SKFVibration Sensors
Vibration sensors•
Sensor selection, installation •and mounting overview
Cables and connectors•
Sensor housings•
Mounting accessories•
Power supply units•
CMSS 2100Standard Industrial Acceleration Sensor …
Typical Temperature Response
Temperature, °C (°F)
Dev
iatio
n, %
Sen
sitiv
ity
-20 0 +25 +50 +80 +120 (-4) (+32) (+77) (+122) (+176) (+248)
+20
+10
0
-10
-20
… Incorporating the latest in technology to meet demanding CE, EMC, and low noise level requirements.
Using detailed knowledge acquired from many years of supplying high quality sensors to a broad spectrum of industry users, SKF offers rugged accelerometers designed for the Pulp and Paper, Petrochemical, Steel, Mining and Construction, Metal Working, and Machine Tool Industries.
FeaturesFor use with the SKF Local Monitoring Unit (LMU’s) on-line •systems, protection systems and the ever versatile portable data collection Instruments.
Rugged, economical, and all around general purpose sensor.•
Sensitivity, 100 mV/g to optimize use in multiple applications.•
Exceptional bias voltage (BV) stability at elevated temperatures.•
Designed for exceptional low noise level for low frequencies at •elevated temperatures.
Meets stringent CE, EMC requirements.•
Smaller profile industrial accelerometers.•
Two (2) mounting studs (1/4–28 and M8 x 1.25) provided.•
Corrosion resistant and hermetically sealed for installation in high •humidity areas.
Reverse polarity wiring protection.•
Typical Frequency Response
0.5 10 100 1 k 20 kFrequency, Hz
Dev
iatio
n, d
B
10
3
2
1
0
-1
-2
-3
For additional information on SKF Reliability Systems products, contact:
SKF Reliability Systems5271 Viewridge Court • San Diego, California 92123 USATelephone: +1 858-496-3400 • FAX: +1 858-496-3531
Web Site: www.skf.com/cm® SKF is a registered trademark of the SKF Group.• All other trademarks are the property of their respective owners.•
© SKF Group 2008The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. SKF reserves the right to alter any part of this publication without prior notice.
SKF Patents include: #US04768380 • #US05679900 • #US05845230 • #US05854553 • #US05992237 •#US06006164 • #US06199422 • #US06202491 • #US06275781 • #US06489884 • #US06513386 • #US06633822 • #US6,789,025 • #US6,792,360 • US 5,633,811 • US 5,870,699 • #WO_03_048714A1
Publication CM2205 EN (Revised 4-08) • Printed in the United States of America
CMSS 2100Standard Industrial Acceleration Sensor
SpecificationsSpecifications conform to ISA-RP-37.2 (1-64) and are typical values referenced at +24 °C (+75 °F), 24 Vdc supply, 4 mA constant current and 100 Hz.
DYNAMICSensitivity: 100 mV/gSensitivity precision: ± 5% at +25 °C (+77 °F)Acceleration range: 80 g PeakAmplitude linearity: ≤ 1%, up to full scaleFrequency range:± 5%; 3.0 Hz to 5,000 Hz± 10%; 1.0 Hz to 9,000 Hz± 3 dB; 0.5 Hz to 14,000 HzResonance frequency: Mounted, nominal 30 kHzTransverse sensitivity: ≤ 5% of axial
ELECTRICALPower requirements:Voltage source: +24 Vdc nominal, +18 Vdc to +30 VdcConstant current diode: 2 to 10 mA dc, recommended 4 mAElectrical noise: 2.0 Hz; 20µg/√HzOutput impedance: < 100 OhmsVoltage bias: 12 VdcGrounding: Case isolated, internal shielding
ENVIRONMENTALTemperature range: -50 °C to +120 °C (-58 °F to +248 °F), operating temperatureVibration limits: 500 g peakShock limit: 5,000 g peakElectromagnetic sensitivity, equivalent g: 70 µg/GaussSealing: HermeticBase strain sensitivity: 200 µg/microstrainCE: According to the generic immunity standard for
Industrial Environment EN50082-2. Acceptance criteria: The generated “false equivalent
g level” under the above test conditions should be less than 2 milli g peak to peak.
PHYSICALDimensions: See drawingWeight: 90 gms (≈ 3.17 oz.)Case material: 316L stainless steel
Mounting: Internal 1/4–28 thread. Mounting studs provided. One (1) 1/4–28 to 1/4–28 english thread and one (1) M8 x 1.25 metric thread.Mounting torque: 2,9 N-m (24 in-lbs)Connector:Pin A: Signal/power (White wire)Pin B: Common (Black wire)Mating connector: CMSS 3106F-10SL-4S or equivalentRecommended cable: Two conductor shielded, teflon jacket, 100 pF/m (30 pF/ft)
Diagrams
Ordering informationCMSS 2100 General purpose industrial standard acceleration sensor with top exit C5015 two (2) pin connector.
1/4-28 and M8 mounting studs provided. Calibration sensitivity is provided on each accelerometer package with nominal sensitivity etched on each unit.
