MTS/T-BERD - 5800
2
Hardware Description
3
User Interface
RFC 2544
5
RFC 2544 Test Procedure
Select Test In the Select Test menu, ,at the top left corner of the screen, choose one of the following:
• For 10BASE-T, 100BASE-T, or 1000BASE-T Electrical Ethernet testing: Ethernet►10/100/1000► RFC 2544 ►L2 Traffic►P1 Terminate.• For 100BASE-FX Optical Fast Ethernet testing:Ethernet►100M Optical► RFC 2544 ►L2 Traffic►P1 Terminate.• For 1000BASE-SR, 1000BASE-LR, or other GigE Optical Testing: Ethernet►1GigE Optical►RFC 2544 ►L2 Traffic►P1 Terminate.• For 10GBASE-SR, 10GBASE-LR, other 10GigE Optical Testing: Ethernet►10GigE LAN► RFC 2544 ►L2 Traffic►P1 Terminate.
6
RFC 2544 Test Procedure - Configure
If this is the first time using the RFC2544 test and your unit does not have pre-loaded configuration files, tap the button next to “Start a New Configuration (reset to defaults)” and proceed to step 2.
Otherwise, tap the button next to “Load Configuration from a Profile”
Select the desired configuration, and tap . Tap to acknowledge successful load, tap the button, and tap the button next to Edit Configuration.
7
RFC 2544 Test Procedure - Symmetry
In the Symmetry configuration screen, verify that Throughput = Symmetric and Measurements = Loopback, then tap the button.
8
RFC 2544 Test Procedure – L2 SettingsOption Value(s) CommentFrame Type DIXEncapsulation None or VLAN See Work Order
Test Mode Traffic or LBM Traffic
Select “LBM Traffic” if the loopback device is an ALU 7705. Select “Traffic” for all other loopback devices.
VLAN ID See Work Order Option only displayed if Encapsulation = VLANUser Priority 0 (lowest)
Source Type Factory Default Tap the Set Loop Type and MAC Addresses or Set MAC Addresses and LBM links to configure these settings. (See below)
Destination MACEnter MAC address of the loopback device
Loop Type UnicastOptions only displayed if Test Mode = Traffic
EtherType 0800Auto-increment SA MAC No
Maint. Domain Level
See work order. Set to same value as ALU 7705 Options only displayed if Test
Mode = LBM TrafficEnable Sender TLV No (unchecked)
9
RFC 2544 Test Procedure – Other Settings
Use the or button at the bottom of the screen to advance through the wizard and configure the remaining settings as follows:
Screen Option Value(s) Comment
RFC 2544 Tests: Configuration Templates
Do you want to use a configuration template?
No
RFC 2544 Tests: Select Tests
RCF 2544 Tests Throughput, Latency, Frame Loss
Additional Tests Packet Jitter
10
RFC 2544 Test Procedure – Other Settings
RFC 2544 Tests: Utilization
Bandwidth Unit L1 Mbps
Maximum Bandwidth See Work Order Enter Committed Information Rate (CIR)
Frame Lengths
Select 1st, 4th, and 8th
Frame Lengths. If the MTU is greater than
1518 (1522 with VLAN), also enter and select the frame length of the MTU.
Deselect (uncheck) all other frame sizes.
RFC 2544 Tests: Throughput
Zero-in Process JDSU Enhanced
Measurement Accuracy To within 1 Mbps
11
RFC 2544 Test Procedure – Other Settings
RFC 2544 Tests: Frame Loss Test
Test Procedure RFC 2544 Standard
Bandwidth Granularity (L1Mbps)
Enter minimum value: 1 for 100Mbps
Ethernet 10 for Gigabit
Ethernet 100 for 10GigE
Test Ctls: Test Durations
Configure test durations separately? No
Duration 120 secondsThis will result in approximately 6 minutes of test time per frame length.Number of Trials 1
Test Ctls: Test Thresholds
Show Pass/Fail Select all ()
Throughput Threshold See Work Order Enter CIR
Throughput Frame Loss Tolerance (%) See Work Order Enter 0.000 if not specified
Latency RTD (µs) See Work Order
Enter threshold in µsecs (1 msec = 1000 µsec). Uncheck the Show Pass/Fail box if athreshold is not specified.
Packet Jitter (µs) See Work Order
Acterna Payload Version Version 2
12
RFC 2544 Test Procedure – Save Profile
In the Save Profiles screen, enter a Filename, and tap . Tap , tap , and tap twice.
13
RFC 2544 Test Procedure – Running the Test
Ensure that the loopback device has been setup, and tap to run J- QuickCheck to verify local connectivity, loop up the remote loopback device, and check available bandwidth.
14
RFC 2544 Test Procedure – Running the Test
Tap , and tap . The T-BERD will loop up the loopback device and run all configured tests.
Detailed results for each test can be viewed by tapping .
15
RFC 2544 Test Procedure – Create a Report
Tap twice and enter Customer name, Technician ID, Test Location, Work Order Number and Comments/Notes.
Tap again and tap
View the Report and tap
Y.1564
17
Y.1564 Test Procedure
Select Test In the Select Test menu, ,at the top left corner of the screen, choose one of the following:• For 10BASE-T, 100BASE-T, or 1000BASE-T Electrical Ethernet testing: Ethernet►10/100/1000► Y1564 SAMComplete ►L2 Traffic►P1 Terminate.• For 100BASE-FX Optical Fast Ethernet testing:Ethernet►100M Optical► Y1564 SAMComplete ►L2 Traffic►P1 Terminate.• For 1000BASE-SR, 1000BASE-LR, or other GigE Optical Testing: Ethernet►1GigE Optical► Y1564 SAMComplete ►L2 Traffic►P1 Terminate.• For 10GBASE-SR, 10GBASE-LR, other 10GigE Optical Testing: Ethernet►10GigE LAN► Y1564 SAMComplete ►L2 Traffic►P1 Terminate.
