8/10/2019 OptiX RTN 600 Installation Guide_2
1/168
OptiX RTN 600 Radio Transmission System
V100R001
Installation Guide
Issue 06
Date 2007-12-30
Part Number 31501910
Huawei Technologies Proprietary
8/10/2019 OptiX RTN 600 Installation Guide_2
2/168
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. For any
assistance, please contact our local office or company headquarters.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: [email protected]
Copyright 2007 Huawei Technologies Co., Ltd. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written
consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are the property of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but the statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Proprietary
mailto:[email protected]://www.huawei.com/8/10/2019 OptiX RTN 600 Installation Guide_2
3/168
Contents
About This Document.....................................................................................................................1
1 Before You Start..........................................................................................................................1-1
1.1 Installation Flow..............................................................................................................................................1-2
1.2 Preparing Documents and Tools ....................................................................................................................1-21.2.1 Documents..............................................................................................................................................1-2
1.2.2 Tools.......................................................................................................................................................1-3
1.3 Checking Installation Conditions....................................................................................................................1-3
1.3.1 Checking the Installation Conditions of the IDU...................................................................................1-3
1.3.2 Checking the Installation Conditions of the ODU.................................................................................1-4
1.3.3 Checking the Lightning-Proof and Grounding System..........................................................................1-4
1.3.4 Checking the Power System...................................................................................................................1-5
1.3.5 Checking Auxiliary Devices and Cables................................................................................................1-6
1.4 Unpacking the Equipment...............................................................................................................................1-7
1.4.1 Checking the Equipment........................................................................................................................1-7
1.4.2 Unpacking Crates...................................................................................................................................1-9
1.4.3 Unpacking Cartons...............................................................................................................................1-11
1.4.4 Unpacking Boards................................................................................................................................1-12
2 Installing the IDU......................................................................................................................2-1
2.1 Introduction to the IDU...................................................................................................................................2-2
2.2 Installing the IDU in a Cabinet.......................................................................................................................2-4
2.3 Installing the IDU on the Wall........................................................................................................................2-9
2.3.1 Installing the IDU 610 That Has Wall-Mounting Holes on the Wall..................................................2-10
2.3.2 Installing the IDU 620 That Has Wall-Mounting Holes on the Wall..................................................2-12
2.3.3 Installing the IDU That Does Not Have Wall-Mounting Holes on the Wall.......................................2-15
2.4 Installing the IDU on a Desk.........................................................................................................................2-18
2.4.1 Installing the IDU 610 on a Desk.........................................................................................................2-18
2.4.2 Installing the IDU 620 on a Desk.........................................................................................................2-20
2.5 Installing an E1 Panel ...................................................................................................................................2-21
3 Installing IDU Cables................................................................................................................3-1
3.1 Installing the IDU Protection Grounding Cable..............................................................................................3-2
3.2 Installing the Protection Grounding Cable of the E1 Panel ...........................................................................3-2
3.3 Installing the Power Cable..............................................................................................................................3-4
OptiX RTN 600 Radio Transmission System
Installation Guide Contents
Issue 06 (2007-12-30) Huawei Technologies Proprietary i
http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://00-3%20about%20this%20document.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://00-3%20about%20this%20document.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
4/168
3.4 Installing the IF Jumper...................................................................................................................................3-5
3.5 Installing the Service Signal Cable.................................................................................................................3-7
3.5.1 Installing the Fiber Jumper.....................................................................................................................3-7
3.5.2 Installing the STM-1e Cable..................................................................................................................3-9
3.5.3 Installing the E1 Cable (from the PO1/PH1 Board to the External Equipment)..................................3-10
3.5.4 Installing the E1 Cable (from the PO1/PH1 Board to the E1 Panel)...................................................3-12
3.5.5 Installing the Ethernet Service Network Cable....................................................................................3-13
3.6 Installing the Auxiliary Cable.......................................................................................................................3-14
3.6.1 Installing the Network Management Cable..........................................................................................3-14
3.6.2 Installing the External Clock Cable/Wayside Service Cable...............................................................3-16
3.6.3 Installing the Orderwire Line...............................................................................................................3-17
3.6.4 Installing the External Alarm Cable.....................................................................................................3-18
3.6.5 Installing the Asynchronous Data Cable..............................................................................................3-20
3.7 Cabling and Bundling....................................................................................................................................3-213.7.1 Cabling.................................................................................................................................................3-22
3.7.2 Bundling...............................................................................................................................................3-22
3.7.3 Bundling Fiber Jumpers.......................................................................................................................3-23
4 Installing the 7 GHz - 38 GHz ODU.......................................................................................4-1
4.1 Introduction to the ODU.................................................................................................................................4-2
4.2 Installing OneODU on One Antenna (Direct Mount)....................................................................................4-3
4.2.1 Installing the Antenna............................................................................................................................4-3
4.2.2 Setting the Antenna Polarization............................................................................................................4-3
4.2.3 Installing the ODU on the Antenna........................................................................................................4-54.3 Installing Two ODUs on One Antenna (Direct Mount)..................................................................................4-7
4.3.1 Installing the Antenna............................................................................................................................4-8
4.3.2 Setting the Antenna Polarization............................................................................................................4-8
