZONAPhoenix
(602) 437-0351
Ditch Witch of SouthernArizona
ARIZONATucson
(520) 579-0261
Volvo ConstructionEquipment & Services
CALIFORNIABakersfield
(661) 387-6090
Fresno(559) 834-4420
San Leandro(510) 357-9131
Sacramento(916) 388-2244
San Diego/Lakeside(619) 441-3690
Corona(951) 277-7620
TEXASArlington
(817) 633-1010
Houston(713) 681-9221
OREGON7000 SW Sandburg Rd.
Portland(503) 639-8910
7909 N. Upland DrPortland
(503) 286-6400
29550 Airport RoadEugene
(541) 689-7407
500 Pech RoadMedford
(541) 779-3444
WASHINGTON9892 40th Avenue South
Seattle(206) 722-5800
19705 60th Avenue NE, Suite B1Arlington
(360) 474-8461
1307 54th Avenue EastFife
(253) 926-4386
3896 Irongate RoadBellingham
(360) 756-6572
909 South 19th StreetYakima
(509) 248-5636
1224 North California AvePasco
(509) 545-1959
4890 Contractors DriveWenatchee
(509) 884-2934
5518 East BroadwaySpokane
(509) 536-7300
NEVADA25 Vista Boulevard
Sparks(775) 356-9333
Pacific Power Productswww.pac-power.com
6100 So. 6th WayRidgefield, WA 98642
(800) 882-3860(360) 887-5900
7215 So. 228th StreetKent, WA 98032(800) 882-3860(253) 854-0505
2343 Biddle Rd.Medford, OR 97504
1203 SW Lake Rd.Redmond, OR 97756
6615 East Mallon Ave.Spokane, WA 99212
Pape Material Handling Inc. / Bobcat Westwww.papemh.com www.bobcatwest.com
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 33
ASCO SUPPLY CO., INC.Austin, TX 512/272-8922San Angelo, TX 325/655-5666San Antonio, TX 210/333-8000Wichita Falls, TX 940/687-2726www.ascoeq.com
ABILENE NEW HOLLAND, LTD.Abilene, TX 800/382-9271www.anhltd.com
AMARILLO MACHINERY CO.Amarillo, TX 888/309-7800www.amarillomachinery.com
NUECES POWER EQUIPMENTCorpus Christi, TX 361/289-0066
800/848-0790Edinburg, TX 877/880-9120Laredo, TX 877/580-9140San Benito, TX 800/580-7140Victoria, TX 877/580-9130Vinton (El Paso), TX 877/580-9160www.npetx.com
BANE MACHINERY INC.Dallas, TX 800/594-2263Ft. Worth, TX 800/601-2263Tyler, TX 800/594-2200www.banemachinery.com
OKLAHOMA TERRITORY CONSTRUCTION EQUIPMENTOklahoma City, OK 405/948-6565Tulsa, OK 918/835-7200www.oklahomaterritoryequipment.com
APCO EQUIPMENTNorth Las Vegas, NV 800/574-4089www.apcoequipment.com
TRI-WEST TRACTOR, INC.Livermore, CA 877/TRACTORwww.tri-westtractor.com
RASMUSSEN EQUIPMENT CO.West Valley City, UT 800/453-8032www.rasmussenequipment.com
CLM EQUIPMENT CO. INC.Lafayette, LAPrairieville, LA 225/677-7838Sulphur, LA 337/625-5942Houston, TX 281/598-2500www.clmequipment.com
Page 34 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
Fox News’ Stuart Varney Addresses AED Members at ShowAED from page 8
Proxibid is an innovator at assisting auction compa-nies with collecting their bids and potential buyersonline.
IROCK manufactures crushing and screening plantsavailable from distributors across the country. (L-R)are Sean Donaghy, national sales manager; RobertNelson, general manager; and Terry Wilson, regionalsales manager.
Jeff Abele (L), Abele Tractor, Albany, N.Y., proudlyworks with Joe Tedesco, Gorilla Hammers, Randolph,Mass., to supply his customers with high-quality ham-mers that are priced right.
Merle Patzkowsky (L), managing partner, WaldonEquipment, shakes hands with Jim Cornelson, presi-dent, sales, Broce/Waldon, during the AED CONDEXshow in Las Vegas.
© 2008 ESCO Corporation.
KIRBY-SMITHMACHINERY, INC.
www.kirby-smith.com
6715 W. RenoOklahoma City, OK 73137
800/375-3339Fax: 405/787-5973
12321 E. Pine St.Tulsa, OK 74116800/375-3733
Fax: 918/437-7065
1629 Vision Dr.Abilene, TX 79602877/577-5729
3922 I-40 EastAmarillo, TX 79103800/283-1247
8505 So Central ExpwyDallas, TX 75241800/753-1247
1450 NE Loop 820Fort Worth, TX 76106
877/851-9977
3201 E Slaton RdLubbock, TX 79404
866/289-6087
7301 East I-20Odessa, TX
877/794-1800432/333-7000
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 35
Top models for great performance
Great performance from Dynapac’s rollers and paversDynapac is proud to present several new pneumatic tired rollers: the CP224, CP224W and CP274. Dynapac’s pneumatic tired rollers
and comfort. Exceptional features include a smooth start-stop system
Dynapac’s new F1000 series wheeled or tracked asphalt pavers
Dynapac’s drum rollers
dynapac.us.
www.dynapac.us
www.dynapac.us
BEE EQUIPMENT SALES LTD.2506 Slaton HighwayLubbock, TX 79404
806/745-1511Fax: 806/745-1542
AERIAL LIFTS
Manlifts
GRADALL / LULL
Sales - Service - Training
Modern Equipment
Sales & Rental
800-445-4381
CRANES
Crane Inspections
Specializing in Truck
Mounted Cranes
Modern Equipment
Sales & Rental
800/445-4381
ALL TYPES OF CRANES
INSPECTED AND CERTIFIED
Accredited by the US Dept.
of Labor Under 29CFR Part
1919 and Accredited by
CALOSHA
Call 215-639-2579
Atlantic Crane
Inspection Services
Visit us at
www.atlanticcrane.com
EXCAVATORS
Hydraulic Excavators
2008 Link Belt 130LX, 26,900
lbs, manual thumb, 24'' bucket,
excellent, 900 hours....$89,500.
Call Jason
405-850-6012
NH Construction Equipment
New & Used
Parts & Service
Modern Equipment
Sales & Rental
800-445-4381
2012 Hyundai R145CR-9,
enclosed cab, hyd. quick cou-
pler, thumb, 2 buckets, excel-
lent, 275 hours .........$137,500.
503-282-7211
Mini Excavators
NH Construction Equipment
New & Used
Parts & Service
Modern Equipment
Sales & Rental
800-445-4381
FORKLIFTS
Industrial Forklifts
GRADALL / LULL
Sales - Service - Training
Modern Equipment
Sales & Rental
800-445-4381
GENERATORS & GEN SETS
Generators & Gen Sets
For Sale or Rent
All Makes and Models
Modern Equipment
Sales & Rental
800/445-4381
LOADERS
Wheel Loaders
2012 Hyundai HL760 XTD-9,
Cummins power, enclosed cab,
air, GP bucket, new, 3 hours
..................................$164,500.
503-282-7211
NH Construction Equipment
New & Used
Parts & Service
Modern Equipment
Sales & Rental
800-445-4381
PARTS
Crane Parts
TEREX PARTS
Modern Equipment
Sales & Rental
800/445-4381
TRAINING
Operator Training
Are your operators compli-
ant with Federal Standards,
OSHA, ANSI, ISO?
MODERN GROUP
offers training for:
Front-end Loaders & Backhoes
Aerial work platforms (AWP)
(Boom & Scissor Lifts)
Rough Terrain Forklifts
(Gradall, Lull, JCB)
Skid Steer Loaders
For information, pricing or
reservations:
Call 1-800-223-3827
www.moderngroup.com
All prices include Trainer,
travel and material
NO HIDDEN COSTS
TRUCKS
Bucket Trucks
ELLIOTT BUCKET TRUCKS
Modern Equipment
Sales & Rental
800/445-4381
Classified Rates:30 Words or Less for $30.00. Each Additional Word is 95¢.For just an additional $20 your ad can be posted on our online searchable database
for 30 daysAd runs for 2 (two) insertions - no changes in second insertion.
