SERVICE MANUAL
LIFEPAK® 20
LIFEPAK 20eDefibrillator/Monitor
©2002-2016 Physio-Control, Inc.
3202007-005
LIF Table of Contents
Back Index Next Page
C
Device Description
Modes of Operation
Preventive Maintenance
Battery Maintenance
EPAK 20/20e Defibrillator/Monitor
Title Page
lick a Topic
Preface Safety
Performance Inspection Procedures
Troubleshooting
Replacement Procedures
LIFEPAK 20/20e Specifications
P Back Index Next Page
LIF Section Contents
P maintain, test, troubleshoot, and repair the IFEPAK 20e defibrillator/monitor (device).20 Defibrillator/Monitor Operating PAK 20e Defibrillator/Monitor Operating by physicians, clinicians, and emergency tions provide step-by-step instructions, as intenance.t. Text that indicates the name of a button, ssage, or screen overlay appears in all utton and SETUP menu.
cs:
ernual
ations
(Continued on next page)
revious Page Table of Contents
EPAK 20/20e Defibrillator/Monitor
reface This service manual describes how toLIFEPAK 20 defibrillator/monitor or LSeparate publications, the LIFEPAKInstructions (MIN 3200750) and LIFEInstructions (MIN 3205878), are usedcare providers. The operating instrucwell as operator-level testing and maNote: Hyperlinks appear in blue tex
menu, menu item, screen mecaps, for example, ANALYZE b
This section covers the following topi
TrademarksUsing Adobe Acrobat ReadNavigating Through the MaViewing the PIP ChecklistService Personnel Qualific
P Back Index Next Page
LIF Section Contents
Pion
revious Page Table of Contents
EPAK 20/20e Defibrillator/Monitor
reface (continued) Contacting Physio-ControlResponsibility for InformatDevice TrackingService InformationWarranty InformationConfiguration InformationGlossaryAcronyms
P Back Index Next Page
LIF Preface
Tr
OMBO are registered trademarks of
hock Advisory System are trademarks of
demarks of Adobe Systems Incorporated.tered trademarks.
f Tektronix Incorporatedred trademarks of Masimo Corporation.
1-4
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ademarks
LIFEPAK, FAST-PATCH, and QUIK-CPhysio-Control, Inc.CODE SUMMARY, REDI-PAK, and SPhysio-Control, Inc.Adobe and Acrobat are registered traFluke and Fluke Biomedical are regisTektronix is a registered trademark oMasimo, SET, and LNOP are registe© 2002–2016 Physio-Control, Inc.PN 3202007-005
Publication date: 03/2016
P Back Index Next Page
LIF Preface
U
AcRe
Acrobat Reader. The Adobe Reader can internet URL http://www.adobe.com/ssistance using the Adobe Reader ELP in the HELP menu.
Us left side of the screen. They enable you to e manual, similar to a table of contents. n, click the BOOKMARKS tab located to the
e desired topic. kmark topic indicates additional topics exist lick the plus sign to expand or collapse the
Us left of the screen to view miniature images through the pages and click an image to
1-5
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
sing Adobe Acrobat Reader
cessing Adobe ader Help
This service manual opens in Adobebe downloaded for free at the Adobeproducts/reader.html. For additional aprogram, access ACROBAT READER H
ing Bookmarks Bookmarks appear in a column on theeasily navigate to main sections of thTo view or hide the bookmarks columfar left of the screen. To jump to a bookmark topic, click thNote: A plus sign to the left of a boo
under that bookmark level. Cbookmarks.
ing Page View Click the PAGES tab located to the farof each page in the document. Scrolljump quickly to that page.
P Back Index Next Page
LIF Preface
N
link to jump to that topic. Click each page to return to your previous inting finger when positioned over a link. h page also provides helpful links. The
jump to the main table of contents for the
mp to the table of contents for the section
dex.
teps in a document, returning to each page
next page of the manual.
to the previous page of the manual.vigation bar above the main bar that ics.
Back
1-6
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
avigating Through the Manual
Blue text indicates a hyperlink. Click ain the navigation bar at the bottom oflocation. The pointer changes to a poA navigation bar at the bottom of eacnavigation bar includes:■ Click to
manual.
■ Click to juyou are currently viewing.
■ Click to jump to the in
■ Click to retrace your sin the reverse order visited.
■ Click to jump to the
■ Click to jump Some pages include an additional naprovides access to closely related top
Table of Contents
Section Contents
Index
Back
Next Page
Previous Page
P Back Index Next Page
LIF Preface
V
ance Inspection Procedure Checklist is
ing the file in Acrobat Reader.
1-7
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
iewing the PIP Checklist
The LIFEPAK 20/20e device Performincluded on this CD-ROM.You can view this document by open
P Back Index Next Page
LIF Preface
S
qualified and thoroughly familiar with the e familiar with and be able to read and must meet at least one of the following
th an emphasis in biomedical electronicswith an emphasis in biomedical electronics experience
1-8
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Personnel Qualifications
Service technicians must be properlyoperation of the device. They must bunderstand the service manual. Theyrequirements (or the equivalent):■ Associate of Applied Science, wi■ Certificate of Technical Training, ■ Equivalent biomedical electronics
P Back Index Next Page
LIF Preface
C
lands B.V.
1-9
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ontacting Physio-Control
Physio-Control, Inc.11811 Willows Road NortheastRedmond, WA 98052-2003 USATelephone: 1.425.867.4000Toll Free (USA only): 1.800.442.1142Fax: 1.425.867.4121Internet: www.physio-control.com
Physio-Control Operations NetherGaljoenweg 686222 NV MaastrichtThe Netherlands
Physio-Control Australia Pty LtdSuite 4.0115 Orion RoadLane CoveNSW 2066Australia
P Back Index Next Page
LIF Preface
R
thods required to maintain, test, and repair peration of the device. Qualified service ate operating instructions and this service anding of the use and maintenance of the
rs to ensure that the appropriate person(s) o the information in this service manual, used throughout the manual.
1-10
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
esponsibility for Information
This service manual describes the methe device. It does not address the opersonnel must consult the approprimanual to obtain a complete understdevice.It is the responsibility of our customewithin their organization has access tincluding any warnings and cautions
P Back Index Next Page
LIF Preface
D
ion requires defibrillator manufacturers and ir devices. If your device has been sold,
stroyed, or if it was not obtained directly e device-tracking coordinator at ting instructions for more information
1-11
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
evice Tracking
Device Tracking:
The U.S. Food and Drug Administratdistributors to track the location of thedonated, lost, stolen, exported, or defrom Physio-Control, please notify th1.800.426.4448. Refer to your operaconcerning device tracking.
!USA
P Back Index Next Page
LIF Preface
S
ny assembly in the device, the service information provided in the Preventive
ld inspect any device that has been ify that the device is operating within erformance Inspection Procedure (PIP), re acceptable.vice are limited to those items accessible at s and adjustments must be made by
ents at the subassembly level simplify help ensure correct device operation and mblies that require software may require ce representative. maintenance for your device, contact your In the USA, call Physio-Control Technical he USA, contact your local Physio-Control
1-12
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Information
Before attempting to clean or repair atechnician should be familiar with theMaintenance section of this manual.A qualified service technician shoudropped, damaged, or abused to verperformance standards listed in the Pand that the leakage current values aReplacement procedures for the dethe subassembly level. Replacementqualified service personnel. Replacemrepair and servicing procedures and calibration. Printed circuit board asseinstallation by a Physio-Control ServiTo obtain Physio-Control service andlocal service or sales representative.Support at 1.800.442.1142. Outside trepresentative.
P Back Index Next Page
LIF Preface
W
ided with the LIFEPAK 20 defibrillator/
MAg
purchase of this device does not convey the device with replacement parts that
this device, fall within the scope of one or vice.
1-13
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
arranty Information
Refer to the warranty statement provmonitor.
asimo® Use reement
No Implied License — Possession orany express or implied license to usewould, alone, or in combination with more of the patents relating to this de
P Back Index Next Page
LIF Preface
Bseful life.
e should be recycled according to national tions on disposing of this product or its sio-Control.com/recyclingbe clean and contaminant-free prior to
s – After using disposable electrodes, es for recycling.ce uses rechargeable Lithium-ion batteries. ctions provided in this service manual for as described. recycled according to national and local
1-14
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
attery Recycling Information Recycle the device at the end of its u
■ Recycling assistance – The devicand local regulations. For instrucaccessories, see http://www.Phy
■ Preparation – The device should being recycled.
■ Recycling of disposable electrodefollow your local clinical procedur
■ Recycling of batteries – The deviFollow local guidelines and instrudiscarding and recycling batteries
■ Packaging – packaging should beregulations.
P Back Index Next Page
LIF Preface
C
evices and options through the following
itor basic device with ECG
1-15
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
onfiguration Information
This service manual covers existing drevisions:■ LIFEPAK 20/20e defibrillator/mon■ Pacing option■ SpO2 option
P Back Index Next Page
LIF Preface
G
used throughout this service manual. AED) — The device uses an ECG analysis ise the device operator if it detects a m. For more information, refer to the Shock perating instructions.k waveform generated by the device. The ed by a positive current phase, followed by r duration and decreased magnitude. The biphasic truncated exponential (BTE).summary report that consists of a , and waveforms associated with certain
ement section in the operating instructions eport.
(Continued on next page)
1-16
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
lossary
The following are definitions of terms■ Automated external defibrillator (
Shock Advisory System™ to advshockable or nonshockable rhythAdvisory System section in the o
■ Biphasic technology — The shocbiphasic waveform is characteriza reverse current phase of shortewaveform pulse characteristic is
■ CODE SUMMARY™ report — A preamble, an event/vital signs logevents. Refer to the Data Managfor a sample CODE SUMMARY r
P Back Index Next Page
LIF Preface
Gystem (CPSS) — A feature that monitors LES for a potentially shockable rhythm.
DE indicator is on or the VF/VT ALARM is S button (manual mode). The CPSS hock Advisory System. For more visory System section in the operating
llation/ECG electrodes — An electrode fibrillation therapy to the patient.ion/ECG electrodes — An electrode system defibrillation therapy to the patient.
A combination lead tester/patient cardiac s designed for use in training clinical device.
(Continued on next page)
1-17
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
lossary (continued) ■ Continuous patient surveillance s
the patient ECG in LEADS or PADDCPSS is active when the AED MOselected after pressing the ALARMoperates in conjunction with the Sinformation, refer to the Shock Adinstructions.
■ FAST-PATCH® disposable defibrisystem that allows delivery of de
■ QUIK-COMBO® pacing/defibrillatthat allows delivery of pacing and
■ QUIK-COMBO patient simulator —rhythm simulator. The simulator ipersonnel in the operation of the
P Back Index Next Page
LIF Preface
G— A variant of the QUIK-COMBO pacing/tem. The system allows QUIK-COMBO e cable connection without removing the led pouch until needed.puterized ECG analysis system used to ore information, refer to the Shock
perating instructions.meter that checks the saturation of oxygen
o connect the test load to the patient
Agent — Software application that allows onfiguration and software updates. For System refer to internet: www.physio-
1-18
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
lossary (continued)
■ REDI-PAK™ preconnect system defibrillation/ECG electrodes syspacing/defibrillation/ECG electrodelectrodes from their air-tight sea
■ Shock Advisory System — A comdetect a shockable rhythm. For mAdvisory System section in the o
■ SpO2 — A noninvasive pulse oxiin arterial blood.
■ Test plug — An accessory used tconnector on the device.
■ LIFENET Asset, LIFENET Devicethe user to change device user cmore information about LIFENETcontrol.com
P Back Index Next Page
LIF Preface
Ad abbreviations used in this manual.
dvancement of Medical Instrumentationversionefibrillator
ciationtandards Institutexponential external body connection
direct cardiac connectionuscitationniturveillance system
or
(Continued on next page)
1-19
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
cronymsThe following is a list of acronyms an
Term DescriptionAAMI Association for the AADC Analog-to-digital conAED Automated external dAh Ampere hourAHA American Heart AssoANSI American National SBTE Biphasic truncated eBF Electrically isolated, BPM Beats per minuteCF Electrically isolated, CPR Cardiopulmonary resCPU Central processing uCPSS Continuous patient sDMM Digital multimeterDSP Digital signal process
P Back Index Next Page
LIF Preface
A
ronous receiver/transmitter
ervicee
l Commission
Alert Program
anufacturer
(Continued on next page)
1-20
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
cronyms (continued).Acronyms
Term DescriptionDUART Dual universal asynchECG ElectrocardiogramEMS Emergency medical sESD Electrostatic dischargESU Electrosurgical unitHR Heart rateIEC International ElectricaLCD Liquid crystal displayLED Light-emitting diodemmHg Millimeters of mercuryNHAAP National Heart AttackNSR Normal sinus rhythmOEM Original equipment mPC Personal computerPCB Printed circuit board
P Back Index Next Page
LIF Preface
A
on procedure
et computer
olatile random-access memory
rocedurerent
ia
1-21
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
cronyms (continued)
Term DescriptionPIP Performance inspectiPPM Pulses per minuteRISC Reduced instruction sRR Respiration rateRTC/NVRAM Real-time clock/non-vSSD Static-sensitive deviceTCP Test and calibration pVAC Volts, Alternating CurVF Ventricular fibrillationVT Ventricular tachycard
LIF Section Contents
P Back Index Next Page
S fety conventions, terms, and symbols used e. This information is intended to alert recautions in the care, use, and handling of
tions
EPAK 20/20e Defibrillator/Monitor
revious Page Table of Contents
22afety This section describes the general sain this service manual or on the devicservice personnel to recommended pthis medical device.
TermsGeneral Warnings and CauSymbols
P Back Index Next Page
LIF Safety
Te
ervice manual or on the various ize yourself with their definitions and
ill result in serious personal injury or death.es that could result in serious personal
es that could result in device or property
st for more efficient or convenient device mation or explanation concerning the
2-2
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
rms
The following terms are used in this sconfigurations of the device. Familiarsignificance.Danger: Immediate hazards that wWarning: Hazards or unsafe practic
injury or death.Caution: Hazards or unsafe practic
damage.Note: Points of particular intere
operation; additional inforsubject under discussion.
P Back Index Next Page
LIF Safety
G
nd cautions. Keep these warnings and he device. More specific warnings and ice manual and the operating instructions.
s up to 360 J of electrical energy. Unless rating instructions, this electrical energy may ttempt to operate or service this device unless f all controls, indicators, connectors, and
rmed by properly trained individuals. This rges accessible inside the device at any time –
efully for discharging the A13 Energy Storage
any portion of this device in water or other device or accessories. If the device is ever ove the batteries and disconnect ac power until
interconnected to each other can be a source e that all equipment is interconnected safely
(Continued on next page)
2-3
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
eneral Warnings and Cautions
The following are general warnings acautions in mind when working with tcautions appear throughout this serv
WARNINGShock hazard. The defibrillator deliverproperly used as described in the opecause serious injury or death. Do not athoroughly familiar with the function oaccessories.
Servicing of this device must be perfodevice may retain potentially lethal chaeven when off. Follow procedures carCapacitor.
Shock or fire hazard. Do not immerse fluids. Avoid spilling any fluids on theimmersed in water or other fluids, remthe device can be serviced.
Equipment or accessories improperly of ignition or cause a shock. Make sur
P Back Index Next Page
LIF Safety
G
trical shock, this equipment must only be tective earth.
or ECG/sync connector must be battery C power according to EN 60601-1.
ot service this device in the presence of en sources.
e directly above the patient. Place the device in tient should it fall from its shelf or other mount
ice may be damaged by mechanical or physical ropping. If the device has been abused,
ed service personnel.
2-4
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
eneral Warnings and Cautions (continued)
WARNINGShock hazard. To avoid the risk of elecconnected to a supply mains with pro
All equipment connected to the systempowered or electrically isolated from A
Possible fire or explosion hazard. Do nflammable gases, anesthetics, or oxyg
Patient hazard. Do not mount the devica location where it cannot harm the pa
CAUTIONPossible equipment damage. This devabuse such as immersion in water or dremove it from use and contact qualifi
P Back Index Next Page
LIF Safety
Sat may be used in this service manual or on nd accessories. Some symbols may not be ry country.
of type CF terminal
tected, type BF patient connection
connection
g instructions (symbol is black on white
g instructions
lt accompanying documents.
(symbol is black on yellow background)
ltage
rotective earth connection
(Continued on next page)
2-5
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ymbols The following list includes symbols thvarious configurations of the device arelevant to your device or used in eve
Defibrillation-pro
Defibrillation pro
Type BF patient
Consult operatinbackground)Consult operatin
Attention, consu
General warning
Warning, high vo
Safety ground. P
P Back Index Next Page
LIF Safety
S
nnector
l
l
ection to the ac mains)
nnection from the ac mains)
(Continued on next page)
2-6
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ymbols (continued)
Equipotential co
Positive termina
Negative termina
AC voltage
DC voltage
On (power: conn
Off (power: disco
Power on/off
Switch on
Switch off
[signal] Input
P Back Index Next Page
LIF Safety
S
t
or/data in
utton
ator shock
on screen
(Continued on next page)
2-7
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ymbols (continued)
[signal] Output
Sync in/ECG ou
System connect
HOME SCREEN b
Alarm off
Alarm on
Biphasic defibrill
Shock button
Shock count (x)
Joules
(x)
J
P Back Index Next Page
LIF Safety
S
n paddle
n paddle
rnal pacing
invasive pacing
arker
(Continued on next page)
2-8
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ymbols (continued)
Adult defibrillatio
Infant defibrillatio
Pace arrow, inte
Pace arrow, non
R-wave sense m
Event marker
Heart rate
Greater than
Less than
P Back Index Next Page
LIF Safety
S
nced
dicator
evice (SSD)
ity according to the European Medical 93/42/EECards Association certification for Canada tates
tion for Canada and the United States
ponent mark for Canada and the United
ity to ACA standards
(Continued on next page)
2-9
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ymbols (continued)
VF/VT alarm on
VF/VT alarm sile
Battery status in
Fuse
Static-sensitive d
Mark of conformDevice DirectiveCanadian Standand the United S
Intertek certifica
Recognized comStates
Mark of conform
P Back Index Next Page
LIF Safety
S
cable
kwise to unlock
te of manufacture)
used for placing orders
tem number
epresentative
wn: yyyy-mm-dd
ch code)
(Continued on next page)
2-10
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ymbols (continued)
Device to device
Turn countercloc
Manufacture (da
Serial number
Catalog number
Manufacturer’s i
Authorized EC r
Reorder number
Use by date sho
Single use only
Lot number (bat
YYYY
REF
LOT YYWW or YYMMDD
P Back Index Next Page
LIF Safety
Sf this product in the unsorted municipal
ispose of this product according to local www.physio-control.com/recycling for e proper disposal of this product.
a RoHS indicating the Environmentally riod (EFUP) denoting the number of years tance is likely to leak out into the
ripping water per IEC 60529
ces only
e, handle with care
ricts this device to sale by or on the order
er
2-11
(Continued on next page)
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ymbols (continued)
Do not dispose owaste stream. Dregulations. Seeinstructions on thSymbol for ChinFriendly Use Pebefore any subsenvironment.
Recycle this item
Protected from d
For USA audien
Fragile/breakabl
Federal law restof a physician
Protect from wat
!USA
P Back Index Next Page
LIF Safety
S
storage temperatures
atteries. Do not use NiMH batteries in this
2-12
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ymbols (continued)
Recommended
This end up
Use only Li-ion bdevice.
LIF Section Contents
P Back Index Next Page
DD
pics:
eatures, and Accessories
EPAK 20/20e Defibrillator/Monitor
revious Page Table of Contents
3evice escription
This section includes the following to
IntroductionPhysical Description and FOrdering Devices, SuppliesSystem Context DiagramsFunctional Description
P Back Index Next Page
LIF Device Description
In
Ab itor (device) is a complete, acute, cardiac-al and semiautomatic defibrillation e device enables the operator to deliver a the patient’s heart. Operators can plexity during normal operation.
En ated exponential (BTE) shock pulse for energy delivery is through self-adhesive G electrodes. When using these Es), internal circuitry continuously
electrodes and allows defibrillation only ttached to the patient. The user can select for energy delivery (for example, standard
3-2
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
troduction
out the Device The LIFEPAK 20/20e defibrillator/moncare response system with both manuoperation. When clinically indicated, thbrief, high-energy pulse of electricity topreconfigure the device to reduce com
ergy Delivery The device generates a biphasic truncdefibrillation. The standard method of QUIK-COMBO pacing/defibrillation/ECdisposable defibrillation electrodes (DDmeasures the impedance between thewhen the defibrillation electrodes are afrom a variety of optional accessories paddles or internal paddles).
P Back Index Next Page
LIF Device Description
In
MOp
off), the device enables the operator to e a charge sequence, and apply energy in hen the operator selects the VF/VT ALARM
s patient surveillance system (CPSS) able rhythm. A suspect rhythm alerts the
n message. The operator can then follow dministration of defibrillation therapy.
AE , the device uses the CPSS to monitor the A suspect rhythm alerts the operator with he operator may continue by pressing the ck Advisory System to analyze the ECG he operator can then follow locally ration of defibrillation therapy. For more visory System, refer to Appendix E in the
3-3
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
troduction (continued)
anual Mode eration
In manual mode (AED MODE indicatormanually select an energy level, initiateither direct or synchronized modes. Wfrom the ALARMS menu, the continuoumonitors the patient’s ECG for a shockoperator with a priority tone and screelocally established guidelines for the a
D Mode Operation In AED mode (AED MODE indicator on)patient’s ECG for a shockable rhythm.a priority tone and screen message. TANALYZE button, which allows the Shorhythm and make recommendations. Testablished guidelines for the administinformation about CPSS and Shock Adoperating instructions.
Back Index Next Page
LI Device Description
InDF
:
D) defibrillation manual mode
y and ECG electrodes
es of operation
data at each event stamps for eventsarted events for printout
at onceximetry (SpO2) readoutte readout
sense markerstion/ventricular tachycardia and sounds a
d diagnostic functions.
3-4
Previous Page Table of Contents Section Contents
FEPAK 20/20e Defibrillator/Monitor
troduction (continued)
evice Primary unctions
The device has four primary functions■ Defibrillation
– Manual or semi-automatic (AE– Synchronized cardioversion in– Leads-off detection for therap
■ Noninvasive pacing– Demand and nondemand mod
■ Capture patient information– Stores both patient and device– Real-time clock provides time– Provides operator review of st
■ Patient signal monitoring– Displays up to two waveforms– Displays a continuous pulse o– Displays a continuous heart ra– Displays waveform pace and – Monitors for ventricular fibrilla
warning alarm– Prints continuous ECG data
Service features include calibration an
P Back Index Next Page
LIF Device Description
In
As ase assembly and optional extension ules/PCBs:
l components:
4. Therapy PCB5. User Interface PCB6. OEM modules
7. System connector panel module8. Internal ac to dc power supply9. Internal battery10. Internal cables
4. Internal paddles5. Standard paddles
3-5
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
troduction (continued)
semblies The device consists of a three-piece cmodule that enclose the following mod
and the following OEM and mechanica
and the following attachments:
1. System Control PCB2. Patient Parameter PCB 3. Power module
1. Display2. Speaker3. User controls and indicators4. Printer 5. SpO2 acquisition6. Patient connector panel
1. ECG 3- or 5-wire cables2. QUIK-COMBO cable3. SpO2 cable
P Back Index Next Page
LIF Device Description
In
Depe
s 1 device with battery backup.ent connection. Therapy, SpO2, and CO2
ent connection.
3-6
Ite ms 20–29
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
troduction (continued)
vice Classifications r IEC 60601-1
Defibrillator—Externally powered ClasApplied parts—ECG is a Type CF patiare Type BF patient connections.Internal electrodes are a Type CF pati
ms 1–6 Items 7–13 Items 14–19 Ite
P Back Index Next Page
LIF Device Description
P
LIFr
, indicators and connectors shown below, click items bar at the bottom of the page.
11 15 1612 1413
17
24
18192021
23
25
22
29
28
27 26
(Continued on next page)
Items 20–29 Back to Illustration
3-7
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
hysical Description and Features
FEPAK 20/20e ont Panel
For information about the buttonsthe appropriate right arrow on the
123
4567
8 9 10
Items 7–13 Items 14–19
P Back Index Next Page
LIF Device Description
P ed)
LIFr(c
(Continued on next page)
or liquid crystal display (LCD) screen displays waveforms, status messages, setup menus,
s to activate user-defined events. — Press to return to the home screen of the ture you are configuring. Pressing this button specific screen; instead, it returns to the ode or event you are configuring.
ol — Press to print the CODE SUMMARY
to start and stop the printer. the ac power (line power) is connected, the
dy.
3-8
Ite Items 20–29 Back to Illustration
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
hysical Description and Features (continu
FEPAK 20/20e ont Panel ontinued)
Number Description
1 Display screen — Coloperating messages, and so forth.
2 EVENT control — Pres3 HOME SCREEN control
particular option or feadoes not take you to ahome screen for the m
4 CODE SUMMARY contrcritical event record.
5 PRINT control — Press6 AC Mains LED - When
AC mains light is stea
ms 1–6 Items 14–19
P Back Index Next Page
LIF Device Description
P ed)
LIFr(c
— Illuminates when the device enters nto the Service Log (accessed through the er to Troubleshooting for information about
r — Connection port for the electrically cable.r — Connection port for the pulse oximeter. Infrared connection port provides wireless
ata management devices (this feature is not lease).— When active (SPEED DIAL LED is on), turn ake a selection from the menu or overlay ; press to confirm your selection.lluminates when the SPEED DIAL is active.ress to activate and silence alarms.
(Continued on next page)
3-9
Ite Items 20–29 Back to Illustration
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
hysical Description and Features (continu
FEPAK 20/20e ont Panel ontinued)
Number Description
7 Service indicator LEDservice error codes iSERVICE menu). Refthe error codes.
8 ECG cable connectoisolated ECG patient
9 SpO2 cable connecto10 IrDA port connector —
communications to davailable with this re
11 SPEED DIAL selector (either direction) to mshown on the screen
12 SPEED DIAL LED — I13 ALARMS control — P
ms 1–6 Items 7–13
P Back Index Next Page
LIF Device Description
P ed)
LIFr(c
ress to access the OPTIONS menu.ector — Connection port for the following:O electrodes (standard)
H electrodes (with optional cable)lectrodes (optional)ult and pediatric paddles (optional)les (optional)
ddle (optional) audio voice prompts and alert tones.
ess to temporarily slow the pacing rate. Press to adjust the pacing current.s to select a pacing rate.
(Continued on next page)
3-10
Ite Back to Illustration
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
hysical Description and Features (continu
FEPAK 20/20e ont Panel ontinued)
Number Description
14 OPTIONS control — P15 Therapy cable conn
– QUIK-COMB– FAST-PATC– REDI-PAK e– Standard ad– Internal padd– Posterior pa
16 Speaker — Provides17 PAUSE control — Pr18 CURRENT control —19 RATE control — Pres
ms 1–6 Items 7–13 Items 14–19
P Back Index Next Page
LIF Device Description
P
LIFr(c o activate the pacer function.
activate the synchronized mode.o discharge the device. to charge the device.
Press to select the energy levels in
n the device on and off. Illuminates when
hange the ECG size.change the ECG lead. to activate the Shock Advisory System.
— Illuminates when device is in AED
3-11
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
hysical Description and Features (continued)
FEPAK 20/20e ont Panel ontinued)
Number Description
20 PACER control — Press t21 SYNC control — Press to22 SHOCK control — Press t23 CHARGE control — Press24 ENERGY SELECT control —
manual mode.25 ON control — Press to tur
the device is turned on.26 SIZE control — Press to c27 LEAD control — Press to 28 ANALYZE control — Press29 AED MODE indicator LED
mode.
P Back Index Next Page
LIF Device Description
P
LISi
Printer — Prints ECG waveforms, CODE SUMMARY reports, and related informationPrinter button — Opens printer door (for paper installation)
3-12
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
hysical Description and Features (continued)
FEPAK 20/20e de Panel
P Back Index Next Page
LIF Device Description
P
LIBa
nnector — Connection port for ac (line) arning - Shock hazard on Page 2-4.
ector — Connection port for RS-232 ce. See Warning - Shock hazard on
onnector. See Warning - Shock hazard .tud
3-13
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
hysical Description and Features (continued)
FEPAK 20/20e ck Panel
1 432
Number Description
1 AC power copower. See W
2 System connserial interfaPage 2-4.
3 ECG/Sync con Page 2-4
4 Grounding s
P Back Index Next Page
LIF Device Description
P
WBa
ts shown below. For additional information s, Supplies, and Training Tools in the he operating instructions.
QUIK-COMBO electrodes
3-lead ECG cable
OMBO therapy cable
(3-pack) ECG electrodes
pO2 sensor packot included with
Nellcor option)
LIF
LIF
Q
QUIK-COMBO test plug
LIF
S
3-14
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
hysical Description and Features (continued)
hat Is Shipped with a sic Device
A basic device includes the componenabout components, refer to AccessorieMaintaining the Equipment section of t
QUIK-C
Operating instructions
(3) rolls 50 mm printer paper S
(N
In-Service DVD
AC power cord
EPAK 20 defibrillator/monitor
Operational DVD
Service Manual
Quick GuideEPAK 20 defibrillator/monitor
uick Reference Card
EPAK 20 defibrillator/monitor
ervicing CD- ROM
P Back Index Next Page
LIF Device Description
O s
Th tions, supplies, and accessories that are av
It MIN CAT.LB
3313180-004 26500-0035023313187-004 26500-003504804700-003 11240-0000133308666-000 21300-0080758036503205874-002 26500-0019603202149-001 26500-001050
Q 3006570-007 11110-0000403202674-002 11996-000017
3201673-000 11113-000002
(Continued on next page)
3-15
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
rdering Devices, Supplies, and Accessorie
e following table (provided for reference) summarizes optional configuraailable. For ordering instructions, refer to Ordering Parts.
em DescriptionIFEPAK 20/20e defibrillator/monitorasic device Device with printer; includes:
■ LIFEPAK 20 operating instructions, English■ LIFEPAK 20e operating instructions, English■ 50-mm printer paper (package of 3)■ LIFEPAK 20e In-Service DVD Assembly■ Power cord■ LIFEPAK 20 Quick Guide, Clinical Training■ Accessory order form
UIK-COMBO ■ QUIK-COMBO therapy cables■ QUIK-COMBO electrodes with REDI-PAK™
preconnect system■ QUIK-COMBO test plug
P Back Index Next Page
LIF Device Description
O s (continued)
Yo template provided with the device. Place the uide to drill the holes for the screws that seNo lling the docking station.
It MIN CAT.S 3201655-003 11171-000007
3201655-001 11171-0000083201655-011 11171-0000173201655-010 11171-000016
E 3006218-02 11110-0000293006218-03 11100-000030800139-003 11100-000001
5 3200496-00 11110-0000663200496-01 11110-000067
S 3200936-013 11130-000037D 3201551-002 21330-000996
3-16
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
rdering Devices, Supplies, and Accessorie
u can install the docking station on any flat surface using the installation template where you want to install the docking station and use it as a g
cure the device.te: Ensure that the device has an adequate turning radius before insta
em DescriptionpO2 -option ■ LNOP® reusable adult finger sensor
■ LNOP SpO2 cable, 2.4 m (8 ft)■ LNCS reusable adult finger sensor■ LNCS SpO2 cable, 3.6 m (10 ft)
CG ■ 3-lead ECG cable (AHA)■ 3-lead ECG cable (IEC)■ ECG electrodes (package of 3)
-wire ECG -option ■ 5-wire ECG cable (AHA)■ 5-wire ECG cable (IEC)
tandard Paddles ■ Standard Paddles (Eng)ocking Station ■ Docking station and installation template
P Back Index Next Page
LIF Device Description
S
Fr how the device connects with external teries, and power devices.
(Continued on next page)
IK-COMBO rapy cable IK-COMBO
lectrodes) Standard paddles
AP
EX
STE
RN
UM
3-17
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ystem Context Diagrams
ont of Device The system context diagrams illustrateequipment, including accessories, bat
QUthe
(QUe
SpO2 cable
5-lead ECG cable
ECG electrodes pack
3-lead ECG cable
(3) rolls 50 mm printer paper
P Back Index Next Page
LIF Device Description
S
Ba
System connector
Grounding stud
3-18
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ystem Context Diagrams (continued)
ck of Device
AC power cord
ECG/sync connector
P Back Index Next Page
LIF Device Description
F
In tor is a medical device capable of monitoring features. In addition to defibrillation, manual defibrillation, and pO2 and ECG monitoring. This device
ple, a hospital or therapy center) and is n additional internal battery for use as a
ntended to provide service personnel with sign. Its purpose is to assist qualified o the subassembly level. Troubleshooting e factory is not recommended, nor is it
to provide the detail necessary to support
pages as you review the descriptions that
3-19
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description
troduction The LIFEPAK 20/20e defibrillator/monicombining a variety of therapeutic andautomatic defibrillation, semiautomaticnoninvasive pacing, the device offers Sshould be used indoors only (for exampowered by ac (line) power. There is abackup to ac power.The following functional description is ia basic understanding of the device deservice technicians in troubleshooting tbelow the subassembly level outside thwithin the scope of this service manualsuch repairs.Refer to the diagrams on the next two follow.
P Back Index Next Page
LIF Device Description
FSy w the descriptive text.
W01 Therapy
Connector
W02 Speaker
A04 Therapy PCB
A03 Power Module
A13 Capacitor
A14 Inductor
W11ECG Out/Sync InRS-232
7 ry
A09 AC Power Supply
A19 EMI Line Filter
B
S
I
CPU
Relay
Pacer
H-BridgePacer Supply
Cap Charger
Sonalert RS-232 DriversPower
Supplyr
Battery Charger
3-20
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
stem Block Diagram Click a link in the diagram below to vie
A01 System PCBA05 User Interface PCBA15
Keypad
A02 Patient Parameter PCB
W06 ECG Connector
A0Batte
W05 SpO2 Connector
A10SpO2 PCB
A06 OEM I/F PCB
A11 LCD
A08acklight
W04 peed Dial
W03rDA Port
A12Printer
DSPAudio Output
Paddles Pre-Amp
CPU
Data Bus
Companion Chip
Power Supply
DataBus
Power Supply
Power Switch
CPU
Data Bus
FPGA
Power Supply
Power Supply
Data Bus
CPUECG
Pre-AmpISO
Buffer
ISOP/S
UART
CPU
PoweMux
P Back Index Next Page
LIF Device Description
F
A0PC
es the central control for the device. A C) processor, along with a real-time clock al processing unit (CPU). A companion faces required within the device, including ication ports. The data bus provides high-1 System Control PCB and other PCBs
tem Control PCB are as follows:em Control PCB uses SW_VBatt A04 Therapy PCB to originate five power B as follows:
log ECG out, audio output circuitry, and
essor memory, companion chip and CPU
al signal processor processor chip
analog power for the paddles pre-amp
(Continued on next page)
3-21
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
1 System Control B
The A01 System Control PCB providreduced instruction set computing (RISand digital memory, serve as the centrchip provides most of the discrete interthe RS-232 and IrDA external communspeed communication between the A0within the device. The major subsystems on the A01 Sys■ Power Supplies — The A01 Syst
(switched battery voltage) from thesupplies for use throughout the PC– ±5 V analog power for the ana
bus control– +3.3 V logic power for the proc
I/O– +2.5 V logic power for the digit– +2.0 V logic power for the CPU– Patient-isolated ±10 and ±5 V
P Back Index Next Page
LIF Device Description
F
A0PC
he paddles ECG pre-amplifier performs th filtering, and ECG sampling by means ADC) for the ECG signal received via the ADC are fed into the digital signal ring. Electrostatic discharge (ESD) and d for these signals as they pass through atient impedance is also measured using
The DSP completes ECG digital signal andwidth, acceptable for Shock Advisory ssing, and continuous ECG storage by ides the necessary audio processing for digital audio signals to the audio output
t circuitry provides digital-to-analog alog drive circuitry for the audio tones and fication are provided to drive the case of the device.
