Post on 07-Apr-2018
8/6/2019 6 - Sealing and Soundproofing
1/15
Renault s.a.s 2008
"The repair methods given by the manufacturer in this document are based on the technical
specifications current when it was prepared.
The methods may be modified as a result of changes introduced by the manufacturer in theproduction of the various component units and accessories from which his vehicles areconstructed."
All copyrights reserved by Renault.
The reproduction or translation in part of whole of the present document, as well as the useof the spare parts reference numbering system, are prohibited without the prior writtenconsent of Renault.
JULY2008 Edition Anglaise
X95
6 Sealing and soundproofing
65A OPENING ELEMENT SEALING
66A WINDOW SEALING
68A SOUNDPROOFING
8/6/2019 6 - Sealing and Soundproofing
2/15
MEGANE III - Section 6
Contents
Page
MEGANE III- Section 6ContentsPage
65A OPENING ELEMENT SEALING
Door sealing film: Removal -Refitting 65A-1
Sunroof seal: Removal -Refitting 65A-4
66A WINDOW SEALING
Front side door glass runchannel: Removal - Refitting 66A-1
Front door side exteriorweather strip: Removal -Refitting 66A-3
Glass run channel in rearside door: Removal -Refitting 66A-4
68A SOUNDPROOFING
Centre floor sidesoundproofing: Removal -Refitting 68A-1
Centre floor rear
soundproofing: Removal -Refitting 68A-3
8/6/2019 6 - Sealing and Soundproofing
3/1565A-1
OPENING ELEMENT SEALING
Door sealing film: Removal - Refitting 65AREMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove the front side door trim (see Front side
door trim: Removal - Refitting) (72A, Side openingelements trim) or the rear side door trim (see Rearside door trim: Removal - Refitting) (72A, Sideopening elements trim).
II - OPERATION FOR REMOVAL OF PARTCONCERNED
Front door
Rear door
a Start removing the upper section of the door sealing
film (1) .
134167
137317
8/6/2019 6 - Sealing and Soundproofing
4/1565A-2
OPENING ELEMENT SEALING
Door sealing film: Removal - Refitting 65Aa Carefully remove the mastic bead from the door box
section around the edges of the door sealing film.
REFITTING
I - REFITTING PREPARATION OPERATION
a parts always to be replaced: Door sealing film(60,03,02,10).
II - REFITTING OPERATION FOR PARTCONCERNED
Front door
Rear door
a Remove the paper protecting the door sealing filmmastic bead.
a Offer up the door sealing film without forcing it, brin-ging it into contact with the areas shown (2) .
Note:
If the mastic bead offers too much resistance,use a hot air gun set to approximately 100C andheld approximately 20 cm away from the doorsealing film to ease its removal.
Note:
Remove the adhesive residue from the door boxsection by applying wide masking tape over thebonding area. Pull gently on the masking tape toremove any adhesive residue.
Clean the door box section using a lint-free clothsoaked in HEPTANE (see Vehicle: Parts andconsumables for repair) (04B, Consumables -Products).
WARNING
The door must be clean (free of dust, grease,anti-adhesive products), with no trace of impuri-ties and no condensation. The area of the innerdoor panel where the film is applied must bepainted completely.
Adhesive surfaces should be at a minimum tem-perature of 15 in order for the film to adhere pro-perly to the door.
134167
137317
Note:
Do not touch the mastic bead.
8/6/2019 6 - Sealing and Soundproofing
5/1565A-3
OPENING ELEMENT SEALING
Door sealing film: Removal - Refitting 65Aa Position the door sealing film correctly around the
outside edge without applying any pressure.
a Firmly attach the door sealing film around its entireedge.
III - FINAL OPERATION
a Carry out a sealing test (see Technical Note0653A).
a Refit the front side door trim (see Front side doortrim: Removal - Refitting) (72A, Side opening ele-ments trim) or the rear side door trim (see Rear sidedoor trim: Removal - Refitting) (72A, Side openingelements trim).
8/6/2019 6 - Sealing and Soundproofing
6/1565A-4
OPENING ELEMENT SEALING
Sunroof seal: Removal - Refitting
B95, and PANORAMIC SUNROOF
65A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the mobile sunroof panel (see Sunroofmoving panel: Removal - Refitting) (52A, Non-side opening element mechanisms).
