Post on 26-Feb-2021
MOUNTING
The following recommendations are given so that the best results may be obtained in using diamond wheels: Care should be taken in mounting a diamond wheel. Flanges, back plates and spindle should be clean, free of burrs, and run true. By using an indicator and tapping lightly on a wood block held against the wheel, indicate the wheel is within .0005" of true rotation. Tighten the flanges securely and recheck with an indicatopr before using. When mounting a cup type wheel, use shims inserted between the back plate and the wheel to obtain a true running face. The use of permanent mounting should be practiced where convenient.
WHEEL DRESSING AND TRUING
Due to the exceptionally free cutting properties of the diamond wheels, frequent dressing is not necessary. They may be dressed with a soft bonded aluminum oxide or silicon carbide dressing stick. When a beveled or gouged condition has ocurred in a face type wheel, the wheel may be removed from the machine and rotated in a figure 8 motion on a glass or cast iron plate sprinkled with 80 to 100 grit silicon carbide dust. To true a peripheral type wheel which has become beveled at the corners, let the diaond wheel revolve at a slow speed mounted on a mandrel between lathe centers and true at right angles with a small silicon carbide wheel mounted on tool post grinder.
GRINDING SPEEDS AND FEEDS
The best speeds for diamond wheels for grinding carbide is between 5,000 to 6,000 surface feet per minute. Slightly higher are not detrimenta.l, particulary if a flood of coolant is applied and grinding pressure minimized. Table traverse rates of 100" to 500" per minute with cros feeds of .030 to .060 may be used. The diamond wheel may be used with down feeds of .125" when hand fed across the work. For general surface grinding operations, down feeds should not exceed .001 per pass, for rougher grits and .00025 should be used for used for finish grinding or with fine grit wheels.
COOLANT
It has been found that generous flow of coolant increases diamond wheel efficiency. The proper placement of coolant is also important. The coolant must be applied in the proper place or it will not cool the wheel or the material being ground, properly. Coolant should always be directed so that the full flow is at the point of contact between the same direction as the rotation of the wheel.
11889 Teale Street, Culver City, CA 90230 - toll-free (800) 818-7512 - fax-free(800) 803-7374 - tel (310) 915-1111 - fax (310) 390-5793
t----+---------+-----4 12A2-45SS
WHEEL TYPE AND SHAPE
PageType Shape
Page Type Shape No.No.
1A1 10
18
14U1 11
,�126A2 12V5-45 17
13 196A2SP 12A2-20
14 209A3 12R4
16/16.1 21
12A2-45 12V5-20
1511V9-70 221209
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
' '
'
33
WHEEL TYPE AND SHAPE
PageType Shape No.
PageType Shape
No.
1A1R
12A2-45DB
12A2-20DB
12M2-45
1V1
A1PP
AOKF
30
31
32
34
. : 35. . .
. . .. 36.
14EE1X
1EE1X
1FF1X
1FF6V
1GG1V
6A2T
23
24
25
26
28
29
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
Technical
urn
200/160 200/160 D 213 2121180 200/160
D 91
80/63
50/40 50/40
D46 45/38 D45 D50
DIAMOND GRIT SIZE DESIGNATION
UKAM Specifications
FEPA 150565 DIN 848 DIN 4188 ANSI 874-16
Designation
630/500
Sieves Main
Fraction,
630/500
Designation
D601
Sieves Aperture, Jlrn
630/500
Designation
Fine Coarse
D500 D500
For Main Fraction, Jlrn
630/500
USA Grit Size (Mesh)
30/35
500/400 500/400 D501 500/425 D450 D500 500/400 35/40
400/315 400/315 D426 425/355 D350 400/315 40/45
D356 355/300 D350 45/50
315/250
250/200
315/250
250/200
D301
D 251
300/250
250/212
D280 D250
D220 D250
315/250
250/200
50/60
60/70
D 181 180/125
D 180 D 150
D 180 D 150
70/80
80/100
160/125 1601125 D 151 125/125 D 140 D 150 160/125 100/120
125/100 125/100 D 126 125/106 D 110 D 100 125/100 120/140
100/80
80/63
100/80
80/63
D 107 106/90
90/75
D90 D 100
D90 D70
100/80 140/170
170/200
63/50 63/50
D76
D64
75/63
63/53
D65 D70
D55 D50
200/230
230/270
D54 53/45 D45 D50 63/50
50/40
270/325
325/400
NOTE: The Table is based on data of Industial Diamond Association of America, Inc.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
, '-
-----'-
----� '-
-----------
-"
......
ex>
en
a} g.) CD
g]
CD
J'l.
()
c
1FF1X;14EE1X;1EE1X
Typical Applications of Metal Bond Diamond Abrasive Tool
Bond Type Wheel Type Applications Page
M2-01
12R4 Wet Sharpening of multipoint carbide tool 20
14 EE1X; IEE1X Wet thread grinding 23,24 1A1R Wet cutting of nonmetallic materials 30
12A2-45
1A1
Wet faceting of plate glass
Wet machining of ceramics
16,16.1
10 M1-04 1A1; 12A2-45; 1FF1X Complete wet diamond grinding of combinations of steel and carbide 10,16,16.1,31,24
M1-10 1A1; 12A2-45 Wet machining of composite hardfacing materials 10,16,16.1,31
M3-16 1 A 1 ;12A2-45 Grinding ceramics. Wet grinding of optical and technical glasses
Profile Grinding. Wet grinding of tungsten carbide chipbreaker grooves
10,16,16.1,31
23,24,25
M1-05 12A2-45; 6A2 Grinding (including deep grinding) carbide inserts and a part of steel shanks. Finish sharpening of carbide tool without coolant. Wet grinding carbides
16,16.1,31
M2 09-1
M2-17
12V5-20; 12A2-20; 6A2;
9A3; 14U1; 11V9-70;
12V5-45; 12D9; 1A1; 1FF1X
1 A 1; 6A2; 12A2-45
Wet sharpening of multipoint metal-cutting carbide tool. Grinding carbide/steel combinations. Wet machining of high-speed steels
Electrolytic grinding of high-speed and other steels
10,11,12,13 14,15,17,21 19,20,22,25
32
10,12,31
M020-2 1 A 1; 12A2-45; 6A2 Electrolytic grinding of high-speed steels and carbide/steel combinations 10,12,18,31
MC-2 /M013A 6A2; 6A2 SP Electrolytic sharpening of carbide cutting tool 12,13
M1P A1PP Grooving ferrite parts of magnectic heads, articles of ceramics, glass, special heat resistant and nonmetallic materials
35
M3-19 AOKF Cutting and grinding polycore, quartz, ferrites and other hard brittle nonmetallic materials 36
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
Typical Applications of Resin Bond Diamond Abrasive Tool
Bond Type Wheel Type Applications Page
82·01
82-07
12A2-4S;9A3; 1A1; 12V5-45; 12A2-20 1209; 14EEIX;1EEIX
12A2-45; 1 1 V9-70; 12V5-45;
12A2-20;12RY; 1209; 12V5-20
14EEIX; 1EEIX 1FFIX
Finishing grinding. Wet and dry grinding and finishing of carbide tool. Grinding carbide shaving·cutters and gear·cutters.
Grinding and finishing carbide tool.
10,16,16.1 14,17,32 22,23,24
16,16.1 15,17,19,20 21,22,23,24
25
82-08
1A1; 6A2; 9A3; 12R4; 12A2-45; 12V5-45; 1209;
12VS-20; 1 EEIX 1FFIX; 14EEIX
Finish grinding of titanium alloys and steels. High-efficient sharpening of carbide tool.
10,12,14,20 16,16.1,17,21
22,23,24,25
81-11P
83-01-1
12A2-45; 12A2-4SSS; 12A2-20
12A2-20; 12A2-4S;6A2;
12VS-4S
Sharpening carbide single-point tool
Finish grinding of cylindrical surfaces of steel and carbide components. Surface grinding of soft-magnetic materials.
16,16.1,18,19
12,16,16.1 17,19
811-L
1A1; 14U1; 12A2-4S;9A3;
12A2-20; 1209; 11 V9-70; 12VS·4S;
12VS-20
Grinding nonmetallic materials. Sharpening carbide single-point tool. 10,11,16,16.1 14,1S, 17,19
21,22
6A2; 12A2-4S 9A3
Grinding components from superabrasive-based composites. 12,17,14
11869 Teale Street, Culver City, CA 90230 • toll-free (800) 618·7512 - fax-free(800) 603-7374 - tel (310) 915-1111
xln:& x ln:& w 10
Xrs 10 rs10
rs10 Xrs 10 Xrs 10
x ln:& xln:&
!
