HP Switch Software
HP 3500 HP 3800 HP 2910al HP 2615 HP 2620
HP 3500yl HP 2915
HP 5400zl
HP 6200yl
HP 6600
HP 8200zl
15.10September 2012
Comware CLI Commands in ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 1 Sunday, September 9, 2012 6:00 PM
HP Networking
Comware CLI Commands in ProVision Software
HP 3500 HP 3800 HP 2910al HP 2615 HP 2620
HP 3500yl HP 2915
HP 5400zl
HP 6200yl
HP 6600
HP 8200zl
15.10September 2012
Common-CLI-Phase-3-Sept-2012.book Page i Sunday, September 9, 2012 6:00 PM
Hewlett-Packard Company 8000 Foothills Boulevard, m/s 5551 Roseville, California 95747-5551 http://www.hp.com/networking/support
© Copyright 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change with-out notice. All Rights Reserved.
This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Hewlett-Packard.
Publication Number
5998-3593September 2012
Applicable Products
HP 2615 Switches (J9565A) HP 2620 Switches (J9623A, J9624A, J9625A, J9626A, J9627A) HP 2910al Switches (J9145A, J9146A, J9147A J9148A) HP 2915 Switches (J9562A) HP 3500 Switches (J9470A, J9471A, J9472A,
J9473A) HP 3500yl Switches (J8692A, J8693A) HP 3800 Switches (J9573A, J9574A, J9575A, J9576A, J9584A, J9585A, J9586A, J9587A, J9588A) HP 5400zl Switches (J8697A, J8698A, J9447A,
J9448A) HP 6200yl Switch (J8992A) HP 8200zl Switches (J9475A, J8715A/B ) HP 6600 Switches (J9263A, J9264A, J9265A,
J9451A, J9452A)
Trademark Credits
Microsoft, Windows, and Microsoft Windows NT are US registered trademarks of Microsoft Corporation. Java™ is a US trademark of Sun Microsystems, Inc.
Disclaimer
The information contained in this document is subject to change without notice.
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.
Software End User License Agreement and
Hardware Limited Warranty
For the software end user license agreement and the hardware limited warranty information for HP Networking products, visit www.hp.com/networking/support.
Common-CLI-Phase-3-Sept-2012.book Page iii Sunday, September 9, 2012 6:00 PM
v
Contents
Introduction To the ProVision CLI
Comware Command Support in ProVision Software . . . . . . . . . . . . . 1-1
Listing Display Commands in the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
CLI Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Comparing Comware and ProVision Commands . . . . . . . . . . . . . . . . . 1-3
Using CLI Context Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Empty Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Further CLI Operating Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Display Commands
display arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
display arp detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
display arp detection statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
display arp ip-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
display boot-loader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
display clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
display command-alias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
display counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
display counters rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
display cpu-usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
display cpu-usage history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
display current-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
display current-configuration by-linenum . . . . . . . . . . . . . . . . . . . . . . 2-19
display current-configuration configuration . . . . . . . . . . . . . . . . . . . 2-20
display current-configuration interface . . . . . . . . . . . . . . . . . . . . . . . . 2-21
display debugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
display default-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
Common-CLI-Phase-3-Sept-2012.book Page v Sunday, September 9, 2012 6:00 PM
vi
display device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
display dhcp relay information all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
display dhcp relay information interface Vlan-interface <vlan-id> . . . 2-29
display dhcp relay statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
display dhcp-snooping binding database . . . . . . . . . . . . . . . . . . . . . . . 2-34
display dhcp-snooping information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
display dhcp-snooping [ip ip_address] . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
display dhcp-snooping packet statistics . . . . . . . . . . . . . . . . . . . . . . . . 2-37
display dhcp-snooping trust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
display diagnostic-information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40
display dns domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41
display dns domain dynamic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42
display dns < domain | server > . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43
display dns ipv6 server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45
display dot1x [interface] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47
display dot1x [interface …] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56
display dot1x sessions [interface …] . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56
display dot1x statistics [interface …] . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56
display environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-59
display fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60
display fips status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-61
display garp statistics interface <port_list> . . . . . . . . . . . . . . . . . . . . 2-62
display garp timer interface <port_list> . . . . . . . . . . . . . . . . . . . . . . . 2-63
display gvrp state interface <port_list> vlan <vlan-id> . . . . . . . . . 2-64
display gvrp statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66
display gvrp status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-67
display gvrp vlan-operation interface interface-type interface-
number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-69
display history-command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-70
Common-CLI-Phase-3-Sept-2012.book Page vi Sunday, September 9, 2012 6:00 PM
vii
display hwtacacs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-71
display igmp group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-73
display igmp group interface vlan-interface <vlan-id> . . . . . . . . . . 2-75
display igmp group interface vlan-interface <vlan-id> static . . . . 2-77
display igmp group interface vlan-interface <vlan-id> verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-78
display igmp group port-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-80
display igmp group static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-83
display igmp group verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-85
display igmp group x.x.x.x static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-86
display igmp group x.x.x.x verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-87
display igmp interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-88
display igmp interface verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-91
display igmp interface vlan-interface <vlan-id> . . . . . . . . . . . . . . . . 2-93
display igmp routing-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-96
display interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-98
display interface brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-100
display interface brief down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-103
display ip as-path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-105
display ip check source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-106
display ip community-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-108
display ip http . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-109
display ip https . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-110
display ip ip-prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-111
display ipv6 dhcp duid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-112
display ipv6 dhcp relay server-address all . . . . . . . . . . . . . . . . . . . . . 2-113
display ipv6 dhcp relay server-address interface <id> . . . . . . . . . 2-115
display ipv6 dhcp relay statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-117
display ipv6 routing-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-120
display ipv6 routing-table ipv6-address . . . . . . . . . . . . . . . . . . . . . . . 2-122
Common-CLI-Phase-3-Sept-2012.book Page vii Sunday, September 9, 2012 6:00 PM
viii
display ipv6 routing-table protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-124
display lacp system-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-125
display link-aggregation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-127
display link-aggregation member-port . . . . . . . . . . . . . . . . . . . . . . . . 2-128
display link-aggregation summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-130
display link-aggregation verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-132
display lldp local-information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-135
display lldp local-information global . . . . . . . . . . . . . . . . . . . . . . . . . 2-138
display lldp local-information interface interface-type interface-
number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-139
display lldp neighbor-information brief . . . . . . . . . . . . . . . . . . . . . . . 2-141
display lldp neighbor-information list display lldp neighbor-information list system-name <string> . . . 2-143
display lldp statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-144
display lldp statistics global . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-146
display lldp statistics interface interface-type interface-number . . . . 2-147
display lldp status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-149
display lldp status interface interface-type interface number . . 2-150
display lldp tlv-config interface interface-type interface-number . . . . 2-151
display logfile buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-152
display loopback-detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-155
display mac-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-156
display mac-address aging-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-157
display mac-address multicast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-159
display mac-authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-160
display mac-authentication [interface …] . . . . . . . . . . . . . . . . . . . . . 2-165
display memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-167
display mld group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-169
display mld group interface vlan-interface <vid> . . . . . . . . . . . . . . 2-173
Common-CLI-Phase-3-Sept-2012.book Page viii Sunday, September 9, 2012 6:00 PM
ix
display mld group interface vlan-interface <vid> verbose . . . . . . 2-174
display mld group port-info vlan <vlan-id> display mld group port-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-176
display mld group verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-177
display mld group x:x::x:x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-179
display mld group x:x::x:x verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-181
display mld interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-183
display mld interface verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-184
display mld interface vlan-interface <vid> . . . . . . . . . . . . . . . . . . . . 2-186
display mld interface vlan-interface <vid> verbose . . . . . . . . . . . . 2-187
display mld routing-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-189
display monitor-link group [group-number | all], . . . . . . . . . . . . . . 2-190
display multicast forwarding-table . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-192
display multicast routing-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-193
display multicast routing-table static . . . . . . . . . . . . . . . . . . . . . . . . . 2-195
display multicast rpf-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-197
display ospf cumulative . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-198
display ospf interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-201
display ospf lsdb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-204
display ospf peer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-207
display ospf routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-209
display ospf vlink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-211
display ospfv3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-213
display ospfv3 area area-id peer interface interface-type interface
number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-215
display ospfv3 area area-id peer peer-router-id . . . . . . . . . . . . . . 2-216
display ospfv3 area area-id peer verbose . . . . . . . . . . . . . . . . . . . . . 2-219
display ospfv3 interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-221
display ospfv3 lsdb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-225
display ospfv3 lsdb statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-227
Common-CLI-Phase-3-Sept-2012.book Page ix Sunday, September 9, 2012 6:00 PM
x
display ospfv3 peer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-228
display ospfv3 peer peer-router-id . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-230
display ospfv3 peer statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-233
display ospfv3 peer verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-234
display ospfv3 statistic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-237
display ospfv3 vlink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-240
display pim bsr-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-242
display pim control-message counters . . . . . . . . . . . . . . . . . . . . . . . . 2-246
display pim grafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-247
display pim interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-248
display pim interface verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-250
display pim join-prune . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-254
display pim neighbor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-255
display pim neighbor <ip> verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-257
display pim routing-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-260
display pim rp-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-261
display poe device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-262
display poe interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-263
display poe interface power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-265
display poe power-usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-267
display poe-power alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-268
display poe-power switch state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-269
display port trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-270
display power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-271
display protocol-vlan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-272
display protocol-vlan interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-273
display public-key local rsa public . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-274
display public-key peer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-276
display radius scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-277
display rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-283
Common-CLI-Phase-3-Sept-2012.book Page x Sunday, September 9, 2012 6:00 PM
xi
display rip interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-284
display rip process-id ip-address mask/mask-length . . . . . . . . . . . 2-285
display rip process-id route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-286
display rip process-id route peer ip-address . . . . . . . . . . . . . . . . . . . 2-287
display rmon statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-288
display route-policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-289
display saved-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-291
display saved-configuration by-linenum . . . . . . . . . . . . . . . . . . . . . . 2-293
display schedule reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-295
display sflow display sflow slot <slot-number> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-296
display snmp-agent community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-298
display snmp-agent group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-299
display snmp-agent local-engineid . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-302
display snmp-agent mib-view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-303
display snmp-agent statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-304
display snmp-agent sys-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-305
display snmp-agent trap-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-306
display snmp-agent usm-user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-308
display ssh client source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-309
display ssh server session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-310
display ssh server-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-311
display ssh server status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-312
display ssl client-policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-314
display ssl server-policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-316
display startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-318
display stp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-319
display stp abnormal-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-322
Common-CLI-Phase-3-Sept-2012.book Page xi Sunday, September 9, 2012 6:00 PM
xii
display stp bpdu-statistics display stp bpdu-statistics interface GigabitEthernet <port-num> display stp bpdu-statistics interface GigabitEthernet <port-num>
instance <instanceNUM, 1-32> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-324
display stp brief display stp instance <instance-id> brief display stp instance <instance-id> interface GigabitEthernet
<interface-id> brief display stp instance <instance-id> interface GigabitEthernet
<interface-id> brief display stp instance <instance-id> interface GigabitEthernet
<interface-id> to GigabitEthernet <interface-id> brief display stp instance <instance-id> slot <slot-id> brief display stp interface GigabitEnterface <port-num> brief display stp interface GigabitEnterface <port-num> to
GigabitEnterface <port-num> brief . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-327
display stp down-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-329
display stp history display stp history slot <slot-number> display stp instance <instance-id> history slot <slot-no> display stp instance <instance-id> history . . . . . . . . . . . . . . . . . . . . 2-330
display stp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-332
display stp instance <instance-id> interface GigabitEthernet 1/0/1/ . 2-332
display stp slot <slot-num> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-332
display stp instance <instanceid> tc display stp instance <instanceid> tc slot <slot-no> display stp tc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-334
display stp region-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-335
display stp root . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-337
display switchover state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-338
display system-failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-340
display this . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-341
display transceiver alarm interface . . . . . . . . . . . . . . . . . . . . . . . . . 2-342
display transceiver diagnosis interface . . . . . . . . . . . . . . . . . . . . . . . 2-347
display transceiver interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-350
Common-CLI-Phase-3-Sept-2012.book Page xii Sunday, September 9, 2012 6:00 PM
xiii
display transceiver manuinfo interface . . . . . . . . . . . . . . . . . . . . . . . 2-353
display user-bind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-355
display vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-356
display vrrp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-357
display vrrp interface <interface-type> vrid <virtual routerid> 2-359
display vrrp statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-360
display vrrp statistics interface <interface-type> vrid <virtual router-
id> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-362
display vrrp verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-363
Fundamental Commands
backup startup-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
clock datetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
clock summer-time one-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
clock summer-time repeating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
clock timezone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
command accounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
command authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
command-alias enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
command-alias mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
delete <startup-config> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
flow-control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
idle-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
quit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
reset saved-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
restore startup-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Common-CLI-Phase-3-Sept-2012.book Page xiii Sunday, September 9, 2012 6:00 PM
xiv
schedule reboot at . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
schedule reboot delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
screen-length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
set authentication password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
startup saved-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
sysname . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
system-view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
telnet ipv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
telnet server enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
terminal type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
tftp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
tftp ipv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
undo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-34
Common-CLI-Phase-3-Sept-2012.book Page xiv Sunday, September 9, 2012 6:00 PM
xv
Product Documentation
About Your Switch Manual Set
N o t e For the latest version of all HP switch documentation, including Release Notes covering recently added features, please visit the HP Networking web site at www.hp.com/Networking/support.
Electronic Publications
The latest version of each of the publications listed below is available in PDF format on the HP Networking web site, as described in the Note at the top of this page.
■ Installation and Getting Started Guide—Explains how to prepare for and perform the physical installation and connect the switch to your network.
■ Basic Operation Guide—Describes how to use the switch interfaces and introduces basic operations.
■ Management and Configuration Guide—Describes how to configure, manage, and monitor basic switch operation.
■ Advanced Traffic Management Guide—Explains how to configure traffic management features such as VLANs, MSTP, QoS, and Meshing.
■ Multicast and Routing Guide—Explains how to configure IGMP, PIM, IP routing, and VRRP features.
■ Access Security Guide—Explains how to configure access security fea-tures and user authentication on the switch.
■ IPv6 Configuration Guide—Describes the IPv6 protocol operations that are supported on the switch.
■ Command Line Interface Reference Guide—Provides a comprehensive description of CLI commands, syntax, and operations.
■ Event Log Message Reference Guide—Provides a comprehensive descrip-tion of event log messages.
■ Comware CLI Commands in ProVision Software —Lists and describes the Comware CLI commands supported in ProVision Software.
■ Release Notes—Describe new features, fixes, and enhancements that become available between revisions of the main product guide.
Common-CLI-Phase-3-Sept-2012.book Page xv Sunday, September 9, 2012 6:00 PM
1-1
Introduction To the ProVision CLIComware Command Support in ProVision Software
1
Introduction To the ProVision CLI
Comware Command Support in ProVision Software
The selected Comware CLI commands described in this guide are included in the ProVision software CLI to help Comware-experienced network manage-ment staff learn to use the ProVision software CLI with a minimum of effort.
This edition of Comware CLI Commands in ProVision Software describes the operation and output of selected Comware display commands added to the ProVision software. Included are related ProVision software commands and references to further information on configuring the features reflected in the display command output.
Refer to the latest release notes for your switch product to determine whether Comware commands are supported.
HP Networking Switches Running Comware Software
HP Networking Switches Running ProVision Software with Comware CLI Commands Included*
3100330036003610
4200G4210
4210G4500G4510G4800G
5120 El5120 Sl
55005500 E5500 Hl5500 SL5500G58005810
582058305900750095001050012500
3500 3500 yl5400 zl6200 yl
66008200 zl
3800 2910al 26152915
2620
*As of September, 2012. Supported commands depend on software version running on the switch.
Common-CLI-Phase-3-Sept-2012.book Page 1 Sunday, September 9, 2012 6:00 PM
1-2
Introduction To the ProVision CLIListing Display Commands in the CLI
Commands Added to the Software Over Several Releases. The Comware command set available on your switch is determined by the code version it is running. Each command description in this guide includes the minimum software version supporting that command. For example, a minimum version of 15.10 means that a switch running K-code must be using Release K.15.10 or greater and a switch running RA-code must be using RA.15.10 or greater.
Listing Display Commands in the CLI
Use this command: display ?
For example:
HP Switch> display ? boot-loader Display boot loader information clock Clock status and configuration information. command-alias Display command alias debugging Current setting of debugging switches. dns DNS status and configuration information gvrp GARP VLAN Registration Protocol history-command The historical command information. igmp IGMP status and configuration information ip Specify IP(Internet Protocol) configuration information. lacp Display LACP protocol information link-aggregation Display Link-aggregation information memory Display memory information. mld MLD status and configuration information. ospf Open Shortest Path First (OSPF) ospfv3 Open Shortest Path First for IPv6 (OSPFv3) schedule Schedule system task snmp-agent SNMP status and configuration information HP Switch> display
Common-CLI-Phase-3-Sept-2012.book Page 2 Sunday, September 9, 2012 6:00 PM
1-3
Introduction To the ProVision CLICLI Operation
CLI Operation
Comparing Comware and ProVision Commands
Comware display commands and ProVision software show commands produce status information used for monitoring, troubleshooting, and auditing the switch network environment and configuration.
■ Like show commands, using display commands does not change the switch operating mode.
■ Comware display commands are additional commands supported in Pro-Vision software, and do not replace any existing ProVision commands.
Output Differences Between Display and Show commands
The output fields from display commands and their show command counter-parts include differences in the names, numbers and types of information fields. For example the results for the following commands have two instances where there is not a comparable mapping between Comware and ProVision:
DNS Field Mappings.
Comware Related ProVision
display dns < domain | server > show ip dnsshow ip
Comware Related ProVision
No. n/a
DNS Server Priority
Type DNS Mode
Domain-name Domain Suffix
IP Address DNS Server Addresses
n/a DNS Servers Configured
Common-CLI-Phase-3-Sept-2012.book Page 3 Sunday, September 9, 2012 6:00 PM
1-4
Introduction To the ProVision CLICLI Operation
Using both the display commands and their show command counterparts can in some cases result in more information output than using only one or the other.
In some cases, a field populated in Comware display output is not populated in the corresponding display output in ProVision software. This is often due to MIB (Management Information Base) differences between Comware and ProVision software. Also, in rare cases, the Comware display output in ProVi-sion software includes fields that are not included in the same display command output in Comware software.
Using CLI Context Levels
ProVision software operates in these CLI context levels:
Use exit to return to the next-highest context level.
Listing Commands Available at Any Context Level. At a given context level you can list and execute the commands that level offers, plus all of the commands available at preceding levels. To list available commands, use the [?] key. For example:
Use the [Tab] or [?] Key To Complete a Command Keyword. You can use [Tab] or [?] to help you find CLI commands or to quickly complete a keyword. For example:
Level Prompt Context Keyword
Operator HP Switch>
Manager HP Switch# enable
Global Configuration HP Switch(config)# config
Context Configuration HP Switch(vlan-1)# HP Switch(eth-A1-A6)#
vlan n interface << portx >[-portn] >
HP Switch# show vlans ? custom Show vlan parameters in customized order. ports Show VLANs that have at least one port from the 'PORT-LIST' as a member. VLAN-ID Show detailed VLAN information for the VLAN with the ID supplied. <cr>
Common-CLI-Phase-3-Sept-2012.book Page 4 Sunday, September 9, 2012 6:00 PM
1-5
Introduction To the ProVision CLICLI Operation
HP Switch(config) # show ip a[Tab] aspath-list authorized-managers
HP Switch(config) # show ip au[?] HP Switch(config)# show ip authorized-managers [Enter]
IPV4 Authorized Managers ------------------------ Address : 10.10.123.39 Mask : 255.255.255.255 Access : Manager Access Method : all
Empty Output
In some cases where the MIB is not holding information for a feature, the related display command(s) will return only the system prompt. For example, IGMP can be configured, but no data will be displayed unless one or more multicast groups have been joined. For example, using display igmp group when there are no joined multicast groups returns only the system prompt:
HP Switch# display igmp group HP Switch#
Further CLI Operating Information
For more information on using the CLI, refer to the chapter titled “Using the Command Line Interface (CLI)” in the latest Basic Operation Guide for your switch.
To access the latest software manual set for your switch, visit
www.hp.com/support/manuals
Common-CLI-Phase-3-Sept-2012.book Page 5 Sunday, September 9, 2012 6:00 PM
2-1
Display Commandsdisplay arp
2
Display Commands
display arp
Displays ARP (Address Resolution Protocol) configuration information.
Field Descriptions
IP Address: IP address in an ARP entry.
MAC Address: MAC address in an ARP entry.
VLAN ID: VLAN ID contained in a static ARP entry
Interface: Outbound interface in an ARP entry.
Aging: Age timer for a dynamic ARP entry in minutes.
Type: ARP entry type:
• D for Dynamic
• S for Static
• L for Local
• I for Invalid
Comware Related ProVision
display arp show arp
HP Switch(config)# display arp
Type: S-Static D-Dynamic L-Local I-Invalid O-Other
IP Address MAC Address VLAN ID Interface Aging Type120.85.204.1 002347-bbd940 1 1 n/a D
Common-CLI-Phase-3-Sept-2012.book Page 1 Sunday, September 9, 2012 6:00 PM
2-2
Display Commandsdisplay arp
• O for Other
Operating Notes
The types “A” for authorized, and “M” for multiple ports, are not supported.
For more on switch ARP operation, refer to the “IP Routing” chapter in the latest Multicast and Routing Guide for your switch.
Example of Related ProVision Software Command Output.
display arp Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
IP Address IP Address
MAC Address MAC Address
VLAN ID n/a
Interface Port
Aging n/a
Type Type
HP Switch# show arp
IP ARP table
IP Address MAC Address Type Port --------------- ----------------- ------- ---- 15.255.128.1 00000c-07ac00 dynamic 1 15.255.130.156 001635-679d6c dynamic 1 15.255.131.209 0025b3-4afd68 dynamic 1
Common-CLI-Phase-3-Sept-2012.book Page 2 Sunday, September 9, 2012 6:00 PM
2-3
Display Commandsdisplay arp detection
display arp detection
Displays arp-protected VLANs.
HP Switch# display arp detectionARP detection is enabled in the following VLANs: 1-100
Example of Related ProVision Software Command Output.
HP Switch# show arp-protectARP Protection InformationEnabled Vlans : 1-4094Validate : dest-mac, src-macPort Trust----- -----B1 YesB2 YesB3 NoB4 NoB5 No
For more information, see the latest Access Security Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display arp detection show arp-protect
Common-CLI-Phase-3-Sept-2012.book Page 3 Sunday, September 9, 2012 6:00 PM
2-4
Display Commandsdisplay arp detection statistics
display arp detection statistics
Displays the statistics of the detected arp.
HP Switch# display arp detection statistics
ARP detection is enabled in the following VLANs:
1-10
ARP Protection Counters for VLAN 1
ARPs forwarded : 0 Bad Sender/Target IP : 0 Bad bindings : 0 Source/Sender MAC mismatches : 0 Malformed pkts : 0 Dest/Target MAC mismatches : 0
ARP Protection Counters for VLAN 2
ARPs forwarded : 0 Bad Sender/Target IP : 0 Bad bindings : 0 Source/Sender MAC mismatches : 0 Malformed pkts : 0 Dest/Target MAC mismatches : 0
ARP Protection Counters for VLAN 10
ARPs forwarded : 0 Bad Sender/Target IP : 0 Bad bindings : 0 Source/Sender MAC mismatches : 0 Malformed pkts : 0 Dest/Target MAC mismatches : 0
ARP Protection Counters for VLAN 12
ARPs forwarded : 0 Bad Sender/Target IP : 0 Bad bindings : 0 Source/Sender MAC mismatches : 0 Malformed pkts : 0 Dest/Target MAC mismatches : 0
Example of Related ProVision Software Command Output.
HP Switch# show arp-protect statistics 1
ARP Protection Counters for VLAN 1 ARPs forwarded : 0 Bad Sender/Target IP : 0 Bad bindings : 0 Source/Sender MAC mismatches : 0 Malformed pkts : 0 Dest/Target MAC mismatches : 0
Minimum Software Version: 15.10.
Comware Related ProVision
display arp detection statistics show arp-protection statistics
Common-CLI-Phase-3-Sept-2012.book Page 4 Sunday, September 9, 2012 6:00 PM
2-5
Display Commandsdisplay arp ip-address
display arp ip-address
Displays the ARP entry for a specified IP address.
HP Switch# display arp 20.1.1.1
Type: S-Static D-Dynamic L-Local I-Invalid O-Other
IP Address MAC Address VLAN ID Interface Aging Type20.1.1.1 002347-bbd940 1 1 n/a D
Example of Related ProVision Software Command Output.
HP Switch# show arpIP ARP tableIP Address MAC Address Type Port--------------- ----------------- ------- ----15.255.128.1 00000c-07ac00 dynamic B115.255.131.19 00a0c9-b1503d dynamic15.255.133.150 000bcd-3cbeec dynamic B1
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display arp ip-address show arp
Common-CLI-Phase-3-Sept-2012.book Page 5 Sunday, September 9, 2012 6:00 PM
2-6
Display Commandsdisplay boot-loader
display boot-loader
Displays the current flash memory precedence and the source of the current boot file (software image). The switch has two flash memory locations: primary and secondary. In the display boot-loader output:■ btm.swi is the primary flash memory.
■ secondary.swi is the secondary flash memory.
When the switch is configured with primary flash as the default boot source, this command shows that the primary boot file (software image) is in primary flash (btm.swi):
HP Switch# display boot-loader The next primary boot file of MM is: flash:/cfa0/btm.swi The next backup boot file of MM is: flash:/cfa0/secondary.swi The current boot file of MM is: flash:/cfa0/btm.swi
When the switch is configured with secondary flash as the default boot source, this command shows that the primary boot file (software image) is in second-ary flash (secondary.swi):
HP Switch# display boot-loader The next primary boot file of MM is: flash:/cfa0/secondary.swi The next backup boot file of MM is: flash:/cfa0/btm.swi The current boot file of MM is: flash:/cfa0/secondary.swi
Field Descriptions
next primary boot file: The current default flash memory location for the next reload or boot operation.Can be either the primary or secondary flash.
next backup boot file: The current non-default flash memory location. Can be either the primary or secondary flash.
current boot file: The flash memory location from which the switch was last booted. Can be either primary or secondary flash.
Note “of MM” appears in the display boot-loader output on switches that support dual memory modules, and refers to the current active (Actv) memory module.
Comware Related ProVision
display boot-loader show flash
Common-CLI-Phase-3-Sept-2012.book Page 6 Sunday, September 9, 2012 6:00 PM
2-7
Display Commandsdisplay boot-loader
Operating Notes
Both the primary flash and a secondary flash contain a software image. Any valid software image can be loaded into either flash memory.
This command indicates which flash memory is the default when the switch is booted with any of the following commands:
reload
boot [system ]
To change the flash memory default, use this command:
boot set-default flash < primary | secondary >
For more on switch memory operation, refer to the “Switch Memory and Configuration” chapter in the latest Basic Operation Guide for your switch.
Example of Related ProVision software Command Output.
HP Switch# show flashImage Size (bytes) Date Version
----------------- ------------ -------- --------------
Primary Image : 14995368 12/20/11 K.15.07.0003
Secondary Image : 14995368 12/20/11 K.15.08.0001
Boot ROM Version : K.15.26
Default Boot : Primary
Boot-Loader Field Mappings.
Minimum Software Version: 15.08.
Comware ProVision software
btm.swi Primary Image
secondary.swi Secondary Image
n/a Boot ROM Version
current boot file Default Boot
Common-CLI-Phase-3-Sept-2012.book Page 7 Sunday, September 9, 2012 6:00 PM
2-8
Display Commandsdisplay clock
display clock
Displays the current time, time zone, day, and date setting on the switch.
HP Switch# display clock 16:07:27 GMT Mon 03/16/2012
Field Descriptions:
Time: Current time in HH:MM:SS format on the switch.
Time Zone: GMT (default) or the configured time zone.
Day: Mon, Tue, Wed, thu, Fri, Sat, Sun
Date: MM/DD/YYYY format
Operating Notes
To configure time, date, daylight-time-rule, time zone and other time or date settings on the switch, use the following commands in the config context to list the time and date command options:
time ?
clock ?
Example of Related ProVision Software Command Output.
HP Switch# show time Mon Mar 16 16:07:56 2012
The output of the ProVision software show system information command includes the switch’s time zone and Daylight Time Rule settings.
To configure time and date settings on the switch, use the clock and time commands in the config context. For more information, see the “Time Proto-cols” chapter in the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.08.
Comware Related ProVision
display clock show timeshow system information
Common-CLI-Phase-3-Sept-2012.book Page 8 Sunday, September 9, 2012 6:00 PM
2-9
Display Commandsdisplay command-alias
display command-alias
Displays any defined command aliases and their corresponding command assignments configured on the switch. For example, suppose the following aliases are configured:
Alias Full Command
sst show startup-config
srun show running-config
With the above alias configuration, the display output would be as follows:
HP Switch(config)# display command-alias index alias command key 1 sst show startup-config 2 srun show runnning-config
Field Descriptions
index: The sequence number for each alias.
alias: The character string.
command key: The command called by the alias.
Operating Notes
To configure an alias in ProVision software, use the following command.
alias < alias-name-str > < command-str >
For more on the alias command, refer to the chapter titled “Using the Command Line Interface (CLI)” in the latest Basic Operation Guide for your switch.
Comware Related ProVision
display command-alias show alias
Common-CLI-Phase-3-Sept-2012.book Page 9 Sunday, September 9, 2012 6:00 PM
2-10
Display Commandsdisplay command-alias
Example of Related ProVision software Command Output.
HP Switch(config)# show alias
Name Command -------------------------------- -------------------------- sst show startup-config srun show runnning-config
Alias Field Mappings.
Minimum Software Version: 15.08.
Comware ProVision Software
index n/a
alias Name
command key Command
Common-CLI-Phase-3-Sept-2012.book Page 10 Sunday, September 9, 2012 6:00 PM
2-11
Display Commandsdisplay counters
display counters
Displays traffic statistics for interfaces.
Field Descriptions
Interface: Abbreviated interface name.
Total (pkts): Total number of packets received or sent through the interface.
Broadcast (pkts): Total number of broadcast packets received or sent through the interface. On an RPR physical port, all broadcast and multicast packets received or sent are displayed as multicast packets.
Comware Related ProVision
display counters show interface <port>
HP Switch# display counters inbound interfaceInterface Total(pkts) Broadcast(pkts) Multicast(pkts) Err(pkts)A1 11 2 5 0A2 0 0 0 0A3 0 0 0 0A4 0 0 0 0A5 0 0 0 0A6 0 0 0 0A7 0 0 0 0...
HP Switch# display counters outbound interfaceInterface Total(pkts) Broadcast(pkts) Multicast(pkts) Err(pkts)A1 13 6 6 0A2 0 0 0 0A3 0 0 0 0A4 0 0 0 0A5 0 0 0 0A6 0 0 0 0A7 0 0 0 0...
Common-CLI-Phase-3-Sept-2012.book Page 11 Sunday, September 9, 2012 6:00 PM
2-12
Display Commandsdisplay counters
Multicast (pkts): Total number of multicast packets received or sent through the interface. On an RPR physical port, all broadcast and multicast packets received or sent are displayed as multicast packets.
Err (pkts): Total number of error packets received or sent through the interface.
Overflow: more than 14 decimal digits(7 digits for column “Err”): The com-mand displays Overflow in any of the following cases:
• The data length of an error statistic is greater than 7 decimal digits.
The data length of a non-error statistic is greater than 14 decimal digits.
--: not supported: The statistical item is not supported.
Operating Notes
For more information on interface counters, see the “Port Status and Config-uration” chapter in the latest Management and Configuration Guide for your switch.
Common-CLI-Phase-3-Sept-2012.book Page 12 Sunday, September 9, 2012 6:00 PM
2-13
Display Commandsdisplay counters
Example of Related ProVision Software Command Output.
display counters Field Mappings.
HP Switch(config)# show interface a1
Status and Counters - Port Counters for port A1
Name : O’[email protected] MAC Address : 001871-b995ff Link Status : Up Totals (Since boot or last clear) : Bytes Rx : 2,763,197 Bytes Tx : 22,972 Unicast Rx : 2044 Unicast Tx : 128 Bcast/Mcast Rx : 23,456 Bcast/Mcast Tx : 26 Errors (Since boot or last clear) : FCS Rx : 0 Drops Tx : 0 Alignment Rx : 0 Collisions Tx : 0 Runts Rx : 0 Late Colln Tx : 0 Giants Rx : 0 Excessive Colln : 0 Total Rx Errors : 0 Deferred Tx : 0 Others (Since boot or last clear) : Discard Rx : 0 Out Queue Len : 0 Unknown Protos : 0 Rates (5 minute weighted average) : Total Rx (bps) : 3,028,168 Total Tx (bps) : 1,918,384 Unicast Rx (Pkts/sec) : 5 Unicast Tx (Pkts/sec) : 0 B/Mcast Rx (Pkts/sec) : 71 B/Mcast Tx (Pkts/sec) : 0 Utilization Rx : 00.30 % Utilization Tx : 00.19 %
Comware ProVision Software
Interface port
Total (pkts) Bytes Rx and Bytes Tx
Broadcast (pkts) Bcast/Mcast Rx and Bcast/Mcast Tx
Multicast (pkts) Bcast/Mcast Rx and Bcast/Mcast Tx
Err (pkts) Errors
Common-CLI-Phase-3-Sept-2012.book Page 13 Sunday, September 9, 2012 6:00 PM
2-14
Display Commandsdisplay counters
Minimum Software Version: 15.09.
Overflow: n/a
-: not supported n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 14 Sunday, September 9, 2012 6:00 PM
2-15
Display Commandsdisplay counters rate
display counters rate
Displays traffic rate statistics over the last 300 seconds. The statistics cover only interfaces in up state.
HP Switch# display counters rate outbound interfaceInterface Total(pkts/sec) Broadcast(pkts/sec) Multicast(pkts/sec)A1 84 0 42A2 0 0 0
Overflow: n/a --: not supported.
HP-5406zl# display counters rate inbound interfaceInterface Total(pkts/sec) Broadcast(pkts/sec) Multicast(pkts/sec)A1 0 0 0A2 88 0 44
Overflow: n/a --: not supported.
When all ports are down:
HP Switch# display counters rate outbound interface No statistics, or no counted interface.
Example of Related ProVision Software Command Output.
HP Switch# show int custom 1-4 port name:4 type vlan intrusion speed enabled mdiStatus and Counters - Custom Port Status IntrusionPort Name Type VLAN Alert Speed Enabled MDI-mode---- ---- ---- ------ ------- --------- ------- ------1 Acco 100/1000T 1 No 1000FDx Yes Auto2 Huma 100/1000T 1 No 1000FDx Yes Auto3 Deve 100/1000T 1 No 1000FDx Yes Auto4 Lab1 100/1000T 1 No 1000FDx Yes Auto
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display counters rate show int <int>
Common-CLI-Phase-3-Sept-2012.book Page 15 Sunday, September 9, 2012 6:00 PM
2-16
Display Commandsdisplay cpu-usage
display cpu-usage
Displays average CPU usage statistics for 5 seconds, 1 minute and 5 minutes.
HP Switch# display cpu-usage
Master CPU usage: 6% in last 5 seconds 4% in last 1 minute 3% in last 5 minutes
Example of Related ProVision Software Command Output.
HP Switch# show cpu2 percent busy, from 2865 sec ago1 sec ave: 9 percent busy5 sec ave: 9 percent busy1 min ave: 1 percent busy
% CPU | Description-------+--------------------------99 | Idle
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display cpu-usage show cpu [slot <SLOT-ID-RANGE> [ <time>] | <time>]
Common-CLI-Phase-3-Sept-2012.book Page 16 Sunday, September 9, 2012 6:00 PM
2-17
Display Commandsdisplay cpu-usage history
display cpu-usage history
Displays the history CPU utilization rates in a coordinate plane. The system collects the statistics of history CPU utilization rates at a certain interval and saves the statistics in the history record area. You can use the this command to display the history CPU utilization rates in the last 5 minutes. The history CPU utilization rates are displayed through x and y coordinates.
Any CPU utilization statistics value takes the closest y-coordinate value. For example, a statistics value of 53% is displayed as 55%, and a statistics value of 52% is displayed as 50%.
A number sign (#) shows the CPU utilization rate at a time point. If more than one number sign exists at a time point, the highest one represents the CPU utilization rate of the time point.
HP Switch# display cpu-usage history
100%| 95%| 90%| 85%| 80%| 75%| 70%| 65%| 60%| 55%| 50%| 45%| 40%| 35%| 30%| 25%| 20%| 15%| 10%| 5%|######################################################## --------------------------------------------------------- 50 100 150 200 250 300 (seconds) cpu-usage last 05 minutes(SYSTEM)
Minimum Software Version: 15.10.
Comware Related ProVision
display cpu-usage history No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 17 Sunday, September 9, 2012 6:00 PM
2-18
Display Commandsdisplay current-configuration
display current-configuration
Displays the current configuration.
HP Switch# display current-configurationJ8697A Configuration Editor; Created on release #K.15.09.0000xVer #03:01.1f.ef:f2hostname "HP-5406zl"module 1 type J9536Amodule 6 type J9534Asnmp-server community "public" Unrestrictedvlan 1 name "DEFAULT_VLAN" untagged A1-A22,F1-F24 ip address dhcp-bootp exit
Example of Related ProVision Software Command Output.
HP Switch# show running-configRunning configuration:; J9087A Configuration Editor; Created on release #R.11.XXhostname "Switch"snmp-server community "public" Unrestrictedsnmp-server host 15.255.133.236 "public"snmp-server host 15.255.133.222 "public"snmp-server host 15.255.133.70 "public"snmp-server host 15.255.134.235 "public"vlan 1name "DEFAULT_VLAN"untagged 1-28ip address dhcp-bootpexitsnmp-server enable traps mac-notify mac-movesnmp-server enable traps mac-notify trap-interval 60snmp-server enable traps mac-notifymac-notify traps 5-6 learnedmac-notify traps 3-4 removed
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display current-configuration show running-configuration
Common-CLI-Phase-3-Sept-2012.book Page 18 Sunday, September 9, 2012 6:00 PM
2-19
Display Commandsdisplay current-configuration by-linenum
display current-configuration by-linenum
Displays the number of each line.
HP Switch# display current-configuration by-linenum 1: J8697A Configuration Editor; Created on release #K.15.09.0000x 2: Ver #03:01.1f.ef:f2 3: hostname "HP-5406zl" 4: module 1 type J9536A 5: module 6 type J9534A 6: snmp-server community "public" Unrestricted 7: vlan 1 8: name "DEFAULT_VLAN" 9: untagged A1-A22,F1-F24 10: ip address dhcp-bootp 11: exit
Example of Related ProVision Software Command Output.
