DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 1 of 16
NCDOI OSFM Evaluation Services
Scope of DOI White Paper: The Purpose of this document is to provide clarification on North Carolina
State Code requirements to Code Officials (CEO) who are agents for the Authority Having Jurisdiction
(AHJ).
DOI File Number: WP-009-11
Edition Date: May 10, 2011
Revision Date: September 21, 2012
Subject of White Paper: Code Considerations for Constructing a Covered Outdoor
Space Adjacent to an Existing Restaurant, Bar or Nightclub
TABLE OF CONTENTS:
1.0 INTENT………………………………………………………………………………………....2
2.0 NORTH CAROLINA CODE REFERENCES…………………………………………………3
3.0 CODE DEFINITIONS………………………………………………………………………….3
4.0 CODE CONSIDERATIONS……………………………………………………………………4
5.0 INFORMATION REQUIRED FOR PROJECT REVIEW BEFORE ISSUING PERMIT……5
Occupancy Classification…………………………………...…………………………………5 A.
Occupant Load………………………………………………………………………………...6 B.
Construction Type……………………………………………………………………………..8 C.
Area and Height………………………………………………………………………………..9 D.
Building Aggregate Area, Stories or Height Exceeds NCBC Table 503……………………..10 E.
Non-Separated” or “Separated” Occupancies in a Mixed Occupancy………………………..10 F.
Fire Suppression System Considerations….…………………………………………………..12 G.
Plumbing Fixtures……………………………………………………………………………..13 H.
Energy Requirements………………………………………………………………………….14 I.
Pliable Light Transmitting or Fabric Curtain System for Weather Protection……….………15 J.
Guard Rails……………………………………………………………………………………15 K.
Structural Requirements………………………………………………………………………15 L.
Accessibility Requirements.......................................................................................................15 M.
Maintaining Means of Egress in Existing Building During Construction................................15 N.
6.0 REFERENCES…………………………………………………………………………………16
7.0 PHOTO RESOURCES…………………………………………………………………………16
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 2 of 16
1.0 INTENT
This Document addresses 2012 North A.
Carolina State Building Codes
(NCSBC) requirements where a
permanent or a seasonal roof structure
will be constructed over an outdoor
space (for example, a patio, deck,
balcony, etc.) that is adjacent and
physically attached to an existing
building. The commercial establishment
in the existing building is primarily
intended for the consumption of food
and/or alcoholic beverages and the new
covered outdoor space will serve the
same function. The structural framing
over the outdoor space may support a
solid covering (i.e., metal, shingles,
fabrics, light transmitting plastic panels,
flexible coverings like canvas, etc.-
Figures 1 & 2) or a semi-solid/opened
covering (i.e., structural framing
supporting lattice work, grating/trellis,
etc.- Figure 3).
These establishment types include, but B.
are not limited to, banquet halls,
nightclubs, restaurants, taverns and/or
bars and are usually classified by
occupancy in the NCBC as either a
Business (Group B) or an Assembly
(Group A-2), depending on their
calculated aggregate design occupant
load.
The establishment may be located in a C.
single occupancy use building or may
be a tenant space in a multi-tenant
building with multiple non-separated or
separated occupancy uses. This
document assumes that the new covered
outdoor space is located on the level of
exit discharge and is not separated from
the existing building by a fire wall
(NCBC-706).
This document is not applicable to D.
awnings and canopies as addressed in
Section 3105 of the North Carolina
Building (NCBC).
Figure 1 - Retractable light transmitting fiberglass
enclosure supported by aluminum frame.
Figure 2 - Plastic enclosure supported by steel
frame.
Figure 1 – Wood lattice supported by wood structural
frame.
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 3 of 16
NORTH CAROLINA CODE REFERENCES* 2.0
North Carolina Building Code (NCBC) A.
North Carolina Fire Prevention Code (NCFPC) B.
North Carolina Energy Code (NCEC) C.
North Carolina Plumbing Code (NCPC) D.
* Unless specifically noted otherwise, all code references are the 2012 edition
CODE DEFINITIONS 3.0
Assembly Group A-2 Occupancies (NCBC-Section 303): Assembly uses intended for food A.
and/or drink consumption including, but not limited to (1) banquet halls, (2) night clubs, (3)
restaurants and (4) taverns and bars. Note that Exception # 1 under Section 303.1 states that
“A building or tenant space used for assembly purposes with an occupant load of less than 50
persons shall be classified as Group B occupancy.” (See 5.0-A of this document for additional
information on occupancy classification and 5.0-B on calculating the design occupant load).
Business Group B Occupancies (NCBC-Section 304): Business Group B occupancies include, B.
among others, the use of a building or structure, or a portion thereof, for office, professional
or service-type transactions, including storage of records and accounts. NCBC-304.1 lists
examples of business occupancies.