I IThe
XIW::!:5
XIW 5 XIW 5
XIW 5
IThe
Recommendations for use metal and resin bonds
Wheel Shape
Bond Type
Metal
M2-01 M1·04 M1-10 M3-16 M1-05 M013 M2-09-1 M2·17 M020-2
1A1
14U1
x X X X
X X
X n:&
6A2 X s=3 X 5=3 X X X w 5
6A2(sp) X X w 5
9A3 X X w 5
12A2·45 X s=3 s:3 X s:3 X X X w 5
12A2-45SS X
11V9-70 X X
12V5-45 X X
12A2·20 X X X X X w 5
12R4 X
12V-20 X X
1209 X X
14EE1X X X X
1EE1X X X X
1FF1X
1FF6V
2FF6V
1CC1V
X X
X X
6A2T X
1A1R X X
12A2-45
12A2·20
12M2·45
1V1 X X
A1PP
AOKF
Bond Type
Metal Resin
MC2 M3-19 M5-22 M1P B2·01 B2-07 B2·0& B1·11P B3·01-1
X X X X
B11-P
X
X X X X
X X X w 5 X w 5 X
X
X X w::!:5 X w::!:5 X
X X w::!:5 X w 5 X
X
X X
X X w 5 X
X
X
X X X w 5 X X
X X
X X X X X w 5 X
X X w 5
X X
X X
X X
X
X
X
X X
X
0The bond is used for this wheel type
W(X.T.) 3 bond is used in wheels with W(X.T.) 3mm
Note: 1. Resin bond wheels work dry
W{X.T.) S; 3 bond is used in wheels with W(X.T.) s;3mm
2. Metal bond wheels work wet
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603·7374 - tel (310) 915-1111
I
DIAMOND CONCENTRATION
Wheel Type
Diamond Concentration Page
25 50 75 100 15 0 No.
1A1 X X X X
14U1 X X X
6A2 X X X X
6A2SP X X X X
9A3 X X X X
12A2-45DB X X X X
11V9-70 X X X
12A2-45SS X X X X
12V5-45 X X X X
12A2-20
12R4
12V5-20
X X X X
X X X X
X X X
1209 X X X
14EE1X X X X
1EE1X X X X
1FF1X X X X
1FF1X X X X
1FF6V X X X
2FF6V X X
1GG1V X X
6A2T X X
1A1R X X X X
12A2-45 DB X X X X
12A2-20DB X X X X
12M2-45 X X X X
1V1 X X
A1PP X X
AOKF X X
ill The diamond concentration is used for this wheel type
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
6
75
40
400
6
400
o •
W
he
el
Dia
me
ter
1A1
T·
Wh
ee
l Th
ickn
ess
S
tra
igh
t W
he
el
Dia
mo
nd
on
Pe
rip
he
ry
H·
Arb
or
X •
D
iam
on
d D
epth
o
AP
PL
ICA
TIO
NS
: C
ylin
drica
l grin
ding
, con
ical g
rindi
ng a
nd s
urfa
ce g
rindi
ng (m
ore
info
rmat
ion
see
page
s 6n
)
grinding the
51 50
o - Wheel Diameter T - Wheel Thickness H - Arbor14U1 X - Diamond Depth
Straight wheel u Face Thickness -Diamond in periphery
APPLICATIONS: Cylindrical of workpiece faces and recesses at one setting of woork (more information pages 6/7)
0 u X S 1 S 2 T H* Item No.
150
5.91
8
.315
4
.157
3
.118
1.5
.059
10
.394
32
1.26
5 1
2.00 11-1000
150
5.91
10
.394
6
.236
3
.118
1.5
.059
10
.394
32
1.26
5 1
2.00 11-1001
200
7.81
12
.472
5
.197
3
.116
2.0
.079
16
.63
32
1.26
5 1
2.00 11-1002
200
7.81
14
.551
10
.394
3
.118
2.0
.079
16
.63
32
1.26
51
2.00 11-1003
250
9.84
16
.630
8
.315
4
.157
3.0
.118
20
.787
76
2.992
51
2.00 11-1004
250
9.84
20
.787
12
.472
4
.157
3.0
.118
20
.787
76
2.992
5 1
2.00 11-1005
NOTE: All dimensions in the table in Milimeters{mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool H Diamond Concentration (see page 9.) 11-10000 14U1 x x
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
.787 925
32
.787
4.92
.197
40 10
.197
;w
6A2
Straight Cup Diamond in Rim
D - Wheel Diameter T - Wheel Thickness H - Arbor X - Rim Depth W - Rim Width E - Back Thickness D
APPLICATIONS: Grinding and finishing cutting tools. Surface grinding{more information pages 6(1)
D W X H* T E Item No. 80
3.15
5
1.97
1.5
.059
20
.787
18.5
.728
9
.354 12-1000
80
3.15
5
1.97
10
.384
3.0
.118
20
.787
20
.787
9
.354 12-1001
100
3.94
100
3.94
125
5
1.97
5
1.97
5
1.97
10
.384
10
.384
10
.384
1.5
.059
1.5
.059
3
.118
20
20
32
1.26
32
1.26
1.26
23.5
25.0
.984
23.5
.925
10
.394
10
394
10
.394
12-1002
12-1003
12·1004
125
4.92
150
5.91
150
5.91
5
1.97
5
1.97
5
1.97
10
.384
10
.384
10
.384
20
.787
20
.787
3.0
.118
3
.118
5
32
1.26
32
1.26
32
1.26
51
2.00
51
2.00
25.0
.984
23.0
.906
25.0
.984
10
.394
10
.394
10
.394
12-1005
12-1006
12-1007
200 7.87
10
.384
20
.787
40
1.575
3.0
.118
32
1.26
51
2.00
76
2.99
23.0
.906
10
.394 12·1008
200 9.84
10
.384
20
.787
40
1.575
5
.197
32
1.26
51
2.00
76
2.99
25.0
.984
10
.394 12-1009
250
9.84
10
.384
20
.787
40
1.575
3.0
.118
51
2.00
76
2.99
127
5.00
23.0
.906
10
.394 12-1010
250
9.84
10
.384
20
.787 1.575
5
.197
51
2.00
76
2.99
127
5.00
25.0
.984 .394 12-1011
300 11.81
20
.787
40
1.575
60
2.362
3.0
.118
76
2.99
30.0
1.26
10
.394 12-1012
300 11.81
20
.787
40
1.575
60
2.362
5 76
2.99
32.0
1.26
10
.394 12-1013
100
3.94
10
.384
15
.591
4
.157
20
.787
24
.945
10
.394 12-1014
125
4.92
10
.384
15
.591
4
.157
32
1.26
24
.945
10
.394 12-1015
150
5.91
10
.384
20
.787
4
.157
6
.236
32
1.26
51
2.00
24
.945
26
1.024
10
.394 12-1016
200 7.87
10
.384
20
.787
40
1.575
4
.157
6
.236
51
2.00
76
2.99
29
1.41
31
1.22
13
.394 12-1017
250
9.84
10
.384
20
.787
40
1.575
4
.157
6
.236
51
2.00
76
2.99
29
1.41
31
1.22
13
.394 12-1018
300 11.81
10
.384 .787
40
1.575
60
2.362
4
.157
6
.236
76
2.99
127
5.00
31
1.22
33
1.299
13
.394 12-1019
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (.) dimensions in bold type. Example how to order: Item No. Type wheel or tool W X T H Diamond Concentratlon(see page 9)
12-1000 6A2 x 5 x 2.0 x 18.5 x 20 x 25
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
... ...
finishing. gauges, information 6/7)
D .. Wheel Diameter T.. Wheel Thickness H.. Arbor X .. Rim Depth
W - Rim Width
Double Rim Cup E T E - Back Thickness
Diamond in Rims
9A3
I
H*
D
APPLICATIONS: Tool and cutter grinding and Machining micrometers and other measuring tools (more pages
D W X T H* E Item No.
150 5.91
5
.197
10 .394
20 .787
3 .118
16
.63
32 1.26
51 2.00
9
.354 14-1000
200 7.87
5
.197
10 .394
20 .787
3 .118
16
.63
32 1.26
51
2.00
76
2.992
9
.354 14·1001
200 7.87
5 .197
10 .394
20 .787
5 .197
20 .787
32 1.26
51
2.00
51
2.00
9
.354 14-1002
250 9.84
250 9.84
10 .394
10 .394
20 .787
20 .787
3 .118
5 .197
21
.827
25 .827
76
2.992
76
2.992
127
5.00
127
5.00
13 .512
13 .512
14·1003
14·1004
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool W H Diamond Concentration(see page 9.) 14-1000 9A3 x 5 x 32 x 25
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street. Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
3x08.5 I-r- ----"--
o D • Wheel Diameter T· Wheel Thickness H • Arbor X - Rim Depth W - RimWidth
6A2SP Straight Cup E - Back Thickness Diamond in Rim DI Diameter Between -
holes
APPLICATIONS: Electrolytic grinding of carbide tools (more information pages 6/7)
D W X H* T DI E Item No.
150 5.91
10 .394
15 .591
20 .787
2 .079
32 1.26
25 .984
70 2.156
13 .512
13-1000
175 6.890
10 .394
15 .591
20 .787
30 1.181
2 .079
50 1.969
25 .984
70 2.156
13 .512
13-1001
200 7.87
10 .394
15 .591
20 .787
30 1.181
2 .079
50 1.989
25 .984
70 2.156
13 .512 13-1002
250 9.84
10 .394
20 .787
30 1.181
2 .079
76 2.992
25 .984
100 3.937
17 .67
13-1003
250 9.84
10 .394
20 .787
30 1.181
3 .118
76 2.992
26 1.024
100 3.937
17 .67
13-1004
300 11.81
20 .787
25 .984
30 1.181
2 .079
102 4.016
30 1.181
160 6.3
17 .67
13-1005
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool W H Diamond Concentration (see page 9.) 13-1000 6A2 SP x 10 x 32 25
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
i
i
D Wheel Diameter -T Wheel Thickness -H Arbor-X Rim Depth -11V9-70 u - Insert Length
Flaring Cup E - Back Thickness Diamond in Periphery
APPLICATIONS: Grinding and finishing broaches, reamers, gun drills and other cutting tools (more information pages 6/7)
0 u X H* T E Item No.
