Post on 10-Oct-2018
FiberstoreOS
Basic Command Line Reference
Contents
1 System Configuration Commands..............................................................................................51.1 hostname....................................................................................................................................51.2 management ip address............................................................................................................51.3 management route.................................................................................................................... 61.4 showmanagement ip address..................................................................................................71.5 enable password........................................................................................................................81.6 terminal length.......................................................................................................................... 81.7 service terminal-length.............................................................................................................91.8 banner motd............................................................................................................................ 101.9 banner exec..............................................................................................................................101.10 banner login...........................................................................................................................111.11 show version..........................................................................................................................121.12 line vty maximum..................................................................................................................121.13 exec-timeout..........................................................................................................................131.14 reboot.....................................................................................................................................141.15 schedule reboot at.................................................................................................................141.16 schedule reboot delay...........................................................................................................151.17 boot system............................................................................................................................151.18 show boot...............................................................................................................................161.19 show boot images..................................................................................................................161.20 showmemory........................................................................................................................171.21 show cpu traffic-limit............................................................................................................191.22 show processes cpu sorted.................................................................................................. 201.23 show processes cpu history................................................................................................. 211.24 show processes memory sorted..........................................................................................221.25 terminal monitor...................................................................................................................241.26 configure terminal.................................................................................................................241.27 disable....................................................................................................................................251.28 enable.....................................................................................................................................251.29 end..........................................................................................................................................261.30 exit (global)............................................................................................................................271.31 exit (EXEC).............................................................................................................................271.32 quit..........................................................................................................................................281.33 cd............................................................................................................................................ 28
1.34 copy........................................................................................................................................ 291.35 delete......................................................................................................................................301.36 dir........................................................................................................................................... 311.37 ls..............................................................................................................................................321.38 more....................................................................................................................................... 331.39 mkdir......................................................................................................................................331.40 rename................................................................................................................................... 341.41 rmdir...................................................................................................................................... 351.42 tar create................................................................................................................................351.43 tar table..................................................................................................................................361.44 tar xtract.................................................................................................................................371.45 tar diagnostic-information...................................................................................................371.46 format.....................................................................................................................................381.47 umount...................................................................................................................................381.48 umount...................................................................................................................................39
2 User Management Commands................................................................................................. 412.1 username..................................................................................................................................412.2 username password................................................................................................................412.3 username secret...................................................................................................................... 422.4 username privilege..................................................................................................................432.5 username privilege password................................................................................................432.6 re-username newname...........................................................................................................442.7 cipher detect............................................................................................................................44
3 FTP Commands........................................................................................................................... 463.1 ftp..............................................................................................................................................463.2 ftp vrf........................................................................................................................................473.3 ftp username............................................................................................................................473.4 ftp password............................................................................................................................ 483.5 ftp passive................................................................................................................................ 493.6 show ftp....................................................................................................................................49
4 TFTP Commands.........................................................................................................................514.1 copy GFILENAME GURLNAME...............................................................................................514.2 copy GURLNAME GFILENAME...............................................................................................514.3 copy running-config mgmt-if................................................................................................. 524.4 copy startup-config mgmt-if...................................................................................................534.5 copy mgmt-if startup-config...................................................................................................53
5 SCP Commands............................................................................................................................55
5.1 copy GFILENAME GURLNAME...............................................................................................555.2 copy GURLNAME GFILENAME...............................................................................................55
6 Telnet Commands.......................................................................................................................576.1 telnet.........................................................................................................................................57
7 SSH Commands............................................................................................................................597.1 ip ssh server.............................................................................................................................597.2 ip ssh server authentication-retries......................................................................................597.3 ip ssh server authentication-timeout....................................................................................607.4 ip ssh server authentication-type..........................................................................................617.5 ip ssh server host-key rsa key................................................................................................617.6 ip ssh server rekey-interval....................................................................................................627.7 ip ssh server version............................................................................................................... 627.8 show ip ssh server session..................................................................................................... 637.9 show ip ssh server status........................................................................................................647.10 rsa key generate.................................................................................................................... 647.11 rsa key.................................................................................................................................... 657.12 key format..............................................................................................................................657.13 key string end........................................................................................................................667.14 key type..................................................................................................................................667.15 reset........................................................................................................................................677.16 validate...................................................................................................................................687.17 KEYLINE.................................................................................................................................687.18 rsa key export........................................................................................................................697.19 rsa key import....................................................................................................................... 697.20 show rsa key..........................................................................................................................707.21 show rsa keys........................................................................................................................ 717.22 ssh...........................................................................................................................................72
8 Time&Timezone......................................................................................................................... 748.1 clock set datetime....................................................................................................................748.2 clock set timezone...................................................................................................................748.3 clock set summer-time............................................................................................................758.4 show clock................................................................................................................................768.5 show timezones.......................................................................................................................77
9 License Commands.....................................................................................................................799.1 generate device identifier.......................................................................................................799.2 show license.............................................................................................................................79
5
1 System Configuration Commands
1.1 hostnameTo specify or modify the host name for the network server, use the hostname commandin global configuration mode. To restore the configuration to the default, use no form ofthis command.
Command Syntaxhostname nameno hostname
name New host name for the network server
Command ModeGlobal Configuration
DefaultThe default host name is Switch.
UsageThe host name is used in prompts and default configuration filenames.The name must also follow the rules for ARPANET host names. They must start with aletter, and have as interior characters only letters, digits, hyphens, and underline. Namesmust be 63 characters or fewer.
ExamplesThe following example changes the host name to “sandbox”:Switch(config)# hostname sandboxsandbox(config)#
Related CommandsNone
1.2 management ip addressUse this command to set the management IP address on the Switch.To remove the management IP address, use the no form of this command.
Command Syntaxmanagement ip address (A.B.C.D/M |A.B.C.D mask) (gateway A.B.C.D)
6
no management ip addressmanagement ipv6 address (X:X::X:X/M | X:X::X:X mask) (gateway X:X::X:X)no management ipv6 address
A.B.C.D/M The management IPv4 address with mask length configured
A.B.C.D mask The management IPv4 address and mask configured
X:X::X:X/M The management IPv6 address with mask length configured
X:X::X:X mask The management IPv6 address and mask configured
gateway Add gateway
Command ModeGlobal Configuration
DefaultNone
UsageNone
ExamplesThe following example sets the management ipv4 address.Switch(config)# management ip address 192.168.100.100/24The following example unsets the management ipv4 address.Switch(config)# no management ip addressThe following example sets the management ipv6 address.Switch(config)# management ipv6 address 2001:1000::1000/96The following example unsets the management ipv6 address.Switch(config)# no management ipv6 address
Related CommandsNone
1.3 management routeUse this command to set the gateway on the Switch for management ip.
Command Syntaxmanagement route (add | del ) gateway A.B.C.Dmanagement ipv6 route (add | del )gateway X:X::X:X
add Add the route
7
del Del the route
ipv6 Configure IPv6 gateway
gateway Add gateway
A.B.C.D The IPv4 address of the gateway
X:X::X:X The IPv6 address of the gateway
Command ModeGlobal Configuration
DefaultNone
UsageNone
ExamplesThe following example sets the gateway of 192.168.100.254 for the switch.Switch(config)# management route add gateway 192.168.100.254The following example sets the gateway of 2001:1000::1 for the switch.Switch(config)# management ipv6 route add gateway 2001:1000::1
Related CommandsNone
1.4 showmanagement ip addressCommand Syntax
showmanagement ip addressshowmanagement ipv6 address
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesSwitch# show management ip addressManagement IP address is: 192.168.100.100/24
Gateway: 192.168.100.254
Switch# show management ipv6 addressManagement IPv6 address is: 2001:1000::1000/96
Gateway: 2001:1000::1
8
Related CommandsNone
1.5 enable passwordUse this command to set the password which is needed when user enter Privileged EXECmode.
Command Syntaxenable password ( privilege LEVEL| ) ( 8| ) LINEno enable password
Privilege LEVEL User privilege level, Level value <1-4>
8 Specifies a hidden password will follow
LINE The 'enable' password string
Command ModeGlobal Configuration
DefaultNone
UsageIf this command is set, user need to provide the password when enter Privileged EXECmode.
ExamplesThe following example shows how to set the password.Switch(config)# enable password 123Switch(config)# exitSwitch# disableSwitch> enablePassword:
Switch#
Related CommandsNone
1.6 terminal lengthTo set the number of lines on the current terminal screen for the current session, use theterminal length command in EXEC mode. To restore the configuration to the default, usethe no form of this command.
Command Syntaxterminal length screen-lengthterminal no length
9
screen-length Number of lines on the screen. The value is a number from 0 to512. A value of zero disables pausing between screens of output
Command ModePrivileged EXEC
DefaultAutomatically detected by terminal screen length
UsageThe system uses the length value to determine when to pause during multiple-screenoutput. A value of zero prevents the switch from pausing between screens of output.Some types of terminal sessions do not require you to specify the screen length becausethe screen length specified can be learned by some remote hosts. For example, the rloginprotocol uses the screen length to set up terminal parameters on a remote UNIX host.
ExamplesIn the following example, the system is configured to prevent output from pausing if itexceeds the length of the screen:Switch# terminal length 0
Related Commandsservice terminal-length
1.7 service terminal-lengthTo set the number of lines on the current terminal screen for all sessions, use the serviceterminal-length command in global configuration mode. To restore the configuration tothe default, use the no form of this command.