HP Switch# show running-configRunning configuration:; J9087A Configuration Editor; Created on release #R.11.XXhostname "Switch"snmp-server community "public" Unrestrictedsnmp-server host 15.255.133.236 "public"snmp-server host 15.255.133.222 "public"snmp-server host 15.255.133.70 "public"snmp-server host 15.255.134.235 "public"vlan 1name "DEFAULT_VLAN"untagged 1-28ip address dhcp-bootpexitsnmp-server enable traps mac-notify mac-movesnmp-server enable traps mac-notify trap-interval 60snmp-server enable traps mac-notifymac-notify traps 5-6 learnedmac-notify traps 3-4 removed
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display current-configuration by-linenum show running-configuration
Common-CLI-Phase-3-Sept-2012.book Page 19 Sunday, September 9, 2012 6:00 PM
2-20
Display Commandsdisplay current-configuration configuration
display current-configuration configuration
Displays active configuration in the system excluding vlan and interface configuration. This command is available only in manager mode.
HP Switch# display current-configuration configurationhostname "HP-6200yl-24G" module 1 type J8992A alias "view" "show" banner motd "\n" radius-server host 10.10.10.1 key "abcd" ip access-list extended "grp1" exit snmp-server community "public" Unrestricted no snmpv3 enable snmpv3 enable snmpv3 group ComOperatorR user "user4" sec-model ver3 snmpv3 user "initial" snmpv3 user "user4" aaa port-access authenticator active arp-protect
Minimum Software Version: 15.10.
Comware Related ProVision
display current-configuration configuration No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 20 Sunday, September 9, 2012 6:00 PM
2-21
Display Commandsdisplay current-configuration interface
display current-configuration interface
Displays the interface configuration.
HP Switch# display current-configuration interface vlan 1 name "DEFAULT_VLAN" untagged A1-A22,F1-F24 ip address dhcp-bootp exitinterface A1 untagged vlan 1 exitinterface A2 untagged vlan 1 exitinterface A3 untagged vlan 1 exitinterface A4 untagged vlan 1 exitinterface A5 untagged vlan 1 exitinterface A6 untagged vlan 1 exitinterface A7 untagged vlan 1 exitinterface A8 untagged vlan 1 exitinterface A9 untagged vlan 1 exitinterface A10 untagged vlan 1 exitinterface A11 untagged vlan 1 exitinterface A12
Comware Related ProVision
display current-configuration interface show running-configuration
Common-CLI-Phase-3-Sept-2012.book Page 21 Sunday, September 9, 2012 6:00 PM
2-22
Display Commandsdisplay current-configuration interface
untagged vlan 1 exitinterface A13 untagged vlan 1 exitinterface A14 untagged vlan 1 exitinterface A15 untagged vlan 1 exitinterface A16 untagged vlan 1 exitinterface A17 untagged vlan 1 exitinterface A18 untagged vlan 1 exitinterface A19 untagged vlan 1
Example of Related ProVision Software Command Output.
HP Switch# show running-configRunning configuration:; J9087A Configuration Editor; Created on release #R.11.XXhostname "Switch"snmp-server community "public" Unrestrictedsnmp-server host 15.255.133.236 "public"snmp-server host 15.255.133.222 "public"snmp-server host 15.255.133.70 "public"snmp-server host 15.255.134.235 "public"vlan 1name "DEFAULT_VLAN"untagged 1-28ip address dhcp-bootpexitsnmp-server enable traps mac-notify mac-movesnmp-server enable traps mac-notify trap-interval 60snmp-server enable traps mac-notifymac-notify traps 5-6 learnedmac-notify traps 3-4 removed
For more information, see the latest Management and Configuration Guide for your switch.Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 22 Sunday, September 9, 2012 6:00 PM
2-23
Display Commandsdisplay debugging
display debugging
Displays the options from any of the following lists that have debug logging enabled.
Using display debugging without specifying an option lists all options in the set that are enabled for debug logging. For example, if acl, ip, lldp, and policy are enabled for debugging, this command produces the following:
HP Switch# display debugging ip ospf spf debugging is on acl log debugging is on lldp log debugging is on policy route-map debugging is on HP Switch#
Using display debugging with a specific option lists that option if it is enabled for debug logging. If the command returns only the CLI prompt, then the option is not enabled for debug logging. For example, if acl is enabled for debug logging and vrrp s not, this command produces the following:
HP Switch# display debugging acl log debugging is on HP Switch# display debugging vrrp HP Switch#
Operating Notes
To configure debug operation in ProVision software, use the following command.
debug < option >
For more on configuring debug operation, refer to the chapter titled “Trouble-shooting” in the latest Management and Configuration Guide for your switch.
Comware Related ProVision
display debugging [ option ] show debug [buffer [-c < count > | -r | option-str ]]
acl distributed-trunking ip lldp snmp
arp-protect dynamic-ip-lockdown ipv6 policy vrrp
cdp event lacp security
Common-CLI-Phase-3-Sept-2012.book Page 23 Sunday, September 9, 2012 6:00 PM
2-24
Display Commandsdisplay debugging
Example of Related ProVision Software Command Output.
HP Switch# show debug
Debug Logging
Source IP Selection: Outgoing Interface Destination: Memory buffer
Enabled debug types: ip ospf spf acl log lldp log policy route-map
Debug Field Mappings.
Minimum Software Version: 15.08.
Comware ProVision Software
n/a Source IP Selection
n/a Destination
debug types listed Enabled debug types
Common-CLI-Phase-3-Sept-2012.book Page 24 Sunday, September 9, 2012 6:00 PM
2-25
Display Commandsdisplay default-configuration
display default-configuration
Displays factory defaults of the switch, and all commands to be executed when the switch boots with the factory defaults.
HP Switch# display default-configuration; J8693A Configuration Editor; Created on release #K.15.09.0000x; Ver #03:01.1f.ef:f2vlan 1 name "DEFAULT_VLAN" ip address dhcp-bootp exit
Minimum Software Version: 15.10.
Comware Related ProVision
display default-configuration No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 25 Sunday, September 9, 2012 6:00 PM
2-26
Display Commandsdisplay device
display device
Displays physical modules present in the switch. This command also identifies the status of these modules, whether they are up/active/standby or failed etc.
HP Switch# display deviceSlotNo. Brd Type BrdStatus SubSlotNum SftVer PatchVerMM1 HP J9092A Management Modul... Standby n/a K.15.09.0000x n/aMM2 HP J9092A Management Modul... Active n/a K.15.09.0000x n/aSSM HP J9095A System Support M... Normal n/a K.15.09.0000x n/aFM1 HP J9093A Fabric Module 82... Enabled n/a K.15.09.0000x n/aFM2 HP J9093A Fabric Module 82... Enabled n/a K.15.09.0000x n/aA HP J9536A 20p GT PoE+/2p S... Up n/a K.15.09.0000x n/a
Field Descriptions:
Slot No.: Slot number of a card (standalone mode); slot number of a card on the specified member switch in the format of member ID/slot number (IRF mode)
Brd Type: Hardware type of a card, which can be the following values:
• Specific card model, such as LST1MRPNC1, which is the same as the silkscreen.
• NONE: No card is in the slot.
• UNKNOWN: The card is not supported by the software version and thus cannot start normally.
Brd Status: Card status, which can be the following values:
• Absent: No card is in the slot.
• Master: The card is an AMB.
• Slave: The card is an SMB.
• Normal: The card is an interface card and functions normally.
• Fault: The card has not been booted or an error occurred to the card.
• Off: The card is not powered on.
• Illegal: The card is not supported by the software version and thus cannot start normally.
Subslot Num: Number of subcards
Comware Related ProVision
display device No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 26 Sunday, September 9, 2012 6:00 PM
2-27
Display Commandsdisplay device
Sft Ver: Software version of the current card, which can be the following values:
• Specific software version: The software version of the switch.
• NONE: No card is in the slot.
• Mismatched: The software version does not support the card and thus cannot be uploaded.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 27 Sunday, September 9, 2012 6:00 PM
2-28
Display Commandsdisplay dhcp relay information all
display dhcp relay information all
Displays option 82 configuration information on the DHCP relay agent.
HP Switch# display dhcp relay information allInterface: Vlan-interface1 Status: Disable Strategy: Replace Format: Normal Circuit ID format-type: HEX Remote ID format-type: HEXInterface: Vlan-interface10 Status: Enable Strategy: Replace Format: Normal Circuit ID format-type: HEX Remote ID format-type: HEX
Minimum Software Version: 15.10.
Comware Related ProVision
display dhcp relay information all No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 28 Sunday, September 9, 2012 6:00 PM
2-29
Display Commandsdisplay dhcp relay information interface Vlan-interface <vlan-id>
display dhcp relay information interface Vlan-interface <vlan-id>
Displays option 82 configuration information on the DHCP relay agent based on vlan.
HP Switch# display dhcp relay information interface Vlan-interface 10Interface: Vlan-interface10 Status: Enable Strategy: Replace Format: Normal Circuit ID format-type: HEX Remote ID format-type: HEX
Minimum Software Version: 15.10.
Comware Related ProVision
display dhcp relay information interface Vlan-interface <vlan-id>
No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 29 Sunday, September 9, 2012 6:00 PM
2-30
Display Commandsdisplay dhcp relay statistics
display dhcp relay statistics
Displays DHCP packet statistics related to a specified or all DHCP server groups. DHCP relay statistics identifies the UDPF_DHCP_MSG PDUs and provides the information regarding the number and type of PDUs being received/relayed from/to client and server. It also distinguishes the type of packets (DISCOVER, REQUEST, INFORM, DECLINE, RELEASE, BOOTPRE-QUEST, OFFER, ACK, NAK) along with bad packets.
Comware Related ProVision
display dhcp relay statistics show dhcp-relay
Common-CLI-Phase-3-Sept-2012.book Page 30 Sunday, September 9, 2012 6:00 PM
2-31
Display Commandsdisplay dhcp relay statistics
Field Descriptions
The following fields are for bad packets received.
■ DHCP packets received from clients:• DHCPDISCOVER packets received
• DHCPREQUEST packets received
• DHCPINFORM packets received
• DHCPRELEASE packets received
• DHCPDECLINE packets received
• BOOTPREQUEST packets received
HP Switch# display dhcp relay statistics Bad packets received: 0DHCP packets received from clients: 2 DHCPDISCOVER packets received: 1 DHCPREQUEST packets received: 1 DHCPINFORM packets received: 0 DHCPRELEASE packets received: 0 DHCPDECLINE packets received: 0 BOOTPREQUEST packets received: 0DHCP packets received from servers: 2 DHCPOFFER packets received: 1 DHCPACK packets received: 1 DHCPNAK packets received: 0 BOOTPREPLY packets received: 0DHCP packets relayed to servers: 2 DHCPDISCOVER packets relayed: 1 DHCPREQUEST packets relayed: 1 DHCPINFORM packets relayed: 0 DHCPRELEASE packets relayed: 0 DHCPDECLINE packets relayed: 0 BOOTPREQUEST packets relayed: 0DHCP packets relayed to clients: 2 DHCPOFFER packets relayed: 1 DHCPACK packets relayed: 1 DHCPNAK packets relayed: 0 BOOTPREPLY packets relayed: 0DHCP packets sent to servers: n/a DHCPDISCOVER packets sent: n/a DHCPREQUEST packets sent: n/a DHCPINFORM packets sent: n/a DHCPRELEASE packets sent: n/a DHCPDECLINE packets sent: n/a BOOTPREQUEST packets sent: n/aDHCP packets sent to clients: n/a DHCPOFFER packets sent: n/a DHCPACK packets sent: n/a DHCPNAK packets sent: n/a BOOTPREPLY packets sent: n/a
Common-CLI-Phase-3-Sept-2012.book Page 31 Sunday, September 9, 2012 6:00 PM
2-32
Display Commandsdisplay dhcp relay statistics
■ DHCP packets received from servers:• DHCPOFFER packets received
• DHCPACK packets received
• DHCPNAK packets received
• BOOTPREPLY packets received
■ DHCP packets relayed to servers:• DHCPDISCOVER packets relayed
• DHCPREQUEST packets relayed
• DHCPINFORM packets relayed
• DHCPRELEASE packets relayed
• DHCPDECLINE packets relayed
• BOOTPREQUEST packets relayed
■ DHCP packets relayed to clients:• DHCPOFFER packets relayed0
• DHCPACK packets relayed
• DHCPNAK packets relayed
• BOOTPREPLY packets relayed
■ DHCP packets sent to servers:• DHCPDISCOVER packets sent
• DHCPREQUEST packets sent
• DHCPINFORM packets sent
• DHCPRELEASE packets sent
• DHCPDECLINE packets sent
• BOOTPREQUEST packets sent
■ DHCP packets sent to clients:• DHCPOFFER packets sent
• DHCPACK packets sent
• DHCPNAK packets sent
• BOOTPREPLY packets sent
Operating Notes
For more information about IPv6 DHCP, see the “DHCPv6 Relay” chapter in the latest IPv6 Configuration Guide for your switch.
Common-CLI-Phase-3-Sept-2012.book Page 32 Sunday, September 9, 2012 6:00 PM
2-33
Display Commandsdisplay dhcp relay statistics
Example of Related ProVision Software Command Output.
display dhcp relay statistics Field Mappings.
The Comware output does not correlate to the ProVision output.
Minimum Software Version: 15.09.
HP Switch(config)# show dhcp-relay DHCP Relay Agent : Enabled DHCP Request Hop Count Increment : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : replace Remote ID : mac
DHCP Relay Statistics:
Client Requests Server Responses
Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 0 0 0 0
DHCP Relay Option 82 Statistics:
Client Requests Server Responses
Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 0 0 0 0
Common-CLI-Phase-3-Sept-2012.book Page 33 Sunday, September 9, 2012 6:00 PM
2-34
Display Commandsdisplay dhcp-snooping binding database
display dhcp-snooping binding database
Displays the DHCP snooping binding file information.
HP Switch# display dhcp-snooping binding databaseFile name : cfa0:/database.dhcpUpdate interval : 10 minutesLatest read time : n/aLatest write time : Jul 15 2008 16:38:24Status : Last write succeeded.
Example of Related ProVision Software Command Output.
HP Switch# show dhcp-snoopingDHCP Snooping InformationDHCP Snooping : YesEnabled Vlans :Verify MAC : YesOption 82 untrusted policy : dropOption 82 Insertion : YesOption 82 remote-id : macStore lease database : Not configuredPort Trust----- -----B1 NoB2 No
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display dhcp-snooping binding database show dhcp-snooping
Common-CLI-Phase-3-Sept-2012.book Page 34 Sunday, September 9, 2012 6:00 PM
2-35
Display Commandsdisplay dhcp-snooping information
display dhcp-snooping information
Displays information about dhcp snooping when option 82 is enabled.
HP Switch# display dhcp-snooping information all Interface: A1 Status: Enable Strategy: Drop Format: n/a Remote ID format-type: HEX User defined : Remote ID: 0026f1-0faf00
Interface: A2 Status: Enable Strategy: Drop Format: n/a Remote ID format-type: HEX User defined: Remote ID: 0026f1-0faf00
... (contd. for all ports)
Example of Related ProVision Software Command Output.
HP Switch# show dhcp-snoopingDHCP Snooping InformationDHCP Snooping : YesEnabled Vlans :Verify MAC : YesOption 82 untrusted policy : dropOption 82 Insertion : YesOption 82 remote-id : macStore lease database : NotPort Trust----- -----B1 NoB2 No
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display dhcp-snooping information show dhcp-snooping
Common-CLI-Phase-3-Sept-2012.book Page 35 Sunday, September 9, 2012 6:00 PM
2-36
Display Commandsdisplay dhcp-snooping [ip ip_address]
display dhcp-snooping [ip ip_address]
Displays the user IP-MAC address mapping entries recorded by the DHCP snooping function.
HP Switch# display dhcp-snoopingDHCP Snooping is enabled. The client binding table for all untrusted ports. Type : D--Dynamic , S--Static , R--Recovering Type IP Address MAC Address Lease VLAN SVLAN Interface---- ----------- --------------- ---------- ---- ----- --------- S 192.168.1.1 0050-569f-2c8b static 1 n/a 1 S 192.168.1.2 0050-569f-2c8c static 2 n/a 9 S 192.168.1.3 0050-569f-2caa static 3 n/a 3 S 192.168.1.4 0050-569f-2c8a static 4 n/a 7 S 192.168.1.5 0050-569f-2c8d static 5 n/a 5 --- 5 dhcp-snooping item(s) found ---
Example of Related ProVision Software Command Output.
HP Switch# show dhcp-snooping bindingMacAddress IP VLAN Interface Time left----------------- --------------- ---- --------- ---------22.22.22.22.22.22 10.0.0.1 4 B2 1600
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display dhcp-snooping [ip ip_address] show dhcp-snooping binding
Common-CLI-Phase-3-Sept-2012.book Page 36 Sunday, September 9, 2012 6:00 PM
2-37
Display Commandsdisplay dhcp-snooping packet statistics
display dhcp-snooping packet statistics
Displays the statistics of the dhcp snooping packets.
HP Switch# display dhcp-snooping packet statistics DHCP packets received : 2 DHCP packets send : 0 Packets dropped due to rate limitation : n/a Dropped invalid packets : 0
Example of Related ProVision Software Command Output.
HP Switch# show dhcp-snooping statistics
Packet type Action Reason Count
----------- ------- ---------------------------- ---------
server forward from trusted port 0
client forward to trusted port 0
server drop received on untrusted port 0
server drop unauthorized server 0
client drop destination on untrusted port 0
client drop untrusted option 82 field 0
client drop bad DHCP release request 0
client drop failed verify MAC check 0
Minimum Software Version: 15.10.
Comware Related ProVision
display dhcp-snooping packet statistics show dhcp-snooping statistics
Common-CLI-Phase-3-Sept-2012.book Page 37 Sunday, September 9, 2012 6:00 PM
2-38
Display Commandsdisplay dhcp-snooping trust
display dhcp-snooping trust
Displays information about trusted ports.
Field Descriptions
Interface: Interface
Trusted: The interface is trusted or not trusted.
Operating Notes
For more information about DHCP snooping, see the “Configuring Advanced Threat Protection” chapter in the latest Access Security Guide for your switch.
Comware Related ProVision
display dhcp-snooping trust show dhcp-snooping
HP Switch(config)# display dhcp-snooping trust
DHCP Snooping is enabled.DHCP Snooping trust becomes active. Interface Trusted ========================= ============ A1 Trusted A2 Trusted A3 Trusted A4 Trusted
Common-CLI-Phase-3-Sept-2012.book Page 38 Sunday, September 9, 2012 6:00 PM
2-39
Display Commandsdisplay dhcp-snooping trust
Example of Related ProVision Software Command Output.
display dhcp-snooping trust Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
DHCP snooping is enabled DHCP Snooping (yes/no)
Interface Port
Trusted Trust
HP Switch(config)# show dhcp-snooping
DHCP Snooping Information
DHCP Snooping : Yes
Enabled Vlans :
Verify MAC : Yes
Option 82 untrusted policy : drop
Option 82 Insertion : Yes
Option 82 remote-id : mac
Store lease database : Not configured
Port Trust
----- -----
B1 No
B2 No
Common-CLI-Phase-3-Sept-2012.book Page 39 Sunday, September 9, 2012 6:00 PM
2-40
Display Commandsdisplay diagnostic-information
display diagnostic-information
Displays different levels of diagnostic information. This is an alias to the ProVision command show tech and shares the same behavior.
HP Switch# show tech
show system
Status and Counters - General System InformationSystem Name : 5400_1System Contact :System Location :
MAC Age Time (sec) : 300
Time Zone : 0Daylight Time Rule : None
Software revision : K.14.XX Base MAC Addr : 001871-c42f00ROM Version : K.12.12 Serial Number : SG641SU00L
Up Time : 23 hours Memory - Total :CPU Util (%) : 10 Free :IP Mgmt - Pkts Rx : 759 Packet - Total : 6750Pkts Tx : 2 Buffers Free : 5086Lowest : 4961Missed : 0show flashImage Size(Bytes) Date Version----- ---------- -------- -----------
Minimum Software Version: 15.10.
Comware Related ProVision
display diagnostic-information show tech
Common-CLI-Phase-3-Sept-2012.book Page 40 Sunday, September 9, 2012 6:00 PM
2-41
Display Commandsdisplay dns domain
display dns domain
Displays all the domain name suffixes that are appended to host names by the resolver before sending the queries to name servers. These domain name suffixes could have been statically configured on the switch or obtained from the DHCP server dynamically.
HP Switch# display dns domain Type: D:Dynamic S:Static
No. Type Domain-name1 S hp5.com2 S hp.in3 S hp.us
Example of Related ProVision Software Command Output.
HP Switch# show ip dnsDNS Mode : DHCPDomain Suffix : pubs.outdoors.com
DNS Servers Configured:----------------------10.28.229.10
Priority DNS Server Addresses-------- --------------------1 10.28.192.1
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display dns domain show ip dns
Common-CLI-Phase-3-Sept-2012.book Page 41 Sunday, September 9, 2012 6:00 PM
2-42
Display Commandsdisplay dns domain dynamic
display dns domain dynamic
Displays all the domain name suffixes that are obtained from the DHCP server dynamically.
HP Switch# display dns domain dynamic
Type: D:Dynamic S:Static
No. Type Domain-name1 D hp2.net2 D hp3.net3 D hp4.net
Minimum Software Version: 15.10.
Comware Related ProVision
display dns domain dynamic No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 42 Sunday, September 9, 2012 6:00 PM
2-43
Display Commandsdisplay dns < domain | server >
display dns < domain | server >
Displays the current IPv4 DNS domain name suffixes and server configuration.
HP Switch# display dns domain Type: D:Dynamic S:Static
No. Type Domain-name 1 S atlantic.widgetcorp.net
HP Switch# display dns server
Type: D:Dynamic S:Static
DNS Server Type IP Address 1 S 10.110.34.51 2 S 10.110.34.101
Field Descriptions
No.: Sequence number.
Type: Shows the type of domain name suffix. S means a statically configured domaine name suffix. D means a domain name suffix obtained dynamically through DHCP.
Domain-name: The domain name suffix.
DNS Server: The sequence number of the DNS server.
IP Address: The IPv4 address of the DNS server(s).
Operating Notes
The switch supports one domain suffix entry and two DNS server IP address entries.
To configure DNS operation in ProVision software, use one of the following commands.
Comware Related ProVision
display dns < domain | server > show ip dns show ip
Common-CLI-Phase-3-Sept-2012.book Page 43 Sunday, September 9, 2012 6:00 PM
2-44
Display Commandsdisplay dns < domain | server >
ip dns dhcp ip dns domain-name < name-str > ip dns server-address priority < 1 | 2 > < ip-addr | ipv6-addr >
For more on configuring dns, refer to the “Troubleshooting” chapter in the latest Management and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch# show ip dns
DNS Mode : DHCP Domain Suffix : americas.hpqcorp.net
DNS Servers Configured: ---------------------- Priority DNS Server Addresses -------- -------------------- 1. 16.110.135.52 2. 16.110.135.51
DNS Field Mappings.
Minimum Software Version: 15.08.
Comware ProVision Software
No. n/a
DNS Server Priority
Type DNS Mode
Domain-name Domain Suffix
IP Address DNS Server Addresses
n/a DNS Servers Configured
Common-CLI-Phase-3-Sept-2012.book Page 44 Sunday, September 9, 2012 6:00 PM
2-45
Display Commandsdisplay dns ipv6 server
display dns ipv6 server
Displays IPv6 DNS server information.
Field Descriptions
DNS Server: Sequence number of the DNS server, which is assigned automat-ically by the system, starting from 1.
Type: Type of the DNS server. “S” represents a statically configured DNS server, and “D” represents a DNS server obtained dynamically through DHCP or other protocols.
IPv6 Address: IPv6 address of the DNS server.
Interface Name: Interface name, which is available only for a DNS server with an IPv6 link-local address configured.
Operating Notes
Out-of-band management and tunnel interfaces are supported.
For more information about IPv6 DNS, see the “IPv6 Diagnostic and Trouble-shooting” chapter in the latest IPv6 Configuration Guide for your switch.
Comware Related ProVision
display dns ipv6 server show ip dns
HP Switch# display dns ipv6 server Type: D:Dynamic S:Static
DNS Server Type IPv6 Address (Interface Name) 1 S 1::1 2 S FE80:1111:2222:3333:4444:5555:6666:7777 Vlan2
Common-CLI-Phase-3-Sept-2012.book Page 45 Sunday, September 9, 2012 6:00 PM
2-46
Display Commandsdisplay dns ipv6 server
Example of Related ProVision Software Command Output.
display dns ipv6 server Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
DNS Server DNS Servers Configured
Type DNS Mode
IPv6 Address DNS Server Addresses
Interface Name n/a
HP Switch(config)# show ip dns
DNS Mode : Manual Domain Suffix : atlantic.widgetcorp.net DNS Servers Configured: ----------------------
Priority DNS Server Addresses -------- -------------------- 1. 10.110.34.51 2. 10.110.34.101
Common-CLI-Phase-3-Sept-2012.book Page 46 Sunday, September 9, 2012 6:00 PM
2-47
Display Commandsdisplay dot1x [interface]
display dot1x [interface]
Displays information about 802.1X.
If you specify neither the sessions keyword nor the statistics keyword, the command displays all information about 802.1X, including session informa-tion, statistics, and configurations.
Comware Related ProVision
display dot1x [interface interface-list]display dot1x sessions [interface interface-list]display dot1x statistics [interface interface-list]
show port-access authenticator [config | statistics | session counters]
Common-CLI-Phase-3-Sept-2012.book Page 47 Sunday, September 9, 2012 6:00 PM
2-48
Display Commandsdisplay dot1x [interface]
HP Switch(config)# display dot1x interface A1
Equipment 802.1X protocol is CHAP authentication is n/a Proxy trap checker is n/a Proxy logoff checker is n/a EAD quick deploy is n/a
Configuration: Transmit Period 30 s, Handshake Period n/a Quiet Period 60 s, Quiet Period Timer is n/a Supp Timeout 30 s, Server Timeout 300 s Reauth Period 3600 s The maximal retransmitting times 2 EAD quick deploy configuration: EAD timeout: n/a
The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a
A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Periodic reauthentication is disabled The port is not an authenticator Authentication Mode is Auto Port Control Type is n/a 802.1X Multicast-trigger is n/a Mandatory authentication domain: n/a Guest VLAN: 0 Auth-Fail VLAN: n/a Max number of on-line users is 0
EAPOL Packet: Tx n/a, Rx n/a Sent EAP Request/Identity Packets : 0 EAP Request/Challenge Packets: 0 EAP Request/Challenge Packets: 0 Received EAPOL Start Packets : 0 EAPOL LogOff Packets: 0 EAP Response/Identity Packets : 0 EAP Response/Challenge Packets: 0 Error Packets: 0
Controlled User(s) amount to n/a
Common-CLI-Phase-3-Sept-2012.book Page 48 Sunday, September 9, 2012 6:00 PM
2-49
Display Commandsdisplay dot1x [interface]
HP Switch(config)# display dot1x sessions
Equipment 802.1X protocol is enabled CHAP authentication is n/a
The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a
A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a
Controlled User(s) amount to n/a
A2 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a
Controlled User(s) amount to n/a
A3 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a
Controlled User(s) amount to n/a
Common-CLI-Phase-3-Sept-2012.book Page 49 Sunday, September 9, 2012 6:00 PM
2-50
Display Commandsdisplay dot1x [interface]
HP Switch(config)# display dot1x statistics Equipment 802.1X protocol is enabled CHAP authentication is n/a
The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a
A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a
EAPOL Packet: Tx n/a, Rx n/a Sent EAP Request/Identity Packets : 0 EAP Request/Challenge Packets: 0 EAP Request/Challenge Packets: 0 Received EAPOL Start Packets : 0 EAPOL LogOff Packets: 0 EAP Response/Identity Packets : 0 EAP Response/Challenge Packets: 0 Error Packets: 0
Controlled User(s) amount to n/a
A2 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a
EAPOL Packet: Tx n/a, Rx n/a Sent EAP Request/Identity Packets : 0 EAP Request/Challenge Packets: 0 EAP Request/Challenge Packets: 0 Received EAPOL Start Packets : 0 EAPOL LogOff Packets: 0 EAP Response/Identity Packets : 0 EAP Response/Challenge Packets: 0 Error Packets: 0
Controlled User(s) amount to n/a
Common-CLI-Phase-3-Sept-2012.book Page 50 Sunday, September 9, 2012 6:00 PM
2-51
Display Commandsdisplay dot1x [interface]
Field Descriptions
Equipment 802.1X protocol is enabled: Specifies whether 802.1X is enabled globally.
CHAP authentication is enabled: Specifies whether CHAP authentication is enabled.
Transmit Period: Username request timeout timer in seconds.
Handshake Period: Handshake timer in seconds.
Reauth Period: Periodic re-authentication timer in seconds.
Quiet Period: Quiet timer in seconds.
Quiet Period Timer is disabled: Status of the quiet timer. In this example, the quiet timer is enabled.
Supp Timeout: Client timeout timer in seconds.
Server Timeout: Server timeout timer in seconds.
The maximal retransmitting times: Maximum number of attempts for sending an authentication request to a client.
The maximum 802.1X user resource number per slot: Maximum number of concur-rent 802.1X user per card.
Total current used 802.1X resource number: Total number of online 802.1X users.
GigabitEthernet3/0/1 is link-up: Status of the port. In this example, GigabitEth-ernet 3/0/1 is up.
802.1X protocol is disabled: Specifies whether 802.1X is enabled on the port.
Handshake is disabled: Specifies whether handshake is enabled on the port.
Handshake secure is disabled: Specifies whether handshake security is enabled on the port.
802.1X unicast-trigger is disabled: Specifies whether unicast trigger is enabled on the port.
Periodic reauthentication is disabled: Specifies whether periodic online user re-authentication is enabled on the port.
The port is an authenticator: Role of the port.
Common-CLI-Phase-3-Sept-2012.book Page 51 Sunday, September 9, 2012 6:00 PM
2-52
Display Commandsdisplay dot1x [interface]
Authenticate Mode is Auto: Authorization state of the port.
Port Control Type is Mac-based: Access control method of the port.
802.1X Multicast-trigger is enabled: Specifies whether the 802.1X multicast-trigger function is enabled.
Mandatory authentication domain: Mandatory authentication domain on the port.
Guest VLAN: 802.1X guest VLAN configured on the port. NOT configured is displayed if no guest VLAN is configured.
Auth-fail VLAN: Auth-Fail VLAN configured on the port. NOT configured is displayed if no Auth-Fail VLAN is configured.
Max number of on-line users: Maximum number of concurrent 802.1X users on the port.
EAPOL Packet: Number of sent (Tx) and received (Rx) EAPOL packets.
Sent EAP Request/Identity Packets: Number of sent EAP-Request/Identity pack-ets.
EAP Request/Challenge Packets: Number of sent EAP-Request/Challenge pack-ets.
EAP Success Packets: Number of sent EAP Success packets.
Fail Packets: Number of sent EAP-Failure packets.
Received EAPOL Start Packets: Number of received EAPOL-Start packets.
EAPOL LogOff Packets: Number of received EAPOL-LogOff packets.
EAP Response/Identity Packets: Number of received EAP-Response/Identity packets.
EAP Response/Challenge Packets: Number of received EAP-Response/Chal-lenge packets.
Error Packets: Number of received error packets.
Controlled User(s) amount: Number of authenticated users on the port.
Common-CLI-Phase-3-Sept-2012.book Page 52 Sunday, September 9, 2012 6:00 PM
2-53
Display Commandsdisplay dot1x [interface]
Operating Notes
For more on switch 802.1X operation, refer to the “Configuring Port-based and User-based Access Control (802.1X)” chapter in the latest Access Security
Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show port-access authenticator config
Port Access Authenticator Configuration
Port-access authenticator activated [No] : Yes Allow RADIUS-assigned dynamic (GVRP) VLANs [No] : No | Re-auth Access Max Quiet TX Supplicant Server Cntrl Port | Period Control Reqs Period Timeout Timeout Timeout Dir ---- + ------- -------- ----- ------- -------- ---------- -------- ----- 1 | No Auto 2 60 30 30 30 both 2 | No Auto 2 60 30 30 30 in ...
HP Switch(config)# show port-access authenticator session-counters
Port Access Authenticator Session Counters
Port-access authenticator activated [No] : Yes Allow RADIUS-assigned dynamic (GVRP) VLANs [No] : No Session Session Port Frames In Frames Out Time(sec.) Status User ---- ---------- ----------- ----------- ----------- ------- 2 45623 45623 20 in-progress bert
Common-CLI-Phase-3-Sept-2012.book Page 53 Sunday, September 9, 2012 6:00 PM
2-54
Display Commandsdisplay dot1x [interface]
display dot1x Field Mappings.
HP Switch(config)# show port-access authenticator statistics
Port Access Authenticator Statistics
Port-access authenticator activated [No] : Yes Allow RADIUS-assigned dynamic (GVRP) VLANs [No] : No
Source TX TX RX RX RX RX RX Port MAC address ReqId Req Start Logoff RespId Resp Errors ---- ------------- ------ ----- ------ ------- ------- ----- ------- 2 001560-b3ea48 1 0 0 0 0 0 0
Comware ProVision Software
Equipment 802.1X protocol is enabled Port-access authenticator activated (yes/no)
CHAP authentication is enabled n/a
Transmit Period TX Timeout
Handshake Period n/a
Reauth Period Re-auth Period
Quiet Period Quiet Period
Quiet Period Timer is disabled n/a
Supp Timeout Supplicant Timeout
Server Timeout Server Timeout
The maximal retransmitting times Max Reqs
The maximum 802.1X user resource number per slot
n/a
Total current used 802.1X resource number n/a
GigabitEthernet3/0/1 is link up n/a
802.1X protocol is disabled Port-access authenticator activated (yes/no)
Handshake is disabled n/a
802.1X unicast-trigger is disabled n/a
Common-CLI-Phase-3-Sept-2012.book Page 54 Sunday, September 9, 2012 6:00 PM
2-55
Display Commandsdisplay dot1x [interface]
Minimum Software Version: 15.09.
Periodic reauthentication is disabled Re-auth Period
The port is an authenticator n/a
Authenticate Mode is Auto Access Control
Port Control Type is Mac-based n/a
802.1X Multicast-trigger is enabled n/a
Mandatory authentication domain n/a
Guest VLAN n/a
Auth-fail VLAN n/a
Max number of on-line users n/a
EAPOL Packet n/a
Sent EAP Request/Identity Packets TX ReqId
EAP Request/Challenge Packets TX Req
EAP Success Packets n/a
Fail Packets n/a
Received EAPOL Start Packets RX Start
EAPOL Logoff Packets RX Logoff
EAP Response/Identity Packets RX RespId
EAP Response/Challenge Packets RX Resp
Error Packets RX Errors
Controlled User(s) amount n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 55 Sunday, September 9, 2012 6:00 PM
2-56
Display Commandsdisplay dot1x [interface …]
display dot1x [interface …]display dot1x sessions [interface …]display dot1x statistics [interface …]
Displays information about 802.1X.
HP Switch# display dot1xEquipment 802.1X protocol is CHAP authentication is n/a Proxy trap checker is n/a Proxy logoff checker is n/a EAD quick deploy is n/a Configuration: Transmit Period 30 s, Handshake Period n/a Quiet Period 60 s, Quiet Period Timer is n/a Supp Timeout 30 s, Server Timeout 300 s Reauth Period 3600 s The maximal retransmitting times 2 EAD quick deploy configuration: EAD timeout: n/a The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Periodic reauthentication is disabled The port is not an authenticator Authentication Mode is Auto Port Control Type is n/a 802.1X Multicast-trigger is n/a Mandatory authentication domain: n/a Guest VLAN: 0 Auth-Fail VLAN: n/a Max number of on-line users is 0 EAPOL Packet: Tx n/a, Rx n/a Sent EAP Request/Identity Packets : 0
Comware Related ProVision
display dot1x [interface ...]display dot1x sessions [interface ...]display dot1x statistics [interface ...]
show dhcp-snooping binding
Common-CLI-Phase-3-Sept-2012.book Page 56 Sunday, September 9, 2012 6:00 PM
2-57
Display Commandsdisplay dot1x statistics [interface …]
EAP Request/Challenge Packets: 0 EAP Request/Challenge Packets: 0 Received EAPOL Start Packets : 0 EAPOL LogOff Packets: 0 EAP Response/Identity Packets : 0 EAP Response/Challenge Packets: 0 Error Packets: 0 Controlled User(s) amount to n/a
HP Switch# display dot1x sessions Equipment 802.1X protocol is enabled CHAP authentication is n/a The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Controlled User(s) amount to n/a A2 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Controlled User(s) amount to n/a A3 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Controlled User(s) amount to n/a
HP Switch# display dot1x sessionsEquipment 802.1X protocol is enabled CHAP authentication is n/a The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a
Common-CLI-Phase-3-Sept-2012.book Page 57 Sunday, September 9, 2012 6:00 PM
2-58
Display Commandsdisplay dot1x statistics [interface …]
Handshake secure is n/a 802.1X unicast-trigger is n/a EAPOL Packet: Tx n/a, Rx n/a Sent EAP Request/Identity Packets : 0 EAP Request/Challenge Packets: 0 EAP Request/Challenge Packets: 0 Received EAPOL Start Packets : 0 EAPOL LogOff Packets: 0 EAP Response/Identity Packets : 0 EAP Response/Challenge Packets: 0 Error Packets: 0 Controlled User(s) amount to n/a A2 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a EAPOL Packet: Tx n/a, Rx n/a Sent EAP Request/Identity Packets : 0 EAP Request/Challenge Packets: 0 EAP Request/Challenge Packets: 0 Received EAPOL Start Packets : 0 EAPOL LogOff Packets: 0 EAP Response/Identity Packets : 0 EAP Response/Challenge Packets: 0 Error Packets: 0 Controlled User(s) amount to n/a
Example of Related ProVision Software Command Output.
HP Switch# show dhcp-snooping binding
MacAddress IP VLAN Interface Time left----------------- -------- ----- --------- ---------22.22.22.22.22.22 10.0.0.1 4 B2 1600
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 58 Sunday, September 9, 2012 6:00 PM
2-59
Display Commandsdisplay environment
display environment
Displays the temperature information, including the current temperature and temperature thresholds of cards.
HP Switch# display environmentSystem temperature information (degree centigrade)---------------------------------------------------------Slot Sensor Temperature LowerLimit WarningLimit AlarmLimit ShutdownLimitn/a Sys-1 29C n/a 57C n/a n/a
Field Descriptions:
Slot: Slot number of the card (standalone mode); slot number of a card on the specified member switch in the format of member ID/slot number (IRF mode)
Sensor: Temperature sensor:
• hotspot: Hotspot temperature sensor
• inflow: Inflow temperature sensor
• outflow: Outflow temperature sensor
Temperature: Current temperature
Lower limit: Lower limit of temperature
WarningLimit: Upper limit of temperature for warning
AlarmLimit: Upper limit of temperature for alarming
ShutdownLimit: Upper limit of temperature for shutting down the switch (currently not supported)
Example of Related ProVision Software Command Output.
HP Switch# show system temperature
System Air Temperatures
# |Current Temp | Max Temp | Min Temp | Threshold | OverTemp------+------------+----------+---------+-----------+--------Sys-1 | 31C | 37C | 29C | 57C | NO
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display environment show system temperature
Common-CLI-Phase-3-Sept-2012.book Page 59 Sunday, September 9, 2012 6:00 PM
2-60
Display Commandsdisplay fan
display fan
Displays the operating state of built-in fans.