4.3.3 Installing the Hybrid Coupler on the Antenna.......................................................................................4-8
4.3.4 Installing the ODU on the Hybrid Coupler..........................................................................................4-10
4.4 Installing the ODU (Separate Mount)...........................................................................................................4-12
4.4.1 Installing the Antenna..........................................................................................................................4-13
4.4.2 Setting the Antenna Polarization..........................................................................................................4-13
4.4.3 Installing the Separate Mount Parts.....................................................................................................4-13
4.4.4 Installing the ODU onto the ODU Adapter..........................................................................................4-16
5 Installing the 6 GHz ODU........................................................................................................5-1
5.1 Introduction to the 6 GHz ODU......................................................................................................................5-2
5.2 One ODU Using One Antenna........................................................................................................................5-4
5.2.1 Installing the Antenna............................................................................................................................5-4
5.2.2 Setting the Antenna Polarization............................................................................................................5-4
5.2.3 Installing the 6 GHz ODU on a Pole......................................................................................................5-4
5.2.4 Connecting the ODU to the Antenna.....................................................................................................5-6
5.3 Two ODUs Sharing One Antenna...................................................................................................................5-9
5.3.1 Installing the Antenna............................................................................................................................5-9
Contents
OptiX RTN 600 Radio Transmission System
Installation Guide
ii Huawei Technologies Proprietary Issue 06 (2007-12-30)
http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
5/168
5.3.2 Setting the Antenna Polarization............................................................................................................5-9
5.3.3 Installing the 6 GHz ODU on a Pole......................................................................................................5-9
5.3.4 Connecting the ODUs to the Antenna..................................................................................................5-11
6 Installing ODU Cables..............................................................................................................6-16.1 Installing the ODU Protection Grounding Cable............................................................................................6-2
6.2 Installing the IF Cable.....................................................................................................................................6-3
6.3 Routing and Bundling the IF Cable.................................................................................................................6-6
6.4 Grounding the IF Cable...................................................................................................................................6-6
6.4.1 Grounding Points of the IF Cable..........................................................................................................6-6
6.4.2 Grounding the IF Cable..........................................................................................................................6-9
6.4.3 Installing the Grounding Clip...............................................................................................................6-10
7 Checking the Installation.........................................................................................................7-1
7.1 Checking the Installation of the IDU..............................................................................................................7-27.2 Checking the Installation of the ODU.............................................................................................................7-5
A Terminating theIF Cable with Connectors........................................................................A-1
B Waterproofing Outdoor Connectors.....................................................................................B-1
C Checking the Cable Circuit....................................................................................................C-1
D Engineering Labels for Indoor Cables................................................................................ D-1
D.1 Introduction to Labels....................................................................................................................................D-2
D.1.1 Labels for Power Cables.......................................................................................................................D-2
D.1.2 Labels for Signal Cables.......................................................................................................................D-2
D.2 PreparingLabels............................................................................................................................................D-3
D.2.1 PrintingLabels......................................................................................................................................D-3
D.2.2 WritingLabels......................................................................................................................................D-4
D.3 Affixing Labels..............................................................................................................................................D-4
D.3.1 Affixing a Label to a Power Cable.......................................................................................................D-4
D.3.2 Affixing a Label to a Signal Cable.......................................................................................................D-5
D.4 Common Engineering Labels........................................................................................................................D-6
D.4.1 Engineering Labels for Cabinet Power Cables.....................................................................................D-6
D.4.2 Engineering Labels for Optical Fibers.................................................................................................D-7D.4.3 Engineering Labels for Trunk Cables.................................................................................................D-10
D.4.4 Engineering Labels for IF Jumpers....................................................................................................D-12
D.4.5 Engineering Labels for Network Cables............................................................................................D-13
D.4.6 Engineering Labels for External Alarm Cables..................................................................................D-14
E Engineering Labels for Outdoor IF Cables..........................................................................E-1
E.1 Engineering Labels for IF Cables...................................................................................................................E-2
E.2 Binding the Labels for IF Cables................................................................................................................... E-2
F Glossary.......................................................................................................................................F-1
G Acronyms and Abbreviations............................................................................................... G-1
OptiX RTN 600 Radio Transmission System
Installation Guide Contents
Issue 06 (2007-12-30) Huawei Technologies Proprietary iii
http://02-g%20acronyms%20and%20abbreviations.pdf/http://02-f%20glossary.pdf/http://02-e%20engineering%20labels%20for%20outdoor%20if%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-c%20checking%20the%20cable%20circuit.pdf/http://02-b%20waterproofing%20outdoor%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://02-g%20acronyms%20and%20abbreviations.pdf/http://02-f%20glossary.pdf/http://02-e%20engineering%20labels%20for%20outdoor%20if%20cables.pdf/http://02-e%20engineering%20labels%20for%20outdoor%20if%20cables.pdf/http://02-e%20engineering%20labels%20for%20outdoor%20if%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-c%20checking%20the%20cable%20circuit.pdf/http://02-b%20waterproofing%20outdoor%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
6/168
Index.................................................................................................................................................i-1
Contents
OptiX RTN 600 Radio Transmission System
Installation Guide
iv Huawei Technologies Proprietary Issue 06 (2007-12-30)
http://03-index.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
7/168
Figures
Figure 1Wearing an ESD wrist strap......................................................................................................................5
Figure 1-1Straightening the tongue...................................................................................................................1-10
