Vendo HVV 721/8 2006
Pa
trofitting Guide
/821 Retrofit Kit a Vendo Vending Machiner installing and configuring the JCM-10 Bill Recycler and A-66 Coin nding Machine. The Vendo HVV 721/
components and support guides:
& CC RETROFIT COMPONENTS parts in a Vendo HVV 721/821 Retrofit Kit.
k
– 1 - Hole Gasket (Part No: 900-100228R) – 5 - 4 inch Plastic Cable Ties (450-200049R) – 1 - Retrofit Guide (Part No: 960-100138R).
Tool Requirements• 1- Power Drill & a 5/32” Twist Drill Bit• 1 - #2 Phillips Screwdriver• 1 - 11/32" Deep Well Nut Drive• 1 - 7/16" Deep Well Nut Drive• 1 - Pair Wire Cutters
. 2 or greater). 3 or greater). 3 or greater)0114 Rev. A or greater)
PERSONAL NWrite any pertihere. rofitting Guide
21 Retrofit Kit Retrofitting Guide July, 2006 July,
Re
Vendo HVV 721Optipay™ BV/RC/CC into
This document contains information foOptipay™ DBV-301 Bill Validator, RCChanger into a Vendo HVV 721/821Ve821 Retrofit Kit includes the following
PRIMARY JCM OPTIPAY™ BV, RCFigure 1 illustrates the primary component
• 1- Vendo Installation Kit (JCM Part No: 701-000165R) containing:
– 1 - DBV-301 Vendo HVV MDB Extension Harness (Part No: 400-100227R)
– 1 - DBV-301 Vendo HVV Switch ExtensionHarness (Part No: 400-100228R)
– 6 - DBV-301 Vendo HVV Circuit Board LocStandoffs (Part No: 900-100184R)
– 1 - Vendo HVV Bracket (Part No: 200-100290R)
– 4 - #8-32 Kep-lock Nuts (Part No. 140-020832R)
Optipay™ CC Installation Guide (JCM Part No. 960-000105 RevOptipay™ BV Installation Guide (JCM Part No. 960-000106 RevOptipay™ RC Installation Guide (JCM Part No. 960-000107 RevOptipay™ System Interconnection Guide (JCM Part No. 960-00
OTES AND COMMENT AREAnent notes or comments regarding your particular installation Ret
o. 960-100138R_Rev. A © 2006, JCM American, Corporation1
A-66
5” Plastic Cable Ties
Vendo HVV MDB Extension Harness
Circuit Board Lock Standoffs
Vendo HVV Switch Harness
Kep-Lock Nuts
Hole Gasket
RC-10
-30X Vendo HVV Bracket
Kit #701-000165R ContentsJCM RC-10/DBV-301/A66 Combination
Figure 1 Primary Vendo HVV 721/821 Retrofit Kit Component Parts
© 2006, JCM American, Corporation Part N1 2rt No. 960-100138R_Rev. A
925 Pilot Road, Las Vegas, Nevada 89119Office & Technical Support: (800) 683-7248 (option 5 after hours), FAX: (702) 651-0214
E-mail: [email protected] http://www.jcm-american.com
JCM is a registered trademark of JCM American Corporation. All other product namesmentioned herein may be registered trademarks or trademarks of their respective companies.Furthermore, ™, ® and © are not always mentioned in each case throughout this publication.
DBV
V ting Guide July, 2006
P © 2006, JCM American, Corporation11
OUH
Install Six Plastic Standoffs in Control
able ties, secure the interconnecting RC, BV or one another where appropriate.r with the correct denominations of coins
9.Press the Plus Keypad Button the Coin Changer twice (2 times) to reset the coin counters (See Figure 32).10.Insert a variety of bills and coins into the Optipay™ BV and CC to determine if the entire JCM Optipay™ Payment System is operating properly.
AL CHECKined in the respective Optipay™ product
ry, refer to the related primary service of this system interconnection, or call r additional instruction.
If additional information for interconnecting an Optipay™ DBV-301, RC-10 or ay™ System Interconnection Guide (Part ystem integration.
