QUICK START GUIDE
ENGLISH
WHAT’S INCLUDED
» [ 1 ] 80 Watt TC Mod
» [ 1 ] 3.5 ML Built-In Tank
» [ 1 ] Mouthpiece
» [ 1 ] Notch Atomizer 0.25ohm (Pre-Installed)
» [ 1 ] SS316 0.5ohm Atomizer
» [ 1 ] Tank Connector
» [ 1 ] USB Charger
» [ 1 ] User Guide
ATOMIZER PRIMING
TANK FILLING
Before using the VAIO 80w TC mod, there is a very cost saving
measure that all users should take. That is priming the atomizer.
Unscrew the top cap from the device, then proceed to unscrew
the pre-installed 0.25ohm notch atomizer from that top cap. Once
removed, take your e-liquid of choice and proceed to drip 3-5 drops
of e-liquid into the atomizer head. Reattach atomizer to the top cap
and proceed to fill your tank with your e-liquid.
After priming your atomizer and setting it aside, you are now ready
to fill your tank. Take your e-liquid and proceed to fill the tank.
Once you have filled the tank, screw the top cap back onto the
AIRFLOW CONTROL RINGThere are five airflow holes located on the control ring. By rotating
the control ring clockwise, you will expose more of the holes,
sending more air to your atomizer. Feel free to experiment with this
feature, to find your best vape setting.
NOTE: To avoid flooding the atomizer, it is important to only fill
half of the tank. Once the top cap with the attached atomizer is
reattached to the device, the e-liquid with begin to rise. If there is
too much liquid, there is a chance that the tank will flood, as well as
the atomizer.
device. Without pressing the power button, using short breaths,
inhale from the drip tip up to 5 times and allow tank to sit for at
least 10 minutes to give the atomizer time to soak in your liquid.
USING DEVICETo turn on the VAIO 80w TC mod, press the power button five
times, you will do the same to turn off the device as well. Before
using the device, make sure you are in the correct mode depending
on the atomizer you are using. To adjust modes, press the power
button 3 times to enter the designated menu. Once there, use
the – button the navigate the menu and the + button to make any
necessary changes. Once you’ve checked your settings, you are
now ready to vape. Hold the power button while inhaling from
the drip tip, releasing the power button once the desired vapor
production is achieved. Use the + and – buttons to determine the
best wattage or temperature, depending on your atomizer, that
works for your vaping style.
NOTE: When the power button is held for longer than 10 seconds,
the device will no longer fire and the screen will display, “Over 10s
Protection.”
TEMPERATURE CONTROLIncluded in your VAIO 80w TC packaging is the SS316 0.5ohm
atomizer. This unique atomizer gives users the ability to vape in
both wattage and temperature mode. Please refer to the atomizer
priming section of the quick start, before using this atomizer. If you
are planning to use this atomizer in temperature mode, press the
power button 3 times to enter the designated menu. Once in the
menu, press the – button, you will notice that the modes will begin
to flash. Now, press the + button to scroll through the different
modes. Once you find the mode labeled SS316, you are now ready
NOTE: When using new atomizers in temperature control mode, it
is important to start at lower temperatures to avoid burning your
atomizer.
to vape using the provided stainless steel atomizer. Using the +
and – buttons you can adjust your temperature to find the best
temperature for your e-liquid.
BATTERY LIFEThere is a battery meter at the bottom of your screen, that will
display the device’s current battery strength. As you use the device,
this meter will continue to decrease until the device can no longer
fire and the “Low Battery” message is displayed on the screen.
Once this message is displayed, use the USB cord included with the
device and proceed to charge.
NOTE: While the device is charging, you can still enjoy your
favorite e-liquid. Keep in mind, while it is possible to continue use
during charging, it drastically slows down the process.
USB PORT
UP BUTTONDOWN BUTTON
POWER BUTTON/FIRE BUTTON
OLED DISPLAY
MOUTHPIECE
AIRFLOW CONTROL
WARNINGDo not attempt to modify equipment; doing so can result in
permanent damage, overheating and/or explosion which may lead
to severe injuries or death.
For more information visit: vaporfi.com/how-it-works
DISCLAIMERVaporfi products are not smoking cessation products and have not been tested as such. The U.S. FDA has not approved these products for any use and they are not intended to diagnose, cure, mitigate, treat or prevent any disorder, disease, or physical or mental condition. Some Vaporfi products contain a chemical known to the State of California to cause cancer or birth defects or other reproductive harm. Nicotine is addictive and habit forming, and it is very toxic by inhalation, in contact with the skin, or if swallowed.
GUIA DE INICIO
ESPAÑOL
¿QUÉ VIENE INCLUIDO?
» [ 1 ] 80 Watt TC Mod
» [ 1 ] Tanque Incorporado de3.5 ML
» [ 1 ] Boquilla
» [ 1 ] Atomizador Notch 0.25ohm (Pre-Instalado)
» [ 1 ] Atomizador SS316 0.5ohm
» [ 1 ] Conector de Tanque
» [ 1 ] Cargador USB
» [ 1 ] Guia de Usuario
CEBADO DE LA CABEZA DEL ATOMIZADOR
LLENADO DEL TANQUE
Antes de utilizar el VAIO 80 TC mod, hay algo que todos los usuarios deberían hacer para ahorrar mucho. Esto es curar el atomizador. Desatornille la tapa superior del cuerpo del tanque, luego proceda a desatornillar el atomizador de 0,25ohm preinstalado de la tapa que acaba de retirar. Una vez hecho esto, tome su líquido preferido y proceda a verter 3 a 5 gotas en la cabeza del atomizador. Vuelva a unir el atomizador a la tapa superior y proceda a llenar el tanque con líquido.