AREA, BUILDING (NCBC-Section 502): The area included within surrounding exterior C.
walls (or exterior walls and fire walls) exclusive of vent shafts and courts. Areas of the
building not provided with surrounding walls shall be included in the building area if such
areas are included within the horizontal projection of the roof or floor above.
FIRE SEPARATION DISTANCE (NCBC-Section 702): The distance measured from the D.
building face to one of the following: (1) the closest interior lot line; (2) to the centerline of a
street, an alley or public way; or (3) to an imaginary line between two buildings on the
property. The distance shall be measured at right angles from the face of the wall. Refer to
NCBC-Table 602 for fire-resistance rating requirements for exterior walls based on fire
separation distance.
FIRE AREA (NCBC-Section 902): The aggregate floor area enclosed and bounded by fire E.
walls, fire barriers, exterior walls, or horizontal assemblies of a building. Areas of the
building not provided with surrounding walls shall be included in the fire area if such areas
are included within the horizontal projections of the roof or floor next above.
FIRE BARRIER (NCBC-Section 702): A fire-resistant-rated wall assembly of materials F.
designed to restrict the spread of fire in which continuity is maintained. Fire barrier
requirements are addressed in NCBC-Section 707. Note that a fire barrier provides a higher
degree of protection than a fire partition (NCBC-Section 709), but lacks the inherent structural
integrity of a fire wall (NCBC-Section 706). Fire barrier assemblies must be continuous from
the top of a fire-resistance-rated floor/ceiling assembly to the underside of the floor or roof
slab or deck above. The barrier must be constructed tight and securely attached to the
underside of the floor slab or roof deck.
FIRE PARTITION (NCBC-Section 702): A vertical assembly of materials designed to restrict G.
the spread of fire in which openings are protected. Fire partition requirements are addressed in
NCBC-Section 709.
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 4 of 16
Figure 4-After the construction of a covered outdoor space
(beyond), existing exit(s) shall continue to be code
compliant.
FIRE WALL (NCBC-Section 702): A fire-resistant-rated wall having protected openings, H.
which resist the spread of fire and extends continuously from the foundation to or through the
roof, with sufficient structural stability under fire conditions to allow collapse of construction
on either side without collapse of the wall. Fire wall requirements are addressed in NCBC-
Section 706).
FLOOR AREA, GROSS (NCBC-Section 1002): The floor area within the inside perimeter of I.
the exterior walls of the building under consideration, exclusive of vent shafts and courts,
without deduction for corridors, stairways, closets, the thickness of interior walls, columns or
other features. The floor area of a building, or portion thereof, not provided with surrounding
exterior walls shall be the usable area under the horizontal projection of the roof or floor
above. The gross floor area shall not include shafts with no openings or interior courts.
FLOOR AREA, NET (NCBC-Section 1002): The actual occupied area not including J.
unoccupied accessory areas such as corridors, stairways, toilet rooms, mechanical rooms and
closets.
HORIZONTAL ASSEMBLY (NCBC-Section 702): A fire-resistant-rated floor or roof K.
assembly of materials designed to restrict the spread of fire in which continuity is maintained.
Horizontal assembly requirements are addressed in NCBC-Section 712.
CODE CONSIDERATIONS 4.0
For purposes of this document, it is assumed A.
that the existing building complied with all
N.C. State Building Codes in effect at the time
the structure was permitted by the Authority
Having Jurisdiction (AHJ). However, the CEO
needs to confirm that any elements of the
existing building, which may be affected by
the addition of a covered outdoor space, will
continue to comply with code. These elements
include consistent construction type, exiting,
and/or other code items that may also have
been altered after the original Certificate of
Occupancy was issued for the existing
building. For these reasons, it is recommended
that an Appendix B (Building Code Summary
for All Commercial Buildings), with
information on the construction of the
proposed covered outdoor space, also include
information on the existing building on which
the covered outdoor space will be attached.
(Figure 4).
As a resource, hard copies of former North B.
Carolina Code editions are available for use at the DOI-OSFM Engineering Office, located on
the second floor at 322 Chapanoke Road, Raleigh, NC 27603. Some former Codes can also be
found on the DOI-OSFM web site under “STATE BUILDING CODES” at the following link:
http://www.ncdoi.com/OSFM/Engineering/engineering_home.asp
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 5 of 16
Note to Fire Inspectors - It is not C.uncommon for a covered outdoor
space addition to have been
constructed without a required permit
or altered after the original Certificate
of Occupancy was issued. It is
incumbent upon the Fire Inspector to
not assume that the type of
construction and means of egress
condition(s), etc., as currently exist, are
code compliant. (Figure 5).
