COMPANY PRESENTATION

ELECTRONICS FOR MATERIAL TESTERS

MODERNISATION AND SOFTWARE

STANDARD AND ULTIMATE

COMPRESSION FLEXOMETER

MEASUREMENT TECHNOLOGY

WWW.DOLI.DE

WWW.FLEXOMETER.COM

2 firmen_praes_long_en.doc

State 140606

Introduction Corporate Name: DOLI Elektronik GmbH

Headquarters: Adi-Maislinger-Straße 7, 81373 München, Germany +49 89-20 243-0 Fax +49 89-20 243-243 e-mail info@doli.de

Production: Ulmer Straße 34, 89584 Ehingen, Germany +49 7391-58039-0 Fax +49 7391-58039-71 e-mail ehi@doli.de

Sales: Mühlstr. 26, 55271 Stadecken-Elsheim, Germany +49 6130-944 250 Fax +49 6130-944 251 e-mail sales@doli.de

Internet: www.doli.de

www.flexometer.com

firmen_praes_long_en.doc 3

History and Structure

More than 20 companies with more than 150 employees evolved from the company

"Gruppe Ingenieurbau München", founded in 1976 in the city of München in Germany. DOLI

Elektronik GmbH is one of those companies, the founders of which have their roots in the

weighing technology, processor system development and general measuring and control

engineering. Nowadays, DOLI has six partners, two of them managing. In 2013, DOLI obtained

a turnover of more than 5 Mio. EURO in three locations and with 35 employees.

Managing Partners:

Ernst Ams, Michael Grupp

Further Partners:

Klaus Böck, Rolf Grupp, Hermann Schabel, Harald Schmid

Employees 35

Turnover 2013 more than 5 Mio. EURO

Registered Capital 150,000 EURO

HRB München 52456

Know-How

Detection of physical outputs, such as: load, position, strain, time, angle, temperature, acceleration.

Amplifier and AD-conversion: standard ±180.000 digits in real-time.

Incremental detection systems: Sinusoidal signal desampling, high counting frequencies.

Digital control of electrical and hydraulic drives, especially for static and dynamic testing.

Safety technologies, such as: Limit switch, limit values, transmission protocol, emergency stop, shielding.

Real-time systems: multitasking, synchronization.

Using contemporary technologies (SMD, PLD), powerful electronic components are constructed in a compact design.

Development and production of exchangeable componentry (exchange without post-adjusting).

4 firmen_praes_long_en.doc

Electronics for Material Testers

EDC220√, EDC222√ and EDC580√ – new External Digital Controllers

Digital control; Closed Loop Control

'Bumpless Transfer'

Detection of load, position, strain etc.

Display of outputs (stand-alone)

Data acquisition (stand-alone)

Test control (stand-alone)

Test analysis (stand-alone)

Data-logging (stand-alone)

Interface to PC, printer

Fits perfectly for dynamic testers!

RMC1, RMC6, RMC7 – Remote Machine Controls for comfortable use

RMC1 and RMC7 – same properties as the EDC front panel

RMC6 – compact RMC for the control of the X-head

Hub for the connection of several RMCs

Digital Amplifiers – either inside the EDC or with extra case

VAI32, VAI35 – Servo valve amplifier with up to 300mA for assembly inside the EDC

DC012, DC160 and DC320 – internal power amplifiers for motors with up to 320 Watt

DC1100 and DC2500 – external power amplifiers for DC servo motors with up to 2500 Watt

Power amplifier CE and PELV conformal

AC-motors and power amplifiers adapted to the applications

firmen_praes_long_en.doc 5

Electronics for Material Testers:

New electronics for Screw Testers.

Existing material testers with electrical drive will be equipped with a new controller. If necessary, the motor will be changed, too. With this RetroFit, you will have a state of the art testing system with closed loop control. Additional appliances (e.g. Extensometer) will be adapted or DOLI delivers new ones.

DOLI retrofits all kinds of testing systems - independent from the producer.

Modernisation of Hydraulic Testers.

Hydraulic testing systems will be modernised according to the task and existing equipment. Even manually controlled instruments with plunger of an older style will be equipped with new hydraulics and a servo valve. Hence, an automatic test run will be guaranteed even with these kinds of instruments.

DOLI has been retrofitting testing instruments since 1979. And from 1986 on, DOLI retrofits with closed loop control.

Modernisation of Dynamic Testing Systems.

With the EDC580, DOLI retrofits dynamic testing systems, also. With the RetroFit, even testing with frequencies of up to 500Hz can be realized! DMA- and energy calculations will be possible as well as an analysis of the elastic stiffness. Whether static or dynamic – it does not matter to us:

DOLI offers the complete solution for your tester!

It contains control electronics and software, the exchange of motors or hydraulic power packs, as well as the repair of cylinders or the adaptation or exchange of transducers or additional accessories.

6 firmen_praes_long_en.doc

Linear Motors.

For the „low-load“-range, DOLI offers Linear

Motors as cost effective alternatives to the more expensive hydraulic or compressed-air systems.

These linear motors are available as AC- or DC-linear motors for different applications and they can be used together with the EDC and the

Test&Motion Software.

Test&Motion Software for Material Testing Applications.

Evaluation software for almost all kinds of applications

Data detection, with PC

Test control, with PC

Test analysis, with PC

Data-logging, with PC

Control of dynamic and static instruments

Test&Motion DynPack – the Software for Dynamic Applications

Display and procession of up to 10 channels simultaneously

Data transfer with 5kHz

Control of multiaxial systems

Oscilloscope function for dynamic applications

Display of covering curve

Limit assignment in a absolute and relative manner

Function generator for ramps, triangle and sinusoidal functions

Sweep between frequencies and amplitudes

Superimposition of different curve forms

firmen_praes_long_en.doc 7

Measuring Technology

PC-Incremental Boards

PC-incremental boards for the direct acquisition of four rectangle or sinusoidal incremental transducer signals. The PCINC4-board is based on a state-of-the-art board with eight additional digital I/Os. She replaces the PCINC3-board. These boards have been designed especially for OEM customers in the field of measuring instruments. PC104-board for the direct connection of two incremental transducers

8 firmen_praes_long_en.doc

The DOLI Compression Flexometer Family:

Standard (“Goodrich”) or Ultimate, manual or fully automated!

The Standard DOLI Compression Flexometer, known as “Goodrich Flexometer” also, still has the classic eccentric drive. But the Ultimate Flexometer is driven by an energy saving and environment friendly linear motor!