50 3 1.5 16 20 6 15-1000
1.969 .118 .059 .63 .787 .236
80 5 2.0 20 32 8 15-1001
3.15 .197 .019 .787 1.26 .315
75 6 2.0 20 32 8 15-1002
2.953 .236 .079 .787 1.26 .315
100 6 2.0 20 40 8 15-1003
3.94 .236 .079 .787 1.575 .315 100 10 2.0 20 40 8
15-10043.94 .394 0.79 .787 1.575 .315
125 6 3 32 40 8 15-1005
4.921 .236 .118 1.26 1.575 .315
125 8 3 32 40 12 15-1006
4.921 .315 .118 1.26 1.575 .472
125 10 3 32 40 12 15-1007
4.921 .394 .118 1.26 1.575 .472
150 6 3 32 40 12 15-1008 5.91 .236 .118 1.26 1.575 .472
150 10 3 32 51 40 12 15-1009
5.91 .394 .118 1.26 2.00 1.575 .472
NOTE: All dimensions in the table in Milimeters(mm) for reference inches C') dimensions in bold type.
Example how to order: Item No. Type wheel or tool u H Diamond Concentration(see page 9.) 15-1000 11A9-70 x 3 x 16 x 50
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 • toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
3.94 10
10
12A2-45
Flaring Cup
Diamond in Rim
o - Wheel Diameter T - Wheel Thickness H - Arbor X - Rim Depth W - Rim Width E - Back Thickness
APPLICATIONS: Tool and cutter grinding and finishing. Surface grinding (more information pages 6/7)
D W X T H* E Item No.
so
3.15
5
.197
10
.394
3
.118
26.5
1.043
20
.787
s
.315 16-1000
100
3.94
100
3.94
6
.236
6
.236
10 .394
3
.118
4
.157
26.6
1.043
27.0
1.063
20
.787
20
.787
10
.394
10
.394
16-1001
16-1002
100
3.94
6
.236
10
.394
5
.197
2S.0
1.102
20
.787
10
.394 16-1003
100
100
3.94
5
.197
5
.197
10
.394
10 .394
3
.118
5
.197
32.0
1.26
34.0
1.339
20
.787
20
.787
32
1.26
32
1.26
10
.394
.394
16-1004
16-1005
125
4.921
6
.236 .394 3
.118
26.0
1.024
20
.787
32
1.26
12
.472 16-1006
125
4.921
6
.236
10
.394
4
.157
27.0
1.063
20
.787
32
1.26
12
.472 16-1007
125
4.921
6
.236
10
.394 5
.197
2S.0
1.102
20
.787
32 1.26
12
.472 16-1008
125
4.921
5
.197
10
.394
3
.118
40.0
1.575
32
1.26
12
.472 16-1009
125
4.921
5
.197
10
.394
5
.197
42.0
1.654
32
1.26
12
.472 16-1010
150
5.91
6
.236
10
.394
15
.591
3
.118
26.0 1.024
32 1.26
12 .472
16-1011
150
5.91
6
.236
10
.394
15
.591
3
.118
2S.0
1.102
32
1.26
12
.472 16-1012
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (II ) dimensions in bold type.
Example how to order: Item No. Type wheel or tool W H Diamond Concentration(see page 9.) 16-1000 12A2-45 x 5 x 20 x 50
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
12A2-45
Flaring Cup
Diamond in Rim
D - Wheel Diameter T - Wheel Thickness H - Arbor X· Rim Depth W - Rim Width E Back Thickness -
APPLICATIONS: Tool and cutter grinding and finishing. Surface grinding (more information pages 617)
D W X T H* E Item No.
150
5.91
5
.197
10
.394
20
.787
3
.118
40.0
1.575
32
1.26
51
2.00
12
.472 16 .. 1013
150
5.91
5
.197
10
.394
20
.787
5
.197
42.0
1.654
32
1.26
51
2.00
12
.472 16 .. 1014
175
6.890
175
6.890
6
.236
6
.236
10
.394
10
.394
15
.591
15
.591
3
.118
4
.157
26.0
1.024
27.0
1.063
51
2.00
51
2.00
12
.472
12
.472
16-1015
16 .. 1016
175
6.890
6
.236
10
.394
15
.591
5
.197
28.0
1.024
51
2.00
12
.472 16 .. 1017
200
7.87
10
.394
15
.591
20
.787
3
.113
26.0
1.024
51
2.00
76
2.992
12
.472 16-1018
200
7.87
10
.394
15
.591
20
.787
5
.197
28.0
1.102
51
2.00
76
2.992
12
.472 16-1019
200
7.87
10
.394
20
.787
3
.118
50.0
1.97
32
1.26
51
2.00
76
2.992
14
.551 16-1020
200
7.87
10
.394
20
.787
5
.197
52.0
2.047
32
1.26
51
2.00
76
2.992
14
.551 16 .. 1021
250
9.84
10
.394
15
.591
20
.787
3
.118
26.0
1.024
76
2.992
12
.551 16·1022
250
9.84
10
.394
15
.591
20
.787 5
.197
28.0
1.102
76
2.992
12
.472 16-1023
250
9.84
250
9.84
10
.394
10
.394
20
.787
20
.787
3
.118
5
.197
50.0
1.97
50.0
1.978
51
2.00
51
2.00
76
2.992
76
2.992
127
5.00
127
5.00
14
.551
14
.551
16-1024
16-1025
NOTE: All dimensions in the table in Milimeters(mm) for reference inches el) dimensions in bold type.
Example how to order: Item No. Type wheel or tool W H Diamond Concentration(see page 9.) 16-1000 12A2-45 x 5 x 32 x 25
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
12
D -
Wh
ee
l Dia
me
ter
W
T -
Wh
ee
l Th
ickn
ess
12V5-45
H -
Arb
or
Fla
rin
g C
up
X
-R
im D
ep
th
Dia
mo
nd
in R
im
x
W -
Rim
Wid
th
T
E -
Ba
ck T
hic
kne
ss
AP
PL
ICA
TIO
NS
: G
rin
din
g a
nd
fin
ish
ing
sp
ira
l-flu
ted
mu
ltito
oth
to
ols
on
the
fla
nk(
mo
re in
form
atio
n s
ee
pa
ge
617)
D
W
X
H*
T
E
Ite
m N
o.
50
3
3
1
6
20
6
1.9
69
.1
18
.1
18
.6
3
.78
7
.23
6
17
-10
00
80
3.1
5
3
.11
8
5
.19
7
3
.11
8
20
.78
7
25
.98
4
8
.31
5
17
-10
01
10
0
3.9
4
5
.19
7
4
.15
7
20
.78
7
32
1.2
6
32
1.2
6
10
.39
4
17
-10
02
12
5
3
4
32
4
0
4.9
21
.1
18
.1
57
1
.26
1
.57
5
.47
2
15
0
5.9
1
5
.19
7
32
1.2
6
50
1.9
7
51
2.00
40
1.5
75
12
. 47
2
17
.. 10
04
NO
TE
: A
ll d
ime
ns
ion
s i
n t
he
ta
ble
in
Mi li
me
ters
(mm
) fo
r re
fere
nc
e i
nc
he
s (
" )
dim
en
sio
ns
in
bo
ld t
yp
e.
Ex
am
ple
ho
w t
o o
rde
r:
Ite
m N
o.
Ty
pe
wh
ee
l o
r to
ol
W
H
Diamond C
on
cen
tra
tion(s
ee
page 9.)
17
-10
00
1
2v5
-45
x
3
x
1
6
x
50
*An
oth
er
size
of
arb
or
(H)
as
re
qu
ire
d.
Ord
er
form
se
e p
ag
e 4
2.
12A2-4SSS
(with a discontinuos diamond layer)
Flaring Cup
Diamond in Rim
T
D - Wheel Diameter T - Wheel Thickness H - Arbor X· Rim Depth W - Rim Width E - Back Thickness
APPLICATIONS:Grinding and sharpening carbide tools (more information pages en)
D W X H* T E Item No.
125
4.91
10
.394
5
.197
32
1.26
44
1.732
32
1.26 18-1000
150 5.91
10 .394
10 .394
3
.118
5
.197
32
1.26
32
1.26
42
1.654
44
1.732
30
1.181
32
1.26
18-1001
18-1002
20
.787
5
.197
32
1.26
44
1.732
32
1.26 18-1003
200
7.87
20
.787
5
.197
76
2.992
54
2.126
40
1.575 18-1004
250
9.84
20
.787
5
.197
76
2.992
54
2.126
40
1.575 18-1005
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool H Diamond Concentration(see page 9.) 18-1000 12A2-45SS x 32 x 50
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(8001 i \ 7374 - tel 0) 915-1111
D Wheel Diameter -T - Wheel Thickness H - Arbor12A2-20 X Diamond Depth -W - Rim Width
Dish Wheel E - Back Thickness Diamond in Rim
APPLICATIONS:Grinding and finishing reamers, solid and assembled cutters, disk saws, broaches and other types of cutting tools(more information pages 6/7)
D W X H* T E Item No.
