Eng ineered Pipe and Tank S y s t e m s
SPIRAL HDPE PIPELINE SYSTEMS Applications for Long Term Reliability
Diameter: 300mm to 3,000mm (manufactured in Malaysia)
There is an increasing awareness of serious corrosion problems of conventional materials and growing concern about exfiltration problems are the main reasons for the application of our innovative, light, inert and large diameter SPIRAL high density polyethylene pipeline system.
SPIRAL pipe is manufactured through a specially designed profile extrusion process where an extruded profile strip is spirally wound over a mandrel. Overlap on the edge is fused homogeneously together while it is in the hot plastic state, producing a smooth internal surface.
SPIRAL pipe system offers a wide range of fittings and manholes, which are also manufactured by specially designed profile-extrusion process and fabricated by extrusion welding.
PROPERTIES OF HDPE USED UNIT POLYETHYLENE
FOR PRODUCTION OF PIPES PE80 / PE100
Physical Properties
Density g/cm 3 0.938 - 0.962 Melt Flow Index (190°C / 5.0kg) g/10 min 0.25 - 0.85
Mechanical Properties
Tensile Stress at Yield MPa 18 -25
Elongation at Break % > 600
Flexural Modulus MPa 800 - 1100
Shore Hardness - 60 - 65
Minimum Required Strength (MRS) MPa 8 / 10
Thermal Properties
Vicat Softening Point °C 120- 131
Average Coefficient Of Thermal Expansion (20°C - 40°C) mm/m°C 0.15-0.20
Thermal Conductivity W/m°C 0.3 - 0.4
Normal Operating Temperatures for Pipe °C -20 to +50
Advantages of Spiral Pipes • Tough • Light Weight and Easy to 7 • High Chemical Resistance • High Abrasion Resistance • Corrosion Resistance
Jointing Methods
A. Rubber Ring Joint ^
B. Spigot & Socket Fusion Weld Joint
ransport
compare to other pipe material
Longer Service Life Excellent Hydraulics Economical Installation Low Cost Handling at Site
T
Fusion Fillet Weld Joint D. Butt Weld Joint
f
E. Bolted Flange Joint
Trench Cross-Section
Primary Initial Backfill
Bedding
Foundation (If required)
Typically Pipe Dia. + 400 mm
Sewerage Pipelines Drainage Pipelines Culverts Effluent lines Slurry lines Irrigation Waste Gas Ducts and Ventilation Manhole / Manhole Drop Sea Outfall
Relining of Old Pipelines Slotted Drain Application Floats Rubbish Chutes for High-rise Buildings On Site Detention System (OSD) Pipe Jacket - to protect chilled steel water pipe, its annular space filled with foam for insulation Pile Sleeve - to repair or erect new jetty pillar and for marine pile protection and rehabilitation.
Reference Project Lists Using Spiral Pipe • North South Highway Culvert Pipes (1.2m and 1.5m diameter) • Relining ARMCO Pipe at Jalan Tun Razak Kuala Lumpur (3m diameter) • KLIA Runway Drainage (750mm diameter)
Sprial HDPE Flap Gates
Wall mounted |flapTgate!circularttype
Spiral HDPE Flap Gate automatically controls the water flow by opening for discharge and closing to prevent back-flow.
Types of Flap Gate • HDPE Wall Mounted "Spiral" Flap Gate (SQUARE Type) • HDPE Wall Mounted "Spiral" Flap Gate (CIRCULAR Type) • HDPE "Spiral" Flap Gate c/w Spiral Pipe
The standard dimensions are 600mm, 900mm, 1000mm, 1200mm, 1500mm, 1800mm and 2100mm. Custom made flap gate to suit site conditions is available upon request.
"SPIRAL" Pipes Data
P i p e S t a n d a r d : D I N 1 6 9 6 1
ID (mm)
Profile Nr.
Rs24 P N/m
Kg/m Profile Nr.
Rs24 P N/m
Kg/m Profile Nr.
Rs24 P N/m
Kg/m
300 5 9.45 5450 9
400 5 4.15 3200 10
450 5 2.97 2590 12
500 5 2.18 2100 13
533 5 1.85 1850 14
600 5 1.28 1500 15 6 1.66 1900 18
750 5 0.67 1000 19 6 0.86 1250 23 9s 1.51 2200 31
900 5 0.39 700 23 9s 0.89 1550 37 12s 1.78 3100 59
1000 6 0.37 700 30 10s 0.87 1700 51 14s 2.69 5150 85
1200 9s 0.38 900 50 12s 0.77 1800 78 14s 1.60 3700 101
1500 12s 0.40 1150 98 14s 0.84 2400 125 18s 1.55 4450 174
1800 14s 0.49 1700 149 16s 0.79 2750 186 23s 2.09 7200 292
2365 16s 0.39 1750 236 23s 1.03 4550 375
3000 23s 0.48 2750 486
Quick Guide on Burial Depth of "SPIRAL" Pipe Rs24 =E x I N/cm 2
Assumption : 160mm crusher run surrounds the r3
pipe with 95% proctor density compaction. where : Rs24 = Ring Stiffness
Class Approximately Depth of Burial E = Elasticity Modulus F 1m to 4m I = Moment of Inertia G 4m to 8m r = Radius
P = Test load for deflection (24 hours)
Engineered Pipe and Tank Sysi
GEOSEN ASIA PTE. LTD. 74 Geylang Bahru Industrial Estate
#01-2858, Singapore 339682 Tel: 6299 6116 Fax: 6293 9703 Email: [email protected]
Top Related