53.0 mm(2.10”) MODEL CMSS2100
S/N S00000
2-Pin connector
100 mV/g NOM
Made in the USA
A B
20.3 mm(0.80”)
22.3 mm(0.87”)
19.0 mm(0.75”)
Diameter1/4-28
Mounting hole
7/8”HEX
… Incorporating the latest in technology to meet the demanding CE, EMC and low level noise requirements.
Using detailed knowledge acquired from many years of supplying high quality sensors to a broad spectrum of industry users, SKF Condition Monitoring offers rugged accelerometers designed for the Pulp and Paper, Petrochemical, Steel, Mining and Construction, Metal Working, and Machine Tool Industries.
FeaturesFor use with the SKF Local Monitoring •Unit (LMU’s) on-line systems, protection systems and the ever versatile portable data collection Instruments.
Rugged, economical, and all around general •purpose sensor.
Sensitivity, 100 mV/g to optimize use in •multiple applications.
Exceptional bias voltage (BV) stability at •elevated temperatures.
Designed for exceptional low noise level for low frequencies at elevated temperatures.•
Meets stringent CE, EMC requirements.•
Low profile for side industrial accelerometer with captive mounting bolts (1/4–28, M6 x 1.00 or •M8 x 1.25) provided.
Corrosion resistant and hermetically sealed.•
Reverse polarity wiring protection.•
CMSS 2200/CMSS 2200-M8Low Profile Standard Acceleration Sensor …
Typical Temperature Response
Dev
iatio
n, %
Sen
sitiv
ity
Temperature, °C (°F)
-20 0 +25 +50 +80 +120 (-4) (+32) (+77) (+122) (+176) (+248)
+20
+10
0
-10
-20
Typical Frequency Response
0.7 10 100 1 k 10 kFrequency, Hz
Dev
iatio
n, d
B
3
2
1
0
-1
-2
-3
For additional information on SKF Reliability Systems products, contact:
SKF Reliability Systems5271 Viewridge Court • San Diego, California 92123 USATelephone: +1 858-496-3400 • FAX: +1 858-496-3531
Web Site: www.skf.com/cm® SKF is a registered trademark of the SKF Group.• All other trademarks are the property of their respective owners.•
© SKF Group 2008The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. SKF reserves the right to alter any part of this publication without prior notice.
SKF Patents include: #US04768380 • #US05679900 • #US05845230 • #US05854553 • #US05992237 •#US06006164 • #US06199422 • #US06202491 • #US06275781 • #US06489884 • #US06513386 • #US06633822 • #US6,789,025 • #US6,792,360 • US 5,633,811 • US 5,870,699 • #WO_03_048714A1
Publication CM2238 EN (Revised 4-08) • Printed in the United States of America
CMSS 2200/CMSS 2200-M8Low Profile Standard Acceleration Sensor
SpecificationsSpecifications conform to ISA-RP-37.2 (1-64) and are typical values referenced at +24 °C (+75 °F), 24 Vdc supply, 4 mA constant current and 100 Hz.
DYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10% at +25 °C (+77 °F)Acceleration range: 80 g peakAmplitude linearity: 1%Frequency range:± 10%; 1.0 Hz to 5,000 Hz± 3 dB; 0.7 Hz to 10,000 HzResonance frequency: Mounted, minimum 22 kHzTransverse densitivity: ≤ 5% of axial
ELECTRICALPower requirements:Voltage source: +18 Vdc to +30 VdcConstant current diode: 2 to 10 mA dc, recommended 4 mAElectrical noise: 2.0 Hz; 20 µg/√HzOutput impedance: < 100 OhmsVoltage bias: 12 VdcGrounding: Case isolated, internal shielding
ENVIRONMENTALTemperature range: -50 °C to +120 °C (-58 °F to +248 °F) operating temperatureVibration limits: 500 g peakShock limit: 5,000 g peakElectromagnetic sensitivity, equivalent g: 70 µg/GaussSealing: HermeticBase strain sensitivity: 200 µg/microstrainCE: According to the Generic immunity standard for
Industrial Environment EN50082-2. Acceptance criteria: The generated “false equivalent g
level” under the above test conditions should be less than 2 milli g peak to peak.
PHYSICALDimensions: See drawingWeight: 145 gms (≈ 5.10 oz.)Case material: 316L stainless steelMounting: Captive mounting bolts provided. One (1) 1/4–28 english thread and one (1) M6 x 1.00 metric thread.Mounting torque: 30 in-lbs, 3,4 N-m
Ordering informationCMSS 2200 • Low Profile Acceleration Sensor with side exit C5015 two (2) pin connector.
1/4-28 and M6 mounting studs provided. Calibration sensitivity is provided on each accelerometer package with nominal sensitivity etched on each unit.
CMSS 2200-M8 • Low Profile Acceleration Sensor with side exit C5015 two (2) pin connector.
M8 mounting stud provided. Calibration sensitivity is provided on each accelerometer package with nominal sensitivity etched on each unit.