3-22
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
1 System Control B (continued)
■ Paddles ECG Pre-Amplifier — Tpatient-isolation, low-pass bandwidof an analog-to-digital conversion (therapy paddles. Results from the processor (DSP) for additional filtedefibrillation protection are providethe A04 Therapy PCB. Change in pa 57.1 kHz carrier.
■ Digital Signal Processor (DSP) —processing to a diagnostic quality bSystem, heart rate algorithm procethe CPU. In addition, the DSP provvoice prompts and tones, providingcircuitry.
■ Audio Output — The audio outpuconversion, filtering, and power anvoice prompts. Up to 2 W of ampliW02 Speaker located on the front
P Back Index Next Page
LIF Device Description
F
A0PC
ects ECG and SpO2 patient data, with the d provides preprocessed data to the algorithms, alarm control, operator rithms performed on the data before it is
nclude leads-off detection and internal sor (DSP) with digital memory makes up
performs these algorithms. System Control PCB through the data
tient Parameter PCB are as follows: nt Parameter PCB uses switched power power from the A07 Battery to originate e throughout the PCB as follows: CPU digital signal processor and memory A06 OEM Interface PCB drive the ECG pre-amp
(Continued on next page)
3-23
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
2 Patient Parameter B
The A02 Patient Parameter PCB collexception of the paddles ECG data, ansystem controller for AED and R-wavedisplay and printout, and storage. Algosent to the A01 System Control PCB ipacer detection. A digital signal procesthe central processing unit (CPU) thatCommunication is provided to the A01bus. The major subsystems on the A02 Pa■ Power Supplies — The A02 Patie
from the A04 Therapy PCB with dcthree power supply voltages for us– +3.3 V logic power to drive the– +5 V analog power to drive the– ±5 V patient-isolated supply to
P Back Index Next Page
LIF Device Description
F
A0PC
re-amplifier performs the function of th filtering, and ECG sampling through
DC) for the ECG signal received through gnals are passed over the isolation barrier rocessing. The ECG pre-amplifier section G input.
A0 sponsible for selecting the best available s/PCBs in the system from the available built-in memory makes up the CPU. Therapy PCB through a serial interface. wer Module are as follows: er Module uses ORed_VBatt (battery the A09 AC Power Supply Module) to s for use throughout the PCB as follows:PU microcontroller and memory
the power pump for the RS-232 driver
(Continued on next page)
3-24
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
2 Patient Parameter B (continued)
■ ECG Pre-Amplifier — The ECG ppatient-isolation, low-pass bandwidthe analog-to-digital conversion (Athe W06 ECG Connector. Digital siinto the DSP for additional signal psupports either 3-wire or 5-wire EC
3 Power Module The A03 Power module is primarily resource to power the rest of the modulepower sources. A microcontroller with Communication is provided to the A04The major subsystems on the A03 Po■ Power Supplies — The A03 Pow
voltage ORed with dc power from originate two power supply voltage– +5 V logic power to drive the C– + 3.3 V analog power to drive
circuits
P Back Index Next Page
LIF Device Description
F
A0(c
itches battery power in and out of VBatt, d load draw within the device. This circuit
CPU and provides the current voltage Power Supply Module to the CPU. The ac power to battery power if the voltage dly. Low voltage is detected by the broadcast to the other PCBs through the es.
fibrillator/monitor) — The battery charger ned specifically to support the A07 NiMH H batteries are not designed for trickle
pply Module keeps track of the amount of g from battery power. Charging is ents and periodically when the batteries ccur while the unit is powered on or while on need. The battery charger is designed lly in less than two hours.
(Continued on next page)
3-25
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
3 Power Module ontinued)
■ Power Mux — The power mux swdepending on power availability anis under supervisory control of thefrom the A07 Battery and A09 AC circuit automatically switches fromfrom the ac power supply falls rapiA09 AC Power Supply Module anddevice internal communication bus
■ Battery Charger (LIFEPAK 20 deis a constant current charger desigBattery selected for the device. NiMcharging, so the A09 AC Power Sutime the device has been operatinperformed following high-use incidare not in high use. Charging can othe unit is powered off, depending to charge the internal battery, usua
P Back Index Next Page
LIF Device Description
F
A0(c
fibrillator/monitor) — The battery charger ge charger designed specifically to
y selected for the device. Li-ion batteries g, so the A09 AC Power Supply Module tate-of-charge and, when it drops below harging of the battery (provided the
° C). Charging can occur while the device is powered off, depending on need. The cally charge the internal battery in less powered off and AC power is applied.io tone generator located on the power evice is turned off while not connected to
nal A07 Battery). This ac loss alert alarm setup is provided to temporarily disable
ce for shipment.nal originates on the A01 System Control
signal levels to ±12 V prior to the system
3-26
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
3 Power Module ontinued)
■ Battery Charger (LIFEPAK 20e deis a constant current-constant voltasupport the A07 Lithium Ion Batterare not designed for trickle charginkeeps track of the Li-ion battery's s85%, the battery charger initiates ctemperature is between 0° and 50is powered on or while the device battery charger is designed to typithan four hours when the device is
■ Sonalert — The sonalert is an audmodule that warns the user if the dac power (which depletes the intercan be turned off. A shipping modethis feature when packing the devi
■ RS-232 Drivers — The RS-232 sigPCB. The RS-232 drivers shift theconnector output.
P Back Index Next Page
LIF Device Description
F
A0 cing and defibrillation therapy features. he A04 Therapy PCB and the remainder microprocessor and digital memory PU) that manages communication with
rapy PCB are as follows: apy PCB uses SW_VBatt (switched er Module to originate five power supply B as follows:PU microprocessor and memorycing and therapy drive circuitwer for the pacing and therapy circuitsower for the pacing and therapy circuitsower for the pacing and therapy circuits
(Continued on next page)
3-27
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
4 Therapy PCB The A04 Therapy PCB controls the paThe primary communication between tof the device is through the data bus. Amake up the central processing unit (Cthe A01 System Control PCB.The major subsystems on the A04 The■ Power Supplies — The A04 Ther
battery voltage) from the A03 Powvoltages for use throughout the PC– +5 V logic power to drive the C– ±15 V analog power for the pa– Patient-isolated 5 V analog po– Patient-isolated 15 V analog p– Patient-isolated 30 V analog p
P Back Index Next Page
LIF Device Description
F
A0(c
is a control circuit that detects the ON r Interface PCB or a timer event from the r up the device. This portion of the ll times, with very low quiescent current detected, this circuit switches VBatt wer) provided by the A03 Power Module e. Low Battery (Battery Fail) is detected to other PCBs if battery voltage falls normal operation is no longer feasible.is a high-voltage, patient-isolated circuit citor to the correct voltage for biphasic trol is provided by the CPU, and capacitor U for feedback. The cap charger is imum charge rates and to automatically when low battery voltage is detected.r power supply is a patient-isolated circuit citor up to the correct voltage for pacing. d voltage regulation is maintained locally voltage is provided back to the CPU for cuitry.
(Continued on next page)
3-28
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
4 Therapy PCB ontinued)
■ Power Switch — A power switch button selection from the A05 UseA01 System Control PCB to poweA04 Therapy PCB is powered at adraw. When a power-on request is(battery and/or ac converted dc poto the remaining PCBs in the devicand a discrete signal is broadcast rapidly or reaches the point where
■ Cap Charger — The cap charger that charges the A13 Energy Capadefibrillation (2 to 360 joules). Convoltage is provided back to the CPdesigned to nominally provide maxscale back to slower charge rates
■ Pacer Power Supply — The pacethat charges the A13 Energy CapaControl is provided by the CPU, anwithin the pacer supply. Capacitor control through the cap charger cir
P Back Index Next Page
LIF Device Description
F
A0(c
ient-isolated circuit that creates the combination of silicon controlled rectifiers ransistors (IGBT) are used to place a e across the patient load, followed defibrillation pulse. The defibrillation
y and W01 Therapy Connector assembly e outside of the device. lated circuit that creates the pacing e circuitry is used to support the pacer by ibrillation Capacitor. A current drive is nt provided to the patient during pacing. t isolation from the pacing and se. The relay is closed when the pacing closed until the pacing current is set back
3-29
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
4 Therapy PCB ontinued)
■ H-Bridge — The H-Bridge is a patbiphasic defibrillation waveform. A(SCR) and insulated gate bipolar tpositive-oriented defibrillation pulsimmediately by a negative-orientedpulse is delivered through the relato the external therapy cable on th
■ Pacer — The pacer is a patient-isowaveform. A portion of the H-Bridgproviding energy from the A13 Defused to control the amount of curre
■ Relay — The relay provides patiendefibrillation circuitry when not in ucurrent is set above zero and staysto zero.
P Back Index Next Page
LIF Device Description
F
A0 esponsible for the presentation of the d to the printer, and for receiving all user een the UI PCB and the remainder of the processor and digital memory make up with the A01 System Control PCB. The onnection between the A05 UI PCB and
PCB are as follows: CB uses SW_VBatt (switched battery B to originate four power supplies for use
A11 Liquid Crystal Display (LCD) and the
processor and memory-programmable gate array
(Continued on next page)
3-30
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
5 User Interface PCB The A05 User Interface (UI) PCB is racquired data to the screen display aninput. The primary communication betwdevice is through the data bus. A RISCthe CPU that manages communicationW18 UI Flex Cable provides physical cthe A02 Patient Parameter PCB.The major subsystems on the A05 UI ■ Power Supplies — The A05 UI P
voltage) from the A04 Therapy PCthroughout the PCB as follows:– +3.3 V logic power to drive the
A12 Printer– +3.3 V logic power for the CPU– +2.5 V logic power for the field
P Back Index Next Page
LIF Device Description
F
A0(c
(FPGA) — The Field-Programmable Gate e between the CPU and all the user orks in conjunction with the CPU to A11 Display, the data and strobe signals try for the keypad LEDs. The FPGA d switch matrix and W4 Selector into e CPU. ary user input control for the device. It omes, which are located on the rear side er keypad cover that attaches to the front
through holes in the front case and he domes when pressed by the user. The PGA and sent to the CPU for processing. ze the ON switch. It passes the signal to
A0MCo
s power to and collects SpO2 data from tion is to provide patient isolation between evice design. In addition, it provides pO2 module.
(Continued on next page)
3-31
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
5 User Interface PCB ontinued)
■ Field-Programmable Gate ArrayArray (FPGA) provides the interfacinterface peripherals. The FPGA wprovide the 1/4 VGA signals to theto the A12 Printer, and drive circuiconverts the inputs from the keypadigital words that can be read by th
■ Keypad — The keypad is the primconsists of two parts, the keypad dof the A05 UI PCB, and the elastomcase. The keypad domes protrudeenable the key covers to activate tkey presses are decoded by the FThe A05 UI PCB does not recognithe A04 Therapy PCB.
6 OEM and echanical mponents PCB
The A06 OEM Interface PCB providethe A10 SpO2 Module. Its primary functhe SpO2 module and the rest of the dphysical mounting provisions for the S
P Back Index Next Page
LIF Device Description
F
A0MCo(c
M PCB are as follows: Interface PCB uses power from the vide the 5 V power for the A10 SpO2
RT and ISO buffers provide patient received from the A10 SpO2 Module and rameter PCB.
A0 r, the A07 Battery is a minimum 2.7 Ah , NiMH battery that is used as an internal
is not available. This technology was er-storage ratio and low maintenance rt, non-trickle, constant current charger ule when the device is connected to ac
aces directly with the A03 Power Module. tery well section of the bottom case. A open the battery door, located on the
/monitor.
(Continued on next page)
3-32
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
6 OEM and echanical mponents PCB
ontinued)
The major subsystems on the A06 OE■ Power supplies — The A06 OEM
A02 Patient Parameter PCB to proModule.
■ UART and ISO buffers — The UAisolation for the serial data signalsroutes them to the A02 Patient Pa
7 Battery On the LIFEPAK 20 defibrillator/monito(2.560 Ah per IEC 61951-2:2011), 12 Vbackup power source when ac power selected due to its light-weight-to-powfeatures. NiMH batteries require a smathat is provided by the A03 Power Modpower. The battery wire harness interfThe battery is contained within the batsmall-bladed screwdriver is required tobottom of the LIFEPAK 20 defibrillator
P Back Index Next Page
LI Device Description
F
A0(c
itor, the Li-ion battery technology was H, but they are even lighter in weight.
rrent-constant voltage charger that is hen the device is connected to ac power.
A0PC
power to the internal fluorescent backlight _VBatt is provided to the A08 Backlight
ce PCB. The output of the inverter is er to the internal A11 Active Display er for the LED A11 Display has an output current of 24 mA dc
A0M
is a 60-Watt OEM power supply, designed erting 120/240 Vac (60/50 Hz) input signals ply provides power to the A03 Power
in the device. The 12 Vdc output from the ed into the SW_VBatt (switched battery y PCB. The A03 Power Module sits above ly into the ac power supply’s power le and the ac power supply are held ssembly bracket.
3-33
revious Page Table of Contents Section Contents
FEPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
7 Battery ontinued)
On the LIFEPAK 20e defibrillator/monselected for the same reasons as NiMLi-ion batteries require a constant cuprovided by the A03 Power Module w
8 Backlight Inverter B
The A08 Backlight Inverter providesin the A11 Active Display. Filtered SWInverter through the A05 User Interfa1000 to 1500 RMS, open-circuit powbacklight. The 3308907 backlight drivaverage output voltage of 22Vdc and
9 AC Power Supply odule
The A09 AC Power Supply Moduleto meet IEC 60601-1 standards, convto nominal 12 Vdc. The ac power supModule for routing to the other PCBsac power supply is directly diode ORvoltage) to power on the A04 Therapthe ac power supply and plugs directconnector. Both the A03 Power Modumechanically in place by the power a
P Back Index Next Page
LIF Device Description
F
A1 simo MS-5, MS-11 or MS-2011 oximetry erforms all functions related to oxygen sor drive. Measurement results are
Interface PCB to the A02 Patient is combined with the patient ECG data CB for display processing and storage. he A06 OEM Interface PCB.
A1Le
.5 cm (5.7-inch) (measured diagonally) wide by 240 high pixel array. The display ainst the front case by a sheet metal display features full-color, high-lity, and is fully visible in bright-light ns). The A11 Active Display also contains -light situations. The updated A11 LED 08 backlight driver module 3308907.
A1 stepper motor-driven recorder. The printer m the A05 User Interface PCB, converts rive signals to perform the “muscle” part
ignals derived from the paper supply PCB.
3-34
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
0 SpO2 Module The A10 SpO2 Module can be the Mamodule. This patented OEM module psaturation measurement, including senpassed serially through the A06 OEM Parameter PCB where the SpO2 data and sent to the A01 System Control PThe SpO2 module mounts directly to t
1 Active Display/ns
The A11 Active Display measures 14and uses 1/4 VGA protocol with a 320has a protective lens, held in place agbracket, and an elastomeric seal. Thisbrightness, wide-viewing-angle capabisituations (up to direct sunlight operatioan internal backlight for visibility in lowdisplay 3309555 requires the use of A
2 Printer Module The A12 Printer Module is a 50 mm, receives serial data and commands frothe print data, and controls the motor-dof printing. The printer returns status ssensor and printer door to the A05 UI
P Back Index Next Page
LIF Device Description
F
A1 llized film capacitor used for energy nergy for both pacing and defibrillation e energy capacitor is calculated during The nominal value is 196 F. The energy device is turned off. Energy is provided to efibrillation therapy through the A14 r mounts above the A04 Power PCB by om the energy capacitor connect directly
A1 s an internal dump load to dissipate r. Energy is removed (dumped) from the is turned off and, during operation, when extended period of time. The inal 5 ohm load in the energy delivery stack bracket. Wires from the
y to connectors on the A04 Therapy PCB.
3-35
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
3 Energy Capacitor The A13 Energy Capacitor is a metastorage. The energy capacitor stores etherapies. The actual capacitance of ththe defibrillation calibration procedure.on the capacitor is removed when the the A04 Therapy PCB for pacing and dInductor Resistor. The energy capacitomeans of a capacitor support. Wires frto the A04 Therapy PCB.
4 Inductive Resistor The A14 Inductive Resistor is used aenergy from the A13 Energy CapacitoA13 Energy Capacitor when the deviceenergy remains on the capacitor for anA14 Inductive Resistor provides a nompath. The inductor mounts to the boardA14 Inductive Resistor connect directl
P Back Index Next Page
LIF Device Description
F
A1 the common device controls (those not umber of keys on this keypad varies, a specific device.
A1Fi
des input current overload and tection for the device. The filter is a potted nts (inductors and capacitors), with in-line . The A19 AC Input Power Filter is nts in IEC 60601-1.
WCo
bly provides a patient connection port or pacing therapeutic energies. The e attachment of all available electrode pacing/defibrillation/ECG electrodes, pediatric paddles), and internal paddles py Connector mounts directly to the s directly into the A04 Therapy PCB at otrudes through a hole in the front case to various external cable options.
g LIFEPAK 12 defibrillator/monitor l adult paddles with posterior
3-36
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
5 Elastomer Keypad The A15 Elastomer Keypad displaysavailable using the SPEED DIAL). The ndepending on the features installed in
9 AC Input Power lter
The A19 AC Input Power Filter provielectromagnetic interference (EMI) promodule containing passive filter elemefuses in both the line and neutral leadsdesigned to meet the safety requireme
01 Therapy nnector Assembly
The W01 Therapy Connector Assemused for delivery of either defibrillationstandard and premium models allow thaccessories, including QUIK-COMBO external standard paddles (with built-inwith discharge control. The W01 Therabottom case and the wire harness plugJ13 and J14. The therapy connector prprovide user access for connecting theNote: The device supports all existin
accessories (including externaattachments).
P Back Index Next Page
LIF Device Description
F
W to deliver device tones and voice prompts, M W02 Speaker is a small, compact, low-
one-watt output with a frequency ut to the speaker is from the audio power B. The speaker is mounted directly on
rness plugs into the W25 Speaker
W(Ir
rovide high-speed wireless devices. The OEM W03 IrDA port ions with asynchronous serial rates up to ted directly on the bottom case and the System Control PCB at J08. An infrared se directly in front of the IrDA port. The ed so that direct communications can ceiver held by an operator or placed on a
3-37
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
02 Speaker Assembly The W02 Speaker Assembly is used including warnings and alarms. The OEprofile speaker capable of producing aresponse from 300 to 7000 Hz. The inpamplifier in the A01 System Control PCthe front case and the speaker wire haHarness Extension Cable.
03 Infrared Data DA) Assembly
The W03 IrDA Assembly is used to pcommunications to data management supports IrDA version 1.1 communicat4 Mbits/second. The IrDA port is mounflex circuit connects directly to the A01lens is molded into the device front caIrDA port and front case lens are aligneasily be made with a portable data retable.
P Back Index Next Page
LIF Device Description
F
WAs
otary data entry device mounted on the ront case. It is used to control menu s that are not supported directly by hard cts rotation (in either a clockwise or es (clicks), and then passes this 32 for user-input decoding.
W connecting point for the external SpO2 d on the bottom case of the device, and A10 SpO2 Module.
W connection point for the standard 3-lead or onnector is mounted on the bottom case rness connects directly with the A05
ible with the 10-wire patient ECG cable, as a 5-wire cable.
WDi
rovides a capacitor discharge point by t pin 5 of J02.
3-38
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
04 Speed Dial sembly
The W04 Speed Dial Assembly is a rLIFEPAK 20/20e defibrillator/monitor faccess and selection for user functionkeys on the keypad. The selector detecounterclockwise direction) and pressinformation on to the A05 UI PCB at J
05 SpO2 Assembly The W05 SpO2 Assembly provides acable. The SpO2 connector is mountethe flex circuit connects directly to the
06 ECG Connector The W06 ECG Connector provides a 5-wire patient ECG cables. The ECG cof the device, and the attached wire haPatient Parameters PCB at J23. Note: The ECG connector is compat
but the device will only operate
07 Capacitor scharge Cable
The W07 Capacitor Discharge Cable pconnecting to the A04 Therapy PCB a
P Back Index Next Page
LIF Device Description
F
W r, the W08 Battery Cable connects the The cable is hardwired to the A03 Power the A07 Battery at J85.tor, the W08 Battery Cable connects the odule at J50.
WTh
PCB Cables connect the A03 Power is a replaceable cable that connects to e A03 Power Module at J41. r, W10 is hardwired to the A03 Power py PCB at J17.
tor, W10 connects to the A04 Therapy ule at J51.
WCa
onnect the ECG sync connector and the odule at J47.
W grounding path for the Speed Dial.
3-39
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
08 Battery Cable On the LIFEPAK 20 defibrillator/monitoA07 Battery to the A03 Power Module.Module and the other end connects toOn the LIFEPAK 20e defibrillator/moniA07 Battery at J85 to the A03 Power M
09/W10 Power to erapy PCB Cables
The W09 and W10 Power to Therapy Module to the A04 Therapy PCB. W09the A04 Therapy PCB at J16 and to thOn the LIFEPAK 20 defibrillator/monitoModule and connects to the A04 TheraOn the LIFEPAK 20e defibrillator/moniPCB at J17 and to the A03 Power Mod
11 ECG Sync/System bles
The W11 ECG Sync/System Cables csystem connector to the A03 Power M
12 Grounding Cable The W12 Grounding Cable provides a
P Back Index Next Page
LIF Device Description
F
W e A09 AC Power Supply Module at J02 d connection) for the LIFEPAK 20 LIFEPAK 20e defibrillator/monitor.
W he A05 UI PCB at J34 with the A03 Power
WCa
cts the A11 LCD Display PCB at CN1 with
WCa
der connects the A11 LCD Display PCB at at CN2.
WCa
nects the A08 Backlight Inverter PCB at
W 02 Patient Parameters PCB at J21 and
3-40
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
13 AC Power Cable The W13 AC Power Cable connects thwith the A03 Power Module (hard-wiredefibrillator/monitor, and at J49 for the
14 Printer Flex Cable The W14 Printer Flex Cable connects tModule at J45 and the A12 Printer.
15 LCD to UI PCB ble
The W15 LCD to UI PCB Cable connethe A05 UI PCB at J36.
16 Display Jumper ble Extender
The W16 Display Jumper Cable ExtenP77 to the A08 Backlight Inverter PCB
17 Backlight Inverter ble
The W17 Backlight Inverter Cable conP74 to the A05 UI PCB at J37.
18 UI Flex Cable The W18 UI Flex Cable connects the AJ22 to the A05 UI PCB at J31.
P Back Index Next Page
LIF Device Description
F
WCa
les provide grounding paths for various
WEx
Cable connects the W02 Speaker 5.
3-41
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
unctional Description (continued)
19 – W24 Grounding bles
The W19 through W24 Grounding Cabdevice components.
25 Speaker Harness tension Cable
The W25 Speaker Harness ExtensionAssembly to the A01 System PCB at J
LIF Section Contents
P Back Index Next Page
MO
ates in one of five modes. Choose from the particular operating mode.
ation
EPAK 20/20e Defibrillator/Monitor
revious Page Table of Contents
55odes of peration
When the device is turned on, it operfollowing links to learn more about a
Manual ModeAED ModeSetup ModeSaving the Setup ConfigurService ModeInservice Mode
P Back Index Next Page
LIF Modes of Operation
M
Tuin
rmine when to deliver a shock. anual mode (the default is AED mode):
ct MANUAL MODE.UAL MODE submenu.
able power-on options.
and then reset to AED mode by pressing tional manual mode reprompts or wer has been cycled.
scriptionanual mode; direct access between AED odes.
ED mode; direct access between AED odes.
ED mode; confirmation required to enter .ED mode; passcode required to enter .
(Continued on next page)
4-2
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
anual Mode
rning On the Device Manual Mode
Manual mode enables the user to deteTo configure the device to turn on in m1. Display the SETUP menu and sele2. Select MANUAL ACCESS in the MAN
3. Select the DIRECT option. The following table shows all the avail
If the device is placed in manual modethe ANALYZE button, there are no addipasscode requests until the device po
Mode/Response Response DeManual/Direct Turns on in m
and manual mAED/Direct Turns on in A
and manual mAED/Confirmed Turns on in A
manual modeAED/Passcode Turns on in A
manual mode
P Back Index Next Page
LIF Modes of Operation
M
Stfro
device is turned on, the device is in AED
ssing the MANUAL button on the lower left
s:
YZE button or cycle the device power.nual mode does not restart AED mode
4-3
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
anual Mode (continued)
arting Manual Mode m AED Mode
If the AED MODE LED is on when the Mode. To enter manual mode:■ Open the door (if installed) by pre
corner of the door.-OR-
■ Press one of the following button– ENERGY SELECT– CHARGE– PACER– LEAD
To restart AED mode, press the ANAL
Note: Closing the door when in maoperation.
P Back Index Next Page
LIF Modes of Operation
A
device automatically evaluates the patient ded and prompts the user to press the
rn on in manual mode, if desired. the SETUP menu and select AED MODE. otocol, voice prompts, ECG display, CPR cription of the options available, refer to the operating instructions.
D mode, opening the door on the device s the device in manual mode. Closing the de operation. To restart AED mode, press
power.
4-4
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ED Mode
In AED mode (the default setting), therhythm to determine if a shock is neeSHOCK button to deliver a shock.The device can be reconfigured to tuTo set options for AED mode, displayAED mode options include energy prtime, and others. For a complete desDefining Setup Options section in theNote: If configured to turn on in AE
turns off AED mode and placedoor does not restart AED moANALYZE or cycle the device
P Back Index Next Page
LIF Modes of Operation
S
In are configured in the SETUP menu. Options e operating characteristics, alarm setup,
is also a factory-reset option that resets the except the maintenance interval, which is complete, turn off the device to save the ce is turned on, the operating defaults last
ptions, refer to the Defining Setup Options
(Continued on next page)
4-5
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
etup Mode
troduction The operating defaults for the device include manual mode and AED modtime-of-day clock, and others. There device to the factory default settings,remains unchanged. After the setup configuration. The next time the deviselected will be active.For a complete description of setup osection in the operating instructions.
P Back Index Next Page
LIF Modes of Operation
S
DiM EVENT buttons, and then press the ON
DE overlay appears, release the buttons. indicating that the SPEED DIAL is active. SPEED DIAL to select a number and then er is selected, it changes to an asterisk for t digit in line highlights.de (0000) or the reserved technician
sed in place of other passcodes to gain E menus.code, press the SPEED DIAL. The SETUP CORRECT-TRY AGAIN message appears if
.ice OFF.
(Continued on next page)
4-6
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
etup Mode (continued)
splaying the Setup enu
To display the SETUP menu:1. Press and hold the OPTIONS and
button. When the ENTER PASSCOThe SPEED DIAL LED illuminates,
2. To enter the passcode, rotate thepress the SPEED DIAL. As a numbpasscode protection, and the nexNote: The factory default passcopasscode (5433 or LIFE) can be uaccess to the SETUP and SERVIC
3. When you have entered the passmenu appears. The PASSCODE INan incorrect passcode is entered
To exit the SETUP menu, turn the dev
P Back Index Next Page
LIF Modes of Operation
S
Se menu options.ptions section in the operating instructions ll options.
evice options
ode defaults
e defaults
faults
g defaults
ppear on the event overlay
faults
faults
time defaults
s to factory configuration settings
(Continued on next page)
4-7
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
etup Mode (continued)
tup Menu Options The following table defines the SETUP
Note: Refer to the Defining Setup Ofor complete descriptions of a
Option Description
GENERAL Set up general dMANUAL MODE Set up manual mAED MODE Set up AED modPACING Set up pacing deMONITORING Set up monitorinEVENTS Set up items to aALARMS Set up alarms dePRINTER Set up printer deCLOCK Set up date and RESET DEFAULTS Reset all default
P Back Index Next Page
LIF Modes of Operation
S
Se(c
SaCo
guration that cannot be disturbed, there p during repair procedures. System account, then use the LIFENET e setup configurations.sfer cable can be used to transfer the vice. After service is complete, transfer al device.
urrent configuration settings.
iguration to another device.
setup mode and archives mode.
CE menu.
(Continued on next page)
4-8
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
etup Mode (continued)
tup Menu Options ontinued)
ving the Setup nfiguration
If the device owner uses a setup confiare choices available to preserve setu■ If the device owner has a LIFENET
Device Agent application to manag■ The LIFEPAK 20 configuration tran
setup configuration to another dethe configuration back to the origin
Option Description
PRINT DEFAULTS Print a report of cSEND CONFIG Send device confSET PASSCODE Set passcodes forSERVICE Display the SERVI
P Back Index Next Page
LIF Modes of Operation
S
SaCo(c
nfiguration is to use SETUP menu to print service is complete, you can verify the e configuration. ansferring it to another device requires that software version. Otherwise, unexpected nfiguration is restored to the repaired
Cr SCODES in the SETUP menu. the SET PASSCODES submenu. .
enter setup mode.e access protocol for archives mode:(default) 3. Delete Only
4. Archive/Deleteenter archives mode.delete records in archives mode.
(Continued on next page)
4-9
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
etup Mode (continued)
ving the Setup nfiguration
ontinued)
■ Another way to save the setup cothe setup configuration. When setup and then manually reset th
Note: Saving the configuration by trboth devices have the same results can occur when the codevice.
eating a Passcode To create a passcode, select SET PAS
Select one of the following options in
Option DescriptionSETUP MODE Set passcode to ARCHIVES ACCESS Select a passcod
1. No Passcode 2. Archives Only
ARCHIVES MODE Set passcode to DELETE RECORDS Set passcode to
P Back Index Next Page
LIF Modes of Operation
S
Cr ce to any of the following protocols (refer to
ives mode and allow records to be deleted.rchives mode, but allow records to be
ves mode, but require a password to delete
rchives mode and delete records setup e to access the SETUP menu. The ENTER
ith the first digit highlighted. Rotate the
code to enter archives mode. The ENTER the first digit highlighted. Rotate the SPEED
scode to delete records in archives mode. pears with the first digit highlighted. Rotate
4-10
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
etup Mode (continued)
eating a Passcode ■ ARCHIVES ACCESS – Set the devithe table above):1. Allow unlimited access to arch2. Require a password to enter a
deleted.3. Allow unlimited access to archi
records.4. Require a password to enter a
MODE – Create a new passcodPASSCODE overlay appears wSPEED DIAL to select digits.
■ ARCHIVES MODE – Create a passPASSCODE overlay appears with DIAL to select digits.
■ DELETE RECORDS – Create a pasThe ENTER PASSCODE overlay apthe SPEED DIAL to select digits.
P Back Index Next Page
LIF Modes of Operation
S
In ualified service technicians to:
ure must be performed from start to finish
on
rillation rationad Test Test
■ Printer Test■ Audio Test
e Log Statusce Log Statuse Data
■ Counters Status■ Clear Memory
valterval
(Continued on next page)
4-11
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Mode
troduction The service mode functions enable q
* The performance inspection procedin the order presented.
Function Descripti
*Perform device calibration routines
■ DefibCalib
*Perform device tests ■ Keyp■ Pixels
View the device status registers
■ Devic■ Servi■ Devic
Set the service mode passcodeSet the maintenance prompt interReset the maintenance prompt in
P Back Index Next Page
LIF Modes of Operation
S
DiM
enu. (0000 or 5433). ss the SPEED DIAL. The SERVICE menu e is entered, the PASSCODE INCORRECT -
Se
evice OFF.
tor calibration procedure.
nce inspection procedure.
tatus.
ode access passcode.
erform preventative maintenance.
ETUP menu.
(Continued on next page)
4-12
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Mode (continued)
splaying the Service enu
To display the SERVICE menu:1. Display the SETUP menu.2. Select SERVICE from the SETUP m3. Enter the service mode passcode4. After you enter the passcode, pre
appears. (If an incorrect passcodTRY AGAIN message appears.)
rvice Menu Options The SERVICE menu options include:
To exit the SERVICE menu, turn the d
Option Description
Defib Cal Perform defibrilla
Tests Follow performa
Status Display device s
Set Passcode Set the service m
Maint Prompt Prompt user to p
Setup Return to main S
P Back Index Next Page
LIF Modes of Operation
S
SeM VICE menu. The SERVICE/SET PASSCODE
SPEED DIAL to select a number and then
SERVICE menu appears.
(Continued on next page)
4-13
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Mode (continued)
tting the Service ode Passcode
To set a service mode passcode:1. Select SET PASSCODE in the SER
overlay appears.2. Enter a passcode by rotating the
pressing the SPEED DIAL. 3. When the last digit is entered, the
P Back Index Next Page
LIF Modes of Operation
S
SePr
can be set to display a screen message ance prompt interval date has passed. The appears on the screen for the first d on. The device maintenance interval can
onths, or 12 months; the factory default is ice technician. e interval:
ICE/MAINT PROMPT submenu appears for scheduled maintenance (if set).ices are: OFF, 3 MONTHS, 6 MONTHS, and
(Continued on next page)
4-14
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Mode (continued)
tting a Maintenance ompt Interval
The LIFEPAK 20 defibrillator/monitorthat alerts the user when the maintenscreen message MAINTENANCE DUE 10 minutes after the device is powerebe turned off or set to 3 months, 6 mOFF, but it can be activated by a servTo change the scheduled maintenanc1. Display the SERVICE menu.2. Select MAINT PROMPT. The SERV
showing the current prompt date 3. Select INTERVAL. The interval cho
12 MONTHS.4. Select the desired interval.5. Turn the device OFF.
P Back Index Next Page
LIF Modes of Operation
S
ReM
nce, reset the maintenance prompt counter age and begin the count for the next
intenance prompt:
CE/MAINT PROMPT menu appears, showing uled maintenance.
revised to the next scheduled maintenance
4-15
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Mode (continued)
setting the aintenance Prompt
After completing scheduled maintenato clear the MAINTENANCE DUE messscheduled maintenance.To turn off or reset the scheduled ma1. Display the SERVICE menu.2. Select MAINT PROMPT. The SERVI
the current prompt date for sched3. Select RESET. The prompt date is
date.4. Turn the device OFF.
P Back Index Next Page
LIF Modes of Operation
In
In ctice or demonstrate the monitoring include:e, and volume, and moving ECG waveform
able in the Inservice mode.