INFORMATION REQUIRED FOR 5.0
PROJECT REVIEW BEFORE
ISSUING A PERMIT - The CEO’s
review of the submittal requires basic
project information for both the existing
building as well as the addition of the
proposed covered outdoor space. The following data should be addressed on Appendix B and
included as a part of the submittal package:
Occupancy Classification of the Existing Building and the Covered Addition - Determining A.
the occupancy classification, or classifications, of an existing building and the proposed
addition is essential to the correct application of subsequent requirements found throughout
the North Carolina State Building Codes. Use and Occupancy Classifications are addressed in
Chapter 3 of the NCBC. 5.0-B of this document addresses how to calculate the design
occupant load for a covered outdoor addition to an existing building.
1. A single use building has one occupancy group classification. For the purpose of this
White Paper, a restaurant, bar, tavern and/or nightclub are classified by use as either
Assembly-Group A-2 or Business-Group B, based on the calculated design occupant load.
An existing establishment, including a covered outdoor addition, is classified by
occupancy use as Assembly-Group A-2 with a calculated design occupant load of more
than 50 persons. Conversely, an existing establishment, including a covered outdoor
addition, is classified by occupancy use as Business-Group B with a calculated design
occupant load of less than 50 persons
per Exception # 1 under NCBC-
Section 303.1.
2. A multiple tenant building may have
one occupancy classification (for
example, all office tenants-Group B)
or may have more than one
occupancy group use and is
identified by the NCBC as “mixed
occupancy”, per NCBC-Section 508.
(Figure 6).
Example of several occupancy
groups that could be found in a
multi-tenant (mixed occupancy)
Figure 5- All components of means of egress shall be code
compliant. For example, table & chairs under the covered outdoor
space shall not interfere with the path of exit access to the exit of
the building in the background.
Figure 6- Example of a multiple tenant building.
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 6 of 16
building could be a dentist, law firm, or barber shop, etc. (classified as Business-
Group B), a grocery store, or drug store (classified as Mercantile-Group M) and a
restaurant/bar (which could be classified as either Assembly-Group A-2 or Business-
Group B, depending on the calculated design occupant load).
3. Design options for addressing mixed use and occupancy in a building are as follows*:
a. Option # 1- Non-separated uses, where the height, area and sprinkler requirements
for the most restrictive type of occupancy group are applied to the entire building
(refer to NCBC-Section 508.3 and 5.0-F.1 of this document which addresses non-
separated occupancy uses);
b. OR Option # 2 - Separated uses, where individual occupancies are separated by rated
fire barriers. The rated fire barriers are compliance with area limitations determined
by a unit formula and where no occupancy may occur on a floor higher than the
limitation for the individual occupancy and where sprinkler requirements are limited
to the fire area in which the occupancy occurs (refer to NCBC-Section 508.4 and
5.0-F.2 of this document which addresses separated occupancy uses);
c. OR Option # 3 - Combination of non-separated and separated uses;
d. OR Option # 4 - Create separate buildings by separation of one or all of the
occupancies with a fire wall (refer to NCBC-Section 706, which addresses fire
walls).
*NOTE: Each design option, when the NCBC is applied correctly, should provide a
building with an acceptable level of safety. The owner or his designer, not the CEO, is
responsible for determining which option to use and this option is required to be noted on
Appendix B of the drawings. It is the responsibility of the CEO to confirm that the
selected option is designed in a code compliant manner.
Occupant Load of the Existing Building and the Covered Addition - The addition of a covered B.
outdoor space to an existing restaurant, bar, tavern and/or nightclub usually increases the
design occupant load of the entire establishment.
1. Considerations: The purpose for calculating the design occupant load is to establish the
maximum number of persons who occupy a building or a space at any one time. The
maximum square feet per person is based on the use (NCBC-Chapter 3) of each space or
room in accordance with NCBC-Table 1004.1.1, and not the occupancy classification of
the building.
• Example: A restaurant/bar with an aggregate occupant load of less than 50 persons is
classified by occupancy as Group B (Exception #1 under NCBC-Section 303.1) for
purposes other than code exiting requirements. However, the occupant load is not to be
calculated at 100 sq. ft. gross per person as would be allowed for a Business use in
NCBC-Table 1004.1.1. To determine the occupant load in a restaurant or bar, each space
is calculated in accordance to its function. The dance floor, waiting area and bar will be
calculated at 7 sq. ft. net/person (Assembly concentrated without fixed seats). The
seating/dining area will be calculated at 15 sq. ft. net/person (Assembly un-concentrated).
