© 2014 553_Q - 02/141A Watts Water Technologies Company
InteriorWall
5 feet1.5 m
ExteriorWall
1. Location
2. Remove Mounting Base
3. Install Mounting Base
3 1/4”(83 mm)
ThermostatBase
Stud
GangBox
Wall
StudThermostat
Base
BehindDoor
tekmarNet® Thermostat 553
Quick Setup Guide
553_Q02/14
Zoning Replaces: 01/14
© 2014 553_Q - 02/142A Watts Water Technologies Company
4. Switch Settings
5. Wiring
Switch Position Action
1ON LOCK Access level
adjustment is not available.
OFF UNLOCK Access level adjustment is available.
tekmarNet Thermostat 553Two Stage Heat, One Stage Cool, Fan
SwitchSettings
www.tekmarcontrols.com
Lock
edck
/
ON
1 2
Back of Thermostat
tekmarNet®4 Wiring Example
See 553_A for complete wiring details.
WRYG
OptionalOutdoorSensor
070
OptionalSlab
Sensor079Furnace
andAir Conditioner
tN4 Wiring Center or Zone Manager
tN4 C WR
CtN2
tN4tN2
RRh W Rc Y G/O S1 S2ACC Com
No Power
WRYG
OptionalOutdoorSensor
070
OptionalSlab
Sensor079Furnace
andAir Conditioner
tN2 Wiring Center,House Control orZone Manager
tN2 tN2
CtN2
tN4tN2
RRh W Rc Y G/O S1 S2ACC Com
No Power
tekmarNet®2 Wiring Example
© 2014 553_Q - 02/143A Watts Water Technologies Company
6. Install the Thermostat
7. User Interface
ThermostatFront
Push
ThermostatBase
Adjustthe Time
Adjust theSchedule
Display Humidity, Heat & Cool settings, Floor or Outdoor temperature
Away Key
Switch betweenAuto, Heat, Cool, Off &
Emergency Mode Return to the ‘Home’ Screen from any menuAdjust the
Temperature
RoomTemperature
Turn the Fan on
HomeButton
All specifications are subjectto change without notice
4 553_Q - 02/14.
Product design, software and literature are Copyright ©2014 by tekmar Control Systems Ltd., A Watts Water Technologies Company. Head Offi ce: 5100 Silver Star Road, Vernon, B.C. Canada V1B 3K4, 250-545-7749, Fax. 250-545-0650 Web Site: www.tekmarControls.com
The following settings are essential to the successful operation of the system.Step 1: Set switch setting #1 and tekmarNet® system control located in the mechanical room to Unlock to change Access level to Installer. Return to Lock setting once installation has been completed.Step 2: Press and hold “Home” button for 3 seconds to enter programming menus.Step 3: Touch NEXT to locate the Setup Menu and touch ENTER.
8. Critical Settings
Setup Menu Settings Range Default
SENSOR 1Select the type of sensor connected to auxiliary sensor input 1.
OFF, ROOM, FLOR (floor), COIL, DUCT OFF
SENSOR 2Select the type of sensor connected to auxiliary sensor input 2.
OFF, ROOM, FLOR (floor), OUT (outdoor) OFF
ROOM SENSORSelect if the built-in room temperature sensor is on or off.
OFF or ON ON
HUMIDITY SENSORSelect if the built-in humidity sensor is on or off.
OFF or ON ON
Y RELAYSelect the cooling equipment the Y relay operates.
OFF, HP (heat pump), AC (air conditioner), HUM (humidity)
AC
W TERMINAL UNITSelect the terminal unit type of the first stage of heat W.
NONE, HRF1, HRF2, CONV, COIL, FURN, OTHR
HRF1 (tekmarNet®
System Control)OTHR (standalone)
ACC RELAYSelect the operation of the accessory relay.
OFF, W2, HUM, DHUM, HRV, FAN W2
W2 TERMINAL UNITSelect the type of backup heating.
CONV, COIL, FURN (furnace), OTHR (other) FURN
W2 SOURCESelect the second stage W2 hydronic heat source.