Command Syntaxservice terminal-length screen-lengthno service terminal-length
screen-length Number of lines on the screen. The value is a number from 0 to512. A value of zero disables pausing between screens of output
Command ModeGlobal Configuration
DefaultNone
10
UsageThe system uses the length value to determine when to pause during multiple-screenoutput. A value of zero prevents the switch from pausing between screens of output.Some types of terminal sessions do not require you to specify the screen length becausethe screen length specified can be learned by some remote hosts. For example, the rloginprotocol uses the screen length to set up terminal parameters on a remote UNIX host.
ExamplesIn the following example, the system is configured to prevent output from pausing if itexceeds the length of the screen:Switch(config)# service terminal-length 0
Related Commandsterminal length
1.8 banner motdTo set a single or multiline message banner that appears on the screen when someonelogs in to the switch, use the banner motd command in global configuration mode. Torestore the configuration to the default, use the no form of this command.
Command Syntaxbanner motd lineno banner motd
line C banner-text c, where 'c' is a delimiting character
Command ModeGlobal Configuration
DefaultNone
UsageNone
ExamplesThis example shows how to set a single message banner.Switch(config)# banner motd #Enter TEXT message. End with the character '#'.
this is a example message#
Related Commandsbanner execbanner login
1.9 banner execTo set an exec banner to be displayed on all connected terminals and this bannerappears when terminal in Privileged EXEC mode, use the banner motd command in
11
global configuration mode. To restore the configuration to the default, use the no form ofthis command.
Command Syntaxbanner exec lineno banner exec
line C banner-text c, where 'c' is a delimiting character
Command ModeGlobal Configuration
DefaultNone
UsageNone
ExamplesThis example shows how to set a single message banner.Switch(config)# banner exec #Enter TEXT message. End with the character '#'.
this is a example message#
Related Commandsbanner motdbanner login
1.10 banner loginTo set a login banner to be displayed on all connected terminals, and this banner appearsafter the MOTD banner and before the login prompt, use the banner motd command inglobal configuration mode. To restore the configuration to the default, use the no form ofthis command.
Command Syntaxbanner login lineno banner login
line C banner-text c, where 'c' is a delimiting character
Command ModeGlobal Configuration
DefaultNone
12
UsageNone
ExamplesThis example shows how to set a single message banner.Switch(config)# banner login #Enter TEXT message. End with the character '#'.
this is a example message#
Related Commandsbanner execbanner motd
1.11 show versionTo display the version information of the hardware and firmware, use the show versioncommand in EXEC mode.
Command Syntaxshow version (slot id | )
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThis example shows how to display version information of the hardware and firmware.Switch# show version
Related CommandsNone
1.12 line vty maximumTo set the max login VTY, use this command in global configuration mode. To restore theconfiguration to the default, use the no form of this command.
Command Syntaxline vty maximum vty_valueno line vty maximum
vty_value Max login VTY. The default value is 8.range <0-8>
Command ModeGlobal Configuration
13
Default8
UsageNone
ExamplesThis example shows how to set the max VTY to 5.Switch(config)# line vty maximum 5
Related CommandsNone
1.13 exec-timeoutTo set how much time the login user do not do any operation then the user should beforced to quit, use the no form of this command.
Command Syntaxexec-timeoutminutes seconds
no exec-timeout
minutes Range <0-35791>
seconds Range <0-2147483>
Command ModeConfig-line Configuration
Default600 seconds
UsageWhen the user login again then config will be effected.
ExamplesThis example shows how to set max time the login user do not do any operation then theuser should be forced to quit.Switch(config)# line vty 0Swicth(config-line)# exec-timeout 3 200
Related CommandsNone
14
1.14 rebootTo reload the operating system, use the reload command in Privileged EXEC mode.
Command Syntaxreboot
Command ModePrivileged EXEC
DefaultNone
UsageThe reboot command halts the system. Use the reboot command after configurationinformation is entered into a file and saved to the startup configuration.
ExamplesThe following example is sample dialog from the reboot command.Switch# reboot
Related Commandsreload
1.15 schedule reboot atTo schedule a reload of the software to take place at the specified time, use the schedulereboot at command in global configuration mode. To cancel the scheduled reboot task,use the no form of this command.
Command Syntaxschedule reboot at HH:MM (MM/DD | MM/DD/YYYY | YYYY/MM/DD)no schedule reboot
HH:MM The hour and minutes. The time range is 00:00 – 23:59
MM/DD Specify the date for current year (MM/DD format)
MM/DD/YYYY Specify the date (MM/DD/YYYY format, year range is [2000,2037])
YYYY/MM/DD Specify the date (YYYY/MM/DD format, year range is [2000,2037])
Command ModeGlobal Configuration
DefaultNo scheduled reboot task is defined.
UsageIf you specify the month and day, the reload is scheduled to take place at the specifiedtime and date. If you do not specify the month and day, the reload takes place at thespecified time on the current day.
15
ExamplesThe following example is sample dialog from the schedule reboot at command.Switch(config)# schedule reboot at 12:12 2008/12/25
Related Commandsschedule reboot delay
1.16 schedule reboot delayTo schedule a reload of the software to take place after the specified time, use theschedule reboot delay command in global configuration mode. To cancel the scheduledreboot task, use the no form of this command.
Command Syntaxschedule reboot delay {HH:MM |minutes}no schedule reboot
HH:MM The hour and minutes. The time range is 00:00 – 23:59
minutes The minutes. The range is 1 – 720
Command ModeGlobal Configuration
DefaultNo scheduled reboot task is defined.
UsageNone
ExamplesThe following example is sample dialog from the schedule reboot delay command.Switch(config)# schedule reboot delay 300
Related Commandsschedule reboot at
1.17 boot systemTo specify the system image that the switch loads at startup, use the following bootsystem commands in Privileged EXEC mode.
Command Syntaxboot system (tftp: mgmt-if SERVERIP | flash:/) file-name
flash System image file for next booting
tftp System image file for next booting
mgmt-if Management port
SERVERIP The tftp server ip
16
file-name The file name that will be used to load at startup
Command ModePrivileged EXEC
DefaultNone
UsageManagement IP address in startup-config file will be used as source address whensystem boot via TFTP.
ExamplesThe following example is sample dialog from the boot system command.Switch# boot system flash:/boot/Internal-1.0.0.25.bin
Related Commandsshow boot
1.18 show bootTo display the current image and the image the next startup will load, use the show bootcommand in Privileged EXEC mode.
Command Syntaxshow boot
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThe following is sample output from the show boot command.Switch# show bootThe current boot image version is: E330-3.0.0.23.it
The current running image is: tftp://10.10.29.160/humberOS-e330-ma-v3.0.0.23.it.r.bin
The next running image is: tftp://10.10.29.160/humberOS-e330-ma-v3.0.0.23.it.r.bin
Related Commandsshow boot images
1.19 show boot imagesTo display all booting images available in the flash system, use the show boot imagescommand in Privileged EXEC mode.
17
Command Syntaxshow boot images
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThe following is sample output from the show boot images command.Switch# show boot imagesSystem image files list:
Current boot image version: 1.0.0.25
Create Time Version File name
===============================================================
* 2011-07-25 10:58:29 v3.0.0.22.it Internal-3.0.0.22.bin
Related Commandsshow boot
1.20 showmemoryTo display memory utilization information about the active processes, use the showmemory command in Privileged EXEC mode.
Command Syntaxshowmemory (all | bgp | bhm | chsm | dhclient |dot1x | imi | ipv6 | lacp | ldp | lib |mstp | nsm | oamd |onmd| ospf | pim | ptp| rip | rsvp | shal | summary)
all All memory information
bgp Border Gateway Protocol (BGP)
bhm Health monitoring
chsm Chassis management
dhclient DHCP client module
dot1x IEEE 802.1X Port-Based Access Control
imi Integrated Management Interface (IMI)
ipv6 Internet Protocol version 6 (IPv6)
lacp Link Aggregation Control Protocol (LACP)
ldp Label Distribution Protocol (LDP)
lib Library information
mstp Spanning Tree Protocols (STP/RSTP/MSTP)
nsm Network Service Module (NSM)
18
oamd Bidirectional Forwarding Detection (BFD)
onmd LLDP and EFM_OAM
ospf Open Shortest Path First (OSPF)
pim Protocol Independent Multicast (PIM)
ptp Precision Time Protocol (PTP)
rip Routing Information Protocol (RIP)
rsvp Resource Reservation Protocol (RSVP)
shal Hal server monitoring
summary Summary memory information
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThe following is sample output from the show memory command with keyword bgp:Switch# show memory bgpLibrary memories for BGP
Memory type Alloc cells Alloc bytes
============================== ============ ==============
Temporary memory : 6596 322216
Hash : 10 320
Hash index : 10 40960
Hash bucket : 55 880
Link list : 13 400
Link list node : 115 1840
Show : 1 512
Show page : 1 8192
Show server : 1 64
Prefix IPv4 : 6 48
Route table : 6 48
Route node : 309 19776
Vector : 3383 324768
Vector index : 3383 48824
SNMP subtree : 8 6144
Host config : 1 16
Message of The Day : 1 128
IMI Client : 2 1056
VTY master : 1 16
VTY if : 52 39936
VTY connected : 3 192
Message handler : 2 128
Host : 1 96
Log information : 2 128
19
Context : 1 512
Memories for BGP
Memory type Alloc cells Alloc bytes
============================== ============= ===============
BGP structure : 1 768
BGP VR structure : 1 384
BGP global structure : 1 64
BGP peer : 1 2048
Ext community : 1 16
BGP as list master : 1 32
Community list handler : 1 32
BGP Damp Reuse List Array : 1 2048
BGP table : 31 248
BGP VRF list : 1 64
Related Commandsshow processes memory sorted
1.21 show cpu traffic-limitUse this command to show the CPU traffic-limit configurations.