Both instruments are available as manual or fully automated version. The fully automated version, including a handling system for the rubber samples, supplies results without staff influence. Unpopular handling and adjusting is eliminated. Temperature measurements are done with the puncture needle immediately. Therefore, measurement errors by temperature loss are almost eliminated.

With the newly developed WindowsTM

Software DOLIFlex and its functions “Multichart” and “Calibration”, the DOLI Flexometer is completed to a versatile and easy-to-use testing system!

firmen_praes_long_en.doc 9

München : Headquarters, Management and R&D

The DOLI centre for hard- and soft-ware development can be found in München. This is the point, where all products get created and prepared up to serial production. Special tasks, such as testing systems or special electronics for customers are generated exclusively at this de-partment. 16 employees, mostly engineers for hard- and software development create solutions for the most effective combinations of new and existing technologies and the best price.

Using powerful software tools makes soft- and hardware developments much more

efficient.

Programming digital hardware in PLDs increases the functionality and efficiency, at the same time this means a safe of time and costs.

Separate Boot- and BIOS- programs enable the application of a standard interface from the software to the hardware as well as upward compatibility.

The DOLI Multitasking-Kernel and the Interrupt-Processing are the best conditions for real-time application.

Software Updates for the Micro-Controller-Hardware is done by a simple download into a Flash-EPROM. This is a big advantage in case of service needs.

Continuous testing of new technologies and componentry in purpose of finding possible improvements for DOLI products and customer products

10 firmen_praes_long_en.doc

Ehingen/Donau : Production In our department in Ehingen, we use a computer controlled production planning system to control the material management and the production.

The raw material stock contains more than 5,000 different electronic and mechanic components.

The components will get distributed and placed for the different production orders.

Following TQM-directions, we calibrate and check the processed componentries at modern measuring desks.

Single componentries are produced in advance, whereas complete appliances are produced in an order-related manner. This guarantees a fast reaction time on orders and a variable and flexible production process. The finished appliances and compo-nentries will be subject to an automatical final test.

firmen_praes_long_en.doc 11

Stadecken-Elsheim (Frankfurt Area) : Sales/Service

With its location in the Rhein-Main-Area, the sales department in Stadecken-Elsheim close to Frankfurt is much more centralised than the headquarters in München. This enables DOLI to serve its customers in a very fast and cost effec-tive manner. Furthermore, the vicinity to the airport in Frankfurt offers the possibility to serve even international customers in a fast and flexible way.

The main tasks are the following:

Introduction of new products by brochures, commercial etc.

Marketing for existing and new products

Complete design and project work for exhibitions

Customer offers including offer creation and all following tasks

Customer service with pre- and after sales service

Service point for DOLI Systems

Ret_short_en.doc

RetroFits for Testing Instruments

Is your Testing System a digital one already?

We offer NEW DIGITAL control electronics for YOUR testing application !

Combine the quality of your testing instrument with the comfort of a digital control by DOLI !

Hydraulic Testing Instruments

DOLI RetroFits all testing systems with single- and double-acting actuators.

The EDC offers new possibilities in data acquisition as simple acquisition only (control remains manual) or as a complete digital control system. Servo valves can be incorporated or retro-fitted, as necessary. Special configurations (e.g. connection of strain gauges at the front, as shown) can be custom built as required. During RetroFit all the electric, electronic and hydraulic systems are checked and modified to conform to the latest standards.

Screw Driven Instruments

Based on our experience with RetroFits we are able to provide a solution to update almost all kinds of screw driven testing instruments. The DOLI EDC offers improved reso-lutions of load, position and strain. The new digital control permits advanced control of all systems and significantly enhances the machine capability. Power outputs and drives are changed or adapted as needed.

Test&Motion software

offers a wide range of standard test modules. Special modules as the Free Programming

or the Flexible Flow Control

offer complete freedom in compiling custom test methods to the user – without the need of any programming knowledge.

Independent of the producer

All transducers connectable

Automations can be modernised, also

RetroFits for special testing systems

Individual adaptations

RetroFits for self-made systems

RetroFits for special hydraulic instruments

ASCII Interface to LabView,

Visual Basic etc. via DoPE

Test&Motion software for almost all tasks

Ret_short_en.doc

Test&Motion

Test&Motion – The Data Evaluation on the PC

The Graphic

During the test, the test results will be shown online as curve. It is possible to individually process the results after the test is done.

Display of several curves, even with displacement

Zoom function

Marking of points

Text insertion into the graphic

Two values at one axis

Dynamic: oscillograph, covering curve, data reduction, peak control

aso.

Visit our web page: www.doli.de

„A test software should evaluate everything I need display everything I want to

give everything out the way I like it!“

DOLI combined these tasks in the Test&Motion – Basic Software, showing dif-

ferent information in different windows at the same time. Our new testing program Test&Motion has been developed in a modular design. It consists of the basic

software containing a simple but adaptable tension/compression test and different modules for almost all kinds of testing applications. The special module “Free Programming” offers the possibility to design tests in an individual manner.

All sorts of signal sources can be displayed. Load, position and strain are standard, but other transducers or calculated results can be displayed. Sample diameter, temperature, scales etc. are possible as well as occurences via I/Os.

T&M Basis - The basic software with a simple tension/compression test!

Application Modules - The perfect Module for each Application!

Free Programming Module - Absolutely individual design of test methods!

T&M DYNPACK - the software for dynamic tests incl. easy block programming

DOLI Elektronik GmbH

Adi-Maislinger-Straße 7 81373 München/Germany Phone: (+49)-0-89-20 243-0 Fax: (+49)-0-89-20 243-243 e-mail: sales@doli.de Internet: www.doli.de

Advantages

Simple and intuitive

“Free Programming” for individual tests

Almost all kinds of standard evaluations directly available

Special applications made-to-measure to your needs

Fits for special testing systems, concrete testers etc.

Data

Digital display of all channels

Channels editable

Display of the test curve even after the test

Results can be chosen and displayed one by one

Result export as ASCII- or Excel file

Connection to LIMS

Data transfer from additional appliances, such as thickness gauges, scales etc.

Connection even of IEEE appliances

Dynamik_short_EN.doc

Dynamic Testing

Dynamic tests with up to 500Hz – with DOLI Dynamic Controllers

Whether static or dynamic – DOLI is your partner!

Dynamic material and component testing for small loads under 5kN are being realized more and more with up to date electrical drives. The smaller the load becomes, the bigger the advantages are compared with the typical hydraulic actuators. These are:

High energy efficiency

Simple construction type

Low costs for purchasing and maintenance

High mobility

A hydraulic drive on the contrary transforms the entire electrical energy into oil temperature when working with small loads and acquires maintenance at regular intervals.