Other spaces will be calculated per person by use in the same manner, i.e., the kitchen at
200 sq. ft. gross/person, the storage room(s) and/or mechanical room at 300 sq. ft.
gross/person, the office(s) at 100 sq. ft. gross/person, etc. Once each space is calculated
individually, the load for all spaces is added together to become the aggregate design
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 7 of 16
occupant load for the entire restaurant or bar. If the load equals or exceeds 50 persons,
the restaurant or bar will be classified as Assembly Occupancy for all code purposes.
2. Importance of correct occupant load
calculations: The calculated design
occupant load determines whether an
establishment (restaurant, bar, etc.),
primarily in the business of serving food
and /or alcoholic drinks for consumption
on the premises, is classified by
occupancy as Group B or Group A in
Chapter 3 of the NCBC. (Figure 7). An
increase in the design occupant load
could also trigger additional means of
egress elements and/or fire protection
systems. Under current code, the load
threshold for occupancy classification as
Business verses Assembly for a
restaurant may have changed from a
previous code:
a. For instance, the 1994 Building Code (with 1996/1997/1998/1999 Amendments), per
Section 304.2.2, defined an establishment such as restaurant/bar/night club (used for
assembly purposes) with less than 100 occupants to be classified by occupancy as
Group B. Group A occupancy was defined as having 100 or more occupants.
b. Per Section 303.1-Exception # 1 of the 2012 NCBC code, an establishment such a
restaurant/bar/night club (used for assembly purposes) with less than 50 occupants in
a building or a tenant space (in a multi-tenant building) can be classified as Business-
Group B. With 50 or more persons, it is classified by occupancy as Assembly-Group
A-2.
• Example: A restaurant with an occupant load of 60 persons would have been
allowed under the 1994 NCBC as Business (Group B), since it had a calculated
design load of less than 100 occupants. With the addition of a covered outdoor area
having a calculated design load of 30 persons, the aggregate occupancy design load is
now 90 persons. Although this establishment, under the 1994 NCBC, would have
continued to be classified as Business occupancy, current code requires that it now be
classified as Assembly (Group A-2) because it has more than 50 occupants.
3. Uncovered outdoor area: The construction of an uncovered outdoor area (patio, deck,
porch, balcony, etc.) directly adjacent to an existing building or tenant space may not
increase the occupant load of the existing building for the purpose of calculating means of
egress, even when the intended use of the outdoor area is to serve the same function as the
existing establishment.
Exception: The means of egress from the uncovered outdoor area does not discharge
directly to the public way by Code compliant means and the occupants are thus
required to return into, and egress through, the adjacent existing building to reach a
code compliant exit. In this scenario, the design occupancy load of the uncovered
outdoor area is now added to the design occupancy load of the existing establishment
for compliance with means of egress requirements as addressed in the NCBC-Section
Figure 7: Covered outdoor dining space, exceeding 50
occupants, is classified by use as A-2. If the door (in the
rear) is an exit leading to the exit discharge, it shall be
marked with an exit sign. Means of egress illumination
shall be provided in this covered outdoor space.
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 8 of 16
1004.8. Calculating the occupant load, based on the type of use for the outdoor area
and for all spaces in the existing building, is required to be in accordance with current
code requirements.
Construction Type of the Existing Building and the Covered Addition - Correct classification C.
of a building by construction type is essential for determining code compliance with respect to
its occupancy classification. Type of construction also relates to the contribution of the
structure itself to fuel load, the potential for spread of fire to adjacent structures and the effort
required by the fire department to fight the fire. In accordance with Chapter 6 of the NCBC, it
is necessary to know the construction type of the proposed covered outdoor space and the
construction type of the existing building, particularly if they are not classified as the same
type of construction (Figure 8). The following are considerations when reviewing for the
correct construction classification:
1. Types of Construction: Each structure must be
assigned a construction classifications, i.e.,
Type I-A, I-B, II-A, II-B, III-A, III-B, IV, V-
A or V-B (NCBC-Section 602) and as
follows:
a. NCBC-Table 601: Based on the
construction classification, structural
members may be required to have a fire-
resistance rating in accordance with
NCBC-Table 601 (Fire-Resistive Rating
Requirements for Building Elements).
b. NCBC-Table 602: Exterior wall
construction of the structure must comply
with the requirements in Table 602 (Fire-
Resistive Rating Requirements for
Exterior Walls Based on Fire Separation
Distance).
2. Existing and Covered Addition Same
Construction Type: If the covered outdoor
space and the existing building are the same
construction and fire-resistance (or non-fire-
resistance) rating type, then the project will be
reviewed as that type of construction for
compliance under NCBC-Tables 503, 601,602
and other code requirements as applicable.
3. Different Construction Types: Where two (or more) types of construction, even if
separated by a fire barrier but not separated by a fire wall, occur in the same building, the
most restrictive construction type shall determine the construction classification type of
the entire building and shall not exceed any of the component limitations in NCBC-Table
503 and Table 602.