HP Switch# display fanFan 1 State: Fan Ok
Example of Related ProVision Software Command Output.
HP Switch(config)# show system fansFan InformationNum | State | Failures-------+-------------+----------Sys-1 | Fan OK | 00 / 1 Fans in Failure State0 / 1 Fans have been in Failure State
Operating Notes
ProVision uses HP format for printing the fan state.
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display fan show system fans
Common-CLI-Phase-3-Sept-2012.book Page 60 Sunday, September 9, 2012 6:00 PM
2-61
Display Commandsdisplay fips status
display fips status
Displays FIPS state. By default, the FIPS mode is disabled.
HP Switch# display fips status
FIPS mode is disabled
or
HP Switch# display fips status
FIPS mode is enabled
Example of Related ProVision Software Command Output.
HP Switch# show secure-mode
Level: Standard
or
HP Switch# show secure-mode
Level: Enhanced
For more information, see the latest Access Security Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display fips status show secure-mode
Common-CLI-Phase-3-Sept-2012.book Page 61 Sunday, September 9, 2012 6:00 PM
2-62
Display Commandsdisplay garp statistics interface <port_list>
display garp statistics interface <port_list>
Displays GVRP transmitted, received and discarded frames in a specified VLAN on a port.
HP Switch# display garp statistics interface a2
GARP statistics on port A2 Number of GVRP Frames Received : 79 Number of GVRP Frames Transmitted : 67 Number of Frames Discarded : 0
Example of Related ProVision Software Command Output.
HP Switch# show gvrp
GVRP support
Maximum VLANs to support [256] : 256Primary VLAN : DEFAULT_VLANGVRP Enabled [No] : Yes
Port Type | Unknown VLAN Join Leave Leaveall---- -------- + ------------ ----- ----- --------1 10/100TX | Learn 20 300 10002 10/100TX | Learn 20 300 10003 10/100TX | Learn 20 300 10004 10/100TX | Learn 20 300 10005 10/100TX | Learn 20 300 10006 10/100TX | Learn 20 300 1000. . . . . .
For more information, see the latest Advanced Traffic Management Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display garp statistics interface <port_list> show gvrp
Common-CLI-Phase-3-Sept-2012.book Page 62 Sunday, September 9, 2012 6:00 PM
2-63
Display Commandsdisplay garp timer interface <port_list>
display garp timer interface <port_list>
Display GARP timer in a specified port.
HP Switch# display garp timer interface a2
GARP timers on port A2 Garp Join Time : 20 centisecounds Garp Leave Time : 300 centisecounds Garp LeaveAll Time : 1000 centisecounds Garp Hold Time : (n/a)
Example of Related ProVision Software Command Output.
HP Switch# show gvrp
GVRP support
Maximum VLANs to support [256] : 256Primary VLAN : DEFAULT_VLANGVRP Enabled [No] : Yes
Port Type | Unknown VLAN Join Leave Leaveall---- -------- + ------------ ----- ----- --------1 10/100TX | Learn 20 300 10002 10/100TX | Learn 20 300 10003 10/100TX | Learn 20 300 10004 10/100TX | Learn 20 300 10005 10/100TX | Learn 20 300 10006 10/100TX | Learn 20 300 1000. . . . . .
Operating Notes
Depending on the device, ProVision displays port numbers as A1, B1, etc. or 1,2, etc. or 1/1, 2/1, etc.
Any display output field not supported in Provsion is displayed as n/a.
For more information, see the latest Advanced Traffic Management Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display garp timer interface<port_list> show gvrp
Common-CLI-Phase-3-Sept-2012.book Page 63 Sunday, September 9, 2012 6:00 PM
2-64
Display Commandsdisplay gvrp state interface <port_list> vlan <vlan-id>
display gvrp state interface <port_list> vlan <vlan-id>
Displays GVRP state machines in a specified VLAN on a port.
HP Switch# display gvrp state interface a2 vlan 2
GVRP state of VLAN 2 on port a2 Applicant state machine : QA Registrar state machine : MTR
Field Descriptions:
Applicant state machine: The Applicant state machine handles attribute decla-rations. Its state can be VA, AA, QA, LA, VP, AP, QP, VO, AO, QO, LO, VON, AON, and QON. Each state consists of two or three letters with the following meanings:
• The first letter indicates the state: V for Very anxious, A for Anxious, Q for Quiet, and L for Leaving.
• The second letter indicates the membership state: A for Active mem-ber, P for Passive member, O for Observer.
• The third letter N (if any) stands for Non-participant.
For example, VP indicates “Very anxious, Passive member".
Registrar state machine: The Registrar state machine records the registration of attributes declared by other participants. Its state can be INN, LV, L3, L2, L1, MT, INR, LVR, L3R, L2R, L1R, MTR, INF, LVF, L3F, L2F, L1F, and MTF. Each state consists of two or three letters/numbers with the following meanings:
• The first two letters/numbers indicate the state: IN stands for In; LV, L3, L2, and L1 all stand for Leaving, and L3, L2, L1 are three sub-states of LV; MT stands for Empty
• The third letter indicates the registration mode: N (or the third letter being absent) for normal registration, R for Registration fixed, and F for Registration forbidden.
For example, MTR stands for “Empty, Registration fixed", indicating the fixed registration mode in Empty state.
Comware Related ProVision
display gvrp state interface <port_list> vlan <vlan-id>
show gvrp
Common-CLI-Phase-3-Sept-2012.book Page 64 Sunday, September 9, 2012 6:00 PM
2-65
Display Commandsdisplay gvrp state interface <port_list> vlan <vlan-id>
Example of Related ProVision Software Command Output.
HP Switch# show gvrp
GVRP support
Maximum VLANs to support [256] : 256Primary VLAN : DEFAULT_VLANGVRP Enabled [No] : Yes
Port Type | Unknown VLAN Join Leave Leaveall---- -------- + ------------ ----- ----- --------1 10/100TX | Learn 20 300 10002 10/100TX | Learn 20 300 10003 10/100TX | Learn 20 300 10004 10/100TX | Learn 20 300 10005 10/100TX | Learn 20 300 10006 10/100TX | Learn 20 300 1000. . . . . .
For more information, see the latest Advanced Traffic Management Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 65 Sunday, September 9, 2012 6:00 PM
2-66
Display Commandsdisplay gvrp statistics
display gvrp statistics
Displays the GVRP statistics of all tagged ports.
HP Switch# display gvrp statistics GVRP statistics on port A1 GVRP Status : Disabled GVRP Running : YES GVRP Failed Registrations : n/a GVRP Last Pdu Origin : n/a GVRP Registration Type : Normal
Field Descriptions:
GVRP Status: Indicates whether GVRP is enabled or disabled
GVRP Running: Indicates whether GVRP is running
GVRP Failed Registrations: Indicates the number of GVRP registration failures
GVRP Last Pdu Origin: Indicates the source MAC address in the last GVRP PDU
GVRP Registration Type: Indicates the GVRP registration mode (fixed, forbid-den, or normal) on the port
Example of Related ProVision Software Command Output.
HP Switch# show gvrp GVRP support Maximum VLANs to support [256] : 256Primary VLAN : DEFAULT_VLANGVRP Enabled [No] : Yes
Port Type | Unknown VLAN Join Leave Leaveall---- -------- + ------------ ----- ----- --------1 10/100TX | Learn 20 300 10002 10/100TX | Learn 20 300 10003 10/100TX | Learn 20 300 10004 10/100TX | Learn 20 300 10005 10/100TX | Learn 20 300 10006 10/100TX | Learn 20 300 1000. . . . . .For more information, see the latest Advanced Traffic Management Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display gvrp statistics show gvrp
Common-CLI-Phase-3-Sept-2012.book Page 66 Sunday, September 9, 2012 6:00 PM
2-67
Display Commandsdisplay gvrp status
display gvrp status
Displays the global enable/disable state of GVRP.
HP Switch# display gvrp status
GVRP is enabled
Operating Notes
To enable and control GVRP operation in ProVision software, use the follow-ing commands:
gvrp
interface < port-list > unknown-vlans < learn | block | disable >
ProVision software also supports GVRP configuration and status monitoring by using the Menu interface. For more on GVRP operation, refer to the chapter titled “GVRP” in the latest Advanced Traffic Management Guide for your switch.
Example of Related ProVision Software Command Output.
GVRP disabled:
HP Switch# show gvrp
GVRP support
Maximum VLANs to support [256] : 256 Primary VLAN : DEFAULT_VLAN GVRP Enabled [No] : No
GVRP enabled:
HP Switch# show gvrp
GVRP support
Maximum VLANs to support [256] : 256 Primary VLAN : DEFAULT_VLAN GVRP Enabled [No] : Yes
Comware Related ProVision
display gvrp status show gvrp
Common-CLI-Phase-3-Sept-2012.book Page 67 Sunday, September 9, 2012 6:00 PM
2-68
Display Commandsdisplay gvrp status
Port Type | Unknown VLAN Join Leave Leaveall ---- --------- + ------------ ----- ----- -------- A1 100/1000T | Learn 20 300 1000 A2 100/1000T | Learn 20 300 1000 A3 100/1000T | Learn 20 300 1000 . . . A24 100/1000T | Learn 20 300 1000
Minimum Software Version: 15.08.
Common-CLI-Phase-3-Sept-2012.book Page 68 Sunday, September 9, 2012 6:00 PM
2-69
Display Commandsdisplay gvrp vlan-operation interface interface-type interface-number
display gvrp vlan-operation interface interface-type interface-number
Displays information about dynamic VLAN operations on a port.
HP Switch# display gvrp vlan-operation interface a3
Dynamic VLAN operations on port A3
Operations of creating VLAN : none Operations of deleting VLAN : none Operations of adding VLAN to TRUNK : none Operations of deleting VLAN from TRUNK : none
Minimum Software Version: 15.10.
Comware Related ProVision
display gvrp vlan-operation interface interface-type interface-number
No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 69 Sunday, September 9, 2012 6:00 PM
2-70
Display Commandsdisplay history-command
display history-command
Displays the last 25 commands executed on the switch CLI, including commands entered incorrectly. The command listing begins with the oldest command in the sequence and ends with the most recent command executed (excluding the display history-command itself).
HP Switch# display history-command 25 display dns domain 24 display gvrp status 23 display gvrp status 22 gvrp helpp 21 gvrp help 20 gvrp 19 display gvrp status . . . 2 display ip community-list 1 display ip as-path
Operating Notes
The ProVision software show history command output is identical to the Com-ware display history-command output.
Minimum Software Version: 15.08.
Comware Related ProVision
display history-command show history
Common-CLI-Phase-3-Sept-2012.book Page 70 Sunday, September 9, 2012 6:00 PM
2-71
Display Commandsdisplay hwtacacs
display hwtacacs
Displays the configuration information or statistics of HWTACACS schemes. This command is available only in manager mode.
HP Switch# display hwtacacs
------------------------------------------------------------- HWTACACS-server template name : n/a Primary-authentication-server : 1.2.3.4:n/a VPN instance : n/a Primary-authorization-server : 1.2.3.4:n/a VPN instance : n/a Primary-accounting-server : 1.2.3.4:n/a VPN instance : n/a Secondary-authentication-server : 6.7.8.9:n/a VPN instance : n/a Secondary-authorization-server : 6.7.8.9:n/a VPN instance : n/a Secondary-accounting-server : 6.7.8.9:n/a VPN instance : n/a Current-authentication-server : 1.2.3.4:n/a VPN instance : n/a Current-authorization-server : 1.2.3.4:n/a VPN instance : n/a Current-accounting-server : 1.2.3.4:n/a VPN instance : n/a Nas-IP address : n/a key authentication : authentication key authorization : authentication key accounting : authentication Nas-IP address : n/a VPN instance : n/a Quiet-interval(min) : n/a Realtime-accounting-interval(min) : n/a Response-timeout-interval(sec) : 5 Acct-stop-PKT retransmit times : n/a Username format : n/a Data traffic-unit : n/a Packet traffic-unit : n/a------------------------------------------------------------- Total 1 HWTACACS scheme(s).
Comware Related ProVision
display hwtacacs show tacacs
Common-CLI-Phase-3-Sept-2012.book Page 71 Sunday, September 9, 2012 6:00 PM
2-72
Display Commandsdisplay hwtacacs
Example of Related ProVision Software Command Output.
HP Switch# show tacacs
Status and Counters - TACACS Information
Timeout : 5Source IP Selection : Configured IP InterfaceEncryption Key :
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 72 Sunday, September 9, 2012 6:00 PM
2-73
Display Commandsdisplay igmp group
display igmp group
Displays IGMP group address, uptime, and expiry information. If no IGMP groups are detected, returns the system prompt.
HP Switch# display igmp group Total 1 IGMP Group(s). Interface group report information Vlan-interface1(15.255.134.111): Total 1 IGMP Group reported Group Address Last Reporter UpTime Expires 10.255.215.190 10.125.103.197 00:04:22 00:03:38
Field Descriptions
Vlan-interfaceN: IP address of a VLAN on which IGMP is running.
Group Address: Multicast group address.
Last Reporter: Address of the last host that reported its membership for this multicast group.
UpTime: Length of time since the multicast group was reported.
Expires: Remaining time of the multicast group, where “off” means that the multicast group never times out.
Operating Notes
To enable IGMP operation in ProVision software, use the following command from the context of a VLAN on which you want to enable IGMP:
ip igmp
For more on IGMP operation in ProVision software, refer to the chapter titled “Multimedia Traffic Control with IP Multicast (IGMP)” in the latest Multicast
and Routing Guide for your switch.
Comware Related ProVision
display igmp group show ip igmp groups
Common-CLI-Phase-3-Sept-2012.book Page 73 Sunday, September 9, 2012 6:00 PM
2-74
Display Commandsdisplay igmp group
Example of Related ProVision Software Command Output.
IGMP Field Mappings.
Minimum Software Version: 15.08.
HP Switch# show ip igmp groups
IGMP Group Address Information
VLAN ID Group Address Expires UpTime Last Reporter | Type ------- --------------- ------------- ------------- --------------- + ------ 1 10.255.215.190 0h 0m 27s 1h 22m 37s 10.125.103.197 | Filter
Comware ProVision Software
Vlan-interfaceN VLAN ID
Group Address Group Address
Expires Expires
Uptime UpTime
Last Reporter Last Reporter
n/a Type
Common-CLI-Phase-3-Sept-2012.book Page 74 Sunday, September 9, 2012 6:00 PM
2-75
Display Commandsdisplay igmp group interface vlan-interface <vlan-id>
display igmp group interface vlan-interface <vlan-id>
Displays information about dynamically joined IGMP multicast groups.
HP Switch# display igmp group interface vlan-interface 30Vlan-interface30(75.1.30.1): Total 5 IGMP Groups reported Group Address Last Reporter UpTime Expires 239.1.1.1 75.1.30.10 5d 17:48:41 00:03:13 239.1.1.2 75.1.30.10 5d 17:48:41 00:03:13 239.1.1.3 75.1.30.10 5d 17:48:41 00:03:13 239.1.1.4 75.1.30.10 5d 17:48:41 00:03:13 239.1.1.5 75.1.30.10 5d 17:48:41 00:03:13
Field Descriptions:
Group: Multicast group address
Last reporter: Address of the last host that reported its membership for this multicast group
Uptime: Length of time since the multicast group was reported
Expires: Remaining time of the multicast group
Example of Related ProVision Software Command Output.
HP Switch# show ip igmp vlan 30
IGMP Service Protocol Info
Total VLANs with IGMP enabled : 2 Current count of multicast groups joined : 5
IGMP Filter Unknown Multicast: Disabled IGMP Filter Unknown Multicast Status: Disabled
VLAN ID : 30 VLAN Name : VLAN30 IGMP version : 2 Querier Address [this switch] : 75.1.30.1
Comware Related ProVision
display igmp group interface vlan-interface <vlan-id>
show ip igmp vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 75 Sunday, September 9, 2012 6:00 PM
2-76
Display Commandsdisplay igmp group interface vlan-interface <vlan-id>
Querier Port : Querier UpTime : 5d 18h 28m 35s Querier Expiration Time : 0h 0m 6s
Active Group Addresses Type Expires Ports Reports Queries---------------------- ---- ------- ----- -------- -------- 239.1.1.1 Filter 0h 2m 28s A2 3956 0 239.1.1.2 Filter 0h 2m 28s A2 3956 0 239.1.1.3 Filter 0h 2m 27s A2 3956 0 239.1.1.4 Filter 0h 2m 27s A2 3956 0 239.1.1.5 Filter 0h 2m 27s A2 3956 0
Operating Notes
Comware displays a list of configured vlans in the tab help. ProVision does not display dynamic help text such as this.
Comware displays an error for Invalid vlan interface. ProVision accepts the input, a validation is done later and an error is displayed.
For more information, see the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 76 Sunday, September 9, 2012 6:00 PM
2-77
Display Commandsdisplay igmp group interface vlan-interface <vlan-id> static
display igmp group interface vlan-interface <vlan-id> static
Displays information regarding statically joined IGMP multicast groups.
HP Switch# display igmp group interface Vlan-interface 400 staticStatic join group information of VPN-Instance: public net Total 21 entries Total 6 entries matched
Group Address Source Address Expires 225.1.4.6 0.0.0.0 never 239.4.4.1 0.0.0.0 never 239.4.4.2 0.0.0.0 never 239.4.4.3 0.0.0.0 never 239.4.4.4 0.0.0.0 never 239.4.5.6 0.0.0.0 never
Field Descriptions:
igmp: IGMP status and configuration information
group: Information about group members
interface: Specify interface
Vlan-interface: VLAN interface
VLAN-ID: VLAN interface
static: Static group information
Minimum Software Version: 15.09.
Comware Related ProVision
display igmp group interface vlan-interface static
No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 77 Sunday, September 9, 2012 6:00 PM
2-78
Display Commandsdisplay igmp group interface vlan-interface <vlan-id> verbose
display igmp group interface vlan-interface <vlan-id> verbose
Displays detailed information about IGMP multicast groups in a particular interface.
HP Switch# display igmp group interface Vlan-interface 400 verbose Vlan-interface400(192.168.9.2): Total 5 IGMP Groups reported Group: 225.1.5.4 Uptime: 00:07:19 Expires: 00:01:43 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.4.4.4 Uptime: 00:07:19 Expires: 00:01:38 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.9.9.9 Uptime: 00:07:19 Expires: 00:01:37 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.9.99.99 Uptime: 00:07:19 Expires: 00:01:41 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.99.99.99 Uptime: 00:07:19 Expires: 00:01:37 Last reporter: 192.168.9.9
Comware Related ProVision
display igmp group interface vlan-interface <vlan-id> verbose
No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 78 Sunday, September 9, 2012 6:00 PM
2-79
Display Commandsdisplay igmp group interface vlan-interface <vlan-id> verbose
Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 79 Sunday, September 9, 2012 6:00 PM
2-80
Display Commandsdisplay igmp group port-info
display igmp group port-info
Displays Layer 2 port information of IGMP groups, including both dynamic and static Layer 2 port entries.
Field Descriptions
Total 1 IP Group(s): Total number of IP multicast groups.
Total 1 IP Source(s): Total number of IP multicast sources.
Total 1 MAC Group(s): Total number of MAC multicast groups.
Comware Related ProVision
display igmp group port-info vlan <vid> show ip igmp vlan <vid>
HP Switch# display igmp group port-info vlan 5 Total 2 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s).
Port flags: D-Dynamic port, S-Static port, C-Copy port Subvlan flags: R-Real VLAN, C-Copy VLAN Vlan(id):5. Total 2 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s). Router port(s):total 2 port(s). F23 (D) F24 (D) IP group(s):the following ip group(s) match to one mac group. IP group address:239.4.4.4 (0.0.0.0, 239.4.4.4): Host port(s):total 1 port(s). F23 (D) MAC group(s): MAC group address: n/a Host port(s):total n/a port(s). IP group(s):the following ip group(s) match to one mac group. IP group address:239.14.14.14 (0.0.0.0, 239.14.14.14): Host port(s):total 1 port(s). F23 (D) MAC group(s): MAC group address: n/a Host port(s):total n/a port(s).
Common-CLI-Phase-3-Sept-2012.book Page 80 Sunday, September 9, 2012 6:00 PM
2-81
Display Commandsdisplay igmp group port-info
Port flags: D-Dynamic port, S-Static port, C-Copy port: Port flags: D for a dynamic port, S for a static port, and C for a port copied from a (*, G) entry to an (S, G) entry.
Subvlan flags: R-Real VLAN, C-Copy VLAN: Sub-VLAN flags: R for a real egress sub-VLAN under the current entry, and C for a sub-VLAN copied from a (*, G) entry to an (S, G) entry.
Router port(s): Number of router ports.
Router port unit board: Mask indicating a board with a router port residing on it.
(hh:mm:ss): Remaining time of the aging timer for the dynamic member port or router port:
• In standalone mode, to display the remaining life of a non-aggregation port that does not belong to the main board, you must specify the number of the slot where the corresponding card resides by using slot slot-number. This is not required for an aggregation port.
• In IRF mode, to display the remaining life of a non-aggregation port that does not belong to the main board, you must specify the member ID of the IRF member device and the slot number of the card with chassis chassis-number slot slot-number. For an aggregation port, you do not need to do this.
Operating Notes
Since ProVision switches do not need anything to be configured globally to enable igmp, no error message is displayed for a display command if igmp is not enabled. For more information on IGMP operation, see the “Multimedia Traffic Control with IP Multicast (IGMP)” chapter in the latest Advanced
Traffic Management Guide for your switch.
Common-CLI-Phase-3-Sept-2012.book Page 81 Sunday, September 9, 2012 6:00 PM
2-82
Display Commandsdisplay igmp group port-info
Example of Related ProVision Software Command Output.
display igmp group port-info Field Mappings.
Minimum Software Version: 15.09.
HP Switch(config)# show ip igmp vlan 1
IGMP Service Protocol Info
Total VLANs with IGMP enabled : 30 Current count of multicast groups joined : 20 VLAN ID : 2 VLAN Name : VLAN2 IGMP version : 2 Querier Address : 10.255.128.2 Querier Port : A1 Querier UpTime : 1h 51m 59s Querier Expiration Time : 2min 5sec Ports with multicast routers: A1, A5-A6
Active Group Addresses Type Expires Ports Reports Queries ---------------------- ---------- --------------- ---------- ------- ------- 226.0.6.7 Filter 2min 5sec A1 10 10 226.0.6.8 Standard 3min 20sec A2 20 20
Comware ProVision Software
Total 1 IP Group(s) n/a
Total 1 IP Source(s) n/a
Total 1 MAC Group(s) n/a
Port Flags n/a
Subvlan Flags n/a
Router port(s) Ports with multicast routers
(hh:mm:ss) Querier Expiration Time
IP group address Active Group Addresses
MAC group address n/a
Attribute n/a
Host port unit board n/a
Host port(s) n/a
Common-CLI-Phase-3-Sept-2012.book Page 82 Sunday, September 9, 2012 6:00 PM
2-83
Display Commandsdisplay igmp group static
display igmp group static
Displays the information regarding statically joined IGMP multicast groups.
HP Switch# display igmp group static
Static join group information
Total 19 entries
Group Address Source Address Interface Expires 225.1.1.1 0.0.0.0 Vlan1 never 225.1.1.5 0.0.0.0 Vlan1 never 225.1.4.1 0.0.0.0 Vlan4 never 225.1.5.4 0.0.0.0 Vlan5 never 225.4.4.1 0.0.0.0 Vlan4 never 225.4.4.2 0.0.0.0 Vlan4 never 225.4.4.3 0.0.0.0 Vlan4 never 225.4.4.4 0.0.0.0 Vlan4 never 225.5.5.1 0.0.0.0 Vlan5 never 225.5.5.2 0.0.0.0 Vlan5 never 225.5.5.3 0.0.0.0 Vlan5 never 225.5.5.4 0.0.0.0 Vlan5 never 225.5.5.5 0.0.0.0 Vlan5 never 225.44.46.46 0.0.0.0 Vlan1 never 225.44.46.46 0.0.0.0 Vlan4 never 225.44.46.46 0.0.0.0 Vlan5 never 225.145.145.145 0.0.0.0 Vlan1 never 225.145.145.145 0.0.0.0 Vlan4 never 225.145.145.145 0.0.0.0 Vlan5 never
Field Descriptions:
Group: Multicast group address
Expires: Remaining time of the multicast group
Example of Related ProVision Software Command Output.
HP Switch# show ip igmp vlan 1
IGMP Service Protocol InfoTotal VLANs with IGMP enabled : 30
Comware Related ProVision
display igmp group static show ip igmp vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 83 Sunday, September 9, 2012 6:00 PM
2-84
Display Commandsdisplay igmp group static
Current count of multicast groups joined : 20VLAN ID : 2VLAN Name : VLAN2IGMP version : 2Querier Address : 10.255.128.2Querier Port : A1Querier UpTime : 1h 51m 59sQuerier Expiration Time : 2min 5secPorts with multicast routers: A1, A5-A6
Active Group Addresses Type Expires Ports Reports Queries---------------------- ----- ------- ----- -------- -------226.0.6.7 Filter 2min 5sec A1 10 10226.0.6.8 Standard 3min 20sec A2 20 20
For more information, see the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 84 Sunday, September 9, 2012 6:00 PM
2-85
Display Commandsdisplay igmp group verbose
display igmp group verbose
Displays detailed information about IGMP multicast groups.HP Switch# display igmp group verboseInterface group report information Vlan-interface400(192.168.9.2): Total 5 IGMP Groups reported Group: 225.1.5.4 Uptime: 00:00:16 Expires: 00:01:54 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.4.4.4 Uptime: 00:00:16 Expires: 00:01:54 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.9.9.9 Uptime: 00:00:16 Expires: 00:01:54 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.9.99.99 Uptime: 00:00:16 Expires: 00:01:54 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.99.99.99 Uptime: 00:00:16 Expires: 00:01:54 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off
Minimum Software Version: 15.10.
Comware Related ProVision
display igmp group verbose No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 85 Sunday, September 9, 2012 6:00 PM
2-86
Display Commandsdisplay igmp group x.x.x.x static
display igmp group x.x.x.x static
Displays information regarding statically joined IGMP multicast groups.
HP Switch# display igmp group 225.44.46.46 staticStatic join group information Total 19 entries Total 3 entries matched
Group Address Source Address Interface Expires 225.44.46.46 0.0.0.0 Vlan1 never 225.44.46.46 0.0.0.0 Vlan4 never 225.44.46.46 0.0.0.0 Vlan5 never
Field Descriptions:igmp: IGMP status and configuration information
group: Information about group members
static: Static group information
Example of Related ProVision Software Command Output.
HP Switch# show ip igmp vlan 1
IGMP Service Protocol InfoTotal VLANs with IGMP enabled : 30Current count of multicast groups joined : 20VLAN ID : 2VLAN Name : VLAN2IGMP version : 2Querier Address : 10.255.128.2Querier Port : A1Querier UpTime : 1h 51m 59sQuerier Expiration Time : 2min 5secPorts with multicast routers: A1, A5-A6
Active Group Addresses Type Expires Ports Reports Queries---------------------- ----- ------- ----- -------- -------226.0.6.7 Filter 2min 5sec A1 10 10226.0.6.8 Standard 3min 20sec A2 20 20
For more information, see the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display igmp group x.x.x.x static show ip igmp vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 86 Sunday, September 9, 2012 6:00 PM
2-87
Display Commandsdisplay igmp group x.x.x.x verbose
display igmp group x.x.x.x verbose
Displays detailed information about a specified IGMP multicast group.
HP Switch# display igmp group 239.4.4.4 verboseInterface group report information Vlan-interface400(192.168.9.2): Total 5 IGMP Groups reported Group: 239.4.4.4 Uptime: 00:01:56 Expires: 00:02:06 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off
Minimum Software Version: 15.10.
Comware Related ProVision
display igmp group x.x.x.x verbose No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 87 Sunday, September 9, 2012 6:00 PM
2-88
Display Commandsdisplay igmp interface
display igmp interface
Displays IGMP configuration and operation information of the specified inter-face or all IGMP-enabled interfaces.
HP Switch# display igmp interface Interface informationVlan-interface30(75.1.30.1):IGMP is enabled Current IGMP version is 2 Value of query interval for IGMP(in seconds): 125 Value of other querier present interval for IGMP(in seconds): 255 Value of maximum query response time for IGMP(in seconds): 10 Querier for IGMP: 75.1.30.1 (this router) Total 5 IGMP Groups reported
Field Descriptions:
Vlan-interface200 (10.10.1.20): Interface and IP address
Current IGMP version: Version of IGMP currently running on the interface
Value of query interval for IGMP(in seconds): IGMP general query interval, in seconds
Value of other querier present interval for IGMP(in seconds): Other querier present interval, in seconds
Value of maximum query response time for IGMP(in seconds): Maximum response time for IGMP general queries, in seconds
Value of last member query interval(in seconds): IGMP last member query inter-val, in seconds
Value of startup query interval(in seconds): IGMP startup query interval, in seconds
Value of startup query count: Number of IGMP general queries the device sends on startup
Comware Related ProVision
display igmp interface show ip igmp vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 88 Sunday, September 9, 2012 6:00 PM
2-89
Display Commandsdisplay igmp interface
General query timer expiry: Remaining time of the IGMP general query timer, where “off” means that the timer never expires
Querier for IGMP: IP address of the IGMP querier
IGMP activity: Statistics of IGMP activities (joins and leaves)
Multicast routing on this interface: Whether the multicast routing and forward-ing function is enabled
Robustness: Robustness variable of the IGMP querier
Require-router-alert: Dropping IGMP messages without Router-Alert (enabled/disabled)
Fast-leave: Fast leave processing status (enabled/disabled)
Ssm-mapping: IGMP SSM mapping status (enabled/disabled)
Startup-query-timer-expiry: Remaining time of the startup query timer, where “off” means that the timer never expires
Other-querier-present-timer-expiry: Remaining time of the other querier present timer, where “off” means that the timer never expires
Proxying interface: IGMP proxy interface, where “none” means that no proxy interface exists
Total 1 IGMP Group reported: Total number of IGMP groups the interface has dynamically joined
IGMP proxy is enabled: IGMP proxying is enabled
Version1-querier-present-timer-expiry: Remaining time of the IGMPv1 querier present timer, where “off” means that the timer never expires
Version2-querier-present-timer-expiry: Remaining time of the IGMPv2 querier present timer, where “off” means that the timer never expires
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command.
HP Switch# show ip igmp vlan 30
IGMP Service Protocol Info
Total VLANs with IGMP enabled : 2
Current count of multicast groups joined : 5
Common-CLI-Phase-3-Sept-2012.book Page 89 Sunday, September 9, 2012 6:00 PM
2-90
Display Commandsdisplay igmp interface
IGMP Filter Unknown Multicast: Disabled
IGMP Filter Unknown Multicast Status: Disabled
VLAN ID : 30
VLAN Name : VLAN30
IGMP version : 2
Querier Address [this switch] : 75.1.30.1
Querier Port :
Querier UpTime : 5d 18h 39m 7s
Querier Expiration Time : 0h 0m 4s
Active Group Addresses Type Expires Ports Reports Queries ---------------------- ---- ------- ------- ------ ------- 239.1.1.1 Filter 0h 2m 25s A2 3961 0 239.1.1.2 Filter 0h 2m 25s A2 3961 0 239.1.1.3 Filter 0h 2m 25s A2 3961 0 239.1.1.4 Filter 0h 2m 25s A2 3961 0 239.1.1.5 Filter 0h 2m 24s A2 3961 0
Operating Notes
ProVision does not support VPN instance.
For more information, see the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 90 Sunday, September 9, 2012 6:00 PM
2-91
Display Commandsdisplay igmp interface verbose
display igmp interface verbose
Displays detailed IGMP configuration and operation information.
HP Switch# display igmp interface verboseInterface information Vlan-interface1(10.100.239.141): IGMP is enabled Current IGMP version is 2 Value of query interval for IGMP(in seconds): 125 Value of other querier present interval for IGMP(in seconds): 255 Value of maximum query response time for IGMP(in seconds): 10 Value of last member query interval(in seconds): 10 Value of startup query interval(in seconds): 31 Value of startup query count: 2 General query timer expiry (hours:minutes:seconds): 00:01:58 Querier for IGMP: 10.100.239.141 (this router) IGMP activity: 378 joins, 0 leaves Multicast routing on this interface: disabled Robustness: 2 Require-router-alert: enabled Fast-leave: enabled Ssm-mapping: n/a Startup-query-timer-expiry: off Other-querier-present-timer-expiry: off Proxying interface: n/a Total 9 IGMP Groups reported
Vlan-interface2(192.168.9.2): IGMP is enabled Current IGMP version is 2 Value of query interval for IGMP(in seconds): 125 Value of other querier present interval for IGMP(in seconds): 255 Value of maximum query response time for IGMP(in seconds): 10 Value of last member query interval(in seconds): 10 Value of startup query interval(in seconds): 31 Value of startup query count: 2 General query timer expiry (hours:minutes:seconds): 00:01:56 Querier for IGMP: 192.168.9.2 (this router) IGMP activity: 0 joins, 0 leaves Multicast routing on this interface: disabled Robustness: 2
Comware Related ProVision
display igmp interface verbose No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 91 Sunday, September 9, 2012 6:00 PM
2-92
Display Commandsdisplay igmp interface verbose
Require-router-alert: enabled Fast-leave: disabled Ssm-mapping: n/a Startup-query-timer-expiry: off Other-querier-present-timer-expiry: off Proxying interface: n/a
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 92 Sunday, September 9, 2012 6:00 PM
2-93
Display Commandsdisplay igmp interface vlan-interface <vlan-id>
display igmp interface vlan-interface <vlan-id>
Displays the IGMP configuration and operation information of the specified interface or all IGMP-enabled interfaces.
Field Descriptions
Vlan-interface: Interface and IP address.
Current IGMP Version: Version of IGMP currently running on the interface.
Value of query interval for IGMP(in seconds): IGMP general query interval, in seconds.
Value of other querier present interval for IGMP (in seconds): Other querier present interval, in seconds.
Value of maximum query response time for IGMP(in seconds): Maximum response time for IGMP general queries, in seconds.
Querier for IGMP: IP address of the IGMP querier.
Operating Notes
If the VLAN interface is invalid, the switch displays “VLAN <VLAN-ID> not found”.
Comware Related ProVision
display igmp interface vlan-interface <vlan-id>
show ip igmp vlan <vid>
HP Switch# display igmp interface vlan-interface 1
Vlan-interface1(10.100.1.238): IGMP is enabled Current IGMP version is 2 Value of query interval for IGMP(in seconds): 125 Value of other querier present interval for IGMP(in seconds): 255 Value of maximum query response time for IGMP(in seconds): 10 Querier for IGMP: 10.100.1.238 (this router) Total 8 IGMP Groups reported
Common-CLI-Phase-3-Sept-2012.book Page 93 Sunday, September 9, 2012 6:00 PM
2-94
Display Commandsdisplay igmp interface vlan-interface <vlan-id>
For more information on switch IGMP operation, see the “Multimedia Traffic Control with IP Multicast (IGMP)” chapter in the latest Advanced Traffic
Management Guide for your switch.
Example of Related ProVision Software Command Output.
display igmp interface vlan-interface <vlan-id> Field Mappings.
HP Switch(config)# show ip igmp vlan 1
IGMP Service Protocol Info
Total VLANs with IGMP enabled : 30 Current count of multicast groups joined : 20 VLAN ID : 2 VLAN Name : VLAN2 IGMP version : 2 Querier Address : 10.255.128.2 Querier Port : A1 Querier UpTime : 1h 51m 59s Querier Expiration Time : 2min 5sec Ports with multicast routers: A1, A5-A6
Active Group Addresses Type Expires Ports Reports Queries ---------------------- ---------- --------------- ---------- ------- ------- 226.0.6.7 Filter 2min 5sec A1 10 10 226.0.6.8 Standard 3min 20sec A2 20 20
Comware ProVision Software
Vlan-interface VLAN-ID
Current IGMP Version IGMP version
Value of query interval n/a
Value of other querier n/a
Value of maximum query response time
n/a
Querier for IGMP Querier Address
n/a VLAN Name
n/a Querier Port
n/a Querier UpTime
Common-CLI-Phase-3-Sept-2012.book Page 94 Sunday, September 9, 2012 6:00 PM
2-95
Display Commandsdisplay igmp interface vlan-interface <vlan-id>
Minimum Software Version: 15.09.
Startup-query-timer-expiry Querier Expiration Time
n/a Ports with multicast routers
n/a Active Group Addresses
n/a Type
Startup-query-timer-expiry Expires
n/a Ports
n/a Reports
IGMP activity Queries
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 95 Sunday, September 9, 2012 6:00 PM
2-96
Display Commandsdisplay igmp routing-table
display igmp routing-table
Displays information regarding the IGMP routing table.
HP Switch# display igmp routing-table
Routing tableTotal 5 entries
00001. (*, 239.1.1.1) List of 1 downstream interface Vlan-interface30 (75.1.30.1), Protocol: IGMP
00002. (*, 239.1.1.2) List of 1 downstream interface Vlan-interface30 (75.1.30.1), Protocol: IGMP
00003. (*, 239.1.1.3) List of 1 downstream interface Vlan-interface30 (75.1.30.1), Protocol: IGMP
00004. (*, 239.1.1.4) List of 1 downstream interface Vlan-interface30 (75.1.30.1), Protocol: IGMP
00005. (*, 239.1.1.5) List of 1 downstream interface Vlan-interface30 (75.1.30.1), Protocol: IGMP
Field Descriptions:
Routing table of VPN-Instance: public net: Public network IGMP routing table
00001: Sequence number of this (*, G) entry
(*, 225.1.1.1): A (*, G) entry of the IGMP routing table
Flag: IGMP route flags:
Comware Related ProVision
display igmp routing-table show ip igmp vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 96 Sunday, September 9, 2012 6:00 PM
2-97
Display Commandsdisplay igmp routing-table
• ACT: Indicates IGMP routing entries that have been used for forward-ing data packets but have the multicast group address out of the SSM group range
• SUC: Indicates IGMP routing entries that have been added to the forwarding table and have the multicast group address within the SSM group range
List of 1 downstream interface: Downstream interface list, namely, the interfaces to which multicast data for this group will be forwarded
in include mode: The downstream interface is in the include mode
in exclude mode: The downstream interface is in the exclude mode
Downstream interface is none: No downstream interfaces exist
Protocol: Protocol type
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see “show ip igmp vlan <vid>” on page 2-89.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 97 Sunday, September 9, 2012 6:00 PM
2-98
Display Commandsdisplay interface
display interface
Displays current state about a specified port and related information. If no port number is specified, information is displayed for all ports.