Command Syntaxshow cpu traffic-limit
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThis example shows cpu traffic-limit configurations.Switch # show cpu traffic-limitreason rate (pps) class
bpdu 64 3
cfm 512 2
slow-protocol 128 1
eapol 128 0
erps 128 2
smart-link 128 2
udld 128 3
arp 640 1
dhcp 128 0
rip 64 1
ldp 512 1
ospf 256 1
pim 128 1
20
vrrp 512 1
rsvp 512 1
ipda 1024 0
icmp-redirect 128 0
mcast-rpf-fail 128 1
macsa-mismatch 128 0
port-security-discard 128 0
vlan-security-discard 128 0
mtu-dontfrag 64 0
mtu-frag 64 0
ptp 512 2
ip-option 512 0
ucast-ttl-fail 64 0
mpls-ttl-fail 64 0
igmp 128 2
sflow-ingress 128 0
sflow-egress 128 0
fwd-to-cpu 64 0
mpls-tp-pwoam 128 2
Total rate: 2048 (pps)
Related CommandsNone
1.22 show processes cpu sortedTo display CPU utilization information about the active processes sorted by percentagein a device, use the show processes cpu sorted command in Privileged EXEC mode.
Command Syntaxshow process cpu sorted
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThe following is sample output from the show processes cpu sorted command:Switch# show processes cpu sortedCPU usage for five seconds: 4.17%; one minute: 3.70%; five minutes: 3.68%
PID TIME %CPU TTY COMMAND
924 00:20:03 2.0 ? hsrvd
956 00:07:17 0.7 ? nsm
1007 00:02:44 0.2 ? imi
959 00:01:24 0.1 ? snmpd
1317 00:00:01 0.1 pts/0 imish
5 00:00:45 0.0 ? events/0
983 00:00:23 0.0 ? mstpd
21
985 00:00:15 0.0 ? onmd
966 00:00:15 0.0 ? lacpd
963 00:00:12 0.0 ? bhm
929 00:00:12 0.0 ? chsm
964 00:00:11 0.0 ? oamd
919 00:00:10 0.0 ? ntpd
1003 00:00:08 0.0 ? pimd
942 00:00:08 0.0 ? sshd
957 00:00:08 0.0 ? dhcrelay
973 00:00:07 0.0 ? authd
1005 00:00:07 0.0 ? ldpd
977 00:00:07 0.0 ? rmond
1021 00:00:07 0.0 ? ripd
1027 00:00:07 0.0 ? ospfd
1032 00:00:07 0.0 ? bgpd
1 00:00:05 0.0 ? init
779 00:00:04 0.0 ? jffs2_gcd_mtd1
1106 00:00:01 0.0 ? imish
3 00:00:00 0.0 ? ksoftirqd/0
916 00:00:00 0.0 ? syslog-ng
65 00:00:00 0.0 ? bdi-default
965 00:00:00 0.0 ? ptpd
917 00:00:00 0.0 ? crond
63 00:00:00 0.0 ? sync_supers
1096 00:00:00 0.0 ? telnetd
6 00:00:00 0.0 ? khelper
105 00:00:00 0.0 ? khungtaskd
2 00:00:00 0.0 ? kthreadd
4 00:00:00 0.0 ? watchdog/0
9 00:00:00 0.0 ? netns
10 00:00:00 0.0 ? async/mgr
66 00:00:00 0.0 ? kblockd/0
73 00:00:00 0.0 ? kseriod
88 00:00:00 0.0 ? rpciod/0
106 00:00:00 0.0 ? kswapd0
157 00:00:00 0.0 ? aio/0
164 00:00:00 0.0 ? nfsiod
171 00:00:00 0.0 ? crypto/0
712 00:00:00 0.0 ? mtdblockd
741 00:00:00 0.0 ? kpsmoused
789 00:00:00 0.0 ? PETH/Tx
912 00:00:00 0.0 ? angel
1098 00:00:00 0.0 ? telnetd
1414 00:00:00 0.0 pts/0 imish
1415 00:00:00 0.0 pts/0 more
1416 00:00:00 0.0 ? ps
Related CommandsNone
1.23 show processes cpu historyTo display CPU utilization information for a period of time, use the show processes cpuhistory command in Privileged EXEC mode, the period of 1s, 1min, 5min could be shown.
22
Command Syntaxshow process cpu history
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThe following is sample output from the show processes cpu history command:Switch# show processes cpu historyCPU usage for five seconds: 4.17%; one minute: 3.70%; five minutes: 3.68%
Related CommandsNone
1.24 show processes memory sortedTo display memory utilization information about the active processes sorted bypercentage in a device, use the show processes memory sorted command in PrivilegedEXEC mode. Here, CPU usage for each process means the CPU timeslice used by thisprocess from the process was started to this command has been operated.
Command Syntaxshow processes memory sorted (core | physical | virtual)core Size in physical pages of the core image of the process
physical Non-swapped physical memory that a task has used
virtual Virtual memory usage of entire process
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThe following is sample output from the show processes memory sorted commandwithout keywords:Switch# show processes memory sortedTotal: 256108; Used: 89644; Free: 166464; Buffers: 0
PID TTY RSS VSZ SZ COMMAND
1317 pts/0 9516 13104 3276 imish
1106 ? 9428 13104 3276 imish
23
1463 pts/0 7436 13104 3276 imish
956 ? 6836 14644 3661 nsm
1007 ? 5948 9624 2406 imi
924 ? 5912 17652 4413 hsrvd
959 ? 3336 8076 2019 snmpd
1032 ? 2724 8204 2051 bgpd
1027 ? 2488 7140 1785 ospfd
1003 ? 2472 7152 1788 pimd
957 ? 2340 6572 1643 dhcrelay
983 ? 2336 6592 1648 mstpd
1021 ? 2324 6600 1650 ripd
1005 ? 2320 6732 1683 ldpd
942 ? 2284 6772 1693 sshd
985 ? 2208 6592 1648 onmd
929 ? 2132 7168 1792 chsm
966 ? 2028 6140 1535 lacpd
973 ? 2028 6284 1571 authd
965 ? 2024 6408 1602 ptpd
964 ? 1952 6364 1591 oamd
977 ? 1948 6200 1550 rmond
963 ? 1708 5980 1495 bhm
919 ? 1120 3792 948 ntpd
916 ? 1060 2300 575 syslog-ng
1465 pts/0 764 2516 629 ps
917 ? 668 3040 760 crond
1 ? 656 2928 732 init
1464 pts/0 472 1668 417 more
1096 ? 416 2928 732 telnetd
1098 ? 272 2928 732 telnetd
912 ? 172 1496 374 angel
2 ? 0 0 0 kthreadd
3 ? 0 0 0 ksoftirqd/0
4 ? 0 0 0 watchdog/0
5 ? 0 0 0 events/0
6 ? 0 0 0 khelper
9 ? 0 0 0 netns
10 ? 0 0 0 async/mgr
63 ? 0 0 0 sync_supers
65 ? 0 0 0 bdi-default
66 ? 0 0 0 kblockd/0
73 ? 0 0 0 kseriod
88 ? 0 0 0 rpciod/0
105 ? 0 0 0 khungtaskd
106 ? 0 0 0 kswapd0
157 ? 0 0 0 aio/0
164 ? 0 0 0 nfsiod
171 ? 0 0 0 crypto/0
712 ? 0 0 0 mtdblockd
741 ? 0 0 0 kpsmoused
779 ? 0 0 0 jffs2_gcd_mtd1
789 ? 0 0 0 PETH/Tx
Related CommandsNone
24
1.25 terminal monitorTo copy debug output to the current terminal line, use the terminal monitor command inPrivileged EXEC mode.
Command Syntaxterminal monitorterminal no monitor
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThe following is sample output from the terminal monitor commandSwitch# terminal monitorJan 1 16:09:30 DUT1 IMISH-6: ready to service
Related CommandsNone
1.26 configure terminalTo enter global configuration mode, use configure terminal command in Privileged EXECmode.
Command Syntaxconfigure terminal
Command ModePrivileged EXEC
DefaultNone
UsageUse this command to enter global configuration mode. Note that commands in this modeare written to the running configuration file as soon as you enter them (using the Enterkey/Carriage Return).After you enter the configure command, the system prompt changes from<switch-name># to <switch-name>(config)#, indicating that the switch is in globalconfiguration mode. To leave global configuration mode and return to Privileged EXECmode, type end or press Ctrl-Z.
ExamplesIn the following example, the user enters global configuration mode:Switch# configure terminalEnter configuration commands, one per line. End with CNTL/Z.
25
Switch(config)#
Related Commandsenabledisable
1.27 disableTo exit Privileged EXEC mode and return to user EXEC mode, enter the disable commandin EXEC mode.