Example: If an existing building, classified as A-2 occupancy, is Type II-B
construction and the proposed covered outdoor space is to be Type V-B construction,
then the existing building shall be re-classified as Type V-B unless a fire wall is
constructed between the addition and the existing building. 5.0-E.3 in this document
Figure 8. The construction type of the proposed
covered outdoor space and the construction type
of the existing building should be confirmed.
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 9 of 16
addresses fire walls.
4. Recommendation to CEOs is that a site plan be submitted for review of the following:
a. Compliance with NCBC-Table 602. (Refer to code definition of Fire Separation
Distance in 4.0-D of this document). If the separation distance between the existing
building (with the proposed covered outdoor addition) and any adjacent existing
building(s) on the same property is less than 60 feet apart from the proposed covered
outdoor addition, the construction and occupancy classification of the adjacent
building(s) should also to be provided.
b. Confirmation that the dedicated fire apparatus access, as required in the 2012 NC
Fire Prevention Code-Section 503, will continue to be maintained after construction
of the proposed covered outdoor space.
Area and Height of the Existing Building and the Covered Addition D.
1. Importance of NCBC-Tables 503 and 601:
a. The provisions for governing the height and area of the building based on occupancy
group classification and type of construction are established in NCBC-Section 503.
This Section also establishes NCBC-Table 503 as the primary tool for determining
the minimum type of construction. NCBC-Table 601 is used with NCBC-Table 503
to determine acceptable risk and safety levels of a building and the materials used to
construct it in relationship to fire hazard.
b. In accordance with the descriptions in Chapter 3, classification by occupancy can be
considered as establishing the level of “risk” associated with the occupancy use of a
building. Use of the building is an indication of its fire loading. The various
construction types, described in Chapter 6 and Table 601 of the NCBC, can be
thought of as reflecting various levels of safety provided by fire resistance. NCBC-
Table 503 becomes a risk/safety matrix that sets a minimum level of safety
(construction type) in accordance with the risk (occupancy classification reflecting
internal fire loading). Refer to footnote “a” for general exceptions when reviewing
NCBC-Table 503.
2. Contribution of an Un-covered Outdoor
Area (Patio, Deck, Balcony, etc.) to
Building Area: None
3. Contribution of new Covered Outdoor
Area to existing Building Area (Refer to
the code definition of Area, Building in
3.0-C of this document):
a. When a permanent or temporary roof
structure is constructed over an
outdoor area that is adjacent and is
physically attached to an existing
building, the square foot area under
the covered outdoor space is to be
added to, and included in, the square
footage of the existing building to
calculate the revised aggregate
building area (Figure 9).
Figure 9- The square footage of the covered outdoor space
in the foreground shall be included in the aggregate square
footage of the attached building in the background.
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 10 of 16
b. When a permanent or temporary roof structure is constructed over an outdoor area
that is adjacent and is physically attached to a tenant space in a multi-tenant building
where the other tenant spaces in the remaining building are non-separated (see 5.0-
F.1 of this Document), the area under the covered outdoor space is to be added to,
and included in, the square footage of all tenant spaces to calculate the aggregate
building area. (See 5.0-E.1 of this document where aggregate area, stories, and/or
height exceeds NCBC-Table 503).
Building Aggregate Area, Stories, and/or Height Exceeds NCBC-Table 503: Based on the E.
construction type, if the existing building with the proposed outdoor covered space exceeds
any of the limitations in NCBC-Table 503, the addition is not allowed by the NCBC without
triggering further life safety components. Some examples of possible life safety components
are as following:
1. An NFPA 13 sprinkler system, as addressed in NCBC-Section 506.3, can be provided to
increase the allowable area (or height). The system must be installed throughout the entire
building, including the existing building and the covered outdoor space. If the existing
building is a multi-tenant building with multiple non-separate tenant spaces (see 5.0-F.1
of this Document), a sprinkler system is required in all other non-separated tenant spaces.
2. Construction of a fire wall* between the addition and the existing building divides a
single building into (two) separate buildings, as addressed in NCBC-706. The result is
that all provisions of the code, including area and height & story limitations, fire
protection systems, and means of egress components, are applied individually to the
building on each side of the fire wall (refer to the code definition of Fire Wall in 3.0-H of
this document).
* NOTE: Not fire barrier (NCBC-707) or fire partition (NCBC-709)
3. Modify the level of construction protection, based on fire-resistance rating requirements
for building elements in NCBC-Table 601, to increase the building area and/or height for
compliance with NCBC-Table 503.
Determining if a Building Qualifies as “Non-Separated” or “Separated” Occupancies in a F.
Mixed Occupancy Multiple Tenant Building - A building, usually with multiple tenant spaces
that are classified with more than one occupancy group type use, can be designed as either
non-separated or separated occupancies.
