7/22/2019 HUAWEI QUIDWAY R2600
1/134
HUAWEI
Quidway R2600/3600 Series Modular Routers
Installation Manual
V200R001
7/22/2019 HUAWEI QUIDWAY R2600
2/134
Quidway R2600/3600 Series Modular Routers
Installation Manual
Manual Version T2-080430-20020202-C-1.0
Product Version V200R001
BOM 31040430
Copyright 2001 by Huawei Technologies Co., Ltd.
All Rights Reserved
No part of this document may be reproduced or transmitted in any form or by anymeans without prior written consent of Huawei Technologies Co., Ltd.
Trademarks
, HUAWEI, C&C08, EAST8000, HONET, ViewPoint, INtess, ETS, DMC, SBS,
TELLIN, InfoLink, Netkey, Quidway, SYNLOCK, Radium, , M900/M1800,TELESIGHT, Quidview, NETENGINE, Musa, OptiX, Airbridge, Tellwin, Inmedia,
VRP, DOPRA, iTELLIN are trademarks of Huawei Technologies Co., Ltd.
Notice
The information in this document is subject to change without notice. Althoughevery effort has been made to make this document as accurate, complete, andclear as possible, Huawei Technologies assumes no responsibility for any errorsthat may appear in this document.
Huawei Technologies Co., Ltd.
Address: Huawei Customer Service Building, Kefa Road, Science-basedIndustrial Park, Shenzhen, P. R. China
Zip code: 518057
Tel: +86-755-6540036
Fax: +86-755-6540035
Website: http://www.huawei.com
E-mail: [email protected]
7/22/2019 HUAWEI QUIDWAY R2600
3/134
About This Manual
Contents
The manual consists of 8 chapters that brief the appearance, features, installation,configuration, maintenance, troubleshooting and function modules of Quidway
R2600/3600 Series Modular Routers.
Chapter 1 is a brief introduction of the Quidway R2600/3600 series modularrouters.
Chapter 2 describes the appearance and system features of Quidway
R2620/R2621, R2630/R2630E, R2631/R2631E, R3640/R3640E andR3680/R3680E.
Chapter 3 introduces the installation preparations of the routers.
Chapter 4 introduces in detail the installation procedures of the routers.
Chapter 5 is about the startup and configuration of the routers.
Chapter 6 covers the software and hardware maintenance.
Chapter 7 is the troubleshooting procedures during installation.
Chapter 8 depicts the function modules of the routers.
Target Readers
The manual is intended for the following readers:
Installation engineers & technicians
Operation & maintenance personnel
7/22/2019 HUAWEI QUIDWAY R2600
4/134
Conventions Used in the Document
Keyboard operation
Format Description
Press the key with key name expressed with a pointedbracket, e.g. ,,,or.
Press the keys concurrently; e.g. means thethree keys should be pressed concurrently.
Press the keys in turn, e.g. means the two keysshould be pressed in turn.
[Menu Option] The item with a square bracket indicates the menu option,
e.g.[System]option on the main menu. The item with apointed bracket indicates the functional button option, e.g.button on some interface.
[Menu 1/Menu 2/Menu 3] Multi-level menu options, e.g. [System/Option/Color setup]on the main menu indicates[Color Setup]on the menuoption of[Option], which is on the menu option of[System].
Mouse operation
Action Description
Click Press the left button or right button quickly (left button bydefault).
Double Click Press the left button twice continuously and quickly.
Drag Press and hold the left button and drag it to a certain position.
Symbol
Some distinct symbols are employed in the manual to indicate the special notice thatshould be taken for the operation. The symbols are:
Caution, Notice, Warning, Danger:Notify the special attention that should begiven to the operation.
Note, Prompt, Tip, Thought: Give further necessary supplement or explanationfor the operation description.
7/22/2019 HUAWEI QUIDWAY R2600
5/134
Installation ManualQuidway R2600/3600 Series Modular Routers Table of Contents
i
Table of Contents
Chapter 1 Introduction................................................................................................................. 1-1
1.1 Quidway R2600/3600 Series Modular Routers ................................................................ 1-1
1.2 Models .............................................................................................................................. 1-1
1.3 Function Modules Supported............................................................................................ 1-1
1.4 Product Features .............................................................................................................. 1-2
1.5 Typical Application ............................................................................................................ 1-3
Chapter 2 Appearance and System Features............................................................................ 2-1
2.1 Quidway R2620/R2621..................................................................................................... 2-1
2.1.1 Appearance ............................................................................................................ 2-1
2.1.2 Indicators on Panel ................................................................................................ 2-2
2.1.3 System Description ................................................................................................ 2-2
2.2 Quidway R2630/R2630E .................................................................................................. 2-3
2.2.1 Appearance ............................................................................................................ 2-3
2.2.2 Indicators on Panel ................................................................................................ 2-3
2.2.3 System Description ................................................................................................ 2-4
2.3 Quidway R2631/R2631E .................................................................................................. 2-5
2.3.1 Appearance ............................................................................................................ 2-5
2.3.2 Indicators on Panels............................................................................................... 2-52.3.3 System Description ................................................................................................ 2-6
2.4 Quidway R3640/R3640E .................................................................................................. 2-6
2.4.1 Appearance ............................................................................................................ 2-6
2.4.2 Indicators on Panel ................................................................................................ 2-7
2.4.3 System Description ................................................................................................ 2-7
2.5 Quidway R3680/R3680E .................................................................................................. 2-8
2.5.1 Appearance ............................................................................................................ 2-8
2.5.2 Indicators on Panel ................................................................................................ 2-9
2.5.3 System Description ................................................................................................ 2-9
Chapter 3 Installation Preparations............................................................................................ 3-1
3.1 Safety Recommendations................................................................................................. 3-1
3.2 Installation Conditions....................................................................................................... 3-1
3.2.1 Temperature and Humidity Requirements ............................................................. 3-1
3.2.2 Cleanness Requirements....................................................................................... 3-2
3.2.3 ESD-Preventive Requirements .............................................................................. 3-3
3.2.4 Anti-interference Requirements ............................................................................. 3-3
3.2.5 Lightning Protection Requirements ........................................................................ 3-3
3.2.6 Workbench Requirements...................................................................................... 3-4
3.3 Tools and Devices Required............................................................................................. 3-4
7/22/2019 HUAWEI QUIDWAY R2600
6/134
7/22/2019 HUAWEI QUIDWAY R2600
7/134
Installation ManualQuidway R2600/3600 Series Modular Routers Table of Contents
iii
8.3 Function Modules Installation ........................................................................................... 8-3
8.4 Function Modules Troubleshooting................................................................................... 8-5
8.5 1FE/2FE Module............................................................................................................... 8-5
8.5.1 Introduction............................................................................................................. 8-58.5.2 Appearance ............................................................................................................ 8-6
8.5.3 Interface Attributes ................................................................................................. 8-7
8.5.4 Indicators on Panel ................................................................................................ 8-7
8.5.5 Interface Cable....................................................................................................... 8-8
8.5.6 Connecting Interface Cable.................................................................................. 8-10
8.6 2SA/4SA Module............................................................................................................. 8-11
8.6.1 Introduction........................................................................................................... 8-11
8.6.2 Appearance .......................................................................................................... 8-13
8.6.3 Interface Attributes ............................................................................................... 8-14
8.6.4 Indicators on Panel .............................................................................................. 8-15
8.6.5 Interface Cable..................................................................................................... 8-16
8.6.6 Connecting Interface Cable.................................................................................. 8-22
8.7 8AS/16AS Module........................................................................................................... 8-24
8.7.1 Introduction........................................................................................................... 8-24
8.7.2 Appearance .......................................................................................................... 8-25
8.7.3 Interface Attributes ............................................................................................... 8-25
8.7.4 Indicators on Panel .............................................................................................. 8-26
8.7.5 Interface Cable..................................................................................................... 8-27
8.7.6 Connecting Interface Cable.................................................................................. 8-32
8.8 1E1/2E1/4E1 Module...................................................................................................... 8-33
8.8.1 Introduction........................................................................................................... 8-33
8.8.2 Appearance .......................................................................................................... 8-34
8.8.3 Interface Attributes ............................................................................................... 8-35
8.8.4 Indicators on Panel .............................................................................................. 8-36