Figure 1-2Removing the cover .........................................................................................................................1-10
Figure 1-3Removing the surrounded wooden boards.......................................................................................1-11
Figure 1-4Unpacking the carton........................................................................................................................1-12
Figure 1-5Unpacking the boards.......................................................................................................................1-13
Figure 2-1IDU 610..............................................................................................................................................2-2
Figure 2-2IDU 620..............................................................................................................................................2-2
Figure 2-3IDU 610 chassis with wall-mounting holes........................................................................................2-3
Figure 2-4IDU 620 chassis with wall-mounting holes........................................................................................2-3
Figure 2-5IDU 610 chassis without wall-mounting holes...................................................................................2-4
Figure 2-6IDU 620 chassis without wall-mounting holes...................................................................................2-4
Figure 2-7Rack-mounting ears for the 19-inch cabinet.......................................................................................2-5
Figure 2-8Rack-mounting ears for the ETSI cabinet of the IDU 610.................................................................2-6Figure 2-9Rack-mounting ears for the ETSI cabinet of the IDU 620.................................................................2-6
Figure 2-10Fastening the captive nuts.................................................................................................................2-7
Figure 2-11Installing the rack-mounting ears for the ETSI cabinet....................................................................2-7
Figure 2-12Installing the protection grounding cable (using the grounding point at the left side of the chassis)
...............................................................................................................................................................................2-8
Figure 2-13Installing the protection grounding cable (using the grounding point on the left rack-mounting ear of
the chassis)............................................................................................................................................................2-8
Figure 2-14Fastening the chassis........................................................................................................................2-9
Figure 2-15Appearance of the IDU 620 after it is installed in the cabinet..........................................................2-9
Figure 2-16Rack-mounting ears for the ETSI cabinet of the IDU 610.............................................................2-10
Figure 2-17Installing the rack-mounting ears for the ETSI cabinet of the IDU 610 (wall-mounting).............2-11
Figure 2-18Fastening the IDU 610 that has wall-mounting holes on the wall..................................................2-11
Figure 2-19Appearance of the IDU 610 that has wall-mounting holes after it is installed on the wall........ ....2-12
Figure 2-20Installing the rack-mounting ears for the 19-inch cabinet of the IDU 620 (wall-mounting).........2-13
Figure 2-21Fastening the IDU 620 that has wall-mounting holes on the wall..................................................2-14
Figure 2-22Appearance of the IDU 620 that has wall-mounting holes after it is installed on the wall........ ....2-15
Figure 2-23Wall-mounting ears........................................................................................................................2-16
Figure 2-24Installing the wall-mounting ears...................................................................................................2-16
Figure 2-25Fastening the IDU 620 that does not have wall-mounting holes on the wall.................................2-17
OptiX RTN 600 Radio Transmission System
Installation Guide Figures
Issue 06 (2007-12-30) Huawei Technologies Proprietary v
http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://00-3%20about%20this%20document.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-02%20installing%20the%20idu.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://00-3%20about%20this%20document.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
8/168
8/10/2019 OptiX RTN 600 Installation Guide_2
9/168
Figure 5-5Bracket components of a 6 GHz ODU...............................................................................................5-5
Figure 5-6Installing the ODU bracket.................................................................................................................5-5
Figure 5-7Installing the ODU on the pole...........................................................................................................5-6
Figure 5-8Waveguide-to-coaxial converter.........................................................................................................5-6
Figure 5-9RF cable..............................................................................................................................................5-7
Figure 5-10Applying appropriate lubricant to the gasket on the flange interface of the antenna..................... ..5-7
Figure 5-11Installing the RF cable to the waveguide-to-coaxial converter........................................................5-8
Figure 5-12Installing the RF cable to the ODU..................................................................................................5-8
Figure 5-13Bracket components of a 6 GHz ODU...........................................................................................5-10
Figure 5-14Installing the ODU bracket.............................................................................................................5-10
Figure 5-15Installing the ODU on the pole.......................................................................................................5-11
Figure 5-166GHz hybrid coupler.....................................................................................................................5-11
Figure 5-17RF cable..........................................................................................................................................5-12
Figure 5-18Applying appropriate lubricant to the gasket on the flange interface of the antenna............... ......5-12
Figure 5-19Installing the RF cable to the 6 GHz hybrid coupler......................................................................5-13
Figure 5-20Installing the RF cable to the ODU................................................................................................5-14
Figure 6-1Connecting the protection grounding cable to the ODU....................................................................6-2
Figure 6-2Fixing the grounding clip base...........................................................................................................6-3
Figure 6-3Waterproof curves before the IF cable enters the IDU room.............................................................6-4
Figure 6-4Connecting the IF cable to the ODU..................................................................................................6-5
Figure 6-5Waterproof curves under the ODU.....................................................................................................6-5
Figure 6-6Grounding points of the IF cable (the ODU is mounted on a tower).................................................6-8
Figure 6-7Grounding points of the IF cable (the ODU is mounted on the roof-top)..........................................6-9Figure 6-8Stripping the cable sheath.................................................................................................................6-11
Figure 6-9Installing the grounding clips...........................................................................................................6-11
Figure 6-10Direction of the grounding wire of the clip....................................................................................6-11
Figure 6-11Waterproofing the grounding clip..................................................................................................6-11
Figure A-1Stripping back the cable sheath and the insulating layer..................................................................A-1
Figure A-2Fitting the lock nut and the clamp 1.................................................................................................A-2
Figure A-3Fitting the clamp 2............................................................................................................................A-2
Figure A-4Stripping back the insulating layer...................................................................................................A-2
Figure A-5Fitting the connector.........................................................................................................................A-3
Figure A-6Fastening the connector....................................................................................................................A-3
Figure B-1Waterproof insulation tape................................................................................................................B-1
Figure B-2PVC tape...........................................................................................................................................B-2