1. Non-Separated Occupancies: Buildings with multiple tenant mixed occupancy uses, not
separated by fire barriers, are considered non-separated occupancies and must comply
with NCBC-508.3. Suppose a proposed covered outdoor area is to be constructed adjacent
to and serve an existing restaurant in a non-separated mixed occupancy multiple tenant
retail building. To confirm that the entire building will continue to qualify as non-
separated occupancies after the covered outdoor area is constructed, the following steps
are be applied to determine that it does not exceed any of the NCBC limitation
requirements in Section 503 and Table 503 (including associated footnotes under Table
503):
a. Determine the occupancy classification for the existing restaurant with the proposed
covered outdoor space and for each individual tenant space in the existing building
(NCBC-Chapter 3). Section 5.0-A of this document addresses occupancy
classification.
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 11 of 16
b. Determine which construction type or types apply to the covered outdoor space and
to each individual tenant space in the existing building (NCBC chapter 6). The
requirements for the most restrictive type of construction are be applied to the entire
structure. For example, if a portion of the building is Type II-A and the remaining
area is Type V-B, the entire building is classified as Type V-B. 5.0-C of this
document addresses construction classification.
c. Calculate the building area, the general building height, and the number of stories (if
more than one story) from the dimensions and building elevations on the drawings.
Obtain the base area and height limitations from NCBC-Table 503. Also review
Chapter 5 for exceptions to these requirements including any increases that can be
obtained, for example, in area or height. Apply any applicable height and area
increases to the base limitations in Table 503 and compare the modified limitations to
the calculated height and area. 5.0-D of this document addresses building area and
height.
d. Apply all other Code requirements to each occupancy group, individually based on
the specific occupancy type of each space. Examples include means of egress
elements (NCBC-Chapter 10), exterior wall requirements (NCBC-Table 602), etc.
2. Separated Occupancies: A multiple tenant building with mixed occupancy types can be
classified as separated occupancies if compliant with NCBC-Section 508.4. Suppose a
proposed covered outdoor area is to be constructed adjacent to and serve an existing
restaurant in an existing separated mixed occupancy multiple tenant retail building. . To
confirm that the entire building will continue to qualify as separated occupancies after
the covered outdoor area is constructed, the following steps are be applied to determine
that it does not exceed any of the NCBC limitation requirements in Section 503 and Table
503 (including associated footnotes under Table 503):
a. In accordance with Chapter 3 of the NCBC, determine which occupancy
classification applies to the covered outdoor space and to each tenant space in the
existing building. Section 5.0-A of this document addresses occupancy classification.
b. Determine where fire barrier(s) separate occupancies or area(s) in the existing
building. NCBC-Section 707 addresses separation requirements by vertically
constructed fire barriers. If more than one story, separation between floors by may be
required between floor(s) by horizontal assemblies, as addressed in NCBC-Section
712. Determine the fire-resistance rating of the fire barriers and, if applicable,
horizontal assemblies. Prescribed ratings shall be as required in NCBC-Table 508.4,
including associated footnotes in this Table.
c. The type of construction for the entire building is determined by the height and area
of the building for each occupancy classification in accordance with NCBC-Chapter
5 and NCBC-Table 503 (including footnotes in this Table) as follows:
Compare the height, relative to the grade plain, of each fire area with respect to the
most restrictive occupancy contained within that fire area to the height allowed by
NCBC-Table 503 for a building in that occupancy type. Also refer to NCBC-Section
504 for exceptions to the height limitations of Table 503 for certain buildings, based
on the building’s proposed occupancy classification and the fire safety features
included in the design of the building.
Determine the weighted average of areas occupied by the various occupancies in
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 12 of 16
Figure 10- Existing building with sprinkler system triggers covered
outdoor space addition to also have compliant sprinkler system.
each fire area. For each story, the area of the occupancy shall be such that the sum of
the ratios of the actual floor area of each occupancy type use, divided by the
allowable floor for each occupancy type use per NCBC-Table 503, shall not exceed
one (1), as addressed in NCBC Section 508.4.2. The area calculation formula for
determining the allowable areas for each occupancy group is as follows:
Actual Area of Actual Area of
Occupancy Type A + Occupancy Type B = < 1
Allowable Area for A Allowable Area for B
Per NCBC-Table 503* per NCBC-Table 503*
*NOTE: The following addresses allowable area:
In the evaluation of allowable area, intervening fire barriers between different fire
areas containing the same occupancy type are not a consideration. In determining
the floor area per occupancy, all fire areas of the same group are added together.