BOIL, TANK, MIX BOIL
G/O RELAYSelect the equipment the G / O relay operates.
FAN or OFF (conventional heating)O or B (heat pump)
FAN (conventional)O (heat pump)
For a full list of settings and operational details, please refer to the thermostat Installation and Operation Manual (553_D) available from www.tekmarControls.com
© 2014 553_Q - 02/145Une Entreprise de Watts Water Technologies
1. Emplacement
2. Retirez la base de montage
3. Installez la base de montage
3 1/4”(83 mm)
ThermostatBase
Stud
GangBox
Wall
StudThermostat
Base
Derrièreporte
Mur extérieur
Mur intérieur
5 pi.1,5 m
Mur
Base de thermostat
Base de thermostat
Commutateur boîte
Goujon
Goujon
tekmarNet® Thermostat 553
Guide d'installation rapide
553_Q02/14
Zonage Remplace: 01/14
© 2014 553_Q - 02/146Une Entreprise de Watts Water Technologies
WRYG
OptionalOutdoorSensor
070
OptionalSlab
Sensor079Furnace
andAir Conditioner
tN4 Wiring Center or Zone Manager
tN4 C WR
CtN2
tN4tN2
RRh W Rc Y G/O S1 S2ACC Com
No Power
4. Réglages des commutateurs
5. Filage
Commutateur Position Action
1
ONVERROUILLAGE Le réglage du niveau d'accès n'est pas disponible.
OFFDÉVERROUILLAGE Le réglage du niveau d’accès est disponible.
tekmarNet Thermostat 553Two Stage Heat, One Stage Cool, Fan
SwitchSettings
www.tekmarcontrols.com
Lock
edck
/
ON
1 2
Dos du thermostat
tekmarNet®4 exemple de filage
Référence 553_A pour plus de détails sur le filage complet.
WRYG
OptionalOutdoorSensor
070
OptionalSlab
Sensor079Furnace
andAir Conditioner
tN2 Wiring Center,House Control orZone Manager
tN2 tN2
CtN2
tN4tN2
RRh W Rc Y G/O S1 S2ACC Com
No Power
tekmarNet®2 exemple de filage
Capteurde dalle079 (en option)
Capteurde dalle079 (en option)
Capteur extérieur 070(en option)
Capteur extérieur 070(en option)
Fourneau et Climatiseur
Fourneau et Climatiseur
tN4 contrôle des zones
tN2 contrôle des zones
© 2014 553_Q - 02/147Une Entreprise de Watts Water Technologies
6. Installer le Thermostat
7. Interface d’utilisateur
ThermostatFront
Push
ThermostatBase
HomeButton
Régler l’heure
Régler le programme
Clè à distance
Basculer entre Auto, Chaud,
Frais, Off & mode d’urgence
Régler latempérature
Affichage de l’humidité, des paramètres de chaleur et du frais, de la température ambiante ou du sol
Température de la chambre
Allumer la ventillation
Bouton daccueil. Revenir à l’écran «Home» (Accueil) depuis n’importe quel menu. Appuyez et maintenez enfoncé pendant 3 secondes pour accéder aux menus de programmation.
Base de thermostat
Façade du thermostat
Poussoir
Toutes spécifications sont sujettes à changements sans préavis. Imprimé au Canada.
8 553_Q - 02/14.
Conception de produit, logiciel et littérature sont des droits réservés ©2014 par tekmar Control Systems Ltd., Une Entreprise de Watts Water Technologies. Bureau Principal: 5100 Silver Star Road, Vernon, B.C. Canada V1B 3K4, 250-545-7749, Téléc: 250-545-0650 Site Web: www.tekmarControls.com
Les paramètres suivants sont essentiels au bon fonctionnement du système.Étape 1: Définir le réglage du commutateur sur #1 et le système de contrôle tekmarNet® situé dans la salle mécanique sur Déverrouiller pour changer le niveau d’accès à l’installateur. Retour pour Verrouiller réglage, une fois l’installation terminée.Étape 2: Appuyez et maintenez le bouton «Home» pendant 3 secondes pour entrer dans les menus de programmation.Étape 3: Touchez SUIVANT pour localiser le menu de configuration et appuyez sur ENTRER.