Figure B-3Appearance of waterproofed outdoor connector...............................................................................B-3
Figure C-1Checking the cable circuit.................................................................................................................C-1
Figure D-1Label for power cables......................................................................................................................D-2
Figure D-2Label for signal cables......................................................................................................................D-3
Figure D-3Writing direction of the label............................................................................................................D-4
Figure D-4Appearance of labels affixed on power cables............................................................... ..................D-5
Figure D-5Affixing labels to signal cables.........................................................................................................D-6
OptiX RTN 600 Radio Transmission System
Installation Guide Figures
Issue 06 (2007-12-30) Huawei Technologies Proprietary vii
http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-c%20checking%20the%20cable%20circuit.pdf/http://02-b%20waterproofing%20outdoor%20connectors.pdf/http://02-b%20waterproofing%20outdoor%20connectors.pdf/http://02-b%20waterproofing%20outdoor%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-c%20checking%20the%20cable%20circuit.pdf/http://02-b%20waterproofing%20outdoor%20connectors.pdf/http://02-b%20waterproofing%20outdoor%20connectors.pdf/http://02-b%20waterproofing%20outdoor%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
10/168
Figure D-6Appearance of labels affixed on signal cables..................................................................................D-6
Figure D-7Example of the label on a power cable.............................................................................................D-7
Figure D-8Example of the label on a fiber that connects two pieces of equipment...........................................D-9
Figure D-9Example of the label on a fiber that connects the equipment and the ODF......................................D-9
Figure D-10Example of the label on a trunk cable that connects two pieces of equipment............................D-11
Figure D-11Example of the label on a trunk cable that connects the equipment and the DDF.......................D-11
Figure D-12Example of the label on an IF jumper...........................................................................................D-12
Figure D-13Example of the label on a network cable......................................................................................D-13
Figure D-14Example of the label on an external alarm cable..........................................................................D-14
Figure E-1Example of the label on the IF cable.................................................................................................E-2
Figure E-2Appearance of the label after it is bound with the IF cable...............................................................E-3
Figures
OptiX RTN 600 Radio Transmission System
Installation Guide
viii Huawei Technologies Proprietary Issue 06 (2007-12-30)
http://02-e%20engineering%20labels%20for%20outdoor%20if%20cables.pdf/http://02-e%20engineering%20labels%20for%20outdoor%20if%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
11/168
Tables
Table 1-1Installation flow................................................................................................................................... 1-2
Table 1-2Tool list................................................................................................................................................ 1-3
Table 1-3Checklist for IDU installation conditions............................................................................................ 1-4
Table 1-4Checklist for ODU installation conditions...........................................................................................1-4
Table 1-5Checklist for the lightning-proof and grounding system..................................................................... 1-5
Table 1-6Checklist for the power system............................................................................................................1-6
Table 1-7Checklist for the auxiliary devices and cables.....................................................................................1-6
Table 6-1Description of grounding the IF cable (the ODU is mounted on a tower)...........................................6-7
Table 6-2Description of grounding the IF cable (the ODU is mounted on the roof-top)....................................6-8
Table 7-1Check items for the cabinet and the IDU.............................................................................................7-2
Table 7-2Check items for the IDU cables...........................................................................................................7-3
Table 7-3Check items for the cabinet power cables and grounding cables.........................................................7-4
Table 7-4Check items for the antenna, hybrid coupler, and ODU......................................................................7-6
Table 7-5Check items for separate mount components.......................................................................................7-6Table 7-6Check items for the ODU cables..........................................................................................................7-7
Table D-1Information on the label affixed to the power cable...........................................................................D-7
Table D-2Information on the label affixed to the fiber that connects two pieces of equipment........................D-8
Table D-3Information on the label affixed to the fiber that connects the equipment and the ODF...................D-8
Table D-4Information on the label affixed to the trunk cable that connects two pieces of equipment............D-10
Table D-5Information on the label affixed to the trunk cable that connects the equipment and the DDF.......D-10
Table D-6Information on the label affixed to the IF jumper............................................................................D-12
Table D-7Information on the label affixed to the network cable.....................................................................D-13
Table D-8Information on the label affixed to the external alarm cable............................................................D-14
Table E-1Information on the label bound to the IF cable...................................................................................E-2
OptiX RTN 600 Radio Transmission System
Installation Guide Tables
Issue 06 (2007-12-30) Huawei Technologies Proprietary ix
http://02-e%20engineering%20labels%20for%20outdoor%20if%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://02-e%20engineering%20labels%20for%20outdoor%20if%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/http://01-01%20before%20you%20start.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
12/168
8/10/2019 OptiX RTN 600 Installation Guide_2
13/168
About This Document
Purpose
This document is an operation guide provided for installation engineers. It describes the
installation flow, methods, and procedures of the OptiX RTN 600, including the IDU installation,
ODU installation, cable installation, and grounding specifications.
Related Versions
The following table lists the product versions related to this document.
Product Name Version
OptiX RTN 600 V100R001
OptiX iManager T2000 V200R005C01
Intended Audience
This document is intended for installation engineers. Before reading this document, you need
to:
l Know engineering installation basics of communication equipment
l Know safety precautions during installation (For details, refer to the OptiX RTN 600 Radio
Transmission System Compliance and Safety Manual.)
Organization
This document is organized as follows.
Chapter Content
1 Before You Start Describes the installation flow and preparations.
OptiX RTN 600 Radio Transmission System
Installation Guide About This Document
Issue 06 (2007-12-30) Huawei Technologies Proprietary 1
http://01-01%20before%20you%20start.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
14/168
Chapter Content
2 Installing the IDU Describes how to install an IDU in different circumstances.
3 Installing IDU
Cables
Describes how to install the IDU cables.
4 Installing the 7
GHz - 38 GHz ODU
Describes how to install the 7 GHz - 38 GHz ODU and its accessories.
5 Installing the 6
GHz ODU
Describes how to install the 6 GHz ODU and its accessories.
6 Installing ODU
Cables
Describes how to install the ODU protection grounding cable and the
IF cable, and how to ground the IF cable.
7 Checking the
Installation
Provides the check items for the installation of the OptiX RTN 600.
A Terminating the
IF Cable with
Connectors
Describes how to terminate the IF cable with connectors.
B Waterproofing
Outdoor
Connectors
Describes how to waterproof outdoor connectors.
C Checking the
Cable Circuit
Describes how to use a multimeter to test the cable circuit.
D Engineering
Labels for IndoorCables
Describes the engineering labels for cables and how to fill and affix
labels.
E Engineering
Labels for Outdoor
IF Cables
Describes the Engineering labels for outdoor IF cables and how to
bind labels.
F Glossary Lists the terms used in this document.
G Acronyms and
Abbreviations
Lists the acronyms and abbreviations used in this document.
Conventions
Symbol Conventions
The symbols that may be found in this document are defined as follows.
