Mission Furniture
Thank You!Thank you for ordering a WOOD® magazine download. We hope you enjoy being part of our online experience and that you have fun expanding your woodworking skills.
Please remember that this copyrighted material is for your use only. It is unlawful to share this file with someone else or to reprint it in any form.
Bill KrierEditor in Chief, WOOD magazine
Adobe Acrobat Reader Troubleshooting Guide
If you can read this page, your Acrobat Reader program is working correctly! But you may still have problems or specific issues, such as printing and saving your downloadable file.
My printer won’t print the text correctlyAlmost all printing problems are due to not enough free system resources memory. The files are very memory intensive because they include graphics, text, and photos. Close all other programs/applications and print directly out of the Acrobat Reader program, not your Web browser.
Patterns are not printing full-sizeMake sure your printer is set to print at 100 percent and that “print to fit” is not checked. These settings are selected in the printer setup or printer options.
I can’t save my file now that it’s downloadedYou must save the plan when you download the file. Download the file again, except this time try right-clicking on the red download button. A menu window will open. Select “Save target as” or “Save link as” to save the file to your hard drive. Once saved, you can open it up with Adobe Acrobat Reader.
For more details on using Adobe Acrobat Reader please visit our online help section at: http://www.woodstore.net/clicherforde.html
WOOD Store Customer Favorites
WOODStore.net Browse more than 1000 plans, projects, books, techniques, & more
Visit the WOOD Store at:
WOODStore.net
Shop Tools & Accessories
Indoor Furniture
Outdoor Furniture
http://www.woodmagazine.com
DOWNLOADABLE ONLINE WOODWORKING PLANS
®
Page 1 of 8
3-drawer utility cabinet
DP-00275 ©Copyright Meredith Corporation 2003
Inexpensive materials and
basic joinery make for
speedy construction of this
hardworking shop cabinet.
Even the drawers won’t
slow you down. With their
special side/slide
hardware, they practically
build themselves.
Page 2 of 8TM
If saving time and money isimportant to you, you’ll reallyappreciate the drawer hardwareused in this project. Costing littlemore than standard slides, thisepoxy-coated steel hardwarecombines both drawer side andslide in one piece. For more onthis innovative hardware, see“Make the fastest drawers in thewest (or east)” on page 6.
Start with the case1 Cut the stiles (A), side rails (B),front rails (C), and back rail (D) tothe sizes listed in the MaterialsList. With a dado blade adjusted tomatch the thickness of the fi"plywood side panels (E), cutcentered grooves in parts A, B, andD, where shown on Drawing 1.Then cut the ‹"-deep rabbet alongthe top edge of the lower front rail(C) and the fi" notches ‡" deep inboth front rails. Now cut therabbets in the stiles (A). Finish-sand all the parts to 180 grit.2 Cut the side panels (E) to thesize listed. Glue and clamp thestiles and rails (A, B) to the sidepanels, checking the assemblies forsquare.3 Cut the bottom (F) and back (G)to the sizes listed. Cut the ‹×fi"notches in the back’s top corners.4 Retrieve the lower front rail (C),and glue and clamp it to the bottom(F), keeping the ends flush.Retrieve the back rail (D), and glueand clamp it, centered, on the back(G). Now, clamp the back to thebottom as shown, and drill screwholes through the back and into thebottom. Drive the screws.5 Place the first side assembly(A/B/E) flat on a horizontal surface.Squeeze a bead of glue on the sidepanel along the rear stile and thelower side rail. Place thebottom/back assembly (C/F/D/G)on the side assembly, and clamp itin place. Now drill angledcountersunk screw holes throughthe bottom and back and into therear stile and the lower side rail.Drive the screws.6 Apply glue to the upward-facingedges of the bottom and back
panels. Position the second sideassembly, and clamp it in place.Turn the cabinet over. Then, asbefore, drill angled countersunkscrew holes, and drive the screws.7 Clamp the upper front rail (C)in place. Drill angled countersunkscrew holes through the front railand into the side rails (B). Drivethe screws.8 Cut two ‡×21fi×25fi" piecesof medium-density fiberboard(MDF) for the top (H). Glue andclamp them together, keeping theends and edges flush. Sand the
edges smooth, and rout ¤" round-overs along all the edges.9 Cut the mobile base (I) to size,and rout ¤" round-overs along thetop and bottom edges. Using acaster’s mounting plate as agu ide , mark mounting-holelocations at all four corners. Drill‹" holes and countersink them onthe panel’s top face.
