1
markilux
Mounting instructions conservatory awning
overview
Table of contents
markilux 8800 / 8800 tracfi x
1
234
5
Scope of the DeliveryThis conservatory awning is delivered with the cassette fully pre-assembled, a front profi le and 1 pair of guide tracks in protective foil. The drive belts have been matched to the cover length in the factory. The number of fi xture brackets depends on the awning size and fi xture type, see sales literature.
markilux safety instructions
markilux mounting instructions
1. Overviews and fi xing types Page 5
1.1. Mounting types and mounting brackets Page 5
1.2 Mounting systems Page 5
1.3 Mounting bracket Page 6 - 7
1.4 Dimension overviews and fi xture dimensions Page 8
1.4.1 Bottom fi xture (fi xture method 11) Page 8
1.4.2 Face fi xture (fi xture type 12) Page 9
1.4.3 Track fi xture (fi xture type 32) Page 10 - 11
1.4.4 Track fi xture on conservatory rafters (fi xture type 33) Page 12
1.4.5 Reveal fi xture (fi xture type 16) Page 12
2. Fitting the brackets (e.g. bottom fi xture) Page 13
3. Awning installation Page 14
4. What to do if the awning has no tension in the middle position? Page 17
5. The course taken by the drive belt Page 17
6. Motor Page 18
6.1 Motor connection Page 18
6.2 Motor connection data markilux 8800 / 8800 tracfi x Page 18
6.3 Motor connection data coupled unit markilux 8800 / 8800 tracfi x - optional Page 19
7. Fixing the cassette coupling bracket (e.g. bottom fi xture) - optional Page 19
8. Coupling single awnings - optional Page 19 - 21
markilux handover declaration
1 Cassette2 Guide track3 cover support tube 4 Front profi le5 Awning cover
17/07/2013 7061438_TD
markilux safety instructionsImportant information for the installation of markilux awnings
markilux
1. Who is allowed to fi t markilux awnings?The markilux installation instructions are to a qualifi ed mechanic who has skilled knowledge in following domains:• Occupational and operational safety and accident prevention regulations• Handling of ladders and scaffoldings• Handling and transport of long and heavy component parts• Handling of tools and machines• Fixture device placement• Assessment of building materials• Commissioning and operation of the productIf any one of these qualifi cations is not existent, a qualifi ed installation fi rm must be engaged.
Electrical works: electrical installations must be carried out by a certifi ed electrician according to VDE 0100. The enclosed installation instructions of the supplied electronic devices are to be observed.
We recommend installation be carried out by at least two people. Larger awnings may require three persons.
2. Before beginning the installation it is to be checked, ...• does the number and type of fi xture brackets match the order?• do the specifi cations made with the order concerning the fastening background correspond with the actual fastening background at hand (only
for folding-arm awnings)?If irregularities which may affect the safety of the unit or its users are determined, then the installation must not be undertaken.
3. Reading and passing on the instructions
The security and attachment notes as well as the operation manuals are to be read and observed!The markilux operating guide, as well as the setting instructions of the motor, switch and controller manufacturers are to be handed over to the user with a written confi rmation and fi tted wind class (see handover declaration). He is to be comprehensively informed about the safety and usage information of the awning. With nonobservance and improper operation, the awning can suffer damage and accidents can occur.
4. Working at greater heights
If the awning construction has to be pulled up into a higher area with rope support, then the awning has• to be taken out of the package,• should be connected with pull ropes in such a way that these cannot slip out,• are to be pulled up up evenly in an horizontal position.The same also applies for awning deinstallation.
Working at heights increases the risk of falling.Appropriate climbing aids and safety rails are to be used whilst installing the awning.
5. Wind resistance classes
markiluxSchmitz-Werke GmbH & Co. KG
Hansestraße 87D-48282 Emsdetten
DIN EN 13561Awnings for exterior applications
wind resistance class 2markilux folding-arm awnings
markilux 710/810, 720/820, 725/825, 750/850, 730/830, 740/840, 745/845, 893, 869/869 zip/889/889 zip (depending on size), 8850
wind resistance class 3markilux 760/860, 620 zip, 660 zip, 680 zip, 780/880, 8800/8800
zip, 869/869 zip/889/889 zip (depending on size),pergola 110/210
The awning fulfi lls the requirements of the wind resistance class specifi ed in the CE conformity marking (explanations see "handover declaration").In assembled condition, it only fulfi lls these requirements if...• ... the awning is mounted in accordance with the type and number of
consoles recommended by the manufacturer.• ... the instructions of the fi xing material manufacturer regarding the
used dowels were followed during the assembly.• ... the installation of folding-arm awnings was carried out considering
the
www.markilux.com
6. Partlyassembledawnings
In case of awnings that come partly-assembled from the factory – e.g. coupled folding-arm awnings without cover - the spring-loa-
ded parts (see figure: Example folding-arm awning) are secured against unintentional opening. These securing means must be removed only af-ter the complete assembly.