HP Switch# display interface a1 A1 current state: UP IP Packet Frame Type: n/a, Hardware Address: 001560-f9b0ff Description: A1 interface Loopback is n/a Media type is twisted Pair Port hardware type is 100/1000T 1000Mbps-speed mode, full-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled The Maximum Frame Length is 9216 Broadcast MAX-ratio: n/a Unicast MAX-ratio: n/a Multicast MAX-ratio: n/a Jumbo frame: [ see "show jumbos"] PVID : 1 Mdi type: MDIX Link delay is n/a Port link-type: n/a Tagged VLAN ID : none Untagged VLAN ID : 1 Port priority: No-override Last clearing of counters: n/a Peak value of input: n/a Peak value of output: n/a Last 300 seconds input: 0 packets/sec 128846 bytes/sec 0% Last 300 seconds output: 0 packets/sec 65444 bytes/sec 0% Input (total): 0 packets, 26 bytes 3 unicasts, 2 broadcasts, 21 multicasts, 0 pauses Input (normal): 0 packets, 26 bytes 3 unicasts, 2 broadcasts, 21 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, n/a throttles 0 CRC, 0 frame, n/a overruns, n/a aborts n/a ignored, n/a parity errors Output (total): 0 packets, 24 bytes 0 unicasts, 4 broadcasts, 20 multicasts, 0 pauses Output (normal): 0 packets, 24 bytes
Comware Related ProVision
display interface show interface <port>
Common-CLI-Phase-3-Sept-2012.book Page 98 Sunday, September 9, 2012 6:00 PM
2-99
Display Commandsdisplay interface
0 unicasts, 4 broadcasts, 20 multicasts, 0 pauses Output: 0 output errors, n/a underruns, n/a buffer failures n/a aborts, 0 deferred, 0 collisions, 0 late collisions n/a lost carrier, n/a no carrier
Example of Related ProVision Software Command Output.
HP Switch# show interfaces briefStatus and Counters - Port Status
| Intrusion MDI Flow BcastPort Type | Alert Enabled Status Mode Mode Ctrl Limit----- ---------+ --------- ------- ------ ---- ---- ---- -----B1 100/1000T | No Yes Down Auto-10-100 Auto off 0B2 100/1000T | No Yes Down 1000FDx Auto off 0B3 100/1000T | No Yes Down 1000FDx Auto off 0B4 100/1000T | No Yes Down 1000FDx Auto off 0B5 100/1000T | No Yes Down 1000FDx Auto off 0B6 100/1000T | No Yes Down 1000FDx Auto off 0
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 99 Sunday, September 9, 2012 6:00 PM
2-100
Display Commandsdisplay interface brief
display interface brief
Displays brief information about Layer 3 interfaces (tunnels) and Layer 2 interfaces.
Field Descriptions
The brief information of interface(s) under route mode: Brief information about Layer 3 interfaces.
The brief information of interface(s) under bridge mode: Brief information about Layer 2 interfaces.
Link: ADM - administratively down; Stby - standby: Link status:• ADM—The interface has been administratively shut down. To recover
its physical layer state, perform the undo shutdown command.
• Stby—The interface is operating as a backup interface.
Comware Related ProVision
display interface brief show interfaces brief
HP Switch(config)# display interface briefThe brief information of interface(s) under route mode:Link: ADM - administratively down; Stby - standbyProtocol: (s) - spoofing Interface Link Protocol Main IP Description tunnel-1 Down UP 20.1.1.1 tunnel1
The brief information of interface(s) under bridge mode:Link: ADM - administratively down; Stby - standbySpeed or Duplex: (a)/A - auto; H - half; F - fullType: A - access; T - trunk; H - hybridInterface Link Speed Duplex Type PVID DescriptionA1 UP auto A n/a 1 port1A2 DOWN auto A n/a 20 port2A3 DOWN auto A n/a 1A4 DOWN auto A n/a 1A5 DOWN auto A n/a 1A6 DOWN auto A n/a 1A7 DOWN auto A n/a 1A8 DOWN auto A n/a 1A9 DOWN auto A n/a 1. ..
Common-CLI-Phase-3-Sept-2012.book Page 100 Sunday, September 9, 2012 6:00 PM
2-101
Display Commandsdisplay interface brief
Speed or Duplex: (a)/A - auto; H - half; F - full: If the speed of an interface is automatically negotiated, its speed attribute includes the auto negotiation flag, letter a in parentheses. If the duplex mode of an interface is automatically negotiated, its duplex mode attribute includes the auto negotiation flag, letter a in parentheses or a capital A. Letter H indicates the half duplex mode, and letter F indicates the full duplex mode.
Type: A - access; T - trunk; H - hybrid: Link type options for Ethernet interfaces.
Protocol: (s) - spoofing: If the network layer protocol state of an interface is shown as UP, but its link is an on-demand link or not present, its protocol attribute includes the spoofing flag (an s in parentheses).
Interface: The abbreviated interface name.
Link: The physical link state of the interface.
Speed: The interface speed, in bps.
PVID: The default VLAN ID.
Description: Name of the interface.
Operating Notes
For more information on interface statistics, see the “Port Status and Config-uration” chapter in the latest Management and Configuration Guide for your switch.
Common-CLI-Phase-3-Sept-2012.book Page 101 Sunday, September 9, 2012 6:00 PM
2-102
Display Commandsdisplay interface brief
Example of Related ProVision Software Command Output.
display interface brief Field Mappings.
Minimum Software Version: 15.09.
HP Switch(config)# show interfaces brief
Status and Counters - Port Status
| Intrusion MDI Flow Bcast Port Type | Alert Enabled Status Mode Mode Ctrl Limit ------ --------- + --------- ------- ------ ---------- ---- ---- ----- A1 10GbE-T | No Yes Up 1000FDx MDIX off 0 A2 10GbE-T | No Yes Down 10GigFD MDI off 0 A3 10GbE-T | No Yes Down 10GigFD MDIX off 0 A4 10GbE-T | No Yes Down 10GigFD Auto off 0 A5 10GbE-T | No Yes Down 10GigFD Auto off 0 A6 10GbE-T | No Yes Down 10GigFD Auto off 0 A7 10GbE-T | No Yes Down 10GigFD Auto off 0 A8 10GbE-T | No Yes Down 10GigFD Auto off 0
Comware ProVision Software
interfaces under route mode n/a
interfaces under bridge mode n/a
Link status Status
Speed or Duplex Mode/MDI Mode
Type n/a
Protocol n/a
Interface Port
Link Status
Speed Type
PVID n/a
Description n/a
n/a Intrusion Alert
n/a Bcast Limit
Common-CLI-Phase-3-Sept-2012.book Page 102 Sunday, September 9, 2012 6:00 PM
2-103
Display Commandsdisplay interface brief down
display interface brief down
Displays information about interfaces in down state and the relevant causes.
Field Descriptions
The brief information of interface(s) under route mode: Brief information about Layer 3 interfaces.
The brief information of interface(s) under bridge mode: Brief information about Layer 2 interfaces.
Link: ADM - administratively down; Stby - standby: Link status:• ADM—The interface has been administratively shut down. To recover
its physical layer state, perform the undo shutdown command.
• Stby—The interface is operating as a backup interface.
Interface: Interface number.
Link Cause: Displays information about interfaces in the down state and the causes.
Comware Related ProVision
display interface brief down show interfaces brief
HP Switch(config)# display interface brief downThe brief information of interface(s) under route mode:Link: ADM - administratively down; Stby - standbyInterface Link Cause tunnel-1 Down n/a
The brief information of interface(s) under bridge mode:Link: ADM - administratively down; Stby - standbyInterface Link Cause A2 Down Not connected A3 Down Not connected A4 Down Not connected A5 Down Not connected A6 Down Not connected A7 Down Not connected . . .
Common-CLI-Phase-3-Sept-2012.book Page 103 Sunday, September 9, 2012 6:00 PM
2-104
Display Commandsdisplay interface brief down
Operating Notes
For the interfaces under route mode, only “interface tunnels” are displayed; other types are not supported.
H3C displays one of the reasons for the field “Cause” if the port is down: Not connected, Administratively, Link-Aggregation interface down, OAM connec-tion failure, DLDP connection failure, Loopback detection-protected, BPDU-protected, Monitor-Link uplink down.
ProVision doesn’t support OAM and DLDP.
For more information, see the “Port Status and Configuration” chapter in the latest Management and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
display interface brief down Field Mappings.
Minimum Software Version: 15.09.
HP Switch(config)# show interfaces brief
Status and Counters - Port Status
| Intrusion MDI Flow Bcast Port Type | Alert Enabled Status Mode Mode Ctrl Limit ------ --------- + --------- ------- ------ ---------- ---- ---- ----- A1 10GbE-T | No Yes Up 1000FDx MDIX off 0 A2 10GbE-T | No Yes Down 10GigFD MDI off 0 A3 10GbE-T | No Yes Down 10GigFD MDIX off 0 A4 10GbE-T | No Yes Down 10GigFD Auto off 0 A5 10GbE-T | No Yes Down 10GigFD Auto off 0 A6 10GbE-T | No Yes Down 10GigFD Auto off 0 A7 10GbE-T | No Yes Down 10GigFD Auto off 0 A8 10GbE-T | No Yes Down 10GigFD Auto off 0
Comware ProVision Software
interfaces under route mode n/a
interfaces under bridge mode n/a
Interface Port
Link Cause Status
Common-CLI-Phase-3-Sept-2012.book Page 104 Sunday, September 9, 2012 6:00 PM
2-105
Display Commandsdisplay ip as-path
display ip as-path
Displays BGP AS-Path list information
HP Switch# display ip as-path ListID Mode Expression test1 permit $25
Field Descriptions
ListID: AS path list ID.
Mode: Match mode — permit or deny.
Expression: Regular expression for matching.
Operating Notes
To enable BGP operation in ProVision software, see the “BGP (Border Gate-way Protocol)” chapter in the latest Multicast and Routing Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch# show ip aspath-list
Route Policy AS-path List test1: 1 entries seq 5 permit "$25" ip as-path Field Mappings
Minimum Software Version: 15.08.
Comware Related ProVision
display ip as-path show ip aspath-list
Comware ProVision Software
ListID as-path name
Mode permit or deny
Expression $ expression
Common-CLI-Phase-3-Sept-2012.book Page 105 Sunday, September 9, 2012 6:00 PM
2-106
Display Commandsdisplay ip check source
display ip check source
Displays display dynamic IP source guard binding entries.
Field Descriptions
Total entries found: Total number of found entries
MAC Address: MAC address of the dynamic IP source guard binding entry. N/A means that no MAC address is bound in the entry.
IP Address: IP address of the dynamic IP source guard binding entry. N/A means that no IP address is bound in the entry.
VLAN: VLAN bound to the IP source guard binding entry. N/A means that no VLAN is bound in the entry.
Interface: Interface of the dynamic IP source guard binding entry.
Type: Type of the dynamic IP source guard binding entry, including:
• DHCP-SNP—DHCP snooping entry.
• DHCP-RLY—DHCP relay entry.
• DHCPv6-SNP—DHCPv6 snooping entry.
• ND-SNP—ND snooping entry.
Operating Notes
For more information about DHCP snooping, see the “Configuring Advanced Threat Protection” chapter in the latest Access Security Guide for your switch.
Comware Related ProVision
display ip check source show dhcp-snooping bindings
HP Switch# display ip check source
Total entries found: 3 MAC Address IP Address VLAN Interface Status 005056-9f2c8b 192.168.1.1 1 n/a Dynamic 005056-9f2c9b 192.167.1.1 1 n/a Dynamic 005056-9f2c9b 192.167.0.1 2 n/a Dynamic
Common-CLI-Phase-3-Sept-2012.book Page 106 Sunday, September 9, 2012 6:00 PM
2-107
Display Commandsdisplay ip check source
Example of Related ProVision Software Command Output.
display ip check source Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
Total entries found n/a
MAC Address n/a
IP Address n/a
VLAN n/a
Interface n/a
Type n/a
HP Switch(config)# show dhcp-snooping
DHCP Snooping Information
DHCP Snooping : Yes
Enabled Vlans :
Verify MAC : Yes
Option 82 untrusted policy : drop
Option 82 Insertion : Yes
Option 82 remote-id : mac
Store lease database : Not configured
Port Trust
----- -----
B1 No
B2 No
Common-CLI-Phase-3-Sept-2012.book Page 107 Sunday, September 9, 2012 6:00 PM
2-108
Display Commandsdisplay ip community-list
display ip community-list
Displays BGP community list information HP Switch# display ip community-list Community List Number community-1 permit 10
deny 50
Field Descriptions
Community List Number < community-name >: Specifies the community being reported.
permit: Permitted routes that belong to the community .
deny: Denied routes that belong to the community.
Operating Notes
To enable BGP in ProVision software, see the “BGP (Border Gateway Proto-col)” chapter in the latest Multicast and Routing Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch# show ip community-list
ip community list community-1 standard permit 10 deny 50
ip as-path Field Mappings.
Minimum Software Version: 15.08.
Comware Related ProVision
display ip community-list show ip community-list
Comware ProVision Software
Community List Number ip community list
permit permit
deny deny
Common-CLI-Phase-3-Sept-2012.book Page 108 Sunday, September 9, 2012 6:00 PM
2-109
Display Commandsdisplay ip http
display ip http
Displays information about HTTP.
HP Switch# display ip httpHTTP port: 80Basic ACL: n/aCurrent connection: 0Operation status: enabled
Minimum Software Version: 15.10.
Comware Related ProVision
display ip http No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 109 Sunday, September 9, 2012 6:00 PM
2-110
Display Commandsdisplay ip https
display ip https
Displays information about HTTPs.
HP Switch# display ip httpsHTTPS port: 443SSL server policy: n/aCertificate access-control-policy: n/aBasic ACL: n/aOperation status: disabled
Minimum Software Version: 15.10.
Comware Related ProVision
display ip https No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 110 Sunday, September 9, 2012 6:00 PM
2-111
Display Commandsdisplay ip ip-prefix
display ip ip-prefix
Displays all the prefix list information, including list name, address, length, rule type, ge and le [greater than or equal /less than or equal w.r.t mask range] for a specific network. This command is available only in manager mode.
HP Switch# display ip ip-prefix abc Prefix-list abc Permitted n/a Denied n/a index: 5 permit 11.2.3.4/8 ge 8 le 8
Example of Related ProVision Software Command Output.
HP Switch# show ip prefix-list
ip prefix-list Odd: 4 entriesseq 5 permit 10.1.1.1/24 ge 24 le 24seq 10 deny 10.1.2.1/24 ge 24 le 24seq 15 permit 10.1.3.1/24 ge 24 le 24seq 20 deny 10.1.4.1/24 ge 24 le 24
ip prefix-list Even: 4 entriesseq 5 deny 10.1.1.1/24 ge 24 le 24seq 10 permit 10.1.2.1/24 ge 24 le 24seq 15 deny 10.1.3.1/24 ge 24 le 24seq 20 permit 10.1.4.1/24 ge 24 le 24
Operating Notes
For more information, refer to the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display ip ip-prefix show ip prefix-list
Common-CLI-Phase-3-Sept-2012.book Page 111 Sunday, September 9, 2012 6:00 PM
2-112
Display Commandsdisplay ipv6 dhcp duid
display ipv6 dhcp duid
Displays the DUID of the local switch.
Field Descriptions
The DUID of this device: The DHCP for IPv6 Unique Identifier (DUID).
Operating Notes
For more information about IPv6 DHCPv6, see the “DHCPv6-Relay” chapter in the latest IPv6 Configuration Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display ipv6 dhcp duid No equivalent ProVision software command
HP Switch# display ipv6 dhcp duid
The DUID of this device: 0003-0001-00e0-fc00-5552.
Common-CLI-Phase-3-Sept-2012.book Page 112 Sunday, September 9, 2012 6:00 PM
2-113
Display Commandsdisplay ipv6 dhcp relay server-address all
display ipv6 dhcp relay server-address all
Displays all DHCPv6 server address information.
Field Descriptions
Interface: Interface that serves as the DHCPv6 relay agent.
Server address(es): DHCPv6 server address(es) specified on the interface.
Output Interface: Outgoing interface of DHCPv6 packets.
Operating Notes
For more information about IPv6 DHCPv6, see the “DHCPv6-Relay” chapter in the latest IPv6 Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
Comware Related ProVision
display ipv6 dhcp relay server-address all show ipv6 helper-address
HP Switch# display ipv6 dhcp relay server-address allInterface: Vlan2Server address(es) Output Interface1::1FF02::1:2 Vlan4 Interface: Vlan3Server address(es) Output Interface1::1FF02::1:2 Vlan4
HP Switch(config)# show ipv6 helper-address
VLAN: 14
IPv6 Helper Address Egress Vlan
---------------------------------------------- -----------
FF05::1:3 14
Common-CLI-Phase-3-Sept-2012.book Page 113 Sunday, September 9, 2012 6:00 PM
2-114
Display Commandsdisplay ipv6 dhcp relay server-address all
display ipv6 dhcp relay server-address all Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
Interface VLAN
Server address(es) IPv6 Helper Address
Output Interface Egress Vlan
Common-CLI-Phase-3-Sept-2012.book Page 114 Sunday, September 9, 2012 6:00 PM
2-115
Display Commandsdisplay ipv6 dhcp relay server-address interface <id>
display ipv6 dhcp relay server-address interface <id>
Displays DHCPv6 server address information of the specified interface.
Field Descriptions
Interface: Interface that serves as the DHCPv6 relay agent.
Server address(es): DHCPv6 server address(es) specified on the interface.
Output Interface: Outgoing interface of DHCPv6 packets.
Operating Notes
For more information about IPv6 DHCPv6, see the “DHCPv6-Relay” chapter in the latest IPv6 Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
Comware Related ProVision
display ipv6 dhcp relay server-address interface <id>
show ipv6 helper-address
HP Switch# display ipv6 dhcp relay server-address interface vlan-interface 2Interface: Vlan2Server address(es) Output Interface1::1FF02::1:2 Vlan4
HP Switch(config)# show ipv6 helper-address
VLAN: 14
IPv6 Helper Address Egress Vlan
---------------------------------------------- -----------
FF05::1:3 14
Common-CLI-Phase-3-Sept-2012.book Page 115 Sunday, September 9, 2012 6:00 PM
2-116
Display Commandsdisplay ipv6 dhcp relay server-address interface <id>
display ipv6 dhcp relay server-address interface <id> Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
Interface VLAN
Server address(es) IPv6 Helper Address
Output Interface Egress Vlan
Common-CLI-Phase-3-Sept-2012.book Page 116 Sunday, September 9, 2012 6:00 PM
2-117
Display Commandsdisplay ipv6 dhcp relay statistics
display ipv6 dhcp relay statistics
Displays packet statistics on the DHCPv6 relay agent.
Field Descriptions
Packets dropped: Number of discarded packets.
Error: Number of discarded error packets.
Excess of rate limit: Number of packets discarded due to excess of rate limit.
Packets received: Number of received packets.
SOLICIT: Number of received solicit packets.
REQUEST: Number of received request packets.
CONFIRM: Number of received confirm packets.
RENEW: Number of received renew packets.
Comware Related ProVision
displayipv6 dhcp relay statistics show dhcpv6-relay
HP Switch# display ipv6 dhcp relay statisticsPackets dropped : 4 Error : 4 Excess of rate limit : n/aPackets received : 14 SOLICIT : 0 REQUEST : 0 CONFIRM : 0 RENEW : 0 REBIND : 0 RELEASE : 0 DECLINE : 0 INFORMATION-REQUEST : 7 RELAY-FORWARD : 0 RELAY-REPLY : 7Packets sent : 14 ADVERTISE : 0 RECONFIGURE : 0 REPLY : 7 RELAY-FORWARD : 7 RELAY-REPLY : 0
Common-CLI-Phase-3-Sept-2012.book Page 117 Sunday, September 9, 2012 6:00 PM
2-118
Display Commandsdisplay ipv6 dhcp relay statistics
REBIND: Number of received rebind packets.
RELEASE: Number of received release packets.
DECLINE: Number of received decline packets.
INFORMATION-REQUEST: Number of received information request packets.
RELAY-FORWARD: Number of received relay-forward packets.
RELAY-REPLY: Number of received relay-reply packets.
Packets sent: Number of sent packets.
ADVERTISE: Number of sent advertise packets.
RECONFIGURE: Number of sent reconfigure packets.
REPLY: Number of sent reply packets.
RELAY-FORWARD: Number of sent Relay-forward packets.
RELAY-REPLY: Number of sent Relay-reply packets.
Operating Notes
For more information about IPv6 DHCPv6, see the “DHCPv6-Relay” chapter in the latest IPv6 Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show dhcpv6-relay
DHCPV6 Relay Agent : Enabled
Client Requests Server Responses
VLAN Name Received Dropped Failed Received Dropped Failed ---------- ---------- ---------- ---------- ---------- ---------- ---------- DEFAULT... 120 0 0 120 0 0 VLAN20 30 1 0 29 2 1
Common-CLI-Phase-3-Sept-2012.book Page 118 Sunday, September 9, 2012 6:00 PM
2-119
Display Commandsdisplay ipv6 dhcp relay statistics
display ipv6 dhcp relay statistics Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
Packets dropped Dropped
Error Failed
Excess of rate limit n/a
Packets received Received
Common-CLI-Phase-3-Sept-2012.book Page 119 Sunday, September 9, 2012 6:00 PM
2-120
Display Commandsdisplay ipv6 routing-table
display ipv6 routing-table
Displays brief ipv6 routing information. The verbose option displays detailed information about the ipv6 routing table.
HP Switch# display ipv6 routing-table Routing Table: Public Destinations: 3 Routes : 3
Destination: ::1/128 Protocol : DirectNextHop : ::1 Preference: 0Interface : InLoop0 Cost : 0
Destination: 6::/64 Protocol : OSPFv3NextHop : FE80::3A22:D6FF:FEB4:4450 Preference: 10Interface : Vlan2 Cost : 2
Destination: 7::/64 Protocol : DirectNextHop : 7::2 Preference: 0Interface : Vlan2 Cost : 0
HP Switch# display ipv6 routing-table verboseRouting Table : Public Destinations : 2 Routes : 2
Destination : ::1 PrefixLength : 128NextHop : ::1 Preference : 0RelayNextHop : n/a Tag : n/aNeighbor : n/a ProcessID : n/aInterface : InLoopBack0 Protocol : DirectState : Active NoAdv Cost : 0Tunnel ID : n/a Label : n/aAge : 28864sec
Destination : 6:: PrefixLength : 64NextHop : FE80::3A22:D6FF:FEB4:4450 Preference : 10RelayNextHop : n/a Tag : n/aNeighbor : n/a ProcessID : n/aInterface : Vlan-interface2 Protocol : OSPFv3State : Active Adv Cost : 2Tunnel ID : n/a Label : n/aAge : 21665sec
Comware Related ProVision
display ipv6 routing-table show ipv6 route
Common-CLI-Phase-3-Sept-2012.book Page 120 Sunday, September 9, 2012 6:00 PM
2-121
Display Commandsdisplay ipv6 routing-table
Example of Related ProVision Software Command Output.
HP Switch# show ipv6 route
IPv6 Route Entries
Destination : ::/0Gateway : 2001:db8:e::55:2Type : static Sub-Type : NA Distance : 130 1 Metric : 1
Destination : ::1/128Gateway : lo0Type : connected Sub-Type : NA Distance : 0 Metric : 1
Destination : 2001:db8:1::127/128Gateway : lo6Type : connected Sub-Type : NA Distance : 0 Metric : 1
Destination : 2001:db8:a::/64Gateway : fe80::22:1%vlan22Type : ospf3 Sub-Type : InterArea Distance : 110 Metric : 2
Destination : 2001:db8:b::/64Gateway : VLAN22Type : connected Sub-Type : NA Distance : 0 Metric : 1
Destination : 2001:db8:c::/64Gateway : 2001:db8:e::55:2Type : static Sub-Type : NA Distance : 120 Metric : 1
-- MORE --, next page: Space, next line: Enter, quit: Control-C
Operating Notes
For more information, refer to the latest IPv6 Configuration Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 121 Sunday, September 9, 2012 6:00 PM
2-122
Display Commandsdisplay ipv6 routing-table ipv6-address
display ipv6 routing-table ipv6-address
Displays routing information for a specified destination ipv6 address. The verbose option displays detailed information for the specified destination ipv6 address.
HP Switch# display ipv6 routing-table 6::1 64Routing Table : n/aSummary Count : n/a
Destination : 6::/64 Protocol : DirectNextHop : 6::1 Preference : 0Interface : Vlan2 Cost : 1HP Switch# display ipv6 routing-table 6::1 64 verboseRouting Table : n/aSummary Count : n/a Destination : 6:: PrefixLength : 64 NextHop : 6::1 Preference : 0 RelayNextHop : n/a Tag : n/a Neighbor : n/a Process ID : n/a Interface : Vlan-interface2 Protocol : Direct State : n/a Cost : 1 Tunnel ID : n/a Label : n/a Age : n/a
Example of Related ProVision Software Command Output.
HP Switch# show ipv6 route
IPv6 Route Entries
Destination : ::/0Gateway : 2001:db8:e::55:2Type : static Sub-Type : NA Distance : 130 1 Metric : 1
Destination : ::1/128Gateway : lo0Type : connected Sub-Type : NA Distance : 0 Metric : 1
Destination : 2001:db8:1::127/128Gateway : lo6Type : connected Sub-Type : NA Distance : 0 Metric : 1
Destination : 2001:db8:a::/64Gateway : fe80::22:1%vlan22
Comware Related ProVision
display ipv6 routing-table ipv6-address show ipv6 route
Common-CLI-Phase-3-Sept-2012.book Page 122 Sunday, September 9, 2012 6:00 PM
2-123
Display Commandsdisplay ipv6 routing-table ipv6-address
Type : ospf3 Sub-Type : InterArea 2 Distance : 110 Metric : 2
Destination : 2001:db8:b::/64Gateway : VLAN22Type : connected Sub-Type : NA Distance : 0 3 Metric : 1
Destination : 2001:db8:c::/64Gateway : 2001:db8:e::55:2Type : static Sub-Type : NA Distance : 120 Metric : 1
-- MORE --, next page: Space, next line: Enter, quit: Control-C
Operating Notes
For more information, refer to the latest IPv6 Configuration Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 123 Sunday, September 9, 2012 6:00 PM
2-124
Display Commandsdisplay ipv6 routing-table protocol
display ipv6 routing-table protocol
Displays routing information for a specified routing protocol. The routing protocol specified may be static, direct or ospfv3.
HP Switch# display ipv6 routing-table protocol directRouting Table: n/a Destinations: 1 Routes: 1
Destination : ::1/128 Protocol : Direct NextHop : ::1 Preference : 0 Interface : InLoop0 Cost : 1
HP Switch# display ipv6 routing-table protocol direct verboseRouting Table: n/a Destinations: 1 Routes: 1
Destination : ::1 PrefixLength : 128 NextHop : ::1 Preference : 0 RelayNextHop : n/a Tag : n/a Neighbor : n/a Process ID : n/a Interface : InLoopBack0 Protocol : Direct State : Active Adv Cost : 1 Tunnel ID : n/a Label : n/a Age : 37221sec
Example of Related ProVision Software Command Output.
HP Switch# show ipv6 route static
IPv6 Route Entries
Destination : 2620:a::/64Gateway : 2620:b::22:1Type : static Sub-Type : NA Distance : 1 Metric : 1
Destination : 2620:c::/64Gateway : 2620:e::55:2Type : static Sub-Type : NA Distance : 1 Metric : 1
Operating Notes
For more information, refer to the latest IPv6 Configuration Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display ipv6 routing-table protocol show ipv6 route {connected | static | ospf3}
Common-CLI-Phase-3-Sept-2012.book Page 124 Sunday, September 9, 2012 6:00 PM
2-125
Display Commandsdisplay lacp system-id
display lacp system-id
Displays the system ID of the local system. The system LACP priority and the system MAC address comprise the system ID.
HP Switch# display lacp system-id
Actor System ID: 0x2f00, 001871-c42f00
Field Descriptions
Actor System ID: The local system ID, including system LACP priority and system MAC address. In the above example:
■ 0x2f00 = System LACP Priority
■ 001871-c42f00 = System MAC Address
Operating Notes
To enable LACP operation in ProVision software, use the following command from the context of a port interface on which you want to enable LACP:
lacp
For more on LACP operation in ProVision software, refer to the “Port Trunking” chapter in the latest Management and Configuration Guide for your switch.
Example of Related ProVision Software Command Output. The ProVi-sion software includes a list of ports configured for LACP operation, along with some additional data fields.
HP Switch(eth-A13-A14)# show lacp local
LACP Local Information.
System ID: 001871-c42f00
LACP Tx Rx Timer Port Trunk Mode Aggregated Timer Expired ---- ------ -------- ----------- ------ -------- A13 A13 Active Yes Fast No A14 A14 Active Yes Fast No
Comware Related ProVision
display lacp system-id show lacp local
Common-CLI-Phase-3-Sept-2012.book Page 125 Sunday, September 9, 2012 6:00 PM
2-126
Display Commandsdisplay lacp system-id
lacp system-id Field Mappings.
Minimum Software Version: 15.08.
Comware ProVision Software
Actor System ID System ID
n/a Port
n/a Trunk
n/a LACP Mode
n/a Aggregated
n/a Tx Timer
n/a Rx Timer Expired
Common-CLI-Phase-3-Sept-2012.book Page 126 Sunday, September 9, 2012 6:00 PM
2-127
Display Commandsdisplay link-aggregation
display link-aggregation
Displays the load-sharing criteria for load-sharing link-aggregation (trunk) groups.
N o t e Link-aggregation in ProVision software is termed port trunking. Load-shar-
ing is termed load-balancing.
When load-balancing is configured as L4-based, the load-sharing mode includes source and destination MAC address, source and destination IP address, and source and destination TCP/UDP port number, as shown below.
HP Switch(config)# display link-aggregation load-sharing mode Layer 4 traffic: destination-mac address, source-mac address, destination-ip address, source-ip address, destination-port, source-port
When load-balancing is configured as L3-based, the load-sharing mode includes source and destination MAC address, and source and destination IP address, as shown below.
HP Switch(config)# display link-aggregation load-sharing mode Layer 3 traffic: destination-mac address, source-mac address destination-ip address, source-ip address
Operating Notes
To enable trunk load-balancing in ProVision software, use the following command in the global configuration context:
trunk < port-list > trkn trunk
trunk-load-balance < L3-based | L4-based >
For more on trunk load-balancing, refer to the “Port Trunking” chapter in the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.08.
Comware Related ProVision
display link-aggregation load-sharing mode n/a
Common-CLI-Phase-3-Sept-2012.book Page 127 Sunday, September 9, 2012 6:00 PM
2-128
Display Commandsdisplay link-aggregation member-port
display link-aggregation member-port
Displays the detailed link aggregation information of the specified member ports or all member ports if no port is specified.
For a member port in a static aggregation group, only the port number and operational key are displayed, because the aggregation group is unaware of information about the peer groups.
Field Descriptions
Flags: One-octet LACP state flags field:
• A indicates whether LACP is enabled. 1 for enabled and 0 for disabled.
Comware Related ProVision
display link-aggregation member-portdisplay link-aggregation member-port GigabitEthernet <port-number>
No equivalent ProVision software command
HP Switch# display link-aggregation member-port
Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation, D -- Synchronization, E -- Collecting, F -- Distributing, G -- Defaulted, H -- Expired
1:Aggregation Interface: Trk1Port Number: 1Oper-Key: 1
2:Aggregation Interface: Dyn1Local: Port Number: 2 Port Priority: 32768 Oper-Key: 2 Flag: n/aRemote: System ID: 0x8000, 0000-0000-0000 Port Number: 0 Port Priority: 32768 Oper-Key: 0 Flag: n/aReceived LACP Packets: 0 packet(s)Illegal: 0 packet(s)Sent LACP Packets: 0 packet(s)
Common-CLI-Phase-3-Sept-2012.book Page 128 Sunday, September 9, 2012 6:00 PM
2-129
Display Commandsdisplay link-aggregation member-port
• B indicates the timeout control value. 1 for short timeout, and 0 for long timeout.
• C indicates whether the link is considered as aggregatable by the sending system. 1 for true, and 0 for false.
• D indicates whether the link is considered as synchronized by the sending system. 1 for true, and 0 for false.
• E indicates whether the sending system considers that collection of incoming frames is enabled on the link. 1 for true and 0 for false.
• F indicates whether the sending system considers that distribution of outgoing frames is enabled on the link. 1 for true and 0 for false.
• G indicates whether the receive state machine of the sending system is using default operational partner information. 1 for true and 0 for false.
• H indicates whether the receive state machine of the sending system is in the expired state. 1 for true and 0 for false.
If a flag bit is set to 1, the corresponding English letter that otherwise is not output is displayed.
Aggregation Interface: Aggregate interface to which the port belongs.
Port Priority: Aggregation priority of the port.
Oper-key: Operational key.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 129 Sunday, September 9, 2012 6:00 PM
2-130
Display Commandsdisplay link-aggregation summary
display link-aggregation summary
Displays the summary information of all aggregation groups.
Information about the remote system for a static link aggregation group may be either shown as none or not displayed, because the aggregation group is unaware of information about the peer groups.
Field Descriptions
Aggregation Interface Type: Aggregate interface type:
• BAGG for a Layer 2 aggregate interface.
• RAGG for a Layer 3 aggregate interface.
Aggregation Mode: Aggregation group type:
• S for static link aggregation.
• D for dynamic aggregation.
Loadsharing Type: Loadsharing type:
• Shar for load sharing.
• NonS for non-load sharing.
Actor System ID: Local system ID, which comprises the system LACP priority and the system MAC address.
Comware Related ProVision
display link-aggregation summary No equivalent ProVision software command
HP Switch# display link-aggregation summary
Aggregation Interface Type:BAGG -- Bridge-Aggregation, RAGG -- Route-AggregationAggregation Mode: S -- Static, D -- DynamicLoadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing
Actor System ID: 0x43c0, 0017a4-ff43c0
AGG AGG Partner ID Select Unselect ShareInterface Mode Ports Ports Type-------------------------------------------------------------------------Dyn1 D 0x0, 0017a4-7eef40 n/a n/a n/a
Common-CLI-Phase-3-Sept-2012.book Page 130 Sunday, September 9, 2012 6:00 PM
2-131
Display Commandsdisplay link-aggregation summary
AGG Interface: Type and number of the aggregate interface.
Partner ID: System ID of the partner, which comprises the system LACP priority and the system MAC address. AGG Mode: Aggregation group type.
Select Ports: The number of Selected ports.
Unselect Ports: The number of Unselected ports.
Share Type: Load sharing type.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 131 Sunday, September 9, 2012 6:00 PM
2-132
Display Commandsdisplay link-aggregation verbose
display link-aggregation verbose
Displays detailed information about the aggregation groups corresponding to the aggregate interfaces in the system.
To display the information of a specific Layer 2 aggregation group, use the display link-aggregation verbose bridge-aggregation bridge-aggregation-number command.
To display the information of all Layer 2 aggregate interfaces, use the display link-aggregation verbose bridge-aggregation command.
Comware Related ProVision
display link-aggregation verbosedisplay link-aggregation verbose Bridge-aggregationdisplay link-aggregation verbose Bridge-aggregation <aggregation-id>
No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 132 Sunday, September 9, 2012 6:00 PM
2-133
Display Commandsdisplay link-aggregation verbose
Field Descriptions
Loadsharing Type: Loadsharing type:
• Shar for load sharing.
• NonS for non-load sharing.
Port Status: Port state: Selected or unselected.
Flags: One-octet LACP state flags field:
• A indicates whether LACP is enabled. 1 for enabled and 0 for disabled.
• B indicates the timeout control value. 1 for short timeout, and 0 for long timeout.
• C indicates whether the link is considered as aggregatable by the sending system. 1 for true, and 0 for false.
• D indicates whether the link is considered as synchronized by the sending system. 1 for true, and 0 for false.
• E indicates whether the sending system considers that collection of incoming frames is enabled on the link. 1 for true and 0 for false.
HP Switch# display link-aggregation verbose bridge-aggregation
Loadsharing Type: Shar -- Loadsharing, NonS -- Non-LoadsharingPort Status: S -- Selected, U -- UnselectedFlags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation, D -- Synchronization, E -- Collecting, F -- Distributing, G -- Defaulted, H -- Expired
Aggregation Interface: Trk1Aggregation Mode: StaticLoadsharing Type: Shar Port Status Oper-Key--------------------------------------------------------------------------- A1 n/a 1
Aggregation Interface: Dyn1Aggregation Mode: DynamicLoadsharing Type: SharSystem ID: noneLocal: Port Status Priority Oper-Key Flag---------------------------------------------------------------------------- A2 n/a 32768 2 n/aRemote: Actor Partner Priority Oper-Key SystemID Flag---------------------------------------------------------------------------- A2 0 32768 0 n/a n/a
Common-CLI-Phase-3-Sept-2012.book Page 133 Sunday, September 9, 2012 6:00 PM
2-134
Display Commandsdisplay link-aggregation verbose
• F indicates whether the sending system considers that distribution of outgoing frames is enabled on the link. 1 for true and 0 for false.
• G indicates whether the receive state machine of the sending system is using default operational partner information. 1 for true and 0 for false.
• H indicates whether the receive state machine of the sending system is in the expired state. 1 for true and 0 for false.
If a flag bit is set to 1, the corresponding English letter that otherwise is not output is displayed.
Aggregation Interface: Name of the aggregate interface.
Aggregation Mode: Type of the aggregation group:
• Static for static aggregation.
• Dynamic for dynamic aggregation.
Port: Port type and number.
Status: State of the port.
Oper-Key: Operational key value.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 134 Sunday, September 9, 2012 6:00 PM
2-135
Display Commandsdisplay lldp local-information
display lldp local-information
Displays the LLDP information. This includes the global information and per interface information.
HP Switch# display lldp local-informationGlobal LLDP local-information Chassis ID : 0000-0000-1122 System name : HP-E3500yl-48G System description : HP J8693A Switch E3500yl-48G, revision K.15.09.0000x, ROMK.15.28 HP-3500yl-48GCopyright (C) 1991-2012 Hewlett-Packard Development Company, L.P. System capabilities supported : Bridge, Router System capabilities enabled : Bridge
MED information device class : network Connectivity //This is intentional (MED inventory information of master board)
HardwareRev : Rev 0 FirmwareRev : K.15.28 SoftwareRev : K.15.09.0000x SerialNum : SG729TH003 Manufacturer name : Hewlett-Packard Model name : J8693A Asset tracking identifier : Unknown
LLDP local-information of port 1 : Port ID subtype : local Port ID : 1 Port description : 1
Management address type : ipv4 Management address : 1.2.3.4 Management address interface type : ipv6 Management address interface ID : 578 Management address OID : 0
Port VLAN ID(PVID) : 1
Comware Related ProVision
display lldp local-information No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 135 Sunday, September 9, 2012 6:00 PM
2-136
Display Commandsdisplay lldp local-information
Port and protocol VLAN ID(PPVID) : n/a port and protocol VLAN supported : n/a Port and protocol VLAN enabled : n/a
VLAN name of VLAN 1 : n/a
Auto-negotiation supported : Yes Auto-negotiation enabled : Yes OperMau : 30
PoE supported : n/a
Link aggregation supported : n/a Link aggregation enabled : n/a Aggregation port ID : n/a
Maximum frame Size : n/a
Media policy type : voice Signaling Unknown Policy : No VLAN tagged : No Media policy VlanID : 1 Media policy L2 priority : 6 Media policy Dscp : 46
LLDP local-information of port 2 : Port ID subtype : local Port ID : 2 Port description : 2
Management address type : ipv4 Management address : 10.0.0.5 Management address interface type : ipv6 Management address interface ID : 578 Management address OID : zeroDotZero
Port VLAN ID(PVID) : 1
Port and protocol VLAN ID(PPVID) : n/a port and protocol VLAN supported : n/a Port and protocol VLAN enabled : n/a
VLAN name of VLAN <number> : n/a
Auto-negotiation supported : Yes Auto-negotiation enabled : Yes
Common-CLI-Phase-3-Sept-2012.book Page 136 Sunday, September 9, 2012 6:00 PM
2-137
Display Commandsdisplay lldp local-information
OperMau : 30
PoE supported : n/a
Link aggregation supported : n/a Link aggregation enabled : n/a Aggregation port ID : n/a
Maximum frame Size : n/a
Media policy type : voice Signaling Unknown Policy : No VLAN tagged : No Media policy VlanID : 1 Media policy L2 priority : 6 Media policy Dscp : 46
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 137 Sunday, September 9, 2012 6:00 PM
2-138
Display Commandsdisplay lldp local-information global
display lldp local-information global
Displays LLDP system global information.