See the Dual-Purpose Sanding Center download to learn howto combine this three-drawer cabinet with a flip-top cabinet anda mobile base to create the multifunction work center, above.
AA
TM
Page 3 of 8
¸" shank hole,countersunk
on bottom face
E
AA
A
E
C
F
J
M
¤" round-overs on all edges
17"
fi"
fi" groove ‹" deep, centered
‹ x fi" notch
21fi"
fi" rabbet‹" deep
24"20"
#8 x 1‹" F.H.wood screw
#8 x 1fi" F.H.wood screw
#8 x 1‹" F.H. wood screw
¸" shank hole, countersunk on bottom face
‹" lock nut
‹" flat washer
‹-20 F.H. bolt1‹" long
‹" hole, countersunk
4" locking swivel caster
N
L
fi" grooves‹" deep, centered
‡" rabbet‹" deep
23"23"
23"
N
N
#8 x 1" F.H.wood screws
¤" round-overs
¤" round-overson all edgesN
#8 x ‡" F.H. wood screw
18"
1fi"
21fi" 25fi"
J
8›"
6Í"
¸" shank hole, countersunk on bottom face
#8 x 1‹" F.H.wood screw
B
fi"
¸" shank hole,countersunk on front face
fi" notch‡" deep
I
G
K
K
2fi"
H
BD
N
C
B
1 EXPLODED VIEW
TM
Page 4 of 8
3¤"
10Œ"
18"
#8 x ‡" F.H.wood screw
#6 x fi" F.H.wood screw
fi"
Drawer slide
G
D
N
E
B
N
N
B
F
4 DRAWER SLIDE CLEATS FRONT SECTION VIEW
L
M
‰" hole
2fi"
7‡"
16‡"1‹"
ˇ" holes fi" deepon inside face
1‹"
7‡"
8›"
6Í"
3‹"
4¤"3¤"
Ø"
¤" round-overs
‰" hole
2›"
2fi"
2 DRAWER FRONTS PARTS VIEW(Inside face shown)
fi"
1"1fi"
fi"
3 DRAWER SLIDE SPACEREND VIEW
TM
Page 5 of 8
Add the drawers1 Cut the drawer backs (J),drawer bottoms (K), and drawerfronts (L, M) to size. Ease theedges of the bottoms and backswith a sanding block. Rout ¤"round-overs along the front andback edges of the drawer fronts.Drill the screw holes for the pulls,where shown on Drawing 2.Finish-sand the parts. Apply twocoats of satin polyurethane to thebottoms and backs and threecoats to the fronts, sandingbetween coats. Now, to assemblethe drawers using the metalside/slides, see pages 6 and 7.2 With the drawers made, cutthe cleats (N) to size. Mark thebottom front corner of each cleat,making sure you have threemirror-image pairs. Drillcountersunk screw holes throughthe cleats fi" up from theirbottom edges, where shown onDrawing 1.3 Make the drawer slide spacershown on Drawing 3 from 12"-long scraps of fi" plywood. Usingthe holes in the drawer slides’
cabinet members as guides, drillpilot holes in the cleats, as shownin Photo B.4 Cut two 2×18" pieces of scrapfor cleat positioning spacers. Usethem to position the top pair ofcleats (N), as shown in Photo C.Now trim the spacers to 10Œ",and then 3¤" to mount the middleand bottom pairs of cleats, whereshown on Drawing 4.
Finish and assemble1 Finish-sand the case and thetop. Apply two coats of satinpolyurethane to the case andthree coats to the top, sandingbetween coats.2 Place the top (H) upside downon a pair of sawhorses. Turn thecabinet upside down, center it onthe top, and clamp it in place.From the outside of the cabinet,drill angled countersunk screwholes through the side rails (B)and back rail (D) and into the top.Drive the screws.3 With the hardware shown onDrawing 1, bolt the casters to themobile base (I). Place the base on
the cabinet, drill countersunkscrew holes through the base andinto the lower side rails (B). Drivethe screws, and place the cabinetright side up on the floor.4 Attach the drawer slides’cabinet members to the cleats(N), driving the screws into thepreviously drilled holes. Fastenthe pulls to the drawer fronts, andslide the drawers into the cabinet.Adjust the drawer fronts to leave‹" between the top (H) and thetop drawer front, and ‰"between drawer fronts, leaving¤" between the bottom drawerfront and the mobile base.5 Center your benchtop tool onthe top, and mark the locations ofthe mounting holes. Drill theholes, and bolt the tool to the top.Roll the cabinet out of the way,set the caster brakes, and roundup some stuff to fill its drawers. ¿
Written by Jan SvecProject design: Jeff MertzIllustrations: Roxanne LeMoine
Use a spacer to position the drawer slide fi" down fromthe cleat’s top edge. With the slide’s front end ¤" fromthe cleat’s front edge, drill the pilot holes.