80 3.15
3 .118
5 .197
1.5 .059
20 .787
10 .394
6
.236 19-1000
100 3.94
3 .118
5 .197
1.5 0.59
20 .787
32 1.26
10 .394
6
.236 19-1001
100 3.94
2 0.079
20 .787
12 .472
6
.236 19-1002
125 4.921
3 .118
5 .197
10 .394
1.5 0.59
32 1.26
13 .512
9
.354 19-1003
125 4.921
3 .118
6
.236
2 0.072
32 1.26
16 .630
8 .315 19-1004
150 5.91
3 .118
5 .197
10 .394
1.5 0.59
32 1.26
51 2.0
16 .630
10 .394 19-1005
150 5.91
3 .118
6
.236
10 .394
2 0.072
32 1.26
51 2.0
18 .630
9
.354 19-1006
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool W H Diamond Concentration(see page 9.} 19-1000 12A2-20 x 3 x 20 x 50
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) r;" . 7374 tel i ' ) 915-111 1-
D - Wheel Diameter
T - Wheel Thickness
H Arbor-X - Diamond Depth 12R4 W - Rim Width
Dish Wheel E - Back Thickness Diamond in Rim
APPLICATIONS:Grinding and finishing multitooth tools on the face (more information pages 6/7)
D W X H* T E Item No.
80 3.15
3 .118
2 .079
20 .787
10 .394
6 .236
20-1000
100 3.94
3 .118
2 .079
20 .787
32 1.26
10 .394
6 .236
20-1001
125 4.921
3 .118
2 .079
32 1.26
13 .512
9
.354 20-1002
150 5.91
3 .118
5 .197
2 .079
32 1.26
51 2.00
16 .315
10 .394
20-1003
NOTE: All dimensions in the table in Milimeters(rnm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool W H Diamond Concentration(see page 9.) 20-1000 12R4 x 3 x 20 x 50
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
IE
'------'------'-
APPLICATIONS:Grinding 617)
D Wheel Diameter-T Wheel Thickness H - Arbor X Diamond Depth -12V5-20
-
W Rim Width -Dish Wheel Back Thickness -Diamond in Rim 0.0- Angle
X T
and finishing multitooth spiral-fluted tools on the face (more information pages
D W X H* T E 0.0
Item No.
100
3.94
3
.118
5
.197
1.5
.059
2
.079
20
.787
10
.394
6
.236 15 21-1000
125
4.921
3
.118
5
.197
2
.079
32
1.26
13
.512
9
.354 15 21-1001
150
5.91
10
.394
3
.118
32
1.26
51
2.0
16
.630
10
.394 15 21-1002
NOTE: All dimensions in the table in Milimeters(mm) for reference inches r) dimensions in bold type.
Example how to order: Item No. Type wheel or tool W X T H Diamond Concentration(see page 9) 21-1000 12V5-20 x 3 x 2 x 10 x 20 x 100
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
9
.984
5.9
1
.98
4
20
0
7.8
7
.98
4
D -
Whe
el
Dia
me
ter
T -
Wh
ee
l T
hic
kne
ss
12 9
H -
Arb
or
Dis
h W
he
el
T
X -
Dia
mon
d D
ep
th
Dia
mo
nd
in
Pe
rip
he
ry
W-
Rim
Wid
th
E -
Ba
ck
Th
ickn
es
s
0. ° . A
ng
l e
AP
PL
ICA
TIO
NS
:Gri
nd
ing
an
d f
inis
hin
g w
orm
cu
tters
on
th
e f
ace
s (m
ore
info
rma
tion
pa
ge
617)
0.0
D
W
X
H*
T
E
Ite
m N
o.
13
81
25
4
2
3
2
18
22-1000
.51
2
.35
44
.92
1
.15
7
.31
5
.07
9
1.2
6
51
3
32
8
12
2
5
13
16
9
15
0
18
22-1001
.31
5
.47
2
.63
2
.0.1
18
1
.26
.5
12
.3
54
8
51
12
3
3
2
16
16
2
5
12
1
8
22-1002
.31
5
.47
2
.63
.1
18
2
.01
.26
.6
3
.47
2
16
4
0
3
32
25
25
0
1.2
6.6
3
1.5
75
.1
18
40
3
30
0
1.5
75
.1
18
11
.81
51
2.0
76
2
0
14
1
8
22-1003
2.99
2
.78
7
.47
2
16
76
2
5
18
22·1004
.632
.99
2
.98
4
NO
TE
: A
ll d
ime
ns
ion
s in
th
e t
ab
le i
n M
ilim
ete
rs(m
m)
for
refe
ren
ce in
che
s C'
) d
ime
ns
ion
s in
bo
ld ty
pe
.
Ex
am
ple
ho
w t
o o
rde
r:
Ite
m N
o.
Ty
pe
wh
ee
l o
r to
ol
W
H
Dia
mo
nd
Co
nc
en
tra
tio
n (
se
e p
ag
e 9
.)
22-1000
1209
x
4
x 32
x
50
*An
oth
er
siz
e o
f a
rbo
r (H
) a
s r
eq
uir
ed
. O
rde
r fo
rm s
ee
pa
ge
42
.
Angle Periphery
14EE1X Straight Face Diamond in
APPLICATIONS: Profile grinding. Internal and external thread cutting and grinding. Carbide tool fluting (more information page 617)
D • Wheel Diameter T Wheel Thickness -H Arbor-X Diamond Depth -b Diamond Thickness -E Back Thickness -0.0_ Angle
D b X 0.0 T H* Item No.
125 4.92
3 .118
4 .157 55
60 120 6 .236
32 1.26 23-1000
150 5.91
3 .118
3 .118
90
6 .236
8 .315
32 1.26
23-1001
3 .118
4 .157 60 23-1002
3 .118
5 .197
5 .197
5 .197
5 .197
3 .118
4 .157
5 .197
45
45
90
23-1003
23-1004
23-1005
23-1006
250 9.84
4 .157
6 .236
3 .118
90
15 .591
8 .315
76 2.992
23-1007
4 .157
4 .157
6 .236
6 .236
4 .157
5 .197
45
60 23-1008
23-1009
23-1010
23-1011
4 .157
6 .236
5 .197 55
4 .157
6 .236
5 .197 60
300 11.81
4 .157
6 .236
5 .197
5 .197
55
55
60
60 10
.394 127
5.00
23-1012
23-1013
350
4 .157
5 .197 55 60
10 .394
15 .591
127 5.00 160 6.3 203
7.992
23-1014
4 .157
6 .236
6 .236
5 .197
5 .197
55
45
60 23-1015
23-1016
4 .157
6 .236
4 .157
60 23-1017
NOTE: All dimensions in the table in Milimeters(mm) for reference inches C') dimensions in bold type.
Example how to order: Item No. Type wheel or tool b H 0.0 Diamond Concentration(see page 9.) 23-1000 14EE1X x 3 x 32 x 55 x 50
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
Angle Periphery
D • Wheel Diameter 1EE1X T - Wheel Thickness H ArborStraight Face -X • Diamond Depth Diamond in On - Angle
APPLICATIONS: Profile grindin9. Intemal and external thread cutting and
grinding. Carbide tool fluting (more information see page 6/7)
0 T X n ° H* Item No.
50
1.97
10
.394
5
.197
10
.394 120
15
.591 24-1000
80
3.15
8
.315
8
.315
5
.197
10
.394
90 110 125
120
15
.591
24-1001
24-1002
100
3.94
8
.315
10
.394
5
.197
5
10 45 .394
10
.394 90
120
110
42
1.654
24-1003
24-1004
10
.394
12
.472
5
.197
10
.394
90 110
120
120
24-1005
24-1006
24-100714
.551
16
.63
5
.197 145
125
4.92
150
5.91
8
.315
8
.315
5
.197
5
197 110
120
125
42
1.654
42
1.654
24-1008
24-1009
24-1010
24-1011
10
.394
10
.394
5
.197
10
.394
90 110
90
120
120
12
.472
16
.63
5
.197
5
.197 90
120 24-1012
24-1013
200
7.87
10
.394
10
.394 120
42
1.654
24-1014
12
.472
14
.551
10
.394
10
.394
90
120
24-1015
24-1016 16
.63
14
.551
5
.197 110 24 .. 1017
250
10
.394 5
.197 90 115 130
42
1.654
24-1018
12
.472
20
.787
5
.197
10
.394
120
120
24-1019
24-1020
14
.551 90 24-1021
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type. ° Example how to order: Item No. Type wheel or tool T X H n Diamond Concentration(see page 9.)
24-1000 1 EE 1 X x 10 x 5 x 15 x 120 *Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 M toliMfree (800) 618M7512 - faxMfree(800) 603-7374 - tel (310) 915-1111
.157
2.0
o - Wheel Diameter T - Wheel Thickness
H • Arbor(Hole Diameter) 1FF1X X - Diamond Depth
Straight Face Radius R Radius on Face -Diamond in Periphery
o
" ., ,
APPLICATIONS: Grinding concave wood milling cutters, form grinding, fluting (more information pages 6/7).