HP Switch# display lldp local-information global
Global LLDP local-information Chassis ID : 0000-0000-1122/00 System name : HP-E3500yl-48G System description : HP J8693A Switch E3500yl-48G, revision K.15.09.0000x, ROMK.15.28HP-3500yl-48GCopyright (C) 1991-2012 Hewlett-Packard Development Company, L.P. System capabilities supported : Bridge, Router System capabilities enabled : Bridge
MED information device class : network Connectivity (MED inventory information of master board)
HardwareRev : Rev 0 FirmwareRev : K.15.28 SoftwareRev : K.15.09.0000x SerialNum : SG729TH003 Manufacturer name : Hewlett-Packard Model name : J8693A Asset tracking identifier : Unknown
Minimum Software Version: 15.09.
Comware Related ProVision
display lldp local-information global No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 138 Sunday, September 9, 2012 6:00 PM
2-139
Display Commandsdisplay lldp local-information interface interface-type interface-number
display lldp local-information interface interface-type interface-number
Displays LLDP detailed information for a given interface.
HP Switch# display lldp local-information interface 47LLDP local-information of port 47 : Port ID subtype : local Port ID : 47 Port description : 47
Management address type : ipv4 Management address : 1.2.3.4 Management address interface type : ipv6 Management address interface ID : 578 Management address OID : 0
Port VLAN ID(PVID) : 1
Port and protocol VLAN ID(PPVID) : n/a Port and protocol VLAN supported : n/a Port and protocol VLAN enabled : n/a
VLAN name of VLAN 1: n/a
Auto-negotiation supported : Yes Auto-negotiation enabled : Yes OperMau : 30
Power port class : n/a PSE power supported : n/a PSE power enabled : n/a PSE pairs control ability : n/a Power pairs : n/a Port power classification : n/a
Link aggregation supported : n/a Link aggregation enabled : n/a Aggregation port ID : n/a
Comware Related ProVision
display lldp local-information interface interface-type interface-number
No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 139 Sunday, September 9, 2012 6:00 PM
2-140
Display Commandsdisplay lldp local-information interface interface-type interface-number
Maximum frame Size : n/a
MED information Media policy type : voice Signaling Unknown Policy : No VLAN tagged : No Media policy VlanID : 1 Media policy L2 priority : 6 Media policy Dscp : 46
PoE PSE power source : n/a Port PSE Priority : n/a Port available power value : n/a
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 140 Sunday, September 9, 2012 6:00 PM
2-141
Display Commandsdisplay lldp neighbor-information brief
display lldp neighbor-information brief
Displays brief information of all the ports connected to neighbors.
HP Switch# display lldp neighbor-information brief LLDP neighbor-information of port 1 : Neighbor 1: ChassisID/subtype: 0023-4751-ba80/MAC address PortID/subtype : 34/Locally assigned Capabilities : Bridge,Router
LLDP neighbor-information of port 2 :Neighbor 1:
ChassisID/subtype: 0021-f71b-fc40/MAC address PortID/subtype : 1/Locally assigned Capabilities : Bridge,Router
Example of Related ProVision Software Command Output.
HP Switch# show lldp info remote-device A3LLDP Remote Device Information DetailLocal Port : A3ChassisType : mac-addressChassisId : 00 16 35 ff 2d 40PortType : localPortId : 23SysName : HPSwitchSystem Descr : HP Switch 3500-24, revision K.14.xxPortDescr : 23Pvid : 55System Capabilities Supported : bridge, routerSystem Capabilities Enabled : bridgeRemote Management AddressType : ipv4Address : 10.0.102.198Poe Plus Information DetailPoe Device Type : Type2 PDPower Source : Only PSEPower Priority : lowPD Requested Power Value : 20 Watts
Comware Related ProVision
display lldp neighbor-information brief show lldp info remote-device
Common-CLI-Phase-3-Sept-2012.book Page 141 Sunday, September 9, 2012 6:00 PM
2-142
Display Commandsdisplay lldp neighbor-information brief
PSE Actual Power Value : 20 Watts
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 142 Sunday, September 9, 2012 6:00 PM
2-143
Display Commandsdisplay lldp neighbor-information list display lldp neighbor-information list system-name <string>
display lldp neighbor-information list display lldp neighbor-information list system-name <string>
HP Switch# display lldp neighbor_information listSystem Name Local Interface Chassis ID Port IDHP Switch 1 00 0f 90 dc 9f 80 1
Example of Related ProVision Software Command Output.
HP Switch# show lldp info remote-device A3LLDP Remote Device Information DetailLocal Port : A3ChassisType : mac-addressChassisId : 00 16 35 ff 2d 40PortType : localPortId : 23SysName : HPSwitchSystem Descr : HP Switch 3500-24, revision K.14.xxPortDescr : 23Pvid : 55System Capabilities Supported : bridge, routerSystem Capabilities Enabled : bridgeRemote Management AddressType : ipv4Address : 10.0.102.198Poe Plus Information DetailPoe Device Type : Type2 PDPower Source : Only PSEPower Priority : lowPD Requested Power Value : 20 WattsPSE Actual Power Value : 20 Watts
Whereas Comware can accpet multiple strings as input with spaces for system name, ProVision accepts only one string.
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display lldp neighbor-information listdisplay lldp neighbor-information list system-name <string>
show lldp info remote-device
Common-CLI-Phase-3-Sept-2012.book Page 143 Sunday, September 9, 2012 6:00 PM
2-144
Display Commandsdisplay lldp statistics
display lldp statistics
Displays information about LLDP packets that are being advertised by the local system or by remote systems, and global LLDP information followed by each interface in the switch. The statistics refer to significant events that involve LLDP packet transmission and reception.
HP Switch# display lldp statistics LLDP statistics global information:LLDP neighbor information last change time:33 days,19 hours,39 minutes,37 secondsThe number of LLDP neighbor information inserted : 10The number of LLDP neighbor information deleted : 10The number of LLDP neighbor information dropped : 0The number of LLDP neighbor information aged out : 8
LLDP statistics information of port 1 [GigabitEthernet1/0/1]:The number of LLDP frames transmitted : 1713The number of LLDP frames received : 1200The number of LLDP frames discarded : 0The number of LLDP error frames : 1200The number of LLDP TLVs discarded : 1200The number of LLDP TLVs unrecognized : 0The number of LLDP neighbor information aged out : 1The number of CDP frames transmitted : n/aThe number of CDP frames received : n/aThe number of CDP frames discarded : n/aThe number of CDP error frames : n/a
LLDP statistics information of port 2 [GigabitEthernet1/0/2]:The number of LLDP frames transmitted : 2783The number of LLDP frames received : 1211The number of LLDP frames discarded : 0
Example of Related ProVision Software Command Output.
HP Switch# show lldp statsLLDP Device StatisticsNeighbor Entries List Last Updated : 2 hoursNew Neighbor Entries Count : 20Neighbor Entries Deleted Count : 20Neighbor Entries Dropped Count : 0
Comware Related ProVision
display lldp statistics show lldp stats
Common-CLI-Phase-3-Sept-2012.book Page 144 Sunday, September 9, 2012 6:00 PM
2-145
Display Commandsdisplay lldp statistics
Neighbor Entries AgeOut Count : 20LLDP Port StatisticsPort | NumFramesRecvd NumFramesSent NumFramesDiscarded------ + -------------- ------------- ------------------A1 | 97317 97843 0A2 | 21 12 0A3 | 0 0 0A4 | 446 252 0A5 | 0 0 0A6 | 0 0 0A7 | 0 0 0
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 145 Sunday, September 9, 2012 6:00 PM
2-146
Display Commandsdisplay lldp statistics global
display lldp statistics global
Displays global information about LLDP packets that are being advertised by the local system or by remote systems. The statistics refer to significant events that involve LLDP packet transmission and reception.
HP Switch# display lldp statistics globalLLDP statistics global information:LLDP neighbor information last change time:33 days,19 hours,39 minutes,37 secondsThe number of LLDP neighbor information inserted : 10The number of LLDP neighbor information deleted : 10The number of LLDP neighbor information dropped : 0The number of LLDP neighbor information aged out : 8
Example of Related ProVision Software Command Output.
HP Switch# show lldp statsLLDP Device StatisticsNeighbor Entries List Last Updated : 2 hoursNew Neighbor Entries Count : 20Neighbor Entries Deleted Count : 20Neighbor Entries Dropped Count : 0Neighbor Entries AgeOut Count : 20LLDP Port StatisticsPort | NumFramesRecvd NumFramesSent NumFramesDiscarded------ + -------------- ------------- ------------------A1 | 97317 97843 0A2 | 21 12 0A3 | 0 0 0A4 | 446 252 0A5 | 0 0 0A6 | 0 0 0A7 | 0 0 0
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display lldp statistics global show lldp stats
Common-CLI-Phase-3-Sept-2012.book Page 146 Sunday, September 9, 2012 6:00 PM
2-147
Display Commandsdisplay lldp statistics interface interface-type interface-number
display lldp statistics interface interface-type interface-number
Displays information about LLDP packets on a particular interface that are being advertised by the local system or by remote systems. The statistics refer to significant events that involve LLDP packet transmission and reception.
HP Switch# display lldp statistics interface 1LLDP statistics information of port 1 [GigabitEthernet1/0/1]:The number of LLDP frames transmitted : 1713The number of LLDP frames received : 1200The number of LLDP frames discarded : 0The number of LLDP error frames : 1200The number of LLDP TLVs discarded : 1200The number of LLDP TLVs unrecognized : 0The number of LLDP neighbor information aged out : 1The number of CDP frames transmitted : n/aThe number of CDP frames received : n/aThe number of CDP frames discarded : n/aThe number of CDP error frames : n/a
Example of Related ProVision Software Command Output.
HP Switch# show lldp statsLLDP Device StatisticsNeighbor Entries List Last Updated : 2 hoursNew Neighbor Entries Count : 20Neighbor Entries Deleted Count : 20Neighbor Entries Dropped Count : 0Neighbor Entries AgeOut Count : 20LLDP Port StatisticsPort | NumFramesRecvd NumFramesSent NumFramesDiscarded------ + -------------- ------------- ------------------A1 | 97317 97843 0A2 | 21 12 0A3 | 0 0 0A4 | 446 252 0A5 | 0 0 0A6 | 0 0 0A7 | 0 0 0
Comware Related ProVision
display lldp statistics interface interface-type interface-number
show lldp stats
Common-CLI-Phase-3-Sept-2012.book Page 147 Sunday, September 9, 2012 6:00 PM
2-148
Display Commandsdisplay lldp statistics interface interface-type interface-number
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 148 Sunday, September 9, 2012 6:00 PM
2-149
Display Commandsdisplay lldp status
display lldp status
Displays information about Link Layer Discovery Protocol (LLDP) and Link Level Discovery Protocol-Media Endpoint Discovery (LLDP-MED) configura-tion and capabilities on the switch. LLDP and LLDP-MED are used to learn about and to distribute device information on network links. This command shows information on global level as well as the interface level.
HP Switch# display lldp statusThe current number of LLDP neighbors: 0The current number of CDP neighbors: 0LLDP neighbor information last changed time: 33 days,19 hours,39 minutes,37 secondsTransmit interval : 30sHold multiplier : 4Reinit delay : 2sTransmit delay : 2sTrap interval : 5sFast start times : 3
Port 1 [GigabitEthernet1/0/1]:Port status of LLDP : EnableAdmin status : Tx_RxTrap flag : NoPolling interval : 0s
Number of neighbors: : 0Number of MED neighbors : 0Number of CDP neighbors : 0Number of sent optional TLV : 0Number of received unknown TLV : 0
Minimum Software Version: 15.09.
Comware Related ProVision
display lldp status No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 149 Sunday, September 9, 2012 6:00 PM
2-150
Display Commandsdisplay lldp status interface interface-type interface number
display lldp status interface interface-type interface number
Displays information about Link Layer Discovery Protocol (LLDP) and Link Level Discovery Protocol-Media Endpoint Discovery (LLDP-MED) configura-tion and capabilities on the switch. LLDP and LLDP-MED are used to learn about and to distribute device information on network links.
HP Switch# display lldp status interface 1
Port 1 :Port status of LLDP : EnableAdmin status : Tx_RxTrap flag : NoPolling interval : 0s
Number of neighbors: 0Number of MED neighbors : 0Number of CDP neighbors : 0Number of sent optional TLV : 0Number of received unknown TLV : 0
Minimum Software Version: 15.10.
Comware Related ProVision
display lldp status interface interface-type interface number
No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 150 Sunday, September 9, 2012 6:00 PM
2-151
Display Commandsdisplay lldp tlv-config interface interface-type interface-number
display lldp tlv-config interface interface-type interface-number
LLDP information is sent by devices from each of their interfaces at a fixed interval in the form of an Ethernet frame. Each frame contains one Link Layer Discovery Protocol Data Unit (LLDPDU). Each LLDPDU is a sequence of type-length-value (TLV) structures. Each LLDP frame starts with the following mandatory TLVs: Chassis ID, Port ID, and Time-to-Live. The mandatory TLVs are followed by any number of optional TLVs. All Optional TLVs can be configured per port basis and can be displayed with the help of this command for a particular interface.
HP Switch# display lldp tlv-configLLDP tlv-config of port 98[GigabitEthernet2/0/2]:NAME STATUS DEFAULTBasic optional TLV:Port Description TLV YES YESSystem Name TLV YES YESSystem Description TLV YES YESSystem Capabilities TLV YES YESManagement Address TLV YES YES
IEEE 802.1 extend TLV:Port VLAN ID TLV YES YESPort And Protocol VLAN ID TLV YES YESVLAN Name TLV YES YES
IEEE 802.3 extend TLV:MAC-Physic TLV YES YESPower via MDI TLV YES YESLink Aggregation TLV YES YESMaximum Frame Size TLV YES YES
LLDP-MED extend TLV:Capabilities TLV YES YESNetwork Policy TLV YES YESLocation Identification TLV NO NOExtended Power via MDI TLV YES YESInventory TLV YES YES
Minimum Software Version: 15.09.
Comware Related ProVision
display lldp tlv-config interface interface-type interface-number
No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 151 Sunday, September 9, 2012 6:00 PM
2-152
Display Commandsdisplay logfile buffer
display logfile buffer
Displays system log information.
HP Switch# display logfile buffer
%@00061%Jan 01 00:00:47 2090 system: --------------------------
%@00062%Jan 01 00:00:47 2090 system: Mgmt Module 1 went down without saving crash information
%@03002%Jan 01 00:00:47 2090 system: System reboot due to Reset Switch
%@02759%Jan 01 00:00:47 2090 chassis: Savepower LED timer is OFF.
%@00433%Jan 01 00:00:47 2090 ssh: Ssh server enabled
%@00092%Jan 01 00:00:47 2090 dhcp: Enabling Auto Image Config Download via DHCP and turning off auto-tftp if enabled
%@00690%Jan 01 00:00:48 2090 udpf: DHCP relay agent feature enabled
%@02637%Jan 01 00:00:48 2090 srcip: TACACS admin policy is 'outgoing interface'
%@02638%Jan 01 00:00:48 2090 srcip: TACACS oper policy is 'outgoing interface'
%@02637%Jan 01 00:00:48 2090 srcip: RADIUS admin policy is 'outgoing interface'
%@02638%Jan 01 00:00:48 2090 srcip: RADIUS oper policy is 'outgoing interface'
%@02637%Jan 01 00:00:48 2090 srcip: SYSLOG admin policy is 'outgoing interface'
%@02638%Jan 01 00:00:48 2090 srcip: SYSLOG oper policy is 'outgoing interface'
%@02637%Jan 01 00:00:48 2090 srcip: TELNET admin policy is 'outgoing
Comware Related ProVision
display logfile buffer show logging
Common-CLI-Phase-3-Sept-2012.book Page 152 Sunday, September 9, 2012 6:00 PM
2-153
Display Commandsdisplay logfile buffer
Example of Related ProVision Software Command Output.
HP Switch# show loggingKeys: W=Warning I=Information M=Major D=Debug E=Error---- Event Log listing: Events Since Boot ----
I 10/28/09 21:45:42 00061 system: AM1: ------------------------
I 10/28/09 21:45:42 00062 system: AM1: Mgmt Module 1 went down without saving crash information
M 10/28/09 21:45:42 03002 system: AM1: System reboot due to Reset Switch
I 10/28/09 21:45:42 02759 chassis: AM1: Savepower LED timer is OFF.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot A configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot B configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot C configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot D configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot E configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot F configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot G configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot H configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot I configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot J configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot K configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot L configured ON.
I 10/28/09 21:45:42 00937 chassis: AM1: Fabric 1 inserted
Common-CLI-Phase-3-Sept-2012.book Page 153 Sunday, September 9, 2012 6:00 PM
2-154
Display Commandsdisplay logfile buffer
I 10/28/09 21:45:42 00937 chassis: AM1: Fabric 2 inserted
I 10/28/09 21:45:43 00092 dhcp: AM1: Enabling Auto Image Config Download via DHCP and turning off auto-tftp if enabled
I 10/28/09 21:45:43 00690 udpf: AM1: DHCP relay agent feature enabled
I 10/28/09 21:45:43 02637 srcip: AM1: TACACS admin policy is 'outgoing interface'
I 10/28/09 21:45:43 02638 srcip: AM1: TACACS oper policy is 'outgoing interface'
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 154 Sunday, September 9, 2012 6:00 PM
2-155
Display Commandsdisplay loopback-detection
display loopback-detection
Displays the operating status of the loopback detection function.
Field Descriptions
Detection Interval: Loopback detection interval in seconds.
Action Mode: The loopback detection action:
• None—When detecting a looped port, the system prints log informa-tion and sends trap messages.
• Shutdown—When detecting a looped port, the system prints log information, sends trap messages, and shuts down the port.
There is no related ProVision command.
Minimum Software Version: 15.09.
Comware Related ProVision
display loopback-detection No equivalent ProVision software command
HP Switch(config)# display loopback-detection
Loopback-detection is running. Detection interval is 30 second(s). Action mode: None Loopback-detection is enabled on the following VLAN(s): 1, 20, 315, 1001, 2008, 2010-2015, 2026 Loopback is detected on the following interface(s): 1 2 3 10
Common-CLI-Phase-3-Sept-2012.book Page 155 Sunday, September 9, 2012 6:00 PM
2-156
Display Commandsdisplay mac-address
display mac-address
Displays information about the MAC address table.
HP Switch# display mac-address
MAC ADDR VLAN ID STATE PORT INDEX AGING TIME(s)001635-22ca40 1 Learned A1 AGING001635-22ca7f 1 Learned A1 AGING001122-334455 2 Config static A2 NOAGED
--- 3 mac address(es) found ---
Example of Related ProVision Software Command Output.
HP Switch# show mac-address 000009-21ae04Status and Counters - Address Table - 080009-21ae84MAC Address : 080009-21ae84Locate on Port : A2
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display mac-address show mac-address
Common-CLI-Phase-3-Sept-2012.book Page 156 Sunday, September 9, 2012 6:00 PM
2-157
Display Commandsdisplay mac-address aging-time
display mac-address aging-time
Displays the aging time of dynamic entries in the MAC address table.
Field Descriptions
Mac address aging time: Aging time of dynamic entries in the MAC address table.
Operating Notes
Comware displays mac-address as 1234-1234-1234 and ProVision displays it as 123456-123456.
For more information about MAC aging time, see the “Interface Access and System Information” chapter in the latest Basic Operation Guide for your switch.
Example of Related ProVision Software Command Output.
Comware Related ProVision
display mac-address aging-time show system information
HP Switch# display mac-address aging-timeMac address aging time: 300s
HP Switch# show system information
Status and Counters - General System Information
System Name : HP Switch System Contact : System Location :
MAC Age Time (sec) : 300
Time Zone : 0 Daylight Time Rule : None
Common-CLI-Phase-3-Sept-2012.book Page 157 Sunday, September 9, 2012 6:00 PM
2-158
Display Commandsdisplay mac-address aging-time
display mac-address aging-time Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
Mac address aging time MAC Age Time (sec)
Common-CLI-Phase-3-Sept-2012.book Page 158 Sunday, September 9, 2012 6:00 PM
2-159
Display Commandsdisplay mac-address multicast
display mac-address multicast
Displays static multicast MAC address entries.
HP Switch# display mac-address multicastMAC ADDR VLAN ID STATE PORT INDEX AGING TIME(s)010122-334455 1 Multicast A1 NOAGED012222-334455 1 Multicast F24 NOAGED
--- 2 mac address(es) found ---
Minimum Software Version: 15.10.
Comware Related ProVision
display mac-address multicast No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 159 Sunday, September 9, 2012 6:00 PM
2-160
Display Commandsdisplay mac-authentication
display mac-authentication
Displays MAC authentication settings and statistics, including the global settings, and port-specific settings and MAC authentication and online user statistics.
If you specify a list of ports, the command displays port-specific settings and statistics only for the specified ports.
If you do not specify any port, the command displays port-specific settings and statistics for all ports.
Comware Related ProVision
display mac-authentication [interface] show port-access mac-based
Common-CLI-Phase-3-Sept-2012.book Page 160 Sunday, September 9, 2012 6:00 PM
2-161
Display Commandsdisplay mac-authentication
Field Descriptions
MAC address authentication is enabled: Whether MAC authentication is enabled.
User name format is no-delimiter like no delimiter format: Type of user account, which can be MAC-based or shared. If MAC-based accounts are used, this field displays “User name format is MAC address …” and the format settings for usernames and passwords. For example, MAC addresses without hyphens in lower case. If a shared account is used, this field displays “User name format is fixed account.”
Fixed username: Username of the shared account for MAC authentication users. If MAC-based accounts are used, this field displays mac.
Fixed password: Password of the shared account for MAC authentication users. If MAC-based accounts are used, this field displays not configured.
Offline detect period: Setting of the offline detect timer.
Quiet period: Setting of the quiet timer.
HP Switch(config)# display mac-authentication
MAC address authentication is n/a User name format is no-delimiter like aabbccddeeff Fixed Username:n/a Fixed password:not configured Offline detect period is 0s Quiet period is 0s Server response timeout value is 0s The max allowed user number is n/a per slot Current user number amounts to 0 Current domain: n/a
Silent MAC User info: MAC Addr From Port Port Index n/a n/a n/a
A1 is link-up MAC address authentication is disabled Authenticate success: n/a, failed: n/a Max number of on-line users is 1 Current online user number is 0 MAC Addr Authenticate state AuthIndexA2 is link-down MAC address authentication is disabled Authenticate success: n/a, failed: n/a Max number of on-line users is 1 Current online user number is 0 MAC Addr Authenticate state AuthIndex
Common-CLI-Phase-3-Sept-2012.book Page 161 Sunday, September 9, 2012 6:00 PM
2-162
Display Commandsdisplay mac-authentication
Server response timeout value: Setting of the server timeout timer.
The max allowed user number: Maximum number of users each slot supports.
Current user number amounts to: Number of online users.
Current domain: not configured, use default domain: Authentication domain that is currently used.
Silent Mac User info: Information about silent MAC addresses. A MAC address is marked silent when it fails a MAC authentication, and at the same time, a quiet timer starts. Before the timer expires, the device drops any packet from the MAC address and does not perform MAC authentication for the MAC address.
GigabitEthernet3/0/1 is link-up: Status of the link on port GigabitEthernet 3/0/1. In this example, the link is up.
MAC address authentication is enabled: Whether MAC authentication is enabled on port GigabitEthernet 3/0/1.
Authenticate success: 0, failed: 0: MAC authentication statistics, including the number of successful and unsuccessful authentication attempts.
Current online user number: Number of online users on the port.
MAC Addr: MAC address of the online user.
Authenticate state: User status. Possible values include the following:
• CONNECTING—The user is logging in.
• SUCCESS—The user has passed the authentication.
• FAILURE—The user failed the authentication.
• LOGOFF—The user has logged off.
AuthIndex: Authenticator index.
Operating Notes
For more information on switch MAC authentication operation, see the “Web and MAC Authentication” chapter in the latest Access Security Guide for your switch.
Common-CLI-Phase-3-Sept-2012.book Page 162 Sunday, September 9, 2012 6:00 PM
2-163
Display Commandsdisplay mac-authentication
Example of Related ProVision Software Command Output.
display mac-authentication [interface] Field Mappings.
HP Switch(config)# show port-access mac-based
Port Access MAC-Based Status
Auth Unauth Untagged Tagged Port % In RADIUS Port Clients Clients VLAN VLANs COS Limit ACL ---- ------- ------- -------- ------ -------- ------ ------ 1 1 1 2003 Yes 70000000 100 Yes 2 2 0 MACbased No Yes Yes Yes 3 4 0 1 Yes No No No
Comware ProVision Software
MAC address authentication is enabled n/a
User name format is MAC address in lowercase, like xxxxxxxxxxxx
n/a
Fixed username n/a
Fixed password n/a
Offline detect period n/a
Quiet period n/a
Server response timeout value n/a
the max allowed user number n/a
Current user number amounts to n/a
Current domain: not configured, use default domain
n/a
Silent Mac User info n/a
GigabitEthernet3/0/1 is link-up n/a
MAC address authentication is enabled n/a
Authenticate success: 0, failed: 0 n/a
Current online user number n/a
MAC Addr n/a
Common-CLI-Phase-3-Sept-2012.book Page 163 Sunday, September 9, 2012 6:00 PM
2-164
Display Commandsdisplay mac-authentication
Minimum Software Version: 15.09.
Authenticate state n/a
AuthIndex n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 164 Sunday, September 9, 2012 6:00 PM
2-165
Display Commandsdisplay mac-authentication [interface …]
display mac-authentication [interface …]
Displays MAC authentication settings and statistics.
HP Switch# display mac-authentication interface configurationMAC address authentication is n/a User name format is no-delimiter like aabbccddeeff Fixed Username:n/a Fixed password:not configured Offline detect period is 0s Quiet period is 0s Server response timeout value is 0s The max allowed user number is n/a per slot Current user number amounts to 0 Current domain: n/aSilent MAC User info: MAC Addr From Port Port Index n/a n/a n/aA1 is link-up MAC address authentication is disabled Authenticate success: n/a, failed: n/a Max number of on-line users is 1 Current online user number is 0 MAC Addr Authenticate state AuthIndexA2 is link-down MAC address authentication is disabled Authenticate success: n/a, failed: n/a Max number of on-line users is 1 Current online user number is 0 MAC Addr Authenticate state AuthIndex
Example of Related ProVision Software Command Output.
HP Switch# show port-access mac-based config
Port Access MAC-Based Configuration
MAC Address Format : no-delimiterPassword : secretMAC1
Unauth Redirect Configuration URL :
Unauth Redirect Client Timeout (sec) : 1800
Comware Related ProVision
display mac-authentication [interface ...] show port-access mac-based
Common-CLI-Phase-3-Sept-2012.book Page 165 Sunday, September 9, 2012 6:00 PM
2-166
Display Commandsdisplay mac-authentication [interface …]
Unauth Redirect Restrictive Filter : DisabledTotal Unauth Redirect Client Count : 0
Client Client Logoff Re-Auth Unauth Auth CntrlPort Enabled Limit Moves Period Period VLAN ID VLAN ID Dir
---- ------- ------ ------ ------- ------- ------- -------- -----1 No 1 No 300 0 0 0 both2 No 1 No 300 0 0 0 both3 No 1 No 300 0 0 0 both4 No 1 No 300 0 0 0 both5 No 1 No 300 0 0 0 both6 No 1 No 300 0 0 0 both7 No 1 No 300 0 0 0 both8 No 1 No 300 0 0 0 both
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 166 Sunday, September 9, 2012 6:00 PM
2-167
Display Commandsdisplay memory
display memory
Displays the current memory usage on the switch.
HP Switch(config)# display memory System Total Memory(bytes): 128090112 Total Used Memory(bytes): 47385504 Used Rate: 36%
Field Descriptions
System Total Memory (bytes): Total system memory in the switch.
Total Used Memory (bytes): Total system memory in use.
Used Rate: Percentage of system memory in use.
Operating Notes
To display memory usage in ProVision Software, use the following command:
HP Switch# show system information
This command lists the total memory and free memory available in the switch, along with other system-related information.
For more on system information, refer to the “Interface Access and System Information” chapter in the latest Basic Operation Guide for your switch.
Comware Related ProVision
display memory show system information
Common-CLI-Phase-3-Sept-2012.book Page 167 Sunday, September 9, 2012 6:00 PM
2-168
Display Commandsdisplay memory
Example of Related ProVision Software Command Output.
Minimum Software Version: 15.08.
HP Switch# show system information
Status and Counters - General System Information
System Name : HP Switch System Contact : System Location :
MAC Age Time (sec) : 300
Time Zone : -480 Daylight Time Rule : Continental-US-and-Canada
Software revision : K.15.08.0003 Base MAC Addr : 001871-c42f00 ROM Version : K.15.27 Serial Number : SG641SU00L Allow V1 Modules : Yes Opacity Shields : Not Installed
Up Time : 3 hours Memory - Total : 128,040,960 CPU Util (%) : 0 Free : 80,694,816
IP Mgmt - Pkts Rx : 126,890 Packet - Total : 6750 Pkts Tx : 5123 Buffers Free : 5086 Lowest : 5051 Missed : 0
Common-CLI-Phase-3-Sept-2012.book Page 168 Sunday, September 9, 2012 6:00 PM
2-169
Display Commandsdisplay mld group
display mld group
Displays the number of active MLD (Multicast Listener Discovery) groups and the VLAN and IPv6 address on which each group is active.HP Switch# display mld group Total 4 MLD Group(s).Interface group report information Vlan-Interface1(1234:1::5): Total 1 MLD Groups reported Group Address : ff1e::1 Last Reporter : fe80::200:f7ff:fe95:4f5d Uptime : 00:45:00 Expires : 00:03:20 Vlan-Interface2(1234:3::5): Total 2 MLD Groups reported Group Address : ff1e::3 Last Reporter : fe80::200:f7ff:fe95:da95 Uptime : 00:43:28 Expires : 00:03:16 Group Address : ff1e::4 Last Reporter : fe80::200:f7ff:fe95:da95 Uptime : 00:43:28 Expires : 00:03:16 Vlan-Interface10(1234:2::5): Total 1 MLD Groups reported Group Address : ff1e::5 Last Reporter : fe80::200:f7ff:fe95:9c92 Uptime : 00:43:41 Expires : 00:03:20
Comware Related ProVision
display mld group show ipv6 mld
Common-CLI-Phase-3-Sept-2012.book Page 169 Sunday, September 9, 2012 6:00 PM
2-170
Display Commandsdisplay mld group
Field Descriptions
Total n MLD Groups: The total number of MLD groups detected on the switch.
VLAN-interface< id > ( < ipv6-addr > ): A specific VLAN interface
Total n MLD Groups reported: The number of MLD groups detected on the indicated VLAN.
Group Address: The IPv6 address of an MLD group detected on the indicated VLAN.
• Last Reporter: The IPv6 address of the host that last reported member-ship for the group.
• Uptime: Length of time since the IPv6 multicast group was joined.
• Expires: Time remaining for the IPv6 multicast group.
Operating Notes
The display mld group command reports on MLD traffic on static VLANs.
The switch supports MLDv1 and MLDv2.
To enable MLD operation in ProVision software, use the following command in a VLAN configuration context:
ipv6 mld < enable | disable >
For example:
HP Switch(vlan-10)# ipv6 mld enable
For more on MLD, including additional MLD commands, see the “Multicast Listener Discovery (MLDv1 and MLDv2)” chapter in the latest IPv6 Configu-
ration Guide for your switch.
Common-CLI-Phase-3-Sept-2012.book Page 170 Sunday, September 9, 2012 6:00 PM
2-171
Display Commandsdisplay mld group
Example of Related ProVision Software Command Output.
HP Switch(config)# show ipv6 mld
MLD Service Protocol Info
Total vlans with MLD enabled : 2 Current count of multicast groups joined : 2
VLAN ID : 1 NAME : DEFAULT_VLAN MLD Version : 2
MLD Interface State : Querier Querier Address : fe80::218:71ff:fec4:2f00 [this switch] Version : 2 Uptime : 11m 55s Expires : 1m 5s Ports with multicast routers :
Active Group Addresses Tracking Vers Mode Uptime Expires ---------------------------------------- -------- ---- ---- -------- -------- ff3e:30:2001:db8:8:0:7:101 Filtered 2 EXC 20h 55m 22h 50m VLAN ID : 2 NAME : VLAN2 MLD Version : 2
MLD Interface State : Non-Querier Querier Address : :: Version : - Uptime : - Expires : - Ports with multicast routers :
Active Group Addresses Tracking Vers Mode Uptime Expires ---------------------------------------- -------- ---- ---- -------- -------- ff33:30:2001:db8:8:0:7:102 Filtered 2 INC 10m 40s 12m 17s
Common-CLI-Phase-3-Sept-2012.book Page 171 Sunday, September 9, 2012 6:00 PM
2-172
Display Commandsdisplay mld group
mld group Field Mappings.
Minimum Software Version: 15.08.
Comware ProVision
n/a Total vlans with MLD enabled
Total n mld Group(s) Current count of multicast groups joined
Vlan Interfacen(ipv6-addr) VLAN ID Active Group Addresses
Total n MLD Groups reported n/a
n/a NAME
n/a MLD Version
n/a MLD Interface State
n/a Tracking Vers Mode Uptime Expires
Common-CLI-Phase-3-Sept-2012.book Page 172 Sunday, September 9, 2012 6:00 PM
2-173
Display Commandsdisplay mld group interface vlan-interface <vid>
display mld group interface vlan-interface <vid>
Displays information of all MLD groups.
HP Switch# display mld group interface vlan-interface 30Interface group report informationVlan-Interface30(2075:1:1:30::1): Total 5 MLD Groups reported Group : ff02::2 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:18 Group : ff02::16 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:26 Group : ff02::1:ff00:0 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:26 Group : ff02::1:ff00:3 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:17 Group : ff02::1:ffab:9300 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:24
Field Descriptions:Group: Multicast group address
Last reporter: Address of the last host that reported its membership for this multicast group
Uptime: Length of time since the multicast group was reported
Expires: Remaining time of the multicast group
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see “show ipv6 mld vlan <vid>” on page 2-179.
Minimum Software Version: 15.09.
Comware Related ProVision
display mld group interface vlan-interface <vid> show ipv6 mld vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 173 Sunday, September 9, 2012 6:00 PM
2-174
Display Commandsdisplay mld group interface vlan-interface <vid> verbose
display mld group interface vlan-interface <vid> verbose
Displays information of all MLD groups.
HP Switch# display mld group interface vlan-interface 30 verbose Interface group report informationVlan-Interface30(2075:1:1:30::1): Total 5 MLD Groups reported Group : ff02::2 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:04:00 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::16 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:54 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::1:ff00:0 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:53 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::1:ff00:3 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:58 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a
Comware Related ProVision
display mld group interface vlan-interface <vid> verbose
show ipv6 mld vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 174 Sunday, September 9, 2012 6:00 PM
2-175
Display Commandsdisplay mld group interface vlan-interface <vid> verbose
Last-listener-query-timer-expiry : n/a Group : ff02::1:ffab:9300 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:56 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a
Field Descriptions:
Interface group report information: MLD group information on the interface
Total 5 MLD Groups reported: Five MLD groups were reported.
Group: IPv6 multicast group address
Uptime: Length of time since the IPV6 multicast group was joined
Expires: Remaining time of the IPv6 multicast group, where “off” means that the multicast group never times out
Last reporter: IPv6 address of the host that last reported membership for this group
Last-listener-query-counter: Number of MLD last listener queries sent
Last-listener-query-timer-expiry: Remaining time of the MLD last listener query timer, where “off” means that the timer never times out
Group mode: Multicast source filtering mode:
• include
• exclude
This field is displayed only when the device is running MLDv2.
Version1-host-present-timer-expiry: Remaining time of the MLDv1 host present timer, where “off” means that the timer never times out.
This field is displayed only when the device is running MLDv2.
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see “show ipv6 mld vlan <vid>” on page 2-179.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 175 Sunday, September 9, 2012 6:00 PM
2-176
Display Commandsdisplay mld group port-info vlan <vlan-id> display mld group port-info
display mld group port-info vlan <vlan-id> display mld group port-info
Displays Layer 2 port information of MLD groups, including Layer 2 informa-tion of dynamic and static MLD group entries.
HP Switch# display mld group port-info Total 1 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s). Port flags: D-Dynamic port, S-Static port, C-Copy port Subvlan flags: R-Real VLAN, C-Copy VLAN Vlan(id):100. Total 3 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s). Router port(s):total 0 port(s). IP group(s):the following ip group(s) match to one mac group. IP group address:FF13::1 (::, FF13::1): Host port(s):total 1 port(s). GE2/0/1 (D) MAC group(s): n/a
HP Switch# display mld group port-info vlan 100 Total 1 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s). Port flags: D-Dynamic port, S-Static port, C-Copy port Subvlan flags: R-Real VLAN, C-Copy VLAN Vlan(id):100. Total 3 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s). Router port(s):total 0 port(s). IP group(s):the following ip group(s) match to one mac group. IP group address:FF13::1 (::, FF13::1): Host port(s):total 1 port(s). A1 (D) MAC group(s): n/a
Minimum Software Version: 15.10.
Comware Related ProVision
display mld group port-info vlan <vlan-id>display mld group port-info
No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 176 Sunday, September 9, 2012 6:00 PM
2-177
Display Commandsdisplay mld group verbose
display mld group verbose
Displays information about dynamically added MLD groups on all interfaces.
HP Switch# display mld group verboseTotal 5 MLD Group(s).Interface group report informationVlan-Interface30(2075:1:1:30::1): Total 5 MLD Groups reported Group : ff02::2 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:31 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::16 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:26 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::1:ff00:0 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:24 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::1:ff00:3 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:30 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::1:ffab:9300
Comware Related ProVision
display mld group verbose show ipv6 mld vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 177 Sunday, September 9, 2012 6:00 PM
2-178
Display Commandsdisplay mld group verbose
Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:28 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a
Field Descriptions:
Interface group report information: MLD group information on the interface
Total 1 MLD Groups reported: One MLD group was reported.
Group: IPv6 multicast group address
Uptime: Length of time since the IPV6 multicast group was joined
Expires: Remaining time of the IPv6 multicast group, where “off” means that the multicast group never times out
Last reporter: IPv6 address of the host that last reported membership for this group
Last-listener-query-counter: Number of MLD last listener queries sent
Last-listener-query-timer-expiry: Remaining time of the MLD last listener query timer, where “off” means that the timer never times out
Group mode: Multicast source filtering mode:
• include
• exclude
This field is displayed only when the device is running MLDv2.