With their ends against the cabinet’sbottom, use a pair of 18"-long spacersto position the top cleats. Then glueand screw the cleats in place.
Bottomfront
Self-centeringdrill bit
Drawer slide spacer
¤"
fi"
N
BB
N
Spacers
CC
TM
Page 6 of 8
Initially developed for the commercial kitchen-cabinet trade, the all-in-one metal drawer side/slidehardware used in this project allows you to buildsturdy drawer boxes in record time. But that’s notits only advantage. The side/slide hardware costsabout the same as regular drawer slides alone whileeliminating the wood for drawer box sides andfronts. And, adjustable brackets attach the finished
J
Remove tabsbefore assembly.
15‡"
4‡"
16‡"
ˇ" hole fi" deep#10-32 x 1"R.H. machine screw
7⁄64" pilot hole ‹" deep
#8 x fi" panhead screw
Metal drawer side
#8 x 1‹" F.H. wood screw
¸" shank hole, countersunk
Drawer slide
21¤"
#8 x fi"panhead screw
Cardpull 15‡"
¤" round-overs
Drawer-front bracket
Clamping plate
,
K
#8 x ‡" F.H. wood screw
22"
N
#6 x fi" F.H. wood screw
¸" shank hole,countersunk
fi"
L M
Make the fastest drawers in the west (or east)
Step 1Drill screw holes and fasten the drawer back (J) to the drawerbottom (K), where shown on the drawing, above. Position the metal sides on the back/bottom assembly, drill pilot holes,and screw them in place, as shown in the photo, right. For easyassembly, a 12×18" scrapwood assembly frame 6" high holdsthe back and sides clear of your worktop.
DRAWER(Viewed from the back)
K
Assemblyframe
J
Removetabs.
Metalside
drawer fronts to the sides, allowing you to fine-tunethe gaps between drawers during final cabinetassembly. Here’s how to build a drawer using thistime- and money-saving hardware.Note: The metal sides have a pair of raised tabs (seedrawing below) used for positioning in mass-production applications. Clip off these tabs beforeassembling your drawers.
TM
Page 7 of 8
Step 2To accurately place the drawer-frontbrackets on both the small drawerfronts (L) and the large drawer front(M), make the drilling guide accordingto the drawing, below right. To avoidconfusion, draw brackets on both ofthe jig’s faces to connect the pairs ofholes for parts L and M, as shown.Mark the door front’s centerline on itsback face. Place the guide’s cleatagainst the front’s bottom edge, alignthe guide’s edge with the markedcenterline, and clamp it in place. Drillˇ" holes fi" deep, as shown in thephoto, right. Flip the jig, and repeat atthe drawer front’s other end. 9"ˇ" holes
‡ x ‡ x 9"cleat
‹" groove‹" deep,centered
7Ø"
2fi"
2fl"
ML
7"‹" tempered
hardboard
Part holesM
Part holesL
2fi"
3›"
DRAWER FRONT DRILLING GUIDE
MCenterline marked on
masking tape
Drillingguide
Stop collar
Cleat
Backof
Bottomedge of
M
Step 3With the bracket’s drawer-side flange tothe outside, drive its plastic inserts intotheir holes, as shown, below. Use a scrapof wood to evenly distribute the force.Loosely fasten the clamping plates to thebrackets with the provided machine screw.Slide the drawer sides between thebrackets and the clamping plates, as shown,below right, and tighten the screws.
MBack of
Drawer-frontbracket’s
drawer-side flange Plasticinsert
Metal drawer side
M
K
Clamping plate
Drawer-front bracket
TM
Page 8 of 8
Materials key: M–maple,MDO–medium-density overlay plywood,LMDF–laminated medium-densityfiberboard, MDF–medium-densityfiberboard.Supplies: #8ׇ", #8×1", #8×1‹",#8×1fi", and #6×fi" flathead woodscrews; #8×fi" panhead screws; ‹-20×1‹" flathead bolts, ‹" flat washers,and ‹" lock nuts (16 of each); #10-32×1"roundhead machine screws (6); ‹"hardboard and solid stock for the drawerfront drilling guide.Bits and blades: Stack dado set,¤" round-over router bit.