In determining the allowable areas for each occupancy group, the tabular areas
from Table 503 can be modified in accordance with the provisions of NCBC-
Section 506. Thus, the allowable areas are intended to include the increases
obtained as result of sprinklers and frontage. Respective to the allowable
frontage increase, use the entire building perimeter and not just the fire area
perimeter. If considering the sprinkler increase, note that the entire building must
be fully sprinklered per Section 506.3, and not just a particular fire area.
Fire Suppression System Considerations for a Proposed Outdoor Covered Addition to an G.
Existing Building
1. Based on the Code in effect
at the time the existing
building was permitted, fire
suppression systems may not
have been required.
However, the construction
of a roof structure over an
outdoor space adjacent to
and serving the same use as
a restaurant or nightclub
may trigger the requirement
for a sprinkler system
throughout all new and
existing spaces of the
building that are not
separated by fire barriers or
separated by a fire wall.
(Figure 10).
2. A review of NCBC-Chapter
9 is recommended as fire
suppression systems may
now be necessary for Code
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 13 of 16
compliance. Threshold requirements for those systems can be triggered by occupancy
classification, occupancy load, square foot area, and/or level of exit discharge. Current
Code (NCBC-903.2.1.2 and NCFPC-903.2.1.2) requires an NFPA 13 automatic sprinkler
system for A-2 occupancies where one of the following conditions exists:
The fire area exceeds 5000 square feet;
OR The fire area has an occupant load of 300 or more, except 100 or more for
nightclubs*;
OR The fire area is located on a floor other that the level of exit discharge.
*NOTE: For additional information, refer to the White Paper by Evaluation Services
Section entitled “Sprinkler Requirements for Nightclubs Nov 2010” that is located on
the NCDOI-OSFM website at the following link:
http://www.ncdoi.com/OSFM/Engineering/engineering_wpt.asp
3. Example- A new outdoor covered dining area is to be constructed adjacent to and serve an
existing one story restaurant. The finish floor for each is on the level of exit discharge and
the construction type for both structures is V-B:
The existing restaurant has a calculated occupancy of 280 persons, is 4000 square
feet and is an A-2 occupancy. The proposed outdoor addition has 60 occupants, is
900 square feet and also is an A-2. Although the aggregate square footage (4000 +
900 = 4900) is less than 5000, the total number of occupants (340) now exceeds the
maximum allowable fire area of for an A-2 occupancy. Consequently, this will
trigger the requirement in NCBC-Section NCBC-903.2.1.2 for installing an
automatic sprinkler system in the outdoor covered addition and in the existing
restaurant.
In this example, one option to negate the requirement for sprinklers is to separate the
proposed outdoor covered addition from the existing restaurant with a fire barrier.
Thus, sprinklers are not necessary for code compliance because each fire area is
below the threshold level for triggering the A-2 occupancy requirement under
NCBC- 903.2.1.2. Note the following:
NCBC-707.3.9 addresses the required fire-resistance rating for dividing a single
occupancy (or multiple occupancies) into separate fire areas. NCBC- Table 508.4
provides the minimum required fire-resistance ratings for a fire barrier wall or
horizontal assembly to separate the same occupancy group or multiple occupancy
groups into separate fire areas.
Each fire area is evaluated independently for purposes of determining the
applicable provisions of the North Carolina State Building Codes.*
*NOTE: Means of egress from each fire area needs to be shown on the floor plan.
Code compliance of each fire barrier is to be evaluated for occupancy size, required
means of egress and for other life & safety requirements.
Plumbing Fixtures for the Existing Building and the Addition of an Uncovered Outdoor Area H.
or a Covered Addition - The addition of an uncovered or a covered outdoor space to serve an
existing restaurant, etc. will increase the design occupancy load of an existing building. The
plumbing fixture count shall be re-evaluated as follows for compliance with the current NCPC
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 14 of 16
(Chapter 4) and NCBC (Chapter 29):
Option # 1 – Addition only (uncovered or covered): Provide additional plumbing fixtures
for the calculated occupant load, under the current NCPC, for the addition to
accommodate the increase in the occupancy load for males and females created by the
construction of the uncovered outdoor area or covered outdoor space;
OR Option # 2 – Existing plus Addition (uncovered or covered): Calculate the design
occupancy load for the uncovered outdoor area or the outdoor covered space plus the
calculated load for the existing restaurant or bar, under the current NCPC, to determine the
total fixture count required for males and females. If the number of existing plumbing
fixtures is deficient by calculation to accommodate the addition plus the existing space,
provide additional fixtures to comply with the revised fixture count.
Energy Requirements for the Covered Addition I.
1. Unless a covered outdoor building space complies with the minimum commercial
building thermal envelope requirements of the NCEC, a permanent heating and/or cooling
appliance is not allowed to be installed to serve this space. In addition, duct work is not
allowed to be extended from the existing building to serve the covered outdoor addition
(Figure 11). DOI is unaware of any plastic or fabric enclosures, as addressed in 5.0-K of
this document, that comply with the Energy Code requirements at this time.