Connector:Pin A: Signal/power (White wire)Pin B: Common (Black wire)Mating connector: CMSS 3106F-10SL-4S or equivalentRecommended cable: Two conductor shielded, teflon jacket, 100 pF/m (30 pF/ft)
Diagrams
A B
+ -
MODEL CMSS2200S/N S0000
25.0 mm(1.00”)
38.0 mm(1.50”) 26.0 mm
(1.04”)
2-PinConnectorMIL-C-5015
37.0 mm(1.44”)
53.0 mm(2.10”)
5/32” Allen Head
CMSS 2200:1/4-28 MountingthreadCMSS 2200-M8:M8 Mounting thread
… Incorporating the latest in technology to meet the demanding and stringent elevated temperature requirements such as those associated with tropic and desert installations, steel mills, and pulp and paper applications.
Using detailed knowledge acquired from many years of supplying high quality sensors to a broad spectrum of industry users, SKF Reliability Systems offers rugged high temperature accelerometers designed for machines of the Pulp and Paper, Petrochemical, Steel, Mining and Construction, Metal Working, and Machine Tool Industries.
FeaturesFor use with the SKF Local Monitoring Unit (LMU’s) On-line Systems, •Protection Systems and the ever versatile Portable Data Collection Instruments.
Rugged, economical, and all around high temperature general purpose •sensor for up to +150 °C (+302° F) operating temperature.
Sensitivity, 100 mV/g to optimize use in multiple applications.•
Exceptional bias voltage (BV) stability at elevated temperatures.•
Designed for exceptional low noise level for low frequencies at elevated •temperatures.
Meets stringent CE, EMC requirements.•
Two (2) mounting studs (1/4–28 and M8 x 1.25) provided.•
Corrosion resistant and hermetically sealed for installation in high •humidity areas.
Reverse polarity wiring protection.•
CMSS 2106High Temperature Industrial Acceleration Sensor …
Typical Temperature Response
Dev
iatio
n, %
Sen
sitiv
ity +20
+10
0
-10
-20
Temperature, °C (°F)
-50 -25 0 +25 +50 +75 +100 +125 +150 (-58) (+13) (+32) (+77) (+122) (+167) (+212) (+258) (+302)
Typical Frequency Response
1 10 100 1 k 10 k 13 kFrequency, Hz
Dev
iatio
n, d
B
3
2
1
0
-1
-2
-3
For additional information on SKF Reliability Systems products, contact:
SKF Reliability Systems5271 Viewridge Court • San Diego, California 92123 USATelephone: +1 858-496-3400 • FAX: +1 858-496-3531
Web Site: www.skf.com/cm® SKF is a registered trademark of the SKF Group.• All other trademarks are the property of their respective owners.•
© SKF Group 2008The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. SKF reserves the right to alter any part of this publication without prior notice.
SKF Patents include: #US04768380 • #US05679900 • #US05845230 • #US05854553 • #US05992237 •#US06006164 • #US06199422 • #US06202491 • #US06275781 • #US06489884 • #US06513386 • #US06633822 • #US6,789,025 • #US6,792,360 • US 5,633,811 • US 5,870,699 • #WO_03_048714A1
Publication CM2236 EN (Revised 4-08) • Printed in the United States of America
CMSS 2106High Temperature Industrial Acceleration Sensor
SpecificationsSpecifications conform to ISA-RP-37.2 (1-64) and are typical values referenced at +24 °C (+75 °F), 24 Vdc supply, 4 mA constant current and 100 Hz.
DYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10% at -50 °C to +150 °C (-58 °F to +302 °F)Acceleration range: 50 g peakAmplitude linearity: 1%Frequency range:± 5%; 4.0 Hz to 4,000 Hz± 10%; 3.0 Hz to 6,000 Hz± 3 dB; 1.0 Hz to 10,000 HzResonance frequency: Mounted, nominal 20 kHzTransverse sensitivity: ≤ 5% of axial
ELECTRICALPower requirements:Voltage source: +24 Vdc nominal, +18 Vdc to +30 VdcConstant current diode: 2 to 4 mA dc, recommended 4 mAElectrical noise: 2.0 Hz; 30µg/√HzOutput impedance: < 100 OhmsVoltage bias: 12 Vdc at +25 °C (+77 °F); 11 Vdc at +150 °C (+302 °F)Grounding: Case isolated, internal shielding
ENVIRONMENTALTemperature range: -50 °C to +150 °C (-58 °F to +302 °F) operating temperatureVibration limits: 500 g peakShock limit: 2,500 g peakElectromagnetic sensitivity, equivalent g: 15 µg/GaussSealing: HermeticBase strain sensitivity: 500 µg/microstrainCE: According to the Generic immunity standard for
Industrial Environment EN50082-2. Acceptance Criteria: The generated “false equivalent
g level” under the above test conditions should be less than 2 milli g peak to peak.
PHYSICALDimensions: See drawingWeight: 135 gms (≈ 4.73 oz.)
