1
Silicon Capacitive Accelerometers
Ulf MeriheinäM.Sc. (Eng.)
Business Development ManagerVTI TECHNOLOGIES
2
Measuring Acceleration
The acceleration measurement is based on Newton’s2nd law: Let the acceleration act on a known proofmass and measure the force acting on it = m * aUsually the spring acts as a force gauge: 1) capacitivemeasurement of deflection, 2) piezoresistive or 3)piezoelectric measurement of strainThe capacitive and piezoresistive principle can be usedto measure DC acceleration (inclination), whereaspiezoelectric sensors have a high pass feature
3
Sensing Element Operation
4
Frequency Response
0,00001
0,0001
0,001
0,01
0,1
1
10
100
0,01 0,1 1 10 100
UnderOverCritic.
Acceleration
SpeedPosition
If the sensor is under-damped, there is aresonance at somefrequency - aphenomenon, which mightnot always be desiredFor frequencies well abovethe resonance the sensormeasures its position(seismometer)In the intermediatefrequency range an over-damped sensor measuresits AC speed
For slow accelerations the deflection of the proof mass inthe sensor coordinates is directly proportional to theacceleration
5
Bulk Micro Machining
(100)
(111)S √2 S
Glass Silicon
- V + V
Bulk micro machiningis using anisotropicetching (wet/dry) toform 3d structures intothe bulk of a singlecrystal siliconWafers are bondedtogether: anodic andfusion bondingLithography, oxidationand thin films(electrodes)
6
Silicon Capacitive Accelerometers
The sensing elementconsists of three layersof siliconProof mass and springsin the mid waferCapacitors one on eachside of the proof massSymmetrical structureGas damping in thehermetically sealedcavityGlass insulation betweenthe electrodes
7
Ideally, the directional dependence of the sensitivity off thenominal measuring axis is a cosine function of the angle ofdeviation from nominal direction: S = S0 * COS(Phi)The measuring direction may be parallel or perpendicular to themounting planeCross-axis sensitivity = maximum sensitivity in the planeperpendicular to the measuring direction relative to the sensitivityin the measuring directionIn the silicon capacitive technology the cross-axis sensitivityresults from alignment errors in the mounting
Measuring Direction &Cross-axis Sensitivity
aPhi
8
3-axis Element
Four triangular spring-proof mass systems. Threeacceleration components can be calculated as linearcombinations of mass tilting angles
mass
X
Y
Z
axis of rotation
centre of gravity
Most of thecapacitance area islocated where most
of the gapdeformation is
formed
9
Sensor Structure
First version dimensions 2.65mm x 2.65mm x 1.2mm.Five layer structure familiar from other VTI sensors.
contactpads
glass gridelectricalfeedthroughs
structuralwafer
capping wafersglass grid
Siliconblock
Silicon block
10
Prototype Results
-180 -135 -90 -45 0 45 90 135 1803.6
3.8
4
4.2
4.4
4.6
4.8
5 3-axis accelerometer rotated in 1g field
Rotation angle [deg]
Cap
acita
nce
[pF]
E2E1E6E8E7E5E4E3
11
Measuring InclinationThe accelerometer can be used as an inclinometerIt measures the combination of the force of earth’s gravityand acceleration: Signal = a + 1g * SIN(ϕ)The sensing element is strongly over-damped (f-3dB ≈ 2 …28Hz) to reduce the influence of accelerationBecause of angular mounting errors (component of cross-axis sensitivity in the plane of inclination) there is an offsetin the sinus function sin(ϕ + ϕ0)
+1g 90°0g 0°G
12
Measuring PositionThe inclinometer can be used to measure position:
L
L * SIN(ϕ)
ϕ
L2
L2 * COS(ϕ2) – L1 * SIN(ϕ1)
L1
ϕ2ϕ1
L1 * COS(ϕ1) + L2 * SIN(ϕ2)
ϕ L * COS(ϕ)L
13
Inclinometers and low-g accelerometers up to a fullrange of about 3g can easily be calibrated in earth’sgravitational fieldHorizontal accelerometer and inclinometer: Normalposition = Zero Position = 0g, +90° turned = +1g + 1g *SIN(ϕ0), - 90° turned = -1g + 1g * SIN(ϕ0) => Sensitivity =[(+90° turned) - (-90° turned)]/2; if the inclinometer fullrange is less than ±90° the full scale angle can be usedas calibration point for SensitivityVertical accelerometer: Normal position = Zero Position= +1g, +90° turned = +0g + 1g * SIN(ϕ0), - 90° turned = -0g - 1g * SIN(ϕ0) => Sensitivity = Normal position - [(+90°turned) + (-90° turned)]/2
Calibration
14
Single crystal silicon
Capacitive sensingHermetically sealedstructures
Symmetrical structures
Customised sensors
Bulk micro machiningProof Mass and Springs in VTI’s Low-g Sensor
Why This Technology?
