ADIRONDACK CHAIR (COUNTER HEIGHT) Materials List: Hardware: (4) 1x2x8 2” wood screws (3) 1x3x8 1 ¼” pocket hole screws (2) 1x4x8 1 ¼” wood screws (1) 1x5x6 2” pocket hole screws (1) 1x6x6 (2) 2x2x6 18” of a 2x4 scrap Cut List: (1) 1x5 @ 22 1/4” (foot rest) (2) 1x4 @ 30” (foot rest rails, one end 10º angle) (1) 1x3 @ 17 3/4” (foot rest front apron) (1) 1x4 @ 19 1/4” (back stretcher) (2) 1x4 @ 27” (arm rest) (2) 1x3 @ 20 1/2” (arms) (1) 2x4 @ 17 3/4” (bottom back support) *SEE CUT DIAGRAM (1) 1x5 @ 24 1/4” (middle back support) *SEE CUT DIAGRAM (1) 1x4 @ 19” (top back support) *SEE CUT DIAGRAM (2) 2x2 @ 30” (front legs – both ends cut at 5º angle, parallel) (2) 2x2 @ 30” (back legs – both ends cut at 10º angle, parallel) (2) 1x6 @ 24 1/2” (seat side supports) *SEE CUT DIAGRAM (13) 1x2 @ 19 1/4” (seat slats) (2) 1x3 @ 28” (back slats) (2) 1x3 @ 30” (back slats) (3) 1x3 @ 31” (back slats)  FOLLOW  CUT  DIAGRAMS  BELOW  FOR  CURVED  PORTIONS:    

 MAKE  2  SEAT  SIDE  SUPPORTS    

 

 

 

   STEP  1:  Attach  arms  to  front  leg  using  2”  countersunk  screws.    Make  two  opposing  sets.    

   STEP  2:  Assemble  lower  stretcher.    Attach  foot  rest  side  rails  to  back  stretcher  using  1  ¼”  pocket  hole  screws.    

   STEP  3:  Attach  lower  stretcher  to  legs  using  2”  countersunk  wood  screws.  

   STEP  4:  Attach  foot  rest  front  apron  to  side  rails  using  1  ¼”  pocket  hole  screws.    

   STEP  5:  Attach  seat  side  supports  to  legs  using  2”  countersunk  screws.    

   STEP  6:  Attach  back  middle  support  to  arms  using  1  ¼”  pocket  hole  screws.    Then  attach  to  back  leg  using  2”  countersunk  wood  screws.    

   STEP  7:    Attach  arm  rests  to  arm  and  back  middle  support  using  1  ¼”  countersunk  screws  from  underside.    

   STEP  8:  Attach  foot  rest  to  rails  using  1  ¼”  countersunk  screws.    Attach  seat  slats  to  supports  using  1  ¼”  countersunk  screws.    

   Use  a  jigsaw  to  cut  curve  into  back  slats  before  assembly.  

   STEP  9:  Attach  back  slats  to  back  bottom  support  using  (1)  1  1/4”  countersunk  wood  screw  at  center  of  each  board.    

   STEP  10:  Attach  back  bottom  support  to  seat  side  support  rails  using  2”  pocket  hole  screw.    Adjust  back  slats  to  fan  out  and  rest  against  back  middle  support.    Attach  to  back  middle  support  using  1  ¼”  countersunk  screw  from  front.    

   STEP  11:  Attach  back  top  support  to  back  slats  if  desired.    Use  1  ¼”  countersunk  wood  screws  from  front.