Command Syntaxdisable
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesIn the following example, the user enters Privileged EXEC mode using the enablecommand, then exits back to user EXEC mode using the disable command. Note that theprompt for user EXEC mode is >, and the prompt for Privileged EXEC mode is #.Switch> enablePassword: <password>
Switch# disableSwitch>
Related Commandsenable
1.28 enableTo enter Privileged EXEC mod, use the enable command in user EXEC or Privileged EXECmode.
Command Syntaxenable
Command ModeUser EXECPrivileged EXEC
DefaultNone
UsageNone
26
ExamplesIn the following example, the user enters Privileged EXEC mode using the enablecommand. The system prompts the user for a password before allowing access to thePrivileged EXEC mode. The password is not printed to the screen. The user then exitsback to user EXEC mode using the disable command. Note that the prompt for user EXECmode is the greater than symbol (>), and the prompt for Privileged EXEC mode is thenumber sign (#).Switch> enablePassword: <password>
Switch# disableSwitch>
Related Commandsdisable
1.29 endTo end the current configuration session and return to Privileged EXEC mode, use theend command in global configuration mode.
Command Syntaxend
Command ModeGlobal Configuration
DefaultNone
UsageThis command will bring you back to Privileged EXEC mode regardless of whatconfiguration mode or configuration sub-mode you are in.This global configuration command can be used in any configuration mode.Use this command when you are done configuring the system and you want to return toEXEC mode to perform verification steps.
ExamplesIn the following example, the end command is used to exit from interface configurationmode and return to Privileged EXEC mode. A show command is used in Privileged EXECmode to verify the configuration.Switch# configure terminalSwitch(config)# interface eth-0-1Switch(config-if)# endSwitch# show interface eth-0-1
Related Commandsexit
27
1.30 exit (global)To exit any configuration mode to the lower mode in the CLI mode hierarchy, use the exitcommand in any configuration mode.
Command Syntaxexit
Command ModeAll Configuration Modes
DefaultNone
UsageThe exit command is used in the CLI to exit from the current command mode to thelower mode in the CLI mode hierarchy.For example, use the exit command in global configuration mode to return to PrivilegedEXEC mode. Use the exit command in interface, line, or router configuration mode toreturn to global configuration mode.
ExamplesThe following example displays an exit from the interface configuration mode to returnto the global configuration mode.Switch(config-if)# exitSwitch(config)#
Related Commandsendexit (EXEC)
1.31 exit (EXEC)To close an active terminal session by logging off the switch, use the exit command inEXEC mode.
Command Syntaxexit
Command ModePrivileged EXEC
DefaultNone
UsageUse the exit command in EXEC mode to exit the active session (log off the device). Thiscommand can be used in any EXEC mode (such as User EXEC mode or Privileged EXECmode) to exit from the EXEC process.
ExamplesIn the following example, the exit (global) command is used to move from globalconfiguration mode to Privileged EXEC mode, the disable command is used to move from
28
Privileged EXEC mode to user EXEC mode, and the exit (EXEC) command is used to logoff (exit the active session):Switch(config)# exitSwitch# disableSwitch> exit
Related Commandsquit
1.32 quitTo close an active terminal session by logging off the switch, use the quit command inEXEC mode.
Command Syntaxquit
Command ModeAll Configuration Modes
DefaultNone
UsageUse the quit command in EXEC mode to exit the active session (log off the device). Thiscommand can be used in any EXEC mode (such as User EXEC mode or Privileged EXECmode) to exit from the EXEC process.
ExamplesIn the following example, the quit command is used to move from global configurationmode to Privileged EXEC mode, the disable command is used to move from PrivilegedEXEC mode to user EXEC mode, and the quit command is used to log off (exit the activesession):Switch(config)# quitSwitch# disableSwitch> quit
Related Commandsexit
1.33 cdChange the current directory to dir, use the cd command in EXEC mode.
Command Syntaxcd (dir| )
dir (Optional) The directory or file systems followed by a colon. Ifflash: argument is specified, change the current directory toflash: . If udisk: argument is specified, change the currentdirectory to udisk:. If you don’t use USB device, failed to cd udisk
29
Command ModePrivileged EXEC
DefaultThe initial default file system is flash:. If you do not specify a directory on a file system,the default is the root directory on that file system.
UsageFor all EXEC commands that have an optional file system argument, the system uses thefile system specified by the cd command when you omit the optional file systemargument. For example, the dir EXEC command, which displays a list of files on a filesystem, contain an optional file system argument. When you omit this argument, thesystem lists the files on the file system specified by the cd command.
Examples In the following example, the cd command is used to set the default file system to
the Flash memory.
Switch # cdSwitch# pwdflash:/
In the following example, the cd command is used to set the file system without plug
in the USB mass storage device
Switch # cd udisk:% Failed to cd udisk:: No such file or directory
In the following example, the cd command is used to set the file system with plug in
the USB mass storage device
Switch # cd udisk:Switch # pwdudisk:/
Related Commandsdirlspwd
1.34 copyTo copy file system, use the copy command in Privileged EXEC mode.
Command Syntaxcopy source-name destination-name
30
source-name The location URL of the source file to be copied. The source canbe either local or remote
destination-name The destination URL of the copied file. The destination can beeither local or remote
Command ModePrivileged EXEC
DefaultNone
UsageThe exact format of the source and destination URLs varies according to the file ordirectory location. You may enter a particular file or a filename that follows the standardfile system syntax (filesystem:[/filepath][/filename]).
ExamplesThe following example shows how to get image from TFTP server through in bandmanagement interface.Switch# copy tftp://192.168.0.1/image flash:/boot/imageDownload from URL to temporary file.
Get file from tftp://192.168.0.1/image
....................................................................................
..........................
Received 15591515 bytes in 16.6 seconds
Copy the temporary file to its destination.
....................................................................................
..........................
15591515 bytes in 69.8 seconds, 218 kbytes/second
The following CLI example shows how to get image from TFTP server throughout bandmanagement interface.Switch# copy mgmt-if tftp://192.168.0.1/image flash:/boot/image
Related Commandsdelete
1.35 deleteTo delete a file on the flash, use the delete command in Privileged EXEC mode.
Command Syntaxdelete file-name
file-name The file name that is supposed to be deleted
31
Command ModePrivileged EXEC
DefaultNone
UsageIf you attempt to delete the configuration file or image, the system prompts you toconfirm the deletion. Also, if you attempt to delete the system specified file such as DHCPsnooping bindings, the system prompts you to confirm the deletion.
ExamplesThe following example deletes the file named test from the flash:Switch# delete flash:/testAre you sure to delete flash:/test? [confirm]:y
Related Commandscopy
1.36 dirTo display a list of files on a file system, use the dir command in EXEC mode.
Command Syntaxdir (flash: | udisk: | ) (directory-name | ) (file-name | )
flash The flash system
udisk The USB mass storage device. If you don’t use USB mass storagedevice, failed to dir udisk
directory-name The directory in flash or udisk
file-name The file name
Command ModePrivileged EXEC
DefaultNone
UsageUse the dir (Flash file system) command to display flash or udisk information.
ExamplesThe following is sample output from the dir command.Switch# dirDirectory of flash:/
total 42
32
drwxr-xr-x 2 0 Jul 30 15:42 boot
drwxr-xr-x 3 0 Jan 1 1970 conf
drwxr-xr-x 2 0 Jan 1 1970 log
-rw-r----- 1 1020 Jul 29 19:18 startup-config.conf
-rw-r--r-- 1 10270 Jul 30 10:10 syslog
-rw-r--r-- 1 6886 Jul 29 23:59 syslog.1.gz
63.0M bytes total (30.4M bytes free)
Switch#
The following is sample output from udisk if plug in the USB mass storage device.Switch # cd udisk:Switch # dirDirectory of udisk:/
total 12
drwxrwxrwx 2 4096 Jun 2 2011 test
drwxrwxrwx 2 4096 Jun 8 2011 test1
drwxrwxrwx 2 4096 Jun 7 2011 test2
3.7G bytes total (3.7G bytes free)
Related Commandsls
1.37 lsTo display a list of files on a file system, use the ls command in EXEC mode.
Command Syntaxls (flash: | udisk: | ) (directory-name | )(file-name | )
flash The flash system
udisk The USB mass storage device. If you don’t use USB mass storagedevice, failed to dir udisk
directory-name The directory in flash or udisk
file-name The file name
Command ModePrivileged EXEC
DefaultNone
UsageUse the ls (Flash file system) command to display flash or udisk information.
ExamplesThe following is sample output from the ls command.Switch# ls
33
Directory of flash:/
total 42
drwxr-xr-x 2 0 Jul 30 15:42 boot
drwxr-xr-x 3 0 Jan 1 1970 conf
drwxr-xr-x 2 0 Jan 1 1970 log
-rw-r----- 1 1020 Jul 29 19:18 startup-config.conf
-rw-r--r-- 1 10270 Jul 30 10:10 syslog
-rw-r--r-- 1 6886 Jul 29 23:59 syslog.1.gz
63.0M bytes total (30.4M bytes free)
Related Commandsdir
1.38 moreTo display the contents of a file, use the more command in EXEC mode.
Command Syntaxmore (flash: | udisk:) (directory-name|)file-name
flash The flash system
udisk The USB mass storage device. If you don’t use USB mass storagedevice, failed to dir udisk
directory-name The directory in flash or udisk
file-name The file name
Command ModePrivileged EXEC
DefaultNone
UsageThe system can only display a file in ASCII format.