EnM e. Inservice mode cannot be entered if
.d EVENT buttons, turn the device ON. INSERVICE overlay appears.e OFF.
4-16
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
service Mode
troduction Inservice mode enables users to prafunctions of the device. The functions■ Selecting ECG lead selection, siz
with heart rate■ SpO2 ■ Alarms■ EventsNote: No therapy features are avail
tering Inservice ode
To enter Inservice mode:1. Remove all cables from the devic
cables are attached to the device2. While holding down the HOME an
Release these buttons when the To exit Inservice mode, turn the devic
Previous Page Table of Contents Back Index Next Page
LIFEPAK 20/20e Defibrillator/Monitor Section Contents
Performance Inspection Procedures
The Performance Inspection Procedures (PIP), document reference number 3201896, are a set of manual test procedures used for an operational closed-case evaluation of the LIFEPAK 20/20e defibrillator/monitor (device).The PIP describes the test procedures you will perform to determine if the device is operating within the required specifications. Investigate and correct any malfunctions or out-of-tolerance conditions detected during the PIP.The PIP is comprised of safety and performance tests recommended by AHA/ASHE (American Hospital Association/American Society for Hospital Engineering) Maintenance Management for Medical Equipment and International Electrotechnical Commission (IEC) Technical Report 1288-2, Maintenance of Cardiac Defibrillators-Monitors. Perform the PIP as part of a regularly scheduled preventive maintenance routine. Perform the PIP after any repair, replacement, or calibration procedure. Use the PIP Checklist to record test results. Refer to the Operator Checklist for additional items.
LIF Section Contents
P Back Index Next Page
Tr code usage, interpretation, and corrective leshooting chart for the performance
idual troubleshooting tests that require the following topics:
rd Replacement
EPAK 20/20e Defibrillator/Monitor
revious Page Table of Contents
8oubleshooting This section describes service event action, and provides a separate troubinspection procedure (PIP) and indivoperator interpretation. Choose from
Processing Service CodesTroubleshooting ChartService Code Categories Service Code TableService IndicatorDevice User TestDevice Printed Circuit Boa
P Back Index Next Page
LIF Troubleshooting
P
In fails to execute properly, a service code is turns ON. Service codes rarely occur and ualified service personnel before the
Always complete the performance ntering and clearing any service code(s).
og may not necessarily indicate a dicate transient electromagnetic charge (ESD). If you suspect transient
clear the service code(s), and cycle the occur, it may have been the result of EMI
PrCo and consult the Troubleshooting Chart.
ce Log. Record the service code(s), ce code extension.g, and then turn the device OFF.
(Continued on next page)
6-2
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
rocessing Service Codes
troduction When an internal program or process logged and the service indicator LED should be investigated thoroughly by qdevice is placed back into active use. inspection procedure (PIP) after encouService codes stored in the Service Lpermanent error. Service codes can ininterference (EMI) or electrostatic disEMI or ESD as the source of an error,power. If the service code does not reor ESD.
ocessing Service des
To process service code(s):1. Note any problems with the device2. Review service codes in the Servi
including the date, time, and servi3. Select CLEAR LOG in the service lo
P Back Index Next Page
LIF Troubleshooting
P
PrCo
tion procedure (PIP). device may be returned to regular use. e been related to EMI or ESD.) any time during the PIP, stop the PIP and s procedure.rt for the suggested corrective action for
nd then locate the service code in the
Code Categories table to quickly jump to de Table.e corrective action calls for the k in the Troubleshooting Chart or click the bottom of the Service Code Table pages cess. inputs, and then repeat the PIP. your local Physio-Control service or sales
6-3
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
rocessing Service Codes (continued)
ocessing Service des (continued)
4. Complete the performance inspec– If completed successfully, the
(The service code(s) may hav– If the service LED turns ON at
continue to the next step in thi5. Consult the Troubleshooting Cha
your PIP failure. -OR-Review the Service Log codes, aService Code Table.Note: Use the links in the Servicethe correct code in the Service Co
6. Read the corrective action(s). If threplacement of a part, click the linappropriate part in the footer at theto jump to the corrective action pro
7. Service the device based on these8. For persistent error codes, contact
representative.
P Back Index Next Page
LIF Troubleshooting
TrA rective Action
Ph en or replace loose items.ce broken components.
l cleaning.
mer keypad.t identification label.on/hazard label.ng instruction label.
Po to ac power source.s Alert alarm.
(Continued on next page)
6-4
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oubleshooting Chart rea Observed Symptom Suggested Cor
ysical Inspection Loose or broken hardware Locate and tightLocate and repla
Evidence of dirt, fluids, or foreign objects
Perform externa
Damaged keypad or labels Replace elastoReplace producReplace explosiReplace operati
wer Off Device beeps when turned off
Connect device Disable AC Los
P Back Index Next Page
LIF Troubleshooting
TrA orrective Action
Po ace the W18 UI Flex Cable.ace the A05 UI PCB.A04 Therapy PCB.
A01 System PCB.
ace the W18 UI Flex Cable.A01 System PCB.
A05 UI PCB.
essing Service Codes for assistance.
tenance Prompt interval.intenance Prompt interval.
Ke ad test.ace the elastomer keypad.A05 UI PCB.
ad test.ace standard paddles.ace the W01 Therapy Connector.A04 Therapy PCB.
(Continued on next page)
6-5
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oubleshooting Chart (continued) rea Observed Symptom Suggested C
wer On Display on, no power-on LED Check or replCheck or replReplace the
Continuous reset Replace the Frozen at the power-on screen Check or repl
Replace the Distorted display Replace the Service indicator remains on Refer to ProcMAINTENANCE DUE message remains on screen
Set the MainReset the Ma
ypad Improper button response Perform keypCheck or replReplace the
Standard paddle buttons Perform keypCheck or replCheck or replReplace the
P Back Index Next Page
LI Troubleshooting
TA rrective Action
P test.r paper. on pins 14 and 16 on the J38 test he A05 UI PCB.igher than 3.3 V, replace the W14 Printer .ower than 3.3 V: r replace the A12 Printer Assembly. the A05 UI PCB.
per paper. Printer Flex Cable connection.e the A05 UI PCB.
per paper.ead.e the A12 Printer Assembly.
(Continued on next page)
6-6
revious Page Table of Contents Section Contents
FEPAK 20/20e Defibrillator/Monitor
roubleshooting Chart (continued) rea Observed Symptom Suggested Co
rinter Not printing Perform printer Check for propeCheck for 3.3 Vconnector on t■ If either is h
Flex Cable■ If both are l
– Check o– Replace
Light print Verify use of proCheck the W14Check or replac
Missing or broken characters Verify use of proClean the printhCheck or replac
P Back Index Next Page
LIF Troubleshooting
TrA rrective Action
Au ce tone test.ker connection.e the W02 Speaker Assembly.e the A01 System PCB.
Pom
7 Battery.e the A03 Power Module.
Then
ith proper test load shorting.y of the test plug or shorting bar.y of the QUIK-COMBO cable.e the W01 Therapy Connector.4 Therapy PCB.
lator calibration.
Pach
e the A14 Inductive Resistor (less than
e the A04 Therapy PCB.1 System PCB.
(Continued on next page)
6-7
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oubleshooting Chart (continued) rea Observed Symptom Suggested Co
dio Inaudible or garbled audio Perform the voiCheck the speaCheck or replacCheck or replac
wer source anagement
No backup battery operation Replace the A0Check or replac
erapy - delivered ergy
Unable to complete auto test or user test
Rerun the test wCheck continuitCheck continuitCheck or replacReplace the A0
Delivered energy out of tolerance
Perform defibril
tient impedance annel broken
Abnormal energy delivery Check or replac5 ohms).Check or replacReplace the A0
P Back Index Next Page
LIF Troubleshooting
TrA rective Action
Pach(c
0 ohm load during 3:00 AM test, rerun test plug.omplete PIP.ace the A01 System PCB.
of the QUIK-COMBO cable; replace if
of the W01 Therapy Connector; sary.1 System PCB.
Thca
e the Therapy cable.e the W01 Therapy Connector.1 System PCB.
ECG signal.e the ECG cable.e the W06 ECG connector.e the A02 Patient Parameter PCB.1 System PCB.
(Continued on next page)
6-8
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oubleshooting Chart (continued) rea Observed Symptom Suggested Cor
tient impedance annel broken ontinued)
Low patient impedance If tested into a 5test with correctIf test passes, cIf test fails, repl
Therapy cable leads off (QUIK-COMBO only)
Check continuitynecessary.Check continuityreplace if necesReplace the A0
erapy - Synchronous rdioversion
No paddles channel sync mark
Check or replacCheck or replacReplace the A0
No lead channel sync mark Check for noisyCheck or replacCheck or replacCheck or replacReplace the A0
P Back Index Next Page
LIF Troubleshooting
TrA rective Action
Thca
ker placement on R-wave.pad test.eplace the A05 UI PCB.s, run the user test and troubleshoot error
Pach
urer configuration bit setting. test:heck key tactile feedback. the elastomer keypad. the A05 UI PCB.s, follow error code procedure.
e the A04 Therapy PCB.
EC e the ECG cable.e the W06 ECG Connector.2 Patient Parameter PCB.
(Continued on next page)
6-9
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oubleshooting Chart (continued) rea Observed Symptom Suggested Cor
erapy - Synchronous rdioversion (continued)
Failure to transfer coincident with sync mark
Check sync marPerform the key■ If test fails, r■ If test passe
code.
cer option aracteristics
Pacer does not turn on Verify manufactPerform keypad■ If test fails, c
– Replace– Replace
■ If test passe
Pacing current/rate out of tolerance
Check or replac
G lead characteristics No ECG Check or replacCheck or replacReplace the A0
P Back Index Next Page
LIF Troubleshooting
TrA rrective Action
EC(c
e the ECG cable.2 Patient Parameter PCB.
r output.e the ECG cable.e the A02 Patient Parameter PCB.
Thle
r output.e the therapy cable.e the A01 System PCB.
r output.display.G out connector.
Re sync function.t/Sync In connector. If bad, replace the dule.e the W09 Power Cable.e the A01 System PCB.e the A03 Power module.
(Continued on next page)
6-10
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oubleshooting Chart (continued)
rea Observed Symptom Suggested Co
G lead characteristics ontinued)
No amplitude ECG Check or replacReplace the A0
ECG gain out of tolerance Check simulatoCheck or replacCheck or replac
erapy - Paddle ECG ad characteristics
ECG gain out of tolerance Check simulatoCheck or replacCheck or replac
ECG analog out (missing or out of tolerance)
Check simulatoCheck ECG on Check W11 EC
mote sync No remote sync Turn on remoteCheck ECG OuA03 Power moCheck or replacCheck or replacCheck or replac
P Back Index Next Page
LIF Troubleshooting
TrA rective Action
O e the SpO2 cable.e the SpO2 sensor.e the W05 SpO2 Assembly.
e the SpO2 cable.e the SpO2 sensor.e the W05 SpO2 Assembly.e the A06 OEM PCB.
Sp e the W04 Speed Dial Assembly.5 UI PCB.
Nto
figuration setting.3 Power module.
G e the power cord.3 Power module.
Le 3 Power module.
6-11
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oubleshooting Chart (continued) rea Observed Symptom Suggested Cor
ximeter No SpO2 response (no cable detected)
Check or replacCheck or replacCheck or replac
Saturation reading missing or out of tolerance
Check or replacCheck or replacCheck or replacCheck or replac
eed Dial Speed Dial not functioning Check or replacReplace the A0
o ac power reminder ne
No alert Check user conReplace the A0
rounding resistance Fails ground resistance test Check or replacReplace the A0
akage current Fails chassis leakage test Replace the A0
P Back Index Next Page
LIF Troubleshooting
S
Co l format:
In d Assemblies
0x1x erapy, A05 UI, A12 Printer,
ble, W18 UI Flex Cable 2x3x4x erapy, A05 UI,
50 PCB, A04 Therapy, A05 UI,
51 A04 Therapy, A07 Battery,
6x EM PCB, A10 SpO2 Module 8x PCB 9x wer Module, A04 Therapy, A07 Batteryaxbx
6-12
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Categories
des are organized into the following categories, in four-digit hexadecima
itial Digit Category Description Associated PCBs an
xx UT Utilities A01 System xx UI User Interface A01 System, A04 Th
W14 Printer Flex Caxx DC Data Communications A01 System xx DM Data Management A01 System xx SM System Monitor A01 System, A04 Th
W18 UI Flex Cable xx PC Processor Control A01 System, A02 PP
W18 UI Flex Cable xx PM Power Management A03 Power Module,
W08 Battery Cable xx PP Patient Parameter – SpO2 A02 PP PCB, A06 Oxx DSP Digital Signal Processor A01 System, A02 PPxx TH Therapy A01 System, A03 Poxx PR Printer A12 Printer xx BM Behavior Manager A01 System
P Back Index Next Page
LIF Troubleshooting
SC ive Action
00 the A01 System PCB00 the A01 System PCB00 the A01 System PCB00 the A01 System PCB00 the A01 System PCB00 the A01 System PCB00 the A01 System PCB00 the A01 System PCB00 the A01 System PCB00 the A01 System PCB10 lace the W18 UI Flex Cable
lace the A05 UI PCBlace the A01 System PCB
10 ad the device software*lace the A01 System PCB
orced update mode (Continued on next page)
W18 UI Flex Cable
6-13
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table
ode Service Code Description Correct
02 System Flash memory voltage error Replace03 Cannot erase system Flash memory Replace04 Cannot write to system Flash memory Replace06 System ADC read error Replace07 System DAC not responding Replace08 ECG OUT DAC self-test failed Replace0a System ADC background test failed Replace0b System ADC failed self-calibration Replace0c System Flash memory ID unknown Replace0d System hardware/software configuration lost Replace0e UI – system communication lost 1. Rep
2. Rep3. Rep
0f Display update timer error 1. Relo2. Rep
* Use software loader tool in f
A01 System PCB A05 UI PCB
P Back Index Next Page
LIF Troubleshooting
SC ive Action Code10 ad the device software*
lace the A01 System PCB10 lace the W18 UI Flex Cable
lace the A05 UI PCB10 ad the device software*
lace the A01 System PCB10 r error and perform PIP
lace the W18 UI Flex Cable1c the A05 UI PCB1c the A05 UI PCB1c ad the device software*
lace the A05 UI PCB1c the A05 UI PCB
(Continued on next page)
W18 UI Flex Cable
6-14
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
ode Service Code Description Correct10 Display update queue error 1. Relo
2. Rep13 System detected unexpected UI reset 1. Rep
2. Rep14 Voice prompt/audio watchdog failure 1. Relo
2. Rep15 USB data time-out error 1. Clea
2. Rep01 UI FPGA programming error Replace02 UI FPGA verification error Replace03 UI FPGA program file error 1. Relo
2. Rep04 UI ADC not functioning Replace
A01 System PCB A05 UI PCB
P Back Index Next Page
LIF Troubleshooting
SC tive Action1c ck the W14 Printer Flex Cable
lace the A12 Printerlace the A05 UI PCB
1c ck the W14 Printer Flex Cablelace the A12 Printerlace the A05 UI PCB
1c the A05 UI PCB1c the A05 UI PCB1c the A05 UI PCB1c the A05 UI PCB1c the A05 UI PCB1c the A05 UI PCB1c the A05 UI PCB1c the A05 UI PCB
(Continued on next page)
A05 UI PCB
6-15
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
ode Service Code Description Correc05 Printer ADC out of tolerance (temperature) 1. Che
2. Rep3. Rep
06 Printer ADC out of tolerance (voltage) 1. Che2. Rep3. Rep
07 UI voltage out of tolerance (5 V) Replace08 UI voltage out of tolerance (3.3 V) Replace09 UI voltage out of tolerance (2.5 V) Replace0a UI voltage out of tolerance (35 V) Replace0b UI voltage out of tolerance (SW VBATT) Replace0c UI voltage out of tolerance (ground) Replace0f UI hardware I.D. corrupted Replace10 UI boot program corrupted Replace
W14 Printer Flex Cable A12 Printer
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
A05 UI PCB
C ive Action1c ad the device software*
lace the A05 UI PCB1c ad the device software*
lace the A05 UI PCB1c ad the device software*
lace the A05 UI PCB1c the A05 UI PCB1c the A05 UI PCB1f n required; refer to error code logged
fff.20 the A01 System PCB20 ad the device software*
lace the A01 System PCB
6-16
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A01 System PCB
ode Service Code Description Correct11 UI application Flash memory corrupted 1. Relo
2. Rep12 UI font Flash memory corrupted 1. Relo
2. Rep13 UI FPGA Flash memory corrupted 1. Relo
2. Rep16 UI CPU RAM test failed on power-on Replace17 UI CPU RAM test failed during normal operation Replaceff Additional information related to error code that is
logged before 1fffNo actiobefore 1
04 System cannot initialize serial port (system connector) Replace05 System cannot initialize driver for serial port (system
connector)1. Relo2. Rep
P Back Index Next Page
LIF Troubleshooting
SC tive Action30 oad the device software*
lace the A01 System PCB30 ar memory (service mode)
oad the device software*lace the A01 System PCB
30 ar memory (service mode)oad the device software*lace the A01 System PCB
30 ar memory (service mode)oad the device software*lace the A01 System PCB
30 ar memory (service mode)oad the device software*lace the A01 System PCB
(Continued on next page)
6-17
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
ode Service Code Description Correc01 System cannot use data management (DM) Flash
memory1. Rel2. Rep
02 System data management Flash memory corrupted 1. Cle2. Rel3. Rep
05 System cannot delete DM record 1. Cle2. Rel3. Rep
07 System cannot create new DM record 1. Cle2. Rel3. Rep
08 System could not store DM record 1. Cle2. Rel3. Rep
A01 System PCB
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
C tive Action30 ar memory (service mode)
oad the device software*lace the A01 System PCB
30 oad the device software*lace the A01 System PCB
30 ar memory (service mode)oad the device software*lace the A01 System PCB
30 ar memory (service mode)oad the device software*lace the A01 System PCB
30 the A01 System PCB3f n required; refer to error code logged
fff.
6-18
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A01 System PCB
ode Service Code Description Correc09 System could not erase oldest DM record 1. Cle
2. Rel3. Rep
0a System cannot clear DM memory 1. Rel2. Rep
0b System error writing DM record 1. Cle2. Rel3. Rep
0c System cannot read archived DM record 1. Cle2. Rel3. Rep
10 System error DM memory corrupt Replaceff Additional information related to error code that is
logged before 3fffNo actiobefore 3
P Back Index Next Page
LIF Troubleshooting
SC ive Action40 lace the coin cell battery
ad the device software*lace the A01 System PCB
40 ad the device software*lace the A01 System PCB
40 ad the device software*lace the A01 System PCB
40 ad the device software*lace the A01 System PCB
40 ad the device software*lace the A01 System PCB
40 ck coin-cell batteryror still occur, Replace A01 System PCB
40 the A01 System PCB40 the A01 System PCB
(Continued on next page)
Coin Battery
6-19
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
ode Service Code Description Correct05 System NVRAM error log 1. Rep
2. Relo3. Rep
06 Error log queue not functioning 1. Relo2. Rep
08 Error log count corrupted 1. Relo2. Rep
09 System RAM test failed 1. Relo2. Rep
0a System program Flash memory corrupted 1. Relo2. Rep
0b Program contents failure 1. Che2. If er
0c System ADC voltage low Replace0d System ADC voltage high Replace
A01 System PCB
P Back Index Next Page
LIF Troubleshooting
SC ive Action40 lace the W18 UI Flex Cable
lace the A05 UI PCBlace the A04 Therapy PCB
40 the device software*40 the device software*4f n required for 4fff; refer to error code
before 4fff.50 the A01 System PCB50 ad the device software*
lace the A01 System PCB50 the A01 System PCB50 the A01 System PCB50 ad the device software*
lace the A01 System PCB50 the A01 System PCB
(Continued on next page)
A CB W18 UI Flex Cable
6-20
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
ode Service Code Description Correct10 Service LED failed 1. Rep
2. Rep3. Rep
12 Voice Flash memory corrupted Reload 13 Voice/font Flash memory invalid Reload
ff Additional information related to error code that is logged before 4fff
No actiologged
03 System watchdog failed Replace04 System watchdog reset 1. Relo
2. Rep05 System CPU error during boot-up Replace06 System RAM failed during boot-up Replace07 System checksum failure during boot-up 1. Relo
2. Rep08 System boot program failure Replace
01 System PCB A04 Therapy PCB A05 UI P
P Back Index Next Page
LIF Troubleshooting
SC ive Action50 ad the device software*
lace the A01 System PCB50 lace the coin cell battery
lace the A01 System PCB50 ad the device software*
lace the A01 System PCB50 ad the device software*
lace the A01 System PCB50 ad the device software*
lace the A01 System PCB50 ad the device software*
lace the A01 System PCB50 the coin cell battery
(Continued on next page)
Coin Battery
6-21
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
ode Service Code Description Correct09 Real-time clock (RTC) access failed 1. Relo
2. Rep0a Coin cell battery not detected 1. Rep
2. Rep0b Cannot use system NVRAM 1. Relo
2. Rep0c System application start error 1. Relo
2. Rep0d System software initialization time out 1. Relo
2. Rep0e System application start error 1. Relo
2. Rep10 Configuration mismatch Replace
A01 System PCB
P Back Index Next Page
LIF Troubleshooting
SC ive Action50 lace the coin cell battery
ad the device software*50 the coin cell battery50 the device software*50 the coin cell battery50 the A01 System PCB50 the A01 System PCB50 the A01 System PCB50 the A01 System PCB50 the coin cell battery50 the coin cell battery50 lace the coin cell battery
lace the A01 System PCB
(Continued on next page)
Coin Battery
6-22
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
ode Service Code Description Correct11 NVRAM configuration data error 1. Rep
2. Relo12 Configuration data error Replace13 System meter initialization error Reload 14 System meter mismatch Replace15 NVRAM error Replace16 MFG data mismatch Replace17 NVRAM MFG data lost Replace18 Watchdog reset failed Replace19 NVRAM corrupted Replace1a NVRAM corrupted Replace1c RTC not running 1. Rep
2. Rep
A01 System PCB
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
Coin Battery
C n50 oin cell battery
01 System PCB50 software*50 software*50 software*50 software*50 software*50 software*50 software*50 cell battery50 d perform PIP
01 System PCB50 d perform PIP
02 PP PCB
6-23
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A01 System PCB A02 PP PCB
ode Service Code Description Corrective Actio1d RTC out of sync 1. Replace the c
2. Replace the A1e System software execution error Reload the device1f System software read error Reload the device20 System software write error Reload the device21 System software error Reload the device22 System software exception code Reload the device23 System software exception code Reload the device24 System software exception code Reload the device26 NVRAM low battery interrupt Replace the coin 27 System USB did not initialize 1. Clear error an
2. Replace the A28 PP USB did not initialize 1. Clear error an
2. Replace the A
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
A A02 PP PCB W18 UI Flex Cable
C ive Action50 r error and perform PIP
lace the A04 Therapy PCB50 r error and perform PIP
lace the W18 UI Flex Cablelace the A05 UI PCB
50 r error and perform PIPlace the A01 System PCB
50 ck configuration codedevice type (software loader program)lace the A01 System PCB
50 r error and perform PIPlace the A02 PP PCB
50 r error and perform PIPlace the W18 UI Flex Cablelace the A05 UI PCB
6-24
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
04 Therapy PCB A01 System PCB A05 UI PCB
ode Service Code Description Correct29 Therapy USB did not initialize 1. Clea
2. Rep2a UI USB did not initialize 1. Clea
2. Rep3. Rep
2b USB system failed 1. Clea2. Rep
2f Device type invalid 1. Che2. Set 3. Rep
30 PP USB disconnect 1. Clea2. Rep
31 UI USB disconnect 1. Clea2. Rep3. Rep
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
y PCB A05 UI PCB
C e Action
50 error and perform PIPce the A04 Therapy PCB
50 error and perform PIPd the device software*
50 error and perform PIPd the device software*ce the A01 System PCB
50 error and perform PIPd the device software*ce the A01 System PCB
50 he A01 System PCB
50 error and perform PIPce the A02 PP PCBce the A01 System PCB
6-25
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A01 System PCB A02 PP PCB A04 Therap
ode Service Code Description Correctiv
32 Therapy USB disconnect 1. Clear 2. Repla
33 PP USB download time out 1. Clear 2. Reloa
36 USB initialization failed 1. Clear 2. Reloa3. Repla
37 USB unitization error 1. Clear 2. Reloa3. Repla
38 Cannot clear interrupt source Replace t
39 Bus error reported by USB PP channel 1. Clear 2. Repla3. Repla
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
A07 Battery
C ive Action
50 r error and perform PIPlace the A05 UI PCBlace the A01 System PCB
50 r error and perform PIPlace the A04 Therapy PCBlace the A01 System PCB
50 r error and perform PIPlace the A01 System PCB
50 r error and perform PIPlace the A01 System PCB
50 the A01 System PCB
6-26
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A01 System PCB A03 Power Module
ode Service Code Description Correct
3a Bus error reported by USB UI channel 1. Clea2. Rep3. Rep
3b Bus error reported by USB therapy channel 1. Clea2. Rep3. Rep
3c USB host driver cannot create transfer descriptor 1. Clea2. Rep
3d USB host driver received message larger than maximum allowed
1. Clea2. Rep
40 Inconsistent RTC time Replace
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
A07 Battery
C ive Action
51 lace the A07 Batterylace the A03 Power module
51 wer supply voltage is <14 Vdc, replace Power module4 Vdc, clear error and perform PIP
51 the A03 Power module
51 the A03 Power module
51 lace the A07 Batterylace the A03 Power module
51 the A03 Power module
51 the A03 Power module
51 the A03 Power module
51 the A07 Battery
6-27
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A03 Power Module A04 Therapy PCB
ode Service Code Description Correct
05 Battery failed to reach charge in 2.5 hours 1. Rep2. Rep
06 Power supply out of tolerance 1. If poA03
2. If >1
07 Power module RAM error Replace
08 Power module self-test service code Replace
0a Battery <10 V after 20 minutes of charging 1. Rep2. Rep
0b Does not switch to battery power Replace
0c Does not detect ac disconnect Replace
0d Battery powered when connected to ac power Replace
0e Battery <10 V after charge cycle Replace
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
A07 Battery
C ive Action
51 ck battery connectionlace the A07 Batterylace the A03 Power module
51 the A03 Power module
51 ck the A07 Battery connectionck W08 Battery Cableck for valid power hardware ID in VICE/STATUS/DEVICE DATA overlaylace the A07 Batterylid power hardware ID; replace the Power module power hardware ID; replace the Therapy PCB
6-28
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A03 Power Module
ode Service Code Description Correct
0f Battery charge cycle stopped 1. Che2. Rep3. Rep
10 AC isolation diode shorted Replace
12 Battery not detected 1. Che2. Che3. Che
SER4. Rep5. Inva
A036. Valid
A04
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
A02 PP PCB
C ive Action
51 A07 Battery (LIFEPAK 20e)asurement of white wires of A07 Battery thermistor LIFEPAK 20)lace the A07 Battery if <400 Ohmslace the A03 Power module if >400 Ohms
51 the A03 Power module
51 lace the A07 Batterylace the A03 Power module
51 the A07 Battery
51 the A07 Battery
5f n required for 5fff; refer to error code efore 5fff
6-29
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A06 OEM PCB
ode Service Code Description Correct
15 Battery thermistor <400 Ohms ReplaceOhm me(battery ■ Rep■ Rep
16 Charger reporting zero during battery charging Replace
17 No 12C connection detected (LIFEPAK 20e only)
1. Rep2. Rep
18 Power module connected to NiMH battery(LIFEPAK 20 only)
Replace
1a Battery failure Replace
ff Additional information related to error code that is logged before 5fff
No actiologged b
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
10 SpO2 Module
C ive Action
60 the device software*
60 the device software*
60 the device software*
60 the device software*
60 ck configurationad the device software*
60 ad the device software*lace the A02 PP PCB
60 ck configurationad the device software*
60 the device software*
60 the A06 OEM PCB
60 the A06 OEM PCB
6-30
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A02 PP PCB A
ode Service Code Description Correct
02 PP program corrupted Reload
03 PP program not found Reload
04 PP boot-up error Reload
09 No PP data Reload
0c SpO2 misconfigured 1. Che2. Relo
0e PP reset 1. Relo2. Rep
0f OEM configuration error 1. Che2. Relo
10 PP initialization error Reload
18 Incorrect updated SpO2 image Replace
19 Incorrect updated SpO2 image CRC Replace
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
C tive Action
68 e the A02 PP PCB
68 ar error and perform PIPlace the A02 PP PCB
68 ar error and perform PIPlace the A02 PP PCB
68 ar error and perform PIPlace the A02 PP PCB
68 ar error and perform PIPlace the A02 PP PCB
68 ar error and perform PIPlace the A02 PP PCB
68 e the A10 SpO2 Module
6f on required for 6fff; refer to error logged 6fff.
6-31
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A01 System PCB
ode Service Code Description Correc
01 PP power supply out of tolerance Replac
02 PP pre-amp data invalid 1. Cle2. Rep
04 PP data RAM test error 1. Cle2. Rep
05 PP RAM test error 1. Cle2. Rep
06 PP CRC test error 1. Cle2. Rep
07 PP ECG test error 1. Cle2. Rep
0b SpO2 board error Replac
ff Additional information related to error code that is logged before 6fff
No actibefore
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
A04 Therapy PCB
C tive Action
80 the device software*
80 the device software*
80 oad the device software*lace the A01 System PCB
80 ar error and perform PIPlace the A01 System PCB
81 the A01 System PCB
81 oad the device software*lace the A01 System PCB
81 un the user testlace the A01 System PCB
81 form TCP - defibrillator calibrationlace the A01 System PCB
6-32
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A01 System PCB A07 Battery
ode Service Code Description Correc
0a System DSP error Reload
13 Voice format error Reload
14 No paddles data 1. Rel2. Rep
1b DSP did not receive USB SOF (start of frame) interrupt 1. Cle2. Rep
05 Impedance channel out of calibration Replace
08 Paddles data out of sync 1. Rel2. Rep
09 Paddles pre-amp user test failed 1. Rer2. Rep
0b Real impedance <-30 ohms for one second 1. Per2. Rep
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
A04 Therapy PCB
C ive Action
8f n required for 8fff; refer to error logged fff.
90 the A01 System PCB
90 the A01 System PCB
90 the device software*
90 the A07 Battery
90 the A01 System PCB
90 ck the stack connectorlace the A04 Therapy PCB
90 ad the device software*lace the A04 Therapy PCB
90 the device software*
90 the device software*
6-33
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A01 System PCB
ode Service Code Description Correct
ff Additional information related to error code that is logged before 8fff
No actiobefore 8
04 Unable to initialize therapy control Replace
05 Defib disabled Replace
07 Shock not delivered Reload
09 Defib charge time expired Replace
0b Pacing rate out of tolerance Replace
0f Unable to initialize therapy control 1. Che2. Rep
11 Pacer fault 1. Relo2. Rep
17 Pacer disabled Reload
1a Pacer rate storage corrupted Reload
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
Therapy PCB
C ive Action
90 ck the stack connectorlace the A04 Therapy PCB
90 the A01 System PCB
90 r error and perform PIPlace the A01 System PCB
9c the A04 Therapy PCB
9c the A01 System PCB
9c r error and perform PIPlace the A04 Therapy PCB
9c orm TCP - defibrillator calibrationr Service Log
9c orm TCP - defibrillator calibrationr Service Log
6-34
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A03 Power Module A04
ode Service Code Description Correct
1b Therapy PCB communication lost 1. Che2. Rep
1d Testing purpose only Replace
21 Impedance value indicates regulator in System PCB pre-amp failed
1. Clea2. Rep
03 Therapy processor, unplanned reset Replace
04 Therapy/system controller communication watchdog Replace
05 CRC error 1. Clea2. Rep
06 Calibration constant A out of range 1. Perf2. Clea
07 Calibration constant B out of range 1. Perf2. Clea
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
Therapy PCB
C ive Action
9c ad the device software*lace the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c ck power module 26-pin ribbon cable to or A04 Therapy PCBlace the A03 Power modulelace the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
6-35
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A01 System PCB A04
ode Service Code Description Correct
08 Therapy ROM cyclic redundancy check (CRC) failed 1. Relo2. Rep
09 Therapy RAM pattern write test failed Replace
0a Therapy relay idle coil voltage out of range Replace
0b Therapy relay enabled coil voltage out of range (5 ms) Replace
0c Therapy relay enabled coil voltage out of range (100 ms)
Replace
0d Therapy relay drive enabled coil voltage out of range Replace
0f Therapy/power assembly communication error 1. CheJ16
2. Rep3. Rep
11 Capacitor Dump failed Replace
12 Therapy PCB 5 V out of range Replace
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
C ive Action
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c orm TCP - defibrillator calibrationr Service Log
6-36
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A04 Therapy PCB
ode Service Code Description Correct
13 Therapy PCB 15 V out of range Replace
14 Therapy PCB -15 V out of range Replace
15 Therapy ADC time out error Replace
18 3:00 AM H bridge test: NE leg shorted Replace
19 3:00 AM H bridge test: SE leg shorted Replace
1a 3:00 AM H bridge test: NW leg shorted Replace
1b 3:00 AM H bridge test: SW leg shorted Replace
1c 3:00 AM H bridge test: east side stuck open Replace
1d 3:00 AM H bridge test: west side stuck open Replace
1e 3:00 AM H bridge test: charge time out of range 1. Perf2. Clea
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
C ive Action
9c ctive resister is not connected or is openlace the A04 Therapy PCBlace the A01 System PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
6-37
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A04 Therapy PCB
ode Service Code Description Correct
1f 3:00 AM shorted paddles relay contact test: relay shorted
1. Indu2. Rep3. Rep
20 3:00 AM shorted paddles relay contact test: relay shorted
Replace
21 3:00 AM pace drive test: pace power supply stuck on Replace
22 3:00 AM pace drive test: pace power supply inoperable Replace
23 3:00 AM pace drive test: relay contacts shorted Replace
24 3:00 AM pace drive test: relay drive low side shorted Replace
25 3:00 AM pace drive test: relay drive high side shorted Replace
26 3:00 AM pace drive test: pace FET shorted Replace
27 3:00 AM pace drive test: pace current path open Replace
28 3:00 AM pace drive test: pace set point error Replace
P Back Index Next Page
LIF Troubleshooting
S
(Continued on next page)
C ive Action
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c rgy capacitor is not connected or is openlace the A04 Therapy PCB
9c the A04 Therapy PCB
6-38
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A04 Therapy PCB
ode Service Code Description Correct
29 3:00 AM redundant controls test: redundant controls stuck on
Replace
2a 3:00 AM redundant controls test: enable 2 stuck on Replace
2b 3:00 AM redundant controls test: enable 1 stuck on Replace
2c Capacitor voltage per pacing pulse too high Replace
2d Capacitor current per pacing pulse too high Replace
2e Cap current per pacing pulse too high Replace
2f Pacing current and selected current out of range Replace
30 Pacing pulse width too short Replace
31 Pacing pulse width too long Replace
32 Capacitor voltage and predicted capacitor voltage mismatch
1. Ene2. Rep
35 Therapy CPU instruction test failed Replace
P Back Index Next Page
LIF Troubleshooting
S
C ive Action
9c the device software*
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
9c the A04 Therapy PCB
6-39
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued)
A04 Therapy PCB
ode Service Code Description Correct
36 Therapy software stack overflow Reload
3a Energy capacitor overvoltage error Replace
3b 3:00 AM redundant controls test: charge rate stuck on Replace
3e Therapy software error Replace
3f Therapy software error Replace
P Back Index Next Page
LIF Troubleshooting
SC ive Action
a0 r error and perform PIPad the device software*
a0 he device software*
b0 r error and perform PIPlace A01 System PCB
b0 he device software*
b0 he device software*
b0 he device software*
b0 he device software*
b0 he device software*
b0 he device software*
b0 r error and perform PIP. lace A01 System PCB.