Case material: 316L stainless steelMounting: Internal 1/4–28 thread. Mounting studs provided. One (1) 1/4–28 to 1/4–28 english thread and one (1) M8 x 1.25 metric thread.Mounting torque: 2,9 N-m (24 in-lbs)Connector:Pin A: Signal/power (White wire)Pin B: Common (Black wire)Mating connector: CMSS-3106F-10SL-4S or equivalentRecommended cable: Two conductor shielded, teflon jacket, 30 pF/ft (100 pF/m)
Diagrams
A B
61.0 mm(2.42”)
MODELCMSS2106
S/N S00000
2-Pin connector
100 mV/gNOM
23.8 mm(0.94”)
Diameter1/4-28
Mounting hole
15/16”HEX
45.0 mm(1.78”)
25.0 mm(1.00”)
Diameter
Made in theUSA
Ordering informationCMSS 2106 High Temperature Industrial Standard Acceleration Sensor with top exit C5015 two (2) pin connector.
1/4-28 and M8 mounting studs provided. Calibration sensitivity is provided on each accelerometer package with nominal sensitivity etched on each unit.
… Incorporating the latest in technology to meet the demanding and stringent elevated temperature requirements such as those associated with tropic and desert installations, steel mills and pulp and paper applications.
Using detailed knowledge acquired from many years of supplying high quality sensors to a broad spectrum of industry users, SKF Condition Monitoring offers rugged high temperature accelerometers designed for the Pulp and Paper, Petrochemical, Steel, Mining and Construction, Metal Working, and Machine Tool Industries.
FeaturesFor use with the SKF Local Monitoring Unit •(LMU’s) On-Line Systems and Protection Systems.
Rugged, economical, and all around high •temperature general purpose sensor for up to +150 °C (+302 °F) operating temperature.
Sensitivity, 100 mV/g to optimize use in •multiple applications.
Exceptional bias voltage (BV) stability at •elevated temperatures.
Designed for exceptional low noise level for low •frequencies at elevated temperatures.
Meets stringent CE, EMC requirements.•
Low profile, side exit, high temperature industrial accelerometer.•
Corrosion resistant and hermetically sealed for installation in high humidity areas.•
Reverse polarity wiring protection.•
CMSS 2207High Temperature Low Profile Acceleration Sensor …
Typical Temperature Response
Dev
iatio
n, %
Sen
sitiv
ity
Temperature, °C (°F)
0 +25 +50 +75 +100 +120 (+32) (+77) (+122) (+167) (+212) (+248)
+20
+10
0
-10
-20
Typical Frequency Response
0.7 10 100 1 k 10 kFrequency, Hz
Dev
iatio
n, d
B
3
2
1
0
-1
-2
-3
For additional information on SKF Reliability Systems products, contact:
SKF Reliability Systems5271 Viewridge Court • San Diego, California 92123 USATelephone: +1 858-496-3400 • FAX: +1 858-496-3531
Web Site: www.skf.com/cm® SKF is a registered trademark of the SKF Group.• All other trademarks are the property of their respective owners.•
© SKF Group 2008The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. SKF reserves the right to alter any part of this publication without prior notice.
SKF Patents include: #US04768380 • #US05679900 • #US05845230 • #US05854553 • #US05992237 •#US06006164 • #US06199422 • #US06202491 • #US06275781 • #US06489884 • #US06513386 • #US06633822 • #US6,789,025 • #US6,792,360 • US 5,633,811 • US 5,870,699 • #WO_03_048714A1
Publication CM2272 EN (Revised 4-08) • Printed in the United States of America
CMSS 2207High Temperature Low Profile Acceleration Sensor
SpecificationsSpecifications conform to ISA-RP-37.2 (1-64) and are typical values referenced at +24 °C (+75 °F), 24 Vdc supply, 4 mA constant current and 100 Hz.
DYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10% at +25 °C (+77 °F)Acceleration range: 50 g peakAmplitude linearity: ≤ 1% up to full scaleFrequency range:± 5%; 4.0 Hz to 5,000 Hz± 10%; 3.0 Hz to 7,000 Hz± 3 dB 1.0 Hz to 11,000 HzResonance frequency: 20 kHzTransverse sensitivity: ≤ 5% of axial
ELECTRICALPower requirements:Voltage source: +24 Vdc nominal, +18 Vdc to +30 VdcConstant current diode: 2 to 4 mA dc, recommend 4 mAElectrical noise: 2.0 Hz; 30µg/√HzOutput impedance: < 100 OhmsVoltage bias: 12 Vdc at +25 °C (+77 °F); 11 Vdc at +150 °C (+302 °F)Grounding: Case isolated, internal
ENVIRONMENTALTemperature range: -50 °C to +150 °C (-58 °F to +302 °F) operating temperatureVibration limits: 500 g peakShock limit: 2,500 g peakElectromagnetic sensitivity, equivalent g: < 5 µg/GaussBase strain sensitivity: 100 µg/microstrainCE: According to the Generic immunity standard for
Industrial Environment EN50082-2. Acceptance criteria: The generated “false equivalent
g level” under the above test conditions should be less than 2 milli g peak to peak.