0 T X R H* Item No .. 0 T X R H* Item No.
50 12 10 11.0 15 25-1000 10 4 5.0 25 .. 1018 1.97 .472 .394 .433 .591 .394 .157 .197
3 4 1.5 25·1001 12 5 6.0 25-1019
80 .118 .059
125 .472 .197 .236
32
3.15 4
25-1002 4.92 16 5 8.0
1.26 25-1020.157 .63 .197 .315
5 4 2.5 20 45 20 6 10.0
.197 .157 .098 .787 1.772 25-1003
.787 .236 .394 25-1021
6 4 3.0 25·1004
18 10 11.0 25-1022
.236 .157 .118 .109 .394 .433
8 4 4.0 25-1005
18 10 20.0 42 25-1023.315 .157 .157 .109 .394 .787 1.654
85 22 5 15.0 42 25-1006 20 5 20.0 25-1024
3.346 .866 .197 .591 1.654 150
.787 .197 .787
8 4 4.0 25-1007 5.91
20 6 10.0 25-1025
.315 .157 .157 20 32
.787 .236 .394
10 4 5.0 .787 1.26 25-1008
24 7 12.0 32 51 25-1026.394 .157 .197 .945 .276 .472 1.26 2.0
10 10 20.0 42 25-1009 32 7 16.0 25-1027 .394 .394 .787 1.654 1.26 .276 .63
100 12 5 6.0 20 32 25-1010 175 32 5 20.0 42
25-1028 3.94 .472 197 .236 .787 1.26 6.89 1.26 .197 .787
1.654
20 5 20.0 25-1011 10 10
7.0 25-1029
.787 .197 .787 .394 .394 .276
24 5 15.0 42 200
20 5 10.0 42 25-1030
.945 .197 .591 25-1012 .787 .197 .394
30 5 15.0 1.654 7.87
30 5 1.654
1.181 .197 .591 25-1013
1.181 .197 .079 25-1031
3 4 1.5 25-1014
20 10 20.0 25-1032
.118 .157 .059 .787 .394 .787 250
5 45.0 42
4 4 2.0 25-1015
20 1.654 25-1033
.157 .157 .079 9.84
.787 .197 1.772 125
4 3.0 32
10 60.04.92
6 1.26 25-1016 30 25-1034
.236 .157 .118 300 1.181 .394 2.362
42 8 4 4.0 25-1017 11.81 30 10 900 1.654 25-1035
.315 .157 .157 1.181 .394 35.43
NOTE: All dimensions in the table in Milimeters(mm) for reference inches ( ) dimensions in bold type." Example how to order: Item No. Type wheel or tool H Diamond Concentration(see page 9.)
25-10000 1FF1X x 15 x 50
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
l')a
D - Wheel Diameter T - Wheel Thickness H - Arbor (Hole Diameter) X Diamond Depth -2FF6V R - Insert Raidus
Straigh Concave Radius h - Insert Height
Diamond Insert in Periphery
D
APPLICATIONS: Designed for machining industrial and windshield glasses (more information pages 6/7)
D T h R X H* Item No. D T h R X H* Item No.
11.0 .433
8.7
.343
3.0
.118
6.5
.256 27 ... 1000
.61
6.0
.236
4.0 .157
8.0
.315
60.00
2.362
27·1009
27-1010
27-1011
100 3.94
11.0 .433
11.0
.433
8.7
.343
8.7
.343
4.5 .177
6.0
.236
6.5
.256
.256
75
2.953 27-1001
27-1002
200
7.874
15.5 .61
15.5
.61
6.5
.256
7.0
.276
4.5
.177
5.0
.197
8.0
.315
8.0
.315
150 5.91
14.0 .551
14.0 .551
12.5
.492
8.6
.339
8.6
.339
9.0
.354
4.0
.157
6.0
.236
4.5
.177
6.5
.256
6.50
.256
8.0
.315
100
3.94
22
.866
27-1003
27-1004
27-1005 250
15.0 .591
15.0
.591
15 .0 .591
8.0
.315
6.0
.236
7.0
.276
4.0
.157
2.5
.098
3.2
.126
3.8
.15
6.0
.236
6.0
.236 1 7.53
27-1012
27-1013
27-1014
27-1015
27-1016
12.0 .472 .276
3.5
138
9.0
.354
50
1.969 27 ... 1006
9.843 15 .0 .591
10.0
.394
5.5
.217
6.0
.236
200
7.874
15.5
.61
15.5
.61
5.0
.197
5.5
.217
3.0
.118
.138
8.0
.315
8.0
.315
60
2.362
27·1007
27·1008
15 .0 .591
12.0 .472
7.0
.276 .236
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool H Diamond Concentration (see page 9.) 27-1000 2FF6V x 75 x 75
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 • toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
.236
.236 .236
1GG1V Straight Concave Radius
Diamond Insert in Periphery
D
D • Wheel Diameter T· Wheel Thickness
H • Arbor (Hole Diameter)
X • Diamond Depth
R - Insert Raidus
h Insert Height -
APPLICATIONS: Designed for machining industrial and windshield glasses (more information pages 617)
D T h R X H* Item No.
6
.236
7
.276
5
.197
6
2.5
.098
3.0
.118
5
.197
5
.197
60
2.36
60
2.36
28·1000
28·1001
8
.315
7
.276
3.7
.146
5
.197
60
2.36 28·1002
200
7.874
9
.354
10
.394
8
.315
6
.236
4.7
.187
2.5
.098
5
.197
6
.236
60
2.36
76
2.94
28·1003
28-1004
10
.394
6 3.0
.118
6 76
2.94 28·1005
10
.394
6
.236
3.7
.146
6
.236
76
2.94 28-1006
10
.394
8
.315
4.7
.185
6
.236
76
2.94 28-1007
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool H Diamond Concentration (see page 9.) 28-1000 1GG1V x 60 x 75
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
3.94
95
o Wheel Diameter -T Wheel Thickness -H Arbor (Hole Diameter) -1FF6V X • Diamond Depth R -Insert Raidus Straight Concave Radius h -Height on Concave Diamond Insert in Periphery
APPLICATIONS: Designed for machining industrial and windshield glasses (more information see page 6n)
T h R X
12 5.2 3.0 3.0
.472 .205 .118 .118
13 6.9 3.5 .512
15 .591
16 10.4 6.0 4.5 .63 .409 .236 .177
18 7.0 5.0 .709 .276 .197
20 8.0 5.5 .787 .315 .217
23 17.3 10.0 6.5 .906 .681 .394 .256
4.0 2.5 .157 .098
5.7
.224
6.4 .252
T h R X
16 8.0 7.2 .315 .283
10.0 8.7 .709 .394 .343
30 26.0 14.0 11.9 1.181 1.024 .469
12 5.2 3.0 3.0 .472 .205 .118 .118
13 6.9 4.0 3.5 .512 .272 .157 .138
15 8.7 5.0 4.0 .591 .197 .157
16 10.4 .63 .409
13.9 .547
0
3.740
H* Item No. 0 H* Item No.
26·1015
22 26·1016 .866
26-1017
26-1018
26-1019
26-1020 25
.984 26·1021
26·1022
26-1000
26-1001 100
26-1002
25 26-1003 .984
26-1004
26-1005
26-1006 175 6.89
26-1007
26·102326-1008
26·102426·1009
100 22 26·102526-1010 3.937 .866
26-1011 26-1026 60
26-1013 2.362 26-1027
26-1014 26-1028
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool H Diamond Concentration (see page 9.) 26-1000 1FF6V x 25 x 75
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
x
o Wheel Diameter . T· Wheel Thickness
H • Arbor (Hole Diameter) 6A2T X • Diamond Depth 01-Diameter
Straight Wheel d1 Bolt Holes Diamond on Top -h - Arbor Depth
o
APPLICATIONS: Glass faceting. Machining flat surfaces of carbide and ceramic pieces (more information pages 6/7)
0 X H* T 01 dl h Item No.
100 3.94
1.5
.059
3 .118
40 1.575
18 .709
70 2.756
M8 12 29-1000
.472
150 5.91
1.5 .059
3 .118
40 1.575
18
.709
70 2.756
M8 12 29-1001.472
200 7.874
1.5 .059
3 .118
80 3.15
18 .709
150 5.91
M8 12 29-1002.472
250 9.843
1 . 5 .059
3 .118
80 3.15
18 .709
150 5.91
M8 12 .472 29-1003
300 11.811
1.5 .059
3 .118
80 3.15
20 .787
260 10.24
M10 14 .551
29-1004
400 15.75
1.5 .059
3 .118
80 3.15
20 .787
260 10.24
M10 14 29-1005.551
NOTE: All dimensions in the table in Milimeters(mm) for reference inches C') dimensions in bold type. Example how to order: Item No. Type wheel or tool H Diamond Concentration(see page 6n)
29-1000 6A2T x 40 x 50
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
.... ....