ExamplesThe following partial sample output displays the configuration file named startup-configin flash.Switch# more flash:/startup-config.conf
Related Commandsdirls
1.39 mkdirTo create a new directory in a Flash file system or udisk device, use the mkdir commandin EXEC mode.
34
Command Syntaxmkdir directory-name
directory-name The directory in flash or udisk
Command ModePrivileged EXEC
DefaultNone
UsageThis command is valid only for local file systems.
ExamplesThe following example creates a directory named newdir in Flash.Switch# mkdir flash:/newdir
The following example creates a directory named newdir in USB mass storage device ifplug in it.Switch# mkdir udisk:/newdir
Related Commandsrmdirdir
1.40 renameTo rename a file in a Class C Flash file system or udisk device, use the rename commandin EXEC mode.
Command Syntaxrename old-filename new-filename
old-filename The original file name in flash
new-filename The new file name in flash
Command ModePrivileged EXEC
DefaultNone
UsageThis command is valid only for local file systems.
35
ExamplesIn the following example, the file named startup-config.conf-bak is renamedstartup-config.conf-bak2.Switch1# rename udisk:/wus udisk:/wuAre you sure to rename udisk:/wus? [confirm]
Related CommandsNone
1.41 rmdirTo remove an existing directory in a Flash file system or udisk device, use the rmdircommand in Privileged EXEC mode.
Command Syntaxrmdir directory-name
directory-name The directory in flash
Command ModePrivileged EXEC
DefaultNone
UsageThis command is valid only for local file systems.
ExamplesThe following example creates a directory named newdir.Switch# rmdir flash:/newdirAre you sure to delete newdir? [yes/no]: y
Related Commandsmkdirdir
1.42 tar createTo create an new tar file in a Flash file system or udisk device, use the tar createcommand in Privileged EXEC mode.
Command Syntaxtar create tar-file-name source-directory
36
tar-file-name The file name of the new tar file
source-directory The source directory in flash
Command ModePrivileged EXEC
DefaultNone
UsageThe source-directory must be a directory.
ExamplesThe following example creates a tar file named tar1.Switch# tar create udisk:/tar1 udisk:/wu
Related Commandstar tabletar xtract
1.43 tar tableTo display files in the tar file, use the tar table command in Privileged EXEC mode.
Command Syntaxtar table tar-file-name
tar-file-name The file name of the new tar file
Command ModePrivileged EXEC
DefaultNone
UsageThe tar-file-name must be a in the flash.
ExamplesThe following example shows files in a tar file named tar1.Switch# tar table udisk:/tar1
Related Commandstar createtar xtract
37
1.44 tar xtractTo untar files in the tar file, use the tar xtract command in Privileged EXEC mode.
Command Syntaxtar xtract tar-file destination-directory
tar-file The file name of the tar file
destination-directory The destination directory
Command ModePrivileged EXEC
DefaultNone
UsageThe destination-directory must exist in the flash. You can use mkdir to create a newdirectory.
ExamplesThe following shows an example to extract a tar file named tar1 into a directory namedir1:Switch# tar xtract flash:/tar1 flash:/mydir
Related Commandstar createtar table
1.45 tar diagnostic-informationTo put diagnostic-information to a Flash file system ,udisk device, ftp server or tftpserver, use the tar diagnostic-information command in Privileged EXEC mode. Syslogfiles, core dump files, tcam entries ,running-config, startup-config, version, clock,memory and logging buffer are included in this tarfile.
Command Syntaxtar diagnostic-information (mgmt-if | ) destination-directory/ tar-file
destination-directory The destination directory, such as flash, udisk, tftp or ftpserver
tar-file The file name of the tar file
Command ModePrivileged EXEC
38
DefaultNone
UsageThe destination-directory must reachable and disk is enough.
ExamplesThe following shows an example to put a diagnostic-information tar file to flash:Switch# tar diagnostic-information flash:/diag.tar.gz
Related CommandsNone
1.46 formatTo format udisk, all data on udisk: will be lost.
Command Syntaxformat udsik:
udsik: The USB mass storage device. If you don’t use USB mass storagedevice, failed to format udisk
Command ModeApplication Configure mode
DefaultNone
UsageThe destination-directory must exist.
ExamplesThe following shows an example to format USB mass storage device:Switch(config)# format udisk:
WARNING: All data on udisk: will be lost!!!
And format operation may take a while.
Are you sure to process with format? [yes/no]: yes
Related CommandsNone
1.47 umountTo uninstall the USB mass storage device before plug out it from the switch.
Command Syntaxumount udsik:
39
udisk: The USB mass storage device. If you don’t use USB mass storagedevice, failed to format udisk
Command ModeApplication Configure mode
DefaultNone
UsageUSB mass storage device must exist in the system. You can use umount command touninstall the USB mass storage device.
ExamplesThe following shows an example to umount USB mass storage device:Switch(config)# umount udisk:After this operation, you can not use USB disk.
Are you sure to continue? [yes/no]: yes
Related CommandsNone
1.48 umountTo enable cut through mode, and can configure speed only on GG truck .
Command Syntaxcut_through_forwarding enable (10G-40G-100G| 1G-10G-100G| 1G-10G-40G|)
enbale enable cut through mode
(10G-40G-100G|1G-10G-100G|1G-10G-40G|)
Configure cut_through speed
Command ModeApplication Configure mode
Default10G-40G-100G
UsageNone
ExamplesDUT4# cut-through-forwarding enable 1G-10G-40G% Configuration about cutting through forwarding mode has been stored, but cannottake effect until the next reload.
40
Related CommandsNone
41
2 User Management Commands
2.1 usernameUse this command to create or delete a local user account on the switch.
Command SyntaxusernameWORDno usernameWORD
username Establish User Name Authentication
WORD User name
Command ModeGlobal Configuration
DefaultNone
UsageNone
ExamplesThis is a sample output from this command displaying how to add a user namedtestName.Switch (config)#username testName
Related CommandsNone
2.2 username passwordUse this command to add username and password.
Command SyntaxusernameWORD password (8|) LINE
WORD User namePassword Password for username
42
(8|) Specifies a hidden password will follow
LINE User password string
Command ModeGlobal Configuration mode
DefaultNone
UsageNone
ExamplesThis is a sample output from this command displaying how to add a user namedtestName and with the password of 123456.Switch(config)# username testName password 123456
Related CommandsNone
2.3 username secretUse this command to add username and password and the password will be encryptedby the switch.
Command SyntaxusernameWORD secret LINE
WORD User namesecret Specify the secret for the userLINE User privilege level
Command ModeGlobal Configuration
DefaultNone
UsageNone
ExamplesThis is a sample output from this command displaying how to add a user namedtestName and with the password of 123456.Switch (config)#username testName secret 123456
43
Related CommandsNone
2.4 username privilegeUse this command to set a local user account with privilege level on the switch.
Command SyntaxusernameWORD privilege <1-4>
WORD User name
privilege <1-4> ser privilege level
Command ModeGlobal Configuration
DefaultNone
UsageNone
ExamplesThis is a sample output from this command displaying how to add a user with privilegelevel of 2.Switch(config)#username testName privilege 2
Related CommandsNone
2.5 username privilege passwordUse this command to set a local user account with privilege level and password on theswitch.
Command SyntaxusernameWORD privilege <1-4> password (8|) LINE
WORD User name
privilege <1-4> User privilege level
8 Specifies a HIDDEN password will follow
LINE User privilege level
44
Command ModeGlobal Configuration
DefaultNone
UsageNone
ExamplesThis is a sample output from this command displaying how to add a user with privilegelevel of 2 and password of 123456.Switch(config)# username testName privilege 2 password 123456
Related CommandsNone
2.6 re-username newnameUse this command to reset username.
Command Syntaxre-usernameWORD newnameWORD
re-usernameWORD
Old user name
newnameWORD New user name
Command ModeGlobal Configuration
DefaultNone
UsageNone
ExamplesThis is a sample output from this command displaying how to reset username.Switch(config)# re-username testName newname newname
Related CommandsNone
2.7 cipher detectUse this command to set high level of cipher detect.
45
Command Syntaxcipher detect (strong| normal | none)
strong Cipher must contain digital, normal char and special char
normal Cipher must contain digital and normal char
none Disable security check
Command ModeGlobal Configuration
DefaultNone
UsageNone
ExamplesThis is a sample output from this command displaying how to set high level of cipherdetect.Switch(config)# cipher detect strong
This cmd will make all un-strong clear text passwords lost!
Related CommandsNone
46
3 FTP Commands
3.1 ftpTo exchange files between local and remote ftp server, use the ftp command in PrivilegedEXEC mode.
Command Syntaxftp (mgmt-if | ) host
mgmt-if Management port
host IPv4, IPv6 address or name of the remote host
Command ModePrivileged EXEC
DefaultNone
UsageUse the ftp command to upload and download files from remote ftp server.
ExamplesThe following is sample output from the ftp command:Switch# ftp mgmt-if 10.10.29.160Connected to 10.10.29.160.
220---------- Welcome to Pure-FTPd ----------
220-You are user number 1 of 50 allowed.
220-Local time is now 09:00. Server port: 21.
220-IPv6 connections are also welcome on this server.
220 You will be disconnected after 15 minutes of inactivity.
Name (10.10.29.160:root): root
331 User root OK. Password required
Password:
230-User root has group access to: wheel disk adm sys daemon
230- bin root
230 OK. Current directory is /root
Remote system type is UNIX.