The labelled awning parts are under spring tension and can pose an high injury risk.
7. Foldingarmawningswithservogearforhandcrank
The servo gear unit of folding-arm awnings (marking by label) must not be dismantled. It is under great tension!
If the awning cloth or the gear have to be changed, kindly enquire before about the instructions "Whatistobedone,iftheservogearunithastobedismantled?.
8. Uncontrolledoperation
When working in the range of travel of the awning (see figure: ex-ample folding-arm awning) the automatic control has to be deacti-
vated. There is a risk of crushing body parts and falling.
Additionally, the installer must ensure that the unit cannot be unintentionally operated during works. The power supply should be disconnected i.e. by removing or turning off safety fuses and/or removing the power cables and motor socket gear. For works on manually operated units the crank should be removed and stored safely.If awnings are operated by more than one person, an override locking device (controlled circuit breakers from outside) must be installed so that any retraction or extension of the awning is not possible.
9. Properintendeduse
Awnings may only be used according to the purpose defined in the operation manual. Alterations like rebuilding or enlargements which are not intended by the manufacturer may only be carried out with the manufacturers written approval.Additional awning burdens by means of object attachments or or rope wearing can result in damage or dropping of the awning and are therefore not allowed.The awning must not be subjected to high temperatures, heavy vibrations, jarring or heavy mechanical stress.A build up of snow behind the awning can be avoided by installation of snow stoppers (snow collecting grid or the like).
10. Crushandshearzones
Depending on the type of awning there are crush and shear zones, e.g. between front profile and cassette and between moving parts. Items of clothing or limbs can be grabbed by the unit and pulled in. (see figure: example folding-arm awning.)
If the awning is installed at a height less than 2.5 metres above accessible traffic ways, then the awning may only be operated by a pushbutton switch which enables the moving parts to be viewed. Electric controls, radio-controlled motors with click in-switches are not permitted for such installations.
5
www.markilux.com
1.1 Mounting types and mounting brackets1. Overviews and fi xing types
11 12
76061.L76062.R(76180.)
76017.
76063.L76064.R(76181.) 76046.
14 16
76046.76061.L76062.R(76180.)
76077. L76078. R(76180.) 76053.
21 22
76061.L76062.R(76180.)
76049.76049.
76063.L76064.R(76181.)
31 32
76017. 76017. 76046.76046.
33 41
76735. 76735.76063.L76064.R(76181.)
76052.
51 61
76046.76052.
76063.L76064.R(76181.) 76046.
76067.L76068.R(76198.)
71 81
76067.L76068.R(76198.) 76052.
76067.L76068.R(76198.) 76046.76052.
markilux mounting instructions
Individual bracket combinations - see "Fixtures, fi ttings and accessories" in the sales documentation. Please note the minimum quantity in accordance with the width and extension! Mounting Type 11, 14, 16, 21, 31, 32: from a fi xture width (MA) of 601 cm an cassette support assembly, 76183., is required!
1.2 Mounting systems Attention!Basically the following is applicable for all mounting systems:
1. The mounting material manufacturers (e.g. Fischer, Hilti, Upat, etc.) offer different mounting systemsaccording to the undersurface. If the conditions for the mounting are met according to DIN EN 13561, the wind resistance class 3 for the mounting can be confi rmed to the user.
Mounting material is not delivered, as different undersurfaces (e.g. concrete, lime sand stone, autoclaved aerated concrete, etc.) require different types of mounting material
3. IMPORTANT: The brackets must be aligned with each other! When subsurfaces are uneven, the clearances are to be checked using a cord pulley and if required compensated accordingly. Due to the horizontal mounting of the folding-arm awning and the perpendicular fi t of the mounting brackets, the smooth functioning of the folding-arm awning is guaranteed.
6
www.markilux.com
Face fixture bracket assem-bly, pitch adjustment range5 to 45°
Face fixture bracket assembly,pitch adjustment range5 to 45°
Cassette coupling bracket assembly, face fixture bracket,pitch adjustment range5 to 45°
left right
face fixture
76063. 76064. 76181.
40 126
Bottom fixture bracket assemblyfor mounting onto a frame
40
126
Bottom fixture bracket assembly for mounting onto a frame
Cassette coupling bracket assembly for mounting onto a frame
left right for coupling point
76061. 76062. 76180.Raised cassette fixture bracket assemblyfoot can be moved up to 45° backwards, head of cas-sette fixture bracket can be tilted forwards up to 45°
Raised cassette fixture bracket assemblyfoot can be moved up to 45° backwards, head of cas-sette fixture bracket can be tilted forwards up to 45°
Raised cassette fixture bracket assemblyfoot can be moved up to 45° backwards, head of cas-sette fixture bracket can be tilted forwards up to 45°
left, for mounting onto frame
right, for mounting onto frame
coupling point for moun-ting onto frame
76067. 76068. 76198.
