1
HVS Program update: GPGRT and CSIR
Louw du Plessis
HVSIA 31 Aug - 2 Sept 2015
2
Contents
• HVS related progress • SIM feedback • Manual Visual Condition Index vs automatic data capturing with
instrumented vehicles
3
HVS feedback
5
Manual Visual Condition Index vs automatic data capturing with instrumented vehicles
• Brief description of how Visual Condition Index (VCI) is measured and calculated (surfaced Pavements)
• Brief description of how Overall Condition Index (OCI) is measured and calculated
• GPDRT VCI data (2010) • Sample of SANRAL OCI data (2013) • Evaluation of differences
7
Measure all visual distress and rate it on a scale of 1 to 5 in terms of degree and extent (structural and functional properties)
• Surfacing defects examples – Spalling of reseal or overlays around cracks (spalling is defined
as the crumbling away of surfacing material around cracks); – Localised loss of surfacing owing to poor bonding with the
underlying layer; – Disintegration of weak aggregates; and – Distress owing to salt damage to the surfacing.
• Structural failures • Functional failures
12
Structural properties
– Structural Cracking – Pumping – Deformation:
• Rutting • Undulation/Settlement
– Patching – Failures / potholes
17
Functional properties
• Riding Quality – potholes/failures; – Patching; – undulations; – corrugation; and – general unevenness.
18
Functional properties
• Skid Resistance – Bleeding – Polished aggregates – Drainage
• Untraveled way – Shoulder erosion – Level differences – Shoulder slope (too steep) – etc.
21
Field Assessment Form
22
Field Assessment Form
23
Data analysis: TMH 22
24
Calculation of VCI for flexible paved roads
The calculation of the visual condition index requires the selection of a weighting factor for each type of distress. The formulae for calculating the VCI are given in equations below.
25
Get this from the field form
Get this from the field form
27
Factor C
28
Calculation of VCI for flexible paved roads
Ratio of the current condition over the worst condition
29
Example
If current condition Σ Fn = 40 and worst condition Σ Fn = 50, then VCI = 100 ( 1 – 0.02 x 40) = 20 (bad) If current condition Σ Fn = 10(good) and worst condition Σ Fn = 50, then VCI = 100 ( 1 – 0.02 x 10) = 80 (Good)
30
Conversion required to get VCI to a % scale
VCI calculations (GPDRT 2010 data set)
32
Overall Condition Index (OCI) from automated data capturing using instrumented vehicles
• OVI is a function of: – Riding quality – Rut depth – Surface texture – Structural Stiffness Index – Crack Index (Formula developed in-house by SANRAL. Not in any TMH or TRH yet)
34
OCI calculated for each 100m of road network measured
• OCI = a*IRI + b*RUT + c*Text + d*SSI + e*Crack – IRI: International Roughness index value – Rut: Rut depth Index value – Text: Macro Texture Index value – SSI: Structural Stiffness Index value calculated from FWD
data – Crack: Crack index
All parameters are measured by SANRAL’s automated vehicle except SSI
35
a – e: weight coefficients
SSI is determined through FWD testing
37
Ymax & BLI
• Determined from FWD testing: – Ymax: max deflection under FWD load plate (d0) – BLI = Deflection originating from the base layer
calculated as: d0 – d300 • D300 is the deflection measured by the sensor placed
300mm away from the dropping load plate
FALLING WEIGHT DEFLECTOMETER (FWD): Ymax & BLI
d0
BLI = d0 - d300
300mm
d300
Ymax
39
FWD output example
d0 d300 BLI = d0 - d300
40
Structural Stiffness Index (SSI) (TRH 22 – 1994)
,
X = Lymax, LBLI
The Pavement base coarse types comes from the Province material data base. Is there an existing one? Can we assume that all surfaced roads have Granular base coarse material?
• E = ADT x % heavy Veh x # 80s/ heavy Veh
Issues: ADT per lane 12h counts convert to ADT, How many E80s/ truck (I used 2)
• We get this from looking at the traffic growth over a period (Use growth over the last 5 years ?) (for my examples I used 3%)
We get this from Traffic volume counts
44
Final SSI
• The final SSI value is the average of the SSI values determined from Ymax and BLI measurements
45
46
Summary SSI flow diagram