Buying GuideHardware. 4fl"-deep 22"-longdrawer side/slides no. 12K38.55,$8.20/pr. (3 pairs); card pulls no.01A57.65, $2.80 ea. (3); 4" lockingswivel casters no. 00K20.01, $11.50 ea.(4). Lee Valley Tools Ltd. Call 800/871-8158 or go to www.leevalley.com.
Materials List
Cutting Diagram
Cabinet LWT Qty*.Matl.FINISHED SIZE
EF G
H
I
K
H
J J J
KK
L
L
M
A B A BD
C
N N
‡ x 5fi x 96" Maple (4.0 bd. ft.)
‡ x 48 x 96" Medium-density fiberboard (MDF)
fi x 48 x 96" Medium-density overlay plywood (MDO)
E
A stiles ‡" 1fi" 23" M 4
B side rails ‡" 1fi" 23" M 4
C front rails ‡" 1‹" 18" M 2
D back rail ‡" 2" 17" M 1
E side panels fi" 22" 23" MDO 2
F bottom fi" 18" 21fi" MDO 1
G back fi" 18" 21‡" MDO 1
H top 1fi" 21fi" 25fi" LMDF 1
I mobile base ‡" 20" 24" MDF 1
Drawers
J drawer backs fi" 4‡" 15‡" MDO 3
K drawer bottoms fi" 15‡" 21¤" MDO 3
L small drawer fronts ‡" 6Í" 16‡" MDF 2
M large drawer front ‡" 8›" 16‡" MDF 1
N cleats fi" 2fi" 22" MDO 6
The purchase of these plans does nottransfer any copyright or other ownershipinterest in the plans, the design or thefinished project to the buyer. Buyer mayneither reproduce the plans for sale not offerfor sale any copies of the finished project.
md-00275 2/4/04 10:37 AM Page 8
Materials key: M–maple, MDO–medium-density overlay plywood, LMDF–laminated medium-density fiberboard, MDF–medium-density fiberboard.Supplies: #8ׇ", #8×1", #8×1‹", #8×1fi", and #6×fi" flathead wood screws; #8×fi" panhead screws; ‹-20×1‹" flathead bolts, ‹" flat washers, and ‹" lock nuts (16 of each); #10-32×1" roundhead machine screws (6); ‹" hardboard and solid stock for the drawer front drilling guide.Bits and blades: Stack dado set, ¤" round-over router bit.
Buying GuideHardware. 4fl"-deep 22"-long drawer side slides no. 12K38.55, (3 pairs); card pulls no. 01A57.65, (3); 4" locking swivel casters no. 00K20.01, (4). Lee Valley Tools Ltd. Call 800/871-8158 or go to www.leevalley.com.
Materials List
Cabinet LWT Qty*.Matl.FINISHED SIZE
A stiles ‡" 1fi" 23" M 4
B side rails ‡" 1fi" 23" M 4
C front rails ‡" 1‹" 18" M 2
D back rail ‡" 2" 17" M 1
E side panels fi" 22" 23" MDO 2
F bottom fi" 18" 21fi" MDO 1
G back fi" 18" 21‡" MDO 1
H top 1fi" 21fi" 25fi" LMDF 1
I mobile base ‡" 20" 24" MDF 1
Drawers
J drawer backs fi" 4‡" 15‡" MDO 3
K drawer bottoms fi" 15‡" 21¤" MDO 3
L small drawer fronts ‡" 6Í" 16‡" MDF 2
M large drawer front ‡" 8›" 16‡" MDF 1
N cleats fi" 2fi" 22" MDO 6
Browse more than 1,000 woodworking project plans, articles, tool reviews, books, techniques, & more. Each plan includes step-by-step instructions, professional color photography, and detailed illustrations.
WOODStore.net
Plans Techniques Articles Publications
Looking for information from Leading woodworking companies?
WOODWorkersCenter.com is just the site for your woodworking tool, accessory, and service informational needs. Use the online info request feature to request these companies latest catalogs or info.
WOODWorkersCenter.comWOODmagazine.com
a weaLth of information just a cLick away
The online presence of WOOD magazine, WOODmagazine.com speaks to online users of all woodworking skill levels with free woodworking plans, helpful forums, numerous articles, to help you become a better woodworker.
WOODmagazine.com/videosprofessionaL, portaBLe Video The biggest names in woodworking help you build your skills with downloadable videos.
By woodworkers, for woodworkers Watch free videos of other woodworkers showing their stuff.
watch a demo Before you Buy Don’t spend a penny on a tool or accessory until you learn how it works and what it can do.
free magaZine support 24/7 WOOD magazine editors provide more than 120 streaming videos, from 2 to 10 minutes in length.
More from WOOD Magazine
Top Related