38
132
100
Cassette support assemblyfor mounting onto frame
140
132
38
Cassette support assembly for mounting onto frame
Cassette coupling bracket assembly for track fixture, rigid
Höhe 100 mm height 140 mm Fixture type 31 and 32
76183. 76184. 76069.
AccessoriesStorm safety bracket assembly for the cassette (recom-mended in windy locations and as an additional safety measure for the cassette)
29
20
34Diagonal tensioning kit(2 wire tensioners, 1 sup-port wire)
270
60 Bracket assembly for light/wind/rain sensor
76197. 71790. 76050.wall sealing profile
30
44
40
Angle bracket to prevent deflection of the cover support tube for bracket height 100 mm
Support assembly to prevent deflection of the cover support tube, can be shortened to between 70 and 320 mm(with clamp plate)available by the metre
assembly example: see face fixture with wall sealing profile
for assembly example refer to section "Installation dimensions"
for assembly exampleInstallation dimensions
77780. 76065. 71780.bracket assembly for cover support tube
coupling bracket assembly for cover support tube
Storm security device assembly / track slider
76019. 76059. 76235.
108
Bottom fixture assembly right reveal 76076and left 76077.
76076. + 76077.
1.3 Mounting bracketsCassette fixture brackets
7
www.markilux.com
70 40
Track bracket assembly for track fixture, rigid
track bracket assembly for track fixture
refer to section "Installation dimensions"
available by the metre, undrilledmax. length 6 m76017. 76013.
9
85 110
40 20
10
Fixture dimensions of ad-justable top track brackets
9 110 40
85 Track bracket assembly with adjustable head
9 110 40
85
Track bracket assembly with adjustable head
Höhe 100 mm height 140 mm
refer to section "Installation dimensions"
refer to section "Installation dimensions"
76046. 76048.
9
60
45
85
110
Track bracket assembly with adjustable foot plate
spacer plate for track bracket 60
110
9
85
10
8,5
adjustable foot plate for track bracket assembly
Höhe 100 mm 110 x 40 x 10 mm
refer to section "Installation dimensions"
76199. 78570. 78165.
9
85
40 110
Double track bracket assembly with adjustable head
Universal track bracket assembly
9
40 110
Track bracket assembly for transom fixture
Höhe 100 mm Höhe 100 mm Höhe 100 mm
refer to section "Installation dimensions"
refer to section "Installation dimensions"
refer to section "Installation dimensions"
76191. 76054. 76055.
9
85
40 110
Double track bracket assembly with adjustable head
Track bracket assembly with adjustable head
Double track bracket assembly with adjustable head
height 140 mm height 100 - 500 mm height 100 - 500 mm
refer to section "Installation dimensions"
refer to section "Installation dimensions"
refer to section "Installation dimensions"
76192. 76047. 76193.Universal track bracket assembly
Track bracket assembly with adjustable head and foot
Double track bracket assembly with adjustable head and foot
height 140 - 500 mm height 200 - 500 mm height 200 - 500 mm
refer to section "Installation dimensions"
refer to section "Installation dimensions"
refer to section "Installation dimensions"
76053. 76045. 76194.vario-V bracket assembly for track fixture
Flat bracket assembly for lateral track fixture with adjustable head
Retaining plate
refer to section "Installation dimensions"
refer to section "Installation dimensions"
110 x 60 mm
76052. 76049. 78158.
30
110
9
Track bracket assembly for track fixture directly on the conservatory rafters
110
50
85
65 50
15
25
Ø9
Mounting bracket
without mounting screws
Mounting bracket assembly
76099. Mounting bracket incl. mounting screws as an addition to fixture type 32
76735. 76098. 76099.
Track bracket
8
www.markilux.com
M = overall awning widthH = projectionFW = width between fixing pointsMA = fixture width = awning width between fixture pointsS = cross section1 = cassettebottom fixture bracket2 = track bracket with adjustable head3 = from an extension (H) of 401 cm an additional track bracket
with adjustable head is required4 = from a fixture width (MA) of 601 cm an cassette support
assembly, 76183., is required
1.4 Dimension overviews and fixture dimensions
1.4.1 Bottom fixture
Overview of dimensions, see chapter 1.3.1 - 1.3.3. Respective information on the mounting dimensions of other mounting types (see chapter 1.1) can be found in our sales documentation.
Overview of dimensions markilux 8800 / 8800 tracfix 2
08
21
105
70
116
37
84
210 H
min. 100max. 1000
30
MA
BA
60 50
187
M
76061.76062.(76180.)
76017.