8.8.5 Interface Cable..................................................................................................... 8-37
8.8.6 Internal DIP Switches........................................................................................... 8-39
8.8.7 Connecting Interface Cable.................................................................................. 8-41
8.9 4BS Module .................................................................................................................... 8-43
8.9.1 Introduction........................................................................................................... 8-43
8.9.2 Appearance .......................................................................................................... 8-43
8.9.3 Interface Attributes ............................................................................................... 8-44
8.9.4 Indicators on Panel .............................................................................................. 8-45
8.9.5 Interface Cable..................................................................................................... 8-46
8.9.6 Connecting Interface Cable.................................................................................. 8-46
8.10 2S1B Module ................................................................................................................ 8-46
8.10.1 Introduction......................................................................................................... 8-46
8.10.2 Appearance ........................................................................................................ 8-47
8.10.3 Interface Attributes ............................................................................................. 8-47
7/22/2019 HUAWEI QUIDWAY R2600
8/134
Installation ManualQuidway R2600/3600 Series Modular Routers Table of Contents
iv
8.10.4 Indicators on Panel ............................................................................................ 8-48
8.10.5 Interface Cable................................................................................................... 8-48
8.10.6 Connecting Interface Cable................................................................................ 8-49
8.11 2FXS/2FXO/2E&M Module........................................................................................... 8-508.11.1 Introduction......................................................................................................... 8-51
8.11.2 Appearance ........................................................................................................ 8-51
8.11.3 Interface Attributes ............................................................................................. 8-51
8.11.4 Indicators on Panel ............................................................................................ 8-52
8.11.5 Interface Cable................................................................................................... 8-53
8.11.6 Connecting Interface Cable................................................................................ 8-55
8.12 4FXS/4FXO/4E&M Module........................................................................................... 8-56
8.12.1 Introduction......................................................................................................... 8-56
8.12.2 Appearance ........................................................................................................ 8-56
8.12.3 Interface Attributes ............................................................................................. 8-57
8.12.4 Indicators on Panel ............................................................................................ 8-57
8.12.5 Interface Cable................................................................................................... 8-58
8.12.6 Connecting Interface Cable................................................................................ 8-58
8.13 8LSA Module ................................................................................................................ 8-59
8.13.1 Introduction......................................................................................................... 8-59
8.13.2 Appearance ........................................................................................................ 8-60
8.13.3 Interface Attributes ............................................................................................. 8-60
8.13.4 Indicators on Panel ............................................................................................ 8-61
8.13.5 Interface Cable................................................................................................... 8-61
8.13.6 Connecting Interface Cable................................................................................ 8-66
8.14 E1VI Module ................................................................................................................. 8-67
8.14.1 Introduction......................................................................................................... 8-67
8.14.2 Appearance ........................................................................................................ 8-67
8.14.3 Interface Attributes ............................................................................................. 8-67
8.14.4 Indicators on Panel ............................................................................................ 8-68
8.14.5 Interface Cable................................................................................................... 8-68
8.14.6 Connecting Interface Cable................................................................................ 8-70
7/22/2019 HUAWEI QUIDWAY R2600
9/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 1Introduction
1-1
Chapter 1 Introduction
1.1 Quidway R2600/3600 Series Modular Routers
Quidway R2600/3600 series modular routers (referred to as R2600/3600 serieshereafter) are independently developed by Huawei for enterprise networks. They canbe used as core routers in medium- and small-sized Intranets, or as access servers atsome major branch offices.
With a modular structure, R2600/3600 series adopt the Versatile Routing Platform(VRP), a proprietary software platform of Huawei, and incorporate high-performanceprocessor, bus technology and fast routing policy. While providing a large array of
service interfaces, it can also be used together with QuidwayR1600 series, QuidwayR2500 series, and Quidway NetEngine08/16E series routers to provide overallsolutions for large- and medium-sized industry users such as telecom, private networkcarrier, ISP, finance, tax, police, and railway, etc. At the same time, its function modulescomply with various network standards. So R2600/3600 series are in the best intereststo protect your existing investments while guaranteeing interoperability at variouslevels with major products on the global market.
1.2 Models
R2600/3600 series include: R2620, R2621, R2630, R2631, R3640, R3680, R2630E,R2631E, R3640E and R3680E:
R2620 and R2621 adopt Power PC 8240 CPU main board, but they differ fromother R2600/3600 series routers in that they have two fixed synchronous serialinterfaces besides the fixed Ethernet interfaces.
R2630E, R2631E, R3640E and R3680E differ from R2630, R2631, R3640 andR3680 in that the former adopt Power PC 8240 CPU main board and the latteradopt Pentium CPU main board. They have the same software features andfunctional implementations. The interface modules used by them are completelycompatible, but the former are more powerful in their processing capability andpacket forwarding performance.
R2600/3600 series provide different number of module slots:
Quidway R2620 provides one 10/100Mbps Ethernet interfaces, two synchronous
serial interfaces, and two standard PCI slots. Quidway R2621 provides two 10/100Mbps Ethernet interface, two synchronousserial interfaces and two standard PCI slots.
Quidway R2630/R2630E provides one 10/100Mbps Fast Ethernet interface andthree standard PCI slots.
Quidway R2631/R2631E provides two 10/100Mbps Fast Ethernet interfaces andthree standard PCI slots.
Quidway R3640/R3640E provides four standard PCI slots. Quidway R3680/R3680E provides eight standard PCI slots.
1.3 Function Modules Supported
R2600/3600 series support the following function modules:
7/22/2019 HUAWEI QUIDWAY R2600
10/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 1Introduction
1-2
1-port 10/100Base-TX Fast Ethernet interface module (1FE)
2-port 10/100Base-TX Fast Ethernet interface module (2FE) 2-port high-speed sync/async serial interface module (2SA) 4-port high-speed sync/async serial interface module (4SA)
2-port sync/async serial interface+1 port ISDN BRI S/T interface module (2S1B) 1-port channelized cE1/PRI interface module (1E1) 2-port channelized cE1/PRI interface module (2E1)
4-port channelized cE1/PRI interface module (4E1) 4-port ISDN BRI S/T interface module (4BS) 8-port async serial interface module (8AS) 16-port async serial interface module (16AS) 2-port voice interface module (FXS interface) (2FXS) 2-port voice interface module (FXO interface) (2FXO)
2-port voice interface module (E&M interface) (2E&M) 4-port voice interface module (FXS interface) (4FXS) 4-port voice interface module (FXO interface) (4FXO) 4-port voice interface module (E&M interface) (4E&M)
8-port low-speed sync/async serial interface module ( 8LSA) 1-port voice interface module (E1 interface) (E1VI)
When buying the R2600/3600 series, you can select proper function modules based onyour requirements, following the selection rules below:
Multiple modules of the same type can be configured in the router. The module can be configured to any slot. The interface cable is directly related with specific module.
For details about the function modules and interface cables, please refer to Chapter 8
Function Modules.
1.4 Product Features
I. Powerful backup function
R2600/3600 series support interface backup, link backup and route backup functions,of which the backup can be between DDN line and dialup line, between DDN line andvirtual link, or between dialup lines. It supports mutual backup between such networksas DDN, X.25, PSTN, ISDN, and frame relay. It also supports HSRP, and two routerscan be backup for each other.
II. Solution to remote office
R2600/3600 series provide solution to high-density remote office. It supports a
maximum of 112 analog dialup users (R3680/R3680E) or 28 ISDN BRI dialup users(R3680/3680E).
III. E1/cE1 and cE1/PRI compatible
R2600/3600 series provide cE1 (Channelized E1) access, and the cE1 interface iscompatible with the E1 interface. At the same time, the ISDN PRI function can be
implemented on the cE1 interface.
IV. High density interfaces
R2600/3600 series support up to 28 2Mbit/s sync serial interface (R3680/R3680E),
which can connect to such networks as DDN, frame relay, and X.25.
7/22/2019 HUAWEI QUIDWAY R2600
11/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 1Introduction
1-3
V. Voice-related support features
R2600/3600 series support voice features. It can provide the following voice moduletypes for different users: 2FXS, 2FXO, 2E&M, 4FXS, 4FXO, 4E&M and E1VI, among
which: 2FXS and 4FXS modules are used to connect analog phones. 2FXO and 4FXO modules are used to connect loop trunks in the switching system. 2E&M and 4E&M modules are used for the connection of E&M trunks in the
switching system. E1VI module is used for the connection of E1 trunks in the switching system.
The voice modules of R2600/3600 series support multiple coding algorithms such asG.711, G.723 and G.729. It also supports H.323 protocol stack and GK interface, anddemonstrates successful interoperability with the equipment from such VoIP suppliersas Cisco, AudioCodec, Motorola and VocalTec.
VI. Flexible memory configuration
Users can select the memory capacity flexibly according to system configuration,number of function modules, and performance requirement. Up to 256MB memory is
supported.