With multiaxial systems, hydraulic and electrical linear axes can even be simply combined – an ideal, cost reducing arrangement, which is used in many cases already.

DOLI Elektronik not only offers you well engineered controllers and power amplifiers, but also all drives mentioned here as well as a complete system integration to test stands.

At the same time our testing software Test&Motion Dynpack will assist you with all testing tasks, e.g. component testing, series testing, crack growth measurement, a.s.o.

Electro mechanical

screw drives

Electro linear

actuators

Voice-Coils

Hydraulic

actuators

High dynamic drive solutions for small loads

Dynamik_short_EN.doc

Dynamic Testing

The proper drive – with DOLI Dynamic Controllers

DOLI is developing controllers for material testing instruments for more than 20 years. The program for drive systems covers DC-drives, AC-drives, hydraulic components and nowadays linear drives, also. All systems are synchronized to the EDC-controllers and ready for use immediately.

DOLI provides you with: completely tested units with motor, power amplifier, controller and software.

Fig: Ideal application of drive technologies for dynamic testing

Electro mechanical screw drives often replace pneumatic actuators in test stands due to their excellent controllability. DOLI-screw drives are designed for transversal loads from up to 20% of the nominal load. Common performance data is 100 to 200mm stroke, nominal load from 800N to 50kN and speeds from 100 mm/min to 12,000 mm/min.

Electro linear actuators are linear motors, which completely run without rotating parts. Due to their unbeatable high dynamics they are likely used for dynamic testing in the lower range of performance. DOLI presently offers linear drives with nominal loads from 500N and 2kN. The normal stroke from 100mm is sufficient for common dynamic tests. Designed e.g. with 5mm amplitude at 20Hz.

Voice-Coils (loud speaker principle) replace hydraulic pulsers and are characterized by a maximum dynamics and a most simple construction type. Hence, they are not subject to any mechanical wearout. Voice-Coils especially fit for working life tests of very small samples and for compounds in the range of medical engineering, such as e.g. implants or hip joints. DOLI offers Voice-Coils with 100N and 10mm stroke and 210N and 30mm stroke. Designed e.g. with 1.8mm amplitude at 50Hz.

Hydraulic actuators. Plungers are well spread in the filed of material testing fro decades. Hundreds of such testers run with EDC controllers by DOLI, some of them with new hydraulic powerpacks and servo valves. Differential cylinders and synchronized cylinders with servo valves are used for static and dynamic applications. With the controller EDC580V, DOLI again did a huge step towards dynamic. The EDC580V replaces the controllers from the last decades. DOLIs hydraulic „Know How“ brings entire testing systems back to state-of-the-art. On demand, DOLI supplies: controllers, servo valves, actuators, hydraulic powerpacks, manifolds a.s.o. Visit our webpage www.doli.de

Advantages

Individually designed actuator systems

Tested All-in-one systems – from drive to software

Technical service for material- and component testing

Comprehensive Know-How-Transfer for dynamic drive systems

Identical operation of different systems

Huge Know-How in the field of static and dynamic testing

Excellent accessibility

Short reaction times

Software

Test&Motion Dynpack for

dynamic applications

Multiaxial tests

Biaxial tests

Same user surface for all applications

DOLI Elektronik GmbH

Adi-Maislinger-Straße 7 81373 München/Germany Tel: (+49)-0-89-20 243-0 Fax: (+49)-0-89-20 243-243 E-Mail: sales@doli.de Internet: www.doli.de

Hydraulic actuators

Voice-Coil

Electro linear actuators

Electro mech. screw drive

Test frequency [Hz]

Test

load

[kN

]

4ETF_4FAD_short_en.doc

Electronics for Testers

Carrier Frequency Measurement Amplifiers

for strain gauges, LVDTs and DC-Signals

4ETF and 4FAD – I4-Interface plug-in cards for the EDC

Combine the quality of your testing instrument with the comfort of a digital control by DOLI !

EDC – the control electronics as modular system

DOLIs External Digital Controller is

a measurement and control system, developed especially for testing systems. Almost all kinds of analog or incremental transducers can be connected via plug-in cards. It is possible to process 16 channels. In order to serve all kinds of testing systems, the EDC family offers several versions and connection possibilities for all kinds of drives. Of course, as digital controller, the EDC offers a bumpless transfer between load-, position- and strain control.

4ETF – the card for static applications

The plug-in card 4ETF is a ‚carrier frequency measurement amplifier’ with A/D-converter for strain gauges, LVDTs and DC-Signals. It suits especially for load-, position-

and strain transducers, but is used for temperature and other physical quantities, also. The A/D-converter of the card is an integrating voltage/frequency-con-verter. The A/D-conversion happens with a resolution of

180,000 steps and an integration time of 20ms.

4FAD – the card for dynamic applications

The plug-in card 4FAD is a ‚carrier frequency measurement amplifier’ for strain gauges, LVDTs and DC-Signals. It fits especially for static and dynamic applications with a testing frequency of up to approx. 100Hz. Similar to the 4ETF card, the A/D-conversion of the 4FAD happens

with a resolution of 180,000 steps and an integration time of 20ms.

Available as plug-in card for the EDC from DOLI

Sensor coding stored in the EEPROM of the sensor plug

Automatical read-in of sensor- and calibration data with switch-on or on demand.

Recognition of all kinds of transducers with sensor plugs

Automatic adaptation to the new sensor at sensor change

A/D-conversion 180,000 steps

Carrier frequency 5kHz

Linearity 0.01%

Accuracy 0.025%

static

dynamic

Electronics for Testers

Order Nos and Accessories

I4-Interface cards

0725 4ETF 5kHz supply

A/D 180.000 steps

1520 4FAD 5kHz supply

A/D 180.000 steps, 5.000Hz data logging

Analog output

1835 ANA2 Analog output 10V for 4ETF, 4FAD, 2DCA, 2CFA, EDC220, EDC222

Sensor plugs

for strain gauges and LVDTs

Sensor plug with reference divisors for transducers with a sensitivity of:

0745 SGS 1mV/V

0580 SGS 2mV/V

0746 SGS 4mV/V

0747 SGS 8mV/V

0748 SGS 16mV/V

0749 SGS 32mV/V

0750 SGS 80mV/V

0751 SGS 160mV/V

0752 SGS 320mV/V

0753 SGS 640mV/V

for DC-Signals

Sensor plugs with reference divisors for:

1057 SGS 1VDC

1135 SGS 2VDC

0754 SGS 5VDC

0755 SGS 10VDC

Technical Comparison 4ETF – 4FAD

Visit our homepage www.doli.de

4ETF 4FAD

Amplification and Supply

Carrier frequency 5kHz Sine

Supply voltage (in Veff) 1.1 – 2.5 – 5.5V

Sensitivity of the transducer 1.16 – 1,625mV/V

Internal resistance of the transducer 85

Source resistance of the signal source (CF-operation mode)

1,1k

Source resistance of the external reference (CF-operation mode)

1,1k

DC voltage input 0.727 – 1.625V

Input resistance (DC voltage measurement)

15 M

Common mode range 6,5V

Common mode rejection 80dB 95dB 105dB

Filter: Besselfilter 3rd degree 100Hz 1.000Hz

Converter

Type U/f- Converter

‚Successive Approximation’

with ‚Over Sampling’

Resolution at 20 ms integration time and 100% signal

180.000 steps 180.000 steps

at 250ms integration time 1.770.000

steps 1.770.000 steps

Linearity of amplifier and converter for

up to 150% of the nominal range Typical 0.01% (0.025%max)

Temperature influence per °Kelvin Offset 0.001%/°K

Amplification 0.01%/°K

DOLI Elektronik GmbH

Adi-Maislinger-Straße 7 87313 München/Germany Tel: (+49)-0-89-20 243-0 Fax: (+49)-0-89-20 243-243 e-mail: sales@doli.de Internet: http://www.doli.de

Sensor plug

Data of the connected transducer are stored in the EEPROM of the sensor plug. These data (physical units, nominal value, reference value, max. supply voltage, amplification etc.) will be read-in and processed either with switch-on or on demand. Display noise for static applications

The value of a connected sensor is allowed to vary with max. 0.002% of the nominal value (that equals 2 digits at 100,000 digits). Conditions:

1. Tester non-operative, integration time 100ms, load cell unloaded. 2. Tester runs, integration time 100ms, load cell not inside the tester, but

connected electrically.

Data transmission 4FAD

Valid for continuous changes and 100% signal, Ethernet interface

Channels Signal Max. transmission rate per channel

16 Sine 5,000Hz

Kanäle

3

4

7

8

Hydraulik Zuschaltblock_short_ge-en

Hydraulik - Hydraulics

Hydraulischer Zuschaltblock

Hydraulic Substation (service manifold)

Damit kann Ihre Hydraulik mehr!

Upgrades your hydraulics!

Was macht der Zuschaltblock? Der neue hydraulische Zuschaltblock von DOLI erlaubt die kontrollierte Zuschaltung von Verbrauchern in Hydrauliksystemen.

Wozu brauche ich das? Druck und Volumenstrom des neuen Verbrauchers werden langsam dem Druck des Hydrauliksystems angepasst. Dadurch wird die Beeinflussung von laufenden Versuchen an anderen Verbrauchern durch Druckabfall wirkungsvoll ausgeschlossen.

Woraus besteht das System? Die Basisplatte mit den Hydraulik-systemanschlüssen, die Abschluss- platte sowie ein Zuschaltblock bilden die Grundeinheit des Systems. Zwischen Basisplatte und Abschlussplatte können bis zu vier Zuschaltblöcke montiert werden.

Wie funktioniert das? Jeder Zuschaltblock steuert die Druckleitung für einen Verbraucher. Er regelt den Druck langsam von Nieder-druck auf Hochdruck und das Ventil schaltet dann den maximalen Fluss frei. Diesen Zustand meldet der Zuschalt-block dem System über einen Druck-schalter. So kann auch ein Schlauch-platzer erkannt werden.

What is the aim of the substation? The new hydraulic substation by DOLI connects one or more hydraulic testers to a hydraulics supply in a controlled manner.

Why do I need this? Pressure and flow of the tester will smoothly be adapted to the constant hydraulics supply, thus preventing other connected testers from being disturbed by pressure drops very efficiently.

What does the system consist of? The base plate bearing the connec-tions to the main hydraulic system, a closing plate and one substation represent the basic unit of the system. Up to four substations in total can be mounted in between the base plate and the closing plate.

How does this work? Each substation controls the pressure connection of one tester. The substation slowly rises the pressure from low pressure to high pressure and then, the valve releases the maximum flow. The substation signals this state to the system via a pressure switch. This way, even a bursted hose can be detected.

Kompatibel zum Schenck Anschlussventil

Komfortabler Anschluss von Prüfmaschinen an ein Hydrauliksystem

Kontrollierte Zuschaltung neuer Verbraucher

Keine Beeinflussung laufender Versuche

individuelle Änderungen leicht möglich

bis zu vier Verbraucher möglich

Compatible with Schenck ‚Anschlussventil‘

Comfortable connection of testers to a hydraulics supply

Controlled connection of a new appliance

No influence to running testers

Individual changes possible

Up to four appliances possible

DOLI Hydraulik für Prüfmaschinen – DOLI hydraulics for testers

Hydraulik Zuschaltblock_short_ge-en

Hydraulik - Hydraulics

Ein System – viele Möglichkeiten – One system – High potential!

Besuchen Sie uns im Internet - visit our website - www.doli.de

Leistungsfähig:

Sie können bis zu vier Verbraucher in einem Hydrauliksystem zusammenführen – jeder ist einzeln ansteuerbar.

Kompatibel:

Natürlich sind die DOLI Zuschaltblöcke kompatibel zu den verbreiteten Zuschaltblöcken (Anschlussventilen) der Carl Schenck AG. Sie können also einfach und problemlos Ihre Schenck Anschlussventile mit DOLI Zuschaltblöcken erweitern und umgekehrt.

Technische Daten:

Niederdruck: 1-40l/min,35-280bar

Hochdruck: 250l/min, max.350bar

Betriebsspannung: 24VDC

Stromaufnahme max. 2,5A

Gewicht Abschlussplatte: 10kg

Gewicht Zuschaltblock: 28kg

Gewicht Basisplatte: 32kg

Abmessungen Basismodul mit einem Zuschaltblock Breite x Höhe x Tiefe in mm: 355 x 353 x 359

Dicke je Zuschaltblock: 85mm

Befestigung: 140x200mm, Ø10mm

DOLI Programm für statische und dynamische Prüfsysteme

Modernisierung von Prüfsystemen

EDC580V – DOLI Dynamic Controller

Hydraulische Zylinder und Aggregate für viele Anwendungen

Test&Motion Dynpack - dynamische Software

Lineare Antriebe für dynamische Prüfungen

Realisieriung von Sondersystemen

DOLI program for static and dynamic tests

RetroFit of testing systems

EDC580V – DOLI Dynamic Controller

Hydraulic actuators and powerpacks for a lot of applications

Test&Motion Dynpack –dynamic Software

Linear drives for dynamic applications

Construction of special systems

DOLI Elektronik GmbH Adi-Maislinger-Straße 7 81373 München/Germany Tel: (+49)-0-89-20 243-0 Fax: (+49)-0-89-20 243-243 E-Mail: sales@doli.de Internet: www.doli.de

Powerful:

You can connect up to four appliances to a hydraulic system – and control each of them separately.