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the sunroof seal (1) .
REFITTING
I - REFITTING PREPARATION OPERATION
a Always replace the sunroof seal.
a Clean the bonding area with HEPTANE (see Vehi-cle: Parts and ingredients for the repairwork)(04B, Consumables - Products).
II - REFITTING OPERATION FOR PARTCONCERNED
a Position the sunroof seal joint at the rear central sec-tion (2) .
a Bond the sunroof seal using SPECIAL ADHESIVEFOR WINDOWS (see Vehicle: Parts and ingre-dients for the repairwork) (04B, Consumables -Products).
III - FINAL OPERATION
a Refit the mobile sunroof panel (see Sunroof mo-
ving panel: Removal - Refitting) (52A, Non-sideopening element mechanisms).
137487
137487
8/6/2019 6 - Sealing and Soundproofing
7/1566A-1
WINDOW SEALING
Front side door glass run channel: Removal - Refitting 66AREMOVAL
I - REMOVAL PREPARATION OPERATION
a Remove:
- the door mirror (see Door mirror: Removal - Re-fitting) (56A, Exterior equipment),
- the front side door trim (see Front side door trim:Removal - Refitting) (71A, Side opening elementstrim),
- the door sealing film (see 65A, Opening elementsealing, Door sealing film: Removal - Refitting,page 65A-1) ,
- the front side door sliding window (see Slidingwindow in front side door: Removal - Refitting)
(54A, Windows),- the front side door pillar exterior trim (see Frontside door pillar exterior trim Removal - Refit-ting) (55A, Exterior protections).
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Detach the front side door glass run channel (1) .
a Detach the front side door glass run channel at (2) ,(3) and (4) .
a Remove the front side door glass run channel.
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Fit the glass run channel, starting with the rear uppersection (4).
a Refit the front side door pillar exterior trim (see Frontside door pillar exterior trim Removal - Refitting)(55A, Exterior protection).
a Fit the centre (3)front (2)and rear sections (1)of theglass run channel.
II - FINAL OPERATION
a Refit:
- the front side door sliding window (see Slidingwindow in front side door: Removal - Refitting)(54A, Windows),
- the door sealing film (see 65A, Opening elementsealing, Door sealing film: Removal - Refitting,page 65A-1) ,
- the front side door trim (see Front side door trim:
Removal - Refitting) (71A, Side opening elementstrim),
- the door mirror (see Door mirror: Removal - Re-fitting) (56A, Exterior equipment).
137382
134129
8/6/2019 6 - Sealing and Soundproofing
8/1566A-2
WINDOW SEALING
Front side door glass run channel: Removal - Refitting 66Aa Carry out a function test.
8/6/2019 6 - Sealing and Soundproofing
9/1566A-3
WINDOW SEALING
Front door side exterior weather strip: Removal - Refitting 66A
REFITTING
I - REMOVAL PREPARATION OPERATION
a Lower the front side sliding door window.
II - REFITTING OPERATION FOR PARTCONCERNED
a Carefully remove the front side exterior door wea-therstrip (1) using the (Car. 1363).
REFITTING
I - REFITTING PREPARATION OPERATION
a Index the front side exterior door weatherstrip.
II - REFITTING OPERATION FOR PARTCONCERNED
a Refit the front side door exterior weatherstrip.
a Check that the front side exterior door weatherstripis correctly aligned.
III - FINAL OPERATION
a Raise the front side sliding door window.
Essential special toolingEssential special too-lingEssential special tooling
Car. 1363 Set of trim removal levers.
134168
8/6/2019 6 - Sealing and Soundproofing
10/1566A-4
WINDOW SEALING
Glass run channel in rear side door: Removal - Refitting
B95
66A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLower the rear side sliding door window to the lowposition.
a Remove:
- the rear side door trim (see Rear side door trim:Removal - Refitting) (72A, Side opening elementtrim),
- the sealing film (see 65A, Opening element sea-ling, Door sealing film: Removal - Refitting,page 65A-1) ,
- the rear side door interior weatherstrip.
a Wind the rear side door sliding window down to thebottom of the door box section (see Sliding windowin rear side door: Removal - Refitting) (54A, Win-dows).
a Remove:
- partially the rear side door glass run channel (1) ,
- partially the exterior weatherstrip (2) .
a Remove the rear side door pillar exterior trim (seeRear side door pillar exterior trim Removal - Re-
fitting) (55A, Exterior equipment).