VII. Others
R2600/3600 series support 100Mbps fast access to the local network and flexiblenetworking configuration.
1.5 Typical Application
7/22/2019 HUAWEI QUIDWAY R2600
12/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 1Introduction
1-4
Quidway routers enterprise network solutio n
Internet
Phone
AT0/E&M
LAN
DDN/FR
LAN
PBX
Branch Intranet
Branch Intranet
Quidway3680
A8010 Refi ner
LAN
PBX
LAN
ServerGK
FAX
LAN
LAN
Central network
LAN
DDN/FR/ X25
LAN
PSTN/ISDN
Quidway 1602/1603/1604
LAN
DDN/FR/
X25
LAN
PSTN/ISDN
LANLevel-3 Intranet
Level-3 Intranet
ISDN/PSTN
representative office
Quidway2511/2509/4001
The red dotted line stands for backup line.
QuidwayR2600/3600QuidwayR2600/3600
E1 trunk
Figure 1-1 Typical application of Quidway R2600/3600 series routers
7/22/2019 HUAWEI QUIDWAY R2600
13/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 2Appearance and System Features
2-1
Chapter 2 Appearance and System Features
2.1 Quidway R2620/R2621
2.1.1 Appearance
I. Appearance of R2620
The front panel and rear panel of R2620 are shown in the following figures.
SLOT0 SLOT1 WAN0 WAN1 LAN0
POWER
SYSTEMREADYACTIVE
LI NKACTI VE
Figure 2-1 Front panel of R2620
AUX CONSOLEWAN1 WAN0
Figure 2-2 Rear panel of R2620
II. Appearance of R2621
The front panel and rear panel of R2621 are shown in the following figures.
SLOT0 SLOT1 WAN0 WAN1 LAN0 LAN1PO
POWERSYSTEM
READYACTIVE
LINKACTIVE
Figure 2-3 Front panel of R2621
AUX CONSOLEWAN0WAN0WAN1
Figure 2-4 Rear panel of R2621
7/22/2019 HUAWEI QUIDWAY R2600
14/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 2Appearance and System Features
2-2
2.1.2 Indicators on Panel
The meanings of indicators on the front panel of R2620/R2621 are shown in thefollowing table.
Table 2-1 Meanings of indicators on the front panel of R2620/R2621
Indicator Meaning
POWER System power indicator: Off means power is off. On means power is on.
SYSTEMHardware status indicator. Blinking means system is normal. Always on/offmeans system is abnormal.
READYModule indicator. On means the module of the current slot is working normally.Off means the module is abnormal or no module is installed in the current slot.
ACTIVEBlinking means data is being received and transmitted by the module in thecurrent slot. Off means no data is being received or transmitted by the module inthe corresponding slot.
LINK Off means the LAN line is not connected. On means the LAN line is connected.
SLOT0-SLOT1 Indicating the corresponding slot number.WAN0-WAN1 Indicating the corresponding WAN interface number.
LAN0, LAN1 (only for R2621) Indicating the corresponding Ethernet interface number.
The attributes of WAN0 and WAN1 interfaces of R2620/2621 are described in thefollowing table.
Table 2-2 Attributes of WAN0 and WAN1 interfaces of R2620/2621
Att rib ute Synchronous
Connector DB-50
V.24 V.35
Interface standards andoperating mode DTEDCE
DTEDCE
Minimum baud rate (bit/s) 1200 1200
Maximum baud rate (bit/s) 64K 2.048M
Services supported---Modem dial-up---Backup---Terminal access service
Protocols supported
---PPP---MP---LAPB---X.25---HDLC---SDLC---Frame Relay
2.1.3 System Description
The table below shows the basic configurations, dimensions, operating environment,etc. of R2620 and R2621.
7/22/2019 HUAWEI QUIDWAY R2600
15/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 2Appearance and System Features
2-3
Table 2-3 System description of R2620/R2621
Item Description of R2620 Description of R2621
Slot A maximum of 2 function modules can be configured according torequirement.
CPU Power PC 8240 200MHz
BOOT ROM 512KB 512KB
Default: 32MBSDRAM
Max.: 128MB
FLASH 8MB
Dimensions Width x Height x Depth = 440mm x 86mm x 300mm
Weight 5kg
AC: 85V to 264V 50/60HzInput voltage
DC: -40V to -75V
Max. Power 70W
Operating temperature 0 to 40OC
Operating humidity 10 to 90% non-condensing
Note:
Dynamic memory (DRAM/SDRAM) works as main memory.FLASH stores system programs.
2.2 Quidway R2630/R2630E
2.2.1 Appearance
For R2630 and R2630E, their front panels and rear panels are very similar, see theiroutlook as the following (take R2630 as an example).
Figure 2-5 Front panel of R2630
Figure 2-6 Rear panel of R2630
2.2.2 Indicators on Panel
The meanings of indicators on the front and rear panels of R2630/R2630E are shown in
the following tables.
7/22/2019 HUAWEI QUIDWAY R2600
16/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 2Appearance and System Features
2-4
Table 2-4 Meanings of indicators on the front panel of R2630/R2630E
Indicator Meaning
POWER System power indicator: Off means power is off, On means power is on.
SYSTEM Hardware status indicator. Blinking means the system runs normally. Always on/offmeans the system is abnormal.
READYModule status indicator: On means the module in corresponding slot runs normally.Off means the module runs abnormally or no module is installed.
ACTIVEBlinking means data is being received or transmitted by the module in thecorresponding slot. Off means no data is being received or transmitted
0 - 2 Indicating the slot number.
LANEthernet interface indicator: Green means the interface is normal. Blinking yellowmeans data is being received and transmitted over the Ethernet.
Table 2-5 Meanings of indicators on the rear panel of R2630/R2630E
Indicator MeaningLINK Off means the Ethernet link is not connected. On means the link is connected.
ACTIVEOff means no data is being received and transmitted by the Ethernet interface.Blinking means data is being received or transmitted.
2.2.3 System Description
The following table shows the basic configuration, dimensions, operating environment,etc. of R2630 and R2630E.
Table 2-6 System description of R2630/R2630E
Item Description of R2630 Description of R2630E
SlotA maximum of 3 interface modules can be configured according torequirement.
CPU Pentium 133MHz Power PC 8240 200MHz
NVRAM 128KB 128KB
BOOTROM 512KB 512KB
Default: 64MBSDRAM None
Max.: 256MB
Default: 32MBDRAM
Max.: 128MBNone
FLASH 8MB
Dimensions Width x Height x Depth = 440mm x 43mm x 400mm
Weight 8kgAC: 160 to 240V 50/ 60Hz AC: 85 to 264V 50/60Hz
Input voltageDC: -40 to -75V
Max. power 80W
Operating temperature 0 to 40OC
Operating humidity 10 to 90% non-condensing
Note:
Dynamic memory (DRAM/SDRAM) works as main memory.FLASH stores system programs.NVRAM stores configuration files.
7/22/2019 HUAWEI QUIDWAY R2600
17/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 2Appearance and System Features
2-5
2.3 Quidway R2631/R2631E
2.3.1 Appearance
For R2631 and R2631E, their front panels and rear panels are very similar, see theiroutlook as the following (take R2631 as an example).
Figure 2-7 Front panel of R2631
Figure 2-8 Rear panel of R2631
2.3.2 Indicators on Panels
The meanings of indicators on the front and rear panels of R2631 and R2631E areshown in the following tables.
Table 2-7 Meanings of indicators on the front panel of R2631/R2631E
Indicator Meaning
POWER System power indicator: Off means power is off. On means power is on.
SYSTEMHardware status indicator: Blinking means system is normal. Always on/off means thesystem is abnormal.
READYModule status indicator: On means the module runs normally in the current slot. Offmeans the module runs abnormally or no module is installed.
ACTIVEBlinking means data is being received or transmitted by the module in the current slot. Offmeans no data is being received or transmitted by the module in the current slot.
0 - 2 Position of the corresponding slots.
LANEthernet interface indicator. Green means the interface is normal. Blinking yellow meansthat data is being received or transmitted over the Ethernet.
Table 2-8 Meanings of indicators on the rear panel of R2631/R2631E
Indicator Meaning
LINK Off means the Ethernet link is not connected. On means the link is connected.
ACTIVEOff means no data is being received or transmitted by the Ethernet interface. Blinkingmeans data is being received or transmitted.
0 - 1 Corresponding port number.
7/22/2019 HUAWEI QUIDWAY R2600
18/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 2Appearance and System Features
2-6
2.3.3 System Description
The following table shows the basic configuration, dimensions, operating environment,etc. of R2631 and R2631E.