About This Document
OptiX RTN 600 Radio Transmission System
Installation Guide
2 Huawei Technologies Proprietary Issue 06 (2007-12-30)
http://01-06%20installing%20odu%20cables.pdf/http://02-g%20acronyms%20and%20abbreviations.pdf/http://02-g%20acronyms%20and%20abbreviations.pdf/http://02-f%20glossary.pdf/http://02-e%20engineering%20labels%20for%20outdoor%20if%20cables.pdf/http://02-e%20engineering%20labels%20for%20outdoor%20if%20cables.pdf/http://02-e%20engineering%20labels%20for%20outdoor%20if%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-d%20engineering%20labels%20for%20indoor%20cables.pdf/http://02-c%20checking%20the%20cable%20circuit.pdf/http://02-c%20checking%20the%20cable%20circuit.pdf/http://02-b%20waterproofing%20outdoor%20connectors.pdf/http://02-b%20waterproofing%20outdoor%20connectors.pdf/http://02-b%20waterproofing%20outdoor%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://02-a%20terminating%20the%20if%20cable%20with%20connectors.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-07%20checking%20the%20installation.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-06%20installing%20odu%20cables.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-05%20installing%20the%206%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-02%20installing%20the%20idu.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
15/168
Symbol Description
DANGER
Indicates a hazard with a high level of risk that, if not avoided,
will result in death or serious injury.
WARNING
Indicates a hazard with a medium or low level of risk which,
if not avoided, could result in minor or moderate injury.
CAUTION
Indicates a potentially hazardous situation that, if not avoided,
could cause equipment damage, data loss, and performance
degradation, or unexpected results.
NOTE Provides additional information to emphasize or supplement
important points of the main text.
TIP Indicates a tip that may help you solve a problem or save your
time.
General Conventions
Convention Description
Times New Roman Normal paragraphs are in Times New Roman.
Boldface Names of files, directories, folders, and users are in boldface.
For example, log in as user root.
Italic Book titles are in italics.
Courier New Terminal display is in Courier New.
Safety Precautions
This section describes parts of the safety precautions. Read and follow these safety precautions
before installing and maintaining the OptiX RTN 600.
CAUTION
Before performing any operation, go through the instructions and precautions carefully to
minimize the possibility of accidents. The Caution, Warning and Danger items in other
documents do not cover all the safety precautions that must be followed. They are only
supplements to the safety precautions for operations as a whole. The personnel in charge of
the installation and maintenance must be trained to learn the proper operating methods and
all safety precautions. Only the trained and qualified personnel can install or maintain the
device.
OptiX RTN 600 Radio Transmission System
Installation Guide About This Document
Issue 06 (2007-12-30) Huawei Technologies Proprietary 3
8/10/2019 OptiX RTN 600 Installation Guide_2
16/168
When operating the device, abide by the local safety regulations. The precautions listed in this
chapter are in compliance with the local safety regulations.
When operating the Huawei device, follow the full precautions and special safety instructions
from Huawei.
The personnel in charge of installation and maintenance must understand the basics of the safety
operations. Only trained and qualified personnel can install or maintain the device.
High Voltage
DANGER
l The high voltage power supply supplies power for the device operation. Direct or indirect
contact (through damp objects) with high voltage and AC mains supply may result in
fatal accident.
l Non-standard and improper high voltage operations can result in fire and electric shock.
Therefore, you must abide by the local rules and regulations when bridging and wiring
AC cables through a certain area. The personnel who perform high voltage operations
must be qualified for performing high voltage and AC operations.
l Do not wear conducting articles, such as watches, chains, bracelets and rings while
performing high voltage operations.
l Switch off the power supply immediately if you find water in the rack or if the rack is damp.
l Make sure that the device is kept away from water when being operated in a damp
environment.
Power Cable
DANGER
l Do not install or remove a live line. Transient contact between the core of the power
cable and the conductor might generate electric arc or spark, which can cause fire or
damage to the human body.
l During high voltage and AC operations, special tools must be used instead of commontools.
l Before installing or removing the power cable, turn off the power switch.
l Before connecting the power cable, make sure that the power cable and label conform to
the requirements of the actual installation.
About This Document
OptiX RTN 600 Radio Transmission System
Installation Guide
4 Huawei Technologies Proprietary Issue 06 (2007-12-30)
8/10/2019 OptiX RTN 600 Installation Guide_2
17/168
8/10/2019 OptiX RTN 600 Installation Guide_2
18/168
8/10/2019 OptiX RTN 600 Installation Guide_2
19/168
l Appliances used for lifting objects must be checked and ensured to be intact before
performing any high-altitude operation.
Hoisting Heavy Objects
DANGER
During hoisting heavy objects, do not stand or walk under the boom or the objects.
Sharp Objects
WARNING
When carrying the device with hands, wear protection gloves to avoid injuries caused by
sharp objects.
IF Cable
WARNING
Before installing or removing the IF cable, turn off the ODU-PWR power switch on the IF
board.
Installing and Removing Boards
CAUTION
l When inserting a board, handle it gently to avoid distorting the pins on the backplane.
l Insert the board along the slot guide. Do not allow the board interfaces to come in contact
with that of another board as this can cause short-circuit or can damage the board.
l When holding a board in hand, do not touch the board circuit, components, connectors,
or the connection slots.
OptiX RTN 600 Radio Transmission System
Installation Guide About This Document
Issue 06 (2007-12-30) Huawei Technologies Proprietary 7
8/10/2019 OptiX RTN 600 Installation Guide_2
20/168
Bundling Signal Cables
CAUTION
Bundle the signal cables separately from the strong current cables or high voltage cables.
The space between two adjacent ties must be at least 150 mm.
Update History
Updates between document versions are cumulative. Therefore, the latest document version
contains all updates made to previous versions.
Updates in Issue 06 (2007-12-30)
Sixth release.
Description of the product new features are added, including:
l Guidelines for installing an IDU chassis with wall-mounting holes
l Guidelines for installing an 6 GHz SP series ODU
Updates in Issue 05 (2007-09-30)
Fifth Release.
2.5 Installingan E1 Panel and 3.5.4 Installing the E1 Cable (from the PO1/PH1 Board to
the E1 Panel)are added according to new features of the product.
Updates in Issue 04 (2007-07-30)
Fourth release.
3.5.5 Installing the Ethernet Service Network Cableand 4.4 Installing the ODU (Separate
Mount)are added according to new features of the product.
Updates in Issue 03 (2007-06-30)
Third release.
Bugs found in the previous version are fixed.