Version1-host-present-timer-expiry: Remaining time of the MLDv1 host present timer, where “off” means that the timer never times out.
This field is displayed only when the device is running MLDv2.
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see “show ipv6 mld vlan <vid>” on page 2-179.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 178 Sunday, September 9, 2012 6:00 PM
2-179
Display Commandsdisplay mld group x:x::x:x
display mld group x:x::x:x
Displays information of all MLD groups.
HP Switch# display mld group ff02::2Interface group report information Interface:Vlan30 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:38
Field Descriptions:
Group: Multicast group address
Last reporter: Address of the last host that reported its membership for this multicast group
Uptime: Length of time since the multicast group was reported
Expires: Remaining time of the multicast group
Example of Related ProVision Software Command Output.
There is no equivalent ProVision command.
HP Switch# show ipv6 mld vlan 30
MLD Service Protocol Info
VLAN ID : 30 NAME : VLAN30 MLD Version : 2
MLD Interface State : Non-Querier Querier Address : fe80::3e4a:92ff:feab:9300 Port : A2 Version : 2 Uptime : 5d 18h 38m Expires : 3m 48s Ports with multicast routers : A2
Comware Related ProVision
display mld group x:x::x:x show ipv6 mld vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 179 Sunday, September 9, 2012 6:00 PM
2-180
Display Commandsdisplay mld group x:x::x:x
Active Group Addresses Tracking Vers Mode Uptime Expires ----------------------- ------- ---- ---- -------- -----
ff02::2 Standard 1 EXC 5d 18... 2m 30s ff02::16 Standard 1 EXC 5d 18... 2m 33s ff02::1:ff00:0 Standard 1 EXC 5d 18... 2m 28s ff02::1:ff00:3 Standard 1 EXC 5d 18... 2m 27s ff02::1:ffab:9300 Standard 1 EXC 5d 18... 2m 24s
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 180 Sunday, September 9, 2012 6:00 PM
2-181
Display Commandsdisplay mld group x:x::x:x verbose
display mld group x:x::x:x verbose
Displays information of all MLD groups.
HP Switch# display mld group verbose
Interface group report informationVlan-interface100(FE80::101) Total 1 MLD Groups reported Group: FF03::101 Uptime: 00:01:46 Expires: 00:01:30 Last reporter: FE80::10 Last-listener-query-counter: 0 Last-listener-query-timer-expiry: off Group mode: include Version1-host-present-timer-expiry: off
Field Descriptions:
Interface group report information: MLD group information on the interface
Total 1 MLD Groups reported: One MLD group was reported.
Group: IPv6 multicast group address
Uptime: Length of time since the IPV6 multicast group was joined
Expires: Remaining time of the IPv6 multicast group, where “off” means that the multicast group never times out
Last reporter: IPv6 address of the host that last reported membership for this group
Last-listener-query-counter: Number of MLD last listener queries sent
Last-listener-query-timer-expiry: Remaining time of the MLD last listener query timer, where “off” means that the timer never times out
Group mode: Multicast source filtering mode:
• include
• exclude
Comware Related ProVision
display mld group x:x::x:x verbose show ipv6 mld vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 181 Sunday, September 9, 2012 6:00 PM
2-182
Display Commandsdisplay mld group x:x::x:x verbose
This field is displayed only when the device is running MLDv2.
Version1-host-present-timer-expiry: Remaining time of the MLDv1 host present timer, where “off” means that the timer never times out.
This field is displayed only when the device is running MLDv2.
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see “show ipv6 mld vlan <vid>” on page 2-179.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 182 Sunday, September 9, 2012 6:00 PM
2-183
Display Commandsdisplay mld interface
display mld interface
Displays MLD configuration and operation information on the specified inter-face or all MLD-enabled interfaces.
HP Switch# display mld interfaceInterface informationVlan-Interface30(2075:1:1:30::1):MLD is enabledCurrent MLD version is 2Value of query interval for MLD(in seconds) : 125 Value of other querier present interval for MLD(in seconds) : 255 Value of maximum query response time for MLD(in seconds) : 10 Querier for MLD : fe80::3e4a:92ff:feab:9300 Total 5 MLD Groups reported
Field Descriptions:
Vlan-interface30 (2075:1:1:30::1): Interface and IPv6 link-local address
Current MLD version: MLD version running on the interface
Value of query interval for MLD (in seconds): MLD query interval, in seconds
Value of other querier present interval for MLD (in seconds): MLD other querier present interval, in seconds
Value of maximum query response time for MLD (in seconds): Maximum response delay for general query messages (in seconds)
Querier for MLD: IPv6 link-local address of the MLD querier
Total 5 MLD Groups reported: Total number of MLD groups the interface has dynamically joined
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see “show ipv6 mld vlan <vid>” on page 2-179.
Minimum Software Version: 15.09.
Comware Related ProVision
display mld interface show ipv6 mld vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 183 Sunday, September 9, 2012 6:00 PM
2-184
Display Commandsdisplay mld interface verbose
display mld interface verbose
Displays MLD configuration and operation information on the specified inter-face or all MLD-enabled interfaces.
HP Switch# display mld interface verboseInterface informationVlan-Interface30(2075:1:1:30::1): MLD is enabled Current MLD version is 2 Value of query interval for MLD(in seconds) : 125 Value of other querier present interval for MLD(in seconds) : 255 Value of maximum query response time for MLD(in seconds) : 10 Querier for MLD : fe80::3e4a:92ff:feab:9300 Value of last listener query interval(in seconds) : 1 Value of startup query interval(in seconds) : 31 Value of startup query count : 2 General query timer expiry (hours:minutes:seconds) : 00:03:19 MLD activity : 19861 joins, 0 leaves Multicast ipv6 routing on this interface : n/a Robustness : 2 Require-router-alert : enabled Fast-leave : enabled Ssm-mapping : n/a Startup-query-timer-expiry : off Other-querier-present-timer-expiry : on Proxying interface : n/a
Field Descriptions:
Vlan-Interface30(2075:1:1:30::1): Interface and IPv6 link-local address
Current MLD version: MLD version running on the interface
Value of query interval for MLD (in seconds): MLD query interval, in seconds
Value of other querier present interval for MLD (in seconds): MLD other querier present interval, in seconds
Value of maximum query response time for MLD (in seconds): Maximum response delay for general query messages (in seconds)
Comware Related ProVision
display mld interface verbose show ipv6 mld vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 184 Sunday, September 9, 2012 6:00 PM
2-185
Display Commandsdisplay mld interface verbose
Value of last listener query interval (in seconds): MLD last listener query interval, in seconds
Value of startup query interval(in seconds): MLD startup query interval, in sec-onds
Value of startup query count: Number of MLD general queries sent on startup
General query timer expiry: Remaining time of the MLD general query timer, where “off” means that the timer never times out
Querier for MLD: IPv6 link-local address of the MLD querier
MLD activity: MLD activity statistics (number of join and done messages)
Robustness: MLD querier’s robustness variable
Require-router-alert: Dropping MLD messages without Router-Alert (enabled/disabled)
Fast-leave: MLD fast leave processing status (enabled/disabled)
Ssm-mapping: MLD SSM mapping status (enabled/disabled)
Startup-query-timer-expiry: Remaining time of MLD startup query timer, where “off” means that the timer never times out
Other-querier-present-timer-expiry: Remaining time of MLD other querier pres-ent timer, where “off” means that the timer never times out
Proxying interface: The MLD proxy interface, where “none” means that no proxy interface exists
MLD proxy is enabled: MLD proxying is enabled
Version1-querier-present-timer-expiry: Remaining time of the MLDv1 querier present timer, where “off” means that the timer never times out
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see “show ipv6 mld vlan <vid>” on page 2-179.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 185 Sunday, September 9, 2012 6:00 PM
2-186
Display Commandsdisplay mld interface vlan-interface <vid>
display mld interface vlan-interface <vid>
Displays MLD configuration and operation information on the specified inter-face or all MLD-enabled interfaces.
HP Switch# display mld interface vlan-interface 30 Vlan-Interface30(2075:1:1:30::1): MLD is enabled Current MLD version is 2 Value of query interval for MLD(in seconds) : 125 Value of other querier present interval for MLD(in seconds) : 255 Value of maximum query response time for MLD(in seconds) : 10 Querier for MLD : fe80::3e4a:92ff:feab:9300 Total 5 MLD Groups reported
Field Descriptions:
Vlan-Interface30(2075:1:1:30::1): Interface and IPv6 link-local address
Current MLD version: MLD version running on the interface
Value of query interval for MLD (in seconds): MLD query interval, in seconds
Value of other querier present interval for MLD (in seconds): MLD other querier present interval, in seconds
Value of maximum query response time for MLD (in seconds): Maximum response delay for general query messages (in seconds)
Querier for MLD: IPv6 link-local address of the MLD querier
Total 5 MLD Groups reported: Total number of MLD groups the interface has dynamically joined
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see “show ipv6 mld vlan <vid>” on page 2-179.
Minimum Software Version: 15.09.
Comware Related ProVision
display mld interface vlan-interface <vlan-id> show ipv6 mld vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 186 Sunday, September 9, 2012 6:00 PM
2-187
Display Commandsdisplay mld interface vlan-interface <vid> verbose
display mld interface vlan-interface <vid> verbose
Displays MLD configuration and operation information on the specified inter-face or all MLD-enabled interfaces.
HP Switch# display mld interface vlan-interface 30 verboseVlan-Interface30(2075:1:1:30::1): MLD is enabled Current MLD version is 2 Value of query interval for MLD(in seconds) : 125 Value of other querier present interval for MLD(in seconds) : 255 Value of maximum query response time for MLD(in seconds) : 10 Querier for MLD : fe80::3e4a:92ff:feab:9300 Value of last listener query interval(in seconds) : 1 Value of startup query interval(in seconds) : 31 Value of startup query count : 2 General query timer expiry (hours:minutes:seconds) : 00:02:38 MLD activity : 19866 joins, 0 leaves Multicast ipv6 routing on this interface : n/a Robustness : 2 Require-router-alert : enabled Fast-leave : enabled Ssm-mapping : n/a Startup-query-timer-expiry : off Other-querier-present-timer-expiry : on Proxying interface : n/a Total 5 MLD Groups reported
Field Descriptions:
Vlan-interface100(FE80::200:AFF:FE01:101): Interface and IPv6 link-local address
Current MLD version: MLD version running on the interface
Value of query interval for MLD (in seconds): MLD query interval, in seconds
Value of other querier present interval for MLD (in seconds): MLD other querier present interval, in seconds
Comware Related ProVision
display mld interface vlan-interface <vid> verbose
show ipv6 mld vlan <vid>
Common-CLI-Phase-3-Sept-2012.book Page 187 Sunday, September 9, 2012 6:00 PM
2-188
Display Commandsdisplay mld interface vlan-interface <vid> verbose
Value of maximum query response time for MLD (in seconds): Maximum response delay for general query messages (in seconds)
Value of last listener query interval (in seconds): MLD last listener query interval, in seconds
Value of startup query interval(in seconds): MLD startup query interval, in sec-onds
Value of startup query count: Number of MLD general queries sent on startup
General query timer expiry: Remaining time of the MLD general query timer, where “off” means that the timer never times out
Querier for MLD: IPv6 link-local address of the MLD querier
MLD activity: MLD activity statistics (number of join and done messages)
Robustness: MLD querier’s robustness variable
Require-router-alert: Dropping MLD messages without Router-Alert (enabled/disabled)
Fast-leave: MLD fast leave processing status (enabled/disabled)
Ssm-mapping: MLD SSM mapping status (enabled/disabled)
Startup-query-timer-expiry: Remaining time of MLD startup query timer, where “off” means that the timer never times out
Other-querier-present-timer-expiry: Remaining time of MLD other querier pres-ent timer, where “off” means that the timer never times out
Proxying interface: The MLD proxy interface, where “none” means that no proxy interface exists
Total 1 MLD Group reported: Total number of MLD groups the interface has dynamically joined
MLD proxy is enabled: MLD proxying is enabled
Version1-querier-present-timer-expiry: Remaining time of the MLDv1 querier present timer, where “off” means that the timer never times out
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see “show ipv6 mld vlan <vid>” on page 2-179.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 188 Sunday, September 9, 2012 6:00 PM
2-189
Display Commandsdisplay mld routing-table
display mld routing-table
Displays information about the MLD routing table.
HP Switch# display mld routing-table Routing table Total 2 entries 00001. (*, 2ffd::1) List of 2 downstream interfaces Vlan-interface100 (fe80::3ee5:a6ff:fe18:1142), Protocol: MLD Vlan-interface200 (fe80::3ee5:a6ff:fe18:1143), Protocol: MLD 00002. (2ffc::9, 2ffd::1) List of 2 downstream interfaces in exclude mode Vlan-interface100 (fe80::3ee5:a6ff:fe18:1142), Protocol: MLD Vlan-interface200 (fe80::3ee5:a6ff:fe18:1143), Protocol: MLD
Minimum Software Version: 15.10.
Comware Related ProVision
display mld routing-table No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 189 Sunday, September 9, 2012 6:00 PM
2-190
Display Commandsdisplay monitor-link group [group-number | all],
display monitor-link group [group-number | all],
Displays information about the specified or all monitor link groups.
Field Descriptions
Monitor link group 1 information: Information about monitor link group 1.
Group status: Monitor link group state, which can be up or down or none.
Last-up-time: Last time when the monitor link group was up.
Last-down-time: Last time when the monitor link group was down.
Member: Member ports of the monitor link group.
Role: Port role, which can be uplink port or downlink port.
Status: Member link state, which can be up or down.
Operating Notes
In ProVision, groupid ranges from 1 to 64 whereas in H3C switches, groupid ranges from 1 to 24. For more information about link groups, see the “Port Status and Configuration” chapter in the latest Management and Configura-
tion Guide for your switch.
Comware Related ProVision
display monitor-link group<group-number | all]
show uplink-failure-detection
HP Switch# display monitor-link group 2 Monitor link group 2 information: Group status : NONE Last-up-time : n/a Last-down-time : n/a Member Role Status ------------------------------------------- 3 UPLINK DOWN 4 DOWNLINK DOWN
Common-CLI-Phase-3-Sept-2012.book Page 190 Sunday, September 9, 2012 6:00 PM
2-191
Display Commandsdisplay monitor-link group [group-number | all],
Example of Related ProVision Software Command Output.
display monitor-link group Field Mappings.
Minimum Software Version: 15.09.
HP Switch(config)# show uplink-failure-detection
Uplink Failure Detection Information UFD Enabled : Yes
TRACK ID | Monitored Links Links to Disable LtM State LtD State -------- + --------------- ---------------- --------- --------------- 3 5,6 3 Up Up 4 13 4-5 Down Auto-Disabled
Comware ProVision Software
Monitor link group Track ID
Group status UFD State
Last-up-time n/a
Last-down-time n/a
Member Monitored Links/Links to Disable
Role n/a
Status LtMState/LtD State
Common-CLI-Phase-3-Sept-2012.book Page 191 Sunday, September 9, 2012 6:00 PM
2-192
Display Commandsdisplay multicast forwarding-table
display multicast forwarding-table
Displays multicast forwarding table information. If neither all-instance nor vpn-instance is specified, this command displays the information on the public network. Multicast forwarding tables guide multicast forwarding. You can view the forwarding state of multicast traffic by checking the multicast forwarding table.
HP Switch# display multicast forwarding-table
Multicast Forwarding Table of VPN-Instance: n/a
Total 1 entry
Total 1 entry matched
00001. (30.30.30.1, 239.1.1.1) MID: n/a, Flags: 0x2:0 Uptime: 00:00:21, Timeout in: 00:00:02 Incoming interface: Vlan-interface10 List of 1 outgoing interfaces: 1: Vlan-interface20 Matched 2 packets(bytes n/a), Wrong If 0 packets Forwarded 0 packets(0 bytes)
Minimum Software Version: 15.10.
Comware Related ProVision
display multicast forwarding-table No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 192 Sunday, September 9, 2012 6:00 PM
2-193
Display Commandsdisplay multicast routing-table
display multicast routing-table
Displays multicast routing table information. Multicast routing tables are the basis of multicast forwarding. You can view the establishment state of an (S, G) entry by checking the multicast routing table.
HP Switch# display multicast routing-tableMulticast routing table of VPN-Instance: public netTotal 1 entry,1 matched
00001. (20.20.20.2, 239.1.1.1) Uptime: 00:00:20 Upstream Interface: 10 List of 1 downstream interfaces 1: Vlan-interface30
HP Switch# display multicast routing-table 20.20.20.1 239.1.1.1Multicast routing table of VPN-Instance: public netTotal 1 entry,1 matched
00001. (20.20.20.2, 239.1.1.1) Uptime: 00:00:20 Upstream Interface: 10 List of 1 downstream interfaces 1: Vlan-interface30
HP Switch# display multicast routing-table 20.20.20.1 239.1.1.1 incoming-interface Vlan-interface 20Multicast routing table of VPN-Instance: public netTotal 1 entry,1 matched
00001. (20.20.20.2, 239.1.1.1) Uptime: 00:00:20 Upstream Interface: 10 List of 1 downstream interfaces 1: Vlan-interface30
HP Switch# display multicast routing-table 20.20.20.1 239.1.1.1 incoming-interface Vlan-interface 20 outgoing-interface Vlan-interface 30Multicast routing table of VPN-Instance: public netTotal 1 entry,1 matched
00001. (20.20.20.2, 239.1.1.1) Uptime: 00:00:20 Upstream Interface: 10
Comware Related ProVision
display multicast routing-table show ip mroute
Common-CLI-Phase-3-Sept-2012.book Page 193 Sunday, September 9, 2012 6:00 PM
2-194
Display Commandsdisplay multicast routing-table
List of 1 downstream interfaces 1: Vlan-interface30
Example of Related ProVision Software Command Output.
HP Switch# show ip mrouteIP Multicast Route EntriesTotal number of entries : 2Group Address Source Address Neighbor VLAN--------------- --------------- ----------- ----239.255.255.1 10.27.30.2 10.29.30.1 29239.255.255.5 10.27.30.2 10.29.30.1 29
Operating Notes
For more information, refer to the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 194 Sunday, September 9, 2012 6:00 PM
2-195
Display Commandsdisplay multicast routing-table static
display multicast routing-table static
Displays the information about multicast static routes.
Field Descriptions
Multicast Routing Table of VPN-Instance: public net: Multicast routing table for the public network
Mroute: Multicast route source address and its mask length
Interface: Outgoing interface to the multicast source
RPF Neighbor: IP address of the RPF neighbor through which the multicast source is reachable
Route-policy: Routing policy. The multicast source address of the route should match the routing policy.
Preference: Route preference
Order: Sequence number of the route
Running Configuration: Command line that configures the multicast static route
Comware Related ProVision
display multicast routing-table static show ip pim rpf-override
HP Switch# display multicast routing-table staticMulticast Routing Table of VPN-Instance: n/aRoutes : n/a Mroute 10.10.0.0/16 Interface = n/a RPF Neighbor = 2.2.2.2 Matched routing protocol = <none>, Route-policy = <none> Preference = n/a, Order = n/a Running Configuration = rpf-override 10.10.10.10/32 10.10.10.1
Common-CLI-Phase-3-Sept-2012.book Page 195 Sunday, September 9, 2012 6:00 PM
2-196
Display Commandsdisplay multicast routing-table static
Operating Notes
ProVision switches use a different command to define the static multicast routes, The corresponding config command is displayed in the command. For more information on multicast static routes, see the “PIM-SM (Sparse Mode)” or the “PIM-DM (Dense Mode) chapters in the latest Multicast and Routing
Guide for your switch.
Example of Related ProVision Software Command Output.
display multicast routing-table static Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
Multicast Routing Table of VPN-Instance: public net
n/a
Mroute n/a
Interface n/a
RPF Neighbor RPF IP Address
Route-policy n/a
Preference n/a
Order n/a
Running Configuration n/a
HP Switch(config)# show ip pim rpf-override
Static RPF Override
Multicast Source RPF IP Address ------------------- --------------- 10.1.1.1/32 11.2.2.1 13.1.1.1/32 12.1.1.1
Common-CLI-Phase-3-Sept-2012.book Page 196 Sunday, September 9, 2012 6:00 PM
2-197
Display Commandsdisplay multicast rpf-info
display multicast rpf-info
Displays rpf override information of a multicast source.
HP Switch# display multicast rpf-info 10.10.10.10 RPF information about source 10.10.10.10: VPN instance: n/a RPF interface: Vlan-Interface 10 Referenced route/mask: 40.40.40.40/32 Referenced route type: n/a Route selection rule: n/a Load splitting rule: n/a
Minimum Software Version: 15.10.
Comware Related ProVision
display multicast rpf-info No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 197 Sunday, September 9, 2012 6:00 PM
2-198
Display Commandsdisplay ospf cumulative
display ospf cumulative
Displays OSPF statistics information.
Field Descriptions
IO Statistics: Statistics about input/output packets and LSAs.
Type: OSPF packet type.
Input: Packets received.
Output: Packets sent.
Hello: Hello packet.
Comware Related ProVision
display ospf cumulative show ip ospf statistics
HP Switch# display ospf cumulative
OSPF Process 1 with Router ID : 2.2.2.2 Cumulations
IO Statistics Type Input Output Hello 2 2 DB Description 0 2 Link-State Req 0 0 Link-State Update 0 0 Link-State Ack 0 0
LSAs originated by this router Router: n/a Network: n/a Sum-Net: n/a Sum-Asbr: n/a External: n/a NSSA: n/a Opq-Link: n/a Opq-Area: n/a Opq-As: n/a
LSAs Originated: n/a LSAs Received: n/a
Routing Table: Intra Area: n/a Inter Area: n/a ASE/NSSA: n/a
Common-CLI-Phase-3-Sept-2012.book Page 198 Sunday, September 9, 2012 6:00 PM
2-199
Display Commandsdisplay ospf cumulative
DB Description: Database Description packet
Link-State Req: Link-State Request packet.
Link-State Update: Link-State Update packet.
Link-State-Ack: Link-State Acknowledge packet.
LSAs originated by this router: LSAs originated by this router.
Router: Number of Type-1 LSAs originated.
Network: Number of Type-2 LSAs originated.
Sum-Net: Number of Type-3 LSAs originated.
Sum-Asbr: Number of Type-4 LSAs originated.
External: Number of Type-5 LSAs originated.
NSSA: Number of Type-7 LSAs originated.
Opq-Link: Number of Type-9 LSAs originated.
Opq-Area: Number of Type104 LSAs originated.
Opq-As: Number of Type-11 LSAs originated.
LSA originated: Number of LSAs originated.
LSA Received: Number of LSAs received.
Routing Table: Routing table information.
Intra Area: Intra-area route number.
Inter Area: Inter-area route number.
ASE: ASE route number.
Operating Notes
For more on switch OSPF operation, refer to the “IP Routing” chapter in the latest Multicast and Routing Guide for your switch.
Common-CLI-Phase-3-Sept-2012.book Page 199 Sunday, September 9, 2012 6:00 PM
2-200
Display Commandsdisplay ospf cumulative
Example of Related ProVision Software Command Output.
display ospf cumulative Field Mappings.
Minimum Software Version: 15.09.
HP Switch(ospf)# show ip ospf statistics vlan 1
OSPF statistics for VLAN 1
OSPF Interface Status for 10.0.0.2
Tx Hello Packet Count : 16 Rx Hello Packet Count : 16 Tx DD Packet Count : 2 Rx DD Packet Count : 4 Tx LSR Packet Count : 1 Rx LSR Packet Count : 1 Tx LSU Packet Count : 5 Rx LSU Packet Count : 2 Tx LSA Packet Count : 2 Rx LSA Packet Count : 3
OSPF Errors: 26
Comware ProVision Software
Hello TX/RX Hello Packet Count
DB Description n/a
Link-state Req n/a
Link-State Update n/a
Link-State Ack n/a
LSA originated n/a
LSA received n/a
Routing Table fields n/a
Common-CLI-Phase-3-Sept-2012.book Page 200 Sunday, September 9, 2012 6:00 PM
2-201
Display Commandsdisplay ospf interface
display ospf interface
Displays OSPF interface information for all OSPF processes.
Field Descriptions
Area: Area ID of the interface.
IP Address: Interface IP address.
Type: Interface network type (PTP, PTMP, Broadcast, or NBMA.
State: Interface state:
• Down: No protocol traffic will be sent or received on the interface.
• Waiting: The interface starts sending and receiving Hello packets and the router is trying to determine the identity of the backup designated router for the network.
• p-2-p: The interface will send Hello packets at the interval of HelloIn-terval, and try to establish an adjacency with the neighbor.
• DR: The router itself is the designated router on the attached network.
• BDR: The router itself is the backup designated router on the attached network.
Comware Related ProVision
display ospf interface show ip ospf interface
HP Switch(config)# display ospf interface
OSPF Process 1 with Router ID : 192.168.1.1 Area : 0.0.0.0
IP Address Type State Cost Pri DR BDR --------------- --------- ------- ----- --- --------------- --------------- 192.168.1.1 PTP P-2-P 1562 1 0.0.0.0 0.0.0.0
Area : 0.0.0.1
IP Address Type State Cost Pri DR BDR --------------- --------- ------- ----- --- --------------- --------------- 172.16.0.1 BROADCAST DR 1562 1 172.16.0.1 0.0.0.0
Common-CLI-Phase-3-Sept-2012.book Page 201 Sunday, September 9, 2012 6:00 PM
2-202
Display Commandsdisplay ospf interface
• DROther: The interface is on a network on which another router is the designated router.
Cost: Interface cost.
Pri: Router priority.
DR: The DR on the interface’s network segment.
BDR: The BDR on the interface’s network segment.
Operating Notes
To enable OSPF operation in ProVision software, use the following command in the global configuration context:
router ospf enable
For more on configuring OSPF, including additional OSPF configuration commands, see the “Configuring OSPF” chapter in the latest Multicast and
Routing Guide for your switch.
Example of Related ProVision Software Command Output.
OSPF Interface Field Mappings.
HP Switch(config)# show ip ospf interface
OSPF Interface Status
IP Address Status Area ID State Auth-type Cost Pri Passive --------------- -------- --------------- ------- --------- ----- --- ------- 172.16.0.1 enabled backbone DR none 1562 1 no
Comware ProVision Software
Area Area ID
IP Address IP Address
n/a Status
Type n/a
State State
n/a Auth-Type
Cost Cost
Common-CLI-Phase-3-Sept-2012.book Page 202 Sunday, September 9, 2012 6:00 PM
2-203
Display Commandsdisplay ospf interface
Minimum Software Version: 15.08.
PRI PRI
n/a Passive
DR n/a
BDR n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 203 Sunday, September 9, 2012 6:00 PM
2-204
Display Commandsdisplay ospf lsdb
display ospf lsdb
Displays OSPF link state database information.
Field Descriptions
Area: LSDB information of the area
Type: LSA type
LinkState ID: Linkstate ID
AdvRouter: The router that advertised the LSA
Age: Age of the LSA
Len: Length of the LSA
Comware Related ProVision
display ospf lsdb show ip ospf link-stateshow ip ospf external-link-state
HP Switch# display ospf lsdb
OSPF Process 1 with Router ID 7.7.7.7 Link State Database
Area: 0.0.0.0 Type LinkState ID AdvRouter Age Len Sequence Metric Router 11.0.9.2 11.0.9.2 930 n/a 80000005 n/a Router 11.0.9.1 11.0.9.1 456 n/a 80000004 n/a Network 11.0.9.2 11.0.9.2 930 n/a 80000002 n/a Sum-Net 1.2.4.0 11.0.9.1 16 n/a 80000001 n/a Area: 0.0.0.1 Type LinkState ID AdvRouter Age Len Sequence Metric Router 11.0.9.1 11.0.9.1 9 n/a 80000003 n/a Router 100.0.9.4 100.0.9.4 10 n/a 80000004 n/a Network 1.2.4.6 100.0.9.4 5 n/a 80000002 n/a Sum-Net 11.0.9.0 11.0.9.1 16 n/a 80000001 n/a
AS External Database Type LinkState ID AdvRouter Age Len Sequence Metric External 192.168.1.0 3.3.3.3 406 n/a 80000006 n/a[bot-ospf-1-area-0.0.0.1]
Common-CLI-Phase-3-Sept-2012.book Page 204 Sunday, September 9, 2012 6:00 PM
2-205
Display Commandsdisplay ospf lsdb
Sequence: Sequence number of the LSA
Metric: Cost of the LSA
Operating Notes
For more on switch OSPF operation, refer to the “IP Routing” chapter in the latest Multicast and Routing Guide for your switch.
Example of Related ProVision Software Command Output.
display ospf lsdb Field Mappings.
HP Switch# show ip ospf link-state
OSPF Link State Database for Area 0.0.0.0 Advertising LSA Type Link State ID Router ID Age Sequence # Checksum ---------- --------------- --------------- ---- ----------- ---------- Router 10.0.8.32 10.0.8.32 65 0x80000281 0x0000a7b6 Router 10.0.8.33 10.0.8.33 1638 0x80000005 0x0000a7c8 Network 10.3.2.37 10.0.8.37 1695 0x80000006 0x00000443 Summary 10.3.16.0 10.0.8.33 1638 0x80000007 0x0000c242 Summary 10.3.16.0 10.0.8.35 1316 0x80000008 0x0000aa58 Summary 10.3.17.0 10.0.8.33 1638 0x8000027b 0x0000becf Summary 10.3.17.0 10.0.8.35 1316 0x80000008 0x0000a957 AsbSummary 10.0.8.36 10.0.8.33 1412 0x80000002 0x00002cba OSPF Link State Database for Area 10.3.16.0 Advertising LSA Type Link State ID Router ID Age Sequence # Checksum ---------- --------------- --------------- ---- ----------- ---------- Router 10.0.8.33 10.0.8.33 1727 0x8000027e 0x0000d53c Router 10.0.8.34 10.0.8.34 1420 0x80000283 0x0000de4f Network 10.3.16.34 10.0.8.34 1735 0x80000005 0x00001465
Comware ProVision Software
Area Area
Type LSA Type
Common-CLI-Phase-3-Sept-2012.book Page 205 Sunday, September 9, 2012 6:00 PM
2-206
Display Commandsdisplay ospf lsdb
Minimum Software Version: 15.09.
LinkState ID Link State ID
AdvRouter Router ID
Age Age
Len n/a
Sequence Sequence
Metric n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 206 Sunday, September 9, 2012 6:00 PM
2-207
Display Commandsdisplay ospf peer
display ospf peer
Displays information about OSPF neighbors.
Field Descriptions
Area: Neighbor area.
Router ID: Neighbor router ID
Address: Neighbor interface address.
Pri: Neighboring router priority.
Dead-Time: Dead interval remained.
Interface: Interface connected to the neighbor.
State: Neighbor state: Down, Init, Attempt, 2-Way, Exstart, Exchange, DR/BDR state, Loading or Full.
Operating Notes
For more on switch OSPF operation, refer to the “IP Routing” chapter in the latest Multicast and Routing Guide for your switch.
Comware Related ProVision
display ospf peer show ip ospf neighbor
HP Switch# display ospf peer
OSPF Process 1 with Router ID 1.1.1.1 Neighbor Brief Information Area: 0.0.0.0
Router ID Address Pri Dead-Time Interface State 1.1.1.2 1.1.1.2 1 40 Vlan11 Full/DR
Common-CLI-Phase-3-Sept-2012.book Page 207 Sunday, September 9, 2012 6:00 PM
2-208
Display Commandsdisplay ospf peer
Example of Related ProVision Software Command Output.
display ospf peer Field Mappings.
Minimum Software Version: 15.09.
HP Switch(config)# show ip ospf neighbor
OSPF Neighbor Information Rxmt Helper Router ID Pri IP Address NbIfState State QLen Events Status --------------- --- -------------- --------- --------- ----- ------ ------ 10.0.8.34 1 10.3.18.34 DR FULL 0 6 none 10.3.53.38 1 10.3.53.38 DR FULL 0 6 none
Comware ProVision Software
Area n/a
Router ID Router ID
Address IP Address
Pri Pri
Dead-Time Dead Timer Expires
Interface n/a
State NbIfState/State
Common-CLI-Phase-3-Sept-2012.book Page 208 Sunday, September 9, 2012 6:00 PM
2-209
Display Commandsdisplay ospf routing
display ospf routing
Displays OSPF routing information for all OSPF processes.
Field Descriptions
Destination: Destination network.
Cost: Cost to destination.
Type: Route type (intra-area, transit, stub, inter-area, type 1 external, type 2 external.
NextHop: Next hop address.
AdvRouter: Advertising router.
Area: Area ID.
Total Nets: Total networks.
Intra Area: Total intra-area routes.
Inter Area: Total inter-area routes.
ASE: Total ASE routes.
NSSA: Total NSSA routes.
Comware Related ProVision
display ospf routing show ip ospf
HP Switch(config)# display ospf routing
OSPF Process 1 with Router ID 192.168.1.2 Routing Tables Routing for Network Destination Cost Type NextHop AdvRouter Area 192.168.1.0/24 1562 Stub 192.168.1.2 192.168.1.2 0.0.0.0 172.16.0.0/16 1563 Inter 192.168.1.1 192.168.1.1 0.0.0.0
Total Nets: 2
Intra Area: 1 Inter Area: 1 ASE: 0 NSSA: 0
Common-CLI-Phase-3-Sept-2012.book Page 209 Sunday, September 9, 2012 6:00 PM
2-210
Display Commandsdisplay ospf routing
Operating Notes
To enable OSPF operation in ProVision software, use the following command in the global configuration context:
router ospf enable
For more on configuring OSPF, including additional OSPF configuration commands, see the “Configuring OSPF” chapter in the latest Multicast and
Routing Guide for your switch.
Minimum Software Version: 15.08.
Common-CLI-Phase-3-Sept-2012.book Page 210 Sunday, September 9, 2012 6:00 PM
2-211
Display Commandsdisplay ospf vlink
display ospf vlink
Displays OSPF virtual link information.
HP Switch# display ospf vlink OSPF Process 1 with Router ID 3.3.3.3 Virtual Links Virtual-link Neighbor-ID -> 2.2.2.2, Neighbor-State: Full Interface: 10.1.2.1 (Vlan-interface11) Cost: 1562 State: P-2-P Type: Virtual Transit Area: 0.0.0.1 Timers: Hello 10 , Dead 40 , Retransmit 5 , Transmit Delay 1
Field Descriptions
Virtual-link Neighbor-ID: ID of the neighbor connected to the router via the virtual link.
Neighbor-State: Neighbor’s operating state (Down, Init, 2-Way, ExStart, Exchange, Loading Full).
Interface: Local interface’s IP address and name of the virtual link.
Cost: Interface route cost.
State: Interface state.
Type: Link type (virtual link).
Transit Area: Transit area ID.
Timers: Values of the hello, dead, poll (NBMA), retransmit, and interface transmission delay timers.
Operating Notes
To enable OSPF operation in ProVision software, use the following command in the global configuration context:
router ospf enable
Comware Related ProVision Software
display ospf vlink show ip ospf virtual-link
Common-CLI-Phase-3-Sept-2012.book Page 211 Sunday, September 9, 2012 6:00 PM
2-212
Display Commandsdisplay ospf vlink
For more on configuring OSPF, including virtual links and other OSPF opera-tion, see the “Configuring OSPF” chapter in the latest Multicast and Routing
Guide for your switch.
Example of Related ProVision Software Command Output.
ospf vlink Field Mappings.
Minimum Software Version: 15.08.
HP Switch(config)# show ip ospf virtual-link
OSPF Virtual Interface Status
Transit AreaID Neighbor Router Authentication Interface State --------------- --------------- --------------- --------------- 0.0.0.1 2.2.2.2 none P2P
Comware ProVision Software
Virtual-link Neighbor ID Neighbor Router
Neighbor-State Interface State
Interface n/a
Cost n/a
State n/a
Transit Area Transit AreaID
Timers n/a
n/a Authentication
Common-CLI-Phase-3-Sept-2012.book Page 212 Sunday, September 9, 2012 6:00 PM
2-213
Display Commandsdisplay ospfv3
display ospfv3
Displays brief information about OSPFv3.
HP Switch# display ospfv3 Routing Process "OSPFv3 (1)" with ID 3.3.3.3 Graceful restart restarter disabled Graceful restart helper enabled Graceful restart helper strict-lsa-checking disabled Graceful restart interval n/a SPF schedule delay 5 secs, Hold time between SPFs 10 secs Minimum LSA interval n/a, Minimum LSA arrival n/a Number of external LSA 1. These external LSAs' checksum Sum 0x7741 Number of AS-Scoped Unknown LSA 0 Number of LSA originated 4 Number of LSA received 0 Number of areas in this router is 2 Area BACKBONE(0) Number of interfaces in this area is 1 SPF algorithm executed 0 times Number of LSA 0. These LSAs' checksum Sum 0x0000 Number of Unknown LSA 0 Area 0.0.0.1 Number of interfaces in this area is 1 SPF algorithm executed 9 times Number of LSA 2. These LSAs' checksum Sum 0x1A56A Number of Unknown LSA 0
Example of Related ProVision Software Command Output.
HP Switch# show ipv6 ospf3 generalOSPFv3 General StatusOSPFv3 protocol :enabledRouter ID :10.10.10.80...Nonstop forwarding : EnabledGraceful Restart Interval : 500Graceful Restart Helper Mode : Enabled...
Comware Related ProVision
display ospfv3 show ipv6 ospf3
Common-CLI-Phase-3-Sept-2012.book Page 213 Sunday, September 9, 2012 6:00 PM
2-214
Display Commandsdisplay ospfv3
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 214 Sunday, September 9, 2012 6:00 PM
2-215
Display Commandsdisplay ospfv3 area area-id peer interface interface-type interface number
display ospfv3 area area-id peer interface interface-type interface number
Displays OSPFv3 neighbor information.
Field Descriptions
Neighbor ID: Router ID of a neighbor
Pri: Priority of neighbor router
State: Neighbor state
Dead Time: Dead time remained
Interface: Interface connected to the neighbor
Instance ID: Instance ID
Operating Notes
For more on switch OSPFv3 operation, refer to the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display ospfv3 area area-id peer interface interface-type interface number
No equivalent ProVision software command
HP Switch# display ospfv3 area 0 peer Vlan-interface 1 OSPFv3 (Process 1)
OSPFv3 Area (0.0.0.0)
Neighbor ID Pri State Dead Time Interface Instance ID1.1.1.1 1 Full 00:00:35 Vlan1 0
Common-CLI-Phase-3-Sept-2012.book Page 215 Sunday, September 9, 2012 6:00 PM
2-216
Display Commandsdisplay ospfv3 area area-id peer peer-router-id
display ospfv3 area area-id peer peer-router-id
Displays OSPFv3 neighbor information for the specified area.
Field Descriptions
Neighbor: Neighbor ID.
Interface Address: Interface Address.
In the area: The area address.
Vlan-interface: Vlan-interface <vid> belongs to area <area>.
DR/BDR: Router Id of the Designated Router and the Backup Designated Router.
Options: Displays the capabilities.
Dead timer: Indicates when the dead timer is due.
Neighbor up: Neighbor has been up for the indicated time.
Database Summary List: Number of LSAs sent in the DD packet.
Link State Request List: Number of LSAs in the link state request list.