Table 2-9 System description of R2631/R2631E
Item Description of R2631 Description of R2631E
SlotA maximum of 3 interface modules can be configured according torequirement.
CPU Pentium133MHz Power PC 8240 200MHz
NVRAM 128KB
BOOT ROM 512KB
Default: 64MBSDRAM None
Max.: 256MB
Default: 32MBDRAM
Max.: 128MBNone
FLASH 8MBDimensions Width x Height x Depth = 440mm x 43mm x 400mm
Weight 8kg
AC: 160 to 240V 50/ 60Hz AC: 85 to 264V 50/ 60HzInput voltage
DC: -40V to -75V
Max. power (with 3 modules) 80W
Operating temperature 0 to 40OC
Operating humidity 10 to 90% non-condensing
Note:
Dynamic memory (DRAM/SDRAM) works as main memory.
FLASH stores system programs.NVRAM stores configuration files.
2.4 Quidway R3640/R3640E
2.4.1 Appearance
For R3640 and R3640E, their front panels and rear panels are very similar, see their
outlook as the following (take R3640 as an example)
Figure 2-9 Front panel of R3640
7/22/2019 HUAWEI QUIDWAY R2600
19/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 2Appearance and System Features
2-7
Figure 2-10 Rear panel of R3640
2.4.2 Indicators on Panel
The meanings of indicators on the front panel of R3640/R3640E are shown in thefollowing table.
Table 2-10 Meanings of indicators on the front panel of R3640/R3640E
Indicator Meaning
POWER System power indicator: Off means power is off. On means power is on.
SYSTEMHardware status indicator: Blinking means system is normal. Always on/off meanssystem is abnormal.
READYModule indicator. On means the module of the current slot is working normally. Offmeans the module is abnormal or no module is installed in the current slot.
ACTIVEBlinking means data is being received and transmitted by the module in the currentslot. Off means no data is being received or transmitted by the module in the currentslot.
0 - 3 Position of corresponding slots.
2.4.3 System Description
The following table shows the basic configurations, dimensions, operating environment,etc. of R3640 and R3640E.
7/22/2019 HUAWEI QUIDWAY R2600
20/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 2Appearance and System Features
2-8
Table 2-11 System Description of R3640/R3640E
Item Description of R3640 Description of R3640E
Slot A maximum of 4 function modules can be configured according to requirement.Processor Pentium 133MHz Power PC 8240 250MHz
NVRAM 128KB
BOOT ROM 512KB
Default: 128MBSDRAM None
Max.: 256MB
Default: 32MBDRAM
Max.: 128MBNone
FLASH 8MB
Dimensions Width x Height x Depth = 440mm x 43mm x 400mm
Weight 8kg
AC: 160 to 240V 50/60Hz AC: 85 to 264V 50/60HzInput voltage
DC: -40V to -75V
Max. power (with 4 modules) 80W
Operating temperature 0 to 40OCOperating humidity 10 to 90% non-condensing
Note:
Dynamic memory (DRAM/SDRAM) works as main memory.FLASH stores system programs.
NVRAM stores configuration files.
2.5 Quidway R3680/R3680E
2.5.1 Appearance
For R3680 and R3680E, their front panels and rear panels are very similar, see theiroutlook as the following (take R3680 as an example)
Figure 2-11 Front panel of R3680
Figure 2-12 Rear panel of R3680/R3680E
7/22/2019 HUAWEI QUIDWAY R2600
21/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 2Appearance and System Features
2-9
2.5.2 Indicators on Panel
The meanings of indicators on the front panel of R3680/R3680E are shown in thefollowing table.
Table 2-12 Meanings of indicators on the front panel of R3680/R3680E
Indicator Meaning
POWER System power indicator: Off means power is off. On means power is on.
SYSTEMHardware status indicator: Blinking means system is normal. Always on/off meanssystem is abnormal.
READYModule indicator. On means the module of the current slot is working normally. Offmeans the module is abnormal or means no module is installed in the current slot.
ACTIVEBlinking means data is being received and transmitted by the module on the current slot.Off means no data is being received or transmitted by the module in the current slot.
0 - 7 Position of corresponding slots.
2.5.3 System Description
The following table shows the basic configurations, dimensions, operating environment,etc. of R3680 and R3680E.
Table 2-13 System description of R3680/R3680E
Item Description of R3680 Description of R3680E
SlotA maximum of 8 function modules can be configured according torequirement.
CPU Pentium MMX-166MHz Power PC 8240 250MHz
NVRAM 128KB
BOOT ROM 512KB
Default: 128MBSDRAM None
Max.: 256MB
Default: 64MBDRAM
Max.: 128MBNone
FLASH 8MB
Dimensions Width x Height x Depth = 440mm x 86mm x 400mm
Weight 14kg
AC: 160 to 240V 50/ 60Hz AC: 85 to 264V 50/60HzInput voltage
DC: -40V to -75V
Max. power (with 8 modules) 130W 120W
Operating temperature 0 to 40OC
Operating humidity 10 to 90% non-condensing
Note:
Dynamic memory (DRAM/SDRAM) works as main memory.FLASH stores system programs.
NVRAM stores configuration files.
7/22/2019 HUAWEI QUIDWAY R2600
22/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 3Installation Preparations
3-1
Chapter 3 Installation Preparations
3.1 Safety Recommendations
Routers play the key role in data communications network. Please pay attention to thefollowing:
Warning: It indicates that this operation may seriously damage the router orendanger the operator. Please follow the operation procedures for sake of safety.
Caution: It indicates that during the installation and usage of the router, the
operation needs attention. Though this operation will not do any damage to the routeror endanger the operator, it may affect the normal operation of the router.
Please follow the following safety recommendations during the installation and use ofthe router:
Keep the router away from water or any wet place. Keep the router away from any heat source. Make sure that the router is normally grounded.
Wear ESD-preventive wrist strap during installation. Do not hot unplug the modules of the router. Do not hot unplug any cable.
Always use UPS.
3.2 Installation Conditions
R2600/3600 series must be used indoors. To ensure the normal operation and prolongtheir service life, the following requirements for installation site must be met.
3.2.1 Temperature and Humidity Requirements
Certain requirements on temperature and humidity in the equipment room shall be met.If the relative humidity is too high, the insulation materials in it will deteriorate easily oreven lead to electric leakage. Sometimes this will result in change to the mechanicalperformance of the materials and rusting of the metal components. If the relativehumidity is too low, the fastening screw will become loosen due to shrinkage of theisolation spacer. In an environment with dry climate, the static electricity may beproduced, putting the CMOS of the router to risk. High temperature is of the greatestrisk: for it will significantly degrade the routers reliability, speed up the aging process ofthe insulating materials, and shorten the service life of the router. The requirements onthe temperature and humidity for R2600/3600 series are shown in Table 3-1:
7/22/2019 HUAWEI QUIDWAY R2600
23/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 3Installation Preparations
3-2
Table 3-1 Humidity requirement in the equipment room
Temperature Relative humidity
Normal operating condition Safety operatingcondition
Normal operating condition Safety operatingcondition
15OC to 30OC 0OCto 45OC 40% to 65% 10% to 90%
Note:
1) The values of environmental temperature and humidity in the equipment room are measured at 1.5mhigh and 0.4m away from the front of the router rack when there is no protective board installed in front andat the back of the rack.2) Safety operating condition refers to the continuous operation for less than 48 hours or the accumulativeannual operation time less than 15 days.3) The extreme environment refers to the likely environmental temperature and humidity when the airconditioning system in the equipment room fails (the normal operating condition should be recovered
within five hours for each failure).
3.2.2 Cleanness Requirements
Dust undermines the normal operation of R2600/3600 series. Dust dropping on theequipment can cause electrostatic adsorption, which degrades the contactperformance of the metal connection parts or connectors. This happens more
frequently when the indoor relative humidity is low, which will not only shorten therouters service life, but also cause communication failure.
The recommended specification on dust content and particle diameter in the equipmentroom is shown in Table 3-2:
Table 3-2 Specification on dust content in equipment room
Maxim d iameter ( m) Max. intensity (particles per cubic meter)
0.5 1.4 x 107
1 7 x 105
3 2.4 x 105
5 1.3 x 105
The routers also have rigorous demand on the content of salts, acids and sulfides in theair. These harmful gases will speed up the metal rusting and the aging processes ofcertain parts. The equipment room should be protected from the invasion of harmfulgases such as SO2, H2S, NO2,NH3 and Cl2, the value limits of which are shown in Table3-3:
7/22/2019 HUAWEI QUIDWAY R2600
24/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 3Installation Preparations
3-3
Table 3-3 Value limits for harmful gas contents in equipment room
Gas Average (mg/m3) Max. (mg/m3)
SO2 0.2 1.5H2S 0 0.03
NO2 0.04 0.15
NH3 0.05 0.15
Cl2 0.01 0.3
3.2.3 ESD-Preventive Requirements
Although many antistatic considerations have been given to R2600/3600 series,damage to the routers circuit or even the whole equipment may still happen when the
static electricity exceeds the tolerance threshold.
