7/26/2019 Mechanical Considerations
1/36
MECHANICAL
CONSIDERATIONSIN
LINEPERFORMANCE
7/26/2019 Mechanical Considerations
2/36
Introduction
Electric power can be transmitted or distributed either by means ofunderground cables or overhead lines
The underground system is much more expensive than overheadsystem. Therefore, it has limited use for distribution purposes incongested areas where safety and good appearances are the main
considerations
In overhead lines bare conductors are used and air acts as theinsulation. The necessary insulation between the conductor can beprovided by adjusting the spacing between them.
Electric power has to be transmitted at high voltages for economicreasons so its dicult to provide proper insulation
7/26/2019 Mechanical Considerations
3/36
Factors to be considered
The successful operation of an overhead line greatly depends onthe mechanical design of the line so, the overhead line shouldhave good mechanical strength against worst probable weatheconditions
The overhead line is subjected not only to uncertain weatherconditions but also to other external interferences
7/26/2019 Mechanical Considerations
4/36
7/26/2019 Mechanical Considerations
5/36
7/26/2019 Mechanical Considerations
6/36
echanical !omponents of "verheadlines
# !onductors
# $upports
# Insulators
# !ross arms
# iscellaneous items
7/26/2019 Mechanical Considerations
7/36
!onductor
%igh electrical conductivity, %igh tensile strength in order to withstandmechanical stresses, &ow cost ,&ow speci'c gravity so that weight perunit volume is small
In standard conductors there is one central wire and round this,successive layers of wires containing (,)*,)+ wires , thus total number
of individual wires is n-n)/) Types 00!,000!,0!$1,0!01
7/26/2019 Mechanical Considerations
8/36
00! has a minimum conductivity of ().*2 I0!$. It has limited use intransmission lines and distribution side for long distances butextensively seen in urban areas where spans are short
The excellent corrosion resistance of aluminum has made 00! aconductor of choice in coastal areas.
0!$130luminium !onductor $teel 1einforced, a standard of theelectrical utility industry since the early )4556s, consists of a solid orstranded steel core surrounded by one or more layers of strands of)75 aluminium
0!$1 is available in a wide range of steel content 3 from 82 by weightfor the (9) stranding to :52 for the 598 stranding. Early designs of0!$1 such as (9), 598, 59)4, 7:9)4 and 7:98 strandings featured high
steel content, *(2 to :52, with emphasis on strength perhaps due tofears of vibration fatigue problems.
Today, the most used strandings are )+9), :798, 8*98, and +:9)4,comprising a range of steel content from ))2 to )+2. For themoderately higher strength 7:9)4, 7:98, and *(98 strandings, the steelcontent is *(2, *(2 and )2
7/26/2019 Mechanical Considerations
9/36
6201 "AAAC" 3 0 high strength 0luminium3agnesium3$ilicon 0lloy!able was developed to replace the high strength (9) 0!$1 conductors
"riginally called 000!, this alloy conductor o;ers excellent electricalcharacteristics with a conductivity of 7*.72 I0!$, excellent sag3tensioncharacteristics and superior corrosion resistance to that of 0!$1
0!01 combines )75 and (*5) aluminium alloy strands to provide atransmission conductor with an excellent balance of electrical andmechanical properties. This conductor consists of one or more layers of)753%)4 aluminium strands helically wrapped over one or more (*5)3
T+) aluminium alloy wires.