Using binary mode to transfer files.
ftp>
47
Switch # ftp mgmt-if 2001:1000::2Connected to 2001:1000::2 (2001:1000::2).
220 Serv-U FTP Server v10.2 ready...
Name (2001:1000::2:root): Fiberstore
331 User name okay, need password.
Password:
230 User logged in, proceed.
Remote system type is UNIX.
Using binary mode to transfer files.
ftp>
Related CommandsNone
3.2 ftp vrfTo exchange files between local and remote ftp server in VPN, use the ftp vrf command inPrivileged EXEC mode.
Command Syntaxftp vrfWORD
WORD VPN Routing/Forwarding instance name
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThe following is sample output from the ftp vrf command:Switch# ftp vrf testvrf
Related CommandsNone
3.3 ftp usernameTo create an FTP username, use the ftp username command in global configurationmode. To remove an FTP username, use the no form of this command.
Command Syntaxftp username usernameno ftp username
48
username The user name of the remote FTP server
Command ModeGlobal Configuration
DefaultNo ftp username is defined.
UsageThe username must also follow the rules. They must start with a letter, and have asinterior characters only letters, digits, and underline. Names must be 31 characters orfewer.
ExamplesThe following example creates an FTP username “abc”:Switch(config)# ftp username abc
Related Commandsftp passwordftp passive
3.4 ftp passwordTo create the password of an FTP username, use the ftp password command in globalconfiguration mode. To remove the password of an FTP username, use the no form ofthis command.
Command Syntaxftp password(passowrd | 8 passowrd)no ftp password
password The password of the user name of the remote FTP server
8 Specifies a hidden password will follow
Command ModeGlobal Configuration
DefaultNo ftp password is defined.
UsageThe password will be encrypted in running-config if service password-encryption isenabled.
ExamplesThe following example creates the ftp password:
49
Switch(config)# ftp password abc
Related Commandsftp usernameftp passive
3.5 ftp passiveTo set the FTP mode in passive mode, use the ftp passive command in globalconfiguration mode. To restore the configuration to the default, use no form of thiscommand.
Command Syntaxftp passiveno ftp passive
Command ModeGlobal Configuration
DefaultFTP works in Active mode.
UsageNone
ExamplesThe following example sets the ftp mode to passive:Switch(config)# ftp passive
Related Commandsftp usernameftp password
3.6 show ftpTo display the ftp configurations, use show ftp command in Privileged EXEC mode.
Command Syntaxshow ftp
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThe following example displays the ftp configurations:Switch# show ftpftp passive mode: on
50
ftp username: root
ftp password: unencrypted, abc
Related Commandsftp usernameftp passwordftp passive
51
4 TFTP Commands
4.1 copy GFILENAME GURLNAMEUse this command to copy local file to tftp server.
Command Syntaxcopy GFILENAME (mgmt-if | ) GURLNAME
mgmt-if Management port
GFILENAME Copy to URL
GURLNAME Copy to local file
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThis is a sample output from the command displaying how to copy local file to tftpserver.Switch# copy flash:/test.c tftp://1.1.1.1/running-config
Related CommandsNone
4.2 copy GURLNAME GFILENAMEUse this command to copy file from tftp server to local.
Command Syntaxcopy (mgmt-if| ) GURLNAME GFILENAME
mgmt-if Management port
52
GURLNAME Copy from URL
GFILENAME Copy to local file
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThis is a sample output from the command displaying how to copy file from tftp serverto local.Switch# copy tftp://1.1.1.1/test.c flash:test1.cget file from tftp://1.1.1.1/test.c
.
Received 225 bytes in 0.3 seconds
Related CommandsNone
4.3 copy running-config mgmt-ifUse this command to copy running-config to tftp server.
Command Syntaxcopy running-config (mgmt-if| ) GURLNAME
startup-config Copy from current system configuration
mgmt-if Management port
GFILENAME Copy to URL
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThis is a sample output from the command displaying how to copy running-config to tftp server.
53
Switch#copy running-config tftp://1.1.1.1/running-config
Building configuration...
send file to tftp://1.1.1.1/running-config
..
Sent 40198 bytes in 8.3 seconds
Related CommandsNone
4.4 copy startup-config mgmt-ifUse this command to copy startup-config to tftp server.
Command Syntaxcopy startup-config (mgmt-if| ) GURLNAME
startup-config Copy from current system configuration
mgmt-if Management port
GFILENAME Copy to URL
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThis is a sample output from the command displaying how to copy startup-config to tftpserver.Switch# copy startup-config tftp://1.1.1.1/startup-configsend file to tftp://1.1.1.1/startup-config
..
Sent 32252 bytes in 6.4 seconds
Related CommandsNone
4.5 copy mgmt-if startup-configUse this command to copy startup-config from tftp server.
Command Syntaxcopy (mgmt-if| ) GURLNAME startup-config
54
mgmt-if Management port
GURLNAME Copy from URL
startup-config Copy to startup system configuration
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThis is a sample output from the command displaying how to copy startup-config fromtftp server.Switch #copy tftp://1.1.1.1/startup-config startup-configget file from tftp://1.1.1.1/startup-config
..
Sent 32252 bytes in 6.4 seconds
Related CommandsNone
55
5 SCP Commands
5.1 copy GFILENAME GURLNAMEUse this command to copy local file to remote host.
Command Syntaxcopy GFILENAME (mgmt-if | ) GURLNAME
mgmt-if Management port
GFILENAME Copy to URL
GURLNAME Copy to local file
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThis is a sample output from the command displaying how to copy local file to remotelinux host.Switch# copy flash:/test.c mgmt-if scp://username@10.10.38.160:/tftpboot/test.cSend file to scp://username@10.10.38.160:22/tftpboot/test.c
username@10.10.38.160's password:
test.c 100% 1768 1.7KB/s 00:00
Related CommandsNone
5.2 copy GURLNAME GFILENAMEUse this command to copy file from remote host to local.
Command Syntaxcopy (mgmt-if| ) GURLNAME GFILENAME
56
mgmt-if Management port
GURLNAME Copy from URL
GFILENAME Copy to local file
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThis is a sample output from the command displaying how to copy file from remote hostto local.Switch# copy mgmt-if scp://username@10.10.38.160:/tftpboot/test.c flash:/test1.cDownload from URL to temporary file.
Get file from scp://username@10.10.38.160:22/tftpboot/ttt
username@10.10.38.160's password:
test.c 100% 1768 1.7KB/s 00:00
Copy the temporary file to its destination.
.
1768 bytes in 0.0 seconds, inf kbytes/second
Related CommandsNone
57
6 Telnet Commands
6.1 telnetUse this command from the switch to access the other devices in the network.
Command Syntaxtelnet ( vrfWORD | mgmt-if )WORD (PORT |)
vrfWORD VPN Routing/Forwarding instance
mgmt-if Management port
WORD IPv4, IPv6 address or hostname of a remote system
PORT TCP Port number
Command ModePrivileged EXEC
DefaultNone
UsageNone
ExamplesThis example shows how to Telnet from the switch to a remote host.Switch# telnet mgmt-if 10.10.29.247Entering character mode
Escape character is '^]'.
TestOS, Version 2.3(62), fcs
Switch# telnet 2001:1000::1
Entering character mode
Escape character is '^]'.
58
DUT1#
Related CommandsNone
59
7 SSH Commands
7.1 ip ssh serverTo enable SSH service, use ip ssh server enable command in global configuration mode.To disable SSH service, use ip ssh server disable command.
Command Syntaxip ssh server (enable | disable)
enable Turn on the SSH service
disable Turn off the SSH service
Command ModeGlobal Configuration
DefaultSSH service is enabled.
UsageNone
ExamplesThe following example enables the SSH service on your switch:Switch(config)# ip ssh server enable
Related Commandsshow ip ssh server status
7.2 ip ssh server authentication-retriesTo configure Secure Shell (SSH) authentication retry times on your switch, use the ip sshserver authentication-retries command in global configuration mode. To restore thedefault value, use the no form of this command.
Command Syntaxip ssh server authentication-retries integerno ip ssh server authentication-retries
60
integer The number of retries, with a maximum of 6 authenticationretries
Command ModeGlobal Configuration
DefaultThe default is 6.
UsageNone
ExamplesThe following examples configure SSH authentication retry times on your switch.Switch(config)# ip ssh server authentication-retries 3
Related Commandsshow ip ssh server status
7.3 ip ssh server authentication-timeoutTo configure Secure Shell (SSH) authentication timeout on your switch, use the ip sshserver authentication-timeout command in global configuration mode. To restore thedefault value, use the no form of this command.
Command Syntaxip ssh server authentication-timeout secondsno ip ssh server authentication-timeout
seconds The number of seconds until timeout disconnects, with amaximum of 120 seconds
Command ModeGlobal Configuration
DefaultThe default is 120 seconds.
UsageNone
ExamplesThe following examples configure SSH authentication timeout on your switch:Switch(config)# ip ssh server authentication-timeout 100
Related Commandsshow ip ssh server status
61
7.4 ip ssh server authentication-typeTo configure Secure Shell (SSH) authentication type on your switch, use the ip ssh serverauthentication-type command in global configuration mode. To restore the default value,use the no form of this command.