In the communication network to which the routers are connected, static inductionmainly comes from:
External electric fields such as outdoor high voltage power line or thunder. Internal environment like flooring materials or the whole equipment structure.
Thus, the following should be considered to safeguard the equipment against the staticdamage:
Make sure that the equipment and the floor are well grounded. Make sure that dust-proof measures are taken.
Maintain an appropriate humidity and temperature. Wear an ESD-preventive wrist strap and uniform when contacting the circuit
board.
Place the uninstalled circuit board on the antistatic workbench, with its faceupward, or put it into the electromagnetic shield bag. When observing or removing the uninstalled circuit board, please touch the edge
of the circuit board, and avoid contacting the devices on it.
3.2.4 Anti-interference Requirements
The interference sources, no matter where they come from, affect the routers withcapacitance coupling, inductance coupling, radiation of electromagnetic wave,common impedance (including the grounding system) or conducting line (power line,
signal line and transmission line etc.).
So the following should be considered:
Take effective measures to prevent the power system from being interfered withby the power grid system.
Separate the working ground of the router from the grounding device of the powersupply equipment or anti-lightning grounding device as far as possible.
Keep the router far away from the radio launcher, radar launcher, and high-frequency devices working in high currents.
Use electromagnetic shielding when necessary.
3.2.5 Lightning Protection Requirements
Although many measures have been taken to protect R2600/3600 series from lightning,if the lightning intensity exceeds a certain range, damage to the router may still happen.
To protect the router from lightning better, the following should be considered:
7/22/2019 HUAWEI QUIDWAY R2600
25/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 3Installation Preparations
3-4
Ensure the shell of the chassis is well grounded through the ground wire. Ensure the neutral point of the socket of AC power supply is well grounded. To enhance the lightning protection capability of the power supply, a lightning
arrester could be installed at the input end of the power supply.
As for the signal line led out to the outdoor from the function modules ofR2600/3600 series, such as ISDN line, telephone line, E1 line, etc, a speciallightning arrester should be installed at the input end of the signal line to enhancethe lightning protection capability.
3.2.6 Workbench Requirements
No matter whether you are to install the router in the cabinet or directly place it on theworkbench, it is necessary to ensure that:
There is spacing reserved at the air inlet and outlet in the router so as to facilitatethe radiation of the router cabinet.
The cabinet and workbench have good radiation systems.
The cabinet and workbench are firm enough to support the weight of the routerand other installation accessories.
The cabinet and workbench are well grounded.
3.3 Tools and Devices Required
1) Tools required Phillips screwdriver Flathead screwdriver ESD-preventive wrist strap2) Connection cables Power cable
Console cable Auxiliary cable Ethernet cable Interface cable for selected modules3) Required Devices Ethernet HUB or LANSWITCH CSU/DSU or other DCE Configuration terminal (can be an ordinary PC) Equipment related with selected modules
Caution:
R2600/3600 series are not equipped with any installation tools, and the user has to prepare the tools.
7/22/2019 HUAWEI QUIDWAY R2600
26/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 4Installation
4-1
Chapter 4 Installation
4.1 Installation Flow
Installation completed
Connect the router to the
specified position
Connect various cables
Check after installation
Power on
Configure the router
Preparation and confirmation
Begin to install
Figure 4-1 Flow for installing R2600/3600 series routers
Caution:Before starting the work described in 4.2 and 4.3, please make sure:1) You have carefully read Chapter 3 Installation Preparations.2) The requirements specified in Chapter 3 have been met.
4.2 Mechanical Installation
When you have completed the above work, you can start to install the router.
There are two methods for installing the router depending on the installation position:
7/22/2019 HUAWEI QUIDWAY R2600
27/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 4Installation
4-2
Installing it in the cabinet Placing it on the workbench
4.2.1 Installing the Router in a Cabinet
R2600/3600 series have been designed according to the size of the standard 19-inchcabinet, and their dimensions are respectively:
Quidway R3680, R3680E: Width x height x depth = 440mm x 86mm x 400mm
QuidwayR2630, R2630E, R2631, R2631E, R3640, and R3640E:
Width x height x depth = 440mm x 43mm x 400mm
Quidway R2620, R2621: Width x height x depth = 440mm x 86mm x 300mm
As shown in Figure 4-2, the flow for installing the router is as follows:
Step 1: Check the grounding condition and secureness of the cabinet. Secure thebracket to both sides of the front/rear panel of the router.
Step 2: Place the router on one of the trays in the cabinet. Move the router to a properposition along the guide rail in the cabinet. Leave an appropriate space between therouter and guide rail.
Step 3: Screw the bracket to the fixed guide rail at both sides of the cabinet.
In this way, the router is firmly fixed to the cabinet through the tray at each slot in thecabinet and the bracket of the router.
Figure 4-2 Mechanical installation of the Quidway R26/ 36 series
4.2.2 Installing the Router on Workbench
In most of the cases, you do not have a standard 19-inch cabinet. Then, you can placethe routers on clean workbenches. This is a simple operation. During this operation, theoperator:
Must ensure the stability and good grounding of the workbench.
Must reserve a 10cm for heat-dissipation around the router.
Do not place any heavy object on the router.
7/22/2019 HUAWEI QUIDWAY R2600
28/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 4Installation
4-3
4.3 Power Connection
4.3.1 Connecting Power Cable
R2600/3600 series support the AC/DC power modules (See Chapter 2 Appearanceand System Features). You can select different types of power modules according to
the specific environment where the router is used.
The AC and DC routers of R2600/3600 series have basically the same features andfunctions. They differ in their input voltages only.
I. AC power and power cable
AC power
For the power socket of the AC-input router, see Figure 4-3.
Input power:
180 to 240V, 50/60Hz AC (R2630, R2631, R3640, and R3680)
85 to 264V, 50/60Hz AC (R2630E, R2631E, R3640E, R3680E, R2620 and R2621)
Figure 4-3 Power socket of AC-input router
Recommended AC power socket
A monophase 3-wire power socket with a neutral point connector, or a special powersocket for the computer is recommended. The neutral point of the power in a buildingmust be reliably grounded. Normally, the neutral point of the power supply system in abuilding will have been grounded during the construction and wiring. The user must
make sure that the power supply for the building is earthed.
Neutral point
Zero lineLive line
Figure 4-4 Recommended AC power socket
Connecting AC cable
7/22/2019 HUAWEI QUIDWAY R2600
29/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 4Installation
4-4
Step 1: Connect one end of the ground cable on the chassis accompanying the routerto the ground pin on the routers rear panel, and well ground the other end.
Step 2: After confirming the power switch of the router is turned off, connect one end of
the power line accompanying the router to the power input socket on the routers rearpanel, and connect the other end to the AC socket that delivered with the router.
Step 3: Switch the power switch of the router to the ON position.
Step 4: Check that the power indicator on the rear panel of the router is on. On meansthe power cable is correctly connected.
II. DC power and DC cable
DC power
Input power: -45V to -70V DC
R3640, R3640E, R3680, R3680E, R2630E, and R2631E routers use the DC-input
socket, as shown in Figure 4-5.
Power switch DC-input
Figure 4-5 Power socket of DC-input router (R3640/R3680/R2630E/R2631E/R3640E/R3680E)
R2620 and R2621 routers use the DC-input socket, as shown in Figure 4-6.
Figure 4-6 Power socket of DC-input router (R2620/R2621)
Connecting DC cable
Step 1: Connect one end of the ground cable on the chassis accompanying the routerto the ground pin on the routers rear panel, and well ground the other end.
Step 2: After confirming the power switch of the router is turned off, connect one end ofthe power line accompanying the router to the power socket on the routers rear panel,and connect the other end to the 48V DC power of the switch.
Step 3: Switch the power switch of the router to the ON position.
7/22/2019 HUAWEI QUIDWAY R2600
30/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 4Installation
4-5
Step 4: Check that the power indicator in the rear panel of the router is on. It is on whenthe power cable is correctly connected.
4.3.2 Connecting Ground Cable
Warning:
The normal connection of the routers ground cable is the primary guarantee for the anti-lightning and
anti-interference capability of the router, so you must connect the ground cable carefully.
