INDUSTRIAL HYGIENE PERSONAL PROTECTIVE EQUIPMENT
Personal Protective Equipment
Introduction Eye & Face Protection Head Protection Hand Protection Foot Protection Body Protection Course Test
Introduction Occupational Health & Safety
Administration established 29 CFR 1910.132-138 the Personal Protective Equipment Standard
Briefly stated, this standard requires that employers must provide at no cost to their employees PPE when such equipment is necessary to protect employees from job related injuries, illnesses and fatalities
Payment for PPE
When PPE is required to protect employees, it must be provided by the employer at no cost to employees, except for specific items, such as:Safety-toe footwearPrescription safety eyewearEveryday clothing and weather-related gearLogging boots
Protecting Employees from Workplace Hazards
Employers must protect employees from workplace hazards and dangerous work procedures that can cause injury, illness and fatalities.
Employers must:Use all feasible engineering and work practice
controls to eliminate and reduce hazardsThen use appropriate PPE if these controls do
not eliminate hazardsRemember: PPE is the last control
General ProvisionsEvery employer :
1.Shall at his own expense furnish his workers with protective equipment for the eyes, face, hands andfeet, protective shields and barriers whenever necessary by reason of the hazardous nature of theprocess or environment, chemical or radiological or other mechanical irritants or hazards capable of causing injury or impairment in the function of any part of the body through absorption, inhalation or physical contact.
2.Deduction for the loss or damage of personal protective equipment shall be governed by Article114, Book III, Labor Code of the Philippines, and Section 14, Rule VIII, Book III, Omnibus RulesImplementing the Labor Code.
All personal protective equipment shall be of the approved design and construction appropriatefor the exposure and the work to be performed.
The employer shall be responsible for the adequacy and proper maintenance of personalprotective equipment used in his workplace.
No person shall be subjected or exposed to a hazardous environmental condition withoutprotection
Employer Responsibilities Assessment
Employers are required to conduct an assessment to determine the various physical hazards that may be present in your work area
Physical hazards include: Sources of motion Sources of high and low temperatures Sources of light radiation
○ welding ○ brazing ○ heat treating ○ high intensity lights
Sources of falling objects Sources of sharp objects Sources of rolling or pinching objects Sources of electric hazards Sources of slip, trips, and falls Sources of harmful dusts
Employer Responsibilities
Assessment
As part of the assessment, employers must also determine the various health hazards that may be present in your work area
Health hazards include: Types of chemicals hazards Sources of biological hazards Sources of nuclear radiation
Employer Responsibilities
Selection and Provision of PPE Once your area has been assessed, your employer must
select, with your help, appropriate personal protection equipment for you to use while performing your job
Once your area has been assessed, your employer must provide, at no cost to you, appropriate personal protection equipment that fits, for you to use while performing your job NOTE: If you have your own personal protective equipment, it
must be approved by your employer before you can use it on the job. Check with your supervisor or safety manager before using your own equipment
In addition to providing you with PPE, your employer must maintain the PPE used by employees. If a piece of PPE cannot be repaired, it must be discarded and replaced.
Your employer must maintain records of the workplace assessment and of your training
Employee Responsibilities
You are responsible for attending all PPE training sessions
You are responsible for wearing your assigned PPE Follow ALL Warnings and Precautions
Take time to read any and all warnings and precautions that may appear on tools, equipment, chemicals, MSDSs, and personal protective equipment
Listen and Follow Directions Listen and follow the directions that you may be given by
your supervisor or safety manager. They want you to return home today, and everyday, safe and sound to your family and friends
Report Report any and ALL unsafe conditions you may find in your
work area to your supervisor or safety manager. REMEMBER: Safety is a team effort!
Is This An Appropriate Hard Hat?
Is This An AppropriateRespirator?
Is This an AppropriateWelder’s Mask?
Is This an AppropriateScaffolding?
Training
Employees required to use PPE must be trained to know at least the followingWhen PPE is necessaryWhat type of PPE is necessaryHow to properly put on, take off, adjust, and
wearLimitations of the PPEProper care, maintenance, useful life and
disposal
Eye and Face Protection
Why Eye and Face Protection is Important
Thousands of people are blinded each year from work related eye injuries. Injuries that could have been prevented, if only people would have used eye or face protection.