A
AS A-A
Fixture type 11
5 = cover support tube (the required quantity can be found in the size grid in our sales documentation)
6 = from a fixture width of (MA) 451 cm an additional support bracket (or adjustable support bracket) for awnings with cover support tube is required
76061. = bottom fixture bracket assembly, rigid, left76062. = bottom fixture bracket assembly, rigid, right76180. = cassette coupling bracket assembly76017. = track bracket for track-only fixture, rigid
measurements in mm
9
www.markilux.com
1.4.2 Face fixture
37
116 60
70
105
H
210
187
1
6 2
04
84 AX
MA
30
50
BA
min. 100max. 1000
A
AS A-A
76063.76064.(76181.)
76046.
M
WW AX5° 26
10° 3215° 3720° 4325° 4730° 5035° 5240° 5345° 53
Overview of dimensions markilux 8800 / 8800 tracfix
Fixture type 12
M = overall awning widthH = projectionFW = width between fixing pointsMA = fixture width = awning width between fixture pointsW = pitchAX = distance cassette - wallS = cross section1 = face fixture cassette bracket2 = track bracket with adjustable head3 = from an extension (H) of 401 cm an additional track bracket
(for fixture types 22, 41, 51) is required
4 = from a fixture width (MA) of 451 cm an additional cassette coupling bracket is required
5 = cover support tube (the required quantity can be found in the size grid in our sales documentation)
76063. = face fixture cassette bracket assembly, pitch adjustable from 5°to 45°,left
76064. = face fixture bracket assembly, pitch adjustable from 5°to 45°, right
76181. = coupling cassette bracket assembly, face fixture, pitch adjustable from 5°to 45°
76046. = track bracket assembly with adjustable head, height 100 mm
measurements in mm
10
www.markilux.com
1.4.3 Track-only fixture
37
105
208
116
70
60
210 H
187
84
21
min. 100max. 1000
30
50 MA
BA
76046.
76046.
M
S A-A
A
Amin. 300max. 400
Overview of dimensions markilux 8800 / 8800 tracfix
Fixture type 32
M = overall awning widthH = projectionFW = width between fixing pointsMA = fixture width = awning width between fixture pointsS = cross section1 = track bracket with adjustable head2 = track bracket with adjustable head3 = from a fixture width (MA) of 601 cm an cassette support
assembly, 76183., is required
4 = from a fixture width (MA) of 451 cm an additional cassette/casing support is required
5 = cover support tube (the required quantity can be found in the size grid in our sales documentation)
6 = from a fixture width of (MA) 451 cm an additional support bracket (or adjustable support bracket) for awnings with cover support tube is required
76046. = track bracket assembly with adjustable head, height 100 mm
measurements in mm
11
www.markilux.com
100
HH
MA = BA MA = BA
M M
45 MB = 300 45 MB = 300 HT
M = overall awning widthFW = width between fixing points = MAMA = awning fixture width = BA
BR = bracket fixture rangeHT = bracketHH = fixture bracket height
HT 76191. 76192. 76193. 76194.HH 105 145 105 to 505 205 to 505
dimensions in mm
Fixture dimensions with additional mounting bracket assembly 76099. for fixture type 32
M
BC
MA
50
29
6
50 50
50
M
50
69 31 BC
MA
14
15
~14
14
15 2
9 6
50
~14
50
M
50
75 BC
MA
14
15 2
9 6
50
~14
A-A: V1 A-A: V2 A-A: V3
85
25
9
110
15
65
9
6
50
50
H
min. 100max. 1000
A
125
105
76099.
228
1
87
min. 300max. 400
A
76099.
76099.76099.76099.
M = overall awning widthMA = awning fixture width = order widthA-A = in cross sectionBC = awning width between fixture points
H = projection76099. = mounting bracket assembly with mounting screwsV1, V2, V3 = variant 1, 2 and 3
dimensions in mm
Installation dimensions for fixture type 32 with double track bracket for single units
12
www.markilux.com
1.4.4 Track-only fixture on conservatory rafters
Fixture type 33
84
208
37 105
110
H 1
87
21
min. 100max. 1000
A
A
C
min. 300max. 400
C
30 15
30
105
R7,50
125
60 116
MA
BA
M
A-A
76735.
50
dimensions in mmM = overall awning widthMA = awning fixture width = order witdth = M minus 100 mmA-A = in cross sectionFW = width between fixing points
H = projection76735. = track bracket assembly for track fixture directly on the
conservatory rafterC = detailed drawing
from a fixture width (MA) of 601 cm an cassette support assembly, 76183., is required1.4.5 Reveal fixture
Fixture type 16
76077.76078.(76180.)
BA
37
105
84
A
116
MA
76054.
A-AM
76046.
25
B
min. 100max. 1000
A76054.