18
Y.1564 Test Procedure - Configure
If this is the first time using the Y.1564 test and your unit does not have pre-loaded configuration files, tap the button next to “Start a New Configuration (reset to defaults)” and proceed to step 2.
Otherwise, tap the button next to “Load Configuration from a Profile”
Select the desired configuration, and tap . Tap to acknowledge successful load, tap the button, and tap the button next to Edit Configuration.
19
Y.1564 Test Procedure - Setup
Use the and buttons at the bottom of the screen to advance through the wizard and configure Layer 2 Network Setting as follows:
Screen Option Value(s) Comment
Connect: SymmetryThroughput Symmetric
Measurements Loopback
Connect: Configuration Templates
Do you want to use a configuration template? No
Connect: Local Settings Frame Type DIX
Network Services
Number of Services See Work Order Enter 1 if not specified.
Test Mode Traffic or LBM Traffic
Select “LBM Traffic” if the loopback device is an ALU 7705. Select “Traffic” for all other loopback devices.
20
Y.1564 Test Procedure - Setup
Network: Services, LBM Settings (Advanced)
Maint. Domain Level See Work OrderTap the LBM settings link to configure these settings.Enable Sender TLV No (unchecked)
Network: Services, Network Settings (Advanced)
Frame Size See Work Order; Enter EMIX if not specified
Tap the DA MAC and Frame Size settings link to configure these settings.Dest. MAC Address See Work Order
Network: Tagging
Do Services have different VLAN ID’s or User Priorities? See Work Order Select No if not specified
Encapsulation See Work Order None or VLAN.Select None if not specified
VLAN ID See Work Order
User Priority See Work Order
SLA: SLA Throughput
Enable Aggregate Mode No (unchecked)
CIR See Work Order
EIR See Work Order Enter 0 if not specified
Policing
Select if CIR < line rate.
Deselect if CIR = line rate
21
Y.1564 Test Procedure - Setup
SLA:SLA Burst
Would you like to perform burst testing? See Work Order Select No if not specified
Burst Test Type Committed Burst SizeCBS See Work Order
SLA: SLA Performance
Frame Loss Ratio See Work Order Enter 0.000000 if not specified.
Frame Delay (RTD, ms) See Work Order
If not specified: 50 for Circuit Emulation 20 for EPL/EVPL 10 for Mobile Backhaul
Delay Variation (ms) See Work Order
If not specified: 20 for Circuit Emulation 20 for EPL/EVPL 2 for Mobile Backhaul
Acterna Payload VersionSelect “Version 3” if loopback device is another T-BERD.Otherwise, select “Version 2”
Test ControlsNumber of Steps Below CIR 3
Step Duration (Sec) 15Test Duration 5
22
Y.1564 Test Procedure – Save Profile
In the Save Profiles screen, enter a Filename, and tap . Tap , tap , and tap twice.
23
Y.1564 Test Procedure – Running the Test
In the Select Y.1564 Tests screen, select all Services, Service Configuration Test, Service Performance Test, and Throughput (RFC-2544). Enter the total (Sum) CIR for all combined services in the Max. (L1 Mbps) field, then press
24
Y.1564 Test Procedure – Running the Test
Ensure that the loopback device has been setup, and tap to run J-QuickCheck to verify local connectivity, loop up the remote loopback device, and check available bandwidth.
25
Y.1564 Test Procedure – Running the Test
Tap , and tap . The T-BERD will run all configured tests.
Detailed results for each test can be viewed by tapping .
26
Y.1564 Test Procedure – Create a Report
Tap twice and enter Customer name, Technician ID, Test Location, Work Order Number and Comments/Notes.
Tap again and tap
View the Report and tap
Software Update
28
Software update
Power On - Press and hold the ON/OFF button to turn on the T-BERD 5800v2. AC Power - Connect the AC power
adapter to the power connector on the side of the T-BERD 5800v2. LAN Connection - Connect the
Ethernet Management Port on the side of T-BERD 5800v2 to a network connection with internet access, using CAT 5E or better cable.
29
Software update – Network Upgrade
Press the System icon, , at the top of the start-up screen, to display the System Menu.
30
Software update – Network Upgrade
Press the Network icon, , to display LAN Settings. Set IP Mode to “DHCP” for automatic IP address assignment or “Static” for manual input.
After configuring LAN settings, press the System icon, , to redisplay the System Menu.
31
Software update – Network Upgrade
Press the Upgrade icon, , to display upgrade methods.
32
Software update – Network Upgrade
Press to display upgrade settings. Ensure that Server Address = “5800v2.updatemyunit.net”
33
Software update – Network Upgrade
Press to show the upgrade versions available at upgrademyunit.net.
Press , and press to initiate the upgrade.
34
Software update – USB Upgrade
Using an internet browser on your PC or laptop, go to http://updatemyunit.net/
35
Software update – USB Upgrade
Click on to display the T-BERD 5800v2 upgrade portal.
Download the file by clicking one of the flags and save extract the files in a USB
36
Software update – USB Upgrade
Press the Upgrade icon, , to display upgrade methods.
37
Software update – Network Upgrade
Press to show the upgrade versions available at upgrademyunit.net.
Press , and press to initiate the upgrade.
Top Related