Updates in Issue 02 (2007-03-30)
Second release.
Bugs found in the previous version are fixed.
Updates in Issue 01 (2007-03-15)
Initial release.
About This Document
OptiX RTN 600 Radio Transmission System
Installation Guide
8 Huawei Technologies Proprietary Issue 06 (2007-12-30)
http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-04%20installing%20the%207%20ghz%20-%2038%20ghz%20odu.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-03%20installing%20idu%20cables.pdf/http://01-02%20installing%20the%20idu.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
21/168
ATerminating the IF Cable with ConnectorsTerminating the IF cable with connectors is an important job. Whether connectors are correctly
and standardly made directly affects the performance of the IF cable.
Tools and Instruments
l Two wrenches
l Safe edge knife
l File
Installation Materials
l Installation parts and accessories of the type-N connector
l IF cable
Precautions
This procedure is provided only as an example. Always follow the proper instructions packed
with the connector.
Procedure
Step 1 Use the safe edge knife to strip back the cable sheath of 16 mm.
Figure A-1Stripping back the cable sheath and the insulating layer
OptiX RTN 600 Radio Transmission System
Installation Guide A Terminating the IF Cable with Connectors
Issue 06 (2007-12-30) Huawei Technologies Proprietary A-1
8/10/2019 OptiX RTN 600 Installation Guide_2
22/168
CAUTION
l During the operation, take care not to damage the core wire of the cable.
l f the length of the stripped sheath in Step 1is more than 16 mm, cut the cable wire to
expose only a length of 6 mm.
Step 2 Fit the lock nut and the clamp 1 on the cable.
Figure A-2Fitting the lock nut and the clamp 1
Step 3 Fit the clamp 2.
1. Fold back the braided shield to cover the clamp 1.
2. Tidy the braided shield and then use the clamp 2 to bind the braided shield.
3. Cut the redundant part of the shielding layer.
Figure A-3Fitting the clamp 2
Step 4 Use the safe edge knife to strip back the dielectric insulating layer in front of the clamp 2.
During the operation, the exposed cable wire should be 6 mm long.
Figure A-4Stripping back the insulating layer
NOTE
If the length of the stripped sheath is more than 16 mm, cut the cable wire in Step 4.
Step 5 Use a file to taper the edge of the core wire about 0.5 mm to make the top in an arc shape, andclean out the metal filings.
Step 6 Fit the connector.
A Terminating the IF Cable with Connectors
OptiX RTN 600 Radio Transmission System
Installation Guide
A-2 Huawei Technologies Proprietary Issue 06 (2007-12-30)
8/10/2019 OptiX RTN 600 Installation Guide_2
23/168
Figure A-5Fitting the connector
Step 7 Connect the connector and the lock nut. Use a wrench to tighten the connection.
Use the wrench 1 to rotate the lock nut and the wrench 2 to keep the body of connector standing.
The recommended torque is 152 Nm.
Figure A-6Fastening the connector
----End
Postrequisite
After making the connectors, use the multimeter to check the cable circuit. Only after you make
sure that there is no short circuit or open circuit in the cables can you use the cables.
Related Topics
C Checking the Cable Circuit
OptiX RTN 600 Radio Transmission System
Installation Guide A Terminating the IF Cable with Connectors
Issue 06 (2007-12-30) Huawei Technologies Proprietary A-3
http://02-c%20checking%20the%20cable%20circuit.pdf/8/10/2019 OptiX RTN 600 Installation Guide_2
24/168
8/10/2019 OptiX RTN 600 Installation Guide_2
25/168
BWaterproofing Outdoor ConnectorsAll outdoor IF cable connectors and grounding clips must be strictly waterproofed.
Prerequisite
The outdoor connector or the grounding clip must be installed.
Tools and Instruments
None.
Installation Materials
l Waterproof insulation tape
Figure B-1Waterproof insulation tape
l PVC tape
OptiX RTN 600 Radio Transmission System
Installation Guide B Waterproofing Outdoor Connectors
Issue 06 (2007-12-30) Huawei Technologies Proprietary B-1
8/10/2019 OptiX RTN 600 Installation Guide_2
26/168
Figure B-2PVC tape
Precautions
To facilitate future removal of tapes, first wrap a layer of PVC tape and then wrap the waterproof
insulation tape over the first layer.
Procedure
Step 1 Clean the connector or the grounding clip.
Step 2 Uncoil the waterproof insulation tape.
Step 3 Stick one end of the tape to the IF cable 2 to 5 cm away from the connector or the groundingclip.
The sticky side should face inwards.
Step 4 Stretch the tape until it is 3/41/2 as wide as its original size and always keep this stretchingstrength in the following steps.
Step 5 From the point that is 2 to 5 cm away from the connector or the grounding clip, wrap the cablespirally towards the connector or the grounding clip. Make sure that the overlapping area of
adjacent tape layers is 1/2 of the stretched width.
Step 6 When the tap runs to the point that is 2 or 5 cm away from the connector or the grounding clipat the other side, reverse the wrap direction to let the tape go back to the starting point.
Step 7 When the tape reaches the starting point, reverse the wrap direction to let the tape run to theother ending point.
That is, there are three layers of waterproof insulation tape.
Step 8 After wrapping, squeeze the tape until it sticks to the cable to make sure that no air remainsbetween tape layers.
Step 9 Similarly, wrap three layers of PVC tape over the waterproof insulation tape.
During the wrapping, maintain the stretching strength to keep the width of the PVC tape 3/4
1/2 as wide as the original size.
Step 10 After waterproof processing, use the outdoor bundling strap to bind the PVC tape tight at thepositions 1 cm away from the wrapping edges at both ends, to avoid aging and falling off of the
PVC tape.