Command Syntaxip ssh server authentication-type (all |{password | public-key | rsa})no ip ssh server authentication-type
all Enable all authentication type
password Enable password authentication
public-key Enable SSHv2 public key authentication
rsa Enable SSHv1 rsa authentication
Command ModeGlobal Configuration
DefaultThe default authentication type is all.
UsageNone
ExamplesThe following examples configure SSH authentication type on your switch.Switch(config)# ip ssh server authentication-type password
Related Commandsshow ip ssh server status
7.5 ip ssh server host-key rsa keyTo configure Secure Shell (SSH) host-key on your switch, use the ip ssh server host-keyrsa key command in global configuration mode. To restore the default value, use the noform of this command.
Command Syntaxip ssh server host-key rsa key keyno ip ssh server host-key rsa
key The key value for host key
Command ModeGlobal Configuration
62
DefaultThere is no host-key defined.
UsageNone
ExamplesThe following examples configure SSH host key on your switch:Switch(config)# ip ssh server host-key rsa key KEY1
Related Commandsshow ip ssh server status
7.6 ip ssh server rekey-intervalTo configure Secure Shell (SSH) rekey interval on your switch, use the ip ssh serverrekey-interval command in global configuration mode. To restore the default value, usethe no form of this command.
Command Syntaxip ssh server rekey-intervalminuteno ip ssh server rekey-interval
minute The rekey interval, with a maximum of 1440 minutes
Command ModeGlobal Configuration
DefaultThe default interval is 60 minutes.
UsageNone
ExamplesThe following examples configure SSH rekey interval on your switch:Switch(config)# ip ssh server rekey-interval 30
Related Commandsshow ip ssh server status
7.7 ip ssh server versionTo configure Secure Shell (SSH) version on your switch, use the ip ssh server versioncommand in global configuration mode. To restore the default value, use the no form ofthis command.
Command Syntaxip ssh server version (1 | 2 | all)
63
no ip ssh server version
1 Switch runs only SSH Version 1
2 Switch runs only SSH Version 2
all Version 1 and Version 2 are both supported
Command ModeGlobal Configuration
DefaultThe default SSH version is 2.
UsageYou can use this command with the 2 keyword to ensure that your switch will notinadvertently establish a weaker SSH Version 1 connection.
ExamplesThe following example shows that only SSH Version 1 support is configured:Switch(config)# ip ssh server version 1The following example shows that only SSH Version 2 is configured:Switch(config)# ip ssh server version 2The following example shows that SSH Versions 1 and 2 are configured:Switch(config)# no ip ssh server version
Related Commandsshow ip ssh server status
7.8 show ip ssh server sessionTo display the session information for Secure Shell (SSH), use the show ip ssh serversession command in Privileged EXEC mode.
Command Syntaxshow ip ssh server session
Command ModePrivileged EXEC
DefaultNone
UsageUse the show ip ssh server session command to view the session information.
ExamplesThe following example shows the current SSH sessions:Switch# show ip ssh server sessionVersion Encryption Hmac User IP State
64
=================================================================
2.0 aes128-cbc hmac-md5 abc 10.10.29.22 Session started
Related Commandsshow ip ssh server status
7.9 show ip ssh server statusTo display the version and configuration data for Secure Shell (SSH), use the show ip sshserver status command in Privileged EXEC mode.
Command Syntaxshow ip ssh server status
Command ModePrivileged EXEC
DefaultNone
UsageUse the show ip ssh server status command to view the version and configuration data.
ExamplesThe following example shows the current SSH configurations:Switch# show ip ssh server statusSSH server enabled
Version: 1.99
Authentication timeout: 33 second(s)
Authentication retries: 6 time(s)
Server key lifetime: 60 minute(s)
Authentication type: password, public-key
Related Commandsshow ip ssh server session
7.10 rsa key generateTo create a key by system, use the rsa key generate command in global configurationmode.
Command Syntaxrsa key keyname generate
keyname The name of the key
Command ModeGlobal Configuration
DefaultNone
65
UsageUse the rsa key command to create a key by system.
ExamplesThe following example creates a key named KEY1:Switch(config)# rsa key KEY1 generateGenerating RSA private key, 1024 bit long modulusPlease waiting for a moment: done!Public exponent is 65537 (0x10001)Generate RSA key successfullySwitch(config)#
Related Commandsshow rsa keys
7.11 rsa keyTo create a key, use the rsa key command in global configuration mode.
Command Syntaxrsa key keyname
keyname The name of the key
Command ModeGlobal Configuration
DefaultNone
UsageUse the rsa key command to create a key.
ExamplesThe following example creates a key named KEY1:Switch(config)# rsa key KEY1Switch(config-rsa-key)#
Related Commandsshow rsa keys
7.12 key formatTo specify the key format, use the key format command in RSA key configuration mode.
Command Syntaxkey format (der | pem)
66
der The format is der
pem The format is pem
Command ModeRsa Key Configuration
DefaultThe default key format is DER.
UsageUse the key format command to specify the key format.
ExamplesThe following example specify the key format of KEY1 as der :Switch(config)# rsa key KEY1Switch(config-rsa-key)# key format der
Related Commandsrsa key
7.13 key string endTo exit the rsa key configuration mode to global configuration mode and apply all rsa keyconfigurations, use the key string end command in RSA key configuration mode.
Command Syntaxkey string end
Command ModeRsa Key Configuration
DefaultNone
UsageUse the key string end command to exit the rsa key configuration mode.
ExamplesThe following example shows exit the rsa key configuration mode :Switch(config)# rsa key KEY1Switch(config-rsa-key)# key string endSwitch(config)#
Related Commandsrsa key
7.14 key typeTo specify the key type, use the key type command in RSA key configuration mode.
67
Command Syntaxkey type (public | private)
public Specify the key as a public key
private Specify the key as a private key
Command ModeRsa Key Configuration
DefaultNone
UsageUse the key type command to specify the type of the key.
ExamplesThe following example specifies the key type of KEY1 as public key:Switch(config)# rsa key KEY1Switch(config-rsa-key)# key type public
Related Commandsrsa key
7.15 resetTo clear all key configurations, use the reset command in RSA key configuration mode.
Command Syntaxreset
Command ModeRsa Key Configuration
DefaultNone
UsageUse the reset command to clear all key configurations.
ExamplesThe following example shows to clear all configurations for the key KEY1:Switch(config)# rsa key KEY1Switch(config-rsa-key)# reset
Related Commandsrsa key
68
7.16 validateTo check the validation of the key strings, use the validate command in RSA keyconfiguration mode.
Command Syntaxvalidate
Command ModeRsa Key Configuration
DefaultNone
UsageUse the validate command to clear all key configurations.
ExamplesThe following example shows to validate key strings of the key KEY1:Switch(config)# rsa key KEY1Switch(config-rsa-key)# validate
Related Commandsrsa key
7.17 KEYLINETo add key strings from the screen directly, type any strings in RSA key configurationmode except the keywords in this mode.
Command SyntaxKEYLINE
Command ModeRsa Key Configuration
DefaultNone
UsageType any key string.
ExamplesThe following example shows to type a key string of the key KEY1:Switch(config)# rsa key KEY1Switch(config-rsa-key)# 00302017 4A7D385B 1234EF29 335FC973Switch(config-rsa-key)# 2DD50A37 C4F4B0FD 9DADE748 429618D5
Related Commandsvalidate
69
7.18 rsa key exportTo export the key file to a specified destination, use the rsa key export command inglobal configuration mode.
Command Syntaxrsa key keyname export url destination-file (public | private) (der | der-hex | pem |ssh1 | ssh2)
keyname Specify the key name to display
destination-file The destination file path and name
public Specify the key as a public key
private Specify the key as a private key
der DER format
der-hex DER HEX format
pem PEM format
ssh1 SSHv1 format
ssh2 Specify the key format
der DER format
Command ModeGlobal Configuration
DefaultNone
UsageUse rsa key generate command to generate a key.
ExamplesThe following example shows to export the key KEY1 to flash as a public key:Switch(config)# rsa key KEY1 export url flash:/key1.pub public ssh2The following example shows to export the key KEY2 to flash as a private key:Switch(config)# rsa key KEY2 export url flash:/key1 private ssh1
Related Commandsrsa key generatersa key import
7.19 rsa key importTo import the key file from a specified source, use the rsa key import command in globalconfiguration mode.
70
Command Syntaxrsa key keyname import url source-file (public | private) (der | der-hex | pem | ssh1 |ssh2)
keyname Specify the key name to display
source-file The destination file path and name
public Specify the key as a public key
private Specify the key as a private key
der DER format
der-hex DER HEX format
pem PEM format
ssh1 SSHv1 format
ssh2 Specify the key format
Command ModeGlobal Configuration
DefaultNone
UsageUse the rsa key to generate command to generate a key.
ExamplesThe following example shows to import the key KEY1 to flash as a public key:Switch(config)# rsa key KEY1 import url flash:/key1.pub public ssh2
The following example shows to import the key KEY2 to flash as a private key:Switch(config)# rsa key KEY2 import url flash:/key1 private ssh1
Related Commandsrsa key generatersa key export
7.20 show rsa keyTo display the details of the keys, use the show rsa key command in Privileged EXECmode.
Command Syntaxshow rsa key keyname
keyname Specify the key name to display
71
Command ModePrivileged EXEC
DefaultNone
UsageUse the rsa key generate command to generate a key.