208
187
2
1
210 H
60
B
M = overall awning widthMA = awning fixture width = order witdth = M minus 100 mmA-A = in cross sectionFW = width between fixing pointsH = projectionB = detailed view
76077. = bottom fixture left reveal76078. = bottom fixture right reveal76180. = coupled cassette bracket for bottom fixture76046. = track bracket with adjustable head 100 mm76054. = universal track bracket assembly height 100 mm
from a fixture width (MA) of 601 cm an cassette support assembly, 76183., is required
dimensions in mm
13
www.markilux.com
3. Awning installation
1
4
2
3 56 6 7
1. Unpack awning from the box (pay attention to marking "top"). Do not remove the protective foil (1) of the front profile and the transport belt fixings (3 - adhesive strips, 4 - Styro-foam wedges) from the guide tracks (2).
2. Fit the cassette (5) to the bottom fixture bracket (6) you have already fitted.
3. Tighten the SW 5 allen key size cheese-head screws in the clamp plate (7) of the bottom fixture brackets (6).
9
8 2
10
213
12
11
4. Unscrew the countersunk head screw (8) at the left side cheek and remove the inspection cover (9).
5. Place the left guide track (2) the on track bracket (10) and clip it in place; do not screw it down tight yet.
6. Slide the guide track profile (2) about 2 to 3 cm over the rollers of the front profile bogey onto the end cap (11). Remove the tape holding the drive belt in place (adhesive strip) from the guide track profile. The lug-end of the drive belt (12) must be fed over the belt roller (13).
2. Fitting the brackets (e.g. bottom fixture)
1 MA MA
1MA
2 2MA
1. Hold the cassette bracket (1) in place, mark the drill holes at axial distance from one another and drill (M8 screws). Attention! All brackets must be aligned with each other!
2. Fix the bottom fixture cassette brackets in place(1).
3. Hold the track brackets (2) in place [from H = 401 cm, also (3)], mark the fixing points at axial distance from one another and drill the holes (M8 screws). Attention! Observe respective figure under chapter 1.3.1 to 1.3.3!
4. Fix the track brackets (2) in place. Measure all brackets diagonally!!
14
215
1416 2
10
6a. Attention! For awnings with tracfix system, the cover has to be threaded in the plastic track (15) with the "zip" (14) for the function of the tracfix system, before the guide track (2) of the awning is slid onto to end cap, as described under point 6.
7. Push the guide track profile (2) up to the stop and secure with a SW 6 Allen key cheese-head screw (16). If the guide track profile has to be loosened or removed: Unscrew the cylindrical head screw SW 6 (15) about 15 mm and loosen the connection by means of beating lightly on the screw head!
8. Tighten the jaws of the track bracket (10) SW 6 Allen key.
18
17
12
18
17
12
17
9. Lift the lug-end of the drive belt (12) up. Guide the assembly aid (17) between the fabric roller (18) and the rear of the cassette with the thicker part facing up.
10. Push assembly aid (17) through and guide around the fabric roller (18).
11. Push the lug-end of the drive belt (12) through the slot in the assembly aid (17). Attention! Do not twist transport bands!
19
1712
18
19
1218
12. Pull the assembly aid back out (17). In so doing the drive belt (19) is guided around the underside of the fabric roller (18). Detach the lug-end of the drive belt (12) from the assembly aid.
13. Attention! The drive belt has to be passed around the fabric roller a second time, so push the assembly aid through again and repeat paragraphs 9. to 12.
14. Slip the lug-end of the drive belt (12) underneath the first wrap of drive belt (19) and insert it into the keyway in the fabric roller (18).
18191
21 20 4 2
15. Attention! Ensure that the belt rolls up cleanly on itself on the fabric roller (18). Do not twist the drive belt (19)! Repeat points 3. to 15. at the right side.
16. Remove protective foil (1) from the front profile (20). Pull off sealing cap (21) from the projection profile (right and left).
17. Remove the remaining poystyre-ne blocks holding the drive belt in place (4) from the guide track profile (2) (on both the right and left).
15
www.markilux.com
22
19 20
19
2222
19
18. Pull the free end of the drive belt with fluffy velcro (19) towards the front profile (20) and connect it to the red end of the velcro strip (22) (right and left track profile).
19. Attention! The coloured end of the velcro strip (22) must be in line with the fluffy velcro end of the drive belt (19) and they must be connec-ted over their entire surfaces.
20. Carefully pull the drive belt (19) around the tensioning module with the help of the velcro strip (22) (see chapter 5 - course taken by the drive belt) While doing this, the drive belt must be held slightly under tension at both ends. Avoid forced or jerky pulling actions (both right and left).
19
19
23219 18
13
21. Pull the drive belt (19) tight. Do not cut off the loose end of the drive belt (both right and left).
22. By pulling the drive belt (19) out of the guide track (2), put pressure on the tensioning module until the split-pin (23) can be withdrawn easily (on both the right and left). The awning is now under tension.
23. At the inspection openings check transport bands (19) for twisting and correct seating on the fabric roller (18) and the belt rollers (13).