PLEASE ENCLOSE PAYMENT WITH ORDER and mail to:470 Maryland Drive• Fort Washington, PA 19034
215/885-2900 • Fax 215/885-2910 • Toll Free 1-800/523-2200
CLASSIFIEDS
SECT IONTrucks & Trailers
John Deere E-Series Features North America’s Largest ADTAfter a successful intro-
duction at ConExpo-Con/AGG 2011, the newJohn Deere 460E ADT joinsthe 370E and 410E as part ofthe E-Series. The 460E, thehighlight of the three models,is Deere’s largest, most oper-ator friendly truck ever built.The 46-ton (41.7 t) model isnow John Deere’s largestarticulated dump truck everto hit the market.“The E-Series ADT is a
customer driven, ground updesign to meet and exceedthe durability, productivityand uptime needs of contrac-tors,” said Mark Oliver, ADTproduct marketing manager,John Deere Construction &Forestry. “We worked withroad builders, site develop-ers, and the mining, quarry andaggregate segments to developthree trucks that are purpose-builtto reliably handle various payloadsand move materials faster andmore efficiently on any job site inthe world.”Designed and built in
Davenport, Iowa, the E-SeriesADTs feature a John DeerePowerTech 13.5L IT4 engine withthree power levels based on themodel — 422 net hp (370E), 443net hp (410E), and 481 net hp(460E). A purpose built ZF trans-mission includes a high capacityretarder, eight forward gears andfour reverse gears. In addition, thenew John Deere hauler axles aredesigned for heavy-duty applica-tions and include on-the-fly differ-ential locks, outboard planetariesand each axle is independentlypressure lubed and filtered. The E-Series axles use internal wet discbrakes that utilize independentcooling circuits. “This new truck design offers
contractors some serious advan-
tages in the market, including highpower-to-weight ratios, gradabili-ty, and capacity,” said Oliver. “Oneof the biggest customer inspiredenhancements are the on the flydifferential locks that can beapplied at any speed, manually orautomatically, for improved per-formance in poor conditions.” Allowing the differential lock
system to run in automatic modewill simplify operation for newoperators by taking the guessworkout of using the differential locks.When ground conditions get softand difficult, the system will auto-matically control the axle differen-tial locks as well as the inter-axledifferential lock all while the truckis still moving. An experiencedoperator can still choose to manu-ally engage the traction controls.The new ADTs incorporate
high-strength materials to providedurable, long lasting structureswhile still keeping a strong focuson overall weight and distribution.This provides increased power-to-weight ratios and hauling efficien-
cies. A newly designed stay-tightoscillation joint, high-suspensiontravel on all axles, and balancedweight distribution also providethe agility and ability to navigatehostile terrain. To minimize therisk of rollover while unloading,the dump body can be restricted
from rising when the rearchassis exceeds a predeter-mined slope angle.Another new customer
driven feature of the E-Seriesand a hallmark for JohnDeere is centralized, trueground level servicing tosimplify daily maintenanceand overall serviceability. Alldaily service can be complet-ed from the ground. In addi-tion, the all-new John Deereadaptive suspension controlsystem improves stability toincrease productivity on thework site. This new suspen-sion system is standard on allE-Series ADTs.
Hydraulically controlled fans withswing out cooling packages onboth sides of the engine highlightthe cool on demand system. Fordusty environments, there is areversible fan option available forsimplified cooler cleanout. The cab monitor provides an
easy to read LCD screen withonboard diagnostics, analog/digitalgauges, and vital system indica-tors. Two ergonomically posi-tioned sealed switch modules sim-plify operation and conveniencecontrols. The auto shutdown fea-ture turns off the engine after anowner-determined period of inac-tivity to help save fuel while reduc-ing emissions, idle time operation,and subsequent wear on the powertrain and hydraulics.An on board weighing (OBW)
system allows contractors to viewthe weight and the number of loadscarried via JDLink, improvingproject management and equip-ment utilization. This OBW sys-tem not only allows the customerto track and optimize payload per-formance of an E-Series ADT, butalso will aid in maximizing the lifeof the tires and chassis. The truckhas mirror-mounted load indicatorlights that illuminate for the load-ing operator as the truck approach-es capacity (yellow), is at capacity(green), or overload (red). An integrated tire pressure mon-
itoring system helps maximizetraction, tire life and fuel efficiencyand access to JDLink Ultimateallows customers to check tirepressures remotely and receivealerts when the pressure gets toolow or too high.For those fleet managers, own-
ers or operators looking to get themost out of their equipment, a stan-dard three-year subscription ofJDLink Ultimate continuously col-lects and transmits machine datafor machine management. The sys-tem enables timely preventivemaintenance and remote diagnos-tics, as well as the coordination ofmachines working on multiple jobsites to get the right machine to theright place at the right time. For more information, visit
www.JohnDeere.com.
Pages 36-38
The E-Series ADTs feature a John Deere PowerTech 13.5L IT4 engine withthree power levels based on themodel — 422 net hp (370E), 443 nethp (410E), and 481 net hp (460E).
Allowing the differential lock system to run in automatic modewill simplify operation for new operators by taking the guess-work out of using the differential locks.
Construction Equipment Guide • Trucks & Trailers Section • www.constructionequipmentguide.com • February 9, 2013 • Page 37
Stage 8 Mechanical LockingFasteners Stay Tight on Trucks Stage 8, an active mechanical locking sys-
tems manufacturer, now has applicationsthat keep work trucks on the road.Any mechanic will confirm that shock,
pressure, vibration and temperature changeall combine to loosen fasteners, whichinevitably come loose at the worst possibletime. Stage 8 provides
application specificlocking fasteners inan unlimited rangeof sizes, materials,thread pitches andretainer configura-tions. The system isdesigned to stop threaded joint failure anddowntime by preventing fastener looseningfrom starting, according to the manufacturer. Stage 8’s GrooveLok fastener locking
system acts like a small wrench locked ontoa bolt head, with the wrench (Stage 8 lock-ing retainer) braced against a stationaryobject, such as a frame, casting or protrusion.This stops any counter rotation of the boltuntil the locking system is removed. Thesystem works the same way with nuts. It
includes a grooved nut, an application spe-cific retainer, which serves as the “wrenchsocket and handle”, and a spring clip, all ofwhich combine to work together. “When you see the clip and retainer
locked in place, you know the fasteners havemaintained their full pre-load,” said RobertAhern, Stage 8 manager. “Until you remove
the clip and retainer,the nut or bolt willnot budge. The Stage 8 sys-
tem retrofits exist-ing components, isfully reusable andworks on items as
small as eyeglass screws, to bolts as large as8-in. (20 cm) in diameter holding generatorpropellers onto a hydroelectric dam. To date,the system has no reported failures in morethan 17,000,000 applications, according tothe manufacturer.Stage 8 manufacturers many types of
active, fail-safe mechanical locking fastenersincluding locking header bolts. For more information, call 800/843-7836
or visit www.stage8.com.
Trail King Introduces New Detachable Gooseneck TrailerTrail King’s new mechanical
detachable gooseneck (MG) trailerdelivers lightweight strength, maxi-mum corrosion resistance and long-lasting good looks.The upper deck and the wheel area
of the new MG feature aluminumcross members and outer rails asstandard equipment, to deliver opti-mum corrosion resistance as well assignificant weight savings. In fact,the new MG is 750 to 1,000 lbs. (340to 453 kg) lighter than previous mod-els, according to the manufacturer.The standard cross members in the
main deck are 8 in. (20 cm) I-beamsalternating with 4 in. (10 cm) I-beams for 12 in. (30 cm) spacing inthe outer bays, although aluminum cross members areavailable as an option, as are aluminum box beam crossmembers to accommodate optional aluminum pullouts.The MG still features four steel main I-beams con-
structed of one-piece web and flange material that iswelded on all four sides to seal and protect the seamsfrom rust and corrosion. Then all steel is primed andpainted with two-component urethane primer and two-component polyurethane paint before decking or any air,hydraulic or electrical lines are installed. This includesthe new wheel area, where the deck and the wheel areaare both primed and painted separately before being huck
bolted together. The result is maximum corrosion resist-ance, even in places you can’t see, according to the man-ufacturer.The wheel area on the new MG also is designed with a
longer and deeper mini-boom trough to better accommo-date the hitches on agriculture equipment, as well asmany kinds of construction equipment.Other standard equipment on the new MG includes:• Gooseneck reinforced for flip• Removable gooseneck rollers• Air-activated, positive self-locking pin for the goose-
neck• Bent-style D-rings and outrigger brackets
• Adjustable ride height control• Wide Load sign, flag, and strobe light brackets• And much moreThe Mechanical Detachable Gooseneck trailer is avail-
able in 60-, 75-, and 90-thousand-lb. (27,215, 34,019 and40,823 kg) capacities.In addition to the new mechanical detachable goose-
neck, Trail King manufactures a complete line of trailers,including tags, tilts, hydraulic detachable lowboys, andhydraulic tails and sliding axles; end dump, bottom dump,and side dump trailers; live bottom trailers; pneumatic drybulk trailers; and hydraulic platform trailers and multi-axle trailers for the specialized hauling industry.
The standard cross members in the main deck are 8 in. (20 cm) I-beams alternating with 4 in. (10 cm) I-beams for 12 in. (30 cm)spacing in the outer bays, although aluminum cross members are available as an option, as are aluminum box beam cross mem-bers to accommodate optional aluminum pullouts.
Page 38 • February 9, 2013 • www.constructionequipmentguide.com • Trucks & Trailers Section • Construction Equipment Guide
Cat Lift Provides Trucks for2013 Houston Livestock ShowMore than 2 million people and 30,000
animals are expected at Reliant Park for the2013 Houston Livestock Show and Rodeo inFebruary and March. Behind the scenes CatLift Trucks will provide the equipment andexpertise, including more than 100 lifttrucks, needed to prepare for the massiveinflux of show-goers and livestock.In its ninth year as the official lift truck
provider for the Houston Livestock Showand Rodeo, Cat Lift Trucks and local dealerAdobe Equipment Houston LLC (Adobe)will provide a broad range of internal com-bustion pneumatic tire lift trucks ranging incapacity from 5,000 to 36,000 lbs. (2,268 to16,329 kg) to meet the material handlingneeds of the show.Used exclusively throughout the more
than 300-acre Reliant Park, the Cat lift truckswill be used daily to unload trailers of everysize and move tons of animal feed, lumber,food supplies, water, visitor guides, mer-chandise and more. The trucks also will facilitate setup and
teardown of all exhibits and equipmentneeded for nightly performances, includingthe stage materials, platforms and audiovisual equipment that allow the show to hosta star-studded lineup of country music and
pop artists.Adobe technicians also will provide train-
ing for lift truck operators and will be onhand around the clock to service and supportall donated lift trucks, demonstrating Cat LiftTrucks continued commitment to qualityservice.“As a Houston-based manufacturer, we’re
proud to support our city’s world-renownedlivestock show and rodeo and contribute tothe immense benefits it brings to our com-munity every year,” said Kent Eudy, vicepresident of sales and marketing of Cat LiftTrucks. “We’re honored we can play animportant role in helping the show runsmoothly.”The Cat Lift Trucks scholarship program,
now in its ninth year, will award a $5,000scholarship to an exemplary Houston-areastudent pursuing higher education in amechanical engineering or business-relatedfield. The winner will be announced on theCat Lift Trucks Facebook page on Feb. 26.The 2013 Houston Livestock Show and
Rodeo will begin Feb. 25 and run throughMarch 17. Learn more about Cat Lift Trucksinvolvement at the show at www.face-book.com/catlifttrucks or www.cat-lift.com.