Eye and Face Protection
Types of eye/face hazards
ImpactHeatChemicalsDustLight and/or Radiation
Eye and Face Protection
Potential Incidences of Eye/Face HazardsObject Striking EyesDusts, Powders, Fumes, and Mists
○ Small particles of matter can enter your eyes and damage them. Operations such as grinding, chiseling, sanding, hammering, and spraying can create small airborne particles
Contact with ChemicalsToxic Gases, Vapors, and Liquids
○ Toxic chemicals in the form of gases, vapors, and liquids can damage your eyes. Always read the appropriate MSDS before working with any hazardous material.
○ Always check with your supervisor or safety manager to learn the type of eye or face protection you will need to use in order to work safely
Eye and Face Protection
Potential Incidences of Eye/Face Hazards
Swinging Objects○ Large objects such as:
1. swinging chains, cables and ropes; 2. tools that are thrown or fall;
Thermal and Radiation Hazards ○ Operations such as welding, metal cutting,
and working around furnaces can expose your eyes to heat, glare, ultraviolet, and infrared radiation
Eye and Face Protection
Elimination or Control of Hazards Machine Guards
○ Many types of machines such as lathes, grinders, and sanders are equipped with guards, shields and screens
Work Area Barriers ○ Operations such as sanding, grinding, welding, and lathe
operations produce dust, vapors, and flying particles. To protect other workers, work area barriers such as movable screens and barriers should be set up to separate workers and bystanders from hazardous operations
Eye and Face Protection
Eye and Face Protection
Elimination or Control of HazardsVentilation
○ Ventilation, along with damping systems, can significantly reduce the amount of airborne particles that could be hazardous to your eyes
Lighting ○Good
lighting reduces eye strain and glare
Eye and Face Protection
Elimination or Control of Hazards Signs and Warnings
○ Obstructions and protruding objects should be identified and marked
Eyewash Stations ○ Eyewash stations should be
located within 100 feet of your work area. If you accidentally get something in your eyes, go directly to the eyewash station and flush your eyes with water for 15 minutes. Be sure to hold your eyes open with your fingers and "look" directly into the water streams.
Eye and Face Protection
Elimination or Control of HazardsSafe Work Practices
○ Read and follow all warnings and precautions that may be found on equipment and hazardous materials
○ Do not throw tools or participate in horseplay ○ Keep sharp or pointed objects away from
your eyes ○ Follow your supervisor's or safety
manager's suggestions and recommendations for working safely
Eye and Face Protection
Proper Fit and Use of PPEMust be right PPE for right job
○ Ex. Safety glasses are not sufficient eye protection for working with chemicals
Must stay on face during all work activities○ Ex. Should not slide off face or pinch side of
head and create a headache
Eye and face protective equipment shall conform with the following minimum requirements:
(1) provide adequate protection against the particular hazard for which they are designed or intended;
(2) be reasonably comfortable to use;
(3) fit snugly and shall not unduly interfere with the movements of the user;
(4) be durable, easily cleaned and capable of being disinfected;
(5) be kept clean and in good condition, and
(6) be of the approved type.
Eye and Face Protection
TYPES OF EYES AND FACE PROTECTIVE EQUIPMENTSafety GlassGogglesFace ShieldsWelding HelmetsAbsorptive Lenses
Eye and Face Protection
Regular glasses or sunglasses are not appropriate SAFETY GLASSES
Eye and Face Protection
SAFETY GLASSES
Eye and Face Protection
Safety Glasses much stronger and more resistant to impact and heat than
regular glasses equipped with side shields that give you protection from
hazards that may not be directly in front of you Safety glasses should be Z-87 approved to meet OSHA
regulations Should fit comfortable on face through all job tasks. Ensure that
glasses are not too big or too tight Limitation
○ Does not seal around eyes, could allow small droplets to come in contact with eyes
Eye and Face Protection
GOGGLES
Eye and Face Protection
Goggles surround the eye area, they give you more protection
in situations where you might encounter splashing liquids, fumes, vapors, powders, dusts, and mists
must indicate that they are chemical splash goggles to be worn for that purpose
Limitation○ Uncomfortable to wear with other head gear like helmet, ear muffs
or respirator
Eye and Face Protection
FACE SHIELDS
Eye and Face Protection
Face Shields full face protection used around operations which expose you to
molten metal, chemical splashes, or flying particles
Can be used simultaneously as a hard hatLimitations
○ Are not considered eye protection, will need to wear goggles or glasses underneath
○ Can fog up if working in poorly ventilated area
Eye and Face Protection Face shield used by
an employee working with molten metal
The molten metal bubbled and burst onto the face shield of the employee
The employee did not receive any injuries from the incident
Eye and Face Protection
WELDING HELMETS
Eye and Face Protection
Welding Helmets provide both face and eye protection use special absorptive lenses that filter the
intense light and radiant energy that is produced during welding operations