Luego de curar su atomizador y separarlo, estará listo para llenar el tanque. Tome su líquido preferido y proceda a llenar el tanque. Una vez lleno, atornille la tapa superior al tanque. Utilizando
ANILLO DE CONTROL DE FLUJO DE AIREHay cinco agujeros de control de flujo de aire en el anillo de control. Al rotar el anillo de control en sentido horario, expondrá más agujeros, enviando más aire al atomizador. Siéntase libre de experimentar con esta característica para encontrar la mejor configuración para usted.
NOTA: Para evitar rebalsar el atomizador, es importante que llene solo la mitad del tanque. Una vez que vuelva a colocar la tapa superior con el atomizador adjunto, el líquido comenzará a subir. Si hay demasiado líquido, podría rebalsar el tanque y el atomizador.
respiraciones cortas, inhale desde la punta de goteo hasta 5 veces y permítale al tanque estancarse por lo menos por 10 minutos para darle al atomizador tiempo para empaparse en el líquido.
UTILIZACIÓN DEL DISPOSITIVOPara encender el VAIO 80w, presione el botón de encendido cinco veces, repita el mismo procedimiento para apagarlo. Antes de utilizar el dispositivo, asegúrese de que está configurado en el modo correcto dependiendo del atomizador que usará. Para cambiar de modo, presione el botón de encendido 3 veces para ingresar al menú designado. Una vez allí, utilice el botón – para navegar el menú y el botón + para realizar cambios. Una vez que haya terminado de configurarlo, estará listo para vaporizar. Mantenga presionado el botón de encendido mientras inhala desde la punta de goteo, soltándolo una vez que se haya alcanzado la producción de vapor deseada. Utilice los botones + y – para determinar el mejor voltaje o temperatura, dependiendo de su atomizador, para su estilo de vaporización.
CONTROL DE TEMPERATURAEn el paquete de su VAIO 80w TC se incluye el atomizador SS316 de 0,5ohm. Este atomizador único les da a los usuarios la posibilidad de vaporizar en el modo de voltaje y temperatura. Por favor, refiérase a la sección de curado del atomizador de la guía de inicio rápido antes de utilizar este atomizador. Si planea utilizarlo en el modo de temperatura, presione el botón de encendido 3 veces para ingresar al menú designado. Una vez allí, presione el botón- y notará que los modos comenzarán a parpadear. Ahora presione el botón + para deslazarse por los diferentes modos. Una vez que encuentre el modo denominado “SS316”, estará listo para vaporizar
NOTA: Si mantiene presionado el botón de encendido por más de 10 segundos, el dispositivo dejará de funcionar y la pantalla mostrará “Protección de 10s”.
utilizando el atomizador de acero inoxidable. Utilizando los botones + y -, podrá ajustar la temperatura para encontrar la que mejor funcione con su líquido.
NOTA: Al utilizar atomizadores nuevos en el modo de control de temperatura, es importante comenzar en temperaturas bajas para evitar quemar el atomizador.
DURACIÓN DE LA BATERÍAHay un medidor de batería en la parte inferior de la pantalla que mostrará el estado actual de la batería del dispositivo. A medida que use el dispositivo, el medido continuará disminuyendo hasta que el dispositivo ya no pueda encenderse y aparezca el mensaje “Batería baja” en la pantalla. Una vez que se muestra este mensaje, utilice el cable USB incluido con el dispositivo y proceda a cargarlo.
NOTA: Cuando el dispositivo se está cargando, podrá seguir disfrutando de su líquido favorito. Tenga en cuenta que, a pesar de que es posible utilizar el dispositivo mientras se carga, hacerlo disminuirá la velocidad de carga drásticamente.
PUERTO USB
BOTON DE ARRIBABOTON DE ABAJO
BOTON DE ENCENDIDO
PANTALLA OLED
BOQUILLA
CONTROL DE FLUJO DE AIRE
ADVERTENCIANo intente modificar el equipo; hacerlo puede resultar en daño permanente, sobrecalentamiento y/o una explosión que puede provocar lesiones graves o la muerte.
Por más información visite: vaporfi.com/how-it-works
EXENCIÓN DE RESPONSABILIDADLos productos Vaporfi no son productos para dejar de fumar ni se han probado como tales. La FDA de los EE .UU. no ha aprobado estos productos para ningún uso ni están indicados para diagnosticar, curar, mitigar, tratar o prevenir cualquier trastorno, enfermedad, o condición física o mental. Algunos productos de Vaporfi contienen una sustancia química que el Estado de California considera causante de cancer o de defectos congénitos y otros daños reproductivos. La nicotina es adictiva y puede crear hábito. Asi mismo, resulta muy tóxica por inhalación, contacto con la piel o por ingestión.
VAPORFI.COM