LINEAR_ SECTIODIRECTPROVIOWNER BEGIN_DIST END_DIST LANE IRI RUT TEXT SSI OCID025 1 N 5 PROV 0.00000 0.10000 1 0.00000 0.80922 1.00000 0.75000 59.27665 D025 1 N 5 PROV 0.10000 0.20000 1 0.73724 0.88945 0.34918 0.75000 70.78459 D025 1 N 5 PROV 0.20000 0.30000 1 0.96009 0.87968 0.88341 0.75000 87.86147 D025 1 N 5 PROV 0.30000 0.40000 1 0.87397 0.88770 0.76308 0.75000 83.11162 D025 1 N 5 PROV 0.40000 0.50000 1 0.83741 0.90765 0.63816 0.75000 80.11485 D025 1 N 5 PROV 0.50000 0.60000 1 0.89718 0.86642 1.00000 0.75000 87.90790 D025 1 N 5 PROV 0.60000 0.70000 1 0.83368 0.82955 1.00000 0.75000 84.89697 D025 1 N 5 PROV 0.70000 0.80000 1 0.70813 0.85487 1.00000 0.75000 81.88998 D025 1 N 5 PROV 0.80000 0.90000 1 0.48301 0.83496 1.00000 0.75000 74.53885 D025 1 N 5 PROV 0.90000 1.00000 1 0.81106 0.81339 1.00000 0.75000 83.73361 D025 1 N 5 PROV 1.00000 1.10000 1 0.84223 0.86696 1.00000 0.75000 86.27570 D025 1 N 5 PROV 1.10000 1.20000 1 0.65913 0.87527 1.00000 0.75000 81.03214 D025 1 N 5 PROV 1.20000 1.30000 1 0.73467 0.78907 1.00000 0.75000 80.71220 D025 1 N 5 PROV 1.30000 1.40000 1 0.77255 0.77736 1.00000 0.75000 81.49735 D025 1 N 5 PROV 1.40000 1.50000 1 0.78079 0.82270 1.00000 0.75000 83.10464 D025 1 N 5 PROV 1.50000 1.60000 1 0.61679 0.81359 1.00000 0.75000 77.91150 D025 1 N 5 PROV 1.60000 1.70000 1 0.86757 0.84208 1.00000 0.75000 86.28922 D025 1 N 5 PROV 1.70000 1.80000 1 0.87942 0.84611 1.00000 0.75000 86.76569 D025 1 N 5 PROV 1.80000 1.90000 1 0.57362 0.87830 1.00000 0.75000 78.55753 D025 1 N 5 PROV 1.90000 2.00000 1 0.80492 0.87230 1.00000 0.75000 85.31668 D025 1 N 5 PROV 2.00000 2.10000 1 0.92578 0.86768 1.00000 0.75000 88.80385 D025 1 N 5 PROV 2.10000 2.20000 1 0.75975 0.82067 1.00000 0.75000 82.41242 D025 1 N 5 PROV 2.20000 2.30000 1 0.89461 0.85204 1.00000 0.75000 87.39960
Example of data from SANRAL (2013)
48
Comparisons: Road K175
49
Comparisons: Road K175
Traffic 2013:
K175:Hand 2013 12h: 7 297 22% Sec 1
106 29% Sec 21 970 22% Sec 35 178 20% Sec 4
ADT current % Heavies #80s/ Heavy # lanes Equiv daily E80sConveted to ADTHand 2013 24h: 10 946 22 2 1 4816 Sec 1
159 29 2 1 92 Sec 22 955 22 2 1 1300 Sec 33 910 20.00 2 1 1564 Sec 4
50
K175: FWD data
K175 1 A 0.071 0.2 0.271 569.65 385K175 1 A 0.271 0.201 0.472 413.1 161.65K175 1 A 0.472 0.2 0.672 479.2 288.1K175 1 A 0.672 0.199 0.871 461.2 267.15K175 1 A 0.871 0.201 1.072 707.35 471.45K175 1 A 1.072 0.199 1.271 733.25 471.85K175 1 A 1.271 0.201 1.472 590.55 367.85K175 1 A 1.472 0.199 1.671 485.75 306.05K175 1 A 1.671 0.2 1.871 666.35 442.15K175 1 A 1.871 0.2 2.071 564.4 387.85K175 1 A 2.071 0.201 2.272 536.2 288.05K175 1 A 2.272 0.199 2.471 600 397.45K175 1 A 2.471 0.201 2.672 433.95 262.2K175 1 A 2.672 0.2 2.872 266.15 158.3K175 1 A 2.872 0.2 3.072 487.35 331.6K175 1 A 3.072 0.2 3.272 468.2 311.95K175 1 A 3.272 0.2 3.472 617.4 400.35K175 1 A 3.472 0.199 3.671 347.65 227.7
Linear_IDSection_I
DDirection
Starting_Distance
Distance_between_drops
Up_to_Distance
Average_Y_Max
Average_BLI
Weak
Strong
52
K175: Results: OCI vs VCI
K175Sec 1 OCI VCI
2010Mean 62 84 Cat Road
0.95 69 A0.90 69 B0.80 67 C
Sec 2Mean 69 85 Cat Road
0.95 74 A0.90 73 B0.80 72 C
Sec 3Mean 56 55 Cat Road
0.95 77 A0.90 71 B0.80 63 C
Sec 4Mean 65 77 Cat Road
0.950 76 A0.900 74 B0.800 71 C
53
D25
54
D25Sec 1 OCI VCI
2010Mean 72 78 Cat Road
95% 77 A90% 76 B80% 75 C
Sec 2Mean 65 91 Cat Road
95% 75 A90% 75 B80% 69 C
Sec 3Mean 65 87 Cat Road
0.95 71 A0.9 70 B0.8 69 C
D30Sec 1 OCI VCI
2010Mean 44.6 68 Cat Road
ABC
Sec 2 Cat RoadMean 55 47 A
0.95 68 B0.9 64 C0.8 62
55
Comparison
0
10
20
30
40
50
60
70
80
90
100
0 10 20 30 40 50 60 70 80 90 100
Visu
al C
ondi
tion
Inde
x
Overall Condition Index
VCI vs OCI
62
69
56
65
72
65
65
45
55
K175
D25
D30
56
Why should we calculate both VCI and OCI ?
• They measure different properties and are not directly related to each other. • For instance with the FWD we measure the structural capacity of a
pavement (remaining life) something we cannot measure with visual surveys only.
• Example:
– If a fog spray is applied to an old pavement surface and new line markings, the VCI can increase from below 60 to above 80.
– Using the OCI method the application of a fog spay (covering the surface distress) will not mask the problem and will have no impact on the OCI values
57
Thank you
Top Related