(Continued on next page)
6-40
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Code Table (continued) ode Service Code Description Correct
0b Printer communication lost 1. Clea2. Relo
0e Printer initialization error Reload t
01 Invalid state request 1. Clea2. Rep
11 System behavior manager error Reload t
12 Energy cap charging time out Reload t
13 Shock advisory system error Reload t
14 Shock advisory system time out Reload t
16 Motion detect timer error Reload t
17 Shock result time out Reload t
18 USB interrupt error 1. Clea2. Rep
A01 System PCB
P Back Index Next Page
LIF Troubleshooting
U
AcSt
s options that provide information such as rrors, and counters for shock and pacing
nu, access the SERVICE menu and select
s log
nters
ement memory
(Continued on next page)
6-41
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
sing the Service/Status Features
cessing the Service/atus Features
The SERVICE/STATUS submenu includestored manufacturing data, recorded eoperation.To display the SERVICE/STATUS submeSTATUS.The SERVICE/STATUS options include:
Option Description
Device Log Show device statu
Device Data Show device data
Service Log Show service log
Counters Display shock cou
Clear Memory Clear data manag
P Back Index Next Page
LIF Troubleshooting
U
De ATUS submenu to view essential device rating software was installed, and as the shock count.ing information:
en the device was manufactured, hen the operating software was loaded.
ether there are any error codes stored in og (refer to Processing Service Codes).
of times the device has been powered on.
pulses delivered by the device.
e device defibrillation capacitor has been
power-on time.
running time.
unning time.
(Continued on next page)
6-42
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
sing the Service/Status Features (continued)
vice Log Select DEVICE LOG on the SERVICE/STcharacteristics, such as when the opeaccumulative device operations, suchThe device log data includes the follow
Data Description
Manufacturing date The date whspecifically, w
Fault Messages Indicates whthe Service L
Power Cycle Count The number
Pacing Count Total pacing
Shock Count Total times thcharged.
Power On Time Total device
Printer On Time Total printer
SpO2 Operating Time Total SpO2 r
P Back Index Next Page
LIF Troubleshooting
U
De TATUS submenu to view essential device ber, and accumulative device operations,
l number
number
was built
mbly hardware serial number
mbly software version number
meter PCB hardware serial number
meter PCB software version number
ardware serial number
troller hardware serial number
(Continued on next page)
6-43
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
sing the Service/Status Features (continued)
vice Data Select DEVICE DATA on the SERVICE/Scharacteristics, such as the serial numsuch as the shock count.The device data includes:
Data Description
Serial Number Device seria
Dash Number Device dash
Manufacture Date Date device
Power HW Power asse
Power SW Power asse
PP HW Patient para
PP SW Patient para
OEM HW OEM PCB h
SC HW System con
P Back Index Next Page
LIF Troubleshooting
U
De(c
troller software version number
troller voice prompt version
B hardware serial number
B software version number
ce hardware serial number
ce software version number
ce field programmable E program
are serial number
re version number
(Continued on next page)
6-44
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
sing the Service/Status Features (continued)
vice Data ontinued) Data Description
SC SW System con
SC Voice System con
Therapy HW Therapy PC
Therapy SW Therapy PC
UI HW User interfa
UI SW User interfa
UI FPGA User interfa
SpO2 HW SpO2 hardw
SpO2 SW SpO2 softwa
P Back Index Next Page
LIF Troubleshooting
U
Se ATUS submenu to view the device service
information:
entries (service codes)
rvice log
ervice log
(Continued on next page)
6-45
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
sing the Service/Status Features (continued)
rvice Log Select SERVICE LOG on the SERVICE/STrecord.The service log includes the following
Data Description
Service dates Service log
PRINT LOG button Prints the se
CLEAR LOG button Clears the s
P Back Index Next Page
LIF Troubleshooting
U
Co TUS submenu to view the joule settings, ince the last reset, and the total number of t into operation.L. This resets the boxed subtotal counters can also reset the counters using the the next page.
(Continued on next page)
6-46
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
sing the Service/Status Features (continued)
unters Select COUNTERS on the SERVICE/STAthe total number of shocks delivered sshocks delivered since the device wenTo reset the counters, select CLEAR ALbut not the running-total counters. YouCLEAR MEMORY feature discussed on
P Back Index Next Page
LIF Troubleshooting
U
Cl /STATUS submenu to clear the flash data ory PCB. A count-down timer appears to
quires approximately 30 seconds.
(up to 45 minutes of first-in-first-out ermanently deleted.t reports are permanently deleted.hen the device is placed into new or
s no longer required. The data as part of some service actions.t memory is permanent; there is no undo. before clearing the memory, print the the Data Management section in the
6-47
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
sing the Service/Status Features (continued)
ear Memory Select CLEAR MEMORY on the SERVICEmanagement memory on the A02 Memindicate the clearing process, which reSpecifically, it clears the following:■ ECG data — All stored ECG data
continuous ECG waveforms) are p■ Patient reports — All stored patienClear the data management memory wdifferent use and the old patient data imanagement memory is also cleared Note: Clearing the data managemen
To save important patient dataindividual patient data (refer tooperating instructions.
P Back Index Next Page
LIF Troubleshooting
S
icate the presence of errors in the Service ates when a service code is written to the vice Codes to resolve the problem.uminates when you turn on the device, a ervice Log. If you cycle the power, and the gain, it does not mean that there are no view the Service Log and resolve the the first instance.
6-48
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Indicator
The service indicator LED does not indLog. The service indicator LED illuminService Log. Refer to Processing SerFor example, if the service indicator illservice code has been written to the Sservice indicator does not illuminate acodes in the Service Log. You must reservice code that was written there in
P Back Index Next Page
LIF Troubleshooting
D
of self-tests occur. If errors are detected, Self-testing does not occur only at vice is turned on.cting USER TEST does not initiate a est status and produces reports. The le is complete and then reports USER TEST
NS/USER TEST feature. This operation efibrillator capacitor to 10 joules and then oes not pass, the service indicator LED e Service Log (refer to Processing
6-49
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
evice User Test
When you turn on the device, a seriesthe service indicator LED illuminates. power-on; it is continuous while the dePressing the OPTIONS button and seleself-test cycle; rather, it monitors self-tdevice waits until the next self-test cycPASSES. One operation is specific to the OPTIOconsists of one cycle of charging the ddumping the charge. If this operation dilluminates and an error is written to thService Codes).
P Back Index Next Page
LIF Troubleshooting
D
is replaced, then reloading of device is required. le software programs maintained on the efibrillator/monitor, know as a device
is documented as a single software software will maintain the device at a re set.sing the LIFENET System Asset ur local Physio-Control service or sales
6-50
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
evice Printed Circuit Board Replacement
Anytime a printed circuit board (PCB) system software to the current versionThe device system software are multipcircuit boards within the LIFEPAK 20 dsoftware set. This device software setversion and part number. Updating theknown released device system softwaDevice Software set can by install by umanagement tools or by contacting yorepresentative.
LIF Section Contents
P Back Index Next Page
PM
d testing of the device helps detect and anical problems. When scheduled e MAINTENANCE DUE message displays for the device is turned on (if a maintenance aintenance interval, refer to Setting a esetting the Maintenance Prompt.
topics, refer to Battery Maintenance. The e following:
uidelines
EPAK 20/20e Defibrillator/Monitor
revious Page Table of Contents
9reventive aintenance
Periodic maintenance, inspection, anprevent possible electrical and mechmaintenance is due for the device, thapproximately 10 minutes each time interval is set). To set and reset the mMaintenance Prompt Interval and RFor information about battery-relatedinformation in this section includes th
Maintenance and Testing GCleaningDevice Useful LifeSupport PolicyStoring the DeviceRecycling
P Back Index Next Page
LIF Preventive Maintenance
M
d testing of the device will help prevent oblems. Refer to the Operator Checklist in al items.le for preventive maintenance activities.
regular intervals, refer to scheduled
As Needed Scheduled
re (PIP) X Annually
TCP) X
X
X
X
X
5 years
life X
7-2
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
aintenance and Testing Guidelines
Periodic maintenance, inspection, anpossible electrical and mechanical prthe operating instructions for additionThe following table shows the scheduFor items that should be replaced at replacement Items shown below.
Activity
Performance inspection proceduTest and calibration procedures (Exterior physical inspectionInterior Physical InspectionExterior cleaningInterior cleaningCoin battery replacementA07 battery replacement (serviceminimum of 2 years)
P Back Index Next Page
LIF Preventive Maintenance
C
ClM
need to perform an external and internal w.
Description
Grounded conductive surfaceand wrist strap
Nonmetallic
Clean and lint-free
Clean and dry (60 psi, maximum)
7-3
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
leaning
eaning Tools and aterials
The tools and materials that you will cleaning of the device are listed belo
Product
Static-discharge-protected work area
Isopropyl alcohol
Quaternary ammonium compounds
Peroxide (peracetic acid) solutions
Cotton swabs
Vacuum cleaner
Soft-bristle brush
Cloth
Compressed air
P Back Index Next Page
LIF Preventive Maintenance
C
ExPr rse or soak any portion of this device in
ling any fluid on the device or
n any part of this device or accessories enolic compounds. Do not use abrasive ot attempt to sterilize this device or any
cified in the accessory operating
iping the surface with any of the following
ds
s
7-4
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
leaning (continued)
ternal Cleaning ocedure
WARNING!Shock or fire hazard. Do not immewater or any other fluid. Avoid spilaccessories.
CAUTION!Possible case damage. Do not cleawith bleach, bleach dilution, or phor flammable cleaning agents. Do naccessories unless otherwise speinstructions.
Clean the exterior of the device by wsolutions:■ Soap and water■ Quaternary ammonium compoun■ Isopropyl alcohol■ Peroxide (peracetic acid) solution
P Back Index Next Page
LIF Preventive Maintenance
C
SpPr
t it from the patient cable and clean the propyl alcohol pad. Allow the sensor to dry
ith a 70% isopropyl alcohol pad and erse the cable in any liquid solution. Do not
7-5
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
leaning (continued)
O2 Cleaning ocedure
To clean the SpO2 sensor, disconnecLNOP DCI by wiping it with a 70% isobefore placing back in use.Clean the patient cable by wiping it wallowing it to dry. Do not soak or immattempt to sterilize.
P Back Index Next Page
LIF Preventive Maintenance
C
InPr capacitor carries high voltage. Remove
citor before handling.
n any part of this device or accessories enolic compounds. Do not use abrasive ot attempt to sterilize this device or any
cified in accessory operating
scribed below. with a nonmetallic, soft-bristle brush.sing a dry, low-pressure compressed air
onabrasive cloth that has been dampened
7-6
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
leaning (continued)
ternal Cleaning ocedure
WARNING!Shock hazard. The energy storagethe battery and discharge the capa
CAUTION!Possible case damage. Do not cleawith bleach, bleach dilution, or phor flammable cleaning agents. Do naccessories unless otherwise speinstructions.
Clean the interior of the device as de1. Brush interior surfaces and parts2. Remove loosened dirt and dust u
(60 psi) or vacuum cleaner.3. Wipe metal surfaces with a soft, n
with isopropyl alcohol.
P Back Index Next Page
LIF Preventive Maintenance
D
ice and subassemblies are subjected to the routine testing and maintenance e manual will help provide reliable device
anges and the availability of replacement medical devices. The American Hospital ful life expectancy for defibrillators le Hospital Assets, Revised 1998 Edition). -year life expectancy for defibrillators nditure Limits for Medical Materiel, TB
Su support and replacement parts for a period nt from our manufacturing facility. After this vides technical support and replacement
7-7
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
evice Useful Life
During product development, the devrigorous life testing. This testing and program recommended in this servicoperation for many years.However, both rapid technological chparts limit the useful life of all modernAssociation suggests a five-year use(Estimated Useful Lives of DepreciabSimilarly, the U.S. Army lists an eight(technical bulletin: Maintenance ExpeMED 7 Revision 8 October 1993).
pport Policy Physio-Control provides full technicalof eight years from the date of shipmeeight-year period, Physio-Control proparts on an as-available basis.
P Back Index Next Page
LIF Preventive Maintenance
S
ds of storage, connect the device to ac rge the batteries at an ambient room ° F), prior to storage and before use.e without turning off the AC Loss Alert
AC that beeps when the device is turned off urce. The alarm can be configured to beep t can be turned off. The default setting is
menu. ETUP/GENERAL submenu. MINUTES, or NEVER ALERT to set or turn off
7-8
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
toring the Device
When not in use, or during long periopower. If this is not possible, fully chatemperature, not to exceed 25° C (77Note: Do not store or ship the devic
alarm.
Loss Alert Alarm The device is equipped with an alarmand not connected to an ac power soat 5-, 15-, or 30-minute intervals, or i15 minutes.To set or disable the alarm:1. Display the SETUP menu. 2. Select GENERAL from the SETUP 3. Select AC LOSS ALERT from the S4. Select 5 MINUTES, 15 MINUTES, 30
the alarm.
P Back Index Next Page
LIF Preventive Maintenance
R
seful life. the device according to national and local ysio-Control representative for assistance
com/recycling. be clean and contaminant-free prior to
— After using disposable electrodes, follow recycling.iscarding/Recycling Batteries.ckaging materials.
7-9
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ecycling
Recycle the device at the end of its u■ Recycling assistance — Recycle
regulations. Contact your local Phor refer to www.physio-control.
■ Preparation — The device shouldbeing recycled.
■ Recycling disposable electrodes your local clinical procedures for
■ Recycling batteries — Refer to D■ Packaging — Save or recycle pa
LIF Section Contents
P Back Index Next Page
BM
is section to help maximize battery life and
ry
ries
EPAK 20/20e Defibrillator/Monitor
revious Page Table of Contents
10attery aintenance
Follow the guidelines described in thperformance.
Types of BatteriesCharging the Backup BatteStoring the BatteryDiscarding/Recycling Batte
P Back Index Next Page
LIF Battery Maintenance
Ty
or the device. in the bottom case. itor uses a 10-cell, nickel metal hydride
nitor uses a 9-cell, lithium-ion (Li-ion)
itor battery will not be charged or may other than a Physio-Control battery is
d as the primary power source. If the e to power outage or other reason, the for at least two hours.ry that delivers a continuous flow of power ories. This battery has a greater than five-nd should be replaced at the end of its life.
8-2
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
pes of Batteries
AC power is the main power source fThere is one backup battery located ■ The LIFEPAK 20 defibrillator/mon
(NiMH) battery.■ The LIFEPAK 20e defibrillator/mo
battery.
WARNING!The LIFEPAK 20e defibrillator/monbe charged incorrectly if a battery used.
This battery is not intended to be useprimary power source is removed, dubackup battery will power the device The device also has a coin cell batteto the internal clock and other accessyear life span. It is not rechargeable a
P Back Index Next Page
LIF Battery Maintenance
C
has a built-in, high-current charger that ackup battery in approximately two hours evice. The charger does not recharge the nce the battery’s last full recharge or until nd then reconnected.r has a built-in, constant, current-constant pletely discharged backup battery in wer is connected to the device. The y until the Li-ion battery's state-of-charge
r/monitor will only initiate battery charging if C. If extensive defibrillator shocks have high ambient temperature, the battery will g.
8-3
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
harging the Backup Battery
The LIFEPAK 20 defibrillator/monitorrecharges a completely discharged bwhen ac power is connected to the dbattery until one week has passed sithe battery has been disconnected aThe LIFEPAK 20e defibrillator/monitovoltage charger that recharges a comapproximately four hours when ac pocharger does not recharge the batterdrops below 85%. Note: The LIFEPAK 20e defibrillato
the battery pack is below 40°been applied to a device in anot immediately start chargin
P Back Index Next Page
LIF Battery Maintenance
S
in storage when it is not in active use.andling procedures for storage. Store the 0° C (-4° F and 122° F). Lower tial charge.
8-4
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
toring the Battery
A battery packet is considered to be The battery packet requires special hbattery packet between -20° C and 5temperatures reduce the battery’s ini
P Back Index Next Page
LIF Battery Maintenance
D
at end of its useful life if one or more of the
battery.
ss of full charge capacity.al and local regulations. Contact assistance at 1.800.442.1142, or refer to for disposal instructions.
Do not recharge, disassemble, crush, te, or mistreat batteries.
8-5
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
iscarding/Recycling Batteries
A battery should be considered to befollowing circumstances occur:■ There is physical damage to the ■ The battery is leaking.■ The battery charges to 80% or leRecycle batteries according to nationPhysio-Control Technical Support forwww.physio-control.com/recycling
WARNING!Risk of fire, explosion, and burns. heat above 100°C (212°F), incinera
LIF Section Contents
P Back Index Next Page
RP
f detailed instructions for disassembly, ble LIFEPAK 20/20e defibrillator/monitor
ever the device case is opened for service. harnesses, label the cables and y during reassembly (for example, J1, J3, for additional information.
es, item numbers in parentheses refer to Parts List.
rge Toolation
(Continued on next page)
EPAK 20/20e Defibrillator/Monitor
revious Page Table of Contents
11eplacement rocedures
Replacement procedures are a set ohandling, and reassembly of replaceaassemblies.Perform an interior inspection whenWhen disconnecting cables and wireconnections so that they match easiletc.). See the Interconnect DiagramNote: Within replacement procedur
parts that are in the section’s
Repair Procedures IndexWarnings and CautionsRoHS StandardsCapacitor Discharge ToolUsing the Capacitor DischaSaving the Setup ConfigurMain Assemblies
LIF Section Contents
P Back Index Next Page
RP(c
entrial Number
EPAK 20/20e Defibrillator/Monitor
revious Page Table of Contents
eplacement rocedures ontinued)
Interconnect DiagramBattery ReplacementTop CaseFront CaseBoardstackBottom CaseFinal AssemblyService Replacement KitsDevice Software ReplacemDevice Part Number and SeOrdering Parts
P Back Index Next Page
LIF Replacement Procedures
RCh n device disassembly order from left to rigB
ToP Top Case Installation
(Continued on next page)
FA Parts ListF Front Case RemovalF AED Door ReplacementW A15 Elastomer Keypad RemovalA A11 Active Display InstallationA W17 Backlight Inverter Cable DiagramsA n A05 User Interface PCB DiagramW W04 Speed Dial Assembly InstallationW W04 Speed Dial Assembly DiagramsW
9-3
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
epair Procedures Indexoose from the following replacement procedures (procedures are listed iht):attery Replacement
p Casearts List Top Case Removal
ront Casessembly Diagram (Front View) Assembly Diagram (Rear View)ront Case Disassembly Front Case Reassemblyront Case Installation Grounding Harness Orientation18 UI Flex Cable Removal W18 UI Flex Cable Installation15 Elastomer Keypad Installation A11 Active Display Removal08 Backlight Inverter PCB Diagram A11 Active Display Diagram05 User Interface (UI) PCB Removal A05 User Interface (UI) PCB Installatio18 UI Flex Cable Diagrams W04 Speed Dial Assembly Removal02 Speaker Assembly Removal W02 Speaker Assembly Installation02 Speaker Assembly and W25 Speaker Harness Extension Cable Diagrams
P Back Index Next Page
LIF Replacement Procedures
R
(Continued on next page)
BA Parts ListB Boardstack Removal
B W07 Capacitor Discharge Cable Diagram
A A10 SpO2 Module Installation
A A02 Patient Parameter and A06 OEM/SpO2 Assembly Installation
A A01 System PCB RemovalA A04 Therapy PCB Removal
A g) A04 Therapy PCB Diagram (Without Pacing)
9-4
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
epair Procedures Index (continued)
oardstackssembly Diagram A04 Therapy PCB Assembly Diagramoardstack Disassembly Boardstack Reassembly
oardstack Installation W07 Capacitor Discharge Cable Replacement
14 Inductive Resistor Diagram A10 SpO2 Module Removal
10 SpO2 Module Diagram A02 Patient Parameter and A06 OEM/SpO2 Assembly Removal
02 Patient Parameter PCB Diagram Coin Cell Battery Replacement01 System PCB Installation A01 System PCB Diagram
04 Therapy PCB Installation A04 Therapy PCB Diagram (With Pacin
P Back Index Next Page
LIF Replacement Procedures
R
(Continued on next page)
BA Parts List B A12 Printer Module RemovalA A13 Energy Capacitor RemovalA A03 Power Module InstallationA s W06 ECG Connector RemovalW ms W01 Therapy Connector Removal
W W01 Therapy Connector Assembly Wiring Diagram
W W05 SpO2 Assembly DiagramsW W03 IrDA Assembly DiagramsW
9-5
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
epair Procedures Index (continued)
ottom Casessembly Diagram (Modules) Assembly Diagram (Connectors)ottom Case Disassembly Bottom Case Reassembly12 Printer Module Installation W14 Printer Flex Cable Diagrams13 Energy Capacitor Installation A03 Power Module Removal03 Power Module Diagram W11 ECG Sync/System Cables Diagram06 ECG Connector Installation W06 ECG Connector Assembly Diagra
01 Therapy Connector Installation W01 Therapy Connector Assembly Diagrams
05 SpO2 Connector Removal W05 SpO2 Connector Installation03 IrDA Assembly Removal W03 IrDA Assembly Installation25 Speaker Harness Extension Cable
RemovalW25 Speaker Harness Extension CableInstallation
P Back Index Next Page
LIF Replacement Procedures
R
FD
Manual Latch Label Languages
A A15 Elastomer Keypad - LanguagesIS Charge Button Languages
9-6
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
epair Procedures Index (continued)
inal Assemblyevice Labeling Including Label Set (12) 3201640 - LIFEPAK 20 3206034 - LIFEPAK 20e
LIFEPAK 20/20e Device Label Set Languages
ED Door/Latch Label Kits A15 Elastomer Keypad – All Optionsnstalling Printer Paper Standard Paddles Labels and Buttonstandard Paddles Parts List Standard Paddles Label Languages
P Back Index Next Page
LIF Replacement Procedures
W
utions apply to all actions you may ice.
e must be performed by properly trained ntially lethal charges accessible inside the the procedures carefully for discharging the
oltage. Discharge the capacitor before
during reassembly. To avoid pinching wires, .
PCB assemblies contain static-sensitive bserve the special handling practices vices (SSD).
9-7
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
arnings and Cautions
The following general warnings and caperform during maintenance of the dev
WARNINGSHOCK HAZARD. Servicing of this devicindividuals. This device may retain potedevice at any time, even when off. FollowA13 Energy Capacitor.
The A13 Energy Capacitor carries high vhandling.
It is possible to pinch and damage wirescarefully follow reassembly instructions
CAUTIONPossible component damage. Thedevices (SSDs). To avoid damage, odescribed under Static-Sensitive De
P Back Index Next Page
LIF Replacement Procedures
R
Ab w directive which applies to all medical s 2011/65/EU of the European ly referred to as “RoHS 2” (Restriction of
requires companies to restrict the use of ir products (such as lead, mercury, etc.).0e device have been updated to comply h RoHS-certified and non-RoHS parts
rts are functionally equivalent. However, the following RoHS vs Non-RoHS Parts rts to order. 20e devices that are RoHS compliant can ber label. The product part number for a number of 300 or greater.
9-8
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oHS Standards
out RoHS Parts The European Union has initiated a nedevices sold in Europe. This directive iParliament and the Council, commonHazardous Substances). The directivecertain substances in the design of theSome of the parts in the LIFEPAK 20/2with this standard. For these parts, botmay be listed. RoHS-certified parts and non-RoHS pawhen ordering parts replacement, use Replacement Rules to decide what paRoHS Device Identification—LIFEPAKbe identified by the product serial numRoHS version is 3202488 with a dash
P Back Index Next Page
LIF Replacement Procedures
R
Ab(c
lesNon-RoHS Country (ROW)
IR
RoHS or non-RoHS equivalent parts can be used to service any device
IL
RoHS or non-RoHS equivalent parts can be used to service any device
RL
It is OK to put a non-RoHS accessory on a RoHS device. Existing inventory will be depleted and replaced by RoHS compliant accessories
9-9
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oHS Standards (continued)
out RoHS Parts ontinued)
RuSituation RoHS Country (Europe)
f replacing parts in a LP20e oHS device
ALL parts must be RoHS
f replacing parts in a LP20e or P20 non-RoHS device
RoHS or non-RoHS equivalent parts can be used until inventory is exhausted
eplacing accessories on a P20e or LP20 device
It is OK to put a non-RoHS accessory on a RoHS device. Existing inventory will be depleted and replaced by RoHS compliant accessories
P Back Index Next Page
LIF Replacement Procedures
S
Ab s (such as MOS ICs, FETs, optical aged by the discharge of static electricity. Static discharges commonly occur when nd transfers the charge to any object e or destroy static-sensitive devices s not even perceptible to the person who
SSDs, observe the following precautions e, or repair procedures:
Th arning symbol:
on a static-dissipative mat that is
(Continued on next page)
9-10
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
tatic-Sensitive Devices (SSD)
out SSD Handling Many electronic semiconductor deviceisolators, or film resistors) can be damStatic-charge buildup is very common.the operator wears synthetic clothes atouched. These discharges can damag(SSDs). In most cases, the discharge icauses it.To prevent static-discharge damage toduring any open-case test, maintenanc
e SSD Symbol SSDs are identified with the following w
Always perform repair or maintenanceconnected to earth ground.
ATTENTION
P Back Index Next Page
LIF Replacement Procedures
S
W ap connected to the mat and to ground equipment or when discharging high snug enough to make good contact
TrPC
racks or inside conductive bags. Label static-sensitive.
KeSt
as styrofoam cups or trays, away from the ment, such as test equipment, to ground
TeRo
(mat, straps, cables) routinely. Keep a
trap when working on energized equipment or ts.
9-11
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
tatic-Sensitive Devices (continued)
ear a Wrist Strap • Always wear a conductive wrist strexcept when working on energizedvoltage circuits. The strap must beagainst bare skin.
ansport and Store Bs Properly
Transport and store PCBs in anti-staticthe package that contains the PCBs as
ep Work Area atic-Free
Keep static-generating products, such work area. Connect all electrical equipwith a three-prong plug.
st Work Area utinely
Test all antistatic parts of the work arealog of the test results.
WARNINGSHOCK HAZARD. Remove the wrist swhen discharging high-voltage circui
P Back Index Next Page
LIF Replacement Procedures
A
To PAK 20/20e defibrillator/monitor
pags
on about Capacitor Discharge Tool)rque settings are 6.8 and 10.0 in-lb.
s tip for 4-40 screws (shaft length of 2”)s tip for 6-32 screws (shaft length of 2”)
Values10.0
160
113
9-12
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ssembly Tools List
ols List The suggested list of tools for the LIFEreplacement procedures is as follows:■ Static-dissipative mat and wrist stra■ Anti-static rack and/or conductive b■ Capacitor discharge tool (informati■ Torque screwdriver(s) - required to
■ Point 1 power drive bit (P1)- Phillip■ Point 2 power drive bit (P2)- Phillip■ 3/32” Allen Driver■ 1/4” Nut Driver
Torque MeasurementsTorque in-lb 6.8
Torque in-oz 108.8
Torque cNm 77
P Back Index Next Page
LIF Replacement Procedures
C
e tools are available. Contact a Technical ation.
sic capacitor discharge tool is constructed e Capacitor. The materials used in this
, high-voltage
ulating 10 kV
rgy storage capacitor, continue to the
t are not designed and labeled for biphasic c defibrillators. They will take several minutes
5r
9-13
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
apacitor Discharge Tool.
Third party biphasic capacitor dischargSupport Representative for more informShown is an example of how the biphafor discharging the A13 Energy Storagexample are:■ 10 k, 2 W resistor (ten 1 K 2 W)■ 5 M, 5 W resistor, high-voltage■ Neon lamp, NE76, NE2, or NE2H■ 8 AWG copper wire■ Clear plastic tubing, capable of ins■ 10 kV insulation■ RTV, silicone rubber sealantFor instructions on discharging the enenext page.
WARNINGSHOCK HAZARD. Discharge tools thause are inadequate for use on biphasito discharge the energy capacitor.
RTV silicone rubber sealant
10K 2W resistor
RTV silicone rubber sealant
10 kV insulation
8AWG wire
Neon lamp
M5W esistor
Clear plastic tubing
6 inches
P Back Index Next Page
LIF Replacement Procedures
U
discharge the energy storage capacitor the inner parts of the device.
t on the inductive resistor and hold it ext page).tion point of the capacitor wire. Hold both
capacitor discharge tool. If a charge of the neon lamp will light.
t are not designed and labeled for biphasic c defibrillators. They will take several minutes
(Continued on next page)
9-14
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
sing the Capacitor Discharge Tool.
The capacitor discharge tool is used tobefore beginning any maintenance on To use the capacitor discharge tool:1. Remove the battery. 2. Remove the top case.3. Place one probe on the solder join
steady (see the illustration on the n4. Place the other probe in the connec
probes steady.5. Observe the neon lamp inside the
approximately 90 volts is present,
WARNINGSHOCK HAZARD. Discharge tools thause are inadequate for use on biphasito discharge the energy capacitor.
P Back Index Next Page
LIF Replacement Procedures
U )
e points indicated for at least 30 seconds .
capacitor is discharged if the neon lamp does on the capacitor. Do not touch capacitor rge operation.
Pin 5 on the A04 Therapy PCB P2 connector. See the Interconnect Diagram for more detail.
9-15
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
sing the Capacitor Discharge Tool (continued.
6. Continue holding the probes on thafter the neon lamp is no longer lit
WARNINGSHOCK HAZARD. Do not assume thenot light! There may still be a chargeterminals until completing the discha
Solder point on inductive resistor
Capacitor discharge cable connection point
Capacitor discharge cable passes under the W01 Therapy Cable and wraps around the J13 connector.Position the therapy cable ferrites so that they will not damage the J13 connector
Back Index Next Page
Replacement Procedures
to save the device setup configuration
System account, then use the LIFENET e setup configurations.etup configuration to a spare device, r the setup configuration back again. p configuration, complete repairs, and
ce.nsferring it to a spare device requires that ftware version. Otherwise, potentially when the configuration is restored to the yright dates are the same on the es.
9-16
Previous Page Table of Contents Section Contents
LIFEPAK 20/20e Defibrillator/Monitor Saving the Setup Configuration
The following procedures describe howbefore beginning any repair action. ■ If the device owner has a LIFENET
Device Agent application to manag■ Another method is to transfer the s
complete repairs, and then transfe■ The final method is to print the setu
then manually reconfigure the deviNote: Saving the configuration by tra
both devices have the same sounexpected results may occur repaired device. Verify that copintroduction page of both devic
Back Index Next Page
Replacement Procedures
spare device:es, connect the two devices using a 202447) between the device system
evices.menu on the device to be repaired. The
DIAL. The setup configuration transfers to
P menu on the device to be repaired. The figuration. Save this backup printout for
ransferring it back to the repaired device: saved setup configuration) to the
ion transfer cable (P/N 3202447) between
(Continued on next page)
9-17
Previous Page Table of Contents Section Contents
LIFEPAK 20/20e Defibrillator/Monitor Saving the Setup Configuration (continued)
Transferring the Setup Configuration
To transfer the setup configuration to a1. With the power OFF on both devic
configuration transfer cable (P/N 3connectors.
2. Display the SETUP menu on both d3. Select SEND CONFIG in the SETUP
SEND CONFIG overlay appears. 4. Select SEND and press the SPEED
the spare device.5. Select PRINT DEFAULTS in the SETU
printer prints the device setup conpossible future reference.
6. Turn both devices OFF.
Restoring the Setup Configuration
To restore the setup configuration by t1. Connect the spare device (with the
repaired device using a configuratthe device system connectors.
Back Index Next Page
Replacement Procedures
evices.enu on the spare device. The SEND
DIAL. The setup configuration transfers
r prints the device setup configuration. ce.
e SETUP menu.gs in each menu and revise as necessary
9-18
Previous Page Table of Contents Section Contents
LIFEPAK 20/20e Defibrillator/Monitor Saving the Setup Configuration (continued)
2. Display the SETUP menu on both d3. Click SEND CONFIG in the SETUP m
CONFIG overlay appears.4. Select SEND and press the SPEED
back to the repaired device.5. Turn both devices OFF.
Printing the Setup Configuration
To print the setup configuration:1. Display the SETUP menu.2. Select PRINT DEFAULTS. The printe
Save this printout for future referen3. Turn the device OFF.4. Make the necessary repairs.5. Turn the device ON and display th6. Using the printout, check the settin
to match the printout. 7. Turn the device OFF.
P Back Index Next Page
LIF Replacement Procedures
M
Printer Module
Power Module
Fr
9-19
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ain Assemblies
Interconnect
Top Case Assembly
Boardstack Assembly
Bottom Case Assembly
ont Case Assembly
P Back Index Next Page
LIF Replacement Procedures
In
A08 Backlight Inverter PCB
Power Module
A12 Printer
A11 LCD Display PCB
W09 W10LP20e
W11
W14W01
W23 W24
W22W21W20
W15
W17
W19
A05 User Interface PCB
J37 J36 J34P34P37
P14J14
P13J13
J17P17P16
J16
J45
J47 P47
P45
P41 P51
P70
P74PCB Shield
Display Bracket
Printer Shroud
J81 TherapyPower BracketHeatsink
PCB Bracket
J48RS-232
J49Sync inECG out
J2
CN101
J39 Test
J38 Test
J1
J51J41
9-20
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
terconnect Diagram
A10 SpO2 PCB
A06 OEM PCB
A02 Patient Parameter PCB
A01 System PCB
A04 Therapy PCB
A19 EMI Line Filter
A03
A13 Energy Capacitor A14 Inductor/Resistor
W08LP20e
W18 UI FlexW06
W03 W25 W02
W12
W04W05
A09 AC Power Supply
A07 Battery
J03
J52J01J53
P24
J24
J54 P54
J32P32 J31
P23J23 J21 J22
P31
P21
J01 J02
J02J01
J11 J12J01P01P02
J02J15
J03
J08P08 P05
J05
P06 P07IrDA
P03
ECG 8-Pin Conn.