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Detach the rear side door glass run channel at (3) .
a Remove the rear side door glass run channel -fixed window - exterior weatherstrip assembly.
137390
134169
137379
8/6/2019 6 - Sealing and Soundproofing
11/1566A-5
WINDOW SEALING
Glass run channel in rear side door: Removal - Refitting
B95
66A
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the rear side door glass run channel - fixedwindow - exterior weatherstrip assembly.
a Fit the rear side door glass run channel at (4) .
a Position the sections of the rear side glass run chan-
nel inside the door box section.
a Fit the rear section of the rear side door glass runchannel
II - FINAL OPERATION
a Refit:
- the rear side door pillar exterior trim (see Rear side
door pillar exterior trim Removal - Refitting)(55A, Exterior equipment),
- the rear side door sliding window at the bottom ofthe door box section (see Sliding window in rearside door: Removal - Refitting) (54A, Windows),
- the rear side door interior weatherstrip,
- the exterior weatherstrip (2).
- the sealing film (see 65A, Opening element sea-ling, Door sealing film: Removal - Refitting,page 65A-1) ,
- the rear side door trim (see Rear side door trim:Removal - Refitting) (72A, Side opening elementtrim).
a Carry out a function test.
137379
8/6/2019 6 - Sealing and Soundproofing
12/1568A-1
SOUNDPROOFING
Centre floor side soundproofing: Removal - Refitting
B95 or D95
68A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Disconnect the battery (see Battery: Removal - Re-fitting) (80A, Battery).
a Remove:
- the complete front seats (see Complete frontseat: Removal - Refitting) (75A, Front seat fra-mes and runners),
- the centre console (see Centre console: Removal- Refitting) (57A, Interior equipment),
- the single unit rear bench seat base (see Singleunit rear bench seat: Removal - Refitting) (76A,
Rear seat frames and runners),
- the 1/3 and 2/3 rear bench seat base (see 1/3 and2/3 rear bench seat:Removal - Refitting) (76A,Rear seat frames and runners),
- the floor storage compartment and flap (see Floor
flap and storage: Removal - Refitting) (57A, Inte-rior equipment).
a Remove:
- the front door sill lining (see Front door sill lining:Removal - Refitting) (71A, Body internal trim),
- the rear inner sill trim (see Rear door sill lining:Removal - Refitting) (71A, Body internal trim),
- the rear inner sill upper trim (see Rear door sill up-per lining: Removal - Refitting) (71A, Body inter-nal trim),
- the B-pillar lower trim (see B-pillar lower trim: Re-moval - Refitting) (71A, Body internal trim).
a Remove:
- the door sill lining (see Door sill lining: Removal -
Refitting) (71A, Body internal trim),
- the rear panel trim (see Rear panel trim: Removal- Refitting) (71A, Body internal trim).
a Remove the floor carpet (see Floor carpet: Remo-val - Refitting) (71A, Body internal trim).
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove clip (1) .
a Remove the air duct .
a Remove the clips (2) .
a Remove the centre floor side soundproofing.
B95
D95
136657
136655
8/6/2019 6 - Sealing and Soundproofing
13/1568A-2
SOUNDPROOFING
Centre floor side soundproofing: Removal - Refitting
B95 or D95
68A
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit:
- the centre floor side soundproofing,
- the clips (2),
- the air duct,
- the clip (1).
II - FINAL OPERATION
a Refit the floor carpet (see Floor carpet: Removal -
Refitting) (71A, Body internal trim).
a Refit:
- the rear panel trim (see Rear panel trim: Removal- Refitting) (71A, Body internal trim),
- the door sill lining (see Door sill lining: Removal -Refitting) (71A, Body internal trim).
a Refit:
- the B-pillar lower trim (see B-pillar lower trim: Re-moval - Refitting) (71A, Body internal trim),
- the rear inner sill upper trim (see Rear door sill up-per lining: Removal - Refitting) (71A, Body inter-nal trim),
- the rear inner sill trim (see Rear door sill lining:Removal - Refitting) (71A, Body internal trim),
- the front sill panel trim (see Front door sill lining:Removal - Refitting) (71A, Body internal trim).