8. Paramètres critiques
Réglages du menu de configuration Gamme Par défautCAPTEUR 1Sélectionner le type de capteur relié à l’entrée auxiliaire du capteur 1.
OFF, ROOM, FLOR (sol), COIL, DUCT OFF
CAPTEUR 2Sélectionner le type de capteur relié à l’entrée auxiliaire du capteur 2.
OFF, ROOM, FLOR (sol), OUT (en plein air) OFF
CAPTEUR DE CHAMBRESélectionnez si le capteur intégré de la température ambiante est allumé ou éteint.
OFF ou ON ON
CAPTEUR D'HUMIDITÉSélectionnez si le capteur d'humidité intégré est activé ou pas.
OFF ou ON ON
RELAIS YSélectionnez l'équipement de refroidissement que relais Y active.
OFF, HP (pompe à chaleur), AC (climatiseur), HUM (humidité)
AC
UNITÉ DU TERMINALE WSélectionnez le type d’unité du terminal de la première étape de chauffage W.
NONE, HRF1, HRF2, CONV, COIL, FURN, OTHR
HRF1 (tekmarNet®
Contrôle de Système)OTHR (autonome)
RELAIS ACCESSOIRESélectionnez l’appareil que le relais accessoire active.
OFF, W2, HUM, DHUM, HRV, FAN (ventilateur) W2
UNITÉ DU TERMINALE W2Sélectionnez le type de chauffage d'appoint.
CONV, COIL, FURN (fourneau), OTHR (autre) FURN
SOURCE DE W2Sélectionnez la source de chaleur hydroniques de la deuxième étape W2.
BOIL (ébullition), TANK (réservoir), MIX (melange) BOIL (ébullition)
RELAIS G/OSélectionnez l'équipement le relais G / O est ouvert.
FAN (ventilateur) ou OFF (chauffage conventionnel)O ou B (pompe à chaleur)
FAN (ventilateur) (classique)O (pompe à chaleur)
Pour une liste complète des paramètres et les détails opérationnels, s’il vous plaît se référer à l’installation du thermostat et mode d’emploi (553_D) disponible sur www.tekmarControls.com
© 2014 553_Q - 02/149Una Compañía de Watts Water Technologies
1. Ubicación
2. Quite la base de montaje
3. Instalación de la base de montaje
3 1/4”(83 mm)
ThermostatBase
Stud
GangBox
Wall
StudThermostat
Base
Detrásde la puerta
Pared exterior
Pared interior
5 pies1,5 m
Base del termostato
Base del termostato
ParedCaja de
interruptor
tekmarNet® Thermostat 553
Guía de instalación rápida
553_Q02/14
División en zonas
Remplazado por: 01/14
© 2014 553_Q - 02/1410Una Compañía de Watts Water Technologies
4. Ajustes del interruptor
5. Cableado
Interruptor Posición Acción
1
ONLOCK (BLOQUEADO) el nivel de acceso para ajustes se encuentra bloqueado.
OFFUNLOCK (DESBLOQUEADO) el nivel de acceso para ajustes se encuentra disponible.
tekmarNet Thermostat 553Two Stage Heat, One Stage Cool, Fan
SwitchSettings
www.tekmarcontrols.com
Lock
edck
/
ON
1 2
Parte trasera del termostato
tekmarNet®4 ejemplo de cableado
Referencia 553_A para detalles completos del cableado.