D • Wheel Diameter T· Wheel Thickness H • Arbor (Hole Diameter) X - Diamond Depth
1A1R T
Cut-oft-Steel Center E - Core Thickness Diamond in Periphery
H*
D
APPLICATIONS: Cutting hard and brittle nonmetallic materials: glass, quartz, fused and pressed ceramics, semiconducting materials, corundum, natural and synthetic semiprecious and job stones ( more information page 6/7)
D T X E D T X E H* Item No.
0.6 5.0 0.4 1.2 5.0 0.9 30-1012 .023 .197 .016 .197 .035
0.8 5.0 0.6 5.0 1.2100 20 30-1001 30-1013.031 .197 .023 .197 .0473.94 32.787 200 1.0 5.0 0.8 2.0 5.0 1.6 1.267.8430-1002 30-1014
.039 .197 .031 .078 .197 .063
0.8 5.0 0.6 2.2 5.0 1.830-1003 30-1015.197 .197.031 .023 .087 .071
125 1.0 5.0 0.8 2.0 5.0 1.632 30-1004 30-1016
4.92 .039 .197 .031 .078 .197 .0631.26 250 32
1.2 0.9 1.89.84 1.2630-1005 30-1017.047 .035 .071 0.8 0.6 300 1.8 7630-1006 30-1018
.031 .197 .023 11.81 .197 .071 2.99
1.0 0.8 30-1007 30-1019 .039 .031 320150 32
12.65.91 1.26 30-1009 30-1020
30-1009 30-1021
30-1010 30-1022 175 32
6.89 1.26 30-1011 30-1023
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool E H Diamond Concentration(see page 9.) 30-1000 1A1R x 0.4 x 20 x 25
*Another size of arbor (H) as required. Order form see page 42.
1 1869 Teale Street, Culver City, CA 90230 - toll-free (800) 6 18-75 12 - fax-free(800) 603-7374 - tel (310) 9 15- 1 1 1 1
...
D - Wheel Diameter T - Wheel Thickness H - Arbor (Hole Diameter) X - Rim Depth
1 2A2 -45 D B (two-layer) Flaring Double Rim W1 - Rim Width Cup Diamond in Rim
W2 - Rim Width
D
W2W1
APPLICATIONS: Carbide and tool steel cutter grinding and sharpening (more information pages 617)
D W1 W2 X T H* Item No.
100
3.94
3
.118
2
0.79
3
.118
32
1.26
20
.787 31-1000
125
4.92
3
.118
2
0.79
5
.197
34
1.339
20
.787 31-1001
125
4.92
3
.118
2
0.79
3
.118
40
1.575
32
1.26 31-1002
125
4.92
5
.197
5
.197
3
.118
40
1.575
32
1.26 31-1003
125
4.92
3
.118
2
0.79
5
.197
42
1.654
32
1.26 31-1004
125
4.92
5
.197
5
.197
5
.197
42
1.654
32
1.26 31-1005
150
5.91
5
.197
5
.197
3
.118
40
1.575
32
1.26 31-1006
150
5.91
5
.197
5
.197
5
.197
42
1.654
32
1.26 31-1007
200
7.87
10
.394
10
.394
3
.118
50
1.969
76
2.99 31-1008
200
7.87
10
.394
10
.394
5
.197
52
2.05
76
2.99 31-1009
200
7.87
10
.394
10
.394
3
.118
50
1.969
76
2.99 31-1010
200
7.87
10
.394
10
.394
5
.197
52
2.05
76
2.99 31-1011
NOTE: All dimensions in the table in Milimeters(rnm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool H Diamond Concentration(see page 9.) 31-1000 12A2-45DB x 20 x 50
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
D - Wheel Diameter T - Wheel Thickness 12A2 -20 DB (two-layer) H - Arbor (Hole Diameter) X Rim Depth
Double Rim Dish Wheel -
W1 - Rim Width Diamond in Rim W2 - Rim Width
D
APPLICA-nONS: Facing carbide saw blades (more information pages 6/7)
D W1 W2 X T H* Item No.
125 4.92
3 .118
3 .118
1.5 .059
12 .472
32 1.26
32-1000
125 4.92
3 .118
3 .118
3.0 .118
14 .551
32 1.26
32-1001
NOTE: All dimensions in the table in Milimeters(mm) for reference inches ( ) dimensions in bold type."
Example how to order: Item No. Type wheel or tool H Diamond Concentration (see page 9.) 32-1000 12A2-20DB x 32 x 50
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
D • Wheel Diameter T· Wheel Thickness H • Arbor (Hole Diameter) X • Diamond Depth
12M2 -45 D
Dish Wheel W1 - Rim Width W2W1Diamond in Rim W2 Rim Width -
T
H*
APPLICATIONS: Sharpennig carbide saw blades on the flanks and faces (more information pages 617)
D W1 W2 X T H* Item No.
125
4.92
2.5
.098
2.5
.098
6
.236
18
.709
32
1.26 33·1000
125
4.92
3.0
.118
3.0
.118
6
.236
18
.709
32
1.26 33·1001
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool H Diamond Concentration(see page 9.) 33-1000 12M2-45 x 32 x 50
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
Angle Periphery
D • Wheel Diameter T· Wheel Thickness
H· Arbor (Hole Diameter) 1V1 X • Diamond Depth
Straight Face (1..0 - Angle
Diamond in
APPLICATIONS:Grinding and electrochemical chip grooving of carbide rotary (more infromation pages 617)
D X T (1..0 H* Item No.
80
3.15
5
.197
6
.236
15 25
.984 34-1000
100
3.94
5
.197
8
.315
15 32
1.26 34-1001
125
4.92
5
.197
10
.394
15 32
1.26 34-1002
125
4.92
5
.197
10
.394
35 32
1.26 34·1003
200
7.81
5
.197
6
.236
35 76
2.99 34-1004
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool H Diamond Concentration (see page 9.) 34-1000 1V1 x 25 x 75
* Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
D - Wheel Diameter T - Wheel Thickness A1PP H Arbor (Hole Diameter) -
Straight Wheel Diamond Throughout
D
APPLICATIONS:Grooving ferrite parts of magnetic heads, articles made of ceramics, glass, special heat-resistant and nonmetallic materials (more information page 6/7)
D T H* Item No.
50
1.969
0.15
.00591
0.30
.01181
0.45
.01772
0.60
.02362
0.80
.03150
1.00
.03937
1.20
.04724
1.60
06299
2.00
.07874
2.40
.09449
12
.04724 35-1000
80
3.15
0.15
.00591
0.30
.01181
0.45
.01772
0.60
.02362
0.80
.03150
1.00
.03937
1.20
.04724
1.60
06299
2.00
.07874
2.40
.09449
20
.7874 35-1001
100
3.94
0.15
.00591
0.30
.01181
0.45
.01772
0.60
.02362
0.80
.03150
1.00
.03937
1.20
.04724
1.60
06299
2.00
.07874
2.40
.09449
32
1.26 35-1002
NOTE: All dimensions in the table in Milimeters(mm) for reference inches (") dimensions in bold type.
Example how to order: Item No. Type wheel or tool T H Diamond Concentration(see page 9.) 35-1000 A1PP x 0.15 x 12 x 75
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
grinding materials
D Wheel Diameter T Wheel Thickness -H Arbor (Hole Diameter) -AOKF
-
Straight Wheel Diamond Throughout
D
APPLICATIONS:Cutting and polycore, quartz, ferrites and other h ard and brittle nonmetallic (more information pages 6/7)
D T H* Item No.
50
1.969
0.03
.00012
0.05
.002
0.07
.003
0.09
.0035
0.11
.0043
0.13
.0051
12
.472
40
.1575 36-1000
56
2.2
0.03
.00012
0.05
.002
0.07
.003
0.09
.0035
0.11
.0043
0.13
.0051
40
.1575 36-1001
75
2.953
0.03
.00012
0.05
.002
0.07
.003
0.09
.0035
0.11 .0043
0.13
.0051
60
2.36 36-1002
76
2.99
0.05
.002
0.07
.003
0.09
.0035
0.11 .0043
0.13
.0051 13
.512 36-1003
76
2.99
80
3.15
0.03
.00012
0.05
.002
0.07
.003
0.07
.003
0.09
.0035
0.09
.0035
0.11
.0043
0.11
.0043
0.13
.0051
0.13
.0051
40
.1575
20
.787
36-1004
36-1005
100
3.94
0.07
.003
0.09
.0035
0. 11 .0043
0.13
.0051
32
1.26 36-1006
NOTE: All dimensions in the table in Milimeters(mm) for reference inches C') dimensions in bold type.
Example how to order: Item No. Type wheel or tool T H Diamond Concentrataion(see page 9.) 36-1000 AOKF x 0.03 x 12 x 75
*Another size of arbor (H) as required. Order form see page 42.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111
'--____________ .....
..... ______ .....;°"--________ .1
---11>1 11 1..-per cut, and quality smooth cutting
7"
7" (1n.8mm) .059" (1.5mm)
8" (203.2mm) .059" (1.5mm)
9" (228.6mm) .059" (1.5mm)
10" (254mm) .087" (2.2mm)
Who uses Monster II
Monster II Premium blades are for users who need medium to large
1 jobs, maximum production, low cost
Item No.