J21 J22
J50P50
P85J85
J01 P61
P62J02
J46 AC Power
P49
Cap Discharge
J80Gnd Stud
W13LP20e
Speaker
J83 SpO2
Speed Dial J82 ECG
J33 Test
W07
J49
P
LIF Replacement Procedures
9-21Ba
A0Re
r the A07 Batteries. The LIFEPAK 20e
PAK
tery
Batt
Back Index Next Page
07 Battery with the 6-pin connector, and nitor uses the battery with the 4-pin
Battery from the device:er.
drivers into the door taps and pinch the 3).attery.
the A07 Battery.ery compartment. (For the LIFEPAK 20 ward the rear of the device.) compartment with the wire harness
e.
PIP.
Main Assemblies
revious Page Table of Contents Section Contents
E 20/20e Defibrillator/Monitor
t Replacement
7 ery placement
Note: There are two different types fodefibrillator/monitor uses the Athe LIFEPAK 20 defibrillator/moconnector. To remove the A07
1. Disconnect the device from ac pow2. Place the device top down.3. Insert two, small, flat-bladed screw
tabs to remove the battery door (104. Remove and disconnect the A07 BTo install the A07 Battery:1. Place the device top down.2. Connect the W08 Battery Cable to3. Insert the A07 Battery into the batt
battery, ensure the fuse is facing toNote: Install the A07 Battery in thefacing toward the front of the devic
4. Close the battery door (103).5. Complete the LIFEPAK 20 Device
103A07Battery
Parts List Modules View
P Back Index Next Page
LIF Replacement Procedures
To
Toer.
e device.
0.375 screws (169) securing the bottom
75 screws (167) securing the bottom case
1.75 screws (167) securing the top case ).m the top case, and slide the top case up ce.
ain Assemblies
9-22
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
p Case
p Case Removal To remove the top case:1. Disconnect the device from ac pow2. Remove the A07 Battery from th3. Place the device face down.4. Remove and discard the two 6-32
case to the front case.5. Remove and discard the 6-32 1.
to the top case.6. Place the device on its bottom.7. Remove and discard the two 6-32
to the front case (outboard screws8. Pull the front case slightly away fro
and away from the rest of the devi9. Discharge the A13 Capacitor.
169
167
167
Parts List M
P Back Index Next Page
LIF Replacement Procedures
To
Tocase.tom case..
se with two new 6-32 1.75 screws (167);
ure the front case to the bottom case with ); torque to 10 in-lb.m case with two new 6-32 1.75 screws
vice.nstall new labels. PIP.
24
Main Assemblies
9-23
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
p Case (continued)
p Case Installation To install the top case:1. Align the front case to the bottom 2. Align the top case (242) to the bot3. Align the front case to the top case4. Secure the top case to the front ca
torque to 10 in-lb.5. Turn the device face down and sec
two new 6-32 0.375 screws (1696. Secure the top case onto the botto
(167); torque to 10 in-lb.7. Install the A07 Battery into the de8. Review the labels parts list and i9. Complete the LIFEPAK 20 Device
169
167
167
2
Parts List
P Back Index Next Page
LIF Replacement Procedures
To
Pa
It tion Note
1 ws 6-32 × 1.75L
1 w, 6-32 × 0.375L
2 embly
9-24
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
p Case (continued)
rts List
em Quantity MIN CAT. Part Descrip
67 4 202253-592 21300-005334 Machine scre
69 2 202253-570 21300-001032 Machine scre
42 1 3202497-002 21330-001036 Top case ass
P Back Index Next Page
LIF Replacement Procedures
F
As(F
Rear View Main Assemblies
A15
37
199
23
19
without door optionFrFrA(1WRWInARAIn
9-25
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case
sembly Diagram ront View)
Parts A05–W18 Parts 9–47 Parts 161–284
912-D
W04
17
12-B12-C
Hardware suppliedwith item W04
ont Case Removal (9)ont Case Installation (9)ED Door Replacement 99)04 Speed Dial Assembly emoval 04 Speed Dial Assembly stallation15 Elastomer Keypad emoval15 Elastomer Keypad stallation
12-Bno SpO2
w/ SpO2
284
P Back Index Next Page
LIF Replacement Procedures
F
As(R
Pa ront Case View Main Assemblies
Detail A
9 Ref 201 only used
A1A1A0ReA0InWWInGr
41 W04
9
A05
173 (x4)
161 (x3)see Detail A
221
240
219 250W02
(x2)
with A08- 3202033
9-26
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
sembly Diagramear View)
rts A05–W18 Parts 9–47 Parts 161–284 F
A08
47
A11
43
266
173 (x4)
219 (x2)
1 Active Display Removal1 Active Display Installation5 User Interface (UI) PCB moval5 User Interface (UI) PCB
stallation02 Speaker Assembly Removal02 Speaker Assembly stallationounding Harness Orientation
173(x2)
3308907
P Back Index Next Page
LIF Replacement Procedures
F
Pa
(Continued on next page)
Pa Rear View Main Assemblies
Ite NoteA0 Part of kit MIN 3202718-044,
3202718-045, 3202718-046A0 T,
V inPart used with A11 - 3205278 Part of kit MIN 3202718-009
A0 ver Part used with A11 - 3309555 Part of kit MIN 3202718-032
A1 CD Part of kit MIN 3202718-008A1 ED Requires A05 - 3317230-002 or
greater and Redux Device S/WPart of kit MIN 3202718-032
A1 Select other language
9-27
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
rts List
rts W17–47 Parts 161–284 Front Case View
m Quantity MIN CAT. Part Description5 1 3317230-002 see note User Interface PCB
8 1 3202033 see note Backlight Inverter, CCFLCD, 1.5KV Out, 8to20
8 1 3308907 see note Module-OEM, LED Dri(Backlight Inverter)
1 1 3205278 see note Active Display, Color L
1 1 3309555 see note Active Display, Color L
5 1 3200642-XXX see note Elastomer Keypad
P Back Index Next Page
LIF Replacement Procedures
F
Pa
(Continued on next page)
Rear View Main Assemblies
It Note
W RoHS
W Non-RoHS
W
W able
W er Cable
W bly
9 Part of kit MIN 3202718-001
12 Refer to Labels Assembly
17
19 Part of kit MIN 3202718-001
23 Select other language
9-28
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
rts List (continued)
Parts A05–W15 Parts 161–284 Front Case View
em Quantity MIN CAT. Part Description
02 1 3319086-001 21300-008133 Speaker Assembly
02 1 3201593-004 21300-004247 Speaker Assembly
04 1 3201145-000 21300-004264 Speed Dial Assembly
15 1 3300152-000 21300-007774 Active Color Display C
17 1 3200996-002 21300-004237 Active Backlight Invert
18 1 3201000-004 21330-008056 UI to Stack Flex Assem
1 3200624 see note Front case
1 3206034-XXX see note Label set (6 labels)
1 3200633-000 21300-004620 Speed Dial knob
1 3200638-001 21300-004837 Cover plate, door
1 3201499-009 21501-000767 Manual latch label
P Back Index Next Page
LIF Replacement Procedures
F
Pa
P Rear View Main Assemblies
Ite Note
37 Part of kit MIN 3202718-001
41 ting
43 Part of various kits
47 Part of various kits
16
17 0.312L
19 Part of kit MIN 3202360
20 acklight
21 ss Active Display
22 ss User Interface PCB
9-29
(Continued on next page)
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
rts List (continued)
arts A05–W15 Parts W17–47 Front Case View
m Quantity MIN CAT. Part Description
1 3200637-001 21300-004836 Door hinge plate
1 3201610-000 21300-004649 Bracket, speaker moun
1 3200913-003 21300-004233 Display lens
1 3200640-015 21300-004838 Active display bracket
1 3 200805-000 21300-000584 Locking hex nut, 4-40
3 10 202253-761 21300-001038 Machine screw, 4-40
9 1 3202056-XXX see note AED door assembly
1 1 3201111-003 21300-004241 Thermally conductive binverter pad
9 3 3202246-003 21300-004254 Grounding strap harne
1 2 3202246-004 21300-004255 Grounding strap harne
P Back Index Next Page
LIF Replacement Procedures
F
Pa
Ite Note
24 Part of various kits
25 ss,
26 Part of various display kits
28 Refer to labels assembly
9-30
Rear View Main Assemblies
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
rts List (continued)
m Quantity MIN CAT. Part Description
0 1 804447-041 21300-004807 Spacer Foam, UI PCB
0 1 3202246-005 21300-004884 Grounding strap harneSpeed Dial
6 1 3205497-308 21300-006141 Nylon snap rivet
4 1 3206926-XXX see note Label - Adult VF Dose
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
FrDi evice.
ice is equipped with a door).
CB.embly.bly.ue to Front Case Reassembly.
ear View Main Assemblies
9-31
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
ont Case sassembly
To disassemble the front case:1. Remove the front case from the d2. Remove the AED door (if the dev3. Remove the A11 Active Display.4. Remove the A05 User Interface P5. Remove the W04 Speed Dial Ass6. Remove the W02 Speaker Assem7. Replace the front case and contin
Interconnect Front Case View R
P Back Index Next Page
LIF Replacement Procedures
F
FrRe ly.
B. bly.
d. is equipped with a door).
stall new labels.PIP.
ar View Main Assemblies
9-32
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
ont Case assembly
To reassemble the front case:1. Install the W02 Speaker Assemb2. Install the A05 User Interface PC3. Install the W04 Speed Dial Assem4. Install the A11 Active Display. 5. Install the A15 Elastomer Keypa6. Install the AED door (if the device7. Install the front case.8. Install the top case.9. Install the A07 Battery.10. Review the labels parts list and in11. Complete the LIFEPAK 20 Device
Interconnect Front Case View Re
P Back Index Next Page
LIF Replacement Procedures
F
Fr
citor.esses (219) that connect the A11 Active ort bracket by removing and discarding
ed grounding straps.oardstack assembly and disconnect the atient Parameter (PP) PCB at J21 and
assembly instructions to avoid a shock or
(Continued on next page)
Rear View Main Assemblies
9-33
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
ont Case Removal
To disassemble the front case:1. Remove the A07 Battery.2. Remove the top case.3. Discharge the A13 Energy Capa4. Disconnect the two grounding harn
Display to the top of the PCB suppthe two screws (173).Note: Replace any broken or fray
5. Pull the front case away from the bW18 UI Flex Cable from the A02 PJ22.
W18219
221
219
(x2)
173 WARNINGSHOCK HAZARD. Carefully follow disdamage to wires during disassembly.
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
Fr(c
esses (221) that connect the bottom left nterface (UI) PCB to the PCB support g the two screws (173). (219) that connects the bottom center of rt bracket by removing and discarding the
ess Extension Cable from the W02
able from the A05 UI PCB at J34.connector to access the printer connector.evice.
Rear View Main Assemblies
9-34
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
ont Case Removal ontinued)
6. Disconnect the two grounding harnand right corners of the A05 User Ibracket by removing and discardin
7. Disconnect the grounding harnessthe A05 UI PCB to the PCB supposcrew (173).
8. Disconnect the W25 Speaker HarnSpeaker Assembly.
9. Disconnect the W14 Printer Flex CNote: Disconnect the Speed Dial
10. Pull the front case away from the d
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
FFr
le to the A05 UI PCB at J34.s Extension Cable to the W02 Speaker
le if it was disconnected during the
s (221) by connecting the bottom left and the PCB support bracket, using two new efer to Grounding Harness Orientation
) by connecting the bottom center of the tem shield, using a new screw (173);
grounding harnesses must be installed at vice components.
(Continued on next page)
P Rear View Main Assemblies
9-35
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
ont Case Installation To install the front case assembly:1. Connect the W14 Printer Flex Cab2. Connect the W25 Speaker Harnes
Assembly.Note: Reconnect the SPEED DIAL cab
disassembly process.
3. Install the two grounding harnesseright corners of the A05 UI PCB toscrews (173); torque to 6.8 in-lb. Rfor grounding harness placement.
4. Install the grounding harness (219A05 UI PCB to the boardstack systorque to 6.8 in-lb.
W18219
221
219
(x2)
173
CAUTIONPossible component damage. Theprecise angles to avoid damaging de
arts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
Fr(c
the A05 UI PCB at J36.tor Lock on the A02 PP PCB.r the latch on the A02 PP PCB at CN101 the latch. ses (219) by connecting the top of the ng two new screws (173); torque to 6.8 in-rientation for grounding harness
y
Rear View Main Assemblies
9-36
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
ont Case Installation ontinued)
5. Connect the W18 UI Flex Cable to6. Unlatch the Display CN101 connec7. Install the W18 UI Flex Cable unde
connector until seated, then close 8. Connect the two grounding harnes
front case to the system shield, usilb. Refer to Grounding Harness Oplacement.
9. Return to Front Case Reassembl
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
GrOr
, and bottom case join correctly, align the and on the next page.
(Continued on next page)
Rear View Main Assemblies
B
C
E
D
9-37
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
ounding Harness ientation
To ensure that the top case, front casegrounding harnesses as shown below
Parts List Interconnect Front Case View
A
AB
CD
E
P Back Index Next Page
LIF Replacement Procedures
F
GrOr
Grounding Harness lug orientation
Active Display removed for clarity
Rear View Main Assemblies
9-38
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
ounding Harness ientation (continued)
219
221
Grounding Harness lug orientation219
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
AERe
be an easily replaceable, breakaway ntly comes off during use, follow step 3 of low.bly:
hinge pin center slightly away from the free of the hinge.
adhesive.
he door hinge plate (37) to the front case. hinge pin center slightly away from the into the hinge. Ensure that the hinge pins
Rear View Main Assemblies
9-39
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
D Door placement
The AED door assembly is designed toassembly. If the door assembly accidethe AED door installation procedure beTo remove the entire AED door assem1. Open the AED door.2. Use a small screwdriver to pry the
door assembly until the door slides3. Peel the hinge off the front case.4. Clean the front case to remove old
To install a new AED door assembly:1. Clean the hinge area.2. Expose the adhesive and secure t3. Use a small screwdriver to pry the
door assembly until the door slidessnap into the securing holes.
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
WRe
d before beginning this disassembly.
t the two grounding straps (219) that the system shield, by removing the two
n the grounding harnesses. If they are , the front case will not join with the rest of
away from the boardstack assembly, and from the A02 PP PCB at J21 and J22. from the A05 UI PCB at J31, and remove
Rear View Main Assemblies
9-40
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
18 UI Flex Cable moval
Note: The top case must be removeTo remove the W18 UI Flex Cable:1. From the system shield, disconnec
connect the top of the front case toscrews.Note: Observe the positioning onot reinstalled at the correct anglesthe device correctly.
2. Pull the front case slightly forward,disconnect the W18 UI Flex Cable
3. Disconnect the W18 UI Flex Cablethe cable from the device.
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
WIn orward and away from the boardstack
x Cable to the A05 UI PCB at J31.lex Cable during installation. Excessive
nnectors.Cable to the A02 PP PCB at J21 and J22, the connectors evenly to avoid possible
(219) by connecting the top of the front e two screws (173); torque to 6.8 in-lb.f the grounding harnesses. If they are , the front case will not join with the rest of
Rear View Main Assemblies
9-41
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
18 UI Flex Cable stallation
To install the W18 UI Flex Cable:1. With the front case pulled slightly f
assembly, connect the W18 UI FleNote: Avoid bending the W18 UI Fbending can damage wires and co
2. Carefully connect the W18 UI Flex ensuring that the pins connect withpin damage.
3. Connect the two grounding straps case to the system shield, using thNote: Observe the positioning onot reinstalled at the correct anglesthe device correctly.
4. Reassemble the top case.
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
A1Re
: front case.
A1In configurations to find the MIN (part
your device:
case, position the left and right bottom d flush against the bottom corners of the
nto the front case ensuring that it is flush s or gaps.
Rear View Main Assemblies
9-42
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
5 Elastomer Keypad moval
To remove the A15 Elastomer Keypad1. Peel the old keypad away from the2. Thoroughly clean the front case.
5 Elastomer Keypad stallation
To install the A15 Elastomer Keypad:1. Select one of the following device
number) for the correct keypad for– Keypad View– Keypad Parts List
2. After thoroughly cleaning the front edges of the A15 Elastomer Keypafront case.
3. Press the A15 Elastomer Keypad oagainst the case with no air pocket
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
A1Re
lies before beginning this disassembly:
Cable (see illustration) from the
cking tab away from the connector.t (leave the cable connected to the UI
rter Cable from the A05 UI PCB at J37. 0.312 screws (173) from the display
g harnesses (219) attached to the top . Replace any broken or frayed grounding
bly from the front case. A
(Continued on next page)
Rear View Main Assemblies
9-43
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
1 Active Display moval
Note: Remove the following assemb– Top case– Front case
To remove the A11 Active Display:1. Disconnect the W15 Active Display
A11 Active Display, as follows:– Gently pull both sides of the lo– Pull the cable out of the socke
PCB).
2. Disconnect the W17 Backlight Inve3. Remove and discard the four 4-40
assembly cover.Note: Remove the two groundintwo screws of the display assemblyharnesses.
4. Remove the display bracket assemW15
(connects to A05)11
W17
A08
47
173
219
(x4)
(x2)
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
A1Re
parts. Remove and replace any part that ged connectors.ove, disconnect the Active Display wires ht Inverter Cable at J1. Pull the backlight ket. A new display bracket is required e pre-attached.
remove, disconnect it from the A05 UI disconnected from the Active Display in
To remove, disconnect it from the A05 UI A08 Backlight Inverter (if not previously d out of the molded notches on the
oving above parts, replace if necessary. ght Inverter PCB adhesive and the Active
(used only with 3202033 - A08 Backlight old pad located on the top inside edge of
ill
Rear View Main Assemblies
9-44
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
1 Active Display moval (continued)
5. Check the condition of the followinghas cracks, broken wires, or damaA08 Backlight Inverter — To remat J2. Disconnect the W17 Backliginverter away from the display bracbecause the adhesive and foam arW15 Active Display Cable — To PCB at J36 (cable was previously step 1).W17 Backlight Inverter Cable —PCB at J37. Disconnect it from theremoved) at J1. Pull the ferrite beadisplay bracket.Display bracket (47) — After remThe display bracket has the BackliDisplay foam pre-attached.Thermal conductive pad (201) —Inverter) To remove, peel away thethe top case (see illustration 2).
W17
47
A08
Align to right edge of bracket flange
ustration 1
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
A1In parts and replace if necessary:
stration 1) illustration 3)see illustration 1)tration 1) located on the top inside edge of the top
is only required when using A08 The thermal conductive pad must be ter edge of the front case (past the ends of case)d (201), if necessary, by peeling away the dhesive, and applying the new pad to the centered between the locator notches.
o
illu
OIn
(Continued on next page)
Rear View Main Assemblies
9-45
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
1 Active Display stallation
To install the A11 Active Display:1. Verify the condition of the following
– A08 Backlight Inverter (see illu– W15 Active Display Cable (see– W17 Backlight Inverter Cable (– Display bracket (47) (see illus– Thermal conductive pad (201),
case.Note: The thermal conductive pad
Backlight Inverter - 3202033.positioned flush against the outhe locator notches in the front
2. Replace the thermal conductive paold pad, removing any remaining aupper inside edge of the top case,
bottom edge
bottom edge
201
outer edge
uter edge
stration 2
nly required with Backlight verter - 3202033
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
A1In
ter, a new display bracket (47) is required. ive and display foam piece pre-installed. ket. Place the A08 Backlight Inverter on r edge is aligned to the top side and right
r Cable “P74” connector to location J1 on
’s ferrite bead into the molded saddle s not interfere with the saddle flange. (see
the hole from the back of the display and nt side.able, unlatch “CN101” connector lock on ive Display cable under latch with metal uit board until the cable is fully seated and e connector lock to secure the cable.
A1
illu
(Continued on next page)
Rear View Main Assemblies
9-46
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
1 Active Display stallation (continued)
3. If replacing the A08 Backlight InverThe display bracket has the adhesRemove backing from display bracdisplay bracket so that J1 connectoedge of the bracket flange.
4. Connect the W17 Backlight InverteA08 Backlight Inverter.
5. Place W17 Backlight Inverter cablelocation such that the cable tie doeillustration 1).
6. Insert the snap rivet (266) throughensure the rivet expands on the fro
7. To install the W15 Active Display cA11 Active Display. Insert W15 Actcontact band facing toward the circsquare in the holding latches on th
W151
266
stration 3
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
A1In
te display backlight wires together around excess wires to the right, straight across
ide the display bracket.te the backlight wires from display along then back to the A08 Backlight Inverter.res to the A08 Backlight Inverter at J2.sembly in position in the front case. (If
ve the clear protective cover prior to
2033 must make contact with the thermal ase.
s (219) onto the top two screws (173); ding Harnesses Orientation for
(Continued on next page)
Rear View Main Assemblies
9-47
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
1 Active Display stallation (continued)
8. A11 Active Display - 3309555, roublack strain relief features. Extendthe top of the display.
9. Position the A11 Active Display ins10. A11 Active Display - 3205278, rou
the corner and under the hook and11. Connect the A11 Active Display wi12. Place the active display bracket as
replacing the Active Display, remoinstalling it into the front case.)Note: A08 Backlight Inverter - 320conductive pad (201) on the front c
13. Place the two grounding harnessetorque to 6.8 in-lb. Refer to Groungrounding harness placement.
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
A1In
s (173) to secure the display assembly to
able to the A05 UI PCB at J36 (if removed
metal contacts down) into the connector
cure the cable.e square with the connector lock.
g the front case.
grounding harnesses must be installed at vice components.
P Rear View Main Assemblies
9-48
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
1 Active Display stallation (continued)
14. Install four new 4-40 0.312 screwthe front case; torque to 6.8 in-lb.
15. Connect the W15 Active Display Cpreviously), as follows. – Open the J36 connector lock.– Insert the W15 Display Cable (
lock.– Close the connector lock to seNote: The cable connector must b
16. Complete the process by Installin
CAUTIONPossible component damage. Theprecise angles to avoid damaging de
arts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
A0PCMM
J2
2
9-49
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
8 Backlight Inverter B Diagram
IN 3202033IN 3308907 J1
J1J
3308907
Interconnect
P Back Index Next Page
LIF Replacement Procedures
F
A1DiM
CN2
9-50
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
1 Active Display agram IN 3205278
-000
W15 CN101
Interconnect
P Back Index Next Page
LIF Replacement Procedures
F
WCaM
28 AWG28 AWG28 AWG28 AWG28 AWG
P74
P74
9-51
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
17 Backlight Inverter ble Diagrams
IN 3200996
P37
P37
Interconnect
P Back Index Next Page
LIF Replacement Procedures
F
A0PC
t be removed before beginning this
from the A05 UI PCB at J31. from the A05 UI PCB at J32.0 0.312 screws (173) from the bottom the two grounding harnesses (221) r screws.ed grounding harnesses., transfer the grounding harnesses to the
(Continued on next page)
Rear View Main Assemblies
9-52
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
5 User Interface (UI) B Removal
Note: The following assemblies musdisassembly:
– Top case– Front case– Active display assembly
To remove the A05 UI PCB:1. Disconnect the W18 UI Flex Cable2. Remove the Speed Dial connector3. Remove and discard the three 4-4
edge of the A05 UI PCB. Removeattached to the left and right corneNote: Replace any broken or frayNote: If replacing the A05 UI PCBnew PCB.
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
A0PC(c
12 screw (173) from the top left corner of
from the A05 UI PCB. Remove the two he center nut.front case.
A0PC front case.
from the W04 Speed Dial Assembly, and to the lower center stud, and install the UI PCB; torque nuts to 6.8 in-lb. Refer to for grounding harness placement.
grounding harnesses must be installed at vice components.
(Continued on next page)
Rear View Main Assemblies
9-53
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
5 User Interface (UI) B Removal
ontinued)
4. Remove and discard the 4-40 0.3the A05 UI PCB.
5. Remove the three 4-40 nuts (161) grounding harnesses attached to t
6. Remove the A05 UI PCB from the
5 User Interface (UI) B Installation
To install the A05 UI PCB:1. Position the A05 UI PCB onto the
2. Insert the grounding harness (246)a second grounding harness (219)three 4-40 nuts (161) onto the A05Grounding Harness Orientation
CAUTIONPossible component damage. Theprecise angles to avoid damaging de
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
A0PC(c
s (221) onto the new lower left and right to 6.8 in-lb.s (173) onto the A05 UI PCB; torque to ess Orientation for grounding harness
ed grounding straps. the A05 UI PCB at J32. the A05 UI PCB at J31.g the active display assembly.
Rear View Main Assemblies
9-54
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
5 User Interface (UI) B Installation
ontinued)
3. Place the two grounding harnesse4-40 0.312 screws (173); torque
4. Install four new 4-40 0.312 screw6.8 in-lb. Refer to Grounding Harnplacement.Note: Replace any broken or fray
5. Install the Speed Dial connector to6. Connect the W18 UI Flex Cable to7. Complete the process by Installin
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
A0DiM(RM(n
35
6
7
J32 J34
J38 Pins 14 and 16
J33
9-55
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
5 User Interface PCB agramIN 3317230-002 oHS) orIN 3201966-007on-RoHS)
J
J3
J3J31
Interconnect
P Back Index Next Page
LIF Replacement Procedures
F
WDiM
A1
P21
Pin C1
Pin B1
Pin A1
Folded view
Pin A3
J22J21
9-56
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
18 UI Flex Cable agrams IN 3201000
P31
Fold lines
Pin 1
J31
Interconnect
P Back Index Next Page
LIF Replacement Procedures
F
WAs
lies before beginning this disassembly:
bly:nnector from the A05 UI PCB at J32.
ve the Speed Dial knob (17).e Speed Dial axle.d Dial axle. Speed Dial Assembly out of the front
50) from the Speed Dial axle.
Rear View Main Assemblies
9-57
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
04 Speed Dial sembly Removal
Note: Remove the following assemb– Top case– Front case
To remove the W04 Speed Dial Assem1. Disconnect the W04 Speed Dial co2. Turn the front case over and remo3. Loosen and remove the nut from th4. Remove the washer from the Spee5. From inside the case, pull the W04
case.6. Remove the grounding harness (2
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
WAs
ly: onto the Speed Dial axle.04 Speed Dial Assembly into the front sembly to the notch in the front case.Dial axle.axle and torque to 10 in-lb.to the axle.mbly connector to the A05 UI PCB at J32.g the front case.
Rear View Main Assemblies
9-58
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
04 Speed Dial sembly Installation
To install the W04 Speed Dial Assemb1. Insert the grounding harness (250)2. From inside the case, install the W
case by aligning the key on the as3. Install the washer onto the Speed 4. Install the nut onto the Speed Dial 5. Press the Speed Dial knob (17) on6. Connect the W04 Speed Dial Asse7. Complete the process by Installin
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
WRe
t be removed before beginning this
: the W25 Speaker Harness Extension Speaker Harness Extension Cable s for more information. 0.312 screws (173) from the speaker the speaker mounting bracket from the
ly from the front case.
Rear View Main Assemblies
9-59
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
02 Speaker Assembly moval
Note: The following assemblies musdisassembly:
– Top case– Front case
To remove the W02 Speaker Assembly1. Disconnect the speaker cable from
Cable connector. Refer to the W25removal and installation instruction
2. Remove and discard the two 4-40 mounting bracket (41), and removefront case.
3. Remove the W02 Speaker Assemb
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
WIn the front case and position the cable at
et (41) over the foam spacer and install ); torque to 6.8 in-lb.
25 Speaker Harness Extension Cable
g the front case.
Rear View Main Assemblies
9-60
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
02 Speaker Assembly stallation
To install the W02 Speaker Assembly:1. Fit the W02 Speaker Assembly into
the 2:00 position.2. Place the speaker mounting brack
two new 4-40 0.312 screws (1733. Connect the speaker cable to the W
connector. 4. Complete the process by InstallinW25
41
Parts List Interconnect Front Case View
P Back Index Next Page
LIF Replacement Procedures
F
WAsM
J32
9-61
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
04 Speed Dial sembly Diagrams
IN 3201145
P32
Interconnect
P Back Index Next Page
LIF Replacement Procedures
F
WanHaCa
t case)
ker Harness Extension Cable (bottom case)86-000 (RoHS) or 3201593-003 (non-RoHS)
1
6
P05
J05
9-62
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ront Case (continued)
02 Speaker Assembly d W25 Speaker rness Extension ble Diagrams
W02 Speaker Assembly (fronMIN 3319086-001 (RoHS) or3201593-004 (non-RoHS)
W25 SpeaMIN 33190
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
As
BoBoA1ReA1InOEOEA0ReA0In
139
135
265
A01
2
29 (x5)
221(from Power Module)
278
W03 (from Bottom Case)
173(x2)
344
9-63
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack
sembly Diagram
Interconnect
ardstack Removalardstack Installation0 SpO2 Module moval0 SpO2 Module
stallationM/PP PCB RemovalM/PP PCB Installation1 System PCB moval1 System PCB
stallation
127
149 (x3)
A06
A10
161
A0
1
252 (x4)
252
173 (x5)
125
255
(x6)
258255262
255(x2)
W05 (from Bottom Case)
P Back Index Next Page
LIF Replacement Procedures
B
A0AsWMI32WMI32
A0■
A0In
A04
No longer
185 (x5)
161 (x3)
123 (x5)
145 (x3)
in assembly
9-64
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
4 Therapy PCB sembly Diagramith Pacing:N 3317228-000 (RoHS) or 02259-010 (non-RoHS)ithout Pacing:N 3317228-001 (RoHS) or 02259-011 (non-RoHS)
4 Therapy PCB RemovalInductive Resistor
4 Therapy PCB stallation
139
147-
135 Ref
W07
229
A14
173
used
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
P
(Continued on next page)
P Therapy View Main Assemblies
Ite NoteA0 B Part of kit MIN 3202718-044
3202718-047A0 B Part of kit MIN 3202718-029
(Non-RoHS)A0 B Part of kit MIN 3202718-038
(RoHS)A0 B Part of kit MIN 3202718-020
(non-RoHS)A0 cing) Part of kit MIN 3202718-035
(RoHS)A0 cing) Part of kit MIN 3202718-016
(non-RoHS)A0 t pacing) Part of kit MIN 3202718-036
(RoHS)
9-65
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
arts List
arts 123–173 Parts 185–344 System View
m Quantity MIN CAT. Part Description1 1 3317227-002 see note System Controller PC
1 1 3201964-015 see note System Controller PC
2 1 3317226-000 see note Patient Parameter PC
2 1 3202680-002 see note Patient Parameter PC
4 1 3317228-000 (P)
see note Therapy PCB (with pa
4 1 3202259-010 (P)
see note Therapy PCB (with pa
4 1 3317228-001 (w/o P)
see note Therapy PCB (withou
P Back Index Next Page
LIF Replacement Procedures
B
Pa
(Continued on next page)
Pa Therapy View Main Assemblies
Ite NoteA0 pacing) Part of kit MIN 3202718-017
(non-RoHS)A0 pO2 Part of kit MIN 3202718-037
(RoHS)A0 pO2 Part of kit MIN 3202718-019
(non-RoHS)A1 Part of kit MIN 3202718-041
A1 Part of kit MIN 3202718-030
A1 NC Flash For devices with Masimo-Nellcor compatibility, Order kit MIN 3202718-031)
9-66
)
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
rts List (continued)
rts A01–W07 Parts 185–344 System View
m Quantity MIN CAT. Part Description4 1 3202259-011
(w/o P)see note Therapy PCB (without
6 1 3317224-000 (RoHS)
see note OEM Interface PCB (Smodels only)
6 1 3201950-004(non-RoHS)
see note OEM Interface PCB (Smodels only)
0 1 3318279 (RoHS)
see note SpO2 Module
0 1 3308709 (non-RoHS)
see note SpO2 Module
0 1 3318279 (RoHS)
see note SpO2 Module, with M
P Back Index Next Page
LIF Replacement Procedures
B
Pa
(Continued on next page)
Ite NoteA1 NC For devices with Masimo-
Nellcor compatibility, Order kit MIN 3202718-031)
A1 ssemblyW Cable121212 Part of kit MIN 3202718-02112 hex, Part of kit MIN 3202718-021
13 r Part of kit MIN 3202718-040 (RoHS)
13 r Part of kit MIN 3202718-029 (non-RoHS)
9-67
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
rts List (continued)
m Quantity MIN CAT. Part Description0 1 3308709 (non-
RoHS)see note SpO2 Module, with M
Flash
4 1 3202773-000 21300-005068 Inductive Resistor A07 1 3202383-001 21300-004307 Capacitor Discharge3 5 3201374-010 21300-004242 ISO mount, Therapy5 1 202253-772 21300-006430 Screw 4-40 1.000L7 1 3200927-006 21300-004236 Boardstack shield9 5 3201375-006 21300-004815 Standoff-M/M 0.250
0.3755 1 3201007-002 21300-004704 Boardstack connecto
5 1 3201007-002 21300-004704 Boardstack connecto
P Back Index Next Page
LIF Replacement Procedures
B
Pa
(Continued on next page)
It Note1 t
1 hex,
1 e pad No longer used in assembly
1 Part of kit MIN 3202718-0211 0
1 x 0.312L
1 x 0.500L
2
2 S, 4-40
2 0 x 0.312 3/32 hex drive
9-68
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
rts List (continued)
em Quantity MIN CAT. Part Description39 1 3200639 21300-004228 PCB support bracke
45 3 3201375-005 21300-004816 Standoff-M/M 0.250 0.250L
47 0 3201111-000 see note Thermally conductiv
49 3 3201374-011 21300-004243 ISO mount, OEM
61 9 200805-000 21300-000584 Locking hex nut, 4-4
73 3 202253-761 21300-001038 Machine screw, 4-40
85 5 202253-764 21300-004599 Machine screw, 4-40
29 2 200536-001 21300-000499 Cable tie retainer
52 5 201874-002 21300-008019 Machine screw, SEMx 5/16 L, Split
55 2 3202489-031 21300-005120 Screw-Cap, Hex,4-4Nylon
Pre Back Index Next Page
LIF Replacement Procedures
Bo
Par
Ite Note25 er Part of kit MIN 3202718-02126 Part of kit MIN 3202718-02126 12D
26 Part of kit MIN 3202718-040 (RoHS)
26 Part of kit MIN 3202718-029 (non-RoHS)
27 tack Part of kit MIN 3202718-021
34
Part Therapy View Main Assemblies
9-69
vious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ardstack (continued)
ts List (continued)
m Quantity MIN CAT. Part Description8 1 3201374-012 21300-005187 ISO mount, Paramet
2 1 3203897-000 21300-006038 Nomex shield
4 2 200804-102 21300-000580 Washer, 0.125ID, 0.3
5 1 3201374-009 21300-005578 ISO mount, System Controller (standoff)
5 1 3201374-009 21300-005578 ISO mount, System Controller (standoff)
8 1 3206405-000 21300-006593 Shield - EMI, PCB S
4 1 202305-000 21300-001052 Coin cell battery, 3 V
s A01–W07 Parts 185–344 System View
P Back Index Next Page
LIF Replacement Procedures
B
BoDi
ly.only if it is being replaced).
B.
herapy View Main Assemblies
9-70
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
ardstack sassembly
To disassemble the boardstack:1. Remove the A07 Battery.2. Remove the top case.3. Remove the front case.4. Remove the boardstack assemb5. Remove the A10 SpO2 Module (6. Remove the A06 OEM/A02 PP PC7. Remove the A01 System PCB.8. Remove the A04 Therapy PCB.