Limitations○ Heavy and hot, fog up○ Must wear safety glasses or goggles
underneath helmet
Eye and Face Protection
Absorptive Lenses additional protection if you must work
where there is bright light or glare Limitations
○ Must be used in conjunction with safety glasses or goggles
Eye and Face Protection
Safety Tip
Contact Lenses Wear your contacts with
caution if you work in areas where you might be exposed to fumes, dusts, powders, vapors, chemical splashes, molten metals, or intense heat, light or glare
Some chemicals can react with contacts and cause permanent injury
Eye and Face ProtectionCare of Eye Protection Equipment Clean your eye protection equipment. You can
usually use mild soap and water Never use abrasive soaps, rough paper, or cloth towels
Keep PPE in good working conditionIf damaged, replace as soon as possible
Store your eye protection equipment in a sanitary, cool, dry area away from moisture
Read the manufacturer's directions and warnings before using any eye protection equipment
If you have any questions concerning your eye protection equipment, talk with your supervisor or safety manager
Respiratory Protectionthe employer shall institute a respiratory protective program which shall
include the following:
(1) Proper selection of respirators on the basis of the hazards to which the workers exposed;
(2) Sufficient instruction and training in the proper use and the limitations of respirators;
(3) When practicable, the assignment of respirators to individual workers for their exclusive use;
(4) Regular cleaning and disinfecting of the respirators. Respirators issued for the exclusive use of one worker shall be cleaned after each day's use or as often as necessary. Those used by two or more workers shall be thoroughly cleaned and disinfected after each use;
(5) Appropriate examination and testing of the conditions of the work area in order to assure that the allowable degree of employee exposure is maintained, and to determine the effectiveness of the control measures
Head Protection
Why is Head Protection Important? In and around your head are:
Your eyes, with which you see Your ears, with which you hear Your nose, with which you smell Your mouth, with which you eat and speak Your brain, with which you think
Injuries to the head are very serious. For this reason, head protection and safety are very important .
Head Protection
Types of Head hazards
Impact Electric shock Drips
Head Protection
Potential Incidences of Head HazardsImpact
○ Falling or flying objects○ falling or walking into hard objects○ injuries include neck sprains, concussions,
and skull fracturesElectric Shock
○ Live exposed electric wires○ Injuries include electrical shocks and burns
Drips○ Toxic liquids such as acids, caustics, and
molten metals can irritate and burn the head/scalp.
Head Protection
Elimination or Control of Hazards Safe Work Practices Grounded equipment/shock resistant tools Signs posted warning of hazards
Head Protection
Types of Head PPE
Hard HatsClass A Hard HatClass B Hard HatClass C Hard hatBump Cups
Head Protection
HARD HAT
Head Protection
Hard hats A rigid shell that resists and deflects
blows to the head A suspension system inside the hat
that acts as a shock absorber Some hats serve as an insulator
against electrical shocks Shields your scalp, face, neck, and
shoulders against splashes, spills, and drips
Some hard hats can be modified so you can add face shields, goggles, hoods, or hearing protection to them
Head Protection
Class A Hard Hats Class B Hard Hats
Class C Hard Hats Bump Caps
Head Protection Class A Hard Hats
Protect you from falling objects Protect you from electrical
shocks up to 2,200 volts Class B Hard Hats
Protect you from falling objects Protect you from electrical
shocks up to 20,000 volts Class C Hard Hats
Protect you from falling objects Bump Caps
Bump caps are made from lightweight plastic and are designed to protect you from bumping your head on protruding objects
Head Protection
Modification of Hard HatDrilled holes for venting
reliefInserted pencil holder on
hat for easy retrieval Hard hat from
employee holding ladderEmployee on ladder
dropped screw driverScrew driver landed on
hard hat and stuck in
Head Protection
Hard hat test performed by AirforceThe Airforce hard
hats are different in shape but are rated the same for impact
Head ProtectionProper use and care of hard hat Always wear your hard hat while you are working in
areas where there are potential head hazards Adjust the suspension inside your hard hat so that the
hat sits comfortably, but securely on your head Inspect the shell of your hard hat for cracks, gouges,
and dents. Inspect the suspension system for frayed or broken straps. If your hard hat needs to be repaired, have it repaired immediately or ask your employer for a new one
Place plastic (non-metal) reflective tape on hat if working at night
Never paint, scratch or drill "air holes" in your hard hat Never carry personal belongings such as cigarettes,
lighters, or pens in your hard hat
Head Protection
Care and Maintenance of Hard Hat
Clean your hard hat at least once a month by soaking it in a solution of mild soap and hot water for 5-10 minutes
Because sunlight and heat can damage the suspension of your hat, always store your hat in a clean, dry, and cool location
Hand Protection
Why is Hand Protection Important?