Figure 32 Optipay™ CC Keypad
PlusKey
+
art No. 960-100138R_Rev. A 2
Figure 5 Installing Standoffs
Board Bracket
Figure 4 Removing Control Board Plugs and Ground Wire
Remove the SevenCircuit BoardConnectors andGround Wire
Note WireColor Order& Locations
A-66 unit is required, refer to the OptipNo. 960-000114R) to ensure a proper s
endo HVV 721/821 Retrofit Kit Retrofitting Guide Retrofit
PTIPAY™ BV/RC INSTALLATION STEPSse the following steps to install a combined RC-10/DBV-301 unit into a Vendo VV Vending Machine:
1. Remove power to the Vending Machine and remove the existing equipment.2. Remove the four (4) 7/16 inch nuts and carriage bolts securing the Upper Bracket
(See Figure 2).3. Remove the four (4) 7/16 inch nuts and carriage bolts securing left and right
Harness Cover (See Figure 3).
4. Unplug the seven (7) Control Board Connectors, remove the Ground Wire from the frame and retain the grounding screw. Note the key positions of each connec-tor (See Figure 4).
5. Install the six (6) kit supplied standoffs into the new Control Board Bracket (See Figure 5).
Figure 3 Removing the Harness Cover Mounting Nuts & Bolts
Remove the 47/16” Harness
Nuts and BoltsCover Mounting
Figure 2 Removing the Top Bracket
Remove the TopFour 7/16” BracketMounting Nuts & Bolts
7. Using the remaining 4 inch plastic cand CC wire harnesses to the frame
8. Fill the Optipay™ CC Coin Change(See Figure 31).
OPERATIONAL CHECKS
RETROFIT INSTALLATION OPERATIONFollow the final operational checks outlInstallation Guides.
If further detailed instruction is necessamanual for each of the component partsJCM Commercial Technical Support fo
Figure 31 Filling the Optipay CC
V ting Guide July, 2006
P © 2006, JCM American, Corporation3
CWwDpi
ST[pf
ET
Diagnostic DescriptionRed Yellow Green
olumn and install it onto the top of the 6). rol Board onto the six (6) plastic standoffs of ith plastic screening (Note the circuit board e shown in Figure 7).
t side of the center column using two (2) of previously removed in Step 2 (See Figure 8). light (See Figure 9).
Figure 7 Installing the Control Board onto New Bracket
Mount the Control Board onto the New Ticket Assembly
RemoveFluorescent Tube
Figure 9 Removing Light Tube
art No. 960-100138R_Rev. A 1 0
Figure 30 DBV-301 Error Codes
OFF OFF SOLID DBV / OK / READY
OFF 1 OFF CASH BOX FULL / CHECK CASH BOX
2 OFF OFF STACKER ERROR / CHECK CASH BOX
3 OFF OFF NOTE JAMMED / CHECK NOTE PATH
OFF 4 OFF NOTE JAMMED / CHECK NOTE PATH
OFF 10 OFF CASH BOX POSITION / CHECK CASH BOX
OFF OFF 1-8 LAST NOTE REJECTED / IF PROBLEM PERSISTS EITHER CLEAN NOTE PATH OR CONTACT JCM
OFF OFF 9-10 LAST NOTE INHIBITED / REJECTED BY DBV OR HOST
OFF OFF 11-15 LAST NOTE REJECTED / IF PROBLEM PERSISTS EITHER CLEAN NOTE PATH OR CONTACT JCM
Install NewBracket onthe Right Wallof the Center Column
Figure 8 Installing New Bracket
endo HVV 721/821 Retrofit Kit Retrofitting Guide Retrofit
ASH BOXhen the Recycler is not used, slide the hite release tab located on top of the BV-301 forward (See Figure 28) and ull the Cash Box up and out to remove t.
ENSOR MODULEo remove the Sensor Module, press up 1] on the release rod locking bar and ull the module outward [2] from the rame (See Figure 29).
RROR CODEShe Figure 30 Table lists the DBV-301 LED Error Code flash definitions.