Compatible:

Of course, DOLI-Substations are compatible with the substations (‘Anschlussventil’) of the Carl Schenck AG. Thus, you can easily expand your Schenck based modules with DOLI-substations and vice versa.

Technical Data:

Low pressure: 1-40l/min,35-280bar

High pressure: 250l/min, max. 350bar

Operating voltage: 24VDC

Current consumption: max. 2.5A

Weight closing plate: 10kg

Weight substation: 28kg

Weight base plate: 32kg

Dimensions of base module equipped with one substation width x height x depth in mm:

355 x 353 x 359

Extra width for additional substation: 85mm

Fixation: 140x200mm, Ø10mm

a) a) b) b) b) b) b)

c) c)

Abb. 1: Grundeinheit, bestehend aus: a= Abschlussplatte, b=Zuschaltblock, c=Basisplatte. (2891)

Pic. 1: Basic unit, consisting of a = closing plate, b = substation, c = base plate (2891)

Abb. 2: Maximale Einheit mit vier Zuschaltblöcken (a= Abschlussplatte, b=Zuschaltblock, c=Basisplatte) (2891+2892+2893+2894)

Pic. 2: Maximum unit with four substations (a = closing plate, b = four substations, c = base plate) (2891+2892+2893+2894)

2891 2891

2891 2891 2891 2891 2892 2893 2894

TaM_short_en.doc;

Test&Motion

The intelligent Solution for your Test Applications

Test&Motion

Combine the Quality of your Testing Instrument with the Digital Control and Software by DOLI !

„A test software should be able to 1. display everything I want to 2. evaluate everything I need 3. give everything out the way

I like it!“

DOLI combined these tasks in the Test&Motion Software. The Software shows different information in different windows at the same time. All sorts of signal sources can be displayed. Load, position and strain are standard, but other transducers or calculated results can be displayed, also. Sample diameter, temperature, scales, etc. are possible as well as results via I/Os. Variables are shown as curves in X- or Y-direction or are listed digi-tally. The variable names can be changed (e.g. load or F), the graphic can be zoomed several times and remarks can be stored within the graphics. If a larger view of the curves is needed, the graphics window can be drawn up to screen size. Due to the organisation in single windows, you have the possibility to move important values to a point where

you can still see them. Test&Motion - as a Windows™ program - serves all Windows printers. However, in order to distinguish the test curves, we recommend to use a color printer. All results and statistic values as well as all settings and data regarding the tests, can be given out selectively. You can print your company logo, header or foot line – just as you wish! Test&Motion consists of the basic software T&M_Basis and different application modules. All application modules use the basic software as platform. Then, they offer special types of calculation, the results of which can be displayed and printed. Adding the modules Free Programming and Flexible Flow Control, everything is possible! The EDC from DOLI can detect and transfer data with 5,000Hz, and the Test&Motion software is just as fast. For dynamic testers, we have the T&M Dynpack software. EDC580V and Dynpack control dynamic systems with 500Hz.

Simple and intuitive operation

Customised and field-proven applications

All protocols and printouts freely definable

“Free Programming Module” for individual tests

Compatible to each EDC system from DOLI

Export into ASCII or EXCEL files

Almost all applications possible in the testing lab

Use as production testing system in online mode, also

Integrated graphics

Integration of several additional channels possible

Direct connection of thickness gauges, callipers and other measurement instruments via RS232

Fast and reasonable testing

Test&Motion

T&M – Program Structure

Visit our web page www.doli.de

Our testing software Test&Motion has been developed in a modular design. It consists of the basic software T&M_Basis containing a simple but adaptable tension/ com-

pression test and different modules for almost all kinds of testing applications. The special module Free Programming offers the possibility to design tests individually.

Advantages

Simple and intuitive

Free Programming for individual tests

Almost all kinds of standard evaluations directly available

Special applications made-to-measure to your needs

Fits for special testing systems, concrete testers etc.

Data

Digital display of all channels

Channels editable

Display of the test curve even after the test

Results can be chosen and displayed one by one

Result export as ASCII- or Excel file

Connection to LIMS

Data transfer from additional appliances, such as thickness gauges, scales etc.

Connection even of IEEE appliances

DOLI Elektronik GmbH

Adi-Maislinger-Straße 7 81373 München/Germany Tel: (+49)-0-89-20 243-0 Fax: (+49)-0-89-20 243-243 e-mail: sales@doli.de Internet: www.doli.de

The Graphics

T&M Basis

The basic software with a simple tension/compression test!

User surface for all T&M modules

The test can be adapted to almost all kinds of applications

User surface; parameter input and storage; graphic X/Y-display on-line

Possible X- and Y-axis quantities: load, stress, X-head travel, strain, technical strain, time (from test start), true strain, nominal strain, time and defined signal input

Determination of five values on the X- or Y-axis, maximum, breach as X- and Y-value. Corresponding determination of values for compression tests.

Adaptation to LIMSystems

Statistic functions: mean value, min/max value, range, median, standard deviation, practical limit of error, etc.

Display of all data sent by the instrument: load, X-head travel, strain and defined signal input

The Application Modules

The perfect module for each application!

Metal tensile/compression and bending tests according to DIN and EN

Continuing tearing-, separation-, peeling test

3-point-/4-point-bending test (EN 63)

Plastics test acc. to DIN, ASTM D etc.

Textile tensile test according to DIN

Cyclic ring stiffness- and pipe pressure tests according to ISO 9969

Torsion test (Tension/Torsion)

Adaptable tests: seam shifting resistance, spring test, cyclic load, 3 integral, ball indentation hardness, compression stress, calibration of load transducers etc..

Free Programming and Flexible Flow Control

Absolutely individual design of test courses – created by the user himself.

This application module offers the possibility to combine any number of blocks in the test course. It is possible to define individual speeds and test end criteria (e.g. predefined stress or strain) for each block.

During the test, the test results will be show online as curve. It is possible to individually process the results after the test is done.

Display of several curves, even with displacement

Zoom function

Marking of points

Text insertion into the graphics

Two values in one axis

etc.