Comware Related ProVision
display ospfv3 area area-id peer peer-router-id
show ipv6 ospf3 neighbor <ip-addr> detail
HP Switch(config)# display ospfv3 area 0 peer 1.1.1.1 OSPFv3 Process (1) Neighbor 1.1.1.1 is Full, interface address FE80::21B:3FFF:FEF7:DEC0 In the area 0.0.0.0 via interface Vlan-interface1 DR is 2.2.2.2 BDR is 1.1.1.1 Options is 0x000013 (-|R|-|-|E|V6) Dead timer due in 00:00:35 Neighbor is up for 00:03:51 Database Summary List 0 Link State Request List 0 Link State Retransmission List 0 Graceful restart state: Normal
Common-CLI-Phase-3-Sept-2012.book Page 216 Sunday, September 9, 2012 6:00 PM
2-217
Display Commandsdisplay ospfv3 area area-id peer peer-router-id
Link State Retransmission List: Number of LSAs in the link state retransmission list.
Graceful restart state: Graceful restart status can be:
• Normal: Normal status
• Helper: The device is a Graceful Restart Helper of the neighbor.
Operating Notes
For more on switch OSPFv3 operation, refer to the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
display ospfv3 area area-id peer peer-id Field Mappings.
HP Switch(ospf3)# show ipv6 ospf3 neighbor 15.1.0.1 detail
OSPFv3 Neighbor Information for neighbor 15.1.0.1
IPv6 Address : fe80::55:1 Router ID : 15.1.0.1 State : FULL Interface : vlan-55 Designated Router : 15.1.0.1 Area : 0.0.0.1 Backup Designated Router : 15.1.0.4 Priority : 1 Retransmit Queue Length : 0 Options : 19 Neighbor Uptime : 1days Events : 0 Dead Timer Expires : 33 sec
Comware ProVision Software
Neighbor Neighbor
Interface Address IPv6 Address
In the area Area ID
Vlan-interface Interface
DR/BDR Designated Router/Backup Designated Router
Options Options
Dead timer Dead Timer expires
Neighbor up Neighbor Uptime
Database Summary List n/a
Common-CLI-Phase-3-Sept-2012.book Page 217 Sunday, September 9, 2012 6:00 PM
2-218
Display Commandsdisplay ospfv3 area area-id peer peer-router-id
Minimum Software Version: 15.09.
Link State Request n/a
Link State Retransmission List
Retransmit Queue Length
Graceful Restart n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 218 Sunday, September 9, 2012 6:00 PM
2-219
Display Commandsdisplay ospfv3 area area-id peer verbose
display ospfv3 area area-id peer verbose
Displays detailed information about OSPFv3 neighbors for a specified area.
Field Descriptions
Neighbor: Neighbor ID.
Interface Address: Interface Address.
In the area: The area address.
Vlan-interface: Vlan-interface <vid> belongs to area <area>.
DR/BDR: Router Id of the Designated Router and Backup Designated Router.
Options: Displays the capabilities.
Dead timer: Indicates when the dead timer is due.
Neighbor up: Neighbor has been up for the indicated time.
Database Summary List: Number of LSAs sent in the DD packet.
Link State Request List: Number of LSAs in the link state request list.
Link State Retransmission List: Number of LSAs in the link state retransmission list.
Comware Related ProVision
display ospfv3 area area-id peer verbose No equivalent ProVision software command
HP Switch(config)# display ospfv3 area 1 peer verbose
Neighbor 3.3.3.3 is Full, interface address FE80::221:F7FF:FE1B:EC80 In the area 0.0.0.1 via interface Vlan-interface2 DR is 3.3.3.3 BDR is 2.2.2.2 Options is 0x000013 (-|R|-|-|E|V6) Dead timer due in 00:00:34 Neighbor is up for 00:01:44 Database Summary List 0 Link State Request List 0 Link State Retransmission List 0 Graceful restart state: Normal
Common-CLI-Phase-3-Sept-2012.book Page 219 Sunday, September 9, 2012 6:00 PM
2-220
Display Commandsdisplay ospfv3 area area-id peer verbose
Graceful restart state: Graceful restart status can be:
• Normal: Normal status
• Helper: The device is a Graceful Restart Helper of the neighbor.
Operating Notes
For more on switch OSPFv3 operation, refer to the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 220 Sunday, September 9, 2012 6:00 PM
2-221
Display Commandsdisplay ospfv3 interface
display ospfv3 interface
Displays OSPF interface information for all OSPF processes.
N o t e Only one process is supported, so the process number is always 1.
Field Descriptions
Interface ID: Interface ID
IPv6 Prefixes: IPv6 Prefix
OSPF Process: OSPF process
Area: Area ID of the interface.
Instance ID: Instance ID
Router ID: Router ID
Network Type: Network type of the interface (PTP, PTMP, Broadcast, or NBMA).
Comware Related ProVision
display ospfv3 interface show ipv6 ospf3 interface
HP Switch(config)# display ospf3 interface Vlan-interface4 is down, line protocol is up Interface ID vlan-4 IPv6 Prefixes 1234::2/96 (Link-Local Address): OSPFv3 Process (1), Area 0.0.0.4 Instance ID 0 Router ID: 0.0.0.40 Network Type: BROADCAST, Cost: 1 Transmit Delay is 1 sec, State: DR Priority: 1 Designated Router (ID) 2001:db8:0:5::10:1/64 Interface Address: FE80::212:79FF:FE88:4D00 Backup Designated Router (ID): 2001:db8:0:5::10:2/64 Interface Address: FE80::218:71FF:FEC4:F00 Timer interval configured, Hello: 10 Dead: 40 Wait: 40 Retransmit: 5 Hello due in 00:00:09 Neighbor Count is 0 Adjacent neighbor count is 0
Common-CLI-Phase-3-Sept-2012.book Page 221 Sunday, September 9, 2012 6:00 PM
2-222
Display Commandsdisplay ospfv3 interface
Cost: Cost value of the interface.
Transmit Delay: Transmission delay of the interface.
State: Interface state:
• Down: No protocol traffic will be sent or received on the interface.
• Waiting: In this state, the router is trying to determine the identity of the (Backup) Designated Router for this network.
• p-2-p: The interface is in point-to-point state and will skip the waiting period and DR/BDR election.
• DR: The router itself is the designated router on the attached network.
• BDR: The router itself is the backup designated router on the attached network.
• DROther: The interface is neither a Designated Router nor a backup Designated Router.
Priority: Router priority for the DR/BDR election.
Designated Router: The DR on the interface’s network segment.
Backup Designated Router: The BDR on the interface’s network segment.
Time Interval Configured: Time interval in seconds configured on the interface:
• Hello—Hello interval.
• Dead—Dead interval.
• Wait—After this timer expires, the interface quits from the waiting state.
• Retransmit—LSA retransmission interval.
Hello due in: Hello packet will be sent in the indicated number of seconds.
Neighbor Count: Number of neighbors on the interface.
Adjacent Neighbor Count: Number of adjacencies on the interface.
Operating Notes
To enable OSPF operation in ProVision software, enter the following com-mands in the global configuration context:
ipv6 unicast-routing
router ospf3 enable
Common-CLI-Phase-3-Sept-2012.book Page 222 Sunday, September 9, 2012 6:00 PM
2-223
Display Commandsdisplay ospfv3 interface
For more on configuring OSPFv3, including additional OSPFv3 configuration commands, see the “OSPFv3 Routing” chapter in the latest IPv6 Configura-
tion Guide for your switch.
Example of Related ProVision Software Command Output.
OSPF Interface Field Mappings.
HP Switch(config)# show ipv6 ospf3 interface 75 detail
OSPFv3 configuration and statistics for VLAN 75
Interface : vlan-75 Status : Enabled Area ID : 0.0.0.3 State : WAIT Priority : 1 Cost : 1 Type : BCAST Passive : Yes Hello Interval : 10 Dead Interval : 40 Transit Delay : 1 Retransmit Interval : 5 Events : 0 Designated Router : 15.1.1.2 Neighbors : 1 Backup Designated Router : 15.1.4.4
Comware ProVision Software
Interface ID Interface
n/a Status
IPv6 Prefixes n/a
OSPF Process n/a
Area Area ID
Instance ID n/a
Router ID n/a
Network Type Type
Cost Cost
Transmit Delay Transit Delay
State State
Priority Priority
Designated Router Designated Router
Backup Designated Router Backup Desig. Rtr
Common-CLI-Phase-3-Sept-2012.book Page 223 Sunday, September 9, 2012 6:00 PM
2-224
Display Commandsdisplay ospfv3 interface
Minimum Software Version: 15.09.
n/a Passive
Time Interval Configured Retransmit Interval
Hello due in n/a
Neighbor Count Neighbors
Adjacent Neighbor Count n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 224 Sunday, September 9, 2012 6:00 PM
2-225
Display Commandsdisplay ospfv3 lsdb
display ospfv3 lsdb
Displays OSPFv3 LSDB information. This command is available only in man-ager mode.
HP Switch# display ospfv3 lsdb OSPFv3 Router with ID (2.2.2.2) (Process 1) Link-LSA (Interface Vlan-interface1)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Prefix5.178.0.0 1.1.1.1 1082 0x8000000c 0x31c7 15.178.0.0 2.2.2.2 0896 0x8000000b 0xe23c 1
Link-LSA (Interface Vlan-interface2)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Prefix5.178.0.1 2.2.2.2 0896 0x8000000b 0x0f0d 15.178.0.1 3.3.3.3 0654 0x8000000b 0xcf90 1
Router-LSA (Area 0.0.0.0)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Link0.0.0.0 1.1.1.1 0892 0x8000000e 0x8e0c 10.0.0.0 2.2.2.2 0376 0x8000000d 0x7b19 1
Network-LSA (Area 0.0.0.0)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum 5.178.0.0 1.1.1.1 0887 0x80000016 0xcc7f
Inter-Area-Prefix-LSA (Area 0.0.0.0)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum0.0.0.1 2.2.2.2 0886 0x8000000b 0x7962
Intra-Area-Prefix-LSA (Area 0.0.0.0)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Prefix Reference0.0.0.2 1.1.1.1 0892 0x8000000b 0x05ee 1 Network-LSA
Router-LSA (Area 0.0.0.1)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Link0.0.0.0 2.2.2.2 0376 0x80000010 0xe7a3 10.0.0.0 3.3.3.3 0649 0x8000000c 0xc8c5 1
Network-LSA (Area 0.0.0.1)
Comware Related ProVision
display ospfv3 lsdb show ipv6 ospf3 link-state
Common-CLI-Phase-3-Sept-2012.book Page 225 Sunday, September 9, 2012 6:00 PM
2-226
Display Commandsdisplay ospfv3 lsdb
---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum5.178.0.1 2.2.2.2 0371 0x80000018 0xf448
Inter-Area-Prefix-LSA (Area 0.0.0.1)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum0.0.0.1 2.2.2.2 0891 0x8000000b 0x6d6f
Intra-Area-Prefix-LSA (Area 0.0.0.1)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Prefix Reference0.0.0.2 2.2.2.2 0651 0x8000000b 0x37b2 1 Network-LSA
AS-external-LSA---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum0.0.0.1 2.2.2.2 0375 0x8000000b 0x999a0.0.0.2 2.2.2.2 0570 0x80000002 0x6ebc
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 226 Sunday, September 9, 2012 6:00 PM
2-227
Display Commandsdisplay ospfv3 lsdb statistics
display ospfv3 lsdb statistics
Displays LSA statistics in the OSPFv3 LSDB. This command is available only in manager mode.
HP Switch# display ospfv3 lsdb statistics OSPFv3 Router with ID (2.2.2.2) (Process 1) LSA Statistics --------------------------------------------------------------------- Area ID Router Network IntePre InteRou IntraPre Link Grace ASE 0.0.0.0 5 5 5 5 5 0.0.0.1 5 5 5 5 5 Total 10 10 10 10 10 5 0 5
Minimum Software Version: 15.10.
Comware Related ProVision
display ospfv3 lsdb statistics No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 227 Sunday, September 9, 2012 6:00 PM
2-228
Display Commandsdisplay ospfv3 peer
display ospfv3 peer
Displays OSPFv3 neighbor information.
Field Descriptions
Neighbor ID: Router ID of a neighbor.
Pri: Priority of neighbor router for DR/BDR election.
State: Neighbor state.
Dead time: Dead time remaining
Interface: Interface connected to the neighbor.
Instance ID: Instance ID.
Operating Notes
For more on switch OSPFv3 operation, refer to the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide for your switch.
Comware Related ProVision
display ospfv3 peer show ipv6 ospf3 neighbor
HP Switch(vlan-2)# display ospfv3 peer
OSPFv3 Area ID 0.0.0.1 (Process 1)
Neighbor ID Pri State Dead Time Interface Instance ID -------------------------------------------------------------------------- 120.85.228.88 1 FULL 00:00:33 Vlan2 0
Common-CLI-Phase-3-Sept-2012.book Page 228 Sunday, September 9, 2012 6:00 PM
2-229
Display Commandsdisplay ospfv3 peer
Example of Related ProVision Software Command Output.
display ospfv3 peer Field Mappings.
Minimum Software Version: 15.09.
HP Switch(ospf3)# show ipv6 ospf3 neighbor
OSPFv3 Neighbor Information
Interface Router ID Pri State Rxmt QLen Events --------- --------------- ----- ---------- ---------- ---------- Vlan-55 15.1.0.1 1 Full 0 0 Vlan-75 15.1.1.2 1 Full 0 0 tunnel-3 4.3.2.1 1 Full 0 0
Comware ProVision Software
Neighbor ID Router ID
Interface Interface
n/a Router ID
Pri Pri
State State
Dead time n/a
Instance ID n/a
n/a Rxmt QLen
n/a Events
Common-CLI-Phase-3-Sept-2012.book Page 229 Sunday, September 9, 2012 6:00 PM
2-230
Display Commandsdisplay ospfv3 peer peer-router-id
display ospfv3 peer peer-router-id
Displays the router ID of the specified neighbor.
Field Descriptions
Neighbor: Neighbor ID.
Interface Address: Interface Address.
Vlan-interface: Vlan-interface <vid> belongs to area <area>.
DR/BDR: Router Id of the Designated Router and the Backup Designated Router.
Options: Displays the capabilities.
Dead timer: Indicates when the dead timer is due.
Neighbor up: Neighbor has been up for the indicated time.
Database Summary List: Number of LSAs sent in the DD packet.
Link State Request List: Number of LSAs in the link state request list.
Link State Retransmission List: Number of LSAs in the link state retransmission list.
Comware Related ProVision
display ospfv3 peer peer-router-id show ipv6 ospf3 neighbor <router-id> detail
HP Switch# display ospfv3 peer 2.2.2.2 Neighbor 2.2.2.2 is Full, interface address FE80::223:89FF:FECB:6FDC In the area 0.0.0.0 via interface Vlan-interface1 DR is 2.2.2.2 BDR is 1.1.1.1 Options is 0x000013 (-|R|-|-|E|V6) Dead timer due in 00:00:35 Neighbor is up for 00:04:35 Database Summary List 0 Link State Request List 0 Link State Retransmission List 0 Graceful restart state: Normal
Common-CLI-Phase-3-Sept-2012.book Page 230 Sunday, September 9, 2012 6:00 PM
2-231
Display Commandsdisplay ospfv3 peer peer-router-id
Graceful restart state: Graceful restart status can be:
• Normal: Normal status
• Helper: The device is a Graceful Restart Helper of the neighbor.
Operating Notes
For more on switch OSPFv3 operation, refer to the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
display ospfv3 peer verbose Field Mappings.
HP Switch(ospf3)# show ipv6 ospf3 neighbor 15.1.0.1 detail
OSPFv3 Neighbor Information for neighbor 15.1.0.1
IPv6 Address : fe80::55:1 Router ID : 15.1.0.1 State : FULL Interface : vlan-55 Designated Router : 15.1.0.1 Area : 0.0.0.1 Backup Designated Router : 15.1.0.4 Priority : 1 Retransmit Queue Length : 0 Options : 19 Neighbor Uptime : 1days Events : 0 Dead Timer Expires : 33 sec
Comware ProVision Software
Neighbor Neighbor
Interface Address IPv6 Address
Vlan-interface Interface
DR/BDR Designated Router/Backup Designated Router
Options Options
Dead timer Dead Timer expires
Neighbor up Neighbor Uptime
Database Summary List n/a
Link State Request n/a
Link State Retransmission List
Retransmit Queue Length
Common-CLI-Phase-3-Sept-2012.book Page 231 Sunday, September 9, 2012 6:00 PM
2-232
Display Commandsdisplay ospfv3 peer peer-router-id
Minimum Software Version: 15.09.
Graceful Restart n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 232 Sunday, September 9, 2012 6:00 PM
2-233
Display Commandsdisplay ospfv3 peer statistics
display ospfv3 peer statistics
Displays information about all OSPFv3 neighbors on the router, that is, number of neighbors in different states.
HP Switch# display ospfv3 peer statistics OSPFv3 Router with ID (2.2.2.2) (Process 1) Neighbor Statistics---------------------------------------------------------------------Area ID Down Attempt Init 2-Way ExStart Exchange Loading Full0.0.0.0 0 0 0 0 0 0 0 10.0.0.1 0 0 0 0 0 0 0 1Total 0 0 0 0 0 0 0 2
Minimum Software Version: 15.10.
Comware Related ProVision
display ospfv3 peer statistics No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 233 Sunday, September 9, 2012 6:00 PM
2-234
Display Commandsdisplay ospfv3 peer verbose
display ospfv3 peer verbose
Displays detailed information about OSPFv3 neighbors.
Field Descriptions
Neighbor: Neighbor ID.
Interface Address: Interface Address.
Vlan-interface: Vlan-interface <vid> belongs to area <area>.
DR/BDR: Router-Id of the Designated Router and the Backup Designated Router.
Options: Displays the capabilities.
Dead timer: Indicates when the dead timer is due.
Neighbor up: Neighbor has been up for the indicated time.
Database Summary List: Number of LSAs sent in the DD packet.
Link State Request List: Number of LSAs in the link state request list.
Link State Retransmission List: Number of LSAs in the link state retransmission list.
Comware Related ProVision
display ospfv3 peer verbose show ipv6 ospf3 neighbor detail
HP Switch# display ospfv3 peer verbose
Neighbor 2.2.2.2 is Full, interface address FE80::223:89FF:FECB:6FDC In the area 0.0.0.0 via interface Vlan-interface1 DR is 2.2.2.2 BDR is 1.1.1.1 Options is 0x000013 (-|R|-|-|E|V6) Dead timer due in 00:00:30 Neighbor is up for 00:00:20 Database Summary List 0 Link State Request List 0 Link State Retransmission List 0 Graceful restart state: Normal
Common-CLI-Phase-3-Sept-2012.book Page 234 Sunday, September 9, 2012 6:00 PM
2-235
Display Commandsdisplay ospfv3 peer verbose
Graceful restart state: Graceful restart status can be:
• Normal: Normal status
• Helper: The device is a Graceful Restart Helper of the neighbor.
Operating Notes
For more on switch OSPFv3 operation, refer to the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
display ospfv3 peer verbose Field Mappings.
HP Switch(ospf3)# show ipv6 ospf3 neighbor 15.1.0.1 detail
OSPFv3 Neighbor Information for neighbor 15.1.0.1
IPv6 Address : fe80::55:1 Router ID : 15.1.0.1 State : FULL Interface : vlan-55 Designated Router : 15.1.0.1 Area : 0.0.0.1 Backup Designated Router : 15.1.0.4 Priority : 1 Retransmit Queue Length : 0 Options : 19 Neighbor Uptime : 1days Events : 0 Dead Timer Expires : 33 sec
Comware ProVision Software
Neighbor Neighbor
Interface Address IPv6 Address
Vlan-interface Interface
DR/BDR Designated Router/Backup Designated Router
Options Options
Dead timer Dead Timer expires
Neighbor up Neighbor Uptime
Database Summary List n/a
Link State Request n/a
Link State Retransmission List
Retransmit Queue Length
Common-CLI-Phase-3-Sept-2012.book Page 235 Sunday, September 9, 2012 6:00 PM
2-236
Display Commandsdisplay ospfv3 peer verbose
Minimum Software Version: 15.09.
Graceful Restart n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 236 Sunday, September 9, 2012 6:00 PM
2-237
Display Commandsdisplay ospfv3 statistic
display ospfv3 statistic
Displays outbound/inbound OSPFv3 packet statistics on associated inter-face(s).
Field Descriptions
Interface: Interface name.
Instance: Instance number.
Type: Type of packet.
Input: Number of packets received by the interface.
Output: Number of packets sent by the interface.
Hello: Hello packet.
DB Description: Database description packet.
Ls Req: Link state request packet
Ls Upd: Link state update packet
Ls Ack: Link state acknowledgement packet
Discarded: Number of discarded packets.
Comware Related ProVision
display ospfv3 statistic show ipv6 ospf3 statistics
HP Switch(vlan-2)# display ospfv3 statistics
OSPFv3 Statistics Interface 2 Instance 0 Type Input Output Hello 6 10 DB Description 2 5 Ls Req 1 1 Ls Upd 2 3 Ls Ack 2 2 Discarded 32 1
Common-CLI-Phase-3-Sept-2012.book Page 237 Sunday, September 9, 2012 6:00 PM
2-238
Display Commandsdisplay ospfv3 statistic
Operating Notes
For more on switch OSPFv3 operation, refer to the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
Per-VLAN OSPF Statistics
Field Content
OSPF statistics for VLAN <vlan-id>
OSPF statistics displayed for the specified VLAN number
OSPF Interface Status for <ip-address>
IP address of a subnet on the VLAN
Tx/Rx Hello Packet Count
Number of OSPF hello packets sent/received on each subnet interface
Tx/Rx DD Packet Count
Number of link-state database description packets sent/received on each subnet interface
Tx/Rx LSR Packet Count
Number of link-state request packets sent/received on each subnet interface
Tx/Rx LSU Packet Count
Number of link-state update packets sent/received on each subnet interface
Tx/Rx LSA Packet Count
Number of link-state acknowledgement packets sent/received on each subnet interface
OSPF errors Number of errors detected on the VLAN subnet during OSPF packet exchange
Common-CLI-Phase-3-Sept-2012.book Page 238 Sunday, September 9, 2012 6:00 PM
2-239
Display Commandsdisplay ospfv3 statistic
display ospfv3 statistic Field Mappings.
Minimum Software Version: 15.09.
HP Switch# show ipv6 ospf3 statistics vlan 55
OSPFv3 statistics for VLAN 55
Tx Hello Packets : 26005 Rx Hello Packets : 26005 Tx DD Packets : 3 Rx DD Packets : 3 Tx LSR Packets : 1 Rx LSR Packets : 1 Tx LSU Packets : 1436 Rx LSU Packets : 1046 Tx LSA Packets : 615 Rx LSA Packets : 1444
OSPFv3 Errors : 0
Comware ProVision Software
Interface OSPF statistics for
Instance n/a
Type n/a
Input n/a
Output n/a
Hello Tx/Rx Hello Packets
DB Description Tx/Rx DD Packets
Ls Req Tx/Rx LSR Packets
Ls Upd Tx/Rx LSU Packets
Ls Ack Tx/Rx LSA Packets
Discarded Total Errors
Common-CLI-Phase-3-Sept-2012.book Page 239 Sunday, September 9, 2012 6:00 PM
2-240
Display Commandsdisplay ospfv3 vlink
display ospfv3 vlink
Displays OSPFv3 virtual link information.
Field Descriptions
Virtual Link: The virtual link name and destination router ID.
Transit area: The VLAN interface ID and transit area.
Instance ID: Instance identity.
Local address: The local router IPv6 address.
Remote address: The remote router IPv6 address.
Transmit Delay: The transmit delay for sending LSAs.
State: The state of the interface, such as P-To-P.
Timer intervals: The configured timer intervals for Hello, Dead, Wait, and Retransmit.
Hello due in: The interval until the next Hello packet is sent.
Adjacency state: The current virtual neighbor adjacency state
Comware Related ProVision
display ospfv3 vlink show ipv6 ospf3 virtual-link ?
HP Switch# display ospfv3 vlink
Virtual Link VLINK1 to router 1.1.1.1 is up
Transit area :0.0.0.1 via interface Vlan-interface11, instance ID: 0
Local address: 2000:1::1
Remote address: 2001:1:1::1
Transmit Delay is 1 sec, State: P-To-P,
Timer intervals configured, Hello: 10, Dead: 40, Wait: 40, Retransmit: 5
Hello due in 00:00:02
Adjacency state :Full
Common-CLI-Phase-3-Sept-2012.book Page 240 Sunday, September 9, 2012 6:00 PM
2-241
Display Commandsdisplay ospfv3 vlink
Operating Notes
To configure OSPFv3 operation in ProVision software, see the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ipv6 ospf3 virtual-link
OSPFv3 Virtual Interface Status
Transit AreaID Neighbor Router Interface State
--------------- --------------- --------------- 0.0.0.1 1.1.1.1 P2P
ospfv3 vlink Field Mappings.
Minimum Software Version: 15.08.
Comware ProVision Software
Virtual Link Neighbor Router
Transit area Transit AreaID
Local address n/a
Remote address n/a
Transmit Delay n/a
State Interface State
Timer intervals n/a
Hello due n/a
Adjacency state n/a
Common-CLI-Phase-3-Sept-2012.book Page 241 Sunday, September 9, 2012 6:00 PM
2-242
Display Commandsdisplay pim bsr-info
display pim bsr-info
Displays the BSR information in the PIM domain and the locally configured C-RP information in effect.
Field Descriptions
VPN-Instance: public net: Public network.
Elected BSR Address: Address of the elected BSR.
Candidate BSR Address: Address of the candidate BSR.
Priority: BSR priority.
Comware Related ProVision
display pim bsr-info show ip pim bsr
HP Switch# display pim bsr-info Elected BSR Address : 10.10.10.11 Priority : 0 Hash mask length : 30 State: n/a Scope: n/a Uptime : 00:08:00 Next BSR message scheduled at : 01:20:00 Candidate BSR Address : 10.10.10.10 Priority : 0 Hash mask length : 30 State: n/a Scope: n/a Candidate RP: 10.10.10.10(Vlan-interface10) Priority : 192 HoldTime : 192 Advertisement Interval : 192 Next advertisement scheduled at: n/a Candidate RP: 10.10.10.10(Vlan-interface20) Priority : 192 HoldTime : 192 Advertisement Interval : 192 Next advertisement scheduled at: n/a Candidate RP: 10.10.10.10(Vlan-interface30) Priority : 192 HoldTime : 192 Advertisement Interval : 192 Next advertisement scheduled at: n/a
Common-CLI-Phase-3-Sept-2012.book Page 242 Sunday, September 9, 2012 6:00 PM
2-243
Display Commandsdisplay pim bsr-info
Hash mask length: Hash mask length.
State: BSR state.
Scope: Scope of the BSR.
Uptime: Length of time for which this BSR has been up, in hh:mm:ss.
Next BSR message scheduled at: Length of time in which the BSR will expire, in hh:mm:ss.
Candidate RP: Address of the C-RP.
Priority: Priority of the C-RP.
HoldTime: Timeout time of the C-RP.
Advertisement Interval: Interval at which the C-RP sends advertisement mes-sages.
Next advertisement scheduled at: Length of time in which the C-RP will send the next advertisement message, in hh:mm:ss.
Operating Notes
For more information on PIM, see the “PIM-SM (Sparse Mode)” or the “PIM-DM (Dense Mode) chapters in the latest Multicast and Routing Guide for your switch.
Common-CLI-Phase-3-Sept-2012.book Page 243 Sunday, September 9, 2012 6:00 PM
2-244
Display Commandsdisplay pim bsr-info
Example of Related ProVision Software Command Output.
display pim bsr-info Field Mappings.
HP Switch(config)# show ip pim bsr
Status and Counters - PIM-SM Bootstrap Router Information
E-BSR Address : 10.10.10.2 E-BSR Priority : 0 E-BSR Hash Mask Length : 30 E-BSR Up Time : 53 mins Next Bootstrap Message : 88 secs
C-BSR Admin Status : This system is a Candidate-BSR C-BSR Address : 10.10.10.1 C-BSR Priority : 0 C-BSR Hash Mask Length : 30 C-BSR Message Interval : 60 C-BSR Source IP VLAN : 100
C-RP Admin Status : This system is a Candidate-RP C-RP Address : 10.10.10.1 C-RP Hold Time : 150 C-RP Advertise Period : 60 C-RP Priority : 192 C-RP Source IP VLAN : 100
Group Address Group Mask --------------- --------------- 224.0.0.0 240.0.0.0 229.0.1.0 255.255.255.0 239.100.128.0 255.255.128.0
Elected BSR for the PIM-SM Domain
Candidate-BSR Configuration for the Current Routing Switch
Candidate-RP Configuration for the Current Routing Switch
Multicast Groups for which the Current Routing Switch Is Configured as a Candidate-RP
Comware ProVision Software
VPN-Instance public net n/a
Elected BSR Address E-BSR Address
Candidate BSR Address C-BSR Address
Priority E-BSR Priority
Hash mask length E-BSR Hash Mask Length
Common-CLI-Phase-3-Sept-2012.book Page 244 Sunday, September 9, 2012 6:00 PM
2-245
Display Commandsdisplay pim bsr-info
Minimum Software Version: 15.09.
State n/a
Scope n/a
Uptime E-BSR Uptime
Next BSR messaged scheduled at Next Bootstrap Message
Candidate RP C-RP Address
Priority C-RP Priority
HoldTime C-RP Hold Time
Advertisement Interval C-RP Advertise Period
Next advertisement scheduled at n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 245 Sunday, September 9, 2012 6:00 PM
2-246
Display Commandsdisplay pim control-message counters
display pim control-message counters
Displays statistics information of PIM control messages.
HP Switch# display pim control-message countersVPN-Instance: n/a PIM global control-message counters: Received Sent Invalid Register 0 0 0 Register-Stop 0 0 0 Probe n/a n/a n/a
PIM control-message counters for interface: Vlan-interface10 Received Sent Invalid Assert 0 0 0 Graft 0 0 0 Graft-Ack 0 0 0 Hello 0 0 0 Join/Prune 0 0 0 State-Refresh 0 0 0 BSR 0 0 0 C-RP 0 0 0
PIM control-message counters for interface: Vlan-interface30 Received Sent Invalid Assert 0 0 0 Graft 0 0 0 Graft-Ack 0 0 0 Hello 0 0 0 Join/Prune 0 0 0 State-Refresh 0 0 0 BSR 0 0 0 C-RP 0 0 0
Minimum Software Version: 15.10.
Comware Related ProVision
display pim control-message counters No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 246 Sunday, September 9, 2012 6:00 PM
2-247
Display Commandsdisplay pim grafts
display pim grafts
Displays information about unacknowledged PIM-DM graft messages.
HP Switch# display pim grafts
vlan 1 name "DEFAULT_VLAN" no untagged 1-2,48 untagged 3-47 ip address dhcp-bootp exit
vlan 10 name "VLAN10" untagged 1,48 ip address 10.10.10.3 255.255.255.0 ip igmp exit
vlan 30 name "VLAN30" untagged 2 ip address 30.30.30.2 255.255.255.0 ip igmp ip rip 30.30.30.2 ip pim-sparse ip-addr any exit exit
Minimum Software Version: 15.10.
Comware Related ProVision
display pim grafts No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 247 Sunday, September 9, 2012 6:00 PM
2-248
Display Commandsdisplay pim interface
display pim interface
Displays the PIM information on the specified interface or all interfaces.
Field Descriptions
VPN-Instance: public net: Public network.
Interface: Interface name.
NbrCnt: Number of PIM neighbors.
HelloInt: Hello interval.
DR-Pri: Priority for DR election.
DR-Address: DR IP address, where “local” indicates a local address
Operating Notes
For more information on PIM, see the “PIM-SM (Sparse Mode)” or the “PIM-DM (Dense Mode) chapters in the latest Multicast and Routing Guide for your switch.
Comware Related ProVision
display pim interface <interface> show ip pim interface
HP Switch# display pim interfaceVPN-Instance: n/aInterface NbrCnt HelloInt DR-Pri DR-AddressVlan10 n/a 30 1 10.10.10.11Vlan20 n/a 30 1 20.20.20.20Vlan30 n/a 30 1 30.30.30.30
Common-CLI-Phase-3-Sept-2012.book Page 248 Sunday, September 9, 2012 6:00 PM
2-249
Display Commandsdisplay pim interface
Example of Related ProVision Software Command Output.
display pim interface Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
VPN-Instance public net n/a
Interface VLAN
NbrCnt n/a
HelloInt n/a
DR-Pri n/a
DR-Address IP Address
n/a Mode
HP Switch(config)# show ip pim interface
PIM Interfaces
VLAN IP Address Mode ---- --------------- ------------ 1 10.1.10.1 sparse 2 10.2.10.1 sparse
Common-CLI-Phase-3-Sept-2012.book Page 249 Sunday, September 9, 2012 6:00 PM
2-250
Display Commandsdisplay pim interface verbose
display pim interface verbose
Displays detailed PIM information.
Field Descriptions
VPN-Instance Public net: Public network.
Interface: Interface name and its IP address.
PIM version: Running PIM version.
PIM mode: PIM mode, dense or sparse.
Comware Related ProVision
display pim interface verbose show ip pim interface <int>
HP Switch# display pim interface verboseInterface : Vlan-interface10, 10.10.10.10 PIM version : n/a PIM mode : 2 PIM DR : 10.10.10.10 PIM DR Priority (configured) : 1 PIM neighbor count: n/a PIM hello interval : 30 PIM LAN delay (negotiated): n/a PIM LAN delay (configured) : 500 PIM override interval (negotiated): n/a PIM override interval (configured) : 2500 PIM neighbor tracking (negotiated): n/a PIM neighbor tracking (configured): n/a PIM generation ID : 2 PIM require generation ID: n/a PIM hello hold interval : 105 PIM assert hold interval: n/a PIM triggered hello delay : 5 PIM J/P interval : 60 PIM J/P hold interval: n/a PIM state-refresh processing : 1 PIM state-refresh interval : 0 PIM state-refresh rate limit: n/a PIM state-refresh TTL : 0 PIM graft retry interval : 3 Number of routers on network not using DR priority: n/a Number of routers on network not using LAN delay: n/a Number of routers on network not using neighbor tracking: n/a
Common-CLI-Phase-3-Sept-2012.book Page 250 Sunday, September 9, 2012 6:00 PM
2-251
Display Commandsdisplay pim interface verbose
PIM DR: DR IP address.
PIM DR Priority (configured): Configured priority for DR election.
PIM neighbor count: Total number of PIM neighbors.
PIM hello interval: Hello interval.
PIM LAN delay (negotiated): Negotiated prune message delay.
PIM LAN delay (configured): Configured prune message delay.
PIM override interval (negotiated): Negotiated prune override interval.
PIM override interval (configured): Configured prune override interval.
PIM neighbor tracking (negotiated): Negotiated neighbor tracking status (enabled/disabled).
PIM neighbor tracking (configured): Configured neighbor tracking status (enabled/disabled).
PIM generation ID: Generation_ID value.
PIM require generation ID: Rejection of Hello messages without Generation_ID (enabled/disabled).
PIM hello hold interval: PIM neighbor timeout time.
PIM assert hold interval: Assert timeout time.
PIM triggered hello delay: Maximum delay of sending hello messages.
PIM J/P interval: Join/prune interval.
PIM J/P hold interval: Join/prune timeout time.
PIM BSR domain border: Status of PIM domain border configuration (enabled/disabled).
Number of routers on network not using DR priority: Number of routers not using the DR priority field on the subnet where the interface resides.
Number of routers on network not using LAN delay: Number of routers not using the LAN delay field on the subnet where the interface resides.
Number of routers on network not using neighbor tracking: Number of routers not using neighbor tracking on the subnet where the interface resides.
Common-CLI-Phase-3-Sept-2012.book Page 251 Sunday, September 9, 2012 6:00 PM
2-252
Display Commandsdisplay pim interface verbose
Operating Notes
For more information on PIM, see the “PIM-SM (Sparse Mode)” or the “PIM-DM (Dense Mode) chapters in the latest Multicast and Routing Guide for your switch.
Example of Related ProVision Software Command Output.
display pim interface Field Mappings.
HP Switch(config)# show ip pim interface 1
PIM Interface
VLAN : 1 IP Address : 10.1.10.1 Mode : sparse
Designated Router : 10.1.10.1
Hello Interval (sec) : 30 Hello Delay (sec) : 5
Override Interval (msec) : 2500 Lan Prune Delay : Yes Propagation Delay (msec) : 500 Lan Delay Enabled : No Neighbour Timeout : 180 DR Priority : 1
Comware ProVision Software
VPN-Instance public net n/a
Interface VLAN
PIM Version n/a
PIM mode Mode
PIM DR Designated Router
PIM DR Priority (configured) DR Priority
PIM neighbor count n/a
PIM hello interval Hello Interval (sec)
PIM LAN delay (negotiated) n/a
Common-CLI-Phase-3-Sept-2012.book Page 252 Sunday, September 9, 2012 6:00 PM
2-253
Display Commandsdisplay pim interface verbose
Minimum Software Version: 15.09.
PIM LAN delay (configured) Hello Delay
PIM override interval (negotiated) n/a
PIM override interval (configured) Override Interval (msec0
PIM neighbor tracking (negotiated) n/a
PIM neighbor tracking (configured) n/a
PIM generation ID n/a
PIM require generation ID n/a
PIM hello hold interval Hello Delay (sec)
PIM assert hold interval n/a
PIM triggered hello delay n/a
PIM J/P interval n/a
PIM J/P hold interval n/a
PIM state-refresh processing n/a
PIM state-refresh interval n/a
PIM state-refresh rate-limit n/a
PIM state-refresh TTL n/a
PIM graft retry interval n/a
Number of routers on network not using DR priority
n/a
Number of routers on network not using LAN delay
n/a
Number of routers on network not using neighbor tracking
n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 253 Sunday, September 9, 2012 6:00 PM
2-254
Display Commandsdisplay pim join-prune
display pim join-prune
HP Switch# display pim join-prune mode sm VPN-Instance: public net Expiry Time: 51 sec Upstream nbr: 10.10.10.1 (Vlan-Interface10) 1 (*, G) join(s), 1 (S, G) join(s), 0 (S, G, rpt) prune(s)-------------------------------------------------------------Total (*, G) join(s): 1, (S, G) join(s): 1, (S, G, rpt) prune(s): 0|...+....1....+....2....+....3....+....4....+....5....+....6....+....7....+....8
Minimum Software Version: 15.10.
Comware Related ProVision
display pim join-prune No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 254 Sunday, September 9, 2012 6:00 PM
2-255
Display Commandsdisplay pim neighbor
display pim neighbor
Displays information about PIM neighbors.
Field Descriptions
VPN-Instance: public net: Public network
Total Number of Neighbors: Total number of PIM neighbors
Neighbor: IP address of the PIM neighbor
Interface: Interface connecting the PIM neighbor
Uptime: Length of time for which the PIM neighbor has been up, in hh:mm:ss
Expires/Expiry time: Remaining time of the PIM neighbor, in hh:mm:ss; “never” means that the PIM neighbor is always up and reachable.
Dr-Priority/DR Priority: Priority of the PIM neighbor
Mode: Mode of the PIM neighbor. The value “B” means the BIDIR-PIM mode. If nothing is displayed, it means the non-BIDIR-PIM mode.
