Post on 05-Jan-2017
This sheet is designed to help you with the installation of a Parrot product and is purely for information. Any installation performed in compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation of Parrot SA. Pictures for information only.
SANDERO
SANDERO
Installation manual: Parrot MKi + Parrot CK3100 range
The brand name DACIA SANDERO and the DACIA logo are the property of DACIA. This document is only valid for the vehicle model SANDERO® year 2008 to 2011, excluding all other models in the same range and excluding later modifications made to the vehicle by the manufacturer. The Parrot brand name and logos are the exclusive property of Parrot SA.
This sheet is designed to help you with the installation of a Parrot product and is purely for information. Any installation performed in compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation of Parrot SA. Pictures for information only.
SANDERO
Accessories required
Disassembly 15min
Mounting kit 20min
Reassembly 15min
Testing 15min
Total 1h 05min
YES +IGN
YES ISO
N/A UNIKA
FRONT LOUDSPEAKER TEL mode
ALL MUSIC mode
Fitting time (estimated) / Main features
Tools
-Multimeter or Test lamp
- Wire tie
-Electrical tape
"Please contact your wholesaler to purchase accessories. A list of wholesalers is available at www.certified.parrot.com. "
To get the most out of your hands-free kit we recommend that you update your software regularly. The update procedure can be found at
www.parrot.com/usa/support/downloads
Updating
Plastic trim removal tools FACOM / BOJO
FACOM DX-25 kit (n°4 tools)
This sheet is designed to help you with the installation of a Parrot product and is purely for information. Any installation performed in compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation of Parrot SA. Pictures for information only.
SANDERO
Disassembly
This sheet is designed to help you with the installation of a Parrot product and is purely for information. Any installation performed in compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation of Parrot SA. Pictures for information only.
SANDERO
Disassembly
Insert the removal tools into the slots on each side of the radio.
Unclip the radio, pull it out and unplug the connectors and the
antenna. Then remove the radio.
Remove the passenger side door seal.
1
3
2
4
Using the plastic trim removal tools, unclip the car stereo and
air conditioning surround starting at the bottom and moving towards the top.
This sheet is designed to help you with the installation of a Parrot product and is purely for information. Any installation performed in compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation of Parrot SA. Pictures for information only.
SANDERO
Microphone passage
Glue the bracket (supplied) to the windscreen, after having
thoroughly degreased the surface.
Run the cable under the headliner to the passenger side support.
Run the cable along the passenger side windshield support while
replacing the door seal.
Then pass the cable under the dashboard on the bottom of the
glove box.
1
3
2
4
5
To finish, run it to the radio housing.
This sheet is designed to help you with the installation of a Parrot product and is purely for information. Any installation performed in compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation of Parrot SA. Pictures for information only.
SANDERO
Feeding the accessory cable
In the bottom of the glove box, insert the cable into the hole
next to the DIAG socket.
Then bring it out into the radio housing taking care to leave
enough length.
1 2
This sheet is designed to help you with the installation of a Parrot product and is purely for information. Any installation performed in compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation of Parrot SA. Pictures for information only.
SANDERO
ISO adapter
Fitting the hands-free system 1 / 2
On the kit connector (supplied), reverse the fuses (i.e. swap the red and orange wires) and
connect all the cables to the blue box as shown in the diagram below. Test everything before
reassembling...
1
...then store the box under the radio housing.
2
This sheet is designed to help you with the installation of a Parrot product and is purely for information. Any installation performed in compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation of Parrot SA. Pictures for information only.
SANDERO
Fitting the hands-free system 2 / 2
Glue the bracket (supplied) under the cover of the central console
between the air vents, after carefully degreasing the surface.
Pass the cable into the air conditioning housing while clipping
the console cover (TAKE CARE to avoid cutting the screen cable).
Re-clip the assembly and insert the screen.
3
5
4
!
This sheet is designed to help you with the installation of a Parrot product and is purely for information. Any installation performed in compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation of Parrot SA. Pictures for information only.
SANDERO
Testing
Before refitting the system, switch the kit on using the ignition (or by starting the car). By pushing the central knob of the remote control, check:
1 - that the menu is displayed on the screen (language or iPod etc) 2 - that the radio system is muted when the kit is in use (click in the blue box) 3 - that the sound through all speakers is properly muted 4 - that there is sound through the front speakers for spoken menus 5 - then turn off the ignition, verify that the kit turns off and that the message “goodbye” is displayed on the screen (otherwise reverse the fuses on the kit power supply harness) 6 - pair a telephone with the kit and make a call (check that both the microphone and the kit are working)
This sheet is designed to help you with the installation of a Parrot product and is purely for information. Any installation performed in compliance with the instructions appearing in this document is done under the sole responsibility of the installer, who is entirely responsible for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA RCS PARIS 394 149 496. May not be reproduced without the authorisation of Parrot SA. Pictures for information only.
SANDERO
Reassembly
Refit the system using the following procedure: 1 - reconnect the connectors and the antenna to the radio, slide it into its housing.