HxGN LIVE – Hexagon’s International Conference, 3 – 6 June, 2013, Las Vegas, Nevada, USA!Join Leica Geosystems at the HxGN LIVE Conference –formerly known as Hexagon 2013! It’s a different name,but the same great conference – and an experience youdon’t want to miss. Group registration options and spe-cial discounts for previous conference alumni, educa-tional institutions, law enforcement agencies, andauthorized dealers are also available. For moreinformation contact: Angelique Ortega Angelique.orte-ga@leicaus.com +1 925/790-2318. See you in LasVegas!
Illinois Association of Aggregate ProducersFATALITY FREE 2012 for ILLINOIS AGGREGATE PRO-DUCERS! Congratulations go out from the IAAP Safety Committeeto everyone working in the aggregate mining industry forIllinois for another fatality free year! That’s nine years ina row working together ensuring Illinois is one of thesafest places to be a miner. As in previous years, theSafety Committee will celebrate this achievement by con-ducting a hardhat sticker design contest awarding a$250 cash prize to this year’s winner. Please take thisopportunity to express your creative talent by submittingone or more designs for consideration. Each entryshould clearly show the colors and state the safety slo-gan or other lettering you would like us to see on thesticker. Submit your art work by email to: IAAP OutreachManager Shawn McKinney atshawn@hansoninfosys.com or by mail to: IAAP, 1115South Second Street, Springfield, Illinois 62704, on orbefore February 26, 2013. A winning entry will be cho-sen the next day by the IAAP Safety Committee thenreproduced for distribution to member companies in thespring.
ARA The Rental Show is February 10-13 at a new LasVegas location: The Sands Expo and ConventionCenter, right in the middle of the Las Vegas Strip. Clickon www.therentalshow.com for a detailed schedule andmore information.
AGC of America Annual Convention: Registration isnow open for the 2013 AGC Annual Convention andConstructor Expo, being held March 6 – 9 in PalmSprings. Room availability at the convention headquar-ter hotel (JW Marriott Desert Springs) is limited, so reser-vations should be made as early as possible. Complete
conference details are available athttp://convention.agc.org or you may contact DeniseWoods, CMP, Director, Communications & Events, AGCof Minnesota, directly at 651/796-2186; toll free at800/552-7670 or website: www.agcmn.org.
2013 ANNUAL PAVING SEMINARTuesday, February 26, 2013Brought to you by Kirby-Smith Machinery, Inc., ThePaving AuthorityWho Should Attend: Owners – Superintendents –Equipment OperatorsArlington Convention Center1200 Ballpark WayArlington, Texas 760117:30 AM Registration 8 AM to 4 PM (lunch provided)Reservations Required by February 15, 2013To Register, go online at:www.kirby-smith.com and click on the Paving Seminarlink. ***limited seating!Morning Breakout Sessions:. Milling. Paving. Soil Stabilization. CompactionAfternoon General Sessions:. New Technology in Hot Mix Designs Including RAPand RAS. Advanced Theory “Cold in Place Recycling”. Paver Tamper Screeds and Emulsion Advancements. Advanced Paver and Milling Grade ControlExhibit Hall Equipment Displays:. Complete Asphalt Paving Train. From Utility to Mainline Milling Machines. Latest Design in Soil Stabilizers. Introduction to Oscillating Compaction2013 MAASTO CONFERENCE: The WisconsinDepartment of Transportation will host the Mid-AmericaAssociation of State Transportation Officials (MAASTO)2013 Conference – “Sharing Strategies for Success.”The conference will be held JULY 16-19 at the HILTONHOTEL in downtown Milwaukee. One of the major eventsat MAASTO 2013 will be a trade show, where industryrepresentatives will have the opportunity to showcasematerials, technology, and professional services. Thetrade show will be held July 17 and 18 at the conferencehotel. More information on the trade show registration,layout, schedule, and fees will be available in early
2013 at the conference website, which will be linked viathe MAASTO meetings webpage –http://www.maasto.net/meetings.html. If you are lookingto speak to someone with regard to the above confer-ence you may contact Denise Woods, CMP, Director,Communications & Events, AGC of Minnesota, directly at651/796-2186; toll free at 800/552-7670 or website:www.agcmn.org.
AGC St. LouisConstruction Leadership Council MARDI GRAS FLOATThe AVENGERS of Construction SafetySOULARD MARDI GRAS PARADEFebruary 9, 2013Please Dress in Hero Gear & Safety Construction Attire$80 per Ride: Price includes beer, beads and a greatride on the CLC Float!First come, First served: Limited availability!!! Registration Deadline: February 1, 2013Fax: (314) 781-2874FLOAT: $80 per RiderSponsorship Package: $500 (sponsorship & 4 riders)PROCEEDS go to the Jeff Staley Safety Foundation.Questions ??? Please contact: Jackie McMahon at(301) 659-9090 or Email: Jackie.McMahon@affinity-center.comAGC – St. Louis***SAVE THE DATE!Beer, Brats & a Band … What more do you need?JUNE 13, 2013 (more details to follow).AGC – St. LouisSAFETY BANQUET – FEBRUARY 21, 2013(Details to Follow)
AGC of Minnesota Sales and Use Tax Seminar – Wednesday, February 13,2013Do you know when you become a contractor-retailer?Or the definitions of real property and tangible personalproperty? If you pay tax on material from another state,do you owe the full Minnesota use tax on those materi-als? Get the answers to these and many other tax
questions on Wednesday, February 13. Please email:info@agcmn.org or contact AGC’s website:www.agcmn.org or telephone (651) 632-8929 or(800) 552-7670 for more information.
March 5-6, 2013 – 2013 Ohio Asphalt Expo,Columbus, OHRegistration is now open for the Ohio Asphalt Expo onMarch 5 thru 6, 2013 at the Columbus/Polaris HiltonHotel located at 8700 Lyra Drive, Columbus, Ohio43240.Office address and contact information: 6205 EmeraldParkway, Suite B, Dublin, OHPhone: 614/791-3600; Toll Free: 1/888-4HOTMIX;Email: info@flexiblepavements.org.
GENERAL AGGREGATE EQUIPMENT, Fargo, NDTOP AGGREGATE INDUSTRY EQUIPMENT MANUFACTUR-ERS GATHER FOR EVENT!General Equipment & Supplies, Inc. and GeneralAggregate Equipment Sales expect around 300 atten-dees at their third Aggregate Seminar. The two-day eventwill be heldMARCH 5-6, 2013 at the Holiday Inn in Fargo, ND. If you would like more information on this event, or toschedule an interview with Don Shilling, please contactSara Frith at 701/364-2104 or sfrith@genequip.com.
March 6 - 8, 2013 – NTEA/THE WORK TRUCK SHOW,Indianapolis, INThe must-attend event for the work truck industry.. 500,000 sq. ft. of vocational trucks and equipment. Newest products and technical support from more than550 exhibitors. More than 60 educational sessions on top-of-mindindustry issuesFor more information on this event: Phone: 248/489-7090; Toll Free: 800/441-6832;Email: info@ntea.comStaff.
MARCH 19 – 21, 2013 – OAIMA (Ohio Aggregates &Industrial Minerals Association)Aggregates Academy & Expo, San Antonio, TexasAGG1 Aggregates Academy & Expo focuses exclusivelyon the aggregates industry as its leading educationresource. This event combines a plethora of educationsessions led by experts in virtually every segment of theaggregates industry with the latest innovations in equip-ment, technology and software on the AGG1 Expo show
floor. REGISTER TODAY at www.AGG1.ORG.You may contact the OAIMA at 1-800/OH.ROCKS.614/428-7954. Fax: 614/428-7919.
March 19 – 21, 2013 – World of Asphalt , San Antonio,TXDon’t miss the Industry’s Main Event! Register to attendand save 40%. Exhibit Show Floor is Almost Sold Out!Hurry, space is still available but going fast. Reservespace today!Co-located with AGG1 Aggregates Academy & ExpoMarch 19 – 21, 2013, San Antonio, TX, USA, Henry B.Gonzalez Convention CenterWorld of Asphalt Show & Conference is the leadingexposition and education resource for the asphalt indus-try. The event features in-depth industry-focused educa-tional programming and comprehensive exhibits thatshowcase the latest technologies and innovations inasphalt-related equipment, products and services. World of Asphalt Show Management: Association ofEquipment Manufacturers6737 West Washington Street, Suite 2400, Milwaukee,WI 53214-5647 USAToll Free Telephone: 800/867-6060 or contactinfo@worldofasphalt.com.