13
19 224
22426
25
24. Check transport bands (19) in the track profiles (2) for twisting and correct seating on the belt rollers (13).
25. For awnings with cover support tube: Establish positions for the cover support tube brackets (24) (on both the right and left). Clip the left cover support tube bracket to the guide track (2) and firmly tighten the jaws of the bracket with a SW 6 spanner.
26. Push the cover support tube (25) onto the screw (26) of the bracket (24).
16
www.markilux.com
25
24
26
2
d1
d1
27. Slide the pin (26) of the right cover support tube bracket (24) into the cover support tube (28). Clip the bracket (24) to the guide track (2) and tighten the clamping jaws of the bracket with an SW 6 spanner.
28. Measure the awning diagonally (d1) and align, as otherwise smooth functioning is not guaranteed. Attention! It is important that the guide tracks are parallel. The max. fixture tolerance (in particular for the tracfix function) is 3 mm as otherwise smooth operation cannot be guaranteed. Subsequently tighten all screws of the fixture brackets.
29. Extend and retract the awning for functional testing. Attention! The lower end position is not programmed for the standard motor without radio. Take care that the extension profile does not damage the conservatory when moving the awning. Make sure you stop before. See also point 6. motor drive.
181918
12
Attention! If the awning cloth has enough tension in central position, see chapter 4. What is to be done, if.... If the position of the drive belt is incorrect, see paragraphs 30. to 32.
30. Check the position of the drive belt (19) on the fabric roller (18) when the awning is retracted. Ideally, the fabric roller will be in the position shown. The transport band envelops the fabric roller with 1.5 wrappings.
31. If, when the first wrap of the drive belt has been unwound, the lug in the drive belt (12) is in the upper area of the fabric roller (18), then trouble-free operation of the awning is still guaranteed.
1821 20
9
8
32. Should there be no drive belt left on the fabric roller (18), paragraphs 9. to 15. have to be repeated. For this purpose the gas piston has to be secured again as described in chapter 4 "What to do, if....".
33. Roll up the drive belt together with the length of velcro, insert it into the front profile (20) and put on the end cap (21) (on both the right and the left).
34. On both end caps fix the inspec-tion covers again (9) using the countersunk head screws (8).
17
www.markilux.com
5. The course taken by the drive belt
4. What to do if the awning has no tension in the middle position?
19
232By pulling the drive belt (19) out of the guide track (2), bring the hole in the internal gas piston into conver-gence with that of the guide track and re-insert the split-pin (23) (on both the right and the left). The drive belts are now now longer under tension and the gas pistons are held securely in position. Now tighten the drive belts as described in chapter 3, paragraph 21 and tension the awning again as in paragraph 22.
5 = cassette12 = belt roller18 = fabric roller19 = drive belt20 = projection profile
18
www.markilux.com
6. Motor drive6.1 Motor connectionThe electrical connection for the motor drive and/or control system connection is to be carried out according to the instructions of the manufacturer of the motor and control system. Modifications, especially concerning the motor, the control system and the connecting supply lines require authorisation in writing.
The installation and adjustion instructions are to be observed. They can be found at the motor cable or accompany the awning. RTS motors carry an additional note on setting the motor at the motor cable. The inbuilt motor switches off on reaching a rated performance for the upper limit position (reduced torque auto-stop function).
Attention! The lower limit position has to be adjusted in accordance with the motor instructions for a standard motor (stop on reaching a particular awning position: point stop). This setting is not set in the factory.
The lower limit position is preset for RTS motors.
Instructions for further electric components are inside the belonging package.
Attention!The rolling up of the fabric on the fabric roller from below during retraction could lead to damage to the awning. Should you need to change the end stops, it is indispensable to pay attention to the sense of rotation!
Sense of rotation during retraction:
6.2 Motor connection data markilux 8800 / 8800 tracfix
180
8
130 58 26
Cable outlet for motor operation:
markilux 8800 / 8800 tracfix
wireless (433 MHz) U = 230 V~ / 240 W, 50 Hz, I = 1.0 A
with radio IO technology (868 - 870 MHz) U = 230 V~ / 240 W, 50 Hz, I = 1.1 A
wired U = 230 V~ / 246 W, 50 Hz, I = 1.2 A
measurements in mm
19
markilux
Mounting instructions conservatory awning
markilux 8800 / 8800 tracfi x coupled units
18/07/2013 7061442_TD
Attention! Observe the technical instructions as for the single unit!
7. Fixing the coupling bracket (example bottom fi xture)Place the brackets as described in the instructions for the single unit. The middle brackets are to be fi xed as follows:
1. The coupling bracket is centred directly at the coupling spot of the awning! Hold the bottom coupling bracket (1), mark the drill holes at axial distance from one another and drill (screws M 8). Attention! All brackets must be aligned with each other!MA = awning fi xture width
2. Fix coupling bracket (1). 3. Hold the track brackets (2), mark the fi xing points at axial distance from one another and drill the holes (M8 screws). A second track bracket has to be fi tted from an extension of 401 cm.