----End
B Waterproofing Outdoor Connectors
OptiX RTN 600 Radio Transmission System
Installation Guide
B-2 Huawei Technologies Proprietary Issue 06 (2007-12-30)
8/10/2019 OptiX RTN 600 Installation Guide_2
27/168
Result
Figure B-3Appearance of waterproofed outdoor connector
OptiX RTN 600 Radio Transmission System
Installation Guide B Waterproofing Outdoor Connectors
Issue 06 (2007-12-30) Huawei Technologies Proprietary B-3
8/10/2019 OptiX RTN 600 Installation Guide_2
28/168
8/10/2019 OptiX RTN 600 Installation Guide_2
29/168
CChecking the Cable CircuitDuring the cable routing, bundling and connector installing, there may be short circuits or open
circuits in cables. Hence, it is necessary to test cables after the above-mentioned procedures are
complete. This section describes how to use a multimeter to test a cable with the DB44 connector
at one end and one group of SMB connectors at the other end.
Tools and Instruments
l Multimeter
l Short-circuiting line
Procedure
Step 1 According to the pin assignment of the DB44 connector, use the short-circuiting line to short-circuit two pins that correspond to an SMB connector.
Step 2 Use the multimeter to measure the resistance between the internal and external conductors ofthe SMB connector.
Figure C-1Checking the cable circuit
A
DDF side
R1
IDU side
Short-circuitingpins 23 and 38
OptiX RTN 600 Radio Transmission System
Installation Guide C Checking the Cable Circuit
Issue 06 (2007-12-30) Huawei Technologies Proprietary C-1
8/10/2019 OptiX RTN 600 Installation Guide_2
30/168
The resistance should be zero ohms.
Step 3 Remove the short-circuiting line.
Step 4 Read the multimeter. At this time, the multimeter also measures the resistance between the
internal and external conductors of the SMB connector.The resistance should be infinite.
Step 5 Repeat the above steps to test other core wires of the E1 cable.
----End
C Checking the Cable Circuit
OptiX RTN 600 Radio Transmission System
Installation Guide
C-2 Huawei Technologies Proprietary Issue 06 (2007-12-30)
8/10/2019 OptiX RTN 600 Installation Guide_2
31/168
DEngineering Labels for Indoor CablesEngineering labels for indoor cables should be filled in and affixed in accordance with this
specification, unless the customer has different requirements.
D.1 Introduction to Labels
There are two types of engineering labels, labels for power cables and labels for signal cables.
D.2 Preparing Labels
The label contents can be printed or written on labels. Printing is recommended for the sake of
high efficiency and eye-pleasant layout.
D.3 Affixing Labels
The procedure for affixing a label to a power cable is different from that for affixing a label to
a signal cable.
D.4 CommonEngineering Labels
Common engineering labels include labels for the cabinet power cable, the optical fiber, the
trunk cable, the IF jumper, the network cable, and the external alarm cable. For other unspecified
labels, handlethem according to the onsite requirements.
OptiX RTN 600 Radio Transmission System
Installation Guide D Engineering Labels for Indoor Cables
Issue 06 (2007-12-30) Huawei Technologies Proprietary D-1
8/10/2019 OptiX RTN 600 Installation Guide_2
32/168
D.1 Introduction to Labels
There are two types of engineering labels, labels for power cables and labels for signal cables.
D.1.1 Labels for Power Cables
The label for power cables is rectangular with round corners.
There is a dividing line on the label. In the upper left corner, there is a mark "TO:". The mark
is used to identify the opposite end of the cable on which the label is affixed.
The label is affixed to the identification plate on the cable tie that binds the cable.
Figure D-1Label for power cables
1.5
0.6100
26.2
12.2
0.6
10
11TO:
25
R1.0
Cable tie
Label
Dividing line on the label
Unit: mm
D.1.2 Labels for Signal Cables
The label for signal cables is L-shaped with fixed dimensions.
The short dividing lines on the label help to more clearly specify the position of a cable. On the
label, there is a dotted line that helps to fold the label. In the lower right corner, there is a mark"TO:". The mark is used to identify the opposite end of the cable on which the label is affixed.
D Engineering Labels for Indoor Cables
OptiX RTN 600 Radio Transmission System
Installation Guide
D-2 Huawei Technologies Proprietary Issue 06 (2007-12-30)
8/10/2019 OptiX RTN 600 Installation Guide_2
33/168
Figure D-2Label for signal cables
TO:
84.0
7.5
7.0
5.5
5.5
11.0
11.0
37.0
7.5
7.0
5.5
5.5
1.5
0.6
1.0
2.0
Dividing line
Dotted line
10.0
Dividing line
Dotted line
Unit: mm
D.2 Preparing Labels
The label contents can be printed or written on labels. Printing is recommended for the sake of
high efficiency and eye-pleasant layout.
D.2.1 Printing Labels
To print a label, it is required to use a laser printer to print it according to the label template.
The requirements are as follows:
l Use a laser printer.
l Use the label template.
You can obtain the template by:
Downloading the template from http://support.huawei.com. The directory of the
template is Engineering Service > Engineering Quality > Quality Standard and
Template.
Asking for the template from a local office of Huawei.
l When you modify the information on the template, do not modify the settings of centered
characters, direction, fonts, and others.
l When there are too many characters to be filled in, zoom out the characters.
OptiX RTN 600 Radio Transmission System
Installation Guide D Engineering Labels for Indoor Cables
Issue 06 (2007-12-30) Huawei Technologies Proprietary D-3
8/10/2019 OptiX RTN 600 Installation Guide_2
34/168
8/10/2019 OptiX RTN 600 Installation Guide_2
35/168
After the bundling, all identification plates should face right or upward and all labels should face
outside.
----End
Result
Figure D-4Appearance of labels affixed on power cables
TO:
TO:
B03 -48V2B03
-48V2
1-The identification plate is on top
of the cable in horizontal cabling
2-The identification plate is at the right
side of the cable in vertical cabling
Cable
Cable
D.3.2 Affixing a Label to a Signal Cable
The label for the signal cable is directly affixed to the signal cable.
Prerequisite
l The signal cable must be installed.
l The label content must be filled in.
Procedure
Step 1 Determine the position of the label.