March 20 & 21, 2013 – 34th West Virginia Construction& Design ExpositionThe region’s largest trade show for the Construction andDesign Industries invite you to be a part of the 34th
Annual Exposition – EXPO!The Contractors Association of West Virginia, AmericanInstitute of Architects – WV Society of ProfessionalEngineers & WV Utility Contractors Association, with thesupport of 24 co-sponsors, want the opportunity tomake EXPO work for you. Let us hear from you, if youhave questions! expo@wvexpo.com. Pat Parsons,Show Manager and Alice George, Office Manager
April 23, 2013 IAAP CONVENTIONThe IAAP’s 45th Annual Convention is scheduled forTuesday, April 23, 2013, at the Crowne Plaza Hotel inSpringfield, Illinois. As always, our program will featurea series of educational seminars focusing on topics ofinterest to aggregate producers and to the companiesselling goods and services to the mining industry. MAKEPLANS TO ATTEND THE 45th ANNUAL IAAP CONVEN-TION!
BusinessCalendar
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 39
NEED 12 MONTHS BULLDOZER D3ATD10 1978 AND UP. WANT TO BUY FROMCONTRACTOR ONLY. BULLDOZER NOTADVERTISED USA.CONTACT: JEAN MAURICE BOUTINPHONE: 1 450 346 8975 OR 1 514 386 8975EMAIL:JEANMAURICEBOUTIN@VIDEOTRON.CA––––––––––––––––––––––––––––––––TEREX TR100 | LOOKING FOR TEREXTR100 DUMPTRUCKS, 2-4 UNITS. MUST HAVE EPA.CONTACT: JERRYPHONE: 0031227570364EMAIL: INFO@EMO-MAC.COM––––––––––––––––––––––––––––––––MOTOR GRADERS | WE ARE LOOKINGTO PURCHASE SEVERAL UNITS OF140H (99 - 02), AND 14 G/H (72 - 00)CATERPILLAR MOTOR GRADERS,PREFERABLY WITH RIPPER. GRADERSMUST BE GOOD LOOKING AND INWORKING CONDITION WITH OLDPAINT. SEND PICTURES, CONDITION,SERIAL NUMBER AND FINAL OFFERPRICE.CONTACT: AIMN BLBOLPHONE: +971504814823EMAIL: SALE@ALWAFAEQUIPMENT.COM––––––––––––––––––––––––––––––––LOOKING FOR LARGER IMPACTCRUSHERS - SCREENS - CONVEYORS -SCALES IN THE MIDWEST REGION.EMAIL: ROCKSHYLLC@GMAIL.COM––––––––––––––––––––––––––––––––USED CARGO VANS | WANTED 100USED CARGO VANS FLEETS ONLY,AS MANY AS POSSIBLE NO DEALERSPLEASE.CONTACT: FRANKPHONE: 570-562-3291EMAIL: CARGOVANMAN@AOL.COM––––––––––––––––––––––––––––––––CATEPILLAR GRADER 12G AND 140G |IF YOU HAVE ANY IN STOCK PLEASESEND PICTURES AND DETAILS.CONTACT: RIZ SUNESARAPHONE: 832-528-0786FAX: 281-727-0415EMAIL:RIZ@MEGAEQUIPMENTS.COM––––––––––––––––––––––––––––––––CATERPILLAR 926E AND 936F | I NEEDURGENT CAT 930, 926E AND 936F,PLEASE SEND ME PICTURES ANDDETAILS.CONTACT: ABDAL SALEEMPHONE: 966 3 842 8312FAX: 9666 3 312326EMAIL:HAJICONSTRUCTEST@GMAIL.COM––––––––––––––––––––––––––––––––ANY CONSTRUCTION EQUIPMENTWANTED | LOOKING FOR CAT 330CL/DL <3000 HOURS, AUX HYD. FORCONTRACTOR EXCAVATORS DOZERSLOADERS COMPACTORS ARTICULAT-ED TRUCKS OFF HIGHWAY TRUCKSMOTOR GRADERS SCRAPERS ONROAD TRUCKS BUYING OR SELLINGLET JOE KNOW!CONTACT: JOEPHONE: 570-360-5162EMAIL: JOEDIRTMACH@AOL.COM––––––––––––––––––––––––––––––––
CONSTRUCTION | WANTED**** ANYLONG REACH BOOMS OR STICKS.LONGER THEN NORMAL BOOM ORSTICK. LONG REACH EXCAVATORFRONTSCONTACT: TYLER PALUMBOPHONE: 330-365-0654EMAIL: PALUMBO519@HOTMAIL.COM––––––––––––––––––––––––––––––––MOBILE TRAILERSEMAIL:ORLANDOGEERMAN@GOOGLE.COM––––––––––––––––––––––––––––––––LOOKING FOR BACKHOES. PLEASECALL OR EMAIL WITH WHAT YOUHAVE.CONTACT: CODYPHONE: 1(810)834-2571EMAIL:CODY.CROOKEDACRE@AOL.COM––––––––––––––––––––––––––––––––TELEHANDLER | 6-8,000 LBS TELEHAN-DLER WITH 40FT REACH. 2005 ORNEWERCONTACT: MANAGERPHONE: 618 789-0449FAX: 8886510449EMAIL:GRANDRENTAL@CONSOLIDATED.NET––––––––––––––––––––––––––––––––ATLAS COPCO | ATLAS COPCO’S XAS750 JD7 TIER 4A COMPRESSOR MEETSNEW EMISSION STANDARDS. SENDASKING PRICECONTACT: MR MO ALABEDEPHONE: 00353899674351EMAIL: MMALABEDE77@GMAIL.COM––––––––––––––––––––––––––––––––PILE HAMMERS | ALWAYS SEEKING TOPURCHASE VIBRATORY PILE HAM-MERS OF BRANDS ICE, PVE, APEAND/OR MKT. QUICK CASH AVAILABLEFOR YOUR USED/SURPLUS PILE HAM-MERS. EMAIL WITH PICS/SPECS ONYOUR SURPLUS PILE HAMMERS.CONTACT: JEFF LAWSONPHONE: 864-542-4369EMAIL: JLAWSON29321@CHARTER.NET––––––––––––––––––––––––––––––––WE SELL ALL KINDS OF EQUIPMENTMANUALS. GIVE US A CALL, WE MIGHTHAVE WHAT YOURE LOOKING FOR.CONTACT: GRACE FRANCESPHONE: 270-849-2270EMAIL: TRITOWN1@MSN.COM––––––––––––––––––––––––––––––––LULL 844 TT 34 PARTS MACHINE ORPARTS NEW OR USED.CONTACT: SEANPHONE: (815)566-0442FAX: (815)827-3246EMAIL:SEAN.MANINGER@YAHOO.COM––––––––––––––––––––––––––––––––KOMATSU PC308 TRACK EXCAVATOR |LATE MODEL, LOW HOUR EAST COASTUSA LOCATIONCONTACT: RICHARDPHONE: 603 828-6100EMAIL: CMIEQUIP@YAHOO.COM––––––––––––––––––––––––––––––––OLD CHAMPION ROAD GRADERCONTACT: ALVIN WALDNERPHONE: 605-778-6776FAX: 605-778-6778 |EMAIL:GR.ALVIN@SDCOLONY.COM––––––––––––––––––––––––––––––––
NEEDED BULLDOZER D6N LGP ENCCAB USER USA LOW HOURS LOWPRICE • WANT TO BUY FROM USA«CONTRACTORS D6N LGP D7G D8KCONTACT: JEAN MAURICE BOUTINPHONE: 1-450-346-8975 OR MOB 1-514-386-8975EMAIL:JEANMAURICEBOUTIN@VIDEOTRON.CA––––––––––––––––––––––––––––––––WE BUY EQUIPMENT MANUALS (USEDOR NEW). WE PREFER 100 OR MORE.CONTACT: GRACE FRANCESPHONE: 270-849-2270EMAIL: TRITOWN1@MSN.COM––––––––––––––––––––––––––––––––CATERPILLAR D8R DOZEREMAIL: RMJANSEN70@YAHOO.COM––––––––––––––––––––––––––––––––WE NEED 2X 50T RIGID DUMP TRUCK.PRICE ~ 50K USD.CONTACT: JERRYPHONE: 0031227570364EMAIL: INFO@EMO-MAC.COM––––––––––––––––––––––––––––––––CAB OR CANOPY FOR AN OLDER CAT120 GRADER • WE ARE LOOKING FORAN ENCLOSED CAB OR CANOPY FORA CATERPILLAR 120 MOTORGRADER. •THINK THAT A CAB OR CANOPY OFFOF A 12E OR F WILL WORK ALSO.PLEASE OFFER WHAT YOU HAVE.CONTACT: WENDELL CAINPHONE: 001-770-381-8984FAX: 001-770-381-6977EMAIL:WENDELL@CAINANDTODD.COM––––––––––––––––––––––––––––––––BOBCAT SKID STEER LOADERS • AMLOOKING FOR CONTRACTORS ORLANDSCAPERS WHO ARE LOOKING TOSELL THEIR USED BOBCAT BRANDSKID STEER LOADERS THAT ARELOCATED IN THE SOUTH EASTERNUNITED STATES. • PREFER LARGEFRAME MACHINES, S330, S300, S250,T320, T300, T250 EQUIPPED WITH THE"GOLD PACKAGE", BUT I WILL BUYANY BOBCAT THAT YOU HAVE FORSALE. DONT TRADE IT IN, SELL IT TOME. **DEALERS - DONT WASTE YOURTIME RESPONDING**CONTACT: WARRENEMAIL: TWOPETIES@AOL.COM––––––––––––––––––––––––––––––––AM LOOKING TO BUY CONSTRUCTIONEQUIPMENT REPAIR MANUALS FORLATE MODEL NAME BRAND CON-STRUCTION EQUIPMENT.CONTACT: WARRENEMAIL: NYERGESEQUIPMENT@HOTMAIL.COM––––––––––––––––––––––––––––––––ROTO TILLER ATTACHMENTPHONE: 250-378-7505EMAIL: MCKIRK@SHAW.CA––––––––––––––––––––––––––––––––1000 OR MORE ROAD MACHINERY.CONTACT: SAEED.MPHONE: +98-912-472 29 89FAX: +98-21-48 62 295EMAIL:MOHAMMADI.SAEED63@GMAIL.COM––––––––––––––––––––––––––––––––