The AC input connector of R2600/3600 series comes with an AC noise filter unit,whose central ground is directly connected with the cabinet, forming the so-called
chassis ground (also called the protection ground). This chassis must be well groundedso that the induction power and leakage power can be released to the ground toimprove the whole routers performance to withstand electromagnetic interference.This ground also provides protection against the lightning and over-voltage likely to becaused by the external network cable such as the E1 interface and ISDN cables.
The ground point of the chassis is located near the AC power and switch at the back ofthe cabinet, as shown in Figure 4-7. The point shall be connected to the ground.
Ground point
Figure 4-7 Ground point on the chassis
Please connect this point to the ground with a ground cable, and make sure that theground resistance is not greater than 5-ohm. If the router is installed in a standard 19-inch cabinet, then this cabinet should be grounded in the same way.
Warning:
The router must be well grounded for the normal working; otherwise it cannot guard against lightning, and
is likely to cause damage to the router and the far-end equipment connected with this router!
4.4 Connecting Interface Cable on Main Control Panel
Note that Console and AUX interface cannot be used at the same time. You can onlychoose either of them.
7/22/2019 HUAWEI QUIDWAY R2600
31/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 4Installation
4-6
4.4.1 Connecting Console Port
I. Introduction to console
R2600/3600 series provide a console in compliance with the EIA/TIA-232asynchronous serial standard, through which the user can implement the local
configuration of the router.
II. Attributes of console
Table 4-1 Attributes of console
Att rib utes Descr ipt ion
Connector RJ-45
Interface standard Async EIA/TIA-232
Baud rate 9600bps
Services supported
---Command line interface---Connection with the character terminal---Connection with the serial interface of the local PC, and running the terminalemulation program on the PC
III. Console cable
The console cable is an 8-core shielded cable. One end of it is a pressure crimpedRJ-45 connector, and the other end is a connector with a DB-9-pin and a DB-25-pin.You can select either of them based on your actual requirement and plug it with the
25-pin or 9-pin at the configuration terminal. The console cable is shown in Figure 4-8:
Enlarged A side
Pos. 25
A
DB 25 Female8P8C PLUG
Enlarged B side
Pos.1 Pos.8
DB9 FemaleEnlarged C side
Pos.1
Pos.9
CPos.1
B
Figure 4-8 Console cable
7/22/2019 HUAWEI QUIDWAY R2600
32/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 4Installation
4-7
Table 4-2 Console cable pinouts
RJ-45 Signal Direction DB-25 DB-9
1 CTS ---> 5 82 DSR ---> 6 6
3 RXD ---> 3 2
4 GND --- 7 5
5 GND --- 7 5
6 TXD
7/22/2019 HUAWEI QUIDWAY R2600
33/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 4Installation
4-8
III. AUX cable
The AUX cable is an 8-core shielded cable. One end of it has a RJ-45 connectoradopting RS-232 standard, which is to be connected to AUX. The DB-25-pin and DB-
9-pin connector of the other end are plugged with the DB-25-pin or DB-9-pin socket inModem according to the actual requirements. The AUX cable is shown in Figure 4-9:
E n l a r g e d A s i d e
P o s . 1
A
P o s . 2 5
D B 2 5 M a l e
L a b e l
8 P 8 C P L U G
B
P o s . 1 P o s . 8
E n l a rg e d B s i d e
D B 9 M a le
E n l a r g e d C s i d e
P o s . 9
P o s . 1
C
Figure 4-9 AUX cable
Table 4-4 AUX cable pinouts
RJ-45 Signal Direction DB-25 DB-9
1 RTS ---> 4 7
2 DTR ---> 20 4
3 TXD ---> 2 3
4 DCD
7/22/2019 HUAWEI QUIDWAY R2600
34/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 4Installation
4-9
Set up a remote configurationenvironment
AUX cable
MODEM
PSTN
Telephone cable
MODEM
MODEM Serial interface cable
Quidway R3640 660000
Figure 4-10 Setting up remote configuration environment via the AUX interface
Caution:
Console and AUX cannot be used at the same time.
4.5 Connecting Interface Cable
Please refer to Chapter 8 Function Modules.
4.6 Installation Check
On completion of the mechanical installation of the router, please check the followingbefore powering on the router:
If the router is installed in the cabinet, please check that the cabinet and the
bracket of the router are secure. If it is installed on the workbench, please checkthat enough spacing is reserved about the router for heat-dissipation, and that theworkbench is secure.
Check that the power supply connected to the power cable is consistent with thatrequired by the router.
Check that the ground cable of router is correctly connected. Check that the router and configuration terminal and the other devices are
correctly connected.
7/22/2019 HUAWEI QUIDWAY R2600
35/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 4Installation
4-10
Caution:
It is very important to check after the router has been installed. For the normal operation of the router isdirectly affected by following factors: whether the router is mounted firmly, whether it is well grounded, and
whether it uses proper power supply.
7/22/2019 HUAWEI QUIDWAY R2600
36/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 5Startup and Configuration
5-1
Chapter 5 Startup and Configuration
5.1 Starting the Router
If R2600/3600 series are installed and used for the first time, you can only configurethrough the console port.
5.1.1 Setting up Configuration Environment
RS232 Serial interfrace
Console(Console)Cable
Console(Console)
Set up a local configuration
environment
Quidway R3640
Figure 5-1 Setting up a local configuration environment through the console
I. Connecting console port cable
Step 1: Plug the DB-9/25 connector of the console cable to the serial interface in the PCor at the terminal where the router is to be configured.
Step 2: Connect the RJ-45 connector of the console cable to the console.
II. Setting terminal parameters
Step 1: Start the PC or terminal.
If a PC is used for the configuration, it is necessary to run a terminal emulation programon the PC, like Windows3.1 Terminal, and the HyperTerminal of Windows95/98/NT.
Step 2: Set terminal parameters.
Parameter setting requirements:
Set the baud rate to 9600, the data bits to 8, no parity check, stop bit to 1, no traffic
control, and terminal emulation to VT100.
7/22/2019 HUAWEI QUIDWAY R2600
37/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 5Startup and Configuration
5-2
Set the Windows 98 HyperTerminal parameters as follows:
1) In the HyperTerminal window shown in Figure 5-2, click on the button,and a HyperTerminal dialog box will pop up as shown in Figure 5-3.
2) Select the serial interface for connection in[Connect To] in the HyperTerminal
property dialog box. The selected serial interface should be consistent with that ofthe console cable. Click on to access the serial interface propertyconfiguration window shown in Figure 5-4.
3) In the serial interface property dialog box, set the baud rate to 9600, data bit to 8,no parity check, stop bit to 1, and no traffic control. Click on to return to theHyperTerminal property dialog box as shown in Figure 5-3.
4) Select [Setting]in the HyperTerminal property dialog box and access the propertysetting window as shown in Figure 5-5. Select the terminal emulation as VT100,and click on .
Figure 5-2 HyperTerminal window
7/22/2019 HUAWEI QUIDWAY R2600
38/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 5Startup and Configuration
5-3
Figure 5-3 HyperTerminal property dialog box
Figure 5-4 Setting serial interface parameters
7/22/2019 HUAWEI QUIDWAY R2600
39/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 5Startup and Configuration
5-4
Figure 5-5 Setting terminal type
III. Power on the router
After making sure that the router and the configuration terminal are correctly connectedand having completed the setting of configuration terminal parameters, you can poweron the router.
5.1.2 Powering on Router
I. Preparation
Before powering on the router, check:
That the power and ground cables are correctly connected. That the voltage meets the requirements required by the router. That the console cable is correctly connected; the PC or the terminal for
configuration has been started; and the setting is completed.
Warning:
Before powering on the router, please make sure of the position of its power switch so as to cut off powersupply in time when an accident occurs.
7/22/2019 HUAWEI QUIDWAY R2600
40/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 5Startup and Configuration
5-5
II. Powering on the router
Powering on the router as follows:
Switch on the power supply for the router.
Turn on the switch of the router (set the switch of the router to ON).
III. Power-on Check
After the router is powered on, please check:
That the ventilation system works normally
Method: When the router is powered on, you should be able to hear the running of thefan. When placing your hand near the vent of the router, you should be able to feeltheflow of the air.
That the indicator on the front panel of the router is normal
Method: when the router is powered on, the POWER indicator on the front panel is on.
That the configuration terminal displays information normally.Method: when the router is powered on, the terminal will show such system informationas the version of the router.
5.1.3 Starting Router
I. Starting BOOT
When the router is powered, it will run the BOOTROM program first. The screen on theterminal will show the following system information:
Be aware that the BOOTROM terminals of different versions may have slightly differentinterfaces.