PHYSICALDimensions: See drawingWeight: 145 gms (≈ 5.10 oz.)Case material: 316L stainless steelMounting: Captive mounting bolts provided. One (1) each 1/4–28 english thread and one (1) M6 x 1.00 metric thread.Mounting torque: 3,4 N-m (30 in-lbs)
Ordering informationCMSS 2207 • Low Profile High Temperature Acceleration Sensor with side exit C5015 two (2) pin connector.
1/4-28 and M6 mounting studs provided. Calibration sensitivity is provided on each accelerometer package with nominal sensitivity etched on each unit.
Connector:Pin A: Signal/power (White wire)Pin B: Common (Black wire)Mating connector: CMSS 3106F-10SL-4S or equivalentRecommended cable: Two conductor shielded, teflon jacket, 100 pF/m (30 pF/ft)
Diagrams
Side View
A B
End View
Top View
Bottom View
100
mV/
g N
OM
Mad
e in
the
USA
30.0 mm(1.20”)
1/4-28Mounting
Thread
2-PinConnectorMIL-C-5015
Safety Wire Hole1.5 mm (0.062”)Diameter
43.0 mm(1.70”)
6.0 mm(0.25”)
26.0 mm(1.05”)
Diameter
54.0 mm (2.15”)
CMSS 2110-3Industrial acceleration sensor with integral 5 meter (16.5 feet) rugged stainless steel braided cable …
… Incorporating the latest in technology to meet demanding CE, EMC and low noise level requirements.
FeaturesDesigned for use with the SKF Machine •Condition Transmitters (MCT)
Economical, rugged, general purpose•
Sensitivity, 30 mV/g to optimize use in most •applications
Designed to meet stringent CE, EMC •requirements
Cable shield and braid connected to sensor •housing for better noise rejection
Corrosion resistant•
Miswiring protection•
SpecificationsDYNAMICSensitivity: 30 mV/g at +20 °C (+68 °F)Sensitivity precision: ± 10% at +20 °C (+68 °F)Sensitivity deviation over full temperature range: < ± 10% of the sensitivity at +20 °C (+68 °F)Amplitude linearity: < 1% up to full scaleTransverse sensitivity: < 5% of axialFrequency range:3.0 Hz – 8.0 kHz, ± 10% at +20 °C (+68 °F)0.8 Hz – 10.0 kHz, ± 3 dB at +20 °C (+68 °F)Sensor resonance frequency: Nominal 20 kHz or higher. Controlled resonance amplitude. Second order Q limiting filter.Acceleration output range: Minimum ± 6 V equivalent to 200 g peak. Turn on time for one (1) time constant is 0.5 seconds.
ELECTRICALPower Requirements:Voltage Source: +24 Vdc, ± 20%Constant Current Diode: 2 – 6 mA dcElectrical noise: Broadband (2 Hz to 20 kHz) < 0.7 milli g RMSOutput impedance: < 50 Ohms
Typical Temperature Response
Dev
iatio
n, %
Sen
sitiv
ity
+10
+5
0
-5
-10
Temperature, °C (°F)
-50 -25 0 +25 +50 +75 +100 +120 (-58) (+13) (+32) (+77) (+122) (+167) (+212) (+248)
Frequency, Hz
Typical Frequency Response
Ampl
itude
(dB
)
+20
+10
0
-10
-200.8 100 1k 30k 40k10k 20k
Standard Armored Cable
1/4 – 28"
Bend Radius19.0 mm (0.75”)
CMSS 2110/3S/N 98765
22.0 mm(0.87”)
25.0 mm(1.00”)
45.0 mm(1.75”)
51.0 mm(2.00”)
25.0 mm(1.00”) Hex
For additional information on SKF Reliability Systems products, contact:
SKF Reliability Systems5271 Viewridge Court • San Diego, California 92123 USATelephone: +1 858-496-3400 • FAX: +1 858-496-3531
Web Site: www.skf.com/cm® SKF is a registered trademark of the SKF Group.• All other trademarks are the property of their respective owners.•
© SKF Group 2008The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. SKF reserves the right to alter any part of this publication without prior notice.
SKF Patents include: #US04768380 • #US05679900 • #US05845230 • #US05854553 • #US05992237 •#US06006164 • #US06199422 • #US06202491 • #US06275781 • #US06489884 • #US06513386 • #US06633822 • #US6,789,025 • #US6,792,360 • US 5,633,811 • US 5,870,699 • #WO_03_048714A1
Publication CM2204 EN (Revised 4-08) • Printed in the United States of America
CMSS 2110-3Industrial acceleration sensor with integral 5 meter (16.5 feet) rugged stainless steel braided cable
SpecificationsELECTRICAL (continued)
Grounding: Case isolated, internal shielding (Faraday cage). The internal Faraday cage is connected to the signal return of the shielded twisted pair. The internal shield as well as the stainless steel braid is connected to the sensor housing.Isolation to sensor housing: > 10 Mega Ohms over full temperature range.V bias: 11.5 Vdc (± 10%) for 24 Vdc supply voltage over the temperature range from -50 °C to +100 °C (-58 °F to +212 °F).Over voltage protectionReverse polarity (wiring) protection
ENVIRONMENTALTemperature range: -50 °C to +120 °C (-58 °F to +248 °F) operating temperature.Vibration limits: 500 g peakShock limit: 1,000 g peakElectromagnetic sensitivity, equivalent g: < 100 µg/Gauss at 50 to 60 HzBase strain sensitivity: 200 µg/micro strainCE: According to the Generic immunity standard for
Industrial Environment EN50082-2. Acceptance criteria: The generated “false equivalent
g level” under the above test conditions should be less than 2 milli g peak to peak.