DRI PRIME DIESEL PUMPS • 6X6 AND12X12 VACUUM OR VENTURI DIESELPUMPSCONTACT: MICHAEL COPPOLAPHONE: 973-962-1890FAX: 973-962-9112EMAIL:MCOPPOLA@COPPOLASERVICES.COM––––––––––––––––––––––––––––––––TOWERS/STEEL STAIR CASES, STEELLADDERS WANTED IN EXCHANGE FORDEER HUNTING. WWW.SIKASTAG.COMCONTACT: PERCY RANSOMEPHONE: 215-350-1165EMAIL: PERCY.RES@GMAIL.COM––––––––––––––––––––––––––––––––ESTACION TOTAL TOPCON GTS 105NCONTACT: GONZALO REYES MOSCOSOEMAIL: GOREMO62@GMAIL.COM––––––––––––––––––––––––––––––––LOOKING TO PURCHASE USEDKAWASAKI WHEEL LOADERS FROM50Z TO 95Z (SERIES II, IV, V), YEARMODEL 2003 AND BELOW. MACHINESMUST BE GOOD LOOKING AND INWORKING CONDITION WITH OLDPAINT. PLEASE SEND PICTURES, YEARMODEL, SERIAL NUMBER, MACHINECONDITION AND FINAL OFFER PRICE.CONTACT: AIMN BLBOLPHONE: +971504814823FAX: +97165355291EMAIL: SALE@ALWAFAEQUIPMENT.COM––––––––––––––––––––––––––––––––TRADE TWO 29529 FIRESTONE SUPERROCK GRIP TIRES 60% FOR TWO 29529DIRT TIRESCONTACT: KEVIN SANSALONEPHONE: 856-297-4758FAX: 856-362-5602EMAIL:KEVIN@SANSALONEEXCAVATING.COM––––––––––––––––––––––––––––––––HEAVY HAUL MURRAY TRAILER •LOOKING FOR A GOOD USED MURRAYTRAILER TO HAUL 623 SCRAPERS,WATER WAGONS, 47 TON OVER THEBACK LOADING, EXPANDABLE RUN-NING GEAR, DETACHABLE WIDE NECKWITH A 21’ 6" DECK.CONTACT: EMMETT O LEARYPHONE: 520-349-3526FAX: 520-798-0740EMAIL:EMMETT@OLEARYCONSTRUCTIONAZ.COM––––––––––––––––––––––––––––––––UNDER SLUÑG CRANE ROLLERS 5TON• S TYPE BEAM TAPER FLANGE15IN./5.5IN.WIDE (NEED 3)CONTACT: MIKE FEMOYERPHONE: 904-497-9285EMAIL: MIKEFEMOYER@GMAIL.COM––––––––––––––––––––––––––––––––A WELL DRILLER THAT CAN BE OPER-ATED BY ONE OR TWO PEOPLE.CONTACT: B. SMITHPHONE: 509-368-9174EMAIL: BRENTWFSMITH10@YAHOO.COM––––––––––––––––––––––––––––––––
CAT 307 OR CAT 308 EXCAVATOR • CANBE ANOTHER BRAND EQUAL SIZE.NEEDS TO HAVE LEVELING BLADEAND HYD THUMB. OFFSET BOOMWOULD BE NICE. MID 90 MODEL.UNDER 20,000CONTACT: BEN SEAYPHONE: 706-871-0100EMAIL: SEAYIV@ATT.NET––––––––––––––––––––––––––––––––WE ARE LOOKING TO BUY DOZER D9ROR D9N FROM 1990 UP TO 1997CONTACT: OUFIPHONE: 966 530185141EMAIL: ALOUFI01@HOTMAIL.COM––––––––––––––––––––––––––––––––CONCRETE CORE DRILL AND 6" BIT,AND TRENCH BOX 20X10 WITH 42" AND30" SPREADERSCONTACT: ROMEY WILLIAMSONPHONE: 3042725923FAX: 3042725823EMAIL:ROMEY68@YAHOO.COM––––––––––––––––––––––––––––––––LOOKING FOR CATERPILLAR WHEEL-LOADERS & HITACHI EXCAVATORS •WE NEED THE FOLLOWING CATERPIL-LAR WHEEL LOADERS 950, 950B, 950E,966F & HITACHI EXCAVATORS EX200,EX400. FEEL FREE TO CONTACT US.CONTACT: HIDAYAT KHANPHONE: +92-345-8818803EMAIL:HIDAYATMASOOD@GMAIL.COM––––––––––––––––––––––––––––––––PICK UP TRUCK, SUBURBANCONTACT: BOONE RACING ENT.PHONE: 301-898-9195, 301-471-9634EMAIL:CRBOONE411@AOL.COM––––––––––––––––––––––––––––––––2006 JCB 3CX BACKHOE • IN GOODCONDITIONCONTACT: AFOLABI JIBRILLPHONE: +233 24 678 8504FAX: +233 30 321 5630EMAIL:AFOLABIJB@YAHOO.COM––––––––––––––––––––––––––––––––HYDRAULIC THUMB TO FIT 1999 EX 160HITACHI EXCAVATOR WITH ALL PIPING& CONTROLS, ALSO QUICK COUPLERHYDRAULIC OR MANUAL. UPPER MID-WEST, SEND PICTURES AND BESTPRICECONTACT: DOUG GYSBERSPHONE: 507-291-0178FAX: 507-263-4106EMAIL:SHERDOUG@FRONTIERNET.NET––––––––––––––––––––––––––––––––KOMATSU / HITACHI 200 SIZE EXCAVA-TOR • MID 90S MACHINE, EAST COASTLOCATIONCONTACT: RICHARDPHONE: 603-828-6100EMAIL: CMIEQUIP@YAHOO.COM––––––––––––––––––––––––––––––––USED CAT 928 AND 930 MODEL 1999AND 2000 • LOOKING TO BUY USEDCAT MODEL 1999 AND 2000 WITHGOOD CONDITIONING, LOOKING FOR 3CAT WHEEL LOADERS, 930 AND 928CONTACT: MAMDOUHPHONE: 509-328-9733EMAIL: MAMDOUHMZAYED@HOTMAIL.COM––––––––––––––––––––––––––––––––
CRANECONTACT: RAFEEC KOTTIKKULONPHONE: 0096597298681EMAIL:RAFEEC@ONGKUWAIT.COM––––––––––––––––––––––––––––––––USED RUBBLE MASTER RM 60 OR 80CRUSHER.CONTACT: BARUN SHARMAEMAIL: SHARMABARUN@GMAIL.COM––––––––––––––––––––––––––––––––WHEEL LOADER 966D, 966E, 936E •WANT TO BUY WHEEL LOADERS LIKETHESE MODEL 966D, E 936E 950D.CONTACT: SAUDPHONE: 5623918774FAX: 5623918774EMAIL: HR1.VIP@HOTMAIL.COM––––––––––––––––––––––––––––––––30-40 HP SELF-PROPELLED CONCRETESAWCONTACT: WILLIAM KANAYANPHONE: 909-337-5428FAX: 909-337-4894EMAIL:WK@KANAYANCONST.COM––––––––––––––––––––––––––––––––MIGHTY MURCH RAM HEAD PART#MM10642 • LOOKING FOR A REPLACE-MENT PART FOR A MIGHTY MURCWOOD SPILTTER MODEL # MM10642RAM HEAD ORIGINAL PURCHASE DATE1994CONTACT: JILLPHONE: 1-256-431-4143EMAIL: JILLDONFRANCISCO@YAHOO.COM––––––––––––––––––––––––––––––––GENERATOR WHISPER WATT • LOOK-ING FOR A WHISPER WATT WITH 20 KWSINGLE PHRASE OR SINGLE & 3PHRASECONTACT: RUSSPHONE: 1-925-449-1958EMAIL: POKY52@AOL.COM––––––––––––––––––––––––––––––––GEHL 7810 E |CONTACT: ALANPHONE: 785-293-2110EMAIL: ROCKCHALKPETERSON@GMAIL.COM––––––––––––––––––––––––––––––––CHIPPERCONTACT: CARLOS SIERRAPHONE: 787-479-2300EMAIL: SIERRACARLOS@YAHOO.COM––––––––––––––––––––––––––––––––JOHN DEERE 690 EXCAVATOR • BUCK-ET TEETHCONTACT: MATTHEW FOERSTERPHONE: 972-437-5137EMAIL:MATTHEWFOERSTER@GMAIL.COM––––––––––––––––––––––––––––––––HOOK LIFT TRUCK 33, 000 GVW •INTERNATIONAL OR SIMILAR 33,000GVW 2002 OR NEWERCONTACT: TOM FLINTPHONE: 201-207-1041FAX: 201-754-9752EMAIL:TOM@THOMASFLINT.COM––––––––––––––––––––––––––––––––ASPHALT ZIPPER | WTB ASPHALT ZIP-PER ANY SIZE NO DEALERS PLEASECONTACT: JAMES MANNPHONE: 404-273-9424FAX: 770-306-2962 |EMAIL:JAMES2525@MSN.COM––––––––––––––––––––––––––––––––
Attention Contractors!Post Your Wanted To Buy Listings FREE!