(*5) 0luminium 0lloy !onductor $teel 1einforced/ 3 Is an 0!$1 with th)75 aluminium wires replaced by (*5)3T+) aluminium alloy wire
00!$1 conductors have approximately :52 to (52 more strength thancomparable standard 0!$1 conductors of e
7/26/2019 Mechanical Considerations
10/36
!onductors and its dimensions
(i) For 132 KVlines
: 'Panther' ACSR having 7-strands of steel of dia 3!! "" and 3!Strands of Al#"ini#" of dia 3!! ""
(ii) for 22! KVlines
: '$e%ra' ACSR having 7-strand of steel of dia 31& "" and -Strands of Al#"ini#" of dia 31& ""
(iii) for !! KVlines
: *in '+oose' ACSR having 7-Strands of steel of dia 33 "" an-Strands of Al#"ini#" of dia 33 ""
7/26/2019 Mechanical Considerations
11/36
&ine $upports
7/26/2019 Mechanical Considerations
12/36
Insulators
=in Type insulator
$uspension Type insulator
$train Type insulator
$hac>le Insulator
7/26/2019 Mechanical Considerations
13/36
=in Type insulator
Pin Insulatoris earliest developed o!r!a# insulator, but stillpopularly used in power networ> up to ?@ system
0s the lea>age path of insulator is through its surface,it is desirable to increase vertical length of the insulator
surface area for lengthening lea>age path
These rain sheds or petticoats are so designed, that duringraining the outer surface of the rain shed becomes wet butthe inner surface remains dry and non3conductive. $o therewill be discontinuations of conducting path through the wet
pin insulator surface
7/26/2019 Mechanical Considerations
14/36
$uspension Type insulator
In higher voltage, beyond ?@, it becomes uneconomical to use pin inbecause siAe, weight of the insulator
In sus$!nsion insulatornumbers of insulators are connected form a string and the line conductor is carried by the bottom most Each insulator of a suspension string is called disc insulatortheir disc li>e shape
Each suspension disc is designed for normal voltage rating ))?@-%igher volta)7?@/, so by using di;erent numbers of discs, a suspension string can be mafor any voltage level
0s the current carrying conductors are suspended from supporting structure suspension string, the height of the conductor position is always less than theheight of the supporting structure. Therefore, the conductors may be safe fro
7/26/2019 Mechanical Considerations
15/36
$train Type Insulator
Bhen suspension string is used to sustain extraordinary tensile load of condreferred as string insulator
Bhen there is a dead end or there is a sharp corner in transmission line, thesustain a great tensile load of conductor or strain.
0 strain insulator must have considerable mechanical strength as well as theelectrical insulating properties.
7/26/2019 Mechanical Considerations
16/36
$hac>le Insulator
The sa%&l! insulatoror s$ool insulatoris usually used inlow voltage distribution networ>. It can be used both in
horiAontal and vertical position
The use of such insulator has decreasedrecently after increasing
the using of underground cablefor distributionpurpose
7/26/2019 Mechanical Considerations
17/36
E;ects on vibrations
0s the number of sub3conductors used in bundle increases, thesevibrations ,countermeasures and spacing6s of sub3conductors will alsoa;ect the electrical design
Thus a mechanical designer has to consider the tower dimensions,phase spacing6s, conductor height, sub3conductor spacing6s, etc. from
which the electrical designer has to commence his calculations ofresistance, inductance, capacitance, electrostatic 'eld, corona e;ects,and all other performance characteristics.
The sub3conductors in a bundle are separated by spacers of suitabletype, which bring their own problems such as fatigue to themselves an
to the outer strands of the conductor during vibrations
7/26/2019 Mechanical Considerations
18/36
# 0eolian vibrations and galloping are present for both single3and multi3conductor bundles, while the wa>e3induced oscillation is con'ned to abundle only
# $tandard forms of bundle conductors have sub3conductors ranging from*.7: to 7cm diameters with bundle spacing of :5 to 75 cm betweenadjacent conductors
# For E.%.@ Transmission, the number ranges from * to + sub3conductorsfor transmission voltages from :55 >v to )*55 >v, and up to )* or even)+ for higher voltages which are not yet commercially in operation.