CashBox
ReleaseTab
Slideto
Front
Figure 28 Cash Box Removal
1 Push Rod UpRelease Rod
2 Pull Out
Figure 29 Sensor Module Removal
Sensor Module Error Code Flash Indications
Number of Flashes
Yellow
Green
LED
LEDRed LED
6. Remove plastic screen from center cControl Board Bracket (See Figure
7. Install the previously removed Contthe new Bracket and cover board worientation to the Bracket’s rear edg
8. Install the new bracket onto the righthe 7/16 inch carriage bolts and nuts
9. Remove right side Fluorescent Tube
Figure 6 Reinstalling Plastic onto Control Board Bracket
Reinstall Plastic Screen onto ControlBoard Bracket
V ting Guide July, 2006
P © 2006, JCM American, Corporation9
Locka
F
NGSes between the early and later version
itch settings.
5
6
4
rsion DIP Switch Side Label
4. DIP Switch Locating Arrow5. Interface Connector Pin Label6. Lower DIP Switch Block
DIP Switch Settings
Upper 8 position (Large/Red) DIP Switch Block settings are:
Lower 8 position (Small/White) DIP Switch Block settings are:
1. DIP Switches 1-7 Normally = OFF2. DIP Switch 8 OFF = MDB I/F,
DIP Switch 8 ON = Pulse I/F**See DBV-30X Operations Manual (Part No. 960-000103R) for Pulse I/F settings.
Upper DIP Switch Block Lower DIP Switch Block
Later Version DIP Switches
art No. 960-100138R_Rev. A 4
Port
JCM Lock/
ExtensionPlug into
c
MDB VMC
J10
VMC J9
b
MDBPort toOptipay
Figure 13 Connecting Ports J9 & J10
ExistingMDB/Lock
a
b
Harness
JCM
Harness
MDB/Lock Extension
MatingPlug
igure 12 Connecting MDB Extension
Figure 27 Default
1. OFF = Accept $1 ON = Reject $12. OFF = Accept $5 ON = Reject $53. OFF = Accept $10 ON = Reject $104. OFF = Accept $20 ON = Reject $205. Always = OFF6. Always = OFF 7. Always = OFF8. OFF = Normal ON = Test Mode
endo HVV 721/821 Retrofit Kit Retrofitting Guide Retrofit
10. Drill a 5/32 inch hole in the upper panel that is eight (8) inches from the left door’s hinge, and two (2) inches up from the panel’s bottom (See Figure 10 a).
11. Re-route the door harness from the center column and replace its connector plugs onto the relocated Control Board (See Figure 10 b).
12. Reconnect the Ground Wire using the screw retained in Step 4 on the backside of the newly drilled hole (See Figure 11 a).
13. Reinstall the Fluorescent Tube light (See Figure 11 b).
14. Connect the existing MDB/Lock Harness (See Figure 12 a) into the JCM MDB/Lock Extension Harness mating plug (See Figure 12 b) and route it around the back of the center column up to the VMC circuit board.
15. Connect the Lock Port Plug into J10 of the Vending Machine Controller (VMC) (See Figure 13 a) and the MDB Port Plug into J9 of the VMC (See Figure 13 b).
Re-installLight
b
Re-connect GroundWire Behind
a
Figure 11 Reinstall Light & Ground Wire
Drill Holein Panel
2” 8”
Re-route
3 Connectors
Door Harness& Re-Plug its
a
b
Figure 10 Drill Panel Hole, Re-route Door Harness & Re-Plug
DIP SWITCH LABELS AND SETTIFigure 26 illustrates the label differencDBV-301 DIP Switch Blocks.
Figure 27 defines the DBV-301 DIP Sw
12
3
Early Version Label
Later Version Label
3
Figure 26 Early & Later Ve
1. JCM Logo2. JCM Main Office Address3. Upper DIP Switch Block
Upper DIP Switch Block Lower DIP Switch Block
Early Version DIP Switches
V ting Guide July, 2006
P © 2006, JCM American, Corporation5
M
TtFb
ch Harness (See Figure 14 a) to the JCM (See Figure 14 b). ion Switch Harness around and behind the onnect it into the cabinet’s left side Selection ee Figure 15 b).
2 of the VMC (See Figure 16).the four (4) mounting studs at the Bill (See Figure 17).
nection point will be located behind the
Figure 15 Routing Right Selection Switch Harness
Center ColumnRoute Around
Selection Switch Harness
Left Sidea
bSelection Switch Connector
Left Side
Install Gasket on the4 Mounting Studs
Figure 17 Installing the Kit Gasket
art No. 960-100138R_Rev. A 8
Figure 25 Bottle Mask Mounting Considerations
23
NOTE: If a mounting kit is required, refer to the individual Vendor’s JCM installation guide.