4. Fix the track brackets (2) in place. Measure all brackets diagonally!!
8. Couple single awnings
1
2
1 3
4
6 3
5
4
75 75
1. Unscrew the raised head screws (1) and remove the inspection cover (2).
2. Fix the drive awning (3) in the bottom fi xture bracket (4). The bottom coupling bracket has to be aligned centred.
3. Align the drive awning (3) in such a way that the coupling point of the cassettes (5) is in the middle of the bottom coupling bracket (4).
[dimensions in mm]
6.3 Motor connection data coupled unit markilux 8800 / 8800 tracfi x
markilux 8800 / 8800 tracfi x
wireless (433 MHz) U = 230 V~ / 290 W, 50 Hz, I = 1.25 A
with radio IO technology (868 - 870 MHz) U = 230 V~ / 290 W, 50 Hz, I = 1.50 A
wired U = 230 V~ / 260 W, 50 Hz, I = 1.15 A
20
www.markilux.com
6 min. 50
73
89
10
6
4. Tighten the SW 5 cylinder head screws at the clamp plate (6) of the brackets to secure the drive awning.
5. Fit the awning to be coupled (7) to the bottom couple bracket with a clearance of 50 mm to the drive awning (3). Slightly lift the fabric roller (8) and push the awning to be coupled onto the socket (9) and the pincher carriages (10) of the drive awning (3).
6. Tighten the SW 5 cylinder head screws (6) at the clamp plate of the brackets fo secure the awning to be coupled.
11
1312
12 5
1115
1415
14
18
717
16
7. Push the coupling track (11) via the track rollers (12) onto the auf den cassette coupling bracket (5) until the stop. While doing this, guide the lug-end of the drive belt (13) into the cassette as described for single units. Attention! Do not twist transport bands! See point 7a for tracfix system.
7a. Attention!For awnings with tracfix system: Thread the cover of both awnings with the "zip" (14) in the respective plastic tracks (15) [in the guide track (11)]. Subsequently attach the guide tracks and fix them.11 = guide track with inside plastic track (15)
8. Fix the coupling track by tighte-ning the SW 5 threaded pin (16). Turn the fabric roller of the coupled awning (7) until the roller tube grooves (17) of the cloths are aligned with each other. Tighten one of the four SW 5 threaded pins (18) that are offset by 90° in the fabric roller of the coupled awning (7).
21
www.markilux.com
3
719
202 1
8a. Attention!Awnings with tracfix system: The fabric roller grooves are concealed by the cover. The fabric roller groove of the coupled awning (7) is not aligned with the drive belt groove. Turn the fabric roller of the coupled awning (7) until the notch in the coupling cap (19) is aligned with the drive belt groove (20) of the drive awning (3).
9. Attention! Prior to functional testing, extend the awning until the remaining of the four SW 5 threaded pins can be fixed in the fabric roller. Subsequently attach the inspection cover (2) with the raised head screws (1).
10. For further fixing steps refer to the fixing instructions for single units (chapter 3, point 9.- 34.).
22
21
222
3
11. In case the front profiles (21) and (22) do not extend and retract uniformly after the trial run of the awning, the covers will require readjustment.
12. Readjustment of the covers: Unscrew the middle inspection cover (2) and loosen the four threaded pins in the fabric roller of the awning to be coupled.Align the front profiles at the same height: either by pulling the front profile (22) of the awning to be coupled or by using the drive of the drive awning (3). Subsequently tighten the four SW 5 threaded pins and attach the inspection cover (2).
markilux Handover Declaration For the users of vertical blinds and conservatora awnings
markilux
markilux awnings for exterior use conform to the standard EN 13561 for awnings and thus to the current technical requirements in relation to their construction and installation brackets.The wind resistance class the installation conforms to, is determined specifi cally by the type and number of fi xture brackets as well as the fi xture substrate being fi tted to.The awning may be used only up to the wind resistance class declared permissible by the installing company. This may differ from the wind resistance class specifi ed in the CE conformity mark.In accordance with its knowledge of local conditions and the type of installation it has carried out, the installing company shall inform the user as to whether the wind resistance class permitted by markilux has been met and shall document the actual wind resistance class met by the installation.Automatic control mechanisms are to be adjusted so that they react to the appropriate wind resistance class.
markiluxSchmitz-Werke GmbH & Co.KG
Hansestraße 87D-48282 Emsdetten
DIN EN 13561Blinds and awnings for exterior applications
wind resistance class 2markilux 710/810, 720/820, 725/825, 750/850, 730/830, 791/891,
740/840, 745/845, 893, 869/869 zip (depending on size),8500 and 8850
wind resistance class 3markilux 760/860, 620 zip, 660 zip, 680 zip, 689 zip,
869/869 zip (depending on size), 780/880, 8000,8000 with curved front, 8800/8800 zip, pergola 100/200
and pergola 110/210
wind resistance class 0 wind resistance class 1 wind resistance class 2 wind resistance class 3
Wind resistance class 0 corresponds either to performance criteria that we were not asked to meet or to those that have not been measured or to a product that does not fulfi l the requirements of wind resistance class 1.