PHYSICALDimensions: See drawing. Integral cable with shielded twisted pair, and stainless steel braid. Cable length is 5 meters (16.5 feet) long.Weight: 350 g (12.25 oz.), including 5 meters (16.5 feet) of cableCase material: 316L stainless steelMounting: 1/4–28 to M8 and 1/4–28 to 1/4–28 mounting studs provided.Cable: Integral cable, 5 meters (16.5 feet) long. Shielded twisted pair; 2 times AWG 20. Shield grounded to sensor housing. Cable armored with stainless steel braid. Braid also connected to sensor housing. High temperature cable. Cable diameter less than 5 mm.Cable specifications: 2/C 20 AWG FEP/A/M/FEP 10-1254.Cable capacitance: 80 pF/m (25 pF/ft).Cable connectors: Integral cable;Power/signal: WhiteCommon: BlackShielding: Drain wire
Diagrams
Ordering informationCMSS 2110-3 General purpose industrial acceleration sensor with 5 meter (16.5 feet) stainless steel over-braided twisted pair cable.
CMSS 2110Industrial Acceleration Sensor with integral 5 meter (16.5 feet) over-braided cable …
SpecificationsSpecifications conform to ISA-RP-37.2 (1-64) and are typical values referenced at +24 °C (+75 °F), 24 Vdc supply, 4 mA constant current and 100 Hz.
DYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10%Sensitivity deviation over full temperature range: ≤ ± 10%Amplitude linearity: ≤ 1% up to full scaleTransverse sensitivity: ≤ 5% of axialFrequency range: 0.8 Hz to 10.0 kHz, ± 3 dBSensor resonance frequency: Nominal 25 kHz or higher. Controlled resonance amplitude. +15 dB maximum at resonance.Acceleration output range: Minimum ± 8 V equivalent to 80 g peak. Turn on time to within 10% of final bias is ≤ 1.0 seconds.
Using detailed knowledge acquired from many years of supplying high quality sensors to a broad spectrum of industry users, SKF Reliability Systems introduces this new series of rugged accelerometers designed for installation where cable protection is paramount without the luxury of cable trays or protective conduit.
FeaturesRecommended for use •with the SKF Machine Condition Transmitters (MCT)
Economical, rugged, •general purpose
Sensitivity, 100 mV/g •to optimize use in most applications
Designed to meet stringent CE, EMC •requirements
Cable shield and braid connected to sensor •housing for better noise rejection
Corrosion resistant•
Miswiring protection•
… Incorporating the latest in technology to meet demanding CE, EMC and low noise level requirements.
Machine Condition Transmitters (MCT)
Temperature, °C (°F)
Typical Temperature Response
Dev
iatio
n, %
Sen
sitiv
ity
+10
+5
0
-5
-10 -50 -25 0 +25 +50 +75 +100 +120 (-58) (+13) (+32) (+77) (+122) (+167) (+212) (+248)
0.8 100 1k 30k 40kFrequency, Hz
Typical Frequency Response
Ampl
itude
(dB
)
+20
+10
0
-10
-2010k 20k
For additional information on SKF Reliability Systems products, contact:
SKF Reliability Systems5271 Viewridge Court • San Diego, California 92123 USATelephone: +1 858-496-3400 • FAX: +1 858-496-3531
Web Site: www.skf.com/cm® SKF is a registered trademark of the SKF Group.• All other trademarks are the property of their respective owners.•
© SKF Group 2008The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. SKF reserves the right to alter any part of this publication without prior notice.