It has been estimated that almost 20% of all disabling accidents on the job involve the hands
Without your fingers or hands, your ability to work would be greatly reduced
Hand Protection
Types of Hand HazardsTraumatic Injuries
Contact Injuries
Repetitive Motion Injuries
Hand Protection
Potential Incidences of Hand Hazards
Traumatic Injuries Tools and machines
with a sharp edges can cut your hands. ○ Staples, screwdrivers,
nails, chisels, and stiff wire can puncture your hands.
○ Getting your hands caught in machinery can sprain, crush, or remove your hands and fingers
Hand ProtectionPotential Incidences of Hand Hazards
Contact InjuriesComing into contact with
caustic or toxic chemicals, biological substances, electrical sources, or extremely cold or hot objects can irritate or burn your hands ○ WARNING: Toxic substances
are poisonous substances that can be absorbed through your skin and enter your body.
Hand ProtectionRepetitive Motion Injuries
Whenever you repeat the same hand movement over a long period of time, you run the risk of repetitive motion problems
Repetitive motion problems often appear as a numbness or tingling sensation accompanied by pain and the loss of gripping power in your hands
Hand Protection
Elimination or Control of Hazards
Engineering Controls Machine guards
Procedures Lock out/Tag out
Housekeeping and Hygiene Poorly maintained
machinery, tools, sloppy work areas, and cluttered aisles all contribute to hand injuries
Hand Protection
Proper Fit and Use of PPE Select and use the right kind of glove for the
job you are going to be performing Check fit, always use correct sizeMake sure chemical resistant to chemical being used
Inspect your gloves before you use them Remove any rings, watches, or bracelets that might
cut or tear your gloves Look for holes and cracks
that might leak Replace gloves that are
worn or torn
Hand Protection Never wear gloves around powered
rotating equipment - drills, lathes, etc
Hand ProtectionTypes of Hand PPE GLOVES
Metal Mesh Gloves
Leather Gloves
Vinyl and Neoprene Gloves
Rubber Gloves
Padded Cloth Gloves
Heat Resistant Gloves
Latex Disposable Gloves
Lead Line Gloves FOREARM CUFFS THUMB GUARDS AND FINGER COTS MITTENS HAND PADS
Hand Protection
Metal mesh gloves ○ resist sharp
edges and prevent cuts
Hand Protection
Leather gloves ○shield your
hands from rough surfaces
Hand Protection
Vinyl and neoprene gloves ○ protect your
hands against toxic chemicals
Hand Protection
Rubber gloves ○ protect you
when working around electricity
Hand Protection
Padded cloth gloves ○ protect your
hands from sharp edges, silvers, dirt, and vibration.
Hand Protection
Heat resistant gloves ○ protect your
hands from heat and flames
Hand Protection
Latex disposable gloves ○ used to protect
your hands from germs and bacteria
Hand Protection
Lead-lined gloves○ used to protect
your hands from radiation sources
Hand Protection
Forearm Cuffs used to protect your forearm
Thumb Guards and Finger Cots protect only your thumb or
fingers Mittens
protect your hands while working around very cold or hot materials
Hand Pads Hand pads protect your
hands while working around very hot materials
ARM PROTECTION
GAUNTLETS – gloves, w/c are closed-fittings to the hands
Gauntlets for workers handling corrosive substances, such as acids and caustics, shall be made of natural rubber, synthetic rubber or pliable plastic material resistant to corrosion.