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
BoRe
plastic isolation mounts are cracking, then IN 3202718-021 as part of the
. emoved.
stall new labels.PIP.
herapy View Main Assemblies
9-71
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
ardstack assembly
Note: If there are indications that the use the boardstack repair kit Mreassembly process.
To reassemble the boardstack:1. Install the A04 Therapy PCB.2. Install the A01 System PCB.3. Install the A06 OEM/A02 PP PCB4. Install the A10 SpO2 Module, if r5. Install the boardstack assembly.6. Install the front case.7. Install the top case.8. Install the A07 Battery.9. Review the labels parts list and in10. Complete the LIFEPAK 20 Device
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
Bo
lies before beginning this disassembly:
erapy connectors are in view, and then set
(219) that connects the power module to removing the screw.ess if broken or frayed.nnector is in view.herapy Cable connector from the A04
assembly instructions to avoid a shock or
(Continued on next page)
erapy View Main Assemblies
9-72
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
ardstack Removal .
Note: Remove the following assemb– Top case– Front case
To remove the boardstack assembly:1. Turn the device so the ECG and th
the device on its left side.2. Disconnect the grounding harness
the PCB support bracket (139) by Note: Replace the grounding harn
3. Turn the device so the ac power co4. Disconnect the 4-pin W10 Power/T
Therapy PCB at J17.
WARNINGSHOCK HAZARD. Carefully follow disdamage to wires during disassembly.
Parts Lists Interconnect System View Th
P Back Index Next Page
LIF Replacement Procedures
B
Bo(c
f its track and tilt it forward to make the
rom the A04 Therapy PCB at J16 by
ector Assembly from the A04 Therapy
charge Cable from the A04 Therapy PCB
cable at J13.nd therapy connectors are in view.e from the A01 System PCB at J8 by 3/32 allen driver.
(Continued on next page)
erapy View Main Assemblies
9-73
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
ardstack Removal ontinued)
5. Lift the boardstack assembly out olower connections accessible.
6. Disconnect the W09 26-pin cable freleasing the outer tabs.
7. Disconnect the W01 Therapy ConnPCB at J14.
8. Disconnect the W07 Capacitor Disat J2.
9. Disconnect the therapy connector 10. Turn the device so that the ECG a11. Disconnect the W03 IrDA flex cabl
removing the screw (255) using a
Parts Lists Interconnect System View Th
P Back Index Next Page
LIF Replacement Procedures
B
Bo(c
ble from the A06 OEM/SpO2 Assembly at 5) using a 3/32 allen driver.ness from the A02 PP PCB at J23.ess Extension Cable from the
from the bottom case.stor’s cable from the A04 Therapy PCB
0.312 screws (173) that connect the A14 d (274) and PCB support bracket (139). from the bottom case.
OEM/SpO2 flex cable is secured to the locking post simultaneously to avoid
herapy View Main Assemblies
9-74
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
ardstack Removal ontinued)
12. Disconnect the W05 SpO2 Flex CaJ54 by first removing the screw (25
13. Disconnect the W06 ECG wire har14. Disconnect the W25 Speaker Harn
A01 System PCB at J5.15. Lift the boardstack assembly away16. Disconnect the A14 Inductive Resi
at J1.17. Remove and discard the two 4-40
Inductive Resistor to the EMI shiel18. Remove the boardstack assembly
CAUTIONPossible component damage. Thelocking posts. Remove the plug and damage to the connector.
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
Boconnector is visible, and lower the The boardstack assembly will not seat in ires do not slide into the notch cut for
the inductive resistor bracket (141).t (141) onto the PCB support bracket screws (173); torque to 6.8 in-lb. The h the top hole of the EMI shield (274).r’s cable to the A04 Therapy PCB at J1. erapy Cable as shown on the next page.Discharge Cable to the inductive resistor
r’s cable to the A04 Therapy PCB at J2.e Cable with the A14 Inductive Resistor’s ges.
(Continued on next page)
herapy View Main Assemblies
9-75
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
ardstack Installation To install the boardstack assembly:1. Turn the device so that the power
boardstack assembly into its track.the tracks correctly if the therapy wthem in the boardstack assembly.
2. Place the A14 Inductive Resistor in3. Install the inductive resistor bracke
(139) using two new 4-40 0.312 bottom bracket screw goes throug
4. Connect the A14 Inductive ResistoRoute the cable under the W01 Th
5. Tie wrap (229) the W07 Capacitor bracket (141).
6. Connect the A13 Energy Capacito7. Route the W07 Capacitor Discharg
cable as shown on the following pa
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
BBo(c
or to the A04 Therapy PCB at J13. Route rapy connector cable into the lower left
or cable has a fourth ferrite bead, 0474-008 (non-RoHS)), route this bead necting to J13
(Continued on next page)herapy View Main Assemblies
9-76
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
ardstack Installation ontinued)
8. Connect the 5-pin therapy connectthree ferrite beads of the 5-pin thecorner of the A04 therapy PCB.Note: If the 5-pin therapy connect(MIN 3200474-009 (RoHS) or 320above the battery well, prior to con
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
Bo(c
ctor to the A04 Therapy PCB at J14.ble to the A04 Therapy PCB at J16.
the bottom case.y Connector Assembly slides into the slot
(Continued on next page)
herapy View Main Assemblies
9-77
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
ardstack Installation ontinued)
.
9. Connect the 10-pin therapy conne10. Connect the W09 26-Pin Power Ca11. Seat the boardstack assembly into
Note: Ensure that the W01 Therapin the A04 Therapy PCB.
Capacitor discharge cable passes under the W01 Therapy Cable and wraps around the J13 connector.Position the therapy cable ferrites so that they will not damage the J13 connector
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
Bo(c
rapy Cable connector to the A04 Therapy
nd therapy connectors are in view.s Extension Cable to the A01 System
PP PCB at J23.cluded) to the OEM PCB at J54, fasten
en driver, and torque to 6.5 in-lb.d IrDA connectors to the sockets, and e sockets using steady pressure to avoid
to the A01 System PCB at J08, fasten en driver, and torque to 6.5 in-lb.) from the power module to the EMI shield ing new 4-40 0.312 screws (173);
g the front case.
(Continued on next page)
herapy View Main Assemblies
9-78
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
ardstack Installation ontinued)
12. Connect the 4-pin W10 Power/ThePCB at J17.
13. Turn the device so that the ECG a14. Connect the W25 Speaker Harnes
PCB at J5.15. Connect the ECG cable to the A0216. Connect the W05 SpO2 Cable (if in
with a screw (255) using a 3/32 allNote: Carefully align the SpO2 angently press the connectors into thdamage to the connector pins.
17. Connect the W03 IrDA Flex Cablewith a screw (255) using a 3/32 all
18. Install the grounding harness (219(274) and support bracket (139) ustorque to 6.8 in-lb.
19. Complete the process by Installin
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
WDiRe
s part of the capacitor replacement kit. Removal procedure to remove the cable.Installation procedure to install the
herapy View Main Assemblies
9-79
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
07 Capacitor scharge Cable placement
The W07 Capacitor Discharge Cable iComplete the A13 Energy Capacitor Complete the A13 Energy Capacitor cable.
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
A1DiM
9-80
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
4 Inductive Resistor agram IN 3202773
J01
P01
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
WDiDiM into pin 5 of P02
9-81
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
07 Capacitor scharge Cable agram IN 3202383
Capacitor Discharge Connector (tie-wrapped to Inductive Resistor)
Interconnect
P Back Index Next Page
LIF Replacement Procedures
BA1Re
lies before beginning this disassembly:
al removal)
y removing the two nuts (161) and
0.312 screws (252) from the A10 SpO2
m the boardstack assembly.
A1In placement kit for the LIFEPAK 20 device.
position over the A06 OEM PCB.s (252) into the A10 SpO2 Module; torque
ecuring it to the A06 OEM PCB with the torque to 6.8 in-lb.g the front case.
herapy View Main Assemblies
9-82
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
0 SpO2 Module moval
Note: Remove the following assemb– Top case– Front case– Boardstack assembly (option
To remove the SpO2 Module:1. Remove the Nomex shield (262) b
washers (264).2. Remove and discard the four 4-40
Module.3. Lift the A10 SpO2 Module away fro
0 SpO2 Module stallation
To Install the A10 SpO2 Module: Note: Order correct SpO2 module re1. Position the A10 SpO2 Module into2. Install four new 4-40 0.312 screw
to 6.8 in-lb.3. Install the Nomex shield (262) by s
two washers (264) and nuts (161);4. Complete the process by Installin
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
A1Di
M
J03 to J52
9-83
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
0 SpO2 Module agram
IN 3206274
J01 to J53
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
A0anAs
lies before beginning this disassembly:
l removal)and optional A06 OEM/SpO2 assemblies:ble from the A06 OEM/SpO2 Assembly at
ness from the A02 PP PCB at J23.937 screw (125). Remove the three 4-40 rameter PCB.06 OEM/SpO2 option, remove the Nomex ashers (264) and nuts (161).odule if replacing the A06 OEM PCB.B (OEM/SpO2) assembly away from the the PCB clears the lip on the frame in the
(Continued on next page)
herapy View Main Assemblies
9-84
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
2 Patient Parameter d A06 OEM/SpO2 sembly Removal
Note: Remove the following assemb– Top case– Front case– Boardstack assembly (optiona
To remove the A02 Patient Parameter 1. Disconnect the W05 SpO2 Flex Ca
J54 by removing the screw (255).2. Disconnect the W06 ECG wire har3. Remove and discard the 4-40 0.
nuts (161) from the A02 Patient Pa4. If the device is equipped with the A
shield (262) by removing the two wNote: Remove the A10 SpO2 m
5. Lift the A02 Patient Parameter PCboardstack assembly. Ensure that lower right corner.
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
A0anAs(c
mount (258) installed in the A02 Patient is in good condition.06 OEM/SpO2 option:ISO mounts (149) installed in the A06 re in good condition.meter PCB from the A06 OEM/SpO2
rameter PCB or A06 OEM PCB, remove ld PCBs, note the condition, and install ce the isolated mounts if broken or
herapy View Main Assemblies
9-85
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
2 Patient Parameter d A06 OEM/SpO2 sembly Removal
ontinued)
6. Inspect the orange parameter ISOParameter PCB. Verify the mount
7. If the device is equipped with the Aa. Inspect the three, white, OEM
OEM PCB. Verify the mounts ab. Separate the A02 Patient Para
assembly at J24.Note: If replacing the A02 Patient Pa
the isolated mounts from the othem on the new PCBs. Replacracked.
258
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
A0anAs
nd optional A06 OEM/SpO2 assembly:SO mount (258) is installed on the A02 uare end facing out.06 OEM/SpO2 option:M ISO mounts (149) are installed on the ends facing out.eter to the A06 OEM/SpO2 assembly at
OEM/SpO2) PCB onto the five standoffs sure the standoffs are tight and in good rs the lip in the lower right corner and the
06 OEM/SpO2 option:, if previously removed.
(Continued on next page)
herapy View Main Assemblies
9-86
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
2 Patient Parameter d A06 OEM/SpO2 sembly Installation
To install the A02 Patient Parameter a1. Make sure the orange parameter I
Patient Parameter PCB with the sq2. If the device is equipped with the A
a. Make sure the three, white, OEA06 OEM PCB with the square
b. Connect the A02 Patient ParamJ24.
3. Install the A02 Patient Parameter ((129) on the boardstack shield (encondition). Make sure the PCB clea60-pin connector seats correctly.
4. If the device is equipped with the Aa. Install the A10 SpO2 module
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
A0anAs(c
onto the OEM PCB by securing it with two torque to 6.8 in-lb. Make sure the fold on er left corner of the OEM PCB.61) and new 4-40 0.312 screw (252) .8 in-lb.
the A06 OEM/SpO2 option, make sure ith two nuts (161) along the left side only;
ts (161) and new 4-40 1.00 screw (125) B; torque to 6.8 in-lb.cluded) to the OEM PCB at J54 and
nnector to the sockets, and gently press ing steady pressure to avoid damage to
PP PCB at J23.g the front case.
erapy View Main Assemblies
9-87
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
2 Patient Parameter d A06 OEM/SpO2 sembly Installation
ontinued)
b. Install the Nomex shield (262) washers (264) and nuts (161);the Nomex shield is in the upp
c. Install the one remaining nut (1onto the OEM PCB; torque to 6
5. If the device is NOT equipped withthe boardstack shield is secured wtorque to 6.8 in-lb.
6. Install the three remaining 4-40 nuonto the A02 Patient Parameter PC
7. Connect the W05 SpO2 Cable (if infasten with a screw (255).Note: Carefully align the SpO2 cothe connectors into the sockets usconnector pins.
8. Connect the ECG cable to the A029. Complete the process by Installin
Parts Lists Interconnect System View Th
P Back Index Next Page
LIF Replacement Procedures
B
A0PCM(R32(n
J21
J22
9-88
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
2 Patient Parameter B Diagram
IN 3317226-000 oHS) or 02680-002 on-RoHS)
J24
J23
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
A0PCM(R32(n
J54
P24
9-89
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
6 OEM Interface B Diagram
IN 3317224-000 oHS) or 01950-004 on-RoHS)
J52
J53
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
CoRe lies before beginning this disassembly:
al removal)OEM/SpO2 assembly, if applicable)
eld (127).er is installed on the A01 System tive contacts visible on top of the battery) the side of the battery)
9-90
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
in Cell Battery placement Note: Remove the following assemb
– Top case– Front case– Boardstack assembly (option– A02 Patient Parameter PCB (
To replace the coin battery:1. Remove the patient parameter shi2. Identify which type of coin cell hold
Controller PCB: A) Keystone (posior B) Renata (positive contacts to
P Back Index Next Page
LIF Replacement Procedures
.B
cordance with Replacement Procedure ment Procedure B for Renata holder.
B) Renata holder (positive contacts are to the side of the coin cell battery)
le
9-91
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
3. Replace the coin cell battery in acA for Keystone holder, or Replace
A) Keystone holder (positive contacts visibon top of the coin cell battery)
P Back Index Next Page
LIF Replacement Procedures
B
e: of the Keystone coin cell battery holder nd or deform the positive contacts during ry holder is damaged, replacement of the
required.itive side of battery holder while using a f the battery closest to the negative side contacts) until the battery releases from
9-92
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
Replacement Procedure A - KeystonCaution: The positive contactsare easily damaged. Do not beremoval or insertion. If the batteA01 System Controller PCB is
1. Push battery gently toward the posflat screwdriver to lift up the edge oof the holder (opposite the positivethe holder.
P Back Index Next Page
LIF Replacement Procedures
B
4) by inserting battery (positive up) nd then pressing it into the negative side attery is fullyseated in the holder.
d, check the voltage on the coin cell eter to confirm that the battery is installed h the holder.
r PCB and A06 OEM PCB.
9-93
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
2. Install the new coin cell battery (34underneath the positive contacts aof battery holder. Ensure that the b
3. After the battery has been replacebattery holder circuit with a multi-mcorrectly and is making contact wit
4. Replace the PCB shield (127).5. Install the A02 Patient Paramete
P Back Index Next Page
LIF Replacement Procedures
B
reviously removed).g the front case.
erapy View Main Assemblies
9-94
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
6. Install the A10 SpO2 Module (if p7. Complete the process by Installin
Parts Lists Interconnect System View Th
P Back Index Next Page
LIF Replacement Procedures
B
sitive side of battery holder while using a f the battery closest to the negative side
ses from the holder.
9-95
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
Replacement Procedure B - Renata:1. Push battery gently towards the po
flat screwdriver to lift up the edge oof the holder until the battery relea
P Back Index Next Page
LIF Replacement Procedures
B
4) by inserting the side of the battery ontacts and then pressing it into the Ensure that the battery is fully seated in battery touches the positive contacts
d, check the voltage on the coin cell eter to confirm that the battery is installed h the holder.
r PCB and A06 OEM PCB.
9-96
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
2. Install the new coin cell battery (34(positive up) against the positive cnegative side of the battery holder.the holder and that the side of the
3. After the battery has been replacebattery holder circuit with a multi-mcorrectly and is making contact wit
4. Replace the PCB shield (127).5. Install the A02 Patient Paramete
P Back Index Next Page
LIF Replacement Procedures
B
reviously removed).g the front case.
erapy View Main Assemblies
9-97
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
6. Install the A10 SpO2 Module (if p7. Complete the process by Installin
Parts Lists Interconnect System View Th
P Back Index Next Page
LIF Replacement Procedures
B
A0Re
lies before beginning this disassembly:
and A06 OEM/SpO2 assembly, if
ded standoffs (129) from the A01 System
ff (265) from the A01 System PCB. the PCB support bracket (139).
135) (connects the A01 System PCB J03 , and safeguard it for reuse.ay remain connected to the A04 Therapy
may fall out completely when the ure to account for it immediately.
erapy View Main Assemblies
9-98
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
1 System PCB moval
Note: Remove the following assemb– Top case– Front case– Boardstack assembly– A02 Patient Parameter PCB (
applicable)To remove the A01 System PCB:1. Remove the PCB shield (127).2. Remove and discard the five threa
PCB.3. Remove the round, snap-in stando4. Remove the A01 System PCB from5. Locate the 8-pin stack connector (
with the A04 Therapy PCB at J15)Note: The 8-pin stack connector mPCB or the A01 System PCB, or itA01 System PCB is removed. Be s
139
129 149(x5)
Parts Lists Interconnect System View Th
P Back Index Next Page
LIF Replacement Procedures
B
A0In PCB, ensure that the plastic standoff
end up, on the A01 System PCB.35) into the A04 Therapy PCB at J15.PCB over the PCB support bracket (139), et standoffs. As the A01 System PCB rt bracket standoffs and the pins on the seat with their connectors evenly. (129), long end up, into the support
insulated standoff in the lower right
d.ing it down the five threaded standoffs on
(Continued on next page)
erapy View Main Assemblies
9-99
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
1 System PCB stallation
To install the A01 System PCB:1. If you are replacing the A01 System
(149) is correctly positioned, large 2. Insert the 8-pin stack connector (13. Carefully position the A01 System
and slide it down the support brackslides down, ensure that the suppo8-pin and 60-pin stack connectors
4. Install five new threaded standoffsbracket.Note: Do not install a screw in thecorner at this time.
5. Replace the coin battery if neede6. Install the PCB shield (127) by slid
the A01 System PCB.
139
129 149(x5)
Parts Lists Interconnect System View Th
P Back Index Next Page
LIF Replacement Procedures
B
A0In
r PCB and A06 OEM PCB assembly.reviously removed)..g the front case.
erapy View Main Assemblies
9-100
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
1 System PCB stallation (continued)
7. Install the A02 Patient Paramete8. Install the A10 SpO2 Module (if p9. Install the Boardstack Assembly10. Complete the process by Installin
Parts Lists Interconnect System View Th
P Back Index Next Page
LIF Replacement Procedures
B
A0DiM(R32(n
4
J03
J02
J01
9-101
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
1 System PCB agram IN 3317227-002 oHS) or 01964-015 on-RoHS)
Coin battery
J02
J08 J05 J0
J07
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
A0Re
lies before beginning this disassembly:
0.312 screws (173) connecting the o the PCB support bracket (139). mbly (A14). 0.500 screws (185) located inside the
n with the A04 Therapy PCB.from the metal standoffs along the top illustration B at left).
m the PCB support bracket (139).135) (connecting the A01 System PCB at 5) and safeguard it for reuse.
(Continued on next page)
herapy View Main Assemblies
9-102
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
4 Therapy PCB moval
Note: Remove the following assemb– Top case– Front case– Boardstack assembly
To remove the A04 Therapy PCB:1. Remove and discard the two 4-40
inductive resistor assembly (A14) t2. Remove the inductive resistor asse3. Remove and discard the five 4-40
five insulated standoffs. Note: The standoffs should remai
4. Remove the three 4-40 nuts (161) edge of the A04 Therapy PCB (see
5. Remove the A04 Therapy PCB fro6. Locate the 8-pin stack connector (
J3 with the A04 Therapy PCB at J1
A
B
173
A14
139
161
185
A04
(x5)
(x3)
278
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
A0Re
ay remain connected to the A04 Therapy may fall out completely when the ure to account for it immediately. PCB, remove the five insulated standoffs
ote the condition, and reinstall them, large CB.
A0In rt bracket (139), install three new
nto the bracket.CB, ensure that the five plastic standoffs e end up, on the PCB.stalled on the boardstack assembly, tor (135) and the 60-pin stack connector System PCB.
(Continued on next page)
erapy View Main Assemblies
9-103
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
4 Therapy PCB moval (continued)
Note: The 8-pin stack connector mPCB or the A01 System PCB, or itA01 System PCB is removed. Be sNote: If replacing the A04 Therapy(149) from the old Therapy PCB, nend up, on the new A04 Therapy P
4 Therapy PCB stallation
To install the A04 Therapy PCB:1. If you are replacing the PCB suppo
standoffs (145), short side down, o2. If you are replacing the Therapy P
(149) are correctly positioned, largNote: If the A01 System PCB is inensure that the 8-pin stack connecare securely positioned on the A01
Parts Lists Interconnect System View Th
P Back Index Next Page
LIF Replacement Procedures
B
A0In
B with the PCB support bracket (139) 04 Therapy PCB slides down the support pins on the 8-pin and 60-pin stack ors evenly.s (185) in the five insulated standoffs
to the metal standoffs along the top edge 6.8 in-lb.bly (A14) onto the PCB support bracket screws (173); torque to 6.8 in-lb. The gh the top hole of the EMI shield (278). cable under the W01 Therapy Cable, the ischarge Cable (see illustration)..g the front case.
herapy View Main Assemblies
9-104
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
4 Therapy PCB stallation (continued)
3. Carefully align the A04 Therapy PCand press it into position. As the Abracket standoffs, ensure that the connectors seat with their connect
4. Install five new 4-40 0.500 screw(149); torque to 6.8 in-lb.
5. Install the three 4-40 nuts (161) onof the A04 Therapy PCB; torque to
6. Install the inductive resistor assem(139) using two new 4-40 0.312 bottom bracket screw will go throu
7. Route the A14 Inductive Resistor’ssame way as the W07 Capacitor D
8. Install the Boardstack Assembly9. Complete the process by Installin
Parts Lists Interconnect System View T
P Back Index Next Page
LIF Replacement Procedures
B
A0DiM(R32(n
(Continued on next page)
J01
J02
J17
Therapy Pacer Simm PCB
9-105
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
oardstack (continued)
4 Therapy PCB agram (With Pacing)IN 3317228-000 oHS) or 02259-010 on-RoHS)
J15
J13
J14J16
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
As(M
Part Connectors View Main Assemblies
BoBoA1A1■
■
■
■
A0A0A1ReA1In
105 (x4)
f
A13(x2)
162
23895 (x2)
173 (x10)
(A)12225
W09
99A03
89
tail B
221
A07103
227
159
22 (part of kit320718-024)(x2)
9-106
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case
sembly Diagram odules)
s A03–W09 Parts W10–95 Parts 99–183 Parts 221–270
ttom Case Disassemblyttom Case Reassembly2 Printer Module Removal2 Printer Module InstallationPrinterPrinter flex cablePrinter bezelPrinter shroud
3 Power Module Removal3 Power Module Installation3 Energy Capacitor moval3 Energy Capacitor
stallationBottom View
Detail B
241 Center Between Terminals
241 Re
93
W14
A12
See De
83
12 (E)
A07 Connection
12(F) SpO2
183 270LIFEPAK 20e
device Only
LIFEPAK 20e Only
W13
W08
W10
P Back Index Next Page
LIF Replacement Procedures
B
As(C
Pa Module View Main Assemblies
159
W01
W25
A0WWInWWWWWW
Ref
268
9-107
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
sembly Diagram onnectors)
rts A03–W09 Parts W10–95 Parts 99–183 Parts 221–270
W06
113
W03
111
173 (x2)
W05 (x2)229
7 Battery Replacement01 Therapy Connector Removal01 Therapy Connector stallation06 ECG Connector Removal06 ECG Connector Installation05 SpO2 Connector Removal05 SpO2 Connector Installation03 IrDA Assembly Removal03 IrDA Assembly Installation
SpO2 Only
P Back Index Next Page
LIF Replacement Procedures
B
Pa
(Continued on next page)
P Connectors View Main Assemblies
Ite Note
A K 20 Part of kit MIN 3202718-010
A K 20e Part of kit MIN 3202718-039 (RoHS)
A K 20e Part of kit MIN 3202718-022 (non-RoHS)
A , LIFEPAK 20
A AK 20e
A nthead
A nthead
A Part of kit MIN 3202718-025
W ly Part of kit MIN 3202718-043 (RoHS)
9-108
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
rts List
arts W10–95 Parts 99–183 Parts 221–270 Module View
m Quantity MIN CAT. Part Description
03 1 3202131-010 see note Power Module Assy, LIFEPA
03 1 3317740-000 (RoHS)
see note Power Module Assy, LIFEPA
03 1 3202131-009 (non-RoHS)
see note Power Module Assy, LIFEPA
07 1 3200497-001 11141-000068 12V, 3Ah, NiMH battery pack
07 1 3205296 11141-000112 Battery Pack – Li-ion, LIFEP
12 1 3318747-000 (RoHS)
21240-000003 Printer - 50MM, Thermal Pri
12 1 3200920-000(non-RoHS)
21240-000001 Printer - 50MM, Thermal Pri
13 1 3200846 see note Energy Storage Capacitor
01 1 3200474-009 (RoHS)
see note Therapy Connector Assemb
P Back Index Next Page
LIF Replacement Procedures
B
PaIte Note
W ly Part of kit MIN 3202718-026 (non-RoHS)
W
W
W Part of kit MIN 3202718-013
W
W
W Part of kit MIN 3202718-039 (RoHS)
W Part of kit MIN 3202718-022 (non-RoHS)
9-109
(Continued on next page)
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
rts List (continued)m Quantity MIN CAT. Part Description
01 1 3200474-008 (non-RoHS)
see note Therapy Connector Assemb
03 1 3200926-007 (RoHS)
21300-008131 IrDA Flex Assembly
03 1 3200926-006(non-RoHS)
21300-004235 IrDA Flex Assembly
05 1 3200925-006 21300-004234 SpO2 Flex Assembly
06 1 3318315 (RoHS)
21330-001521 ECG 7-Contact Receptacle
06 1 3201010-009 (non-RoHS)
21300-004239 ECG 7-Contact Receptacle
08 1 3206579-001 21330-001166 Battery Cable, LIFEPAK 20e
08 1 3206579-001 21330-001166 Battery Cable, LIFEPAK 20e
P Back Index Next Page
LIF Replacement Procedures
B
Pa
(Continued on next page)
Par Connectors View Main Assemblies
Ite Note
W ble
W PAK 20e Part of kit MIN 3202718-039 (RoHS)
W PAK 20e Part of kit MIN 3202718-022 (non-RoHS)
W Part of kit MIN 3202718-039 (RoHS)
W Part of kit MIN 3202718-022 (non-RoHS)
W 20e Part of kit MIN 3202718-039 (RoHS)
W 20e Part of kit MIN 3202718-022 (non-RoHS)
W y
9-110
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
rts List (continued)
ts A03–W09 Parts 99–183 Parts 221–270 Module View
m Quantity MIN CAT. Part Description
09 1 3201241-000 21300-004669 Power to Therapy 26-pin Ca
10 1 3206857-000 21330-001165 Power/Therapy Cable, LIFE
10 1 3206857-000 21330-001165 Power/Therapy Cable, LIFE
11 1 3201997 see note ECG Sync/System Cables
11 1 3201997 see note ECG Sync/System Cables
13 1 3206469-003 21330-001164 AC Power Cable, LIFEPAK
13 1 3206469-003 21330-001164 AC Power Cable, LIFEPAK
14 1 3201001-006 21300-008058 Printer Flex Cable Assembl
P Back Index Next Page
LIF Replacement Procedures
B
Pa
(Continued on next page)
Par Connectors View Main Assemblies
Ite Note
W Ext.
W Ext.
12 K 20 Refer to Labels Assembly
12 K 20e Refer to Labels Assembly
22 8 Part of kit MIN 3202718-024
83
89
93 ssy)
95 Part of kit MIN 3202718-024
9-111
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
rts List (continued)
ts A03–W09 Parts W10–95 Parts 221–270 Module View
m Quantity MIN CAT. Part Description
25 1 3319086-000 (RoHS)
21300-008132 Speaker Assembly Harness
25 1 3201593-003(non-RoHS)
21300-004246 Speaker Assembly Harness
sheet 3201640 see note Label Set (6 labels), LIFEPA
sheet 3206034 see note Label Set (6 labels), LIFEPA
2 3202228-562 21300-003883 Standoff-Hex, M/F,4-40,0.18
1 3201408-000 21300-004621 Printer Bezel
1 3200626-004 21300-004306 Printer Shroud
2 804447-36 21300-007458 Foam Spacer (part of A13 a
2 3200922-000 21300-004619 Capacitor Support Bracket
P Back Index Next Page
LIF Replacement Procedures
B
Pa
Par Connectors View Main Assemblies
Ite Note
99
10
10 e
10 Part of bottom case assembly
11 Part of kit MIN 3202718-043 (RoHS)
11 Part of kit MIN 3202718-026 (non-RoHS)
11 Clip Part of kit MIN 3202718-013
15
16 13 assembly) Part of kit MIN 3202718-025
17 12L
9-112
(Continued on next page)
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
rts List (continued)
ts A03–W09 Parts W10–95 Parts 99–183 Module View
m Quantity MIN CAT. Part Description
1 3201597-000 21300-004653 EMI Foam Core Gasket
3 1 3200628-002 21300-004835 Battery Door, LIFEPAK 20
3 1 3200628-004 21300-006412 Battery Door, LIFEPAK 20
5 4 802885-00 21300-002137 Mounting Foot
1 1 200040-001 21300-000149 Therapy Retaining Ring
1 1 200040-001 21300-000149 Therapy Retaining Ring
3 1 3200921-000 21300-004602 SpO2 Connector Mounting
9 1 3200625-006 21300-004889 Bottom case assembly
2 1 3009787-003 21300-004110 Capacitor shield (part of A
3 12 202253-761 21300-001038 Machine screw 4-40 0.3
P Back Index Next Page
LIF Replacement Procedures
B
Pa
Par Connectors View Main Assemblies
Ite Note
18 PAK 20 Refer to Labels Assembly
18 PAK 20e Refer to Labels Assembly
22
22
22 Attached to battery door (103)
22 Part of kit MIN 3202718-025
23 Part of kit MIN 3202718-024
24 Part of kit MIN 3202718-025
26 Mount Part of kit MIN 3202718-043 (RoHS)
26 Mount Part of kit MIN 3202718-026 (non-RoHS)
27 ning LIFEPAK 20e only
9-113
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
rts List (continued)
ts A03–W09 Parts W10–95 Parts 99–183 Module View
m Quantity MIN CAT. Part Description
3 1 3201643-012 see note Serial number label, LIFE
3 1 3201643-016 see note Serial number label, LIFE
1 1 3202246-004 21300-004255 Grounding strap harness
5 1 3202377-010 21300-004400 Plastic Fastener
7 1 802885-01 21300-002138 Mounting foot
9 2 200536-001 21300-000499 Cable tie retainer
8 1 3206900-001 21300-006962 Dielectric shield
1 1 3300694-000 21300-007794 Poron Foam, Capacitor
8 1 3203445-001 21300-005784 Seal, Therapy Connector
8 1 3203445-001 21300-005784 Seal, Therapy Connector
0 1 3206152-000 21501-001625 Label, NIMH Battery War
P Back Index Next Page
LIF Replacement Procedures
B
BoDi
ly..or.
ctor.r.or.r.ss Extension Cable.
P Connectors View Main Assemblies
9-114
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
ttom Case sassembly
To disassemble the bottom case:1. Remove the A07 Battery.2. Remove the top case.3. Remove the front case.4. Remove the boardstack assemb5. Remove the A12 Printer Module6. Remove the A13 Energy Capacit7. Remove the A03 Power Module.8. Remove the W01 Therapy Conne9. Remove the W06 ECG Connecto10. Remove the W05 SpO2 Connect11. Remove the W03 IrDA Connecto12. Remove the W25 Speaker Harne
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
BoRe cing case).
friction foot pads (105), as needed.ot (227) to the battery door (103), as
Extension Cable.
.
tor.
.
(Continued on next page)
P Connectors View Main Assemblies
9-115
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
ttom Case assembly
To reassemble the bottom case:1. Obtain a new bottom case (if repla2. Inspect and install the bottom case3. Inspect and install the mounting fo
needed.4. Install the W25 Speaker Harness5. Install the W03 IrDA Connector.6. Install the W05 SpO2 Connector7. Install the W06 ECG Connector.8. Install the W01 Therapy Connec9. Install the A03 Power Module.10. Install the A13 Energy Capacitor11. Install the A12 Printer Module.12. Install the boardstack assembly.
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
BoRe(c
stall new labels.PIP.
P Connectors View Main Assemblies
9-116
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
ttom Case assembly
ontinued)
13. Install the front case.14. Install the top case.15. Install the A07 Battery.16. Review the labels parts list and in17. Complete the LIFEPAK 20 Device
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
A1Re
embly and shroud:r Flex cable is remove, the following mbly:
the printer paper roll.cated inside the printer on the rear wall.f the printer shroud (89).able from the printer at printer
sembly instructions to avoid a shock or embly.
(Continued on next page)
P Connectors View Main Assemblies
9-117
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
2 Printer Module moval
To remove the A12 Printer Module assNote: If Printer shroud or W14 Printe
assemblies will require disasse– A07 Battery– Top case– Front case– Boardstack
1. Open the printer door and remove2. Loosen the two captured screws lo3. Carefully pull the A12 Printer out o4. Disconnect the W14 Printer Flex C
connection J1.
W14
173
89
(x3)
WARNINGSHOCK HAZARD. Carefully follow disascausing damage to wires during disass
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
A1Re
the removal process is complete. If W14 Printer Flex Cable, continue with the art is removed.
away from the bottom case.0 0.312 screws (173) from the bottom of
he 4-pin power cable. from the A03 Power Module at J45, and tout.e W14 Printer Flex Cable through the
m the bottom case.way and carefully remove the W14 Printer he cable is held in place by adhesive, so id damaging the connectors or the cable.
P Connectors View Main Assemblies
9-118
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
2 Printer Module moval (continued)
Note: If removing the A12 Printer,removing the printer shroud or the removal process until the desired p
5. Slide the printer bezel (83) up and6. Remove and discard the three 4-4
the printer shroud (89).7. Carefully lift the shroud to access t8. Disconnect the 4-pin power cable
feed it through the small shroud cu9. Feed the 4-pin power cable and th
large shroud cutout.10. Remove the printer shroud (89) fro11. Lift the W06 ECG Cable out of the
Flex Cable from the bottom case. Tit should be removed evenly to avo
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
A1In
, start at step 9.
nder the W06 ECG Cable and position the f the guide on the bottom case.nd the 4-pin power cable connector .rough the small slot in the shroud.r to the A03 Power Module at J45, tioned correctly.the bottom case.ws (173) into the bottom of the printer
(Continued on next page)
P Connectors View Main Assemblies
9-119
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
2 Printer Module stallation
Note: If installing the A12 Printer onlyTo install the printer module:1. Slide the W14 Printer Flex Cable u
printer cable along the right side o2. Insert the printer cable connector a
through the large slot in the shroud3. Insert the 4-pin power connector th4. Connect the 4-pin power connecto
ensuring that the connector is posi5. Position the printer shroud (89) in 6. Install three new 4-40 0.312 scre
shroud; torque to 6.8 in-lb.