DC1100_2500_short_en.doc

DOLI Power Amplifiers

Power amplifiers with 12W, 160W, 320W, 1,100W and 2,500W either EDC-internal or as external desk top unit!

Combine the quality of your testing instrument with the comfort of a digital control by DOLI !

Electronics for testers

DOLI offers electronics and very powerful software for data acqui-sition and closed loop control for testing instruments like tensile testers.

The software runs on the DOLI hardware platforms as EDC220V, EDC222V and EDC580V and others. It is configurable within a wide range to satisfy all tasks of a testing instrument.

The communication between DOLIs EDC-system and the PC happens via USB or Ethernet. DOLI uses a safe protocol called DPX on this serial line to transmit commands and data in both directions.

DOLI Power Amplifiers

DOLI offers different amplifiers for DC-motors and servo valves. AC-motors and other drives are controlled by a ±10V output.

DOLIs internal digital power amplifiers can be implemented into the desk top units EDC222V and EDC580V. They are available for DC-motors with 12W, 160W and 320W.

The power amplifiers DC1100 and DC2500 are external designs for DC-motors with 1.100W respectively 2.500W. They are available for all three external digital controllers, i.e. for the built-in unit EDC220V, as well as for the desk top units EDC222V and EDC580V.

High control accuracy: ±1 increment of the transducer

No drift and therefore no brake needed

No tacho needed

Extremely high dynamics of the drive

Direct connection to the EDC-systems

Safety low voltage PELV from IEC 204-1 guaranteed

CE conformal

Cost effective

Digital Power Amplifiers . . . . . . always the fitting amplifier for your instrument drive!

DC1100_2500_short_en.doc

DOLI Power Amplifiers

Visit our web page www.doli.de

The external power amplifiers DC1100 and DC2500

External DOLI power amplifiers are available for DC-motors with 1.100W (DC1100) and with 2.500W (DC2500). They offer a digital interface to the EDC. A negative feeder possibility of 50W (DC1100) or 200W (DC2500) enables cyclic tests, e.g. spring tests. The power amplifiers contain the complete contactor and relay technics needed for a safe turn-off in case of emergency stop, softends etc. A function check of the safety relevant elements is guaranteed in connection with the controller componentries. The DC1100 and the DC2500 power amplifiers do not need a tacho-generator at the DC-motor, as they are controlled by an incremental trans-ducer on the motor shaft.

DOLI Elektronik GmbH

Adi-Maislinger-Straße 7 87313 München/Germany Phone: (+49)-0-89-20 243-0 Fax: (+49)-0-89-20 243-243 e-mail: sales@doli.de Internet: www.doli.de

External DC power amplifiers

DC1100 – 1.100W for EDC222/580V

DC2500 – 2.500W for EDC222/580V

Digital Interface with EDC220//222/580V

Inrush current limitation

Closed loop current controller

Brake resistant at output

During deceleration, the reverse motor energy is switched back into the intermediate circuit.

The controller electronics guarantees the safety low voltage PELV according to EN60204 (V< 60V)

The power amplifier supply is disconnected at fault (emergency stop, limit-switches etc.) via a conductor or relay

Further DOLI power amplifiers

Internal DC power amplifiers DC012 – 12W for EDC222/580V DC160 – 160W for EDC222/580V DC320 – 320W for EDC222/580V

Internal servo valve amplifiers VAI32 – 300mA for EDC220 VAI35 – 300mA for EDC222/580V

DC1100 or DC2500

External Digital Power Amplifiers With 1.100W or 2.500W

Comparison

Model DC1100 DC2500

Nominal output power 1100Watt 2500Watt

Rated current 1.25-11A 2-16.5A

Maximum current 2 * Rated current maximum 14A

2 * Rated current maximum 20A

Voltage 15-105V 22-150V

PWM 20kHz 20kHz

Peak reverse power Continuous reverse power

1,200W for 0.5s 50W

1,200W for 2.4s 200W

Power supply 115 / 230V AC 230V AC

Supply for motor brake 24V/1A 24V/1A

Dimensions [mm] 276 x 118 x 300 276 x 175 x 445

Weight 12kg 28kg

Enclosure protection IP31 IP31

EDC220V/222V/580V

Full stand alone systems for all types of material testing instruments. Excitation and A/D-conversion of transducers as well as complete digital control of the connected drive are included.

Load resolutions and options: EDC220V/222V: ±180,000 Steps (two option slots) EDC580V: ±180,000 Steps with 4ETF or 4FAD (seven option slots)

DOLI produces electronics for testing instruments since 1979. The first digital contoller was presented in 1984. 95% of the production is delivered to producers of instruments worldwide.

DOLI supplies electronics, motors, amplifiers, application software and has enough know-how to support producers in the field of new testing equipment and retrofits.

dope_short_en.doc

DoPE

Control, data acquisition, I/Os . . .

. . . with one DLL . . .

DoPE ! !

DOLI has electronics and very powerful software for data acqui-sition and closed loop control for testing instruments like tensile testers. This software runs on the DOLI hardware platforms as EDC220V, EDC222V and EDC580V and others. It is configurable within a wide range to satisfy all tasks of a testing instrument. The fast communica-tion with the PC happens via USB or Ethernet. DOLI uses a safety protocol called DPX on this serial line to transmit commands and data in both directions. This totally flexible communication is thinking in transducer points. One point represents one step of an incremental transducer or one step of the total load resolution. Therefore, communication does not depend on the type of instru-ment. Using DoPE from DOLI, a DLL under Windows, the programmer uses SI-units, making the connec-tion to existing application programs much easier, while all the flexibility will be kept. It turned out that positioning commands in the customer application software will work after a few hours.

DoPE is your communicator !

Your application software

connects easily to the

EDC Systems

Full control of testing

instruments in closed

loop control (position,

load or strain)

For Windows™

operating systems

Very fast communication

via USB or Ethernet

Sample Programs for:

C™ ; Visual BASIC™ ;

DELPHI™ ; LabVIEW™

Control cycles and data

transfer rate up to

5,000Hz

DoPE Test Center: Our

service software enables

you to see all conditions

of the instrument

One communication

for all types of testers!

DoPE is one of the

powerful instruments

which supports DOLI

customers

Use our high level

programms and systems

and use your time to

develope -- in what your

customer is interested in:

Your Application Software!