Here’s How! List Your Wanted ItemsIf you would like to place your Wanted To Buy listings on our website
for inclusion in our newsletters, simply visit: www.ConstructionEquipmentGuide.com/wanted and enter your listings.
Page 40 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
ALEX LYON & SON
AUCTIONEERS
www.lyonauction.com
315-633-2944�
• Kissimmee, FL
Sat.-Sun.,�February�2-10,
2013
For:�Annual�9�Day�Auction!
Construction�Equipment,
Trucks,�Trailers,�Support
• Iowa City, IA
Wed.,�March�13,�2013
For:�Construction
Equipment,�Attachments,
Trucks�and�Trailers
• Las Vegas, NV
Sat.,�March�16,�2013
For:�Late�Model�Rental
Fleet�Equipment
• Atlantic City, NJ
Thurs.-Sun.,�March�21-24,
2013
For:�Construction
Equipment,�Trucks�and
Trailers
• Adams Center, NY
Sat.,�May�4,�2013
For:�Construction
Equipment�300+�Collectible
Cars,�1940-1970,�US�Army
Jeeps�and�More
RITCHIE BROS.
AUCTIONEERS
www.rbauction.com
402-421-2631
• Phoenix, AZFebruary�12-13,�2013
• Tipton, CAFebruary�15,�2013
• Orlando, FLFebruary�18-23,�2013
• Chehalis, WAMarch�5,�2013
• Fort Worth, TXMarch�5-6,�2013
• Salt Lake City, UTMarch�8,�2013
• Denver, COMarch�12,�2013
• Columbus, OHMarch�14,�2013
• Los Angeles, CAMarch�19,�2013
• Northeast, MDMarch�19,�2013
• Raleigh-Durham, NCMarch�21,�2013
• Sacramento, CAMarch�22,�2013
• Nashville, TNMarch�27,�2013
• Atlanta, GAMarch�28,�2013
• Williamsport, PAApril�10,�2013
• Pittsburgh, PAApril�11,�2013
BAR NONE AUCTION
www.barnoneauction.com
866-372-1700�
• San Bernardino, CASat.,�February�23,�2013For:�ConstructionEquipment
• Sacramento, CASat.,�March�9,�2013For:�ConstructionEquipment
• Sacramento, CASat.,�March�23,�2013For:�ConstructionEquipment
DEANCO AUCTIONSwww.deancoauction.com601-656-9768
• Philadelphia, MSMarch�20-22,�2013For:�12th Annual�SpringtimeContractors�EquipmentAuction
• Philadelphia, MSMay�29-30,�2013For:�ConstructionEquipment
• Philadelphia, MSJuly�17-18�2013For:�ConstructionEquipment
• Philadelphia, MSSeptember�18-19,�2013For:�ConstructionEquipment
• Philadelphia, MSNovember�20-21,�2013For:�ConstructionEquipment
DEL PETERSON & ASSO-CIATESwww.delpeterson.com�800-492-9090
• Online OnlyThurs.,�February�19,�2013For:�Construction�and�FarmEquipment,�Trucks�andTrailers
DON SMOCK AUCTION CO., INC.www.dsa-auctions.com765-778-9277
• Pendleton, INMarch�29,�2013For:�ConstructionEquipment
• Pendleton, INJune�21,�2013For:�ConstructionEquipment
• Pendleton, INSeptember�20,�2013For:�ConstructionEquipment
• Pendleton, INDecember�13,�2013For:�ConstructionEquipment
GLOBAL FORCE AUCTION GROUPwww.gforceauction.com�877-631-0650
• Online OnlyFebruary�26-27,�2013For:�ConstructionEquipment
• West Friendship, MD
Sat.,�March�2,�2013
For:�Part�2�of�Liquidation�of
New�River�Landscapes�and
Local�Contractors
HESS AUCTIONEERS
www.hessauctioneers.net
�866-511-2493
• Marietta, PA
Fri.,�February�22,�2013
For:�Construction
Equipment,�Trucks�and
Trailers
HILCO INDUSTRIAL, LLC
www.hilcoind.com
�847-313-4747
• Tuscaloosa, AL
March�20-21,�2013
For:�Construction
Equipment
HUNYADY AUCTION COM-
PANY
www.hunyady.com
�800-233-6898
• Laflin, PA
Wed.,�March,�13�2013
For:�Construction
Equipment,�Trucks�and
Attachments
IRON PLANET AUCTIONS
www.ironplanet.com
�888-433-5426
ONLINE�AUCTIONS
Go�to�www.ironplanet.com
to view the complete auc-
tion schedules, inspection
reports and to place your
bid!
• ONLINE ONLY
February�26-28,�2013
For:�Construction
Equipment
NUTT AUCTION
COMPANY
www.nuttauction.com
903-748-4400
• Garland City, AR
Sat.,�February�16,�2013
For:�Annual�Garland�City
Spring�Equipment�Auction
MYRON BOWLING
AUCTIONEERS, INC.
www.myronbowling.com
�513-738-3311
• Tuscaloosa, ALWed./Thurs.,�March�20-21,2013For:�Well�MaintainedHighway�ConstructionEquipment
PETROWSKY
AUCTIONEERS INC.
www.petrowskyauction-
eers.com
�860-642-4200
• North Franklin, CTThurs.-Sat.,�March�21-23,2013For:�ConstructionEquipment
PURPLE WAVE AUCTION
www.purplewave.com
�866-608-9283
• ONLINE ONLYThurs.,�February�14,�2013For:�ConstructionEquipment
QUANTOS AUCTIONS
www.quantosauctions.com
253-236-8555
• ONLINE ONLYMarch�13,,�2013For:�ConstructionEquipment
UTILITY AUCTIONS
www.utilityauctions.net
�302-530-9103
• Wilmington, DEFri.,�February�22,�2013For:�Construction and UtilityEquipment
WESTERN CONSTRUC-
TION AUCTIONS INC.
www.wca-online.com
�760-731-7760
• Perris, CAThurs.,�February�14,�2013For:�ConstructionEquipment�and�Trucks
YODER & FREY
AUCTIONEERS, INC.
www.yoderandfrey.com
�419-865-3990
• Kissimmee, FLFebruary�11-18,�2013For:�ConstructionEquipment,�Trucks�andTrailers
AuctionsComing
YOUR SOURCE FOR
MONTHLYPUBLICAUCTIONS
Consign With Us! We are always accepting quality consignments. Call us to find out more!
BAR NONE
Heavy Equipment & Commercial Trucks
www.barnoneauction.com (866) 372-1700
featured inventory
Bid Live Onsite or Online! www.barnoneauction.com
SEE COMPLETE INVENTORY AT...
WWW.BARNONEAUCTION.COM
MAR
23FEB
Sacramento, CA4751 Power Inn Road
(916) 383-2000
San Bernardino, CA175 West Central Ave.
(909) 383-5500
23MAR
9
Sacramento, CA4751 Power Inn Road
(916) 383-2000
Heavy Equipment & Commercial Trucks
BAR NONEwww.barnoneauction.com
FEB
23
Heavy Equipment & Commercial Trucks
BAR NONEwww.barnoneauction.com
9MAR
Heavy Equipment & Commercial Trucks
372-1700)866(
23MAR
YLLYTHNOMYOUR SOURCE FOR
23
(909) 383-5500175 West Central Ave.San Bernardino, CA
featured inventory
9
(916) 383-20004751 Power Inn Road
Sacramento, CA
featured inventory
23
(916) 383-20004751 Power Inn Road
Sacramento, CA
us to find out more!quality consignments. Call We are always accepting
Consign With Us!
SNOITCUACPUBLI
www.barnoneauction.comBid Live Onsite or Online!
quality consignments. Call We are always accepting
www.barnoneauction.com
WWW.BARNONEAUCTION.COM
SEE COMPLETE INVENTORY AT...
WWW.BARNONEAUCTION.COM
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 41
California Auction Company Bond #70259785. Preliminary list to date. Equipment subject to change. Copyright © 1999-2012 IronPlanet, Inc. All Rights Reserved. IronPlanet®, IronClad Assurance® and Auctions you can trust® are registered service marks of IronPlanet, Inc. All other marks and brands are the property of their respective owners.