W14
173
89
(x3)
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
A1In
) into the printer shroud to secure the J45
g that it is flush with the bottom case.le to the J1 connector on the printer. The ar of the printer.able lays between the two captured
r shroud. cated in the A12 Printer and torque to
ter and close the printer door.
PIP.
P Connectors View Main Assemblies
9-120
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
2 Printer Module stallation (continued)
7. If removed, press the fastener (225flex connector.
8. Insert the printer bezel (83) ensurin9. Connect the W14 Printer Flex Cab
cable should lay flat against the re10. Ensure that the W14 Printer Flex C
screws.11. Slide the A12 Printer into the printe12. Tighten the two captured screws lo
10 in-lb.13. Install the paper roll in the A12 Prin14. Install the boardstack.15. Install the front case.16. Install the top case.17. Install the A07 Battery.18. Complete the LIFEPAK 20 Device
83
A12
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
WDiM
Pin 2Pin 1
Pin 40Pin 39
etail B
Detail A
see Detail A
9-121
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
14 Printer Flex Cable agrams IN 3201001
Pin 2Pin 4
Pin 3
Detail C
Pin 1
fold-up lines
Adhesive tape (center on flex)
fold-up lines
see Dsee Detail C
Detail B
Interconnect
P Back Index Next Page
LIF Replacement Procedures
BA1Re
lies before beginning this disassembly:
t removed, remove and discard the screw
y Cable from the A04 Therapy PCB at
y from the printer shroud (89) and the
r Discharge Cable from the A04 Therapy
sembly instructions to avoid a shock or embly.
(Continued on next page)
P Connectors View Main Assemblies
9-122
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
3 Energy Capacitor moval
Note: Remove the following assemb– A07 Battery– Top case– Front case
To remove the A13 Energy Capacitor:1. If the boardstack assembly was no
and ground cable (221).2. Disconnect the W10 Power/Therap
J17.3. Pull the boardstack assembly awa
power module.4. Disconnect the W07/A13 Capacito
PCB at J2.
WARNINGSHOCK HAZARD. Carefully follow disascausing damage to wires during disass
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
A1Re
e adjacent hardware or wires when arge Cable.) securing the W07 Capacitor Discharge ket (141). 0.312 screws (173) from the rear of the
apacitor brackets.foam tape (162 and 93) from the
(95), remove and discard the two 4-40 f the capacitor brackets (95) and remove capacitor shield (238) (see illustration on
P Connectors View Main Assemblies
9-123
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
3 Energy Capacitor moval (continued)
Note: Take care not to damage thremoving the W07 Capacitor Disch
5. Remove the cable tie retainer (229Cable to the inductive resistor brac
6. Remove and discard the two 4-40 capacitor brackets (95).
7. Lift the capacitor (A13) out of the c8. Remove the capacitor sleeve with
capacitor.9. If removing the capacitor brackets
0.312 screws (173) from the front othe capacitor brackets (95) and thenext page).
A13
95 173(x2)
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
A1In standoffs (22) are on the power module.
d the two capacitor brackets (95) onto the 12 screws (173); torque to 6.8 in-lb (if the
ensuring that the plastic sleeve and poron ecurely.wrapped tightly around the capacitor, with acitor. Poron tape must secure the sleeve
to ensure that foam tape (240) is present
itor brackets (95) with the capacitor cable the warning label visible at the top of the
s (173) into the capacitor brackets; torque
(Continued on next page)
P Connectors View Main Assemblies
9-124
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
3 Energy Capacitor stallation
To install the A13 Energy Capacitor:1. Ensure that two capacitor bracket 2. Install the capacitor shield (238) an
standoffs using two new 4-40 0.3brackets were removed).
3. Inspect the A13 Energy Capacitor tape are positioned correctly and sNote: The plastic sleeve must be the wrap joint at the top of the capat both ends of the capacitor.
4. Inspect the A13 Energy Capacitor (optional on LIFEPAK 20 device).
5. Install the capacitor into the capacend toward the printer shroud and capacitor.
6. Install two new 4-40 0.312 screwto 6.8 in-lb.
238
95173
22
240 Center Between Terminals
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
A1In
ts are centered on the poron tape connect rapy PCB at J2. The W07 Capacitor 4 of this connector.ge Cable to the inductive resistor bracket ). Route the cable over the A04 Therapy llustration) as the inductive resistor
stalled.lled. herapy Cable connector to the A04 oardstack assembly.73) and fasten the ground cable (221) to
PIP.
P Connectors View Main Assemblies
9-125
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
3 Energy Capacitor stallation (continued)
7. Ensuring that the capacitor brackethe capacitor cable to the A04 TheDischarge Cable is attached at pin
8. Secure the W07 Capacitor Dischar(141) with a cable tie retainer (229PCB using the same routing (see icables.
9. Install the power module, if not in10. Install the boardstack, if not insta11. Reconnect the 4-pin W10 Power/T
Therapy PCB at J17. Reseat the b12. Install a new 4-40 0.312 screw (1
the boardstack; torque to 6.8 in-lb.13. Install the front case.14. Install the top case.15. Install the A07 Battery.16. Complete the LIFEPAK 20 Device
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
A0Re
lies before beginning this disassembly:
l)y:lled in the bottom case, continue with has been removed, proceed to step 5.y Cable from the A04 Therapy PCB at
from the A04 Therapy PCB at J16.
sembly instructions to avoid a shock or embly.
(Continued on next page)
P Connectors View Main Assemblies
9-126
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
3 Power Module moval
Note: Remove the following assemb– A07 Battery– Top case– Printer module– Capacitor (optional removal)– Boardstack (optional remova
To remove the power module assembl1. If the boardstack assembly is insta
step 2. If the boardstack assembly2. Disconnect the W10 Power/Therap
J17.3. Disconnect the W09 26-Pin Cable
WARNINGSHOCK HAZARD. Carefully follow disascausing damage to wires during disass
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
A0Re
y from the printer shroud and power
ove the A13 Energy Capacitor
ght 4-40 0.312 screw (173) that secures and grounding harness (221).ess (221) as you remove the right forward ess if broken or frayed.ft 4-400.312 screw (173) that secures
(173) that secures the right rear corner
le up, clearing the loosened screw, and
P Connectors View Main Assemblies
9-127
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
3 Power Module moval (continued)
4. Pull the boardstack assembly awamodule.
5. If replacing the power module, rem(complete steps 6 through 9).
6. Remove and discard the forward rithe right side of the power moduleNote: Remove the grounding harnscrew. Replace the grounding harn
7. Remove and discard the forward lethe left side of the power module.
8. Loosen the rear 4-400.312 screwof the power bracket three turns.
9. Tilt the left side of the power moduremove it from the bottom case.
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
BA0In 400.312 screw (173) is loosely installed
case.ottom case ensuring that the notch in the the loosened screw.73) in the power bracket’s left forward
rough the grounding strap (221) ring, and ket’s right forward corner; torque to 6.8 in-
the grounding strap.3) in the rear right corner; torque to 6.8 in-
, if it was removed.moved.tween the A03 Power Module at J41 and
(Continued on next page)
P Connectors View Main Assemblies
9-128
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
3 Power Module stallation
To install the power module assembly:1. Ensure that the right rear corner 4-
(back off 3 to 5 turns) in the bottom2. Position the power module in the b
rear right lip slips into place under 3. Install a new 4-400.312 screw (1
corner; torque to 6.8 in-lb.4. Insert a 4-400.312 screw (173) th
install the screw in the power braclb.Note: If broken or frayed, replace
5. Tighten the 4-400.312 screw (17lb.
6. Install the A13 Energy Capacitor7. Install the boardstack, if it was re8. Connect the W09 26-Pin Cable be
the A04 Therapy PCB at J16.
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
A0In
rapy Cable connector to the A04 Therapy
PIP.
P Connectors View Main Assemblies
9-129
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
3 Power Module stallation (continued)
9. Connect the 4-pin W10 Power/ThePCB at J17.
10. Install the A12 Printer Module.11. Install the front case.12. Install the top case.13. Install the A07 Battery.14. Complete the LIFEPAK 20 Device
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
A0DiM(R32(n
J41J48
9-130
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
3 Power Module agramIN 3317740-000 oHS) or 02131-010 on-RoHS)
1
J45 J4712
J49
J51J50
12
1
1
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
WDi(LM
J50
A03
9-131
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
08 Battery Cable agramsIFEPAK 20e Only) IN 3206579
J85
A07
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
WDiM Pin 1
J16
P161
26
9-132
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
09 26-Pin Cable agramsIN 3201241 Pin 1
J41
P411
26
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
WCa(LM
J51
9-133
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
10 Power/Therapy ble Diagrams
IFEPAK 20e Only)IN 3206857
J17
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
WCaM J47
P47
- ECG Analog Out - Ground
External Sync In Ground
9 - +5 volts DC out
6 - RS232 -DTR
8 - RS232 -RTS
2 - RS232 -TX
7 - RS232 -CTS
5 - Ground
3 - RS232 -RX
9-134
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
11 ECG Sync/System bles Diagrams
IN 3201997 DB-9
DB-15
1514
6 -5 -
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
WDi(LM
J49
9-135
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
13 AC Power Cable agrams IFEPAK 20e Only)IN 3206469
J43
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
WRe
t be removed before beginning this
0.312 screws (173) from the W06 ECG ase assembly. W06 ECG Connector from the bottom
ugh the connector hole.
P Connectors View Main Assemblies
9-136
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
06 ECG Connector moval
Note: The following assemblies musdisassembly:
– A07 Battery– Top case– Front case– Boardstack
To remove the W06 ECG Connector:1. Remove and discard the two 4-40
Connector located on the bottom c2. From outside the case, remove the
case and feed the ECG cable thro
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
WIn e W06 ECG Connector with the connector
onnector with the notch in the bottom into position. s (173) into the W06 ECG Connector;
en the first rib and the forward left corner
t in the bottom case.
PIP.
P Connectors View Main Assemblies
9-137
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
06 ECG Connector stallation
To install the W06 ECG Connector:1. On the outside of the case, align th
standoffs and align the key in the ccase and slide the ECG connector
2. Install two new 4-400.312 screwtorque to 6.8 in-lb.
3. Position the cable in the slot betweof the bottom case.
4. Place the first ferrite bead in its slo5. Install the boardstack.6. Install the front case.7. Install the top case.8. Install the A07 Battery.9. Complete the LIFEPAK 20 Device
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
WAsM(R32(n ECG Connector,
Inside View
9-138
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
06 ECG Connector sembly Diagrams
IN 3318315oHS) or 01010-009 on-RoHS)
J23
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
WCo
t be removed before beginning this
r Assembly:eal (268) from the W01 Therapy
m the back of the W01 Therapy
therapy connector from the bottom case the connector hole.
P Connectors View Main Assemblies
9-139
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
01 Therapy nnector Removal
Note: The following assemblies musdisassembly:
– A07 Battery– Top case– Front case– Boardstack
To remove the W01 Therapy Connecto1. Remove the Therapy Connector S
Connector.2. Remove the retaining ring (111) fro
Connector.3. From outside the case, remove the
and feed the therapy cable through
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
WCo
Assembly:y on the connector with the notch in the
erapy Connector Assembly into the
the back of the W01 Therapy Connector at the open end is visible.l (268) onto the W01 Therapy Connector.
PIP.
P Connectors View Main Assemblies
9-140
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
01 Therapy nnector Installation
To install the W01 Therapy Connector 1. From outside the case, align the ke
bottom case and slide the W01 Thbottom case.
2. Install the retaining ring (111) onto Assembly, and rotate the clip so th
3. Install the Therapy Connector Sea4. Install the boardstack.5. Install the front case.6. Install the top case.7. Install the A07 Battery.8. Complete the LIFEPAK 20 Device
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
WCoDiM(R32(n
4 5 6
10 11
3 7
9 12
812
9-141
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
01 Therapy nnector Assembly
agrams IN 3200474-009 oHS) or 00474-008 on-RoHS)
J13
J14
P14
P13
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
WCoW
ApexSternum+5v (vcc)Discharge switchCharge switchCharge LEDRecord switchEnergy selectCable sense (0)Cable sense (1)Cable parityCommon (Gnd)
731284569101112
9-142
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
01 Therapy nnector Assembly
iring DiagramWHT
WHT
NCNCNC
BRNREDORNYELGRNBLUVOIGRYWHTBLK
52347
12345678910
ferrite beads
ferrite beads
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
WRe
t be removed before beginning this
ssembly:) securing the SpO2 cable to the bottom removed to expose this tie wrap.rms on the SpO2 connector mounting clip
e bottom case.mbly away from the bottom case.
P Connectors View Main Assemblies
9-143
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
05 SpO2 Connector moval
Note: The following assemblies musdisassembly:
– A07 Battery– Top case– Front case– Boardstack– W03 IrDA Port
To remove the W05 SpO2 Connector A1. Remove the cable tie retainer (229
case. The W03 IrDA Port must be 2. Gently pull apart the plastic snap a
(113), away from the bottom case.3. Lift the mounting clip away from th4. Lift the W05 SpO2 connector asse
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
WIn
sembly:tor into the locating detail in the bottom
ting clip (113) in front of the mounting
g clip in and down onto the bottom case p arms click into position.ecure the ferrite bead to the bottom case.
PIP.
(Continued on next page)
P Connectors View Main Assemblies
9-144
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
05 SpO2 Connector stallation
To install the W05 SpO2 Connector As1. Place the W05 SpO2 input connec
case.2. Position the SpO2 connector moun
block detail on the bottom case.3. Press the SpO2 connector mountin
mounting block detail until the sna4. Install a cable tie retainer (229) to s5. Install the W03 IrDA Assembly.6. Install the boardstack.7. Install the front case.8. Install the top case.9. Install the A07 Battery.10. Complete the LIFEPAK 20 Device
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
WDiM
fold up here
fold up here fold up here
Folding dimensions
Back view
9-145
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
05 SpO2 Assembly agramsIN 3200925
Interconnect
P54P83
123456789
10
1413121110987654321
DET_ANODEDET_CATHODE
IR_CATHODE
RED_CATHODE
OUTER SHIELD
INNER SHIELD
Schematic diagram
1615 (MNTG-HOLE)
(MNTG-HOLE)
Front view Side view
P Back Index Next Page
LIF Replacement Procedures
B
WRe
t be removed before beginning this
l)
isconnect the W03 IrDA flex cable from removing the screw (255) using a 3/32
slot between the bottom case cutout (A)
driver. Bend the right IrDA snap tab (B) dge of the W03 IrDA Assembly.rom the bottom case. the bottom case, disconnect the IrDA
B at J8.
P Connectors View Main Assemblies
9-146
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
03 IrDA Assembly moval
Note: The following assemblies musdisassembly:
– A07 Battery– Top case– Front case– Boardstack (optional remova
To remove the W03 IrDA Assembly:1. If the boardstack is not removed, d
the A01 System PCB at J8 by firstallen driver.
2. Insert a slotted screwdriver into theand the right snap tab (B).
3. Gently apply pressure to the screwoutward slightly, freeing the right e
4. Remove the W03 IrDA Assembly f5. If the boardstack is still installed in
connector from the A01 System PCB
A
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
WIn n the bottom case. (The IrDA is located
n the bottom case.)to the slot between the bottom case ).driver. Bend the right IrDA snap tab (B)
n into the snap tabs and release the nap tabs will close around the W03 IrDA
ly is resting centered on the support
o the A01 System PCB at J08 and fasten en driver, if the boardstack is still installed tall the boardstack. The IrDA flex cable installation.
(Continued on next page)
P Connectors View Main Assemblies
9-147
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
03 IrDA Assembly stallation
To install the W03 IrDA Assembly:1. Position the W03 IrDA Assembly o
near the center of the front panel o2. Insert a large slotted screwdriver in
cutout (A) and the right snap tab (B3. Gently apply pressure to the screw
slightly outward, 4. Press the W03 IrDA Assembly dow
pressure on the screwdriver. The sAssembly.
5. Ensure that the W03 IrDA Assembbrackets and snap tabs.
6. Connect the W03 IrDA Assembly twith a screw (255) using a 3/32 allin the bottom case. Otherwise, Insis connected during the boardstack
B
A
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
WIn
PIP.
P Connectors View Main Assemblies
9-148
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
03 IrDA Assembly stallation (continued)
7. Install the front case.8. Install the top case.9. Install the A07 Battery.10. Complete the LIFEPAK 20 Device
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
WDiM(R32(n
three-dimensional view
9-149
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
03 IrDA Assembly agramsIN 3200926-007 oHS) or 00926-006 on-RoHS)
side viewfront view
Interconnect
P Back Index Next Page
LIF Replacement Procedures
B
WExRe
t be removed before beginning this
arness Extension Cable:ess Extension Cable from the W02 se removal).25 Speaker Harness Extension Cable art of boardstack removal).uring the ferrite ring to the bottom case.lder and feed the W25 Speaker Harness erapy Connector Assembly. Remove the C
P Connectors View Main Assemblies
9-150
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
25 Speaker Harness tension Cable moval
Note: The following assemblies musdisassembly:
– A07 Battery– Top case– Front case– Boardstack
Note: To remove the W25 Speaker H1. Disconnect the W25 Speaker Harn
Speaker Assembly (part of front ca2. Disconnect the other end of the W
from the A01 System PCB at J5 (p3. Cut the cable tie retainer (229) sec4. Remove the connector from the ho
Extension Cable under the W01 Thcable from the bottom case.
able tie retainer
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
B
WExIn
xtension Cable:xtension Cable under the W01 Therapy
xtension Cable into the holder in the
n the set of holes 0.5 inches to the left of mbly, and secure the extension cable’s
PIP.
P Connectors View Main Assemblies
9-151
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ottom Case (continued)
25 Speaker Harness tension Cable
stallation
To Install the W25 Speaker Harness E1. Feed the W25 Speaker Harness E
Connector Assembly.2. Insert the W25 Speaker Harness E
bottom case.3. Install the cable tie retainer (229) i
the W01 Therapy Connector Asseferrite ring to the bottom case.
4. Install the boardstack.5. Install the front case.6. Install the top case.7. Install the A07 Battery.8. Complete the LIFEPAK 20 Device
arts List Interconnect Diagram Module View
P Back Index Next Page
LIF Replacement Procedures
F
DeIn3232
he device with isopropyl alcohol.age).age for placement):
NoteA in Labels Assembly diagram
NG B in Labels Assembly diagram
NG B in Labels Assembly diagram
el C in Labels Assembly diagramD in Labels Assembly diagramE in Labels Assembly diagramF in Labels Assembly diagramSelect languageSN label illustration
ENG Select language
9-152
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly
vice Labeling cluding Label Set (12) 01640 - LIFEPAK 20 06034 - LIFEPAK 20e
To apply the labels to the device:1. Remove the old labels and clean t2. Select the correct label set (langu3. Apply the labels (refer to the next p
Item MIN (ref) Part Description12 - Label set 3201290 Rear connector label12 - Label set 3201274-030 Front connector label, E
(SpO2)12 - Label set 3201274-015 Front connector label, E
(no SpO2)12 - Label set 3201275 Physio-Control logo lab12 - Label set 3201273 Product ID label12 - Label set 3009060 FDA label 12 - Label set 3202375 Masimo patent label23 3201499 Manual latch label 183 3201643 Serial number label284 3206926-001 Label - Adult VF Dose,
P Back Index Next Page
LIF Replacement Procedures
F
LaDi
tion.
2-A12-B
12-C
12-DFront view
(No SpO2)
284
A15
9-153
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
bel Placement agrams
Refer to the parts list for label descrip
12-E
183
12-F
1
Bottom view Rear view
P Back Index Next Page
LIF Replacement Procedures
F
LIDeLa
Part Description
804 LIFEPAK 20 label set (no SpO2)
818 LIFEPAK 20 label set (with SpO2)
754 LIFEPAK 20e label set (no SpO2)
755 LIFEPAK 20e label set (with SpO2)
660 LIFEPAK 20e label set (no SpO2) 3rd Edition
661 LIFEPAK 20e label set (with SpO2) 3rd Edition
805 LIFEPAK 20 label set (no SpO2)
819 LIFEPAK 20 label set (with SpO2)
765 LIFEPAK 20e label set (no SpO2)
766 LIFEPAK 20e label set (with SpO2)
666 LIFEPAK 20e label set (no SpO2)3rd Edition
667 LIFEPAK 20e label set (with SpO2)3rd Edition
(Continued on next page)
9-154
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
FEPAK 20/20e vice Label Set nguages
Language MIN CAT.
English 3201640-500 21501-001
English 3201640-501 21501-001
English 3206034-006 21501-001
English 3206034-007 21501-001
English 3206034-008 21501-002
English 3206034-009 21501-002
French 3201640-506 21501-001
French 3201640-507 21501-001
French 3206034-084 21501-001
French 3206034-085 21501-001
French 3206034-086 21501-002
French 3206034-087 21501-002
P Back Index Next Page
LIF Replacement Procedures
F
LIDeLa
Part Description
806 LIFEPAK 20 label set (no SpO2)
820 LIFEPAK 20 label set (with SpO2)
761 LIFEPAK 20e label set (no SpO2)
762 LIFEPAK 20e label set (with SpO2)
662 LIFEPAK 20e label set (no SpO2)3rd Edition
663 LIFEPAK 20e label set (with SpO2)3rd Edition
807 LIFEPAK 20 label set (no SpO2)
821 LIFEPAK 20 label set (with SpO2)
769 LIFEPAK 20e label set (no SpO2)
770 LIFEPAK 20e label set (with SpO2)
670 LIFEPAK 20e label set (no SpO2)3rd Edition
671 LIFEPAK 20e label set (with SpO2)3rd Edition
9-155
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
FEPAK 20/20e vice Label Set nguages (continued)
Language MIN CAT.
German 3201640-502 21501-001
German 3201640-503 21501-001
German 3206034-044 21501-001
German 3206034-045 21501-001
German 3206034-046 21501-002
German 3206034-047 21501-002
Spanish 3201640-510 21501-001
Spanish 3201640-511 21501-001
Spanish 3206034-128 21501-001
Spanish 3206034-129 21501-001
Spanish 3206034-126 21501-002
Spanish 3206034-127 21501-002
P Back Index Next Page
LIF Replacement Procedures
F
LIDeLa
Part Description
808 LIFEPAK 20 label set (no SpO2)
822 LIFEPAK 20 label set (with SpO2)
763 LIFEPAK 20e label set (no SpO2)
764 LIFEPAK 20e label set (with SpO2)
664 LIFEPAK 20e label set (no SpO2)3rd Edition
665 LIFEPAK 20e label set (with SpO2)3rd Edition
809 LIFEPAK 20 label set (with SpO2)
823 LIFEPAK 20 label set (no SpO2)
776 LIFEPAK 20e label set (no SpO2)
777 LIFEPAK 20e label set (with SpO2)
676 LIFEPAK 20e label set (no SpO2)3rd Edition
677 LIFEPAK 20e label set (with SpO2)3rd Edition
(Continued on next page)
9-156
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
FEPAK 20/20e vice Label Set nguages (continued)
Language MIN CAT.
Italian 3201640-504 21501-001
Italian 3201640-505 21501-001
Italian 3206034-064 21501-001
Italian 3206034-065 21501-001
Italian 3206034-066 21501-002
Italian 3206034-067 21501-002
Swedish 3201640-516 21501-001
Swedish 3201640-517 21501-001
Swedish 3206034-184 21501-001
Swedish 3206034-185 21501-001
Swedish 3206034-186 21501-002
Swedish 3206034-187 21501-002
P Back Index Next Page
LIF Replacement Procedures
F
LIDeLa
Part Description
10 LIFEPAK 20 label set (with SpO2)
24 LIFEPAK 20 label set (with SpO2)
78 LIFEPAK 20e label set (no SpO2)
79 LIFEPAK 20e label set (with SpO2)
78 LIFEPAK 20e label set (no SpO2)3rd Edition
79 LIFEPAK 20e label set (with SpO2)3rd Edition
11 LIFEPAK 20 label set (no SpO2)
25 LIFEPAK 20 label set (with SpO2)
67 LIFEPAK 20e label set (no SpO2)
68 LIFEPAK 20e label set (with SpO2)
68 LIFEPAK 20e label set (no SpO2)3rd Edition
69 LIFEPAK 20e label set (with SpO2)3rd Edition
9-157
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
FEPAK 20/20e vice Label Set nguages (continued)
Language MIN CAT.
Danish 3201640-518 21501-0018
Danish 3201640-519 21501-0018
Danish 3206034-204 21501-0017
Danish 3206034-205 21501-0017
Danish 3206034-206 21501-0026
Danish 3206034-207 21501-0026
Dutch 3201640-508 21501-0018
Dutch 3201640-509 21501-0018
Dutch 3206034-104 21501-0017
Dutch 3206034-105 21501-0017
Dutch 3206034-106 21501-0026
Dutch 3206034-107 21501-0026
P Back Index Next Page
LIF Replacement Procedures
F
LIDeLa
Part Description
812 LIFEPAK 20 label set (no SpO2)
826 LIFEPAK 20 label set (with SpO2)
780 LIFEPAK 20e label set (no SpO2)
781 LIFEPAK 20e label set (with SpO2)
680 LIFEPAK 20e label set (no SpO2)3rd Edition
681 LIFEPAK 20e label set (with SpO2)3rd Edition
813 LIFEPAK 20 label set (no SpO2)
827 LIFEPAK 20 label set (with SpO2)
795 LIFEPAK 20e label set (no SpO2)
782 LIFEPAK 20e label set (with SpO2)
682 LIFEPAK 20e label set (no SpO2)3rd Edition
683 LIFEPAK 20e label set (with SpO2)3rd Edition
(Continued on next page)
9-158
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
FEPAK 20/20e vice Label Set nguages (continued)
Language MIN CAT.
Finnish 3201640-520 21501-001
Finnish 3201640-521 21501-001
Finnish 3206034-224 21501-001
Finnish 3206034-225 21501-001
Finnish 3206034-226 21501-002
Finnish 3206034-227 21501-002
Norwegian 3201640-522 21501-001
Norwegian 3201640-523 21501-001
Norwegian 3206034-244 21501-001
Norwegian 3206034-245 21501-001
Norwegian 3206034-246 21501-002
Norwegian 3206034-247 21501-002
P Back Index Next Page
LIF Replacement Procedures
F
LIDeLa
Part Description
14 LIFEPAK 20 label set (no SpO2)
28 LIFEPAK 20 label set (with SpO2)
83 LIFEPAK 20e label set (no SpO2)
94 LIFEPAK 20e label set (with SpO2)
84 LIFEPAK 20e label set (no SpO2)3rd Edition
85 LIFEPAK 20e label set (with SpO2)3rd Edition
15 LIFEPAK 20 label set (no SpO2)
29 LIFEPAK 20 label set (with SpO2)
71 LIFEPAK 20e label set (no SpO2)
73 LIFEPAK 20e label set (with SpO2)
72 LIFEPAK 20e label set (no SpO2)3rd Edition
73 LIFEPAK 20e label set (with SpO2)3rd Edition
(Continued on next page)
9-159
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
FEPAK 20/20e vice Label Set nguages (continued)
Language MIN CAT.
Polish 3201640-524 21501-0018
Polish 3201640-525 21501-0018
Polish 3206034-264 21501-0017
Polish 3206034-265 21501-0017
Polish 3206034-266 21501-0026
Polish 3206034-267 21501-0026
Portuguese 3201640-512 21501-0018
Portuguese 3201640-513 21501-0018
Portuguese 3206034-144 21501-0017
Portuguese 3206034-145 21501-0017
Portuguese 3206034-146 21501-0026
Portuguese 3206034-147 21501-0026
P Back Index Next Page
LIF Replacement Procedures
F
LIDeLa
Part Description
16 LIFEPAK 20 label set (no SpO2)
30 LIFEPAK 20 label set (with SpO2)
74 LIFEPAK 20e label set (no SpO2)
75 LIFEPAK 20e label set (with SpO2)
74 LIFEPAK 20e label set (no SpO2)3rd Edition
75 LIFEPAK 20e label set (with SpO2)3rd Edition
43 LIFEPAK 20 label set (no SpO2)
56 LIFEPAK 20 label set (with SpO2)
91 LIFEPAK 20e label set (no SpO2)
92 LIFEPAK 20e label set (with SpO2)
96 LIFEPAK 20e label set (no SpO2)3rd Edition
97 LIFEPAK 20e label set (with SpO2)3rd Edition
9-160
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
FEPAK 20/20e vice Label Set nguages (continued)
Language MIN CAT.
Brazilian 3201640-514 21501-0018
Brazilian 3201640-515 21501-0018
Brazilian 3206034-164 21501-0017
Brazilian 3206034-165 21501-0017
Brazilian 3206034-166 21501-0026
Brazilian 3206034-167 21501-0026
Japanese 3201640-536 21501-0009
Japanese 3201640-537 21501-0009
Japanese 3206034-404 21501-0017
Japanese 3206034-405 21501-0017
Japanese 3206034-406 21501-0026
Japanese 3206034-407 21501-0026
P Back Index Next Page
LIF Replacement Procedures
F
LIDeLa
Part Description
17 LIFEPAK 20 label set (no SpO2)
31 LIFEPAK 20 label set (with SpO2)
39 LIFEPAK 20e label set (no SpO2)
40 LIFEPAK 20e label set (with SpO2)
92 LIFEPAK 20e label set (no SpO2)3rd Edition
93 LIFEPAK 20e label set (no SpO2)3rd Edition
32 LIFEPAK 20 label set (no SpO2)
33 LIFEPAK 20 label set (with SpO2)
85 LIFEPAK 20e label set (no SpO2)
86 LIFEPAK 20e label set (with SpO2)
86 LIFEPAK 20e label set (no SpO2)3rd Edition
87 LIFEPAK 20e label set (with SpO2)3rd Edition
9-161
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
FEPAK 20/20e vice Label Set nguages (continued)
Language MIN CAT.
Chinese 3201640-532 21501-0018
Chinese 3201640-533 21501-0018
Chinese 3206034-344 21501-0015
Chinese 3206034-345 21501-0015
Chinese 3206034-346 21501-0026
Chinese 3206034-347 21501-0026
Hungarian 3201640-526 21501-0018
Hungarian 3201640-527 21501-0018
Hungarian 3206034-284 21501-0017
Hungarian 3206034-285 21501-0017
Hungarian 3206034-286 21501-0026
Hungarian 3206034-287 21501-0026
P Back Index Next Page
LIF Replacement Procedures
F
LIDeLa
(Continued on next page)
Part Description
34 LIFEPAK 20 label set (no SpO2)
35 LIFEPAK 20 label set (with SpO2)
87 LIFEPAK 20e label set (no SpO2)
88 LIFEPAK 20e label set (with SpO2)
88 LIFEPAK 20e label set (no SpO2)3rd Edition
89 LIFEPAK 20e label set (with SpO2)3rd Edition
36 LIFEPAK 20 label set (no SpO2)
37 LIFEPAK 20 label set (with SpO2)
89 LIFEPAK 20e label set (no SpO2)
90 LIFEPAK 20e label set (with SpO2)
90 LIFEPAK 20e label set (no SpO2)3rd Edition
91 LIFEPAK 20e label set (with SpO2)3rd Edition
9-162
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
FEPAK 20/20e vice Label Set nguages (continued)
Language MIN CAT.
Czech 3201640-528 21501-0018
Czech 3201640-529 21501-0018
Czech 3206034-304 21501-0017
Czech 3206034-305 21501-0017
Czech 3206034-306 21501-0026
Czech 3206034-307 21501-0026
Russian 3201640-530 21501-0018
Russian 3201640-531 21501-0018
Russian 3206034-324 21501-0017
Russian 3206034-325 21501-0017
Russian 3206034-326 21501-0026
Russian 3206034-327 21501-0026
P Back Index Next Page
LIF Replacement Procedures
F
LIDeLa
Part Description
38 LIFEPAK 20 label set (no SpO2)
39 LIFEPAK 20 label set (with SpO2)
41 LIFEPAK 20e label set (no SpO2)
42 LIFEPAK 20e label set (with SpO2)
94 LIFEPAK 20e label set (no SpO2)3rd Edition
95 LIFEPAK 20e label set (with SpO2)3rd Edition
9-163
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
FEPAK 20/20e vice Label Set nguages (continued)
Language MIN CAT.
Korean 3201640-534 21501-0018
Korean 3201640-535 21501-0018
Korean 3206034-384 21501-0015
Korean 3206034-385 21501-0015
Korean 3206034-386 21501-0026
Korean 3206034-387 21501-0026
P Back Index Next Page
LIF Replacement Procedures
F
MLa
NlatoD
-000767
-000924
-000925
-000767
-000932
-000925
-000924
-000930
-000929
-000925
-000928
(Continued on next page)
9-164
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
anual Latch Labelnguages
ote: To order the MANUAL tch label and the AED door gether as a kit refer to AED oor/Latch Label Kits.
Language MIN CAT.
English 3201499-900 21501
French 3201499-902 21501
German 3201499-901 21501
Spanish 3201499-900 21501
Italian 3201499-060 21501
Swedish 3201499-901 21501
Danish 3201499-902 21501
Dutch 3201499-100 21501
Finnish 3201499-220 21501
Norwegian 3201499-901 21501
Polish 3201499-260 21501
P Back Index Next Page
LIF Replacement Procedures
F
MLa
NlatoM
1-000767
1-000767
1-000926
1-000927
1-001349
1-001350
1-001351
1-001352
9-165
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
anual Latch Labelnguages (continued)
ote: To order the MANUAL tch label and the AED door gether as a kit refer to anual Latch Label Kits.
Language MIN CAT.