.196" (5mm) 5/8" (1S.87mm)
.196" (Smm) 5/8" (1S.87mm)
.196" (Smm) 5/8" (1S.87mm)
.196" (Smm) 5/8" (1S.87mm)
93-2002
93-2003 &
93-2004 &
93-2005
93-2006 &
Application Specification
Monster II Premium - Quality & maximum production for cutting a wide variety of ceramic tile, quarry tile,
glass, quartz fused, ceramics, slate, semiconducting
materials, corundum, natural and synthetic semi
t T of a wide variety of hard materials precious stones, terrazo, granite and marble .6. stock items - other sizes are special order only
11 Diamond blade cutting depth 6" 1-314 6,048 10,185 will vary.
2-1/4" 5,184 8,730
811 2-31411 4,536
911 3-1/411 4,032
10" 3-31411 3,629
*Based on 9.500 SFPM (Surface Feet Per Minute)
• For stone and tile, the optimum performance speed is 10-2S% less than the speed
shown above in the table.
• For most tools, blade shaft speed will be higher than the recommended operating
speed shown (above) in the table (RPM's at no load).
• The actual blade shaft speed or tool will slow down under10ad and usually should
fall within the optimum speed range.
·The maximun safe speed RPM(in revolutions per minute) each table can be used.
• Make sure before using any blade: shaft(arbor) of the blade or the tools is within
the 'maximum safe speed limit'.
It depends on: 7,640 • Blade diameter
6,790 • Saw type (brand) • Diameter of the blade
6,115 flanges
Water Cooled • Keeping your diamond blade cool and extend its life and
improve its performance, reduce dust, remove cutting.
• Wet cutting diamond blades must be used with a continuous
water flow to prevent heat build-up, damage and hazard during
cutting.
• Check the saw or tool before using a wet cutting diamond
blade.
• Make sure it is safe to use the saw or tool with water.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111 - fax (310) 390-5793
"'"-------------......
I .... ______ D"'--_____ ..... .,.I
•
5/8" (15.87mm)
6"
7"
Item No.
93-2012
8" (1n.8mm) .06S" (1.65mm) •375" (9.525mm) 1" (25.4mm) 93-2013
8" (203.2mm) .065" (1.65mm) .375" (9.525mm) 93-2014 ..
9" (228.6mm) .065" (1.65mm) • 375" (9.525mm) 5/8" (15.87mm) 93-2015
10" (254mm) .065" (1.65mm) .375" 5/8" (15.87mm) 93-2016 •
Who uses Monster II Application Specification
Monster II Super Premium blades Monster II Super Premium - Quality & maximum are for users who need maximum production for cutting a wide variety of ceramic tile,
production, low cost per cut, and quarry tile, glass, quartz fused, ceramics, slate,
-+1 I.ort- H w-+I I+- quality smooth cutting of a wide semiconducting materials, corundum, natural and variety of hard materials synthetic semi-precious stones, terrazo, granite and
.. stock items • other sizes are special order only marble
Diamond blade cutting depth 1-3/4" 6,048 10,185 will vary.
2 .. 1/4" 5,184 8,730 It depends on: 8" 2 .. 3/4" 4,536 7,640
9" 3-1/4" 4,032 • Blade diameter
6,790
10" 3-3/411 3,629 6,115
• Saw type (brand)
• Diameter of the blade
flanges
*Based on 9.500 SFPM (Surface Feet Per Minute)
• For stone and tile, the optimum performance speed is 10-25% less than the speed
shown above in the table.
• For most tools, blade shaft speed will be higher than the recommended operating
speed shown(above) in the table (RPM's at no load).
• The actual blade shaft speed or tool will slow down underload and usually should
fall within the optimum speed range.
-The maximun safe speed RPM(in revolutions per minute) each table can be used.
• Make sure before using any blade: shaft(arbor) of the blade or the tools is within
the -maximum safe speed limit-.
Water Cooled
• Keeping your diamond blade cool and extend its life and
improve its performance, reduce dust, remove cutting.
• Wet cutting diamond blades must be used with a continuous water flow to prevent heat build-up, damage and hazard during
cutting.
• Check the saw or tool before using a wet cutting diamond
blade.
• Make sure it is safe to use the saw or tool with water.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111 - fax (310) 390-5793
..... _____________ ...1
11 0 !;. ------------ -----------. ! __ .... ..
5/8" (15.87mm)
6"
9"
Item No.
93-2012
8" (1n.8mm) .0651t(1.65mm) .375" (9.525mm) 1" (25.4mm) 93-2013 A
8" (203.2mm) .065"(1.65mm) .375" (9.525mm) 93-2014 A
9" (228.6mm) .065"(1.65mm)
1011 (254mm) .065" (1.65mm)
Who uses Monster II
Monster II Standard blades are for users who need maximum production, low cost per cut, and
t T -.! !...- H W-'! !...- quality smooth cutting of a wide variety of hard materials
• stock items - other sizes are special order only
.375" (9.525mm) 5/811 (15.87mm) 93-2015
.375" 5/811 (15.87mm) 93-2016 •
Application Specification
Monster II Standard - Quality & maximum production for cutting a wide variety of ceramic tile, quarry tile, glass, quartz fused, ceramics, slate, semiconducting materials, corundum, natural and synthetic semiprecious stones, terrazo, granite and marble
Diamond blade cutting depth 1-31411 6,048 10,185 will vary.
7" 2-1/4" 5,184 8,730
H depends on: 81t 2-314" 4,536 7,640 • Blade diameter
3-1/4" 4,032 6,790 • Saw type (brand)
• Diameter of the blade 10" 3-3/4" 3,629
*Based on 9.500 SFPM (Surface Feet Per Minute)
- For stone and tile, the optimum performance speed is 10-25% less than the speed shown above in the table. - For most tools, blade shaft speed will be higher than the recommended operating speed shown(above) in the table (RPM's at no load). - The actual blade shaft speed or tool will slow down underload and usually should fall within the optimum speed range. -The maxim un safe speed RPM(in revolutions per minute) each table can be used. - Make sure before using any blade: shaft(arbor) of the blade or the tools is within the "maximum safe speed limit".
6,115 flanges
Water Cooled - Keeping your diamond blade cool and extend its life and
improve its performance, reduce dust, remove cutting.
- Wet cutting diamond blades must be used with a continuous
water flow to prevent heat build-up, damage and hazard during
cutting.
- Check the saw or tool before using a wet cutting diamond
blade.
- Make sure it is safe to use the saw or tool with water.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111 - fax (310) 390-5793
..... ______________ .....
6"
2-3/4"
8" (1n.8mm) .06511(1.65mm)
10" (254mm) .065"(1.65mm)
Who uses Monster II
Monster II Super Premium Plus
blades are for users who n eed
maximum production, low cost per
cut, and quality smooth cutting of a
wide variety of hard materials
Item No.
93-3002
.375" (9.525mm) 5/8" (15.87mm) 93-3004
.375" (9.525mm) 5/8" (15.87mm) 93-3006
Application Specification
Monster II Super Premium Plus - Quality & maximum
production for super fast cutting a wide variety of hard
tile, procelam, granite and marble.
Diamond blade cutting depth 1-3/411
10" 3-3/411 3,629 6,115
6,048 10,185 will vary.
4,536 7,640
It depends on:
*8ased on 9.500 SFPM (Surface Feet Per Minute)
- For stone and tile, the optimum perfonnance speed is 10-25% less than the speed
shown above in the table.
- For most tools, blade shaft speed will be higher than the recommended operating
speed shown(above) in the table (RPM's at no load).
- The actual blade shaft speed or tool will slow down underioad and usually should
fall within the optimum speed range.
-The maximun safe speed RPM(in revolutions per minute} each table can be used.
- Make sure before using any blade: shaft(arbor) of the blade or the tools is within
the "maximum safe speed limit".
• Blade diameter • Saw type (brand) • Diameter of the blade
flanges
Water Cooled - Keeping your diamond blade cool and extend its life and
improve its perfonnancs, reduce dust, remove cutting.
- Wet cutting diamond blades must be used with a continuous
water flow to prevent heat build-up, damage and hazard during
cutting.
- Check the saw or tool before using a wet cutting diamond
blade.
- Make sure it is safe to use the saw or tool with water.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111 - fax (310) 390-5793
r-----------------------------�
1 I .. _____ ----.i.m ;' -..1 1..- w-.. I 1..-
.... ---------------------------.....
Rim
t
0
H
. OS9" (1.Smm)
7" (1n.8mm) .OS9" (1.Smm)
8" (203.2mm) .059" (1.Smm)
911 (228.6mm) .059" (1.Smm)
10" (254mm) .087" (2.2mm)
Who uses Monster I Monster I Premium blades are for
users who need medium to large
jobs, maximum production, low cost
per cut, and quality smooth cutting
of a wide variety of hard materials
• stock items - other sizes are special on:ter only
Item No •
.196" (Smm)
.196" (Smm)
.196" (Smm)
.196"
518" (1S.87mm)
518" (1S.87mm)
S/811 (1S.87mm)
S/8" (1S.87mm)
93-2002
93-2003 •
93-2004 A
93-200S
93-2006 •
Application Specification Monster I Premium - Quality & maximum production
for cutting a wide variety of ceramic tile, quarry tile,
glass, quartz fused, ceramics, slate, semiconducting
materials, corundum, natural and synthetic semi
precious stones, terrazo, and marble
6" 1-314" 6,048
7" 2-1/4" S,184
811 2-3/4" 4,536
9" 3-1/4" 4,032
1011 3-314" 3,629
*Based on 9.S00 SFPM (Surface Feet Per Minute) • For stone and tile, the optimum perionnance speed is 10-2S% less than the speed
shown above in the table.
