7/28/2019 ir mq relay
1/10
;lIR:-
MQ:-
RELAY:-
7/28/2019 ir mq relay
2/10
DIGITAL INPUTS
Digital inputs can be define as that which inputs those having in digital
signal condition i.e. high or low, either Vs or VE on other hand in binary
form 1 or 0 these types of signal are known as digital inputs signals. These
digital inputs are provide by digital sensor modules or switches.
Here we use for digital inputs some switches and IR sensor digi ta lmodu lewhich gives us a digital inputs to the controlling part of this project
IR Module
In this tutorial we will see how to make simple infrared sensor module for
detecting reflecting surface. This sensor can be used to detect reflecting
silver/white strip, obstacle detection, flame detection, etc. These sensors
are primary requirement of any simple line follower robocar.
WORKING OF IR SENSORS
7/28/2019 ir mq relay
3/10
IR LED emits infrared radiation. This radiation illuminates the surface in
front of LED. Surface reflects the infrared light. Depending on reflectivity of
the surface, amount of light reflected varies. This reflected light is made
incident on reverse biased IR sensor. When photons are incident on
reverse biased junction of this diode, electron-hole pairs are generated,
which results in reverse leakage current. Amount of electron-hole pairs
generated depends on intensity of incident IR radiation. More intense
radiation results in more reverse leakage current. This current can be
passed through a resistor so as to get proportional voltage. Thus as
intensity of incident rays varies, voltage across resistor will vary
accordingly.
This voltage can then be given to OPAMP based comparator. Output of the
comparator can be read.
IR LED is used as a source of infrared rays. It comes in two packages 3mm
or 5mm. 3mm is better as it is requires less space. IR sensor is nothing but
a diode, which is sensitive for infrared radiation. This infrared transmitter
and receiver is called as IR TX-RX pair. It can be obtained from any
decent electronics component shop and costs less than 10Rs. Following
snap shows 3mm and 5mm IR pairs. Colour of IR transmitter and receiver
is different. However you may come across pairs which appear exactly
same or even has opposite colours than shown in above pic and it is not
possible to distinguish between TX and RX visually. In case you will have
to take help of multimeter to distinguish between them
The IR LED is just like any other LED, in that a current-limiting resistor is
useful to control the device current and therefore the light intensity. With a
100 ohm resistor and the approximately 1.5V forward voltage drop of the IR
LED, we'll have a LED current of about 35mA. That's fairly high, but more
light emitted will yield more light coming back to our sensor.
The phototransistor is a device with an exposed silicon junction. When light
passes through the plastic casing, most non-IR wavelengths are simply
absorbed by the plastic, but the infrared light makes it to the sensor within.
7/28/2019 ir mq relay
4/10
Each photon striking the silicon junction causes an electron to flow.
Because this is a phototransistor and not a photodiode, this current is
multiplied by the transistor's current gain, so each photon may actually
cause perhaps 10 to 100 electrons to flow. This current has nowhere to go
except through the 10K resistor, and as the current passes through the
resistor, the voltage across the resistor rises (V=IR). This change in voltage
is read by our microcontroller's Analog to Digital Converter (ADC).
MQ5 (LPG DETECTOR SESNOR)
LM358
7/28/2019 ir mq relay
5/10
FEATURES
High sensitivity to LPG, iso-butane, propane
Small sensitivity to alcohol, smoke.
* Fast response . * Stable and long life * Simple drivecircuit
APPLICATION
They are used in gas leakage detecting equipments in family
and industry, are suitable for detecting of LPG, iso-butane,
propane, LNG, avoid the noise of alcohol and cooking fumes and
cigarette smoke.
Structure and configuration of MQ-6 gas sensor is (Configuration
A or B), sensor composed by micro AL2O3 ceramic tube, Tin
Dioxide (SnO2) sensitive layer, measuring electrode and heater
are fixed into a crust made by plastic and stainless steel
net. The heater provides necessary work conditions for work
of sensitive components. The enveloped MQ-6 have 6 pin ,4 ofthem are used to fetch signals, and other 2 are used for providing
heating current.
7/28/2019 ir mq relay
6/10
12V RELAY
A relay is a switch which is
operated by electricity.
It is usually electromagnetic
device which has coil.
When this coil is supplied with
power, a magnetic field
created and will operate
mechanical switch.
There are solid state relays
which do not have moving
parts but are very expensive
compared to small
mechanical relays. Pictures in
this page shows typical small
electro mechanical relay.
Relay is used when we need
to handle high voltages and
currents through
microcontroller operated
system.
7/28/2019 ir mq relay
7/10
7/28/2019 ir mq relay
8/10
A relay is a switch which is operated by electricity. It is usually electromagnetic device whichhas coil. When this coil is supplied with power, a magnetic field created and will operate
mechanical switch. There are solid state relays which do not have moving parts but are veryexpensive compared to small mechanical relays. Pictures in this page shows typical small electro
mechanical relay. Relay is used when we need to handle high voltages and currents through
microcontroller operated system.
elay coil's current requirement is usually more than 100mA (for small relay about 100mA) and
microcontroller cant supply this much of current to relay by it self. So as shown in followingschematic diagram, we have to use transistor to handle this current requirement. Base pin of
NPN transistor used here is connected to ground pin via resistor to make sure that relay will stayoff when microcontroller does not output +5V to transistors base. This will make sure only logic
1 on microcontroller pin will activate relay. It is better to use Darlington transistor to handlecurrent requirement for relay, because darlington transistor can handle more current than single
transistor.
It is essential to connect a diode across relay coil in reverse bias to protect transistor form back
EMF created when relay is released from energized or ON state. If this diode is not used,
transistor and/or microcontroller which is driving relay may be damaged upon releasingenergized relay. The diode will short out the back EMF produced by coil when it turned OFF
from ON state.
7/28/2019 ir mq relay
9/10
Transistor
The BC548 is a general purposeepitaxialsiliconNPNbipolar junction transistorfound commonly in
European electronic equipment. The part number is assigned byPro Electron, which allows many
manufacturers to offer electrically and physically interchangeable parts under one identification. The
BC548 is commonly available in European Union countries. It is often the first type of bipolar transistor
young hobbyists encounter, and is often featured in circuit diagrams and designs published
http://en.wikipedia.org/wiki/Epitaxyhttp://en.wikipedia.org/wiki/Epitaxyhttp://en.wikipedia.org/wiki/Epitaxyhttp://en.wikipedia.org/wiki/NPN_transistorhttp://en.wikipedia.org/wiki/NPN_transistorhttp://en.wikipedia.org/wiki/Bipolar_junction_transistorhttp://en.wikipedia.org/wiki/Bipolar_junction_transistorhttp://en.wikipedia.org/wiki/Bipolar_junction_transistorhttp://en.wikipedia.org/wiki/Pro_Electronhttp://en.wikipedia.org/wiki/Pro_Electronhttp://en.wikipedia.org/wiki/Pro_Electronhttp://en.wikipedia.org/wiki/Pro_Electronhttp://en.wikipedia.org/wiki/Bipolar_junction_transistorhttp://en.wikipedia.org/wiki/NPN_transistorhttp://en.wikipedia.org/wiki/Epitaxy7/28/2019 ir mq relay
10/10
Top Related