SKF Patents include: #US04768380 • #US05679900 • #US05845230 • #US05854553 • #US05992237 •#US06006164 • #US06199422 • #US06202491 • #US06275781 • #US06489884 • #US06513386 • #US06633822 • #US6,789,025 • #US6,792,360 • US 5,633,811 • US 5,870,699 • #WO_03_048714A1
Publication CM2237 EN (Revised 4-08) • Printed in the United States of America
CMSS 2110Industrial acceleration sensor with integral 5 meter (16.5 feet) over-braided cable
Specifications (continued)
ELECTRICALPower requirements:Voltage source: +24 Vdc nominal, ± 20%Constant current diode: 2 to 10 mA dc, recommend 4 mAElectrical noise: Broadband (2.5 Hz to 25.0 kHz) < 0.6 milli g RMSOutput impedance: < 50 OhmsGrounding: Case isolated, internal shielding (Faraday cage). The internal Faraday cage is connected to the signal return of the shielded twisted pair. The internal shield as well as the stainless steel braid is connected to the sensor housing.Isolation to sensor housing: > 10 MOhms over full temperature rangeV bias:12.5 Vdc to 13.5 Vdc for +24 Vdc supply over temperature range -50 °C to +99 °C (-58 °F to +211 °F)11.0 Vdc to 14.0 Vdc for +24 Vdc supply over temperature range +100 °C to +120 °C (+212 °F to +248 °F)Over voltage protectionReverse polarity (wiring) protection
ENVIRONMENTALTemperature range: -50 °C to +120 °C (-58 °F to +248 °F) operating temperatureVibration limits: 500 g peakShock limit: 1,000 g peakElectromagnetic sensitivity, equivalent g: < 100 µg/Gauss at 50 to 60 HzBase strain sensitivity: 200 µg/micro strainCE: According to the Generic immunity standard for
Industrial Environment EN50082-2. Acceptance criteria: The generated “false equivalent
g level” under the above test conditions should be less than 2 milli g peak to peak.
PHYSICALDimensions: See drawing. Integral cable with shielded twisted pair, and stainless steel braid. Cable length is 5 meters (16 feet) long.Weight: 350 gms (≈ 12.25 oz.) including 5 meters (16.5 feet) of cable.
Case material: 316L stainless steelMounting: Internal 1/4–28 thread. Mounting studs provided. One (1) 1/4–28 to 1/4–28 English thread and one (1) M8 x 1.25 Metric thread.Mounting torque: 2.9 N-m (24 in-pounds)Cable: Integral cable 5 meters (16 feet) long. Shielded twisted pair; 2 times AWG 20. Shield grounded to sensor housing. Cable armored with stainless steel braid. Braid also connected to sensor housing. High temperature cable. Cable diameter less than 5 mm (0.19”).Cable specifications: 2/C 20 AWG FEP/A/M/FEP 10-1254. Recommend two (2) wire, twisted, shielded.Connector: Power signal: White wire Common: Black wire Shielding: Drain wire
Diagrams
Ordering InformationCMSS 2110 General Purpose Industrial Standard Acceleration Sensor with integral 5 meter (16.5 feet) stainless steel over-braided twisted pair cable.
1/4-28 and M8 mounting studs provided. Calibration sensitivity is provided on each accelerometer package with nominal sensitivity etched on each unit.
Standard Armored Cable
1/4-28"
Bend Radius19.0 mm (0.75”)
CMSS 2110S/N 98765
22.0 mm(0.87”)
25.0 mm(1.00”)
45.0 mm(1.75”)
51.0 mm(2.00”)
25.0 mm(1.00”) Hex
CMSS MT1Low Profile Machine Tool Accelerometer
The CMSS MT1 Machine Tool accelerometer features a low profile, bolt mounted sensor with a double-shielded integral cable. This sensor is optimized for use with on-line monitoring systems in Machine Tool applications.
FeaturesFor use with the SKF On-line surveillance •systems.
Meets CE, EMC requirements.•
High resistance to electrical •noise.
Low profile side exit industrial •accelerometer with captive bolt (M8 x 1.25, 33 mm length) provided.
Compact design ideal for •mounting with limited space.
Corrosion resistant and •hermetically sealed.
+8+6+4
dB +20
-2-4
0.1 1 10 100 1 k 10 k 12 k Hz
Typical Frequency Response
For additional information on SKF Reliability Systems products, contact:
SKF Reliability Systems5271 Viewridge Court • San Diego, California 92123 USATelephone: +1 858-496-3400 • FAX: +1 858-496-3531
Web Site: www.skf.com/cm® SKF is a registered trademark of the SKF Group.• All other trademarks are the property of their respective owners.•
© SKF Group 2008The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. SKF reserves the right to alter any part of this publication without prior notice.