WRYG
OptionalOutdoorSensor
070
OptionalSlab
Sensor079Furnace
andAir Conditioner
tN4 Wiring Center or Zone Manager
tN4 C WR
CtN2
tN4tN2
RRh W Rc Y G/O S1 S2ACC Com
No Power
WRYG
OptionalOutdoorSensor
070
OptionalSlab
Sensor079Furnace
andAir Conditioner
tN2 Wiring Center,House Control orZone Manager
tN2 tN2
CtN2
tN4tN2
RRh W Rc Y G/O S1 S2ACC Com
No Power
tekmarNet®2 ejemplo de cableado
Caldera y acondicionador de aire
Caldera y acondicionador
de aire
tN4 control de zonas
tN2 control de zonas
Sensor de exterior opcional 070
Sensor de exterior opcional 070
Sensor de losa opcional 079
Sensor de losa opcional 079
© 2014 553_Q - 02/1411Una Compañía de Watts Water Technologies
6. Instalación del termostato
7. Interfaz del usuario
ThermostatFront
Push
ThermostatBaseBase del
termostato
Frente del termostato
Eempuje
HomeButton
Ajustarhora
Temperatura ambiente
Prender el ventilador
Botón Inicio. Vuelva a la pantalla inicial desde cualquier otro menú. Mantenga presionado por 3 segundos para acceder al menú del programa.
Ajustar la programación
Tecla de salida
Ajustar la temperatura
Elija entre Auto (Automático),Heat (Calefacción),
Cool (Refrigeración), Off (Apagado) y Emergency
Mode (Modo de emergencia)
Mostrar los ajustes de humedad, calefacción y refrigeración, la temperatura del Piso y Externa.
Todas las especificaciones pueden cambiar sin previo aviso.
12 553_Q - 02/14.
El diseño del producto, software y la literatura poseen derechos reservados ©2014 a nombre de tekmar Control Systems Ltd., Una Compañía de Watts Water Technologies Ofi cina Principal: 5100 Silver Star Road, Vernon, B.C. Canadá V1B 3K4, 250-545-7749, Fax. 250-545-0650 Sitio web: www.tekmarControls.com
Las siguientes configuraciones son esenciales para que el sistema trabaje de manera correcta.Paso 1: Desbloquee (opción UNLOCK) el ajuste número uno del interruptor y del control del sistema tekmarNet® para cambiar el nivel de accesibilidad a Instalador. Cámbielo nuevamente a Bloquear (opción Lock) luego de finalizar la instalación.Paso 2: Mantenga presionado el botón “Home” por 3 segundos para ingresar a los menús de programación.Paso 3: Presione el botón NEXT (SIGUIENTE) para localizar el menú de SETUP (Instalación) y presione ENTER (ENTRAR).
8. Ajustes críticos
Ajustes del menú de instalación Rango PredeterminadoSENSOR 1Seleccione el tipo de sensor conectado a la entrada número 1 para sensor auxiliares.
OFF, ROOM, FLOR (piso), COIL, DUCT OFF
SENSOR 2Seleccione el tipo de sensor conectado a la entrada número 2 para sensor auxiliares.
OFF, ROOM (ambiente), FLOR (piso), OUT (exterior) OFF
SENSOR AMBIENTEPrenda o apague el sensor integrado de la temperatura del aire en el ambiente.
OFF o ON ON
SENSOR DE HUMEDADSeleccione si el sensor de humedad integrado estará prendido o apagado.
OFF o ON ON
RELÉ YSeleccione el equipo de refrigeración que accionara el relé Y.
OFF, HP (bomba de calor), AC (acondicionador de aire), HUM (humedad)
AC
TIPO DE TERMINAL WSeleccione el tipo de unidad terminal de la primera etapa de calefacción W.
NONE (Ninguna), HRF1, HRF2, CONV, COIL, FURN, OTHR
HRF1 (Sistema de control tekmarNet ®)OTHR (Otro)
RELÉ ADICIONALSeleccione el equipo que el relé adicional accionará.
OFF, W2, HUM, DHUM, HRV, FAN W2
TIPO DE TERMINAL W2Seleccione el tipo de calefacción de respaldo.
CONV, COIL, FURN (caldera), OTHR (otro) FURN
FUENTE W2Seleccione la fuente de calefacción hidrónica W2 de segunda etapa.
BOIL, TANK, MIX BOIL
RELÉ G/OSeleccione el equipo que el relé G /O utiliza.
FAN (ventilador) o OFF(calefacción convencional)O o B (bomba de calefacción)
FAN (onvencional)O (bomba de calefacción)
Para una lista completa de ajustes y detalles funcionales, por favor diríjase al Manual de Instalación y manejo del termostato (553_D) disponible en www.tekmarControls.com
Top Related