The awning may remain extended up to a maximum of Beaufort force 4.
The awning may remain extended up to a maximum of Beaufort force 5.
The awning may remain extended up to a maximum of Beaufort force 6.
Defi nition according to Beaufort:
moderate breeze, moderate windThe wind moves twigs and smaller branches, lifts dust and loose paper.
Defi nition according to Beaufort:
fresh breeze, fresh windSmall deciduous trees begin to sway, white crests forms on seas
Defi nition according to Beaufort:
strong breezeLarge boughs move, umbrellas are diffi cult to keep under control, telephone wires "whistle" in the wind
Use only under supervision. The awning must be retracted if there is any wind.
wind speed5.5-7.4 m/s = 20-27 km/h = 12-16 mph
wind speed7.5-10.4 m/s = 28-37 km/h = 17-23 mph
wind speed10.5-13.4 m/s = 38-48 km/h = 24-30 mph
Date: Signature of fi tter:
Signature of user*:
* with your signature you confi rm that you have received a copy of the handover declaration!
The user was duly informed as the operation of the awning: yes no
Following documents have been handed to the user:• Operation manual yes no• Installation and setting instructions supplied by the motor, switch and control unit manufacturer(s) (if available) yes no
The awning may be used under the following conditions:Wind: X permissable up to wind resistance class = wind speed
Rain:permissable when the awning is fully extended
not permitted with an angle of inclination below 25% = 14°, measured from the horizontal plane
Danger of frost and snow: X not permitted
04/07/2012
markilux Handover Declaration For the users of vertical blinds and conservatora awnings
markilux
markilux awnings for exterior use conform to the standard EN 13561 for awnings and thus to the current technical requirements in relation to their construction and installation brackets.The wind resistance class the installation conforms to, is determined specifi cally by the type and number of fi xture brackets as well as the fi xture substrate being fi tted to.The awning may be used only up to the wind resistance class declared permissible by the installing company. This may differ from the wind resistance class specifi ed in the CE conformity mark.In accordance with its knowledge of local conditions and the type of installation it has carried out, the installing company shall inform the user as to whether the wind resistance class permitted by markilux has been met and shall document the actual wind resistance class met by the installation.Automatic control mechanisms are to be adjusted so that they react to the appropriate wind resistance class.
markiluxSchmitz-Werke GmbH & Co.KG
Hansestraße 87D-48282 Emsdetten
DIN EN 13561Blinds and awnings for exterior applications
wind resistance class 2markilux 710/810, 720/820, 725/825, 750/850, 730/830, 791/891,
740/840, 745/845, 893, 869/869 zip (depending on size),8500 and 8850
wind resistance class 3markilux 760/860, 620 zip, 660 zip, 680 zip, 689 zip,
869/869 zip (depending on size), 780/880, 8000,8000 with curved front, 8800/8800 zip, pergola 100/200
and pergola 110/210
wind resistance class 0 wind resistance class 1 wind resistance class 2 wind resistance class 3
Wind resistance class 0 corresponds either to performance criteria that we were not asked to meet or to those that have not been measured or to a product that does not fulfi l the requirements of wind resistance class 1.
The awning may remain extended up to a maximum of Beaufort force 4.
The awning may remain extended up to a maximum of Beaufort force 5.
The awning may remain extended up to a maximum of Beaufort force 6.
Defi nition according to Beaufort:
moderate breeze, moderate windThe wind moves twigs and smaller branches, lifts dust and loose paper.
Defi nition according to Beaufort:
fresh breeze, fresh windSmall deciduous trees begin to sway, white crests forms on seas
Defi nition according to Beaufort:
strong breezeLarge boughs move, umbrellas are diffi cult to keep under control, telephone wires "whistle" in the wind
Use only under supervision. The awning must be retracted if there is any wind.
wind speed5.5-7.4 m/s = 20-27 km/h = 12-16 mph
wind speed7.5-10.4 m/s = 28-37 km/h = 17-23 mph
wind speed10.5-13.4 m/s = 38-48 km/h = 24-30 mph
Date: Signature of fi tter:
Signature of user*:
* with your signature you confi rm that you have received a copy of the handover declaration!
The user was duly informed as the operation of the awning: yes no
Following documents have been handed to the user:• Operation manual yes no• Installation and setting instructions supplied by the motor, switch and control unit manufacturer(s) (if available) yes no
The awning may be used under the following conditions:Wind: X permissable up to wind resistance class = wind speed
Rain:permissable when the awning is fully extended
not permitted with an angle of inclination below 25% = 14°, measured from the horizontal plane
Danger of frost and snow: X not permitted
04/07/2012
Top Related