• For most tools, blade shaft speed will be higher than the recommended operating
speed shown (above) in the table (RPM's at no load).
- The actual blade shaft speed or tool will slow down under10ad and usually should
fall within the optimum speed range.
-The maximun safe speed RPM(in revolutions per minute) each table can be used.
- Make sure before using any blade: shaft(arbor) of the blade or the tools is within
the 'maximum safe speed limit-.
10,185
8,730
7,640
6,790
6,11S
Diamond blade cutting depth
will vary.
It depends on:
• Blade diameter
• Saw type (brand)
• Diameter of the blade
flanges
Water Cooled - Keeping your diamond blade cool and extend its life and
improve its perfonnance, reduce dust, remove cutting.
• Wet cutting diamond blades must be used with a continuous
water flow to prevent heat build-up, damage and hazard during
cutting.
• Check the saw or tool before using a wet cutting diamond
blade.
• Make sure it is safe to use the saw or tool with water.
11869 Teale Street, Culver City, CA 90230 - toll·free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915·1111 - fax (310) 390-5793
__________ D __________ I I
tr .... ---------------..
W---" 1 1.-
Item No.
93-2002
7" (1n.8mm) .059" (1.Smm) . 196" (Smm) 5/8" (1S.87mm) 93-2003 ...
8" (203.2mm) .059" (1.Smm) .196" (Smm) 5/8" (1S.87mm) 93-2004 A
911 (228.6mm) .059" (1.Smm) .19611 (Smm) 5/8" (1S.87mm) 93-2005
1011 (254mm) .087" (2.2mm) .196" (Smm) 5/811 (1S.87mm) 93-2006 A
Who uses Monster I Application Specification
Monster I Super Premium blades Monster I Super Premium • Quality & maximum are for users who need , maximum production for cutting a wide variety of ceramic tile,
production, low cost per cut, and quarry tile, glass, quartz fused, ceramics, slate,
quality smooth cutting of a wide semiconducting materials, corundum, natural and
variety of hard materials synthetic semi-precious stones, terrazo, and marble
... stock items· other sizes are special order only
6" 1-3/4" 6,048
7" 2-1/4" 5,184
8" 2-314" 4,536
9" 3-1/4" 4,032
10" 3-3/411 3,629
*8ased on 9.500 SFPM (Surface Feet Per Minute)
• For stone and tile, the optimum perfonnance speed is 10-2S% less than the speed
shown above in the table.
• For most tools, blade shaft speed will be higher than the recommended operating
speed shown(above) in the table (RPM's at no load).
• The actual blade shaft speed or tool will slow down under10ad and usually should
fall within the optimum speed range .
•The maximun safe speed RPM(in revolutions per minute) each table can be used.
• Make sure before using any blade: shaft(arbor) of the blade or the tools is within
the 'maximum safe speed limit'.
Diamond blade cutting depth 10,185 will vary.
8,730
It depends on: 7,640
• Blade diameter
6,790 • Saw type (brand)
• Diameter of the blade
6,115 flanges
Water Cooled • Keeping your diamond blade cool and extend its life and
improve its perfonnance, reduce dust, remove cutting.
• Wet cutting diamond blades must be used with a continuous
water flow to prevent heat build-up, damage and hazard during
cutting.
• Check the saw or tool before using a wet cutting diamond
blade.
• Make sure it is safe to use the saw or tool with water.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111 - fax (310) 390-5793
..... ------------......
�----------------------------� , .. + .t __ . __ .. _____ ...
-.1 1.- w-.I 1.-..... ------------------.....
3-3/4"
.196" (Smm)
Item No.
23-4672
6" (1S2.4mm) .020"(.508mm) .196" (Smm) 1/2" (12.7mm) .012" (.30Smm) 23-4673
6" (152.4mm) .020"(.508mm) .196"(Smm) 5/S" (1S.87mm) .012" (.30Smm) 23-4674
6" (1S2.4mm) .032"(·813mm) SiSti (1S.87mm) .025"(·63Smm) 23-4710
10"(250.4mm) .032"(·813mm) .196"(Smm) SIS"(1S.87mm) .025"(.63Smm) 23-4711
Who uses Monster VII Application Specification
Monster VII Premium blades are for Monster VII Premium - Quality & maximum production
D users who need medium to large for cutting a wide variety of semi-precious and precious
jobs, maximum production, low cost stones.
t T t s H per cut, and quality smooth cutting of a wide variety of hard materials
Diamond blade cutting depth 6,04S 10,1S5 will vary.
10" 3,629 6,115
It depends on:
• Blade diameter • Saw type (brand) • Diameter of the blade
flanges
Water Cooled *8ased on 9.500 SFPM (Surface Feet Per Minute) •• For stone and tile, the optimum performance speed is 10-2S% less than the speed Keeping your diamond blade cool and extend its life and
shown above in the table. improve its performance, reduce dust, remove cutting.
• For most tools, blade shaft speed will be higher than the recommended operating - Wet cutting diamond blades must be used with a continuous
speed shown(above) in the table (RPM's at no load). water flow to prevent heat build-up, damage and hazard during • The actual blade shaft speed or tool will slow down underioad and usually should cutting.
fall within the optimum speed range. Check the saw or tool before using a wet cutting diamond •
-The maximun safe speed RPM(in revolutions per minute) each table can be used. blade.
• Make sure before using any blade: shaft(arbor) of the blade or the tools is within • Make sure it is safe to use the saw or tool with water.
the "maximum safe speed limit'.
11869 Teale Street, Culver City, CA 90230 - toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111 - fax (310) 390-5793
...-_______________ ....
..... ______ ______ --t.1 m!
4"
14" 5"
14" (177.8mm) .095" (2.4mm)
Who uses Monster II
Monster II Super Premium blades fast and are for users who need
maximum production, low cost per
cut, and quality smooth cutting of a
wide variety of hard materials on
1 D masonry or stone saws
Item No.
1" 93-6012
.196" (5mm) 111 (25.4mm) 93-6013
Application Specification
Monster II Super Premium - Quality & maximum production for cutting a wide variety of hard ceramic
tile, quarry tile, granite and marble and porcelin. Do
not use for cutting brick or block
12" Diamond blade cutting depth 3,024 5,095 will vary.
2,592 4,365 It depends on:
• Blade diameter
• Saw type (brand)
• Diameter of the blade
flanges
ct Water Cooled *8ased on 9.500 SFPM (Surface Feet Per Minute) - For stone and tile, the optimum performance speed is 10-25% less than the speed
shown above in the table.
- For most tools, blade shaft speed will be higher than the recommended operating
speed shown(above) in the table (RPM's at no load).
• The actual blade shaft speed or tool will slow down underload and usually should
fall within the optimum speed range.
·-The maximun safe speed RPM(in revolutions per minute) each table can be used.
• Make sure before using any blade: shaft(arbor) of the blade or the tools is within
the "maximum safe speed limit".
- Keeping your diamond blade cool and extend its life and
improve its performance, reduce dust, remove cutting.
- Wet cutting diamond blades must be used with a continuous
water flow to prevent heat build-up, damage and hazard during
cutting.
• Check the saw or tool before using a wet cutting diamond
blade .
• Make sure it is safe to use the saw or tool with water.
Strr;et, Culver City. CA 90230· toll-free (800) 618-7512 - fax-free(800) 603-7374 - tel (310) 915-1111 - fax (310) 390-5793
..... _______________ ... .... ------0-------t..1 1 masonry or stone saws
4"
14"(1n.8mm) .095" (2.4mm)
Who uses Monster II Monster II Super Premium blades fast and are for users who need maximum production, low cost per cut, and quality smooth cutting of a wide variety of hard materials on
Item No.
93-6012
.196" (5mm) 11• (25.4mm) 93-6013
Application Specification Monster II Super Premium - Quality & maximum production for cutting a wide variety of hard ceramic tile, quarry tile, granite and marble and porcelin. Do not use for cutting brick or block
1t T -+ I+- H w-+I I+-
12" Diamond blade cutting depth 3,024 5,095
14" 5" 2,592
*Based on 9.500 SFPM (Surface Feet Per Minute) - For stone and tile, the optimum performance speed is 10-25% less than the speed
shown above in the table.
- For most tools, blade shaft speed will be higher than the recommended operating
speed shown (above) in the table (RPM's at no load).
- The actual blade shaft speed or tool will slow down underload and usually should
fall within the optimum speed range.
-The maximun safe speed RPM(in revolutions per minute) each table can be used.
• Make sure before using any blade: shaft(arbor) of the blade or the tools is within the "maximum safe speed limit".
will vary. 4,365
It depends on:
• Blade diameter
• Saw type (brand)
• Diameter of the blade
flanges
..... _______________ ..
I""" __