Portuguese 3201499-900 2150
Brazilian 3201499-900 2150
Japanese 3201499-400 2150
Chinese 3201499-340 2150
Hungarian 3201499-280 2150
Czech 3201499-300 2150
Russian 3201499-320 2150
Korean 3201499-380 2150
P Back Index Next Page
LIF Replacement Procedures
FAdLa
Sedi
01935
01858
01856
01860
01857
01862
01863
01859
01864
01865
01866
01861
01867
01868
01869
01870
01871
01872
9-166
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
ult VF Dose Labelnguages (284)
e Labels Assembly agram
Language MIN CAT.English 3206926-001 21501-0
French 3206926-081 21501-0
German 3206926-041 21501-0
Spanish 3206926-121 21501-0
Italian 3206926-061 21501-0
Swedish 3206926-181 21501-0
Danish 3206926-201 21501-0
Dutch 3206926-101 21501-0
Finnish 3206926-221 21501-0
Norwegian 3206926-241 21501-0
Polish 3206926-261 21501-0
Portuguese 3206926-141 21501-0
Hungarian 3206926-281 21501-0
Czech 3206926-301 21501-0
Russian 3206926-321 21501-0
Chinese 3206926-341 21501-0
Korean 3206926-380 21501-0
Japanese 3206926-401 21501-0
P Back Index Next Page
LIF Replacement Procedures
F
AEKi
K iption
3 202056) and Latch label (3201499)
3 202056) and Latch label (3201499)
3 202056) and Latch label (3201499)
3 202056) and Latch label (3201499)
3 202056) and Latch label (3201499)
3 202056) and Latch label (3201499)
3 202056) and Latch label (3201499)
3 202056) and Latch label (3201499)
3 202056) and Latch label (3201499)
9-167
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
D Door/Latch Labelts
it MIN CAT. Languages Part Descr
202360-027 21330-001007 English, Spanish, Portuguese, Brazilian
AED door (3
202360-028 21330-001008 German, Swedish, Norwegian
AED door (3
202360-029 21330-001009 Italian AED door (3
202360-030 21330-001010 French, Danish AED door (3
202360-031 21330-001011 Dutch AED door (3
202360-032 21330-001012 Finnish AED door (3
202360-033 21330-001013 Polish AED door (3
202360-034 21330-001014 Chinese AED door (3
202360-035 21330-001015 Japanese AED door (3
P Back Index Next Page
LIF Replacement Procedures
F
A1Ke
e for language MINs.)
(Continued on next page)
9-168
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
5 Elastomer ypad – All Options
(Refer to the parts list on the next pag
P Back Index Next Page
LIF Replacement Procedures
F
A1Ke
. Part Description
00-004598 Keypad (no Pacing)
00-004231 Keypad (with Pacing)
00-004740 Keypad (no Pacing)
00-004755 Keypad (with Pacing)
00-004741 Keypad (no Pacing)
00-004712 Keypad (with Pacing)
00-004744 Keypad (no Pacing)
00-004713 Keypad (with Pacing)
00-004743 Keypad (no Pacing)
00-004714 Keypad (with Pacing)
00-004742 Keypad (no Pacing)
00-004715 Keypad (with Pacing)
(Continued on next page)
9-169
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
5 Elastomer ypad - Languages
Language MIN CAT
English 3200642-106 213
English 3200642-091 213
French 3200642-107 213
French 3200642-092 213
German 3200642-108 213
German 3200642-093 213
Spanish 3200642-109 213
Spanish 3200642-094 213
Italian 3200642-110 213
Italian 3200642-095 213
Swedish 3200642-111 213
Swedish 3200642-096 213
P Back Index Next Page
LIF Replacement Procedures
F
A1Ke(c
. Part Description
0-004748 Keypad (no Pacing)
0-004716 Keypad (with Pacing)
0-004747 Keypad (no Pacing)
0-004717 Keypad (with Pacing)
0-004746 Keypad (no Pacing)
0-004718 Keypad (with Pacing)
0-004749 Keypad (no Pacing)
0-004719 Keypad (with Pacing)
0-004750 Keypad (no Pacing)
0-004729 Keypad (with Pacing)
0-004751 Keypad (no Pacing)
0-004720 Keypad (with Pacing)
(Continued on next page)
9-170
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
5 Elastomer ypad - Languages
ontinued)
Language MIN CAT
Danish 3200642-112 2130
Danish 3200642-097 2130
Dutch 3200642-113 2130
Dutch 3200642-098 2130
Finnish 3200642-114 2130
Finnish 3200642-099 2130
Norwegian 3200642-115 2130
Norwegian 3200642-100 2130
Polish 3200642-116 2130
Polish 3200642-101 2130
Portuguese 3200642-117 2130
Portuguese 3200642-102 2130
P Back Index Next Page
LIF Replacement Procedures
F
A1Ke(c
. Part Description
0-004752 Keypad (no Pacing)
0-004721 Keypad (with Pacing)
0-004753 Keypad (no Pacing)
0-004722 Keypad (with Pacing)
0-004754 Keypad (no Pacing)
0-004723 Keypad (with Pacing)
0-006164 Keypad (no Pacing)
0-006163 Keypad (with Pacing)
0-006167 Keypad (no Pacing)
0-006166 Keypad (with Pacing)
0-006170 Keypad (no Pacing)
0-006169 Keypad (with Pacing)
0-006173 Keypad (no Pacing)
0-006172 Keypad (with Pacing)
9-171
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
5 Elastomer ypad - Languages
ontinued)Language MIN CAT
Brazilian 3200642-118 2130
Brazilian 3200642-103 2130
Japanese 3200642-141 2130
Japanese 3200642-140 2130
Chinese 3200642-123 2130
Chinese 3200642-122 2130
Hungarian 3200642-126 2130
Hungarian 3200642-125 2130
Czech 3200642-129 2130
Czech 3200642-128 2130
Russian 3200642-132 2130
Russian 3200642-131 2130
Korean 3200642-135 2130
Korean 3200642-134 2130
P Back Index Next Page
LIF Replacement Procedures
F
In o the printer: the left side of the device to open the
aper chamber, with the end coming from
perly if the paper roll is inserted with the . The paper roll must be inserted with the
the paper end extends out of the side of
9-172
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
stalling Printer Paper To install a new roll of printer paper int1. Press the printer button located on
printer door.2. Remove the old roll of paper.3. Insert the new paper roll into the p
under the roll.Note: The printer will not print proend coming over the top of the rollend coming from under the roll.
4. Close the printer door. Ensure thatthe printer.
P Back Index Next Page
LIF Replacement Procedures
F
StLa
215
1
Asse guages Charge Button Languages
9-173
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
andard Paddles bels and Buttons 215
211
213 2x
Apex paddle
Sternum paddle
mbly Diagrams Parts 1–17 Parts 19–215 Label Lan
P Back Index Next Page
LIF Replacement Procedures
F
StPa
(Continued on next page)
Lab l Languages Charge Button Languages
It Note
29 r
21 Refer to Charge Button Languages
21
21 Refer to Standard Paddles Label Languages
9-174
(Continued on next page)
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
andard Paddles rts List
els and Buttons Assembly Diagrams Parts 19–215 Labe
em Quantity MIN CAT. Part Description
2 3200941-003 21330-001024 Standard paddle adapteassembly
1 1 3200648 various Charge button
3 2 3200943-000 21300-004710 Shock button
5 2 3202523 21501-000997 Paddle label
P Back Index Next Page
LIF Replacement Procedures
F
StLa
T.
01-000823
01-000823
01-000823
01-000824
01-000827
01-000823
01-000823
01-000823
01-000828
01-000823
01-000829
(Continued on next page)
Lab rts 19–215 Charge Button Languages
9-175
(Continued on next page)
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
andard Paddles Label nguages
Language MIN CA
English 3202533-000 215
French 3202533-000 215
German 3202533-000 215
Spanish 3202533-001 215
Italian 3202533-002 215
Swedish 3202533-000 215
Danish 3202533-000 215
Dutch 3202533-000 215
Finnish 3202533-003 215
Norwegian 3202533-000 215
Polish 3202533-004 215
els and Buttons Assembly Diagrams Parts 1–17 Pa
P Back Index Next Page
LIF Replacement Procedures
F
StLa
T.
501-000809
501-000809
501-000823
501-000807
501-001428
501-001429
501-001430
501-001431
Lab rts 19–215 Charge Button Languages
9-176
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
andard Paddles Label nguages (continued)
Language MIN CA
Portuguese 3202533-005 21
Brazilian 3202533-005 21
Japanese 3202533-000 21
Chinese 3202533-006 21
Hungarian 3202533-280 21
Czech 3202533-300 21
Russian 3202533-320 21
Korean 3202533-380 21
els and Buttons Assembly Diagrams Parts 1–17 Pa
P Back Index Next Page
LIF Replacement Procedures
F
ChLa
-004886
-004756
-004766
-004757
-004758
-004759
-004760
-004766
-004761
-004762
-004763
(Continued on next page)
Lab rts 19–215 Label Languages
9-177
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
arge Button nguages
Language MIN CAT.
English 3200648-015 21300
French 3200648-016 21300
German 3200648-902 21300
Spanish 3200648-017 21300
Italian 3200648-018 21300
Swedish 3200648-019 21300
Danish 3200648-020 21300
Dutch 3200648-902 21300
Finnish 3200648-021 21300
Norwegian 3200648-022 21300
Polish 3200648-023 21300
els and Buttons Assembly Diagrams Parts 1–17 Pa
P Back Index Next Page
LIF Replacement Procedures
F
ChLa
.
00-004767
00-004767
00-004764
00-004765
00-006328
00-006329
00-006330
00-006331
Lab rts 19–215 Label Languages
9-178
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
inal Assembly (continued)
arge Button nguages (continued)
Language MIN CAT
Portuguese 3200648-903 213
Brazilian 3200648-903 213
Japanese 3200648-024 213
Chinese 3200648-025 213
Hungarian 3200648-280 213
Czech 3200648-300 213
Russian 3200648-320 213
Korean 3200648-380 213
els and Buttons Assembly Diagrams Parts 1–17 Pa
P Back Index Next Page
LIF Replacement Procedures
S
omponents that support a particular
rt Description
-REPAIR, TOP CASE HANDLE
-REPAIR, FRONT CASE
REPAIR, DISPLAY FOR UI 3201966-005 D -006 (Pre-Redux)
REPAIR, BACKLIGHT INVERTER FOR UI 01966-005 AND -006 (Pre-Redux)
-REPAIR, POWER MODULE, LIFEPAK 20
-REPAIR, MASIMO SPO2 CONNECTOR
-REPAIR, THERAPY PCBA, PACING
-REPAIR, THERAPY PCBA, PACING
(Continued on next page)
9-179
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits
The service replacement kits include creplacement activity.
Kit MIN CAT. Pa
3202718-000 40402-000001 KIT
3202718-001 40402-000002 KIT
3202718-008 40402-000009 KITAN
3202718-009 40402-000010 KIT32
3202718-010 40402-000011 KIT
3202718-013 40402-000014 KIT
3202718-035 (RoHS)
40402-000028 KIT
3202718-016 (non-RoHS)
40402-000003 KIT
P Back Index Next Page
LIF Replacement Procedures
Srt Description
-REPAIR, THERAPY PCBA, NON PACING
-REPAIR, THERAPY PCBA, NON PACING
-REPAIR, OEM PCBA
-REPAIR, OEM PCBA
-REPAIR, PATIENT PARAMETER PCBA
-REPAIR, PATIENT PARAMETER PCBA
-REPAIR, PCB STACK
9-180
(Continued on next page)
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
Kit MIN CAT. Pa
3202718-036 (RoHS)
40402-000029 KIT
3202718-017 (non-RoHS)
40402-000004 KIT
3202718-037 (RoHS)
40402-000030 KIT
3202718-019 (non-RoHS)
40402-000006 KIT
3202718-038 (RoHS)
40402-000031 KIT
3202718-020 (non-RoHS)
40402-000007 KIT
3202718-021 40402-000017 KIT
P Back Index Next Page
LIF Replacement Procedures
S
art Description
IT-REPAIR, POWER MODULE, LIFEPAK 20e
IT-REPAIR, POWER MODULE, LIFEPAK 20e
IT-REPAIR, CAPACITOR BRACKET
IT-REPAIR, CAPACITOR,
IT-REPAIR, THERAPY CONNECTOR
IT-REPAIR, THERAPY CONNECTOR
IT-REPAIR, REDUX SC PCBA AND UI PCBA
IT-REPAIR, REDUX SC PCBA AND UI PCBA
9-181
(Continued on next page)
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
Kit MIN CAT. P
3202718-039 (RoHS)
40402-000032 K
3202718-022 (non-RoHS)
40402-000018 K
3202718-024 40402-000020 K
3202718-025 40402-000021 K
3202718-043 (RoHS)
40402-000036 K
3202718-026 (non-RoHS)
40402-000022 K
3202718-040 (RoHS)
40402-000033 K
3202718-029 (non-RoHS)
40402-000025 K
P Back Index Next Page
LIF Replacement Procedures
Sart Description
IT-REPAIR, SPO2 MODULE
IT-REPAIR, SPO2 MODULE
IT-REPAIR, MNC FLASH SPO2, IFEPAK 20e
IT-REPAIR, MNC FLASH SPO2, LIFEPAK 20e
IT-REPAIR, LED DISPLAY FOR Redux UI317230-000 (RoHS), Post-Redux UI 3317230-02 (RoHS) and 3201966-007 (non-RoHS) - LED isplay and Backlight for Redux UI PCB 317230-000 (RoHS), Post-Redux UI 3317230-02 (RoHS) or 3201966-007 (non-RoHS) or reater (requires Redux level PCB software set)
IT-REPAIR, Post Redux, UI, SC, Printer, RoHS
IT-REPAIR, Post Redux, UI, Printer, RoHS
9-182
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
Kit MIN CAT. P
3202718-041 (RoHS)
40402-000034 K
3202718-030 (non-RoHS)
40402-000026 K
3202718-042 (RoHS)
40402-000035 KL
3202718-031 (non-RoHS)
40402-000019 K
3202718-032 40402-000027 K30D30g
3202718-044 40402-000037 K
3202718-045 40402-000038 K
P Back Index Next Page
LIF Replacement Procedures
SIT-REPAIR, Post Redux, UI, RoHS
IT-REPAIR, Post Redux SC, RoHS
IT-REPAIR, Post Redux, Printer, RoHS
9-183
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
3202718-046 40402-000039 K
3202718-047 40402-000040 K
3202718-048 40402-000041 K
P Back Index Next Page
LIF Replacement Procedures
S
KITHAM
KITM
. Part Description
Top case handle
00-005334 Machine screw 6-32 x 1.75L
00-001032 Machine screw 6-32x0.375L
. Part Description
Front case, pad printed
00-004837 Cover plate, door
00-004836 Door hinge plate
00-004233 Display lens
00-005334 Machine screw 6-32 x 1.75L
00-001032 Machine screw 6-32x0.375L
9-184
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, TOP CASE NDLEIN 3202718-000
-REPAIR, FRONT CASEIN 3202718-001
Item Quantity MIN CAT
2 1 3200631
167 2 202253-592 213
169 2 3206185-001 213
Item Quantity MIN CAT
9 1 3200624
19 1 3200638-001 213
37 1 3200637-001 213
43 1 3200913-003 213
167 4 202253-592 213
169 2 3206185-001 213
P Back Index Next Page
LIF Replacement Procedures
S
KITUI (PrM
KITINV00M
T. Part Description
Active Color LCD Display
300-007774 Active Display Cable
300-004233 Display lens
300-001038 Screws 4-40 x 0.312
300-006141 Nylon snap rivet
T. Part Description
Backlight Inverter
00-004237 Active Backlight Inverter Cable
00-004838 Active Display Bracket
00-004250 Extender cable (for Sanyo display devices)
9-185
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, DISPLAY FOR 3201966-005 AND -006 e-Redux)IN 3202718-008
-REPAIR, BACKLIGHT ERTER FOR UI 3201966-
5 AND -006 (Pre-Redux)IN 3202718-009
Item Quantity MIN CA
A11 1 3205278-001
W15 1 3300152-000 21
43 1 3200913-003 21
173 4 202253-761 21
266 1 3205497-308 21
Item Quantity MIN CA
A08 1 3202033-500
W17 1 3200996-002 213
47 1 3200640-015 213
203 1 3202018-000 213
P Back Index Next Page
LIF Replacement Procedures
S
KITMOM
KITCOM
KITPAM(R32(n
T. Part Description
Power Supply module
T. Part Description
SpO2 Flex Assembly
SpO2 connector mounting clip
AT. Part Description
Therapy PCB with pacing
Therapy PCB with pacing
300-4242
ISO mount, Therapy
9-186
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, POWER DULE, LIFEPAK 20
IN 3202718-010
-REPAIR, MASIMO SPO2 NNECTOR
IN 3202718-013
-REPAIR THERAPY PCB, CINGIN 3202718-035 oHS) or 02718-016 on-RoHS)
Item Quantity MIN CA
A03 1 3202131-010
Item Quantity MIN CA
W05 1 3200925-006
113 1 3200921-000
Item Quantity MIN C
A04 1 3317228-000 (RoHS)
A04 1 3202259-010 (non-RoHS)
123 5 3201374-010 2100
P Back Index Next Page
LIF Replacement Procedures
S
KITWIM(R32(n
KITM(R32(n
T. Part Description
Therapy PCB without pacing
Therapy PCB without pacing
300-004242 ISO mount, Therapy
T. Part Description
OEM Interface PCB
OEM Interface PCB
00-008019 Machine screw, SEMS 4-40 x 5/16 L, split washer
00-005120 Screw-Cap, Hex,4-40 x 0.312 Nylon
9-187
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR THERAPY PCB, THOUT PACINGIN 3202718-036 oHS) or 02718-017 on-RoHS)
-REPAIR, OEM PCBAIN 3202718-037 oHS) or 02718-019 on-RoHS)
Item Quantity MIN CA
A04 1 3317228-001 (RoHS)
A04 1 3202259-011 (non-RoHS)
123 5 3201374-010 21
Item Quantity MIN CA
A06 1 3317224-000 (RoHS)
A06 1 3201950-004 (non-RoHS)
252 1 201874-002 213
255 1 3202489-031 213
P Back Index Next Page
LIF Replacement Procedures
S
KITPAM(R32(n
T. Part Description
Patient Parameter PCB
30-001266 Patient Parameter PCB
00-006430 Screw 4-40 1.000L
9-188
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, PATIENT RAMETER PCBAIN 3202718-038 oHS) or 02718-020 on-RoHS)
Item Quantity MIN CA
A06 1 3317226-000 (RoHS)
A06 1 3202680-002 (non-RoHS)
213
125 1 202253-772 213
P Back Index Next Page
LIF Replacement Procedures
S
KITM
T. Part Description
00-006430 Screw 4-40 1.000L
00-004236 Boardstack shield
00-004815 Standoff-M/M 0.250 hex, 0.375
00-004243 ISO mount, OEM
00-001038 Screw, 4-40 x 0.312L
00-008019 Machine screw SEMS 4-40 x 5/16 L, split washer
00-005187 ISO mount, Parameter
00-006038 Nomex shield
00-000580 Washer, 0.125ID, 0.312D
00-006593 Shield - EMI, PCB Stack
9-189
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, PCB STACKIN 3202718-021
Item Quantity MIN CA
125 1 202253-772 213
127 1 3200927-006 213
129 5 3201375-006 213
149 3 3201374-011 213
173 2 202253-761 213
252 5 201874-002 213
258 1 3201374-012 213
262 1 3203897-000 213
264 2 200804-102 213
278 1 3206405-000 213
P Back Index Next Page
LIF Replacement Procedures
S
KITMOM(R32(n
. Part Description
Power Supply module
Power Supply module
Battery Cable LIFEPAK 20e
Power/Therapy Cable, LIFEPAK 20e
ECG Sync/System Cables
AC Power Cable, LIFEPAK 20e
9-190
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, POWER DULE, LIFEPAK 20e
IN 3202718-039 oHS) or 02718-022 on-RoHS)
Item Quantity MIN CAT
A03 1 3317740-000 (RoHS)
A03 1 3202131-009 (non-RoHS)
W08 1 3206579
W10 1 3206857
W11 1 3201997
W13 1 3206469
P Back Index Next Page
LIF Replacement Procedures
S
KITBRM
. Part Description
00-004619 Capacitor Support Bracket
00-001038 Screw, 4-40 x 0.312L
00-006962 Dielectric shield
00-003883 Standoff, 0.188 hex, 0.562L
9-191
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, CAPACITOR ACKETIN 3202718-024
Item Quantity MIN CAT
95 2 3200922-000 213
173 4 202253-761 213
238 1 3206900-001 213
22 2 3202228-562 213
P Back Index Next Page
LIF Replacement Procedures
S
KITM T. Part Description
Energy Storage Capacitor
00-004307 Capacitor Discharge Cable
00-007458 Foam spacer
00-004110 Capacitor dielectric shield
00-000499 Cable tie retainer
00-004807 Foam, Capacitor end
00-005068 Inductive Resistor Assy.
00-004619 Capacitor bracket support
00-001038 Screw, 4-40 x 0.312L
00-003883 Standoff, 0.188 hex,0.562L
00-006962 Dielectric shield
00-007794 Poron Foam, Capacitor
9-192
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, CAPACITORIN 3202718-025 Item Quantity MIN CA
A13 1 3200846
W07 1 3202383-001 213
93 2 804447-36 213
162 1 3009787-003 213
229 1 200536-001 213
240 1 804447-041 213
260 1 3202773-000 213
95 2 3200922-000 213
173 4 202253-761 213
22 2 3202228-562 213
238 1 3206900-001 213
241 1 3300694-000 213
P Back Index Next Page
LIF Replacement Procedures
S
KITCOM(R32(n
. Part Description
Therapy Connector Assembly
Therapy Connector Assembly
00-000149 Therapy retaining ring
00-005784 Seal, therapy connector
9-193
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, THERAPY NNECTOR
IN 3202718-043 oHS) or 02718-026 on-RoHS)
Item Quantity MIN CAT
W01 1 3200474-009 (RoHS)
W01 1 3200474-008 (non-RoHS)
111 1 200040-001 213
268 1 3203445-001 213
P Back Index Next Page
LIF Replacement Procedures
S
KITPCM(R32(n
. Part Description
System Controller PCB
System Controller PCB
User Interface PCB
User Interface PCB
00-007774 Active Display Cable
00-006430 Screw 4-40 1.000L
00-004236 Boardstack shield
00-004815 Standoff-M/M 0.250 hex, 0.375
(Continued on next page)
9-194
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, REDUX SC BA AND UI PCBAIN 3202718-040 oHS) or 02718-029 on-RoHS)
Item Quantity MIN CAT
A01 1 3317227-002(RoHS)
A01 1 3201964-015 (non-RoHS)
A05 1 3317230-000 (RoHS)
A05 1 3201966-007 (non-RoHS)
W15 1 3300152-000 213
125 2 202253-772 213
127 1 3200927-006 213
129 5 3201375-006 213
P Back Index Next Page
LIF Replacement Procedures
S
KITPCM(R32(n
. Part Description
00-004704 Boardstack connector
00-004243 ISO mount, OEM
00-001038 Screws 4-40 x 0.312
00-004807 Spacer Foam, UI PCB
00-008019 Machine screw, SEMS 4-40 x 5/16 L, split washer
00-005187 ISO mount, Parameter
00-006038 Nomex shield
00-000580 Washer, 0.125ID, 0.312D
00-005578 ISO mount, System Controller (standoff)
00-006593 Shield - EMI, PCB Stack
9-195
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, REDUX SC BA AND UI PCBAIN 3202718-040 oHS) or 02718-029 on-RoHS) (continued)
Item Quantity MIN CAT
135 1 3201007-002 213
149 3 3201374-011 213
173 2 202253-761 213
240 1 804447-041 213
252 5 201874-002 213
258 1 3201374-012 213
262 1 3203897-000 213
264 2 200804-102 213
265 1 3201374-009 213
278 1 3206405-000 213
P Back Index Next Page
LIF Replacement Procedures
S
KITM(R32(n
. Part Description
OEM Module, Pulse Oximeter, 3336
OEM Module, Pulse Oximeter, 3336
00-008131 IrDA Flex Assembly
00-004235 IrDA Flex Assembly
00-008019 Machine screw, SEMS 4-40 x 5/16 L, split washer
9-196
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, SPO2 MODULE IN 3202718-041 oHS) or 02718-030 on-RoHS)
Item Quantity MIN CAT
A10 1 3318279 (RoHS)
A10 1 3308709 (non-RoHS)
W03 1 3200926-007 (RoHS)
213
W03 1 3200926-006 (non-RoHS)
213
252 4 201874-002 213
P Back Index Next Page
LIF Replacement Procedures
S
KITSPM(R32(n
T. Part Description
OEM Module, Pulse Oximeter, 3336 (MNC programmed)
OEM Module, Pulse Oximeter, 3336 (MNC programmed)
00-008131 IrDA Flex Assembly
00-004235 IrDA Flex Assembly
00-008019 Machine screw, SEMS 4-40 x 5/16 L, split washer
Software-Dual Flash, MNC MasimoSoftware-Dual Flash, MNC Masimo
9-197
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, MNC FLASH O2, LIFEPAK 20e (Nellcor)IN 3202718-042 oHS) or 02718-031 on-RoHS)
Item Quantity MIN CA
A10 1 3318279 (RoHS)
A10 1 3308709 (non-RoHS)
W03 1 3200926-007 (RoHS)
213
W03 1 3200926-006 (non-RoHS)
213
252 4 201874-002 213
0 0 3319549-000 (RoHS)
0 0 3207319-100 (non-RoHS)
P Back Index Next Page
LIF Replacement Procedures
S
KITFOan- Lfor0000(rePCMI
T. Part Description
Module-OEM, LED Driver (Backlight Inverter)
Active Display, Color LED
00-007774 Active Display Cable
00-004233 Display lens
00-004838 Active Display Bracket
00-001038 Screws 4-40 x 0.312
00-006141 Nylon snap rivet
9-198
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
-REPAIR, LED DISPLAY R UI 3317230-000 (RoHS) d 3201966-007 (non-RoHS) ED Display and Backlight Redux UI PCB 3317230-0 (RoHS) or 3201966-7(non-RoHS) or greater quires Redux level Bsoftware set)
N 3202718-032
Item Quantity MIN CA
A08 1 3308907
A11 1 3309555
W15 1 3300152-000 213
43 1 3200913-003 213
47 1 3200640-015 213
173 4 202253-761 213
266 1 3205497-308 213
P Back Index Next Page
LIF Replacement Procedures
S
KITUI,M
T. Part Description
Washer, Flat, Round, S, Zinc, 0.312D, 0.125ID
Screw-M, PH, CP, P, Sems, #4-40, 5-16 L, Split Washer
Screw-M, CS, Z, PH, Nylock, 4-40 X 1.000
Screw, Machine, Panead, Nylok, 4-40 X 1.000
Shield - PCB Stack
Connector-Board Stacker, Modified
Mount-Isolation, PCB, System Controller
Mount-Isolation, PCB, OEM
9-199
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
- REPAIR, POST REDUX SC, PRINTER, ROHSIN 3202718-044
Item Quantity MIN CA
2 200804-102
1 201874-002
16 202253-761
1 202253-772
1 3200927-006
1 3201007-002
1 3201374-009
3 3201374-011
P Back Index Next Page
LIF Replacement Procedures
S
KITUI,(coM
T. Part Description
Mount-Isolation, PCB, Parameter
Standoff - Male/Male, 0.250 HEX, 0.375L
Shield - Nomex
Shield - EMI, PCB Stack
Cable - Assembly, Active Color, RoHS
Screw, Machine, Panhead, Nylok, 6-32 X 1.750
Screw-PH, SS, P, Nylok, 6-32 X 0.375
Flex Assembly - UI To Stack
Screw-Cap, SKT HD, Hex Rec, 4-40, 0.312L, NYL
9-200
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
- REPAIR, POST REDUX SC, PRINTER, ROHS ntinued)IN 3202718-044
Item Quantity MIN CA
1 3201374-012
5 3201375-006
1 3203897-000
1 3206405-000
1 3300152-000
4 202253-592
2 3206185-001
1 3201000-004
2 3202489-031
P Back Index Next Page
LIF Replacement Procedures
S
KITUI,(coM
T. Part Description
Nut-Hex, SS, Lock 4-40 X 0.250W
Spacer-Foam, LP20 UI PCB
PCB Assy-Programmed System Controller, LP20
PCB Assy-Programmed User Interface, LP20
Printer-50MM, Thermal Printhead, RoHS
9-201
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
- REPAIR, POST REDUX SC, PRINTER, ROHS ntinued)IN 3202718-044
Item Quantity MIN CA
9 200805-000
1 80447-041
1 3317227-002
1 3317230-002
1 3318747-001
P Back Index Next Page
LIF Replacement Procedures
S
KITUI,M
T. Part Description
Screw-M, CS, Z, PH, Nylock, 4-40 X 0.312L
Cable-Assembly, Active Color, RoHS
Nut-Hex, SS, Lock 4-40 X 0.250W
Screw, Machine, Panhead, Nylok, 6-32 X 1.750
Screw-PH, SS, P, Nylok, 6-32 X 0.375
PCB Assy - Programmed User Interface, LP20
Printer-50MM, Thermal Printhead, RoHS
9-202
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
- REPAIR, POST REDUX PRINTER, ROHSIN 3202718-045
Item Quantity MIN CA
13 3202718-045
1 3300152-000
3 200805-000
4 202253-592
2 3206185-001
1 3317230-002
1 3318747-001
P Back Index Next Page
LIF Replacement Procedures
S
KITUI,M
T. Part Description
Screw-M, CS, Z, PH, Nylock, 4-40 X 0.312L
Cable-Assembly, Active Color, RoHS
Nut-Hex, SS, Lock 4-40 X 0.250W
Screw, Machine, Panhead, Nylok, 6-32 X 1.750
Screw-PH, SS, P, Nylok, 6-32 X 0.375
PCB Assy - Programmed User Interface, LP20
Printer-50MM, Thermal Printhead, RoHS
9-203
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
- REPAIR, POST REDUX ROHSIN 3202718-046
Item Quantity MIN CA
13 202253-761
1 3300152-000
3 200805-000
4 202253-592
2 3206185-001
1 3317230-002
1 3318747-001
P Back Index Next Page
LIF Replacement Procedures
S
KITSCM
T. Part Description
Washer, Flat, Round, S, Zinc, 0.312D, 0.125ID
Screw-M, PH, SP, P, Sems, # 4-40, 5-16 L, Split Washer
Screw-M, CS, Z, PH, Nylock, 4-40 X 0.312L
Screw, Machine, Panhead, Nylok, 4-40 X 1.000
Connector-board Stacker, Modified
Standoff - Male/Male, 0.250 Hex, 0.375L
Shield - Nomex
Screw, Machine, Panhead, Nylok, 6-32 X 1.750
9-204
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
- REPAIR, POST REDUX , ROHS IN 3202718-047
Item Quantity MIN CA
2 200804-102
1 201874-002
5 202253-761
1 202253-772
1 3201007-002
5 3201375-006
1 3203897-000
4 202253-592
P Back Index Next Page
LIF Replacement Procedures
S
KITSCM
T. Part Description
Screw-PH, SS, P, Nylok, 6-32 X 0.375
Nut-Hex, SS, Lock 4-40 X 0.250W
SCREW-CAP, SKT HD, HEX REC, 4-40, 0.312L, NYL
PCB Assy-Programmed System Controller, LP20
9-205
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
- REPAIR, POST REDUX , ROHS (continued)IN 3202718-047
Item Quantity MIN CA
2 3206185-001
6 200805-000
2 3202489-031
1 3317227-002
P Back Index Next Page
LIF Replacement Procedures
S
KITPRM
T. Part Description
Printer-50MM, Thermal Printhead, RoHS
9-206
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
ervice Replacement Kits (continued)
- REPAIR, POST REDUX, INTER, ROHS IN 3202718-048
Item Quantity MIN CA
1 3318747-001
P Back Index Next Page
LIF Replacement Procedures
D
em software replacement require tools Physio-Control. These procedures and mers using LIFENET System Asset ration and software can also be installed ersonnel.
rvices representative for assistance.
9-207
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
evice Software Replacement
Device configuration settings and systand procedures that are proprietary totools may be available for use by custoManagement products. Device configuby authorized Physio-Control service pContact a Physio-Control customer se
P Table of Contents Section Contents Back Index Next Page
LIF Defibrillator/Monitor Replacement Procedures
D Number and Serial Number
PN el The device serial number (SN) and part number (PN) are noted on a label on the bottom of the device.
9-208
01643-020K 20 2nd Edition
Conforms to medical device directive93/42/EEC
Splash proof per IEC 60529
Operating voltageAC line frequency
Power consumption Volt-Amperes
8-digit serial number
10-digit part number
Year of manufacture
CSA certification for Canada and the United States
Do not dispose in unsorted waste stream 11-digit catalog
number
Chinese environmentally friendly use period
Consult operating instructions
3201643-025LIFEPAK 20e 2nd Edition
revious Page
EPAK 20/20e
evice Part
and SN Lab
32LIFEPA
P Table of Contents Section Contents Back Index Next Page
LIF Defibrillator/Monitor Replacement Procedures
D Number and Serial Number (continued)
PN l The device serial number (SN) and part number (PN) are noted on a label on the bottom of the device.
9-209
01643-021 20 no CE Mark
3201643-026LIFEPAK 20e no CE Mark
revious Page
EPAK 20/20e
evice Part
and SN Labe
32LIFEPAK
P Back Index Next Page
LIF Replacement Procedures
D ntinued)
t number (PN) are noted on a label on the
9-210
PN
3201643-030LIFEPAK 20e 3rd Edition,
no CE Mark
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
evice Part Number and Serial Number (co
The device serial number (SN) and parbottom of the device. and SN Label
3201643-029LIFEPAK 20e 3rd Edition
P Back Index Next Page
LIF Replacement Procedures
D tinued)
UnNu
3202487-072, reflects the device options, nd so forth.
UnSe
ted to the sales order created during the serial number label on the bottom of ing to order parts.
9-211
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
evice Part Number and Serial Number (con
derstanding the Part mber
The device part number, for example, features, language, operating power, a
derstanding the rial Number
The serial number for the device is reladevice manufacturing and appears on the device. Use this number when call
P Back Index Next Page
LIF Replacement Procedures
O
io-Control representative. In the USA, call er and serial number located on the bly numbers, MINs (part numbers),
ns. Parts may be substituted to reflect s.
M u may also need the device g date is available for viewing by
Se ies the manufacturing conditions and e. When ordering parts, use the serial bottom of the device.
9-212
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
rdering Parts
To order parts, contact your local Phys1.800.442.1142. Provide the part numbbottom of the device. Specify all assemreference designations, and descriptiodevice modifications and improvement
anufacturing Date In some cases when ordering parts, yomanufacturing date. This manufacturinaccessing the Device Log.
rial Number The serial number of the device identifelements used in producing your devicnumber (SN) listed on the label on the
LIF Section Contents
P Back Index Next Page
LIS
n the Operating Instructions for the device. in this section.
EPAK 20/20e Defibrillator/Monitor
revious Page Table of Contents
3FEPAK 20/20e pecifications
Detailed specifications are provided iAdditional specifications are included
P Back Index Next Page
LIF LIFEPAK 20/20e Specifications
G
Op 68°F) unless otherwise stated.itor has seven main operating modes:erating capability for ALS userserating capability for BLS usersrint, edit or delete previous patient
onfigure the instrumentxecute device diagnostic tests and
waveforms for demonstration purposesmatic tests of critical circuits
10-2
revious Page Table of Contents Section Contents
EPAK 20/20e Defibrillator/Monitor
eneral
eration Modes Note: All specifications are at 20°C (The LIFEPAK 20/20e defibrillator/monManual Mode - Provides normal opAED Mode - Provides normal opArchive Mode - Allows operator to p
recordsSetup Mode - Allows operator to cService Mode - Allows operator to e
calibrationsInservice Mode - Provides simulatedAuto Test Mode - Provides daily auto
Top Related