Flush mount90° to Gasket
NOTE: Set all DIP Switches to their appropriate settings as described in the related JCM equipment’s installation guides.
VMCDisplay HarnessPlug J2
Figure 16 Reconnect Display Harness
endo HVV 721/821 Retrofit Kit Retrofitting Guide Retrofit
OUNTING INSTRUCTIONS
he DBV-301 Bottle Mask must be mounted flush to the door surface on top of he kit supplied Gasket (Review Figure 17) without interference as illustrated in igure 25 a. Tighten the four mounting nuts in the order illustrated in Figure 25 .
Caution: Turn the equipment power OFF before removing or replacing any components.
Caution: Tighten mounting nuts until snug. DO NOT over tighten.
1 4
b
FlushMount
Flush mountto Gasket
90°
90°
a
toGasket
InsertGasketon StudsFirst
Gasket
16. Connect the existing Selection SwitSelection Switch Extension Harness
17. Route the cabinet’s right side Selectcenter panel, (See Figure 15 a) and cSwitch Harness mating connector (S
18. Reconnect the Display Harness to J19. Install the kit supplied Gasket onto
Validator Port opening in the frame
NOTE: The left side concenter panel.
Figure 14 Connecting Selection Switch Harness
To J9On VMC
JCMSelectionSwitchExtensionHarness
OldJ9 Plug
Left Select Switch
To
a
b
V July, 2006
P © 2006, JCM American, Corporation7
.
24. Connect the remaining end of the MDB Harness to the machine’s
Machine HarnessMachine Harness
TEPS
into the machine where the previous Coin
tions Cable around the back and up the left ).
CC Communications Connector into the ee Figure 23). CC Communications Connector into the tor (See Figure 24 a).it supplied Cable Ties (See Figure 24 b).
Route RC-10 HarnessUp TheLeft Side
Route RC-10 HarnessUp TheLeft Side
Figure 22 Routing the RC-10 Communications Cable
Figure 24 Making A-66 CC MDB Connection
Connectin the 6-PinInline MolexConnector
bInstallCable Ties
a
art No. 960-100138R_Rev. A 6
MDB Connector on the right side of the DBV-301 (See Figure 20 b).
Figure 20 Installing Cable Ties
PlugPlug
MDBComm HarnessPlug
MDBComm HarnessPlug
a
Connect4-PinMolexConnectorinto RC-10
Figure 23 Making A-66 Coin Changer Comm Connection
endo HVV 721/821 Retrofit Kit Retrofitting Guide
20. Install the RC-10 Bill Recycler onto the Optipay™ DBV-301 Bill Validator (See Figure 18). Refer to Optipay™ RC Installation Guide (JCM Part No. 960-000107R Rev. 3 or greater) to insure proper installation steps.
21. Interconnect the DBV-301 Bill Validator’s Communications Harness to the Optipay™ RC (See Figure 19).
22. Install the combined DBV-301 onto the four (4) mounting studs behind the Gasket and secure it in place using the four (4) #8-32 Kep-Lock Nuts supplied in the kit. Observe the precautions noted in the Mounting Instructions described on page 8.
23. Connect the MDB Communication Harness to the DBV-301 (See Figure 20 a).
Figure 19 Connecting RC to BV
?
DBV-30X 16-pin Plug &Receptacle
Communications Harness
RC-10 16-pin Plug & ReceptacleSlide On
Figure 18 Installing RC onto BV
MDBMDBb
OPTIPAY™ CC INSTALLATION S1. Remove the existing Coin Changer.2. Install the Optipay™ Coin Changer
Changer existed (See Figure 21).3. Route the 4-Pin RC-10 Communica
side of the DBV-301 (See Figure 22
4. Connect the 4-pin Molex Optipay™Optipay™ RC mating receptacle (S
5. Connect the 6-pin Molex Optipay™inline MDB Harness mating connec
6. Secure all cables in place with the k
Figure 21 Installing the A-66 CC
Install theA-66CoinChanger
Top Related