Post on 16-Apr-2022
Machinery
FO
RA
NO
CH
IP S
CR
EE
NForano Chip ScreenModels CS-25, CS-26, CS-28, CS-30, CS-32
Excellent PerformanceUp to 50% faster rotary speed results in better material agitation. That means you get improved separation, especially for small chips.
Reliable OperationVery few moving parts to wear out. This is low-maintenance you can count on!
Easy InstallationJust drop the Forano Chip Screen in place and let it go to work. A wide range of standard discharge spouts makes it easy to integrate with other equipment in your mill.
USNR’s Forano Chip Screen is a high capacity screen that allows your mill to take advantage of an important source of income: wood chips. The Forano Chip Screen requires minimal maintenance, so you can spend your time and budget elsewhere.
Debarkers
Primary Breakdown
Secondary Breakdown
Lumber Handling
Planing Systems
Residual Processing
MA-46-E 200812 ©USNR
800.BUY.USNR WWW.USNR.COM
Oscillation System
► Dual heavy steel counter-weights are held in place by maintenance
free (pre-packed with grease) double taper roller unit encased in a
steel housing (2” diameter throw)
► Electric motor drive (1800 RPM)
► Main shaft is CNC-machined from 7” or 8” diameter 1045 steel
Super Chip Screen
Frame and Basket
► Welded structure made from high-strength 6”x 6” or 8”x 8” steel
tubing and 44W steel plate
► Basket balanced laterally and longitudally
► Basket hangs at a 7° angle from four hanger assemblies using
“heavy equipment” rated univeral joints
► Standard 2”x 2” square screen holes – other round and square
screen sizes available
D A
E
F
G
C
B30"
FLOW
A X B C D E F G HP WEIGHT CAP. (1)
4 X 10 7′ 0” 6′ 8” 12′ 7” 92 1/2” 44” 5 10,100 lb 15
4 X 12 9′ 0” 6′ 8” 14′ 6 3/4” 92 1/2” 44” 5 10,500 lb 19
5 X 10 7′ 0” 7′ 10” 12′ 7” 92 1/2” 44” 5 10,600 lb 21
6 X 10 7′ 0” 8′ 0” 12′ 7” 92 1/2” 44” 7.5 11,300 lb 24
6 X 12 9′ 0” 8′ 8” 14′ 6 3/4” 92 1/2” 44” 7.5 11,900 lb 28
7 X 14 10′ 0” 9′ 8” 16′ 6 5/8” 92 1/2” 44” 7.5 13,000 lb 40
8 X 12 9′ 0” 10′ 8” 14′ 6 3/4” 92 1/2” 44” 10 13,000 lb 40
8 X 14 10′ 0” 10′ 8” 16′ 6 5/8” 92 1/2” 44” 10 13,600 lb 48
8 X 16 11′ 0” 10′ 8” 18′ 6 1/2” 92 1/2” 44” 10 14,100 lb 54
9 X 12 9′ 0” 11′ 8” 14′ 6 3/4” 92 1/2” 44” 10 13,600 lb 44
10 X 16 12′ 0” 13′ 0” 18′ 6 1/2” 93 3/4” 52” 15 19,700 lb 64
10 X 18 14′ 0” 13′ 0” 20′ 6 1/4” 93 3/4” 52” 15 20,300 lb 72
10 X 20 14′ 0” 13′ 0” 22′ 6 1/8” 93 3/4” 52” 15 20,800 lb 86
(1) Capacities are in units per hour, and are based on 300 RPM with 2” square per forated top screens.
One unit=200 cu. f t (5.66 cu. meters)
Discharge Chutes
► Three chutes: Oversize (upper), Accept (middle), Undersize (lower)
► Various standard configurations available (left, right, center, or full
width discharge)
99
DEBARKERSPRIM
ARY BREAKDOW
NSECONDARYBREAKDOW
NDRY KILNS
LUMBER
HANDLINGLUM
BERFINISHING
OPTIMIZATION
& CONTROLS
RESIDUALPROCESSING
USNR
Oscillation System
► Dual heavy steel counter-weights are held in place by maintenance
free (pre-packed with grease) double taper roller unit encased in a
steel housing (2” diameter throw)
► Electric motor drive (1800 RPM)
► Main shaft is CNC-machined from 7” or 8” diameter 1045 steel
Forano Chip Screen
Frame and Basket
► Welded structure made from high-strength 6”x 6” or 8”x 8” steel
tubing and 44W steel plate
► Basket balanced laterally and longitudally
► Basket hangs at a 7° angle from four hanger assemblies using
“heavy equipment” rated univeral joints
► Standard 2”x 2” square screen holes – other interchangeable round
and square screen sizes available, according to application
D A
E
F
G
C
B30"
FLOW
Discharge Chutes
► Two or three deck arrangement: Oversize (upper), Accept (middle),
Undersize (lower)
► Available with left, right, center, or full width discharge at each level
MODELS CS-25 CS-26 CS-28 CS-30 CS-32
A 2390 mm94”
3000 mm118”
3610 mm142”
4270 mm168”
4270 mm168”
B 1980 mm78”
2290 mm90”
2920 mm115”
3530 mm139”
4140 mm163”
C 1380 mm54-1/4”
1380 mm54-1/4”
1520 mm60”
1610 mm63-1/4”
1660 mm65-1/4”
D 990 mm39”
990 mm39”
980 mm38-3/4”
1030 mm40-1/2”
990 mm39”
E 460 mm18-1/4”
500 mm20”
420 mm16-1/2”
370 mm14-1/2”
370 mm14-1/2”
F 580 mm23”
580 mm23”
520 mm20-3/4”
430 mm17”
430 mm17”
G 1260 mm49-1/2”
1560 mm61-1/2”
2170 mm85-1/2”
2780 mm109-1/2”
2780 mm109-1/2”
H 1800 mm71”
2110 mm83”
2740 mm108”
3300 mm131”
3940 mm155”
Capacity(cords/hr)
6 10 22 28 34
Screen Surface 1520 x 1520 5’ x 5’
1830 x 1830 6’ x 6’
2440 x 2440 8’ x 8’
3050 x 3050 10’ x 10’
3050 x 3660 10’ x 12’
Required Power 2 HP 2 HP 5 HP 7-1/2 HP 7-1/2 HP
ApproximateWeight
1150 kg2500 lb
1400 kg3100 lb
2400 kg5250 lb
3800 kg8350 lb
4150 kg9100 lb
ShippingVolume
4 m3150 ft3
6 m3210 ft3
10 m3370 ft3
17 m3600 ft3
20 m3710 ft3
NOTE: Capacity based on regular/uniform feed. Chute positions modified according to requirements.
100
DEBA
RKER
SPR
IMAR
Y BR
EAKD
OWN
SECO
NDAR
YBR
EAKD
OWN
DRY
KILN
SLU
MBE
R HA
NDLI
NGLU
MBE
RFI
NISH
ING
OPTI
MIZ
ATIO
N&
CON
TROL
SRE
SIDU
ALPR
OCES
SING
USNR