SKF Patents include: #US04768380 • #US05679900 • #US05845230 • #US05854553 • #US05992237 •#US06006164 • #US06199422 • #US06202491 • #US06275781 • #US06489884 • #US06513386 • #US06633822 • #US6,789,025 • #US6,792,360 • US 5,633,811 • US 5,870,699 • #WO_03_048714A1
Publication CM2296 EN (4-08) • Printed in the United States of America
SpecificationsDYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10% at +25 °C (+77 °F)Acceleration range: 50 g peakAmplitude linearity: 1% of full scaleFrequency range: ± 3 dB; 0.32 Hz to 10,000 HzResonance frequency: 10 kHz (mounted)Transverse sensitivity: ≤ 5% of axial
ELECTRICALPower requirements:Voltage source: +18 Vdc to +28 VdcConstant current diode: 2 to 10 mA DC, recommended 4 mAElectrical noise: < 100 µV from 2.5 Hz to 25 kHzOutput impedance: < 100 OhmsOutput bias voltage: 8 Vdc to 12 VdcGrounding: Case connected to outer shield, inner shield open
ENVIRONMENTALTemperature range:Operating: -40 °C to +85 °C (-40 °F to +185 °F)Storage: -54 °C to +121 °C (-65 °F to +250 °F)Shock limit: 7,000 g peakSealing: EncapsulatedCE: According to the immunity standard for Industrial Environment EN50082-2, Heavy Industrial
PHYSICALDimensions: See drawingWeight: Shipping weight. See table under Ordering Information.Case material: 304 stainless steelMounting: Captive mounting bolts provided: one (1) M8 x 1.25 Metric thread, 33 mm length.Mounting torque: 4,5 N-m (40 in-lbs)Cable termination:Signal/power: White wireCommon: Black wireInner Shield: Drain wireOuter Shield: Braid
Ordering informationCMSS MT1 General purpose low profile Machine Tool industry accelerometers
Part Number Cable Length Weight
CMSS MT1-16 4.88 meters(16 feet)
256 grams(9 ounces)
CMSS MT1-32 9.75 meters(32 feet)
482 grams(17 ounces)
CMSS MT1-64 19.51 meters(64 feet)
964 grams(34 ounces)
CMSS MT1Low Profile Machine Tool Accelerometer
35.95 mm(1.415”)
21.45 mm(0.844”)
8.50 mm(0.335”)17.00 mm
(0.669”)
Ø 8.50 mm(0.335”)
Dimension “A”(Total length)
Double shielded, twisted pair
Outside diameter of cable, approximately 3.6 mm
27.00 mm(1.063”) 19.00 mm
(0.748”)
0.75 mm(0.029”)
12.25 mm(0.482”)
M8 x 1.25 Socket cap head screw (33 mm long)
Drain (open)White (sensor – signal and power)Black (sensor – return)Screen (external shield connected to case)CMSS MT1
S/N 99999
Diagrams
CMSS MT3Special Purpose, Adhesive Mount Accelerometer
ApplicationsMachine Tool Spindles (Adhesive mounting in pre-machined hole)•
General FunctionalityThe CMSS MT3 Machine Tool accelerometer consists of an acceleration sensor with double-shielded integral cable designed for epoxy mounting. This sensor is a custom product designed for machine tool spindle applications (not for general use).
+8+6+4
dB +20
-2-4
0.1 1 10 100 1 k 10 k 12 k Hz
Typical Frequency Response
For additional information on SKF Reliability Systems products, contact:
SKF Reliability Systems5271 Viewridge Court • San Diego, California 92123 USATelephone: +1 858-496-3400 • FAX: +1 858-496-3531
Web Site: www.skf.com/cm® SKF is a registered trademark of the SKF Group.• All other trademarks are the property of their respective owners.•
© SKF Group 2008The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. SKF reserves the right to alter any part of this publication without prior notice.
SKF Patents include: #US04768380 • #US05679900 • #US05845230 • #US05854553 • #US05992237 •#US06006164 • #US06199422 • #US06202491 • #US06275781 • #US06489884 • #US06513386 • #US06633822 • #US6,789,025 • #US6,792,360 • US 5,633,811 • US 5,870,699 • #WO_03_048714A1
Publication CM2297 EN (4-08) • Printed in the United States of America
CMSS MT3Special Purpose, Adhesive Mount Accelerometer
SpecificationsDYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10% at +25 °C (+77 °F)Amplitude linearity: 1% of full scaleFrequency range: ± 3 dB; 0.32 Hz to 10,000 HzResonance frequency: ≥ 10 kHz (mounted)Transverse sensitivity: < 9% of axial
ELECTRICALPower requirements:Voltage source: +18 Vdc to +28 VdcConstant current diode: 2 to 10 mA DC, recommended 4 mAElectrical noise: < 100 µV from 2.5 Hz to 25 kHzOutput impedance: < 100 OhmsOutput bias voltage: 8 Vdc to 12 VdcGrounding: Case connected to outer shield, inner shield open
ENVIRONMENTALTemperature range:Operating: -40 °C to +85 °C (-40 °F to +185 °F)Storage: -50 °C to +120 °C (-58 °F to +248 °F)
Acceleration range: 50 g peakShock limit: 7,000 g peakSealing: EncapsulatedCE: According to the immunity standard for Industrial Environment EN50082-2, Heavy Industrial
PHYSICALDimensions: The sensor case dimensions are 18.29 mm (round) x 22.00 mm (height). Refer to drawing for details.Weight: 185 gramsCore material: 316L stainless steelMounting: Glued on to machine in pre-machined hole
Ordering informationCMSS MT3-08 Special purpose, adhesive mount, Machine Tool industry accelerometer with 2.5 meter (8 feet) integral cable.
2500 mm (98.43") total length
Outside diameter of cableapproximately 3.6 mm (0.142")
Double-shielded, twisted pair
16.00 mm(0.630")
18.29 mm (ø 0.720")
18.50 mm(0.728")
Drain (Open)Sensor (–) Black WireSensor (+) White Wire
Screen(Connected to Casing)
22.00 mm(0.866")
Diagrams
Top Related