Quidway starts booting
******************************************
* *
Quidway Series Router Boot Rom, V4.10
* *
******************************************
Copyright(C) 1999-2001 by Huawei Technologies Co., Ltd.
Now Testing Memory...OK!
64M bytes DRAM
8192K bytes flash memory
Press Ctrl-B to enter Boot Menu ..........
Press , and the system will access the BOOT menu. Otherwise the systemwill initialize.
Note:
Within a few seconds after the appearance of Press Ctrl-B to enter Boot Menu... it is necessary to press to access the BOOT menu; otherwise, the system will begin the program decompressionprocess. To access the BOOT menu after the program decompression process begins; you have to restartthe router.
7/22/2019 HUAWEI QUIDWAY R2600
41/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 5Startup and Configuration
5-6
II. Initializing the system
If the router is powered on, the router will start self-check. When self-check is
completed, the terminal screen will display:
Press ENTER key to get start when you see ATS0=1System now is starting ...ATS0=1
Pressand the screen will show:
Quidway>
This prompt indicates that the router has entered the normal configuration mode (asdescribed in 5.2 Configuration Basic).
Note:
If ATS0=1 appears, it indicates that system initialization has completed and the router works normally.
5.1.4 Configuring Router via Setup
In Setup mode, you are guided in an interactive manner (dialog) to set the necessarybasic parameters for the router.
Setup is usually used for BOOTSTRAP configuration for the router when it is poweredon for the first time, or it can be used at any time in privileged configuration mode (as
described in 5.2 Configuration Basic).
Configurations made in Setup include:
Global parameter:
Hostname of the router Privileged user password SNMP IP
Parameters configured for the interfaces:
IP address IPX address
The specific configuration steps are as follows:
I. Confirming whether to make the configuration
In privileged mode, enterand the following information will be displayed onthe terminal screen:
Quidway#setup
--- System Configuration Dialog ---
Default settings are in square brackets '[]', if you do not change the default
settings, you may input enter. And Ctrl-C can cancel at any time without saving.
Continue with configuration dialog? [yes]:y
[] contains the default system settings. If you do not want to change it, directly press. Press to exit setup mode at any time.
The last line prompts the user to continue with the configuration. Enter to exit theSetup mode.
7/22/2019 HUAWEI QUIDWAY R2600
42/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 5Startup and Configuration
5-7
II. Displaying the interface status
Firstly, would you like to see the current interface summary? [yes]:y
Interface IP-Address OK? Status Protocol
Ethernet0 129.102.100.141 yes down up
Serial0 yes up downSerial1 yes up down
Serial2 yes up down
III. Configuring global parameters
Configuring global parameters:
Enter host name [Quidway]:
Enter enable password []:
Configure SNMP Network Management? [YES]:
Community string []: public
Configure IP? [yes]:
Configure IPX? [NO]: y
IV. Configuring interface
Configuring interface Ethernet0:
Is this interface in use? [YES]:
Configure IP and mask on this interface? [YES]:
IP address for this interface [129.102.100.141]:
Netmask [255.255.0.0]:
Class B network is 129.102.0.0.
IP address is 129.102.100.141, netmask is 255.255.0.0.
Configure IPX on this interface? [NO]:y
IPX network number for this interface [1]:
Configuring interface Serial0:
Is this interface in use? [YES]:
Configure IP on this interface? [NO]:
Configure IPX on this interface? [NO]: y
Configuring interface Serial1:
Is this interface in use? [YES]:
Configure IP on this interface? [NO]:
Configure IPX on this interface? [NO]:
Configuring interface Serial2:
Is this interface in use? [YES]:
Configure IP on this interface? [NO]:
Configure IPX on this interface? [NO]:
V. Displaying configuration results
The following configuration was created:
hostname Quidway
enable password
snmp-server community ro
ipx routing
interface Ethernet0
no shutdown
ip address 129.102.100.141 255.255.0.0
ipx network 1
interface Serial0
no shutdown
no ip address
no ipx network
interface Serial1
no shutdown
no ip address
no ipx network
interface Serial2
7/22/2019 HUAWEI QUIDWAY R2600
43/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 5Startup and Configuration
5-8
no shutdown
no ip address
no ipx network
End
VI. Confirming the configuration
Use this configuration? [yes/no]:
Now writing the configuration to flash memory.
Write the running config to flash memory successfully.
Please reboot the router.
5.2 Configuration Basic
5.2.1 Basic Configuration Mode
The command lines for R2600/3600 series are hierarchically protected to preventunauthorized users from accessing it. It provides a rich diversity of command modesand the three most basic modes are:
Normal mode Privileged mode Global mode
Note:
For the details about configuration commands and command line interfaces, refer to VRP User Manual -Configuration Guide (V1.5).
Table 5-1 Feature list for basic command modes
Commandmode
Feature Prompt Entry command Exit command
Normalmode
View the simple runningstates and statistics of therouter
Quidway>
Access the modeafter connectionwith the router iscreated.
Enter todisconnect theconnection from therouter
Privilegedmode
View the entire running statesand statistics of the router.
File management and systemmanagement can beperformed at the same time
Quidway#
Enter innormal mode andaccess the modeafter entering the
correct enablepassword (nopassword is set forthe router bydefault).
Enter toreturn to the normalmode.
Enter todisconnect theconnection from therouter and return tothe normal mode
Globalmode
Configure global parameters Quidway(config)#In privilegedmode, enter
Enter to returnto privileged mode
Note:
In general, for a certain mode, only the command defined by this mode can be executed.
7/22/2019 HUAWEI QUIDWAY R2600
44/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 5Startup and Configuration
5-9
5.2.2 Help
R2600/3600 series provide a rich set of online help:
1) In any command mode, enter for a brief description for the related help.2) In any command mode, enter for all the commands in this mode and a brief
description about the command.3) Enter a command, followed by separated by a space. If this position is for key
words, all the key words and the related brief description will be given.4) Enter a command, followed by separated by a space. If this position is for
arguments, the descriptions of the related arguments will be listed.5) Enter a character string followed by , and all the commands beginning with this
string will be shown.6) Enter a command, followed by a character string and , and all the key words
beginning with this string will be listed.
7/22/2019 HUAWEI QUIDWAY R2600
45/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 6Maintenance
6-1
Chapter 6 Maintenance
6.1 Software Maintenance
The software maintenance of router includes software upgrade and file uploading/downloading.
The manageable files of the router include:
BOOTROM program file Main program file Configuration file
Thischapter will introduce file uploading and downloading via FTP. The following twomethods are for software upgrade:
Software upgrade via XModem Software upgrade via TFTP
Note:
To upgrade the main program via TFTP and FTP, you need to use the Ethernet interface. Refer to Chapter8 Function Modules for how to connect the Ethernet cables.
6.1.1 BOOT Menu
BOOT menu will be used during the maintenance of the router software.
Attach a terminal (or a PC. For PC, it is necessary to run a terminal emulation program)to the console of the router. After the router is powered on, the following information will
display:
Note:
Different versions of BOOTROM may have slightly different interfaces at the terminal.
Quidway start booting
******************************************
* *
* Quidway Series Router Boot Rom, V4.10 *
* *
******************************************
Copyright(C) 1999-2001 by Huawei Technologies CO., LTD.
Now Testing Memory...OK!
64M bytes DRAM
8192K bytes flash memory
Press Ctrl-B to enter Boot Menu ..........
Press , and the system will access the BOOT menu.
7/22/2019 HUAWEI QUIDWAY R2600
46/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 6Maintenance
6-2
Note:
In order to access the BOOT menu, you shall press within a few seconds after the informationPress Ctrl-B to enter Boot Menu... appears; otherwise the system will enter the program decompression
process. At this time if you want to access the BOOT menu, you will have to restart the router.
The system will prompt:
Please input bootrom password:
You are required to enter the password. After entering correct password (no passwordis set for the router by default), the system will access the BOOT menu:
Caution:
While using the router, please always remember the modified BOOTROM password.
Boot Menu:
1: Download application program with XMODEM
2: Download application program with TFTP
3: Clear application password
4: Clear configuration
5: Exit and reboot
Enter your choice (1-5):
6.1.2 Upgrading Software via XModem
I. Upgrading main program
Step 1: Enter in the BOOT menu, and select to download the application programvia XModem. The router supports the following download speeds:
Please choose your download speed:
1: 9600 bps
2: 19200 bps
3: 38400 bps
4: 57600 bps
5: 115200 bps
6: Exit and Reboot
Enter your choice (1-6): 5
Step 2: Select the appropriate download speed based on the actual requirements. Forexample, enter for 115200bps, the router will provide the following information:
Download speed is 115200 bps. Change the terminal's speed to 115200 bps, and
select XMODEM protocol. Press ENTER key when ready.