2009 CAT 950H
2012 CAT 120M2
2007 CAT TL943
1998 CAT IT28G
2008 LEEBOY 685
2011 CAT D6T LGP
2007 CAT CS-433E
(4) CAT 740
2008 CAT 963D
2010 CAT 336DL
2002 PETERBILT 379
(3) VOLVO A40D
2007 VOLVO A25D
2010 CAT 928HZ
1999 CAT AP-1055B
REX MODEL S CONCRETE PLANT
100% Online
nline% Online l e
ing equipment frtureaF
oming equipment fr
120M2T2012 CA AT
LGP D6TT1 CA AT201
336DLT2010 CA AT
336DL 2010 CA
928HZT CA AT
950HT2009 CA AT
6852008 LEEBOY Y 685
963DT2008 CA AT
963D VOL2007
VO A25DVOLLVO A25D
TL943TCAT2007
CS-433ET2007 CA AT
379T2002 PETERBIL L
379 CA1999
AP-1055BTAAT
. P58795207d #noy Bnapmon Coitcua AinrofilaCrn tau cos ynoitcud Ana
IT28GT1998 CA AT
IRONPL
egnaho ct tcejbut snempiuq. Eetao dt tsiy lranimiler. Ptsu ® cn, ItenalPnorf Is okrae mcivred seretsigee rr a
740T(4) CA AT
.WWW
. 27-28FEB
OM
s Rthgil Rl. Acn, ItenalPnor2 I102-999t © 1hgirypo. Ceehf ty otrepore phe trs adnard bns akrar mehtl ol. A
VO A40DVOLV (3)
C.TANEIRONPL
. 27-28
tenalPnor. Idevreses R ® ecnarussd AalCnor, I ®
.srenwe ovitcepser ri
VO A40D S CONCRETE PLANTREX MODEL
S CONCRETE PLANT
Page 42 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
Ore. Commission OKs $142MMore for Highway Project
Construction on the improvements washalted in 2010 after unstable soils renderedthree partially completed bridges and onefinished span unsafe.
The TransportationDepartment eventually obtaineda $15 million settlement from acontractor.
The unstable bridges weredemolished and work began onmeasures to reduce landslide risk.
The additional money will gofor landslide mitigation, slopestabilization and construction,highways spokesman Rick Littlesaid in a statement.
He told the Corvallis Gazette-Times the completion date couldbe pushed back again if necessaryto do the job properly.
The transportation commissioners would“rather have a successful project than a quickproject,” he said.
The Transportation Department plans toimmediately spend more than $1 million ofthe new money to partially straighten a curve
at the east end of the project near Eddyville.It was the site of a double-fatal crash inOctober.
The Transportation Commission, whichsets state transportation policy, recently lis-
tened to five options for the U.S. 20 project,including one that would have scrapped it.
“The commission chose an option thatminimizes the cost to complete the projectwhile reducing the geotechnical risks,” Littlesaid.
“The commission chose an option that minimizesthe cost to complete the project while reducing the geoethnical risks.”
Rick LittleOregon Transportation Commission
COMMISSION from page 1
PUBLIC AUCTION: ONSITE & ONLINE
MARCH 201324th Annual Spring Sale
CONSIGN NOW BY CALLING OUR SALES TEAM TODAY!
HEAVY EQUIPMENT & TRUCKS | CONSTRUCTION | INDUSTRIAL | COMMERCIAL | FLEETACCEPTING CONSIGNMENTS NOW!
TN FIRM #2048
FOR LIVE UPDATES VISIT: ritchasonauctioneers.com7538 LINWOOD ROAD | LEBANON, TN 37090 | 800.806.3395 | 615.444.5464
Ritchason Auctioneers, inc.Turning Machinery Into Money Since 1989.
#BidNow #BidLive #BidRitchason via #RAlive
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 43
Page 44 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
Crews Work Five Ten-Hour Days to Complete Renovationssuch as the new Batter’s Eye Club in center-field, which features seating for 100 behindtwo-way glass. The 6,250-sq.-ft. (580 sq m)climate-controlled club has its own buffet,bar, dining area and rest rooms.Other upgrades in 2011 included the
brand-new 12,000 sq. ft. (1,115 sq m)Vandergriff Plaza, which features four newfull-service concession stands and a largevideo board mounted on the back of theBatter’s Eye Club to provide viewing of thegame. Aluminum bleacher seats in Outfield
Plaza were replaced by individual ballparkseats. Covered deck areas with open seatingand tables are above the seating areas onboth the left and right field sides of theBatter’s Eye Club. A two-level, 9,152 sq. ft. (850 sq m)
Rangers-themed restaurant/sports bar on thefirst floor of the office building behind theleft-center field seats is open to the publicbefore, during and after home games. “Wehave new state-of-the-art cooking facilitiesso we can provide more diverse, gourmetfood,” Matwick said. In the same area is Kid’s Zone, the 6,470
sq. ft. (601 sq m) interactive play area.Matwick noted that his daughter contributedideas from her classmates for the play zone.The visitors bullpen was reconfigured,
occupying an area that used to be bleacherseating. For the first time, a majority of theseating bowl will have a view into the visi-tors’ bullpen. The concourse leading frombehind section 3 into Vandergriff Plaza waswidened to provide more efficient trafficflow.
Up at BatAnother off-season, another renovation
project. This year the work is going onbehind home plate. “We’re adding seats on the field level and
expanding the dugouts,” Matwick said. A third row of home plate seats will be
added in front of the two existing rows ofpremium seating built for the 2009 season.The 52 new seats will bring the number ofhome plate seats to 148 between the twodugouts. The wider, cushioned seats feature higher
backs and have additional leg room. Anadded bonus is the complementary buffet inthe renovated Capital One Club before everygame and complementary soft drinks andsnacks delivered to all seat holders.Other amenities for the fans include
extensive renovations and upgrades to theprivate club, two major concession standsbehind home plate and two new free-stand-ing concession stands, as well as a new retailstore and concessions stands on the mainconcourse.
Structural work will be done in the centerof the climate-controlled Capital One Club,the private home plate club, to remove sev-eral sections of steel in order to improve theview of the field. New cooking areas, bars and dining room
space will become the focal point of the cen-ter area. Permanent seating will be relocatedand the number of permanent seats will beincreased from 76 to 104. Square footage also will increase — from
8,100 to 9,100 (753 to 845 sq m). The exist-ing entrance to the Capital One Club andseating in Section 126 will be removed, giv-ing fans entering the ballpark through thehome plate gate a wide-open view of theplaying field. The existing concessions
stands on the main concoursebehind home plate will be ren-ovated to create display cook-ing areas, similar to those inVandergriff Plaza. “The six new concession
stands and the club space werea big success last year,”Matwick said, adding that heexpects this year’s modifica-tions to be equally popular.Another addition he hopes
will be popular is a new 2,120sq. ft. (197 sq m) merchandisestore constructed in the spacewhere the west box office cur-rently exists on the main con-course. New concessions stands
will be added on the south end of the newretail store and along the outer wall of themain concourse on the third base side. Theselocations will add points of sale and areexpected to ease congestion along the mainconcourse on the first and third base sides.It’s all about convenience and keeping
fans connected via new technology whenthey’re up out of their seats. “We hope thecrowds are due to the quality of play,”Matwick said, “but for season ticket holders,it’s unrealistic to expect the fans to sit in theirseats for three hours. We brainstormed con-cepts for improvements and to drive rev-enue. There are interesting things to do —lots of options.”
Less Is MoreThe addition of the new home plate seats
and permanent seats in the Capital OneClub, along with the removal of seats inSection 126 as part of the renovation on themain concourse behind home plate and sev-eral other adjustments, will change the seat-ing capacity of the ballpark from 48,194 to48,114. While not exactly comparable, it does fol-
low the current trend of smaller, more inti-
mate facilities that are decidedly not multi-purpose. “For the past 20 years we’ve seentraditional, old-school design,” Matwicksaid. These new ballparks are typically locat-ed downtown, integrated into the city sky-line. One thing that never shrinks is the budget.
Funding of the $35 million three-year reno-vation comes from the ownership. “They know it’s needed and has the
potential for return,” Matwick said.Concessionaire and the ballpark’s food andbeverage partner, Delaware NorthSportservice, also is a partner in funding. “The Rangers are committed to providing
an outstanding experience for our fans when
they come to Rangers Ballpark inArlington,” said CEO and President NolanRyan. He added that they plan to continue“undertaking significant renovation andupgrade projects to help achieve that goal …over the next several years.”The next target area has already been
identified: left field. The architects of recordfor the project are Sterling Barnett Little ofArlington and Populous of Kansas City.They are currently studying plans, Matwicksaid, and during the first quarter of 2013, heanticipates discussion about the work to bedone. Plans for “Year 5” have not been deter-mined yet.
Running the BasesBut first, “Year 3” must be completed. In
fact, the upgrades must be completed byopening day: Friday, April 5, 2013. “We have a lot of work to do in a short
amount of time,” said Justin Wade, projectmanager of General Contractor ManhattanConstruction. The Tulsa, Okla.-based firmbuilt Rangers Ballpark in Arlington, andcompleted the ballpark renovations last win-ter. “It’s a tight schedule and a tight budget.”All demolition work is done. “We
demo’ed the existing concessions on themain concourse,” Wade said. That was done to make way for a bigger
concession along the outer stadium wall.The old Cuervo Club above the main con-course was gutted for renovation. The oldticket office on the west side will become aconcession kiosk and retail area. Crews alsomade alterations to the back wall behindhome plate and the dugout floor.Forms for the concrete work on the bowl
level were placed in November, with thepours scheduled before the end of thatmonth. Once that cures, crews will startworking on dry wall and steel — as soon asmaterials arrive.
