Range

Weightanka

Wireanka

Accessanka

1

2

Class E Deadweight

Anchor Device

to EN 795:1996ISO 14567

Class E Deadweight Anchor Systemand Class ‘C’

Horizontal Lifeline system

to EN 795:1996

Class B & E Portable

Deadweight Anchor system for

Rope Access to EN 795:1996

Features

For roofs up to 5 degrees pitch

Suitable for wet or dry roof surface

Easy and quick assembly

Galvanised to BS EN ISO 1461

3

4

Base weightsBase weights fully encased in rubber

Rubber moulding means base weights aren’t prone to peeling

Unique design adds to performance

Reduces thermal bridging

5

Galvanised Counter weightsEach counterweight weighs 25kg and incorporate carrying handles

Different roof types require different Counterweight quantities

6

PlacementEnsure outside of Kee Anchor product is at least 2.5m from any roof edge, open void or fall hazard.

• Do not position in areas where there is a risk of contamination or accumulation of water, oil, grease or algae

• On Gravel covered roofs, brush gravel to allow anchor bases direct contact with roof material

7

PlacementSuitable Roof Types- Up to 5º Pitch

Concrete

Asphalt Mineral Felt

Stone chippings

Single ply membrane (Smooth)

Steel cladding

8

LimitationsUse with suitable PPEEnsure roof structure is suitable, any doubts Kee Safety recommends seeking the advice of a structural engineer

9

Fall Restraint

Combination of anchor position and PPE supplied ensures no user is able to reach a position of 0.5m of any roof edge, roof open or other fall hazard

10

Cleaning/Storage

The assemblies should be kept clean, using detergent if necessary, by wiping or hosing down with clean water and dried.Storage should be in a dry, chemically inert environment, away from sources of damage and Store in such a way that dismantled products will not become lost or misplaced.Where the Weightanka has been left in position an optional cover is available.

11

Before installationIt is strongly recommended that installers assemble and disassemble one in a place of safety, away from the worksite to familiarise themselves with the product

12

Class E Deadweight Anchor Device toEN 795:1996ISO 14567

CE Certified to PPEDirective

13

14

Portable, Non Penetrative, Temporary or permanent solution

• Ideal for Where Roof build up is unknown• No Roof Alterations required• Good for refurbishment projects• Quick to assemble• No part of the Weightanka weighs more than 25kg

15

Number Of Users

Fall Arrest- Single User

Restraint- Two Users• Tell Kee Safety at time of purchasing• Supplied with 2nd Eyebolt & Restraint PPE disc.

16

Number of weights250kg (Six Galvanised weights) assembly for:

Asphalt/MasticMineral Felt Concrete (Brushed) Stone chippings on Bitumen

300kg (Eight Galvanised weights) assembly for: • Single ply membrane (Smooth)• Steel cladding • (Brushed) Stone chippings on Asphalt/Mastic.

17

Stack weights opposite each other vertically

18

Assembly TOOLS REQUIRED FOR

ASSEMBLY:

12mm A/F Hex Allen key

19

Class ‘E’ Deadweight Anchor System

and Class ‘C’ Horizontal Flexible Lifeline

to EN 795:1996 and BS 7883

CE Certified to PPEDirective

20

21

Non penetrative EN795 ‘Class C’ Wire cable systemAllows users to be continuously attachedUp to 15 m spansFor temporary or permanent installationNo need to water proofSystem incorporates cornersFall arrest or restraint

22

Non penetrative EN795 ‘Class C’ Wire cable systemAllows users to be continuously attachedUp to 15 m spansFor temporary or permanent installationNo need to water proofSystem incorporates cornersFall arrest or restraint

23

Layout optionsSINGLE EXTREMITY ANCHORS

Fall Arrest for a single user

-Or alternatively-

• Fall Restraint for up to 3 users (maximum 2 users in a single span)

24

Layout optionsDOUBLE EXTREMITY/CORNER ANCHORS

Fall Arrest for 2 users in separate spans

25

Edge distances and maximum spansFALL ARREST SYSTEMS

FALL RESTRAINT Maximum 10 m spans Minimum edge distance of 2.5m

15m12m10m8m6m5mMaximum span

7.2m6.6m6.2m5.8m5.4m5.2mMin. Free Fall Distance

4.0m4.0m3.0m3.0m2.5m2.5mMin. Edge Distance

26

Portable Deadweight System for Rope Access

Conforms to BS EN 795, & ISO 14567 class B&E

CE Approved to PPE Directive

Single user for Roped Access applications

• Two users in a rescue situation

27

28

Separate anchor points for working line and back up lineInternal force balanced system allows the assembly to remain static.Requires no attachment to structural membersEasily moved across roof surface, removing need for multiple attachment points Rope lines held away from edge of building reducing risk of abrasion

29

Used with a 250kg Weightanka Assembly for any roof type Sold separately for use with existing Weightanka or as complete systemAluminium, galvanised and rubber coated partsMinimum maintenanceProvides full fall arrest protection before approaching edge

30

UsageAccessanka is an accessory to Weightanka and must always be used in combination with it.This combination provides a mobile deadweight anchor device for use in rope access systems in accordance with:Industrial Rope Access Trade Association (IRATA)

guidelinesand/or:

BS7985:2002 – Code of practice for the use of rope access methods for industrial purposes

31

More information

Identification labelsAssembly and operating instructions Sales LiteratureSales teamTechnical supportwww.keesafety.co.uk

Kee Safety Ltd

32

1 Boulton RoadReadingRG2 0NHUnited KingdomTel: +44 (0) 118 931 1022Fax: +44 (0) 118 931 1146Email: sales@keesafety.comwww.keesafety.co.uk