Step 3: Follow the above prompt and change the baud rate set at the configurationterminal, so that the baud rate is the same as that of the software download. After thebaud rate of the configuration terminal is completed, disconnect and then re-connectthe terminal. Press to start downloading, the router will provide the followinginformation:
Now Downloading Program File. Please Start Transfer Program File Use Xmodem
Protocol. If You Want To Exit Press . Downloading ... CCCCC
7/22/2019 HUAWEI QUIDWAY R2600
47/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 6Maintenance
6-3
Note:
After the terminal baud rate is modified, it is necessary to disconnect and then re-connect the terminal, soas to effect the new setting.
Step 4: Select [Transfer\Transfer File] from the terminal window, and the followingdialog box will be popped up.
Figure 6-1 [Send File]dialog box
Step 5: Click on , select the program to be downloaded. Change thedownload protocol to XModem. Then click on [Send]and the system will pop up the
interface as shown in Figure 6-2.
Figure 6-2 Xmodem file send interface
Step 6: After the download completes, the system begins to write to the Flash. Whenthis operation completes, the terminal interface displays the following information,
indicating the completion of downloading.
Download completed.
Writing to flash memory...
7/22/2019 HUAWEI QUIDWAY R2600
48/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 6Maintenance
6-4
Please waiting, it needs a long time (about 1 min).
Write Flash Success.
Please return to 9600 bps. Press ENTER key to reboot the system.
II. Upgrading BOOTROM
Step 1: Attach a terminal or a PC (For a PC, it is necessary to run a terminal emulationprogram) to the console of the router. Power on the router for self-check. When theinterface of the terminal running emulation program displays Quidway start booting,press and the system will prompt you to enter the BOOTROM password, as
shown below:
Please input bootrom password:
Step 2: Enter correct password. (By default, there is no BOOTROM password. If therouter has been configured with password, please enter the correct password.) Then
the system displays the following menu:
Boot Menu:
1: Download Bootrom program
2: Modify Bootrom password3: Reboot
Enter your choice (1-3): 1
Step 3: Enter , select to download BOOTROM program, and the subsequent stepsare the same as that in 6.1.2 Upgrading main program.
6.1.3 Upgrading Main Program via TFTP
Note:
While upgrading the main program via TFTP, you need to use the Ethernet interface. For cable connection
method, refer to Chapter 8 Function Modules.
Step 1: Select the Ethernet interface for downloading.
R2600/3600 series support loading application program via a specified Ethernetinterface:
R2630, R2631, R2620 and R2621: Ethernet 0. R3640 and R3640E: search for 1FE board in the order of slots 0, 2, 1, and 3 until
an Ethernet interface is found, and this interface will serve as the downloadEthernet interface. If there is no 1FE, then search for 2FE board in the same order,and Interface 0 of the first 2FE found will serve as the Ethernet interface fordownloading.
R3680 and R3680E: search for 1FE board in the order of slots 0, 2, 4, 6, 1, 3, 5,and 7 until an Ethernet interface is found, and this interface will serve as thedownload Ethernet interface. If there is no 1FE, then search for 2FE board in thesame order, and Interface 0 of the first 2FE found will serve as the Ethernetinterface for downloading.
After specifying the Ethernet interface, connect the interface to a PC (suppose its IPaddress is 10.110.10.13) via Ethernet cable. Attach a PC (can be the same PC) to theconsole of the router.
Step 2: Run the TFTP Server program on the PC connected with the Ethernet, andspecify the directory for the program.
7/22/2019 HUAWEI QUIDWAY R2600
49/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 6Maintenance
6-5
Caution:
TFTP Server program is not supplied together with R2600/3600 series and should be prepared by the
user.
Step 3: Run the terminal emulation program on the PC connected to the console, andboot the router. When the screen displays Quidway start booting, press immediately, and the following will be displayed:
(M)odify any of this or (C)ontinue? [M]
Press , and the following prompt will be given:
For each of the following questions, you can press to select the value
shown in braces, or you can enter a new value.
The above prompt indicates that the following options have default values (thosecontained in [ ] are default values). If there is no need to modify the value, press; or, enter a new value.
NETWORK INTERFACE PARAMETERS:
Do you want a LAN1 interface? [Y]
This board's LAN1 IP address (0.0.0.0 = RARP)? [10.110.10.10]
Subnet mask for LAN1 (0 for none)? [255.255.0.0]
HARDWARE PARAMETERS:
Baud rate for serial channels [9600]
NETUTILS APPLICATION PARAMETERS:
IP address of the TFTP Boot server to boot from? [10.110.200.1]
What is the name of the file to be loaded and started? [ram.abs]
How long (in seconds) should CPU delay before starting up? [2]
IP address of the TFTP Boot server to boot from? [10.110.200.1] must be the IPaddress of the PC connected with the Ethernet. Here, it is 10.110. 10.13.
After entering the last value, the following prompt will be given, requesting you toconfirm the input values:
-------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN1 is 10.110.10.10
LAN1 interface's subnet mask is 0xffff0000
HARDWARE PARAMETERS:
Serial channels will use a baud rate of 9600
NETUTILS APPLICATION PARAMETERS:
IP address of the TFTP host is 10.110.10.13
The file to download and start is ram.abs
After board is reset, start-up code will wait 2 seconds
-------------------------------------------------------------------
(M)odify any of this or (C)ontinue? [M]
Step 4: Enter to confirm the above selection, and BOOTROM will be normallystarted. Then, access the BOOT menu with the method described in 6.1.1.
Step 5: Enter in the BOOT menu, and download the application program via TFTP,and the following prompt will be displayed:
Please start TFTP server then press ENTER key to get start
If the PC running the TFTP Server is ready, press to start the loading.
Starting the TFTP download...
..................................................................
TFTP download completed...
read len=[03713478]
Writing program code to FLASH...
Please waiting,it needs a long time (about 1 min)
WriteFlash Success.Press ENTER key to reboot the system.
7/22/2019 HUAWEI QUIDWAY R2600
50/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 6Maintenance
6-6
The loading is successful. Press , and the router will be rebooted.
Caution:
Please do not upgrade the software system of the router rashly. If necessary, upgrade under the guidance
of technical support engineer.
6.1.4 Uploading and Downloading Files via FTP
R2600/3600 series can serve as the FTP server and enable you to updateconfiguration and program files. Any FTP client can be connected to the router, and beused to upload and download the configuration and program files after passing user
authentication.
Note:
Uploading: Transferring files to the router from the PC running FTP, which is connected to the Ethernetinterface of the router.Downloading: Transferring files from the router to the PC running FTP, which is connected to the Ethernet
interface of the router.
I. Starting the FTP server on the router
1) Set the authentication In global mode, enter . In global mode, enter. In global mode, enter .
Note:
For details of the above commands, please refer to Chapter 1 AAA Configuration and RADIUSConfiguration in 07 Security Configuration of VRP User Manual - Configuration Guide (V1.5).
2) Add username and password
In global mode, enter is entered, it indicatesthat the username is ftp and the password is 123.
3) Start the FTP server
In global mode, enter .
With the above operations, the FTP server is started and the username is set. So anyFTP client program can log in the FTP server with this username and password.
7/22/2019 HUAWEI QUIDWAY R2600
51/134
Installation ManualQuidway R2600/3600 Series Modular Routers
Chapter 6Maintenance
6-7
II. Uploading configuration file
Configure the Ethernet interface address of the router to connect the host running the
FTP client program to the router.
Log in the FTP server with the username and password already set in the router. Takethe FTP client program provided by Windows 98 as an example:
With the DOS prompt, enter (A.B.C.D is the IP address on theEthernet interface of the router).
Under the username prompt, enter the username . Under the password prompt, enter the password . After the authentication,
the user login succeeds, showing the FTP client prompt FTP>. Enter under the prompt.
Under the local file prompt, enter the name of the configuration file to beuploaded.
Under the remote file prompt, enter the name of the uploaded configuration file tobe saved at the router end. This name must be configured at the router end before
the uploading, with a default name as CONFIG. After file uploading is completed, the FTP> prompt is displayed again. Enter
, showing the name and size of the file on the router. If the uploading issuccessful, the size of configuration file should be the same as that on the host.
When the uploading is successful, enter to exit the FTP client program.
III. Uploading program file
Configure the Ethernet interfac
Top Related