DoPE DLL

YYYooouuurrr AAAppppppllliiicccaaatttiiiooonnn

SSSoooffftttwwwaaarrreee

DPX safety protocol for USB or Ethernet

DPX safety protocol for USB or Ethernet

DOLI Subsystem for data acquisition and closed loop control for testing instruments

DCxx

DOLI Digital DC Power Amplifier xx

ON

TEST

STOP

7 8 9

4 5 6

1 2 3

0 , -/+ F2 F3 F1

EDC580V

dope_short_en.doc

DoPE

EDC220√, EDC222√,

EDC580√

Full stand alone systems for all type of material testing instruments. Excitation and A/D-conversion of transducers as well as complete digital control of the connected drive are included. Load resolutions and options:

EDC220V

EDC222V: ±180,000 Steps Two option slots

EDC580V: ±180,000 Steps With 4ETF or 4FAD. Seven additional option slots

Drives

The following appliances are available as standard power amplifiers for DC motors:

12W, 160W and 320W inside the EDC housing.

1,100W in separate housing, same size as EDC

2,500W extended separate housing.

Further drives

AC-drives are contolled via the 10V-output or digitally.

Servo valve amplifiers.

DOLI Elektronik GmbH Adi-Maslinger-Straße 7 81373 München / Germany Tel: (+49)-0-89-20 243-0 Fax: (+49)-0-89-20 243 243 e-mail: sales@doli.de Internet: www.doli.de

Tasks of DoPE

The subsystem is initialised according to the predefined setup data.

Application program measur ing data is given in SI-units (N, m etc.).

A wide range of machine movement commands are offered, including simple and complex commands.

Events like limit switch etc. are reported.

DoPE is a 32 bit DLL. A simple command could be:

“move up in position control with 10mm/min“.

A complex command could be: “move in position control with 100mm/min to 500N and keep 500N in load control“.

A cycling command could be: “do 100 sinusoidal load cycles with an amplitude of 100N with 3Hz.“

Initialising

The subsystem software is able to handle up to:

16 logical measuring channels

10 logical analogue output channels

10 logical bit input devices

10 logical bit output devices

logical measuring channels

0 = Xhead position

1 = Load

2 = Extension

3 = Temperature

4 = xxx

EDC220V/222V/ 580V connectors

X4

X7

X21

X22

X23

DOLI produces electronics for testing instruments since 1979. The first digital contoller was presented in 1984. About 16,000 digitally controlled DOLI systems are running worldwide in 2003. 95% of the production is delivered to producers of instruments worldwide. DOLI supplies electronics, drives, application software and has enough know-how to support and design custom made systems for producers in the field of testing equipment and retrofits.

The assignment of physical to logical channels has to be done during the system initialisation. DoPE can use the EDC setup for this assignment. The custumer application program is able to modify the EDC setup data, also. An assignment has to be specified with the connector number, the logical measuring channel and some transducer specific data. All setup data will be stored in the file system inside the EDC.

Visit our web page www.doli.de

Videx_short_en.doc

Videoextensometer

Longitudinal and transversal strain – in real-time and non-contacting!

RTSS – The star in the sky of strain measurement!

RTSS – Real Time Strain Sensor – DOLI is your partner!

RTSS - the Videoextensometer for your tension tests

The RTSS is a non-contacting one-camera measurement system to be used with testing instruments. It offers real-time-image-processing and a modern, configurable and intuitive user surface – the RTSS Control&Analysis Software! The software comes with pre-defined templates for different applications.

As mentioned above, the RTSS works in a non-contacting manner. Hence, it perfectly fits for strain detection during tests inside a temperature chamber:

You just fix your markers to the sample and start the test – the RTSS “monitors from outside”.

Videoextensometer and EDC communicate via a serial interface. The strain signal of the RTSS will be handled like any other analogue input signal. This way, even a strain control is possible via the RTSS Videoextensometer.

You do static tests? We have the right thing for you:

The RTSS_HR works accurately!

The RTSS_HR „High resolution“ is a videoextensometer for high-precision data aquisition. Its resolution of 0.002% strain is being ammended by the good data acquisition rate of up to 70Hz.

You do dynamic tests? No problem as well:

The RTSS_HS works fast!

Nothing escapes the RTSS with its data acquisition rate of up to 4kHz. The RTSS_HS „High speed“ perfectly fits for your dynamic cycle tests, for hydropulsers or shakers. At the same time, it offers a resolution of up to 0.02% strain.

RTSS_HR RTSS_HS

Resolution approx. 0.002% approx. 0.02%

Detection rate approx. 70Hz up to 4KHz

There is more to it than that!

With alternative objective lenses, the videoextensometer can be fitted perfectly to your needs.

Non-contacting measuring system

For tests under extreme environmental conditions

Real-time measurement

Fast and efficient tests

High resolution – up to 0.002% strain

Accurate detection of material characteristics

High detection rate – up to 4kHz

Perfect for dynamic tests

Easy handling - controlled by the EDC

Fully automated operation possible

Strain control via RTSS

Intuitive user surface

Pre-defined templates for different applications

Videx_short_en.doc

Videoextensometer

System overview RTSS

Visit our website www.doli.de

Advantages

Detection of longitudinal strain, transversal strain and contraction

Fully automated operation due to control via the EDC

Modern, configuable and intuitive user surface

Pre-defined templates for different tasks

Integrated generation and storage of image sequences

Multithread-analysis-kernel supports multicore processors for a smaller processor load

Serial communication to the EDC

Strain control possible via RTSS

Two different models for your best results

High-quality objective lenses for special applications

Different mounting sets for different camera positions

Special system configurations for special measuring tasks!

DOLI Elektronik GmbH

Adi-Maislinger-Straße 7 81373 München/Germany Tel: (+49)-0-89-20 243-0 Fax: (+49)-0-89-20 243-243 E-Mail: sales@doli.de Internet: www.doli.de

Characteristics

The videoextensometer is used to detect longitudinal and transversal strain at tension tests in a non-contacting manner. It offers pre-defined templates for different applications, such as the detection of crack length (e.g. with long-time-tests) or crack surfaces (e.g. with adhesive sealings).

It is used to detect material characteristics during a tensile test. It detects (non-contacting) the sample deformation and uses these values to determine e.g. the ‘load/strain’-curves or the ‘load/stress’-curves for determination of the Young’s Modulus and the Poisson’s Ratio.

The multithread-analysis-kernel supports multicore processors for a smaller processor load. Hence, it is possible to install the system to the PC of the testing instrument.

A wide range of accessories expand the field of application – and a robust case protects the camera and the accessories from being damaged.