# The charges on the sub3conductors are of the same polarity, there exist
electrostatic repulsion among them. on the other hand, since they carrycurrents in the same direction, there is electromagnetic attraction
7/26/2019 Mechanical Considerations
19/36
Factors for @ibrations C
7/26/2019 Mechanical Considerations
20/36
# !onductor Tensions
# $pan &ength
# !onductor $iAe
# Type of !onductor
# Terrain of line
# Direction of prevailing winds
# Types of $upporting clamp of conductors3insulator assemblies from thetower
# Tower type
# %eight of tower type of spacers and dampers
# The vegetation in the vicinity of the line
7/26/2019 Mechanical Considerations
21/36
Types of vibrations and
oscillations)/0E"&I0 @I10TI"*/G0&&"=IG
/ B0?E3IDH!ED "$!I&&0TI"$
7/26/2019 Mechanical Considerations
22/36
0eolian @ibration
B%E 0 $""T%J $T1E0 "F 0I1 =0$$E$ 0!1"$$0 !K&ID1I!0& $%0=E, $H!% 0$ 0 !"DH!T"1 "1"%$B, @"1TI!E$ -EDDIE$/ 01E F"1ED " T%E&EEB01D $IDE -0!? $IDE/. T%E$E @"1TI!E$0&TE10TE F1" T%E T"= 0D "TT" $H1F0!E$,0D !1E0TE 0&TE10TIG =1E$$H1E$ T%0T TED T"
=1"DH!E "@EET 0T 1IG%T 0G&E$ T" T%EDI1E!TI" "F T%E 0I1 F&"B. T%I$ I$ T%E E!%0I$T%0T !0H$E$ 0E"&I0 @I10TI"
7/26/2019 Mechanical Considerations
23/36
0eolian @ibration
Bhen a conductor is under tension and a comparatively steady wind blowsacross it small vortices are formed on the leeward side called ?arman@ortices
The fre
7/26/2019 Mechanical Considerations
24/36
# They also give rise to wave e;ects in which the vibration travels alongthe conductor su;ering reMection at points of di;erent mechanicalcharacteristics
# Thus dampers are designed to provide negative reMections to reduce
the wave amplitudes
# 0eolian vibrations are not observed at wind velocities in excess of *7>m9hour.
# Flexible spacers are generally provided which may or may not bedesigned to o;er damping.
# In cases where they are purposely designed to damp the sub3span
oscillations, they are >nown as spacer3dampers# The 0eolian vibrations depend upon the power imparted by the wind of
the conductor. the fre
7/26/2019 Mechanical Considerations
25/36
Galloping
Galloping of a conductor is a very high amplitude, low3frem9hour, which may normallythan that ree the form of wedi;erent locations on the span.
Galloping may not be a problem in a hot country li>e India where temperatures arabove freeAing in winter
7/26/2019 Mechanical Considerations
26/36
Ba>e3Induced "scillation
The wa>e3induced oscillation is peculiar to a bundle conductor, andsimilar to 0eolian vibration and galloping occurring principally in Matterrain with winds of steady velocity and low turbulence
The free3induced oscillation must be normally in therange *7 to (7 >m9hour.
Ba>e3induced oscillation, also called NMutter instabilityN, is caused whenone conductor on the windward side aerodynamically shields the leewardconductor
7/26/2019 Mechanical Considerations
27/36
# The oscillation occurs when the bundle tilts 7 to )7O with respect to aMat ground surface
# The conductor spacing to diameter ratio in the bundle is also critical
# If the spacing b is less than )7d, d being the conductor diameter, a
tendency to oscillate is created while for b9d P )7 the bundle is found tobe more stable
7/26/2019 Mechanical Considerations
28/36
Dampers and $pacers
7/26/2019 Mechanical Considerations
29/36
7/26/2019 Mechanical Considerations
30/36
7/26/2019 Mechanical Considerations
31/36
Twin $pacers
7/26/2019 Mechanical Considerations
32/36
7/26/2019 Mechanical Considerations
33/36
7/26/2019 Mechanical Considerations
34/36
$toc>bridge Damper
7/26/2019 Mechanical Considerations
35/36
$pacer !on'guration
7/26/2019 Mechanical Considerations
36/36
1EFE1E!E$
)/E&E!T1I!0& ="BE1 $K$TE$ K !.&.B0D%B0*/EQT10 %IG% @"&T0GE EGIEE1IG K 10?"$% D0$ EG0HD1E
Top Related