2. The 2012 NCEC does contain a provision in the 2012 NCEC indicates “Systems installed
to provide heating outside a building shall be radiant systems. Such heating systems shall
be controlled by an occupancy sensing device or a timer switch, so that the system is
automatically de-energized when no occupants are present.” (Figure 12).
Figure 11-Extending existing duct work from existing building
to serve covered outdoor space is not allowed by the NCEC.
Figure 12- Example of a permanent radiant heating
appliance.
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 15 of 16
Pliable Light Transmitting or Fabric Curtain System for Weather Protection at the Covered J.
Addition - For weather
protection, a pliable light
transmitting or fabric curtain
system are often proposed in
openings between columns
around the exterior perimeter
of covered outdoor spaces
(Figure 13). Code
requirements for these
systems are addressed in the
White Paper under “2012
Code Additions” by the
Evaluation Services Section
entitled “Pliable Light
Transmitting or Fabric Curtain
System for
Weather Protection at a
Covered Outdoor Space” that
is located on the NCDOI-
OSFM website at the following link:
http://www.ncdoi.com/OSFM/Engineering/engineering_wpt.asp
Guards at the Covered Addition - If any edge of the finished floor of the outdoor space is more K.
than 30” above finish grade, guards are required along the perimeter where this condition
occurs. NCBC-Section 1013 addresses the requirements for guards.
Structural Requirements for the Covered Addition - Roof and wall structures, including roof L.
covering, for covered outdoor spaces shall be designed and constructed to withstand wind or
other lateral loads, snow loads and live loads as required by NCBC-Chapter 16, with due
allowance for shape, open construction and similar features that relieve the pressures or loads.
Wind uplift is particularly important in the design of open sided covered structures. Weight
required to hold the structure down may control the foundation design. See #29 (Roofs) in
NCBC-Table 1607.1 for minimum roof live loads required by code.
Accessibility Requirements for the Covered Addition - This document does not address code M.
components for handicap accessibility. However, the addition is required to comply with
accessibility in the NCBC. For example, a new required exit serving the covered outdoor
space is required to be accessible, as addressed in NCBC-Section 1007.1.
Maintaining Means of Egress for the Existing Building during Construction of the Covered N.
Addition
1. During alterations, additions and/or repairs, a building can be even more vulnerable to an
emergency event, and egress components or other fire protection features (sprinkler
system, alarm system, etc.) cannot be temporarily compromised. This is a violation of the
Code, as addressed in NCBC-Section 3302.
Example: The code requires a restaurant to have two exits and one exit may be
Figure 13-Example of fabric curtain system with pliable light
transmitting material.
DOI File # WP-009-11 (Rev. 2012) Covered Outdoor Space Adjacent to Restaurant or Bar Page 16 of 16
temporarily closed during the construction of an uncovered or covered outdoor area. The
restaurant continues to be opened for business during construction. Consequently, an
alternate (temporary) code compliant 2nd
exit shall be provided until the original 2nd
exit
is reopened. At no time can only one exit be in operation, when 2 are required, when the
building is occupied.
2. If any means of egress components or other fire protection features are to be affected
temporarily during a construction project, a floor plan shall be submitted to the CEO that
indicates how a code compliant equivalency will be addressed.
REFERENCES 6.0
2012 North Carolina Building Code (NCBC) A.
2012 North Carolina Fire Prevention Code (NCFPC) B.
UL 924 (2006 Standard Reference Number) – Standard for Safety Emergency Lighting and C.
Power Equipment
2009 International Building Code Commentary by the International Code Council, Inc. D.
2009 International Fire Prevention Code Commentary by the International Code Council, Inc. E.
NFPA 101 (2006 Standard Reference Number) F.
Special uses and Mixed Occupancies, February 2001, by the Building Officials and Code G.
Administrators International, Inc.
2003 IBC Architectural Applications for Designers, August 2004, by the International Code H.
Council, Inc.
2006 International Building Code Commentary, September 2006, by the International Code I.
Council, Inc.
PHOTO RESOURCES 7.0
Figure 1- Patio Enclosure A.
Figure 2- Retractable cover B.
Figures 3 & 4- Taken By NCDOI C.
Figure 5- http://www.litrausa.com/Restaurant_Enclosures-12.html D.
Figure 6- Mixed use strip mall E.
Figure 7- Roll-a-Cover F.
Figures 8, 9, 10, 11, 12 & 13-Taken By NCDOI G.
This document does not constitute an evaluation of any vendor’s product nor does this document
imply that the Code Enforcement Official must approve any specific material, design, or method.
Top Related