Technical specifications

‚High resolution‘ RTSS_HR

‚High speed‘ RTSS_HS

Resolution 0.002% strain 0.02% strain

Maximum detection rate 70Hz 4.000Hz

Accuracy of displacement

1μm at 100mm field of view (FOV)

10μm at 100mm field of view (FOV)

Measuring range 0.002% ... 1000% 0.02% ... 1000%

Resolution 2.0 Megapixel VGA 640x480 Pixel

Strain rate >500% >500%

Optional analogue output ±10V, 16Bit ±10V, 16Bit

Measurements

Detection of longitudinal strain via sample markers

Detection of transversal strain via the sample geometry

Detection of lateral contraction via the sample diameter

Detection of material characteristics - like Young’s Modulus, Poisson’s ratio etc.

Realisation of strain-controlled tensile tests

Tearing tests

Strain behaviour at dynamic tensile tests

Dynamic and high-speed tests

Vibration analysis

aso.

RTSS (Real Time Strain Sensor) is a non-contacting optical measurement

system based on a digital camera and real-time-image-processing. It measures

the longitudinal and transversal strain between two line markers, that have been

fixed to the sample surface. It works with a maximum rate of 4,000Hz. The strain

values will be sent to the tester, either as analogue or digital signal.

pcinc_short_en.doc

PCINC / PC104

PC board for direct data acquisition of

four rectangle and sinusoidal incremental transducer signals

The PC board PCINC enables the direct connection of up to four incremental sensors (incremental transducer, linear scale) to the PC. In comparison with an external electronics, this is a space saving and cost effective solution (an external electronics additionally needs its own box, power supply, mains cable and data cable). Technical advantages are e.g. shorter delay time, better real-time capability and more, simpler ways to assure the EMC-compatibility. Furthermore, DOLI Elektronik has build in some special features, such as synchronised measure-ment etc., that won’t be recog-nized with the first look. In many cases, a direct data translation between measurement system and PC bears advantages. Especially for the Quality Assurance division, where

measurement data have to be controlled continuously at the PC, the PC boards turned out to be a significant improvement.

System Overview PCINC is a short ISA- or PCI-Bus-PC-board with up to four 9pole-SUBD-sockets or 15pole-SUBD-plugs for the direct connection of four incremental transducers and one optional socket for the supply of a trigger signal for each of these four channels. The PCINC needs an ISA- or PCI slot in the PC and will be addressed via the IO-virtual address space. The basic address can be set in a DIP-switch.

The Windows driver program enables the automatic recognition of one or more PCINC boards in the PC, hence enabling the direct access to the functions of the board.

PCINC4 – state-of-the-art board with 8 additional I/Os

Very fast forward/backwards counters ( 32MHz counter frequency)

High speeds and acquisition of large travels

Synchronized data acquisition of all channels, measurement value and reference pulse

Interpolation of sinusoidal signals up to factor 1000

Short PC-Board

Configurable

to 11A or 1 Volt sinusoidal or RS422-rectangular Signal

With ISA or PCI Bus

Synchronisation logics

Voltage supply +5V for the incremental transducers.

DOLI Elektronik . . . for measurement and motion !

PCINC4 – Direct connection of four incremental transducers to a PC

pcinc_short_en.doc

PCINC / PC104

Visit our homepage www.doli.de

DOLI Elektronik GmbH

Adi-Maislinger-Straße 7 81373 München/Germany Tel: (+49)-0-89-20 243-0 Fax: (+49)-0-89-20 243-243 e-mail: sales@doli.de Internet: www.doli.de

PC104-Board for the direct connection of two Incremental Transducers

The new PC104-board enables the connection and processing of

incremental sine signals (11A or 1V) as well as incremental rectangle signals (signal level RS422) coming from different position measure-ment systems directly to the PC without the need of using an external transducer electronics. The user configures the wanted input signal independent for each measuring channel.

The board has two forward/backwards counters, two data registers, two reference registers and two interpolators. The interpolation can reach a value of 1,000 and more, depending on the quality of the input signals. The factor will be set per software.

The PC104-board supplies the incremental transducers with the supply voltage of +5V.

PCINC4 Advantages

Synchronisation Logics. The counter counts of the channels are written into the particular measurement value latch simultaneously. This means, that even with high speeds precise synchronised monitoring between channels or precise XYZ-track measurements are possible. Furthermore, the synchronisation of numerous PCINC boards (several measurement channels synchronized) is possible.

Evaluation of the incremental signals (track A, track B, refe-rence): directional recognition and

four-fold evaluation.

Reference value acquisition without time delay. In addition to the measurement value latch, a reference latch is available for each channel. The configuration, whether the reference signal or the optional trigger signal should have an effect on this latch, happens via software. This arrangement enables a transpa-rent acquisition of the reference marks on a linear graduation or the precise position acquisition even at high traverse travel speeds.

Boards available Accessories

Ord.No Characteristics

1655 PCINC4, 3 channels, PCI-Bus, 2xSUBD9-socket

Slot sheets for the third channel and the digital IOs

1656 PCINC4, 3 channels, PCI-Bus, 2xSUBD15-plug

Slot sheets for the third channel and the digital IOs

1658 PCINC4, 3 channels, PCI-Bus, 2xSUBD15-socket

Slot sheets for the third channel and the digital IOs

1660 PCINC4, 4 channels, PCI-Bus, 2xSUBD9-socket

Slot sheet for the third and fourth channel and cable for the digital IOs

1661 PCINC4, 4 channels, PCI-Bus, 2xSUBD15-plug

Slot sheet for the third and fourth channel and cable for the digital IOs

1662 PCINC4, 4 channels, PCI-Bus, 2xSUBD15-socket

Slot sheet for the third and fourth channel and cable for the digital IOs

1557 PC104, 2 channels, PC104-Bus Fitting cable, 2 pieces necessary 1593 Cable without slot sheet,

1x SUBD9-socket

PCINC Data

Dimensions 145x105mm

PC-board ISA, PCI

Power consumption 1.5W without sensors

Data range per channel 32 bit

Driver Software dll für C++

DEMO Software WIN98 and higher in C

Signal division up to 1024 fold up to 1024 fold 4 fold

Input frequency max. 100kHz max. 500kHz max. 6MHz

Sensor input up to 4x sin 11A up to 4x sin 1 Vss up to 4x

rect RS422

12 firmen_praes_long_en.doc

DOLI OEM Products are compatible amongst themselves!

If you have developed (or adapted your existing) software for a DOLI electronics system once,

you can connect to a new DOLI product very fast.

EDC5/25, EDC100, EDC60, EDC120, EDC220, EDC222, EDC580,

EDC220V, EDC222V, EDC580V and the following products.

You choose the desired electronics with the exact resolution and the exact price for the exact application

for your best profit.

Worldwide, approx. 33,000 digital controlled testing instruments

are running with DOLI controllers !