Gauntlets for protecting workers against the action of toxic, irritating or infectious substances shall:
(1) cover the forearm as much as possible,
(2) have a close fit at the upper end and
(3) not have the slightest break. Gloves torn during use shall be replaced immediately
Safety Belts, Life Lines and Safety Nets
1) Workmen working in unguarded surface above open pits or tanks, steep slopes, moving machinery and similar locations, or working from unguarded surfaces six (6) meters (20 ft.) or more above water or ground, temporary or permanent floor platform, scaffold construction or where otherwise exposed to the possibility of falls hazardous to life or limb, shall be secured by safety belts and life lines. In situations where safety belts and life lines in guarded platforms and scaffolds or temporary floors are not feasible, safety nets shall be provided and installed.
2) Window washers or cleaners working outside buildings six (6) meters (20 ft.) or more above the ground or other surfaces unless protected from falling by other means, shall use safety belts attached to suitable anchors.
3.) Workmen entering a sewer, flue, duct, or other similarly confined places shall be provided and required to wear safety belts with life lines attached and held by another person stationed at the opening ready to respond to agreed signals.
4.) Workers who are required to climb and work on top of poles six (6) meters or more shall use safety belts. On top of structures where there is no place to strap a safety belt, a messenger line shall be installed for strapping the safety belt or life line.
(1) Safety belts shall be made of chromed tanned leather, linen or cotton webbing, or other suitable materials at least 11.5 cm. (4 1/2 in.) wide and 0.65 cm. (1/4 in.) thick and of sufficient strength to support a weight of 114 kgs. (250 lbs.) without breaking.
(2) Hardware used for safety belts should have a strength of approximately equal to the full strength of the waist band. Buckles shall hold securely without slippage or other failure. This holding power should be achieved by only a single insertion of the strap through the buckle in the normal or usual way.
(3) Belt anchors shall be made of metal machined from bar stock, forged or heat treated, capable of supporting a pull of 2730 kgs. (6,000 lbs.) without fracture applied in the direction which the anchor must withstand should a man fall. All anchors and fastenings shall be provided with means to prevent turning, backing off or becoming loose. Anchor fittings with single thread section which is merely screwed into reinforcing plates shall not be used. Metals recommended for belt anchors are nickel copper alloy and stainless steel.
(4) Life lines shall be made of good quality manila rope of at least 1.9 cm. (3/4 in.) diameter or equivalent material such as nylon rope of at least 1.27 cm. (1/2 in.) diameter and shall be of sufficient strength to support a weight of 1140 kgs. (2,500 lbs.) without breaking.
(5) Safety nets shall not be less than 0.94 cm. (3/8 in.) diameter mesh ropes and not less than 1.90 cm.(3/4 in.) diameter border ropes (perimeter) made of manila rope or other materials that can absorb the impact of a falling body equally as nets fabricated from manila rope of the dimensions specified. The mesh shall be arranged not to exceed 15.25 cm. (6 in.) on canters positively and securely attached to avoid wear at each crossing point and at points of contact with the border.
(6) Safety nets shall be equipped with adequately padded thimbler sockets or equivalent means of attachments. Supports and anchorages shall be of sufficient size and strength to catch any falling worker. The nets shall be attached to sufficient supports outside and beyond the area of possible fall and supported at sufficient heights to prevent sagging to any solid object beneath when cushioning the fall of a worker.
(7) Safety belts, life lines and safety nets shall be inspected before use and at least once each week thereafter. Defective belts, lines or nets shall be immediately discarded and replaced or repaired before reuse.
Foot Protection
Why is Foot Protection Important?
The human foot is rigid enough to support the weight of your entire body, and yet flexible enough to allow you to run, dance, play sports, and to take you anywhere you want to go. Without your feet and toes, your ability to work at your job would be greatly reduced.