In general, affix the label 2 cm away from the connector. To avoid bending the cable or making
the installation of other cables inconvenient, you can affix the label to other places.
Step 2 Remove a label from the paper.
Step 3 Affix the label to the cable.
After the bundling, all labels should face right or upward.
OptiX RTN 600 Radio Transmission System
Installation Guide D Engineering Labels for Indoor Cables
Issue 06 (2007-12-30) Huawei Technologies Proprietary D-5
8/10/2019 OptiX RTN 600 Installation Guide_2
36/168
Figure D-5Affixing labels to signal cables
Stick side
Cable
TO:1 B02 1 5 05Part
Cable Cable
----End
Result
Figure D-6Appearance of labels affixed on signal cables
TO:
1
A01
2
A
06
TO:
1 A01 2 A 06
D.4 Common Engineering Labels
Common engineering labels include labels for the cabinet power cable, the optical fiber, the
trunk cable, the IF jumper, the network cable, and the external alarm cable. For other unspecified
labels, handle them according to the onsite requirements.
D.4.1 Engineering Labels for Cabinet Power Cables
These labels are affixed to the power cable, the grounding cable (BGND), and the protection
grounding cable (PGND) of a cabinet. Affix the labels to both ends of the cable.
D Engineering Labels for Indoor Cables
OptiX RTN 600 Radio Transmission System
Installation Guide
D-6 Huawei Technologies Proprietary Issue 06 (2007-12-30)
8/10/2019 OptiX RTN 600 Installation Guide_2
37/168
Label Content
Table D-1Information on the label affixed to the power cable
Content Meaning MN(BC) - -48V1 At the side of the loaded cabinet, MN identifies the row number and
column number of the power distribution equipment. BC identifies
the row number and column number of the 48 V connector (if there
is no row number or column number, or the connector can be
identified without them, BC can be omitted). Write BC just under
MN. BGND and PGND have no row number or column number for
identification.
At the side of the power distribution cabinet: Only MN is used to
identify the cabinet.
MN(BC) - -48V2
MN(BC) - BGND
MN(BC) - PGND
NOTE
The above table lists the cable content of two 48 V power supplies. For other DC voltages, the label
contents are similar.
Example
Figure D-7Example of the label on a power cable
TO:
A01 -48V2 B08
TO:
B03 -48V2
Label on the loaded cabinet side Label on the power distribution cabinet side
At the side of the loaded cabinet, the label marked with "A01/B08-48V2" on the cable indicates
that the cable supplies 48 V2 power, which is from the eighth connector on the second row of
48 V bus bar in the cabinet on Row A, Column 1 in the equipment room.
At the side of the power distribution cabinet, the label marked with "B03-48V2" on the cableindicates that the cable supplies 48 V2 power, which is from the loaded cabinet on Row B,
Column 03 in the equipment room.
D.4.2 Engineering Labels for Optical Fibers
There are two types of labels for optical fibers. One type is used for the optical fiber that connects
two pieces of equipment. The other type is used for the optical fiber that connects the equipment
and the ODF. The labels of both types should be affixed to both ends of a fiber.
OptiX RTN 600 Radio Transmission System
Installation Guide D Engineering Labels for Indoor Cables
Issue 06 (2007-12-30) Huawei Technologies Proprietary D-7
8/10/2019 OptiX RTN 600 Installation Guide_2
38/168
Label Content
Table D-2Information on the label affixed to the fiber that connects two pieces of equipment
Content Parameter Meaning
MN-B-C-D-R/T MN: cabinet number M: row number of a cabinet, from A to Z
N: column number of a cabinet, from 01
to 99
B: subrack number Numbered from down upwards with two
digits
C: physical slot number Numbered with two digits
D: optical interface number Numbered from top downwards and
from left to right with two digits
R: optical receiving interface
T: optical transmitting
interface
MN-B-C-D-R/T MN: cabinet number The meanings are the same as above.
When the local equipment and the
opposite equipment are not in the same
equipment room, MN can be the name of
the equipment room.
B: subrack number
C: physical slot number
D: optical interface number
R: optical receiving interfaceT: optical transmitting
interface
Table D-3Information on the label affixed to the fiber that connects the equipment and the ODF
Content Parameter Meaning
MN-B-C-D-R/T MN: cabinet number M: row number of a cabinet, from A to Z
N: column number of a cabinet, from 01
to 99
B: subrack number Numbered from down upwards with two
digits
C: physical slot number Numbered with two digits
D: optical interface number Numbered from top downwards and
from left to right with two digits
R: optical receiving interface
T: optical transmitting
interface
D Engineering Labels for Indoor Cables
OptiX RTN 600 Radio Transmission System
Installation Guide
D-8 Huawei Technologies Proprietary Issue 06 (2007-12-30)
8/10/2019 OptiX RTN 600 Installation Guide_2
39/168
Content Parameter Meaning
ODF-MN-B-C-
R/T
MN: row number and column
number of the ODF
M: row number of the ODF, from A to Z
N: column number of the ODF, from 01
to 99
B: row number of the terminal Numbered with two digits
C: column number of the
terminal
R: optical receiving interface
T: optical transmitting
interface
Example
Figure D-8Example of the label on a fiber that connects two pieces of equipment
TO:
01 05 05 R
G01010101T
A01
"A0-01-05-05-R" indicates that the local end of the fiber is connected to the optical receivinginterface 05 on Slot 5, Subrack 01 in the cabinet on Row A, Column 01 in the equipment room.
"G01-01-01-01-T" indicates that the opposite end of the fiber is connected to the optical
transmitting interface 01 on Slot 01, Subrack 01 in the cabinet on Row G, Column 01 in the
equipment room.
Figure D-9Example of the label on a fiber that connects the equipment and the ODF
TO:
G01 01 01 R
A01010505R
ODF
"ODF-G01-01-01-R" indicates that the local end of the fiber is connected to the optical receiving
terminal on Row 01, Column 01 of the ODF on Row G, Column 01 in t