ExamplesThe following example displays the detailed information of the key named “KEY1”:Switch# show rsa key KEY1RSA key information:
============================================================
Name: KEY1
Type: private
Modulus: 1024 bit
Usage count: 0
Private key DER code:
30820258
0201
00
028180
9B3E9726 6405BD54 692F172A 901F3879 C947366E 5703D282 AA31707F 214D38C9
Related Commandsshow rsa keys
7.21 show rsa keysTo display the brief information of all the keys, use the show rsa keys command inPrivileged EXEC mode.
Command Syntaxshow rsa keys
Command ModePrivileged EXEC
DefaultNone
UsageUse the rsa key generate command to generate a key.
ExamplesThe following example displays the brief information of the keys:Switch# show rsa keysName Type Usage Modulus
============================================================
key1 private 0 1024
key2 public 0 1024
72
Related Commandsshow rsa key
7.22 sshTo connect to the remote SSH server, use the ssh command in Privileged EXEC mode.
Command Syntaxssh -l NAME ({-i KEYNAME | -p DPORT | -v (1|2) | -c{3des|des|3des-cbc|aes128-cbc|aes192-cbc|aes256-cbc} | -m{hmac-md5-128|hmac-md5-96|hmac-sha1-160|hmac-sha1-96} | -onumberofpasswordprompts NUM}|) (mgmt-if|) (A.B.C.D|X:X::X:X|HOST)
-l NAME Log in using this user name
-i KEYNAME Specify the name of RSA private key
-p DPORT Specify the remote port
-v (1|2) Specify SSH protocol version
-c Select encryption algorithm
3des Triple DES (SSHv1 only)
des DES (SSHv1 only)
3des-cbc Triple DES (SSHv2 only)
aes128-cbc AES 128 bits (SSHv2 only)
aes192-cbc AES 192 bits (SSHv2 only)
aes256-cbc AES 256 bits (SSHv2 only)
-m Select HMAC algorithm
hmac-md5-128 MD5 based HMAC (128 bits, SSHv2 only)
hmac-md5-96 MD5 based HMAC (96 bits, SSHv2 only)
hmac-sha1-160 SHA1 based HMAC (160 bits, SSHv2 only)
hmac-sha1-96 SHA1 based HMAC (96 bits, SSHv2 only)
-o numberof-passwordprompts NUM
Specify number of password prompts with the range in[1, 5]
mgmt-if Use Management port
A.B.C.D Specify IP address of remote system
X:X::X:X Specify IPv6 address of remote system
HOST Specify hostname of remote system
Command ModePrivileged EXEC
DefaultNone
73
UsageNone
ExamplesThe following example displays the usage of this command:Switch# ssh -l aaa -v 2 1.1.1.1aaa@1.1.1.1's password:
Switch#
Related Commandsip ssh server
74
8 Time&Timezone
8.1 clock set datetimeUse this command to set system current date and time on the Switch.
Command Syntaxclock set datetime hh:mm:ss month day year
hh:mm:ss Specify the time in hours (24-hour format), minutes, and seconds.The time specified is relative to the configured time zone
month Specify the month by name, should be in range 1 to 12
day Specify the day by date in the month, should be in range 1 to 31
year Specify the year, should be in range 2000 to 2037
Command ModeGlobal Configuration
DefaultThe default time is based from UTC.
UsageIf no other source of time is available, you can manually configure the time and date afterthe system is restarted. The time remains accurate until the next system restart. Werecommend that you use manual configuration only as a last resort. If you have anoutside source to which the switch can synchronize, you do not need to manually set thesystem clock.
ExamplesThis example shows how to manually set the system clock to 1:32 p.m. on July 23, 2014:Switch(config)# clock set 13:32:00 23 7 2014
Related Commandsshow clock
8.2 clock set timezoneUse this command to set the time zone on the Switch.To restore to the default time of UTC, use the no form of this command.
Command Syntaxclock set timezone ZONE (add |minus) hours-offset [minutes-offset] [seconds-offset]no clock set timezone
75
ZONE Specify the zone name, the length should be [3, 32), and only[a-zA-Z_] is supported, and the first and last character must bealphabet.
add Specify the time offset is positive from UTC
minus Specify the time offset is negative from UTC
hours-offset Specify the time offset in hours, should be in range 0 to 23
minutes-offset [optional]Specify the time offset in minutes, should be in range0 to 59
seconds-offset [optional]Specify the time offset in seconds, should be in range 0to 59
Command ModeGlobal Configuration
DefaultThe default time zone should be UTC.
UsageNone
ExamplesThe following example sets the Atlantic Canada time zone is 3.5 hours less than UTC.Switch(config)# clock set timezone Canada minus 3 30
Related Commandsshow clock (detail)
8.3 clock set summer-timeUse this command to set summer time (daylight saving time) in areas where it starts andends on a particular day each year(recurring) or on specified year(date).To restore to the default time of UTC, use the no form of this command.
Command Syntaxclock set summer-time ZONE recurring start-time end-time offsetclock set summer-time ZONE date start-time end-time offsetno clock set summer-time
ZONE Specify the summer zone name, the length should be [3, 32), andonly [a-zA-Z_] is supported, and the first and last character mustbe alphabet.
recurring Specify that summer time starts and ends on a particular day ofthe week each year
date Specify that summer time starts and ends on a particular day ofthe specified year
76
start-time Specify the start time of summer time, for recurring summertime, the format should bemonth, day, hh:mm:ss, while for datesummer time, the format should bemonth, day, year, hh:mm:ss
end-time Specify the end time of summer time, for recurring summertime, the format should bemonth, day, hh:mm:ss, while for datesummer time, the format should bemonth, day, year, hh:mm:ss
offset For offset, specify the number of minutes to add during summertime. The default is 60.
Command ModeGlobal Configuration
DefaultSummer time should be disabled by default.
UsageThe first part of the clock summer-time global configuration command specifies whensummer time begins, and the second part specifies when it ends. All times are relative tothe local time zone. The start time is relative to standard time. The end time is relative tosummer time. If the starting month is after the ending month, the system assumes thatyou are in the southern hemisphere.
ExamplesThis example shows how to specify that summer time starts on june 1st at 02:00 andends on the October 31 at 02:00:.Switch(config)# clock set summer-time recurring 6 1 02:00:00 10 31 02:00:00 120
Related Commandsshow clock (detail)
8.4 show clockUse this command to display the current time and date configuration.
Command Syntaxshow clock (detail|)
detail Display the configured timezone and summer time information inaddition to current date and time
Command ModePrivileged EXEC mode
DefaultNone
UsageNone
ExamplesThis example displays current time and date in detail:
77
Switch(config)#show clock detail10:43:00 beijing Fri Oct 25 2013
Time zone: (GMT + 08:00:00) beijing
Related Commandsshow clock
8.5 show timezonesUse this command to display all the timezones in world.
Command Syntaxshow timezons
Command ModePrivileged EXEC mode
DefaultNone
UsageNone
ExamplesThis example displays all the current timezones:Switch(config)#show timezones(GMT+00:06:04) Europe/Andorra
(GMT+03:41:12) Asia/Dubai
(GMT+04:36:48) Asia/Kabul
(GMT-04:07:12) America/Antigua
(GMT-04:12:16) America/Anguilla
(GMT+01:19:20) Europe/Tirane
(GMT+02:58:00) Asia/Yerevan
(GMT-04:36:00) America/Curacao
(GMT+00:52:56) Africa/Luanda
(GMT+11:06:24) Antarctica/McMurdo McMurdo Station, Ross Island
============================================================
(GMT+00:00:00) Antarctica/South_Pole Amundsen-Scott Station, South Pole
(GMT-04:32:32) Antarctica/Rothera Rothera Station, Adelaide Island
(GMT-04:16:24) Antarctica/Palmer Palmer Station, Anvers Island
78
Related Commandsshow clock
79
9 License Commands
9.1 generate device identifierTo generate device identifier, use this command in Privileged EXEC mode.
Command Syntaxgenerate device identifier (mgmt-if | ) GURLNAMEgenerate device identifier (GFILENAME|)
mgmt-if Management port
GURLNAME URL name
GFILENAME local file name
Command ModePrivileged EXEC
DefaultNone
UsageThis command will generate the unique device identifier (UDI) on the current device,customer can get license for the current device form Fiberstore with UDI.
ExamplesThe following example shows how to generate UDI:Switch# generate device identifier mgmt-if tftp://10.10.38.160/device.udi
Related CommandsNone
9.2 show licenseTo show license on the device, use the show license command in Privileged EXEC mode.
Command Syntaxshow license (GFILENAME|)
GFILENAME local file name
80
Command ModePrivileged EXEC
DefaultNone
UsageThis command will show the license on the current device.
ExamplesThe following example shows how to show license:Switch# show linceseLicense files:
======================================================================
flash:/ma.lic:
Created Time: Fri Dec 6 17:22:23 CST 2013
Vendor: Fiberstore
Customer: Fiberstore
Device MAC: 00:1E:08:09:03:00
Feature Set: QINQ MVR ERPS MEF ETHOAM
VPWS VPLS HVPLS SMLK TPOAM
OSPF PIM_SM IGMP VRF MPLS
LDP BGP RSVP OSPF_TE EXTEND_ACL
PTP BFD SSM IPV6 OSPF6
PIM_SM6 MVR6 RIPNG TUNNEL_V6
Related CommandsNone