Foot Protection
Types of Foot Hazards Impact Injuries Injuries from Spills and Splashes Compression Injuries Electrical Shocks Extremes in Cold, Heat, and Moisture Slipping
Foot ProtectionPotential Incidences of
Foot Hazards Impact Injuries
At work, heavy objects can fall on your feet. If you work around sharp objects, you can step on something sharp and puncture your foot
FOOT PROTECTION
Injuries from Spills and Splashes Liquids such as
acids, caustics, and molten metals can spill into your shoes and boots. These hazardous materials can cause chemical and heat burns
Foot ProtectionPotential Incidences of
Foot Hazards Compression Injuries
Heavy machinery, equipment, and other objects can roll over your feet. The result of these types of accidents is often broken or crushed bones
FOOT PROTECTION
Electrical Shocks Accidents
involving electricity can cause severe shocks and burns
Foot ProtectionPotential Incidences of
Foot Hazards Extremes in Cold,
Heat, and Moisture If not protected, your
feet can suffer from frostbite if you must work in an extremely cold environment. Extreme heat, on the other hand, can blister and burn your feet. Finally, extreme moisture in your shoes or boots can lead to fungal infections
FOOT PROTECTION
Slipping Oil, water,
soaps, wax, and other chemicals can cause you to slip and fall
Foot Protection
Elimination or Control of Hazards
Housekeeping Poorly maintained
machinery, tools, sloppy work areas, and cluttered aisles all contribute to foot injuries
SignsIdentify temporary slip/trip
areas
Foot ProtectionProper Fit and Use of PPE Select and use the right kind of
footwear for the job you are going to be performing. Footwear should meet or exceed the standards set by ANSI (ANSI Z41-1991) Proper fit Correct protection for job task
Inspect your footwear before you use them Look for holes and cracks that might
leak Replace footwear that are worn or
torn When working with chemicals
hose your footwear with water to rinse away any chemicals or dirt before removing your footwear
Store footwear in a clean, cool, dry, ventilated area
Foot ProtectionTYPES OF FOOT PPE
Safety Shoes and Boots○ Steel Toe Footwear○ Metatarsal Footwear○ Reinforced Sole Footwear○ Latex/Rubber Footwear○ PVC Footwear○ Butyl Footwear○ Vinyl Footwear○ Nitrile Footwear○ Electrostatic Dissipating Footwear○ Electrical Hazard Footwear○ Disposable Footwear
Foot Protection Safety Shoes
and Boots
1) Steel toe footwear
○ protects your toes from falling objects and from being crushed
Foot Protection
Metatarsal footwear ○ special guards
that run from your ankle to your toes and protect your entire foot
Foot Protection
Reinforced sole footwear ○ metal
reinforcement that protects your foot from punctures
Foot Protection
Latex/Rubber footwear
○ resists chemicals and provides extra traction on slippery surfaces
Foot Protection Safety Shoes and
Boots
PVC footwear ○ protects your
feet against moisture and improves traction
Foot Protection
Butyl footwear ○ protects against
most ketones, aldehydes, alcohols, acids, salts, and alkalies
Foot Protection
Vinyl footwear ○ resists solvents,
acids, alkalies, salts, water, grease, and blood
Foot Protection
Nitrile footwear ○ resists animal
fats, oils, and chemicals
Foot Protection
Safety Shoes and Boots
Electrostatic dissipating footwear ○ conducts static
electricity to floors that are grounded
Foot Protection
Electrical hazard footwear ○ insulated with
tough rubber to prevent shocks and burns from electricity
Foot Protection
Disposable footwear ○ includes shower
slippers, clear polyethylene and non-woven booties used in dust free work areas
Foot Protection Employee ran over
foot with lawn mowerNotice the damage to
the shoeThe steel toe insert is
lying in the grass next to perfectly fine toes
This employee received no injuries during this incident
Body Protection
Why is Body Protection Important? The skin acts as a natural barrier to the elements Chemicals can break down the skin barrier and
allow secondary infections to manifest
Body Protection
TYPES OF BODY HAZARDS Temperature stress Chemical Contact Radiation
Body Protection
Potential Incidences of Body Hazards Temperature stress
Exposure to heat (hot metals) or cold (dry ice) which results in burns
Chemical ContactChemical splashContact with potentially infectious materials
Radiation
Body Protection
Elimination or Control of Hazards Signage
Communication of hot/cold or radiation Physical Barriers
Metal shielding or cement barrierSplash guards on chemical hoodsClosed chemical systems
Body ProtectionProper Fit and Use of PPE Select and use the
right kind of body protection for the job you are going to be performing Make sure chemical
resistant to what working with
Inspect your aprons/body shields before you use them
Store body protection in a clean, cool, dry, ventilated area
Body Protection
Types of Body PPE Insulated Coats and Pants
Fire resistantHeat resistantCold resistant
Sleeves and ApronsWork well when pouring or manipulating
chemical to reduce splashMake sure the sleeves and aprons are
appropriate for the chemical
Body Protection
Types of Body Protection Coveralls
Tyvek use for particulate filtering such as asbestos
Chemical rated Full body suit
Hazardous materials handling
Carbon filtering for emergency response
Body Protection
THANK YOU!!!!!
Etcoy, Leny A.Lleva, Criselle O..
Muyna, Diana Rose L.
Top Related