Wade was nervously waiting onmaterials to show up in mid-November. “We’re having troublegetting the materials when we needthem.” Knowing that “time is a bigdeal” on this project, he said crewshave been working a “5 x 10”schedule (five ten-hour days), plus8 hours on Saturday, but said they“may go into multiple shifts whenthe materials show up.”When the steel arrived, it had to
be brought through the 8 ft. (2.4 m)wide gate on warehouse forkliftsbecause of the narrow entry. “Thesteel guys have to manhandle it,”Wade said. They may be manhandling
materials, but the crews have totreat the job site gently. “We’re working over a tunnel in
a garage, so no heavy equipment can beused,” Wade said. Instead, they’re movingmaterials by skid steers with hoppers.Because they also have to stay off the field,they put plywood down and try to stay alongthe foul line. “They’re still using the fieldwhen we’re not working.”Special events for non-game-days are part
of the marketing plan, according toMatwick. It’s one reason they opted toenhance the HVAC system for year-rounduse. “We rent the facility for meetings, fanfests and weddings.” In addition to updatingthe HVAC system, he said plans call forimproving the mechanical, electrical andplumbing systems.As Wade said, it’s a lot of work in a short
time. With “subs for everything,” coordina-tion and communication are keys to on-timecompletion. “It’s a difficult project,” he said.“Not only do I have to communicate witheveryone, I have to make sure everyonecommunicates with each other.” Fortunately,he adds, “I like a challenge.”
(This story also can be found onConstruction Equipment Guide’s Web site atwww.constructionequipmentguide.com.)CEG
RANGERS from page 1
It’s all about convenience and keeping fans connected via newtechnology when they’re up out of their seats.
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 45
CAT AUCTION SERVICES860 Blue Gentian Road, Suite 100 Eagan, MN 55121
855.228.2286 info@catauctions.com
Follow the new leader.®
www.catauctions.com
Equipment subject to change. View updated equipment lists at www.catauctions.com
2005 CAT 980H MARCH 27
2001 CAT 320CL APRIL 4
2008 CAT D8T MARCH 27
2000 CAT 623F APRIL 4
©2013 Caterpillar. All Rights Reserved. CAT, CATERPILLAR, their respective logos and “Caterpillar Yellow,” as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
AUCTIONSUPCOMINGFOLLOW THE NEW LEADER TO OUR
KANSAS CITY MARCH 279am Central Time Hosted by: Foley Equipment 5701 E. 87th Street, Kansas City, MO 64132
DENVER, CO APRIL 49am Mountain Time Hosted by: Wagner Equipment 18000 Smith Road, Aurora, CO 80011
UNRESERVED PUBLIC AUCTIONS
www.catauctions.com
Our auctions offer a wide variety of equipment makes and models, as well as premium services from the Cat name you already know and trust. Search the full equipment listing and register to bid online at:
ONLINEBIDDINGAVAILABLE!
EH TWOLLOF
TREDAELWNEE
UR OO T
ER
l
SERNU
arent Cma9
ASANK
L
d b
BU PDEVER
etsoHemi T
YTICSA
ON
p
ITCU ACIL
uiq EeyloF: yd b
CHRAMY
S
t
ON
nem
7 2CH
h S
atnuo Mma9
EVEND
t7. 81 E075
, M
etsoHemi Tnia
OC,RE
ytis CasnaK, teerth S
2
EqurengaW: yd be
4LIRAP
314O 6, M
tnempi Equ
4
Search the full equipment listing and register to bid online at:
h R
well as premium services from the Cat name you already know and trust. Our auctions offer a wide variety of equipment makes and models, as
.catauctions.comwww
tim0 S0081atnuo Mma9
Search the full equipment listing and register to bid online at:
O 8
well as premium services from the Cat name you already know and trust. Our auctions offer a wide variety of equipment makes and models, as
.catauctions.com
, Caroru, Adaoh RetsoHemi Tnia
Search the full equipment listing and register to bid online at:
1
well as premium services from the Cat name you already know and trust. Our auctions offer a wide variety of equipment makes and models, as
.catauctions.com
100 EqurengaW: yd be
t
well as premium services from the Cat name you already know and trust.
.catauctions.com
nempi Equ
INELNO
.catauctions.comwwwFollow the new leader
are trademarks of Caterpillar and may not be used without permission., CTT, CA. All Rights Reserved. CA T©2013 Caterpillar
.catauctions.comwww
.catauctions.comFollow the new leader
are trademarks of Caterpillar and may not be used without permission.ellowTERPILLAR, their respective logos and “Caterpillar Y CA T
.catauctions.com
860 Blue Gentian Road, Suite 100 855.228.2286
®.
,” as well as corporate and product identity used herein, ellow
.catauctions.com
860 Blue Gentian Road, Suite 100 TION SERVICUAT CAAT
855.228.2286
Eagan, MN info@catauctions.com
E!LABLAIVVAIAINGDDIBINELNO.catauctions.com
SECTION SERVI Eagan, MN 55121
info@catauctions.com
wwwequipment lists atquipment subject to change. E
.catauctions.comwwwiew updated Vquipment subject to change.
Page 46 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE
ADVERTISER INDEX
The Advertisers Index is printed as a free editorial service to our advertisers and readership. Construction Equipment Guide is not responsible for errors or omissions.
ALLU GROUP.................................................................11
BAR NONE AUCTION
SAN BERNARDINO CA .........................................40
CAT AUCTION SERVICES
KANSAS CITY MO .................................................45
CEG SCALE MODELS ..................................................10
CLASSIFIEDS ................................................................35
CONSTRUCTION EQUIPMENT COMPANY ...............19
CONSTRUCTION EQUIPMENT GUIDE
WANTED.................................................................39
AUCTION TRIPLE PLAY........................................43
EXCAVATOR & ATTACHMENTS PROMO............22
DARR EQUIPMENT CO ................................................11
DOOSAN INFRACORE AMERICA CORP ....................30
DOOSAN PORTABLE POWER.....................................32
DYNAPAC.......................................................................35
ESCO CORP..................................................................34
EXODUS....................................................................16,17
FELLING TRAILERS......................................................37
FINN................................................................................15
FLANGE LOCK ................................................................2
FLECO ATTACHMENTS................................................29
FLUID CONTROL SERVICES.........................................6
GRINDERCRUSHERSCREEN.COM............................14
GROVE CRANE.............................................................47
HELAC CORPORATION................................................29
HENDRIX MACHINERY LLC...........................................3
HYDRAULICIRCUIT TECHNOLOGY............................28
IROCK CRUSHERS.......................................................14
IRON PLANET................................................................41
KAWASAKI CONSTRUCTION MACHINERY ...............33
KIRBY-SMITH MACHINERY INC ..................................48
KOMATSU AMERICA CORP....................................30,31
KPI-JCI............................................................................20
LBX ............................................................................24,25
MACDONALD EQUIPMENT CO.....................................5
METSO MINERAL SCREENING...................................20
METSO MINERALS .......................................................15
MIDCO DEMOLITION TOOL CO ..................................18
NATIONAL ATTACHMENTS ..........................................28
NATIONAL EQUIPMENT REGISTER .............................6
NORAM ..........................................................................23
RECS-BAYONET BREAKER.........................................29
RITCHASON AUCTIONEERS
LEBANON TN.........................................................42
ROAD BUILDERS MACHINERY..................................6,9
ROAD MACHINERY CO..................................................7
SENNEBOGEN ..............................................................21
SUPERIOR INDUSTRIES..............................................18
TOM GROWNEY EQUIPMENT INC ...............................2
TOWMASTER ................................................................38
VAUGHAN AUCTION GROUP LLC
WILLS POINT TX....................................................42
CONSTRUCTION EQUIPMENT GUIDE • www.constructionequipmentguide.com • February 9, 2013 • Page 47
Belgrade, MT406-388-2308Billings, MT
406-259-9720Boise, ID
208-388-3323Salt Lake City, UT801-974-0388
St. George, UT435-674-2994Las Vegas, NV702-320-6500Phoenix, AZ
602-232-0600Tucson, AZ
520-770-1120
Albuquerque, NM505-764-8100
Dallas, TX972-986-0910Houston, TX
713-433-6411
range in capacity from 8t to 450t (8.5 USt to 550 USt)
Grove cranes
Built to performGrove mobile telescopic cranes
Contact your dealer or visit www.manitowoc.com/cranesdealer
Built to per
Built to per
rmofBuilt to per
e all-terrain, rvorGd-worhar
challenging lifting jobs with str
ur cranes o�er the vOranging fr
ovGr
ough-terrain and tre all-terrain, rformance featurigh perking. Hd-wor
ength, prchallenging lifting jobs with str
ersatility to tackle any prur cranes o�er the vt to 50t (8.5 US5om 8t to 4ranging fr
e mobile telescopic cranesov
e long-lasting and uck cranes arough-terrain and tren the most ecute eves help exformance featurol. ecision and contrength, pr
oject, with capacities ersatility to tackle any prt).0 US5t to 5
e mobile telescopic cranes
e long-lasting and en the most
oject, with capacities
ranging fr
t to 50t (8.5 US5om 8t to 4ranging fr
t).0 US5t to 5
Gr
( fr
Contact your dealer or visit www
r
H&E Equipment Serviceswww.HE-equipment.com
8600 Calabash Ave.Fontana, CA 92335562-286-6618
Fax: 909-356-1340275 W. Larch RoadTracy, CA 95304209-597-3824
5909 12th Street EastFife, WA 98424253-254-7950
5801 Silverado WayAnchorage, AK 99518
855-342-726391-210 Kalaeloa Blve.Kapolei, HI 96707808-682-7263
Western Pacific Crane & Equipmentwww.wpcrane.com
Kirby-Smith Machinery, Inc.www.kirby-smith.com
Oklahoma City, OK800-375-3339
Tulsa, OK800-375-3733Kansas City, KS877-851-5729St. Louis, MO
866-279-1392
Page 48 • February 9, 2013 • www.constructionequipmentguide.com • CONSTRUCTION EQUIPMENT GUIDE