15
Ideal elastic material: no plastic deformation,tough up to 70 000 g
Single Crystal Silicon
16
Direct measurement of deflectionBased on the variation of a gap between two planarsurfacesThe capacitance or charge storage capacity of a pair ofplates only depends on gap width d and plate area A: C= ε0 * A/dOn one side a force (acceleration) decreases the gapand on the other side increases it: C1 = C01 + C11/(1 - k1 *a), C2 = C02 + C12/(1 + k2 * a)Assuming symmetry and small stray capacitance (or (k *a)2
17
Reduced packaging requirementsReliability: no particles or chemicals canget into the element
Hermetically Sealed Sensor
18
Symmetrical Structures
Improved accelerometer zero stability,linearity and cross-axis sensitivity
Temperature dependencewell below 1 mg/ºCNon-linearity typically below 1%Cross-axis sensitivity typicallyless than 3%
19
Application specific sensitivity andfrequency responseFlexible 2-chip solution
Customised Sensors
SCA600
20
Surface Micro MachinedAccelerometers
Dominating technology for high g-ranges
21
Two Accelerometer Technologies
Ultimate limit: F= m·a = k·x
Adhesion and electrostatic forces start to dominate at small F
Surface and bulk micro machining approach each other
22
Large proof mass, large capacitance enablehigh performance low-g sensingZero stability and noise performance (high resolution)
Noise spectrum (1 - 100 Hz)
1
10
100
1000
10000
0,0 20,0 40,0 60,0 80,0 100,0 120,0
Frequency (Hz)
Nois
e (u
g/sq
rt(Hz
))
Noise (ADXL202)Noise (HML288)Noise(SCA61T)
Noise performance comparison
Bulk Micro Machining
23
Why Two AccelerometerTechnologies?
+ IC-compatible+ Lowest cost+
24
Minimise the effect of stray impedance (capacitance): usevirtual ground and fixed voltagesMinimise electrostatic forces: charge balanceCharge balance principle: Sensing element capacitors C1and C2 are charged with amplitude modulated squarewaves of opposite signs; V1 = Vref + V0 and V2 = -(Vref - V0)in such a way that the net flow of charge ∆Q = 0.Now C1 * (Vref + V0) = C2 * (Vref - V0) and V0 = (C1 - C2)/(C1 +C2) * Vref = linear measure of accelerationNet electrostatic force: ∆F = F1 - F2 ∝ (V1/d1)2 - (V2/d2)2 ∝Q12 - Q22 = 0
Capacitive Sensing Circuitry
AC1C2
V1
V2
∆Q
25
Packaging
10mm
5 mm
Lowest level:Sensor as SMD
First level:Calibrated SMDcomponent
Second level:Stand-aloneaccelerometer
26
Sensing Elements
+ Electronics,ASICs
Sensor Components
SCA610 / SCA600
Stand aloneaccelerometers
SCA320 (z-axis)
Product Concepts
27
Available ranges (g)
SCA61T/100T ±0.5 ±1.0
SCA610 ±0.5 ±1.0 ±1.5 ±1.7SCA600 ±1.0 ±1.5 ±1.7 ±3.0
SCA620/320 ±1.5 ±3.0 ±12.0
SCA111 ±1.2 ±2.0SCA110 ±1.2
VTI Standard Products
28
ABS and TCS keeps slip at max.10%level for maneuverabilityIn All Wheel Drive (AWD) vehicles allwheels may slip (no speed reference)Speed or deceleration/accelerationinformation from inertial sensor,longitudinal accelerometer(v =0∫t a dt + v0 )
Applications: ABS and TCS
29
ABS and TCS are not enough in a curve ESP corrects for under- and over-steering Yaw rate (Ω) and centrifugal
acceleration (aT) from anangular rate sensor and a
lateral accelerometer are compared to those calculated from wheel speed and steering wheel angle (Ω = v/R, aT = v2/R)
Applications: VDC or ESP
30
Vertical accelerometers in the vehicle cornersmeasure body accelerationShock absorbers are adjusted in real-time or inaverage for safe and smooth rideIn advanced systems wheel force is measured withwheel hub accelerometers and vehicle inclination with inclinometersIn vehicles without steering wheel angle sensor alateral accelerometer measures centrifugal force
g
gg
gApplications: ECS
31
Vehicle Tilt Monitoring and Control Digging Depth and Slope Control Train Lateral Force and Vertical Acceleration Monitoring Seismic Monitoring Platform Leveling Inclinometer Instruments Marine Applications Inertial Navigation Medical: Patient Monitoring, Cardiac Pacemakers Sports and Fitness: Motion, position, altitude, energy, ...
Other Applications
32
Applications: ExcavatorInclinometer: Vout = Vdd/2 * ( 1+ k * SIN(Phi))
Digging Position:
1) Z = L * SIN(Phi) & X = L * COS(Phi)[Normally horizontal arm of length L]
2) X = L * SIN(Phi) & Z = L * COS(Phi)[Normally vertical arm of length L]
33
Motor Grader with Inclinometers (a = 1g *SIN(Phi))High Speed Train Inclination and Suspension(aT = v2/R * COS(Phi) = 1g * SIN(Phi)).
Other Vehicle Applications
34
Other MEMS Sensors: AbsolutePressure Sensor
35
Pressure Sensor Sensing Circuitry
Voltage based interface− ∆Vout = V(S2) - [V(S1) + V(S3)]/2 = - C0/C(P) * ∆Vin− C(P) = C1/(1 – P/P0) + C2 => P = P0 * {1 – C1/C * [1 +
(C2/C) + (C2/C)2 + (C2/C)3 + …]}− Sampling before - during - and after the pulse− 3-point calibration gives excellent accuracy
-A
C(P)
C0∆Vin∆Vout
S1 S2 S3
36
Time based interface− Nout = Fout * ∆T = ∆T * VDD/VH/4R * 1/C(P) = k/C(P)− P = P0 * {1 – C1/C * [1 + (C2/C) + (C2/C)2 + (C2/C)3 + …]}− One can add one or two references by switching in constant
capacitors instead of C(P)− The oscillator can be switched off between measurements to reduce
power
-A
C(P)
RFout
Pressure Sensor Sensing Circuitry
37
Other MEMS Sensors: AngularRate Sensor
Based on the same process as the accelerometer
38
Thank You!
Silicon Capacitive AccelerometersMeasuring AccelerationSensing Element OperationFrequency ResponseBulk Micro MachiningSilicon Capacitive AccelerometersMeasuring InclinationSurface Micro Machined AccelerometersTwo Accelerometer TechnologiesPackaging
Top Related