a Refit:
- the floor storage compartment and flap (see Floorflap and storage: Removal - Refitting) (57A, Inte-
rior equipment),- the 1/3 and 2/3 rear bench seat base (see 1/3 and2/3 rear bench seat:Removal - Refitting) (76A,Rear seat frames and runners),
- the single unit rear bench seat base (see Singleunit rear bench seat: Removal - Refitting) (76A,Rear seat frames and runners),
- the centre console (see Centre console: Removal
- Refitting) (57A, Interior equipment),
- the complete front seats (see Complete frontseat: Removal - Refitting) (75A, Front seat fra-mes and runners).
a Connect the battery (see Battery: Removal - Refit-ting) (80A, Battery).
D95
B95
8/6/2019 6 - Sealing and Soundproofing
14/1568A-3
SOUNDPROOFING
Centre floor rear soundproofing: Removal - Refitting
B95 or D95
68A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Disconnect the battery (see Battery: Removal - Re-fitting) (80A, Battery).
a Remove:
- the complete front seats (see Complete frontseat: Removal - Refitting) (75A, Front seat fra-mes and runners),
- the centre console (see Centre console: Removal- Refitting) (57A, Interior equipment),
- the single unit rear bench seat base (see Singleunit rear bench seat: Removal - Refitting) (76A,
Rear seat frames and runners),
- the 1/3 and 2/3 rear bench seat base (see 1/3 and2/3 rear bench seat:Removal - Refitting) (76A,Rear seat frames and runners),
- the floor storage compartment and flap (see Floor
flap and storage: Removal - Refitting) (57A, Inte-rior equipment).
a Remove:
- the front door sill lining (see Front door sill lining:Removal - Refitting) (71A, Body internal trim),
- the rear inner sill trim (see Rear door sill lining:Removal - Refitting) (71A, Body internal trim),
- the rear inner sill upper trim (see Rear door sill up-per lining: Removal - Refitting) (71A, Body inter-nal trim),
- the B-pillar lower trim (see B-pillar lower trim: Re-moval - Refitting) (71A, Body internal trim).
a Remove:
- the door sill lining (see Door sill lining: Removal -
Refitting) (71A, Body internal trim),
- the rear panel trim (see Rear panel trim: Removal- Refitting) (71A, Body internal trim).
a Remove the floor carpet (see Floor carpet: Remo-val - Refitting) (71A, Body internal trim).
II - OPERATION FOR REMOVAL OF PARTCONCERNED
a Remove the rear floor soundproofing.
REFITTING
I - REFITTING OPERATION FOR PARTCONCERNED
a Refit the rear floor soundproofing.
II - FINAL OPERATION
a Refit the floor carpet (see Floor carpet: Removal -Refitting) (71A, Body internal trim).
a Refit:
- the rear panel trim (see Rear panel trim: Removal- Refitting) (71A, Body internal trim),
- the door sill lining (see Door sill lining: Removal -Refitting) (71A, Body internal trim).
a Refit:
- the B-pillar lower trim (see B-pillar lower trim: Re-moval - Refitting) (71A, Body internal trim),
- the rear inner sill upper trim (see Rear door sill up-per lining: Removal - Refitting) (71A, Body inter-nal trim),
- the rear inner sill trim (see Rear door sill lining:Removal - Refitting) (71A, Body internal trim),
- the front sill panel trim (see Front door sill lining:Removal - Refitting) (71A, Body internal trim).
a Refit:
- the floor storage compartment and flap (see Floorflap and storage: Removal - Refitting) (57A, Inte-rior equipment),
- the 1/3 and 2/3 rear bench seat base (see 1/3 and2/3 rear bench seat:Removal - Refitting) (76A,
Rear seat frames and runners),- the single unit rear bench seat base (see Single
unit rear bench seat: Removal - Refitting) (76A,Rear seat frames and runners),
B95
D95
D95
B95
8/6/2019 6 - Sealing and Soundproofing
15/15
SOUNDPROOFING
Centre floor rear soundproofing: Removal - Refitting
B95 or D95
68A
- the centre console (see Centre console: Removal- Refitting) (57A, Interior equipment),
- the complete front seats (see Complete frontseat: Removal - Refitting) (75A, Front seat fra-
mes and runners).
a Connect the battery (see Battery: Removal - Refit-ting) (80A, Battery).