Operating Notes
For more information on PIM, see the “PIM-SM (Sparse Mode)” or the “PIM-DM (Dense Mode) chapters in the latest Multicast and Routing Guide for your switch.
Comware Related ProVision
display pim neighbor show ip pim neighbor
HP Switch# display pim neighbor VPN-Instance: n/a Total Number of Neighbors = n/a Neighbor Interface Uptime Expires Dr-Priority Mode 10.1.1.2 Vlan100 02:50:49 00:01:31 n/a n/a 20.1.1.2 Vlan101 02:49:39 00:01:42 n/a n/a
Common-CLI-Phase-3-Sept-2012.book Page 255 Sunday, September 9, 2012 6:00 PM
2-256
Display Commandsdisplay pim neighbor
Example of Related ProVision Software Command Output.
display pim neighbor Field Mappings.
Minimum Software Version: 15.09.
HP Switch(config)# show ip pim neighbor
PIM Neighbors
IP Address VLAN Up Time (sec) Expire Time (sec) DR Priority --------------- ---- ---------------- ---------------- ---------- 10.10.10.2 100 348 90 1 10.20.10.1 200 410 97 1
Comware ProVision Software
VPN-Instance public net n/a
Total Number of Neighbors n/a
Neighbor IP Address
Interface VLAN
Uptime UP Time (sec)
Expires/Expiry time Expire Time (sec)
Dr-Priority/DR Priority DR Priority
Mode n/a
Common-CLI-Phase-3-Sept-2012.book Page 256 Sunday, September 9, 2012 6:00 PM
2-257
Display Commandsdisplay pim neighbor <ip> verbose
display pim neighbor <ip> verbose
Displays information about PIM neighbors.
Field Descriptions
VPN-Instance: public net: Public network
Total Number of Neighbors: Total number of PIM neighbors
Neighbor: IP address of the PIM neighbor
Interface: Interface connecting the PIM neighbor
Uptime: Length of time for which the PIM neighbor has been up, in hh:mm:ss
Expires/Expiry time: Remaining time of the PIM neighbor, in hh:mm:ss; “never” means that the PIM neighbor is always up and reachable.
Dr-Priority/DR Priority: Priority of the PIM neighbor
Mode: Mode of the PIM neighbor. The value “B” means the BIDIR-PIM mode. If nothing is displayed, it means the non-BIDIR-PIM mode.
Generation ID: Generation ID of the PIM neighbor (a random value indicating a status change of the PIM neighbor)
Comware Related ProVision
display pim neighbor <ip> verbose show ip pim neighbor
HP Switch# display pim neighbor 11.110.0.20 verbose VPN-Instance: n/a Neighbor: 11.110.0.20 Interface: Vlan-interface100 Uptime: 00:00:10 Expiry time: 00:00:30 DR Priority: n/a Generation ID: n/a Holdtime: n/a LAN delay: n/a Override interval: n/a State refresh interval: n/a Neighbor tracking: n/a Bidirectional PIM: n/a
Common-CLI-Phase-3-Sept-2012.book Page 257 Sunday, September 9, 2012 6:00 PM
2-258
Display Commandsdisplay pim neighbor <ip> verbose
Holdtime: Holdtime of the PIM neighbor; “forever” means that the PIM neighbor is always up and reachable
LAN delay: Prune message delay
Override interval: Prune override interval
State refresh interval: Interval for sending state refresh messages/ Displayed only when the PIM neighbor works in PIM-DM mode and the state refresh capability is enabled.
Neighbor tracking: Neighbor tracking status (enabled/disabled)
Bidirectional PIM: BIDIR-PIM status (enabled/disabled)
Operating Notes
For more information on PIM, see the “PIM-SM (Sparse Mode)” or the “PIM-DM (Dense Mode) chapters in the latest Multicast and Routing Guide for your switch.
Example of Related ProVision Software Command Output.
display pim neighbor Field Mappings.
HP Switch(config)# show ip pim neighbor
PIM Neighbors
IP Address VLAN Up Time (sec) Expire Time (sec) DR Priority --------------- ---- ---------------- ---------------- ---------- 10.10.10.2 100 348 90 1 10.20.10.1 200 410 97 1
Comware ProVision Software
VPN-Instance public net n/a
Total Number of Neighbors n/a
Neighbor IP Address
Interface VLAN
Uptime UP Time (sec)
Common-CLI-Phase-3-Sept-2012.book Page 258 Sunday, September 9, 2012 6:00 PM
2-259
Display Commandsdisplay pim neighbor <ip> verbose
Minimum Software Version: 15.09.
Expires/Expiry time Expire Time (sec)
Dr-Priority/DR Priority DR Priority
Mode n/a
Generation ID n/a
Holdtime n/a
LAN delay n/a
Override interval n/a
State refresh interval n/a
Neighbor tracking n/a
Bidirectional PIM n/a
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 259 Sunday, September 9, 2012 6:00 PM
2-260
Display Commandsdisplay pim routing-table
display pim routing-table
Displays the contents of the PIM multicast routing table, which includes SPT and RPF information.
HP Switch# display pim routing-tableVPN-Instance: public net Total 0 (*, G) entry; 1 (S, G) entry
(172.168.0.12, 227.0.0.1) Protocol: pim-sm, Flag: LOC UpTime: 02:54:43 Upstream interface: Vlan-interface20 Upstream neighbor: NULL RPF prime neighbor: NULL Downstream interface(s) information: Total number of downstreams: 1 1: Vlan-interface10 Protocol: pim-sm, UpTime: 02:54:43, Expires: 00:02:47
Minimum Software Version: 15.10.
Comware Related ProVision
display pim routing-table No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 260 Sunday, September 9, 2012 6:00 PM
2-261
Display Commandsdisplay pim rp-info
display pim rp-info
Displays information about pim RP.
HP Switch# display pim rp-info VPN-Instance: public net
PIM-SM BSR RP information:
Group/MaskLen: 224.0.0.0/4 RP: 10.10.10.11
Priority: n/a
HoldTime: 150 Uptime: n/a
Expires: 00:01:00
Minimum Software Version: 15.10.
Comware Related ProVision
display pim rp-info No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 261 Sunday, September 9, 2012 6:00 PM
2-262
Display Commandsdisplay poe device
display poe device
Displays the mapping between ID, module, and slot of the power sourcing equipment (PSE).
HP Switch# display poe device
PSE ID SlotNo SubSNo PortNum MaxPower(W) State Model A 1 n/a 24 370 off J9310A
Example of Related ProVision Software Command Output. HP Switch# show power-over-ethernet briefStatus and Counters - Port Power StatusSystem Power Status : No redundancyPoE Power Status : No redundancyAvailable: 300 W Used: 0 W Remaining: 300 WModule A PowerAvailable: 300 W Used: 5 W Remaining: 295 WPoE | Power Power Alloc Alloc Actual Configured Detection PowerPort | Enable Priority By Power Power Type Status Class------ + ------ -------- ----- ----- ------ ----------- ----------- -----A1 | Yes low usage 17 W 5.0 W Phone1 Delivering 1A2 | Yes low usage 17 W 0.0 W Searching 0A3 | Yes low usage 17 W 0.0 W Searching 0A4 | Yes low usage 17 W 0.0 W Searching 0A5 | Yes low usage 17 W 0.0 W Searching 0A6 | Yes low usage 17 W 0.0 W Searching 0
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display poe device show power-over-ethernet brief
Common-CLI-Phase-3-Sept-2012.book Page 262 Sunday, September 9, 2012 6:00 PM
2-263
Display Commandsdisplay poe interface
display poe interface
Displays the PoE status of a specific port on the switch.
HP Switch# display poe interface
Interface Enable Priority CurPower Operating IEEE Detection (W) Status Class Status
1 enable low 0.0 off 0 enabled 2 enable low 0.0 off 0 enabled 3 enable low 0.0 off 0 enabled 4 enable low 0.0 off 0 enabled 5 enable low 0.0 off 0 enabled 6 enable low 0.0 off 0 enabled 7 enable low 0.0 off 0 enabled 8 enable low 0.0 off 0 enabled 9 enable low 0.0 off 0 enabled 10 enable low 0.0 off 0 enabled 11 enable low 0.0 off 0 enabled 12 enable low 0.0 off 0 enabled 13 enable low 0.0 off 0 enabled 14 enable low 0.0 off 0 enabled 15 enable low 0.0 off 0 enabled 16 enable low 0.0 off 0 enabled 17 enable low 0.0 off 0 enabled 18 enable low 0.0 off 0 enabled 19 enable low 0.0 off 0 enabled 20 enable low 0.0 off 0 enabled 21 enable low 0.0 off 0 enabled 22 enable low 0.0 off 0 enabled 23 enable low 0.0 off 0 enabled 24 enable low 0.0 off 0 enabled
--- 24 port(s) on, 0.0 (W) consumed, 0.0 (W) remaining ---
Comware Related ProVision
display poe interface show power-over-ethernet brief
Common-CLI-Phase-3-Sept-2012.book Page 263 Sunday, September 9, 2012 6:00 PM
2-264
Display Commandsdisplay poe interface
Example of Related ProVision Software Command Output. HP Switch# show power-over-ethernet briefStatus and Counters - Port Power StatusSystem Power Status : No redundancyPoE Power Status : No redundancyAvailable: 300 W Used: 0 W Remaining: 300 WModule A PowerAvailable: 300 W Used: 5 W Remaining: 295 WPoE | Power Power Alloc Alloc Actual Configured Detection PowerPort | Enable Priority By Power Power Type Status Class------ + ------ -------- ----- ----- ------ ----------- ----------- -----A1 | Yes low usage 17 W 5.0 W Phone1 Delivering 1A2 | Yes low usage 17 W 0.0 W Searching 0A3 | Yes low usage 17 W 0.0 W Searching 0A4 | Yes low usage 17 W 0.0 W Searching 0A5 | Yes low usage 17 W 0.0 W Searching 0A6 | Yes low usage 17 W 0.0 W Searching 0
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 264 Sunday, September 9, 2012 6:00 PM
2-265
Display Commandsdisplay poe interface power
display poe interface power
Displays the PoE power information of the specified port on the switch. If you enter the command without an argument, the PoE power information about all PoE-capable ports on the switch is displayed.
HP Switch# display poe interface power
Interface CurPower PeakPower MaxPower PD Description (W) (W) (W)1 0.0 0.0 15.42 0.0 0.0 15.43 0.0 0.0 15.44 0.0 0.0 15.45 0.0 0.0 15.46 0.0 0.0 15.47 0.0 0.0 15.48 0.0 0.0 15.49 0.0 0.0 15.410 0.0 0.0 15.4 11 0.0 0.0 15.4 12 0.0 0.0 15.4 13 0.0 0.0 15.4 14 0.0 0.0 15.4 15 0.0 0.0 15.4 16 0.0 0.0 15.4 17 0.0 0.0 15.4 18 0.0 0.0 15.4 19 0.0 0.0 15.4 20 0.0 0.0 15.4 21 0.0 0.0 15.4 22 0.0 0.0 15.4 23 0.0 0.0 15.4 24 0.0 0.0 15.4
--- 0 port(s) on, 0.0 (W) consumed, 0.0 (W) remaining ---
Comware Related ProVision
display poe interface power show power-over-ethernet brief
Common-CLI-Phase-3-Sept-2012.book Page 265 Sunday, September 9, 2012 6:00 PM
2-266
Display Commandsdisplay poe interface power
Example of Related ProVision Software Command Output. HP Switch# show power-over-ethernet briefStatus and Counters - Port Power StatusSystem Power Status : No redundancyPoE Power Status : No redundancyAvailable: 300 W Used: 0 W Remaining: 300 WModule A PowerAvailable: 300 W Used: 5 W Remaining: 295 WPoE | Power Power Alloc Alloc Actual Configured Detection PowerPort | Enable Priority By Power Power Type Status Class------ + ------ -------- ----- ----- ------ ----------- ----------- -----A1 | Yes low usage 17 W 5.0 W Phone1 Delivering 1A2 | Yes low usage 17 W 0.0 W Searching 0A3 | Yes low usage 17 W 0.0 W Searching 0A4 | Yes low usage 17 W 0.0 W Searching 0A5 | Yes low usage 17 W 0.0 W Searching 0A6 | Yes low usage 17 W 0.0 W Searching 0
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 266 Sunday, September 9, 2012 6:00 PM
2-267
Display Commandsdisplay poe power-usage
display poe power-usage
Displays the power information of the PoE power and all PSEs.
HP Switch# display poe power-usagePoE Current Power : 0 WPoE Max Power : 37 WPoE Max Guaranteed Power : 0 WPoE Remaining Allocated Power : 0 WPoE Remaining Guaranteed Power : 0 WPoE Total Powered Port Number : 0 WDetailed power usage of PSE(s):PSE ID Max Current Peak Average Remaining Powered (W) (W) (W) (W) Guaranteed(W) PortNum7 37 0 0 0 37 010 37 0 0 0 37 0
Example of Related ProVision Software Command Output. HP Switch# show power-over-ethernet briefStatus and Counters - Port Power StatusSystem Power Status : No redundancyPoE Power Status : No redundancyAvailable: 300 W Used: 0 W Remaining: 300 WModule A PowerAvailable: 300 W Used: 5 W Remaining: 295 WPoE | Power Power Alloc Alloc Actual Configured Detection PowerPort | Enable Priority By Power Power Type Status Class------ + ------ -------- ----- ----- ------ ----------- ----------- -----A1 | Yes low usage 17 W 5.0 W Phone1 Delivering 1A2 | Yes low usage 17 W 0.0 W Searching 0A3 | Yes low usage 17 W 0.0 W Searching 0A4 | Yes low usage 17 W 0.0 W Searching 0A5 | Yes low usage 17 W 0.0 W Searching 0A6 | Yes low usage 17 W 0.0 W Searching 0
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display poe power-usage show power-over-ethernet brief
Common-CLI-Phase-3-Sept-2012.book Page 267 Sunday, September 9, 2012 6:00 PM
2-268
Display Commandsdisplay poe-power alarm
display poe-power alarm
Displays detailed alarm information about the PoE PSUs.
HP Switch# display poe-power alarm PSU alarm detail, PSU number : 2 PSU 1 alarm : POWERED PSU 2 alarm : POWERED
Example of Related ProVision Software Command Output.
HP Switch# show system power-supplyPower Supply Status: PS# | State | AC/DC + V | Wattage ----+-------------+-----------------+--------- 1 | Powered | AC 120VDL | 875 2 | Not Present | -- ---- | 0
1 / 2 supply bays delivering power. Total power: 875 W
Minimum Software Version: 15.10.
Comware Related ProVision
display poe-power alarm show system power-supply
Common-CLI-Phase-3-Sept-2012.book Page 268 Sunday, September 9, 2012 6:00 PM
2-269
Display Commandsdisplay poe-power switch state
display poe-power switch state
Displays the number and current state of the AC power distribution switches of the PSUs.
HP Switch# display poe-power switch state Switch Number : 3 Switch 1 State : AC Switch Off Switch 2 State : AC Switch High Voltage Switch 3 State : AC Switch Off
Minimum Software Version: 15.10.
Comware Related ProVision
display poe-power switch state No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 269 Sunday, September 9, 2012 6:00 PM
2-270
Display Commandsdisplay port trunk
display port trunk
Displays information about the hybrid or trunk ports on the switch, including port names, default VLAN IDs (untagged vlan), and allowed VLAN IDs (tagged vlan).
HP Switch# display port trunk Interface PVID VLAN passing A1 1 1-2, 5-10 A2 10 1, 5
Minimum Software Version: 15.10.
Comware Related ProVision
display port trunk No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 270 Sunday, September 9, 2012 6:00 PM
2-271
Display Commandsdisplay power
display power
Displays information about the power supply of a device.
Field Descriptions
Power: Number of power supply bay.
State: State of power supply.
Example of Related ProVision Software Command Output.
display power Field Mappings.
Minimum Software Version: 15.09.
Comware Related ProVision
display power show system power-supply
Comware ProVision Software
Power PS#
State State
HP Switch# display power Power 1 State: Powered Power 2 State: Powered Power 3 State: Not Present Power 4 State: Not Present
HP Switch(config)# show system power-supply
Power Supply Status: PS# | State | AC/DC + V | Wattage ----+-------------+-----------------+--------- 1 | Powered | -- ---- | 0
1 / 1 supply bays delivering power.
Common-CLI-Phase-3-Sept-2012.book Page 271 Sunday, September 9, 2012 6:00 PM
2-272
Display Commandsdisplay protocol-vlan
display protocol-vlan
Displays the protocols and protocol indexes configured on the specified VLANs.
HP Switch# display protocol-vlan VLAN ID:10 Protocol Index Protocol Type============================================= 1 IPv4 2 IPX 3 ARP
Minimum Software Version: 15.10.
Comware Related ProVision
display protocol-vlan No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 272 Sunday, September 9, 2012 6:00 PM
2-273
Display Commandsdisplay protocol-vlan interface
display protocol-vlan interface
Displays information about protocol-based VLANs on all ports.
HP Switch# display protocol-vlan interface all Interface: A1 VLAN ID Protocol Index Protocol Type ====================================================== 2 2 IPX Interface: F24 VLAN ID Protocol Index Protocol Type ====================================================== 4 5 Appletalk 4 1 IPv4 4 6 SNA
Minimum Software Version: 15.10.
Comware Related ProVision
display protocol-vlan interface No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 273 Sunday, September 9, 2012 6:00 PM
2-274
Display Commandsdisplay public-key local rsa public
display public-key local rsa public
Displays public key information of the local key pairs. This command is available only in manager mode.
HP Switch# display public-key local rsa public=====================================================Time of Key pair created: 16:53:41 2012/05/08Key name: HOST_KEYKey type: RSA Encryption Key=====================================================Key code:30819F300D06092A864886F70D010101050003818D0030818902818100C371A8F1C7BAC3B7BD9003B9B0F8F2D77980D160B998227F75F395CAD5663EEF16F9DC71CBD22149439F2BAC388B0F197141463129E6A5B83692D914A7DA8F34F0B8CB2C71C9DD7301D7231993AD357650731D4DC40B1DE825CB5B6FE8ED963AD7DFCF9AEF4A5E76DDBBA1ADD8AB533A4335963CE88825F7FFB1CB1F6DA5505D0203010001
=====================================================Time of Key pair created: n/aKey name: SERVER_KEYKey type: RSA Encryption Key=====================================================Key code:n/a
Example of Related ProVision Software Command Output.
HP Switch# show crypto host-public-keySSH host public key:ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQDNwBMXZ9vYG+YxtV+KQeQQ+R8RKx47lxs14jPImBoVqUmK1iyK3WGhv0Fsks9ZtATjidybwPjmfd2Lup1INUjemquL2C0YRXo4MULfrqioWTco4mlFliftypj5gLvYeYFT/9CpoxMF4YrTUyjc90UfIf3et3fahaZ4KgLQjnXV1b8AWWsDZRv7niq8A1emqgts3HuAk59L
Comware Related ProVision
display public-key local rsa public show crypto host-public-keyshow ip host-public-key
Common-CLI-Phase-3-Sept-2012.book Page 274 Sunday, September 9, 2012 6:00 PM
2-275
Display Commandsdisplay public-key local rsa public
vFYsMkvLV2a7qoks1auqW8otRHgv/QsWtxfuoYUvVnXDiZFKeent34+sQnIvy1wJAmukCmM3zp434eTeh87/2Oer612mlAwRq5qPFtTAZlsf8LGipjKftW6dq8uq9tYtTtQWO09Mi65L
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 275 Sunday, September 9, 2012 6:00 PM
2-276
Display Commandsdisplay public-key peer
display public-key peer
Displays brief information about all the public keys of remote hosts.
HP Switch# display public-key peer
Key Name : "rsa-key-20120206" Key Type : RSA Key Module : 1024 Key Code : raky2100"shraAABNa1cEAAJAABm2ufBHv80BmMgle//m9Hq8N4B1c+N1i3eUfyLN4bZBi2cIEXNU/cXDUo3FINB8k+xb2fhNfIQ8rT0Q0Y/a+XR=
Field Descriptions:
Key name: Key name, which can be one of the following values:
• HOST_KEY: Host public key
• SERVER_KEY: Server public key. This value is available only for RSA key pairs.
Key type: Key type, which can be one of the following values:
• RSA Encryption Key: RSA key pair
• DSA Encryption Key: DSA key pair
Key code: Key data
Example of Related ProVision Software Command Output.
HP Switch# show crypto client-public-key
Operator keys:
0,[email protected] ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAQEAsGffNl6CFBtxgEPExkZwbauXCiBLnzztD5qA2IafkQzOy22gMDAl6rinTXvDcdP6P+RDGX+76p0E4IabwnmdpdSX+jCCV7PDjYumrAomXF9uZ+6Mg6xkAURoXdisSwTiY9jeNyfCLrcLGy+4i9B2YEz3IO0qH7D8ciwfhTbkEnOCLIFGSYzGUGsbXbHRTd6prOogAIJg1lnXjSXLgHikdAtLFNNDwTXnxvX0SE02zeVehAb8XNHwZc6vy5FneKGjH9waq/TEEqVJPwAJ6A5diuUvaFlAQGj53y4QqdaMORcfRXMfGtOCsEx/jX5pmJAJ7MsB/NX1AHSowgRUaIR0qw==
Minimum Software Version: 15.09.
Comware Related ProVision
display public-key peer show ip client-public-key
Common-CLI-Phase-3-Sept-2012.book Page 276 Sunday, September 9, 2012 6:00 PM
2-277
Display Commandsdisplay radius scheme
display radius scheme
Displays the configuration information of RADIUS schemes.
Comware Related ProVision
display radius scheme show radiusshow radius host <host>show accounting
Common-CLI-Phase-3-Sept-2012.book Page 277 Sunday, September 9, 2012 6:00 PM
2-278
Display Commandsdisplay radius scheme
HP Switch# display radius scheme
------------------------------------------------------------------SchemeName : n/a Index : n/a Type : n/a Primary Auth Server : IP : 1.2.3.4 Port : 1812 State : n/a Encryption Key : samplee123 VPN instance : n/a Primary Acct Server : IP : 1.2.3.4 Port : 1813 State : n/a Encryption Key : samplee123 VPN instance : n/a Second Auth Server IP : 2.3.4.5 Port : 1812 State : n/a Encryption Key : ghefijklm VPN instance : n/a IP : 4.5.6.7 Port : 1812 State : n/a Encryption Key : abcdegh VPN instance : n/a IP : 4.5.6.8 Port : 1812 State : n/a Encryption Key : abcdegh VPN instance : n/a Second Acct Server IP : 2.3.4.5 Port : 1813 State : n/a Encryption Key : ghefijklm VPN instance : n/a IP : 4.5.6.7 Port : 1813 State : n/a Encryption Key : abcdegh VPN instance : n/a IP : 4.5.6.8 Port : 1813 State : n/a Encryption Key : abcdegh VPN instance : n/a Auth Server Encryption Key : Acct Server Encryption Key : VPN instance : n/a Accounting-On packet disable, send times : n/a , interval : n/a Interval for timeout(second) : 5 Retransmission times for timeout : 3 Interval for realtime accounting(minute) : 0 Retransmission times of realtime-accounting packet : 3 Retransmission times of stop-accounting packet : 3 Quiet-interval(min) : 0 Username format : n/a Data flow unit : n/a Packet unit : n/a NAS-IP address : n/a Attribute 25 : n/a ------------------------------------------------------------------Total 1 RADIUS scheme(s).
Common-CLI-Phase-3-Sept-2012.book Page 278 Sunday, September 9, 2012 6:00 PM
2-279
Display Commandsdisplay radius scheme
Field Descriptions
SchemeName: Name of the RADIUS scheme.
Index: Index number of the RADIUS scheme.
Type: Type of the RADIUS server, extended or standard.
Primary Auth Server: Information about the primary authentication server.
Primary Acct Server: Information about the primary accounting server.
Second Auth Server: Information about the secondary authentication server.
Second Acct Server: Information about the secondary accounting server.
IP: Ip address of the server.
Port: Service port of the server. If no port configuration is performed, the default port number is displayed.
State: Status of the server, active or blocked.
Encryption Key: Shared key for authenticating authentication or accounting packets, in cipher text or plain text. If no shared key is configured, the value of this field is N/A. This shared key is used only when no specific shared key is specified for the RADIUS server.
VPN instance: MPLS L3VPN that the server belongs to. If no VPN instance is specified for the server, the value of this field is N/A.
Auth Server Encryption Key: Shared key for authenticating authentication pack-ets, in cipher text or plain text.
Acct Server Encryption Key: Shared key for authenticating accounting packets, in cipher text or plain text.
Accounting-On packet disable: The accounting-on feature is disabled.
send times: Retransmission times of accounting-on packets.
interval: Interval at which the device retransmits accounting-on packets.
Interval for timeout (second): RADIUS server response timeout period, in sec-onds.
Retransmission times for timeout: Maximum number of attempts for transmitting a RADIUS packet to a single RADIUS server.
Common-CLI-Phase-3-Sept-2012.book Page 279 Sunday, September 9, 2012 6:00 PM
2-280
Display Commandsdisplay radius scheme
Interval for realtime accounting(minute): Interval for realtime accounting, in minutes.
Retransmission times of realtime-accounting packet: Maximum number of accounting attempts
Retransmission times of stop-accounting packet: Maximum number of stop-accounting attempts
Quiet-interval(min): Quiet interval for the primary server.
Username format: Format of the usernames to be sent to the RADIUS server.
Data flow unit: Unit for data flows sent to the RADIUS server.
Packet unit: Unit for packets sent to the RADIUS server.
NAS-IP address: Source IP address for RADIUS packets to be sent.
Attribute 25: Interprets RADIUS attribute 25 as the CAR parameters.
Operating Notes
For more information on switch RADIUS operation, see the “RADIUS Authen-tication, Authorization, and Accounting” chapter in the latest Access Security
Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch# show radius
Status and Counters - General RADIUS Information
Deadtime(min) : 5 Timeout(secs) : 10 Retransmit Attempts : 2 Global Encryption Key : myg10balkey Dynamic Authorization UDP Port : 3799 Source IP Selection : Outgoing Interface
Auth Acct DM/ Time Server IP Addr Port Port CoA Window Encryption Key OOBM --------------- ---- ---- --- ------ -------------------------------- ----- 192.33.12.65 1812 1813 No 300 my65key No
Common-CLI-Phase-3-Sept-2012.book Page 280 Sunday, September 9, 2012 6:00 PM
2-281
Display Commandsdisplay radius scheme
display radius scheme Field Mappings.
HP Switch(config)# show radius host 192.33.12.65 Status and Counters - RADIUS Server Information Server IP Addr : 192.33.12.65 Authentication UDP Port : 1812 Accounting UDP Port : 1813 Round Trip Time : 2 Round Trip Time : 7 Pending Requests : 0 Pending Requests : 0 Retransmissions : 0 Retransmissions : 0 Timeouts : 0 Timeouts : 0 Malformed Responses : 0 Malformed Responses : 0 Bad Authenticators : 0 Bad Authenticators : 0 Unknown Types : 0 Unknown Types : 0 Packets Dropped : 0 Packets Dropped : 0 Access Requests : 2 Accounting Requests : 2 Access Challenges : 0 Accounting Responses : 2 Access Accepts : 0 Access Rejects : 0
Comware ProVision Software
SchemeName n/a
Index n/a
Type n/a
Primary Auth Server Server IP Address
Primary Acct Server Server IP Address
Second Auth Server n/a
HP Switch(config)# show accounting
Status and Counters - Accounting Information
Interval(min) : 5 Suppress Empty User : No Sessions Identification : Common
Type | Method Mode Server Group -------- + ------ -------------- ------------ Network | None Exec | Radius Start-Stop System | Radius Stop-Only Commands | Radius Interim-Update
Common-CLI-Phase-3-Sept-2012.book Page 281 Sunday, September 9, 2012 6:00 PM
2-282
Display Commandsdisplay radius scheme
Minimum Software Version: 15.09.
Second Acct Server n/a
IP Server IP Address
Port Auth Port or Acct Port
State n/a
Encryption Key Encryption Key
VPN instance n/a
Auth Server Encryption Key n/a
Acct Server Encryption Key n/a
Accounting-On packet disable, send times
n/a
Interval for timeout (sec) Timeout (secs)
Retransmission times for timeout
n/a
Interval for realtime accounting (minute)
Interval(min)
Retransmission times of realtime-accounting packet
n/a
Retransmission times of stop-accounting packet
n/a
Quiet-interval(min) Deadtime (min)
Username format n/a
Data flow unit n/a
Packet unit n/a
NAS-IP address n/a
Attribute 25 n/a
n/a Retransmit Attempts
n/a Dynamic Authorization UDP Port
n/a Source IP Selection
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 282 Sunday, September 9, 2012 6:00 PM
2-283
Display Commandsdisplay rip
display rip
Displays RIP configuration information. The command provides information regarding the version, preference, cost, summary, maximum number of bal-anced paths, configured peers, number of route changes and number of replies to queries in a RIP route.
HP Switch# display rip Public VPN-instance name : n/a
RIP process : n/a RIP version : 1 Preference : 120 checkzero : n/a Default-cost : 1 Summary : Enabled Hostroutes : n/a Maximum number of balanced paths : 4 Update time : n/a Timeout time : n/a Suppress time : n/a Garbage-collect time : n/a Update output delay : n/a Output count : n/a TRIP retransmit time : n/a TRIP response packets retransmit count : n/a Silent interfaces : n/a Default routes : Disabled Verify-source : Enabled Networks : n/a Configured peers : None Triggered updates sent : 0 Number of route changes : 0 Number of replies to queries : 0
Minimum Software Version: 15.09.
Comware Related ProVision
display rip No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 283 Sunday, September 9, 2012 6:00 PM
2-284
Display Commandsdisplay rip interface
display rip interface
Displays RIP interface information of the RIP process. If no interface is specified, information about all RIP interfaces of the RIP process is displayed.
HP Switch# display rip 1 interface
Interface-name: Vlan-interface2 Address/Mask:2.2.2.2/24 Version:RIPv2 MetricIn:1 MetricIn route policy:n/a MetricOut:0 MetricOut route policy:n/a Split-horizon/Poison-reverse:on/on Input/Output:on/on Default route:on Current packets number/Maximum packets number:n/a
Interface-name: Vlan-interface3 Address/Mask:3.3.3.3/8 Version:RIPv1 MetricIn:1 MetricIn route policy:n/a MetricOut:0 MetricOut route policy:n/a Split-horizon/Poison-reverse:on/on Input/Output:on/on Default route:on Current packets number/Maximum packets number:n/a
Interface-name: Vlan-interface4 Address/Mask:192.168.4.55/16 Version:RIPv1 or RIPv2 MetricIn:1 MetricIn route policy:n/a MetricOut:0 MetricOut route policy:n/a Split-horizon/Poison-reverse:on/off Input/Output:on/on Default route:on Current packets number/Maximum packets number:n/a
HP Switch# display rip 1 interface vlan-interface 2
Interface-name: Vlan-interface2 Address/Mask:2.2.2.2/24 Version:RIPv2 MetricIn:1 MetricIn route policy:n/a MetricOut:0 MetricOut route policy:n/a Split-horizon/Poison-reverse:on/on Input/Output:on/on Default route:on Current packets number/Maximum packets number:n/a
Minimum Software Version: 15.10.
Comware Related ProVision
display rip interface No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 284 Sunday, September 9, 2012 6:00 PM
2-285
Display Commandsdisplay rip process-id ip-address mask/mask-length
display rip process-id ip-address mask/mask-length
Displays routes learnt by RIP. The command provides information regarding the peer address, vlan-interface (to which the peer is connected), route destination, route destination mask, route NextHop, route cost, route flags, route secs for all the routes that RIP has learnt.
HP Switch # display rip 1 route 20.0.0.0 8
Route Flags: R - RIP, T - TRIP P - Permanent, A - Aging, S - Suppressed, G - Garbage-collect------------------------------------------------------------- Peer 10.1.1.1 on Vlan-interface10
Destination/Mask Nexthop Cost Tag Flags Sec 20.0.0.0/8 10.1.1.1 1 0 RA 5
Minimum Software Version: 15.09.
Comware Related ProVision
display rip process-id ip-address mask/mask-length
No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 285 Sunday, September 9, 2012 6:00 PM
2-286
Display Commandsdisplay rip process-id route
display rip process-id route
HP Switch# display rip 1 route
Route Flags: R - RIP, T - TRIP
P - Permanent, A - Aging, S - Suppressed, G - Garbage-collect ------------------------------------------------------------- Peer 10.1.1.1 on Vlan-interface10 Destination/Mask Nexthop Cost Tag Flags Sec 5.0.0.0/8 10.1.1.1 2 0 RA 5 6.0.0.0/8 10.1.1.1 1 0 RA 5 20.0.0.0/8 10.1.1.1 1 0 RA 5
Minimum Software Version: 15.09.
Comware Related ProVision
display rip process-id route No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 286 Sunday, September 9, 2012 6:00 PM
2-287
Display Commandsdisplay rip process-id route peer ip-address
display rip process-id route peer ip-address
HP Switch# display rip 1 route peer 10.1.1.1
Route Flags: R - RIP, T - TRIP
P - Permanent, A - Aging, S - Suppressed, G - Garbage-collect ------------------------------------------------------------- Peer 10.1.1.1 on Vlan-interface10
Destination/Mask Nexthop Cost Tag Flags Sec 5.0.0.0/8 10.1.1.1 2 0 RA 5 6.0.0.0/8 10.1.1.1 1 0 RA 5 20.0.0.0/8 10.1.1.1 1 0 RA 5
Minimum Software Version: 15.09.
Comware Related ProVision
display rip process-id route peer ip-address No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 287 Sunday, September 9, 2012 6:00 PM
2-288
Display Commandsdisplay rmon statistics
display rmon statistics
Displays rmon statistics for the remote monitoring statistics information.HP Switch# display rmon statistics A1EtherStatsEntry 1 owned by monitor: is 1 Interface:A1 etherStatsOctets : 3724 , etherStatsPkts : 24 etherStatsBroadcastPkts : 4 , etherStatsMulticastPkts : 15 etherStatsUndersizePkts : 0 , etherStatsOversizePkts : 0 etherStatsFragments : 0 , etherStatsJabbers : 0 etherStatsCRCAlignErrors : 0 , etherStatsCollisions : 0 etherStatsDropEvents(insufficient resources) : 0 Packets received according to length: 64 : 12 , 65-127 : 0 , 128-255 : 8 256-511 : 4 , 512-1023 : 0 , 1024-1518 : 0
Operating Notes
For more information, refer to the latest Command Line Interface Reference
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display rmon statistics show rmon statistics
Common-CLI-Phase-3-Sept-2012.book Page 288 Sunday, September 9, 2012 6:00 PM
2-289
Display Commandsdisplay route-policy
display route-policy
Displays FIPS state. By default, the FIPS mode is disabled.
HP Switch# display route-policyRoute-Policy : qwer permit :10 if-match community abcd permit :11 if-match interface vlan 2 if-match ip-nexthop Prefix test if-match ipv6-route-source abcd if-match ipv6-address test if-match local-preference 32 if-match metric 44 if-match routetype external 2 if-match sourceprotocol static if-match tag 33 if-match community none if-match ip-nexthop 1.2.3.4 if-match ipv6-nexthop 2001:db8:85a3::8a2e:370:7334 if-match as-path test apply origin egpRoute-Policy : test permit :12 if-match community test deny :20 apply metric 3 apply tag 33 apply asPathPrepend apply weight 44
Example of Related ProVision Software Command Output.
HP Switch# show route-map Map3Routemap information
route-map "Map3" permit seq 10 match interface vlan 11 12 13 match metric 25 exitroute-map "Map3" permit seq 20
Comware Related ProVision
display route-policy show route-map
Common-CLI-Phase-3-Sept-2012.book Page 289 Sunday, September 9, 2012 6:00 PM
2-290
Display Commandsdisplay route-policy
match interface vlan 21 22 23 match metric 25exit
For more information, see the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 290 Sunday, September 9, 2012 6:00 PM
2-291
Display Commandsdisplay saved-configuration
display saved-configuration
Displays contents of the configuration file saved for the next startup of the switch.
HP Switch# display saved-configuration ; J8697A Configuration Editor; Created on release #K.15.09.0000x; Ver #03:01.1f.ef:f2hostname "HP-5406zl"module 1 type J9536Amodule 6 type J9534Asnmp-server community "public" Unrestrictedvlan 1 name "DEFAULT_VLAN" untagged A1-A22,F1-F24 ip address dhcp-bootp exit
Example of Related ProVision Software Command Output.
HP Switch# show configStartup configuration:; J8697A Configuration Editor; Created on release #K.14.01hostname "HP Switch"module 1 type J8705Asnmp-server community "public" Unrestrictedvlan 1 name "DEFAULT_VLAN" untagged A1-A24 ip address dhcp-bootp exitinterface A1 rate-limit all out kbps 200 exitinterface A2 rate-limit all out kbps 200 exitinterface A3 rate-limit all out kbps 200 exitinterface A4 rate-limit all out kbps 200
Comware Related ProVision
display saved-configuration show config
Common-CLI-Phase-3-Sept-2012.book Page 291 Sunday, September 9, 2012 6:00 PM
2-292
Display Commandsdisplay saved-configuration
exitinterface A5 rate-limit all in percent 200 exitinterface A6 rate-limit icmp percent 60 rate-limit mcast in percent 60 exit
For more information, see the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 292 Sunday, September 9, 2012 6:00 PM
2-293
Display Commandsdisplay saved-configuration by-linenum
display saved-configuration by-linenum
Displays the saved configuration of the switch with the line number. This command adds the line number to the output of display saved-configuration. This command is available only in manager mode.HP Switch# display saved-configuration by-linenum; J8692A Configuration Editor; Created on release #K.15.09.0000x; Ver #03:01.1f.ef:f2 1: hostname "HP-E3500yl-24G" 2: module 1 type J86xxA 3: snmp-server community "public" Unrestricted 4: vlan 1 5: name "DEFAULT_VLAN" 6: untagged 1-24 7: ip address dhcp-bootp 8: exit
Example of Related ProVision Software Command Output.
HP Switch# show configStartup configuration:; J8697A Configuration Editor; Created on release #K.14.01hostname "HP Switch"module 1 type J8705Asnmp-server community "public" Unrestrictedvlan 1name "DEFAULT_VLAN"untagged A1-A24ip address dhcp-bootpexitinterface A1rate-limit all out kbps 200exitinterface A2rate-limit all out kbps 200exitinterface A3rate-limit all out kbps 200exitinterface A4rate-limit all out kbps 200exitinterface A5rate-limit all in percent 200
Comware Related ProVision
display saved-configuration by-linenum show config
Common-CLI-Phase-3-Sept-2012.book Page 293 Sunday, September 9, 2012 6:00 PM
2-294
Display Commandsdisplay saved-configuration by-linenum
exitinterface A6rate-limit icmp percent 60rate-limit mcast in percent 60exit
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 294 Sunday, September 9, 2012 6:00 PM
2-295
Display Commandsdisplay schedule reboot
display schedule reboot
Displays the user-configured switch reboot (reload) time. For example, if the current date and time is March 21, 2012 at 1:05 PM (13:05), and the switch is configured to reboot (reload) at 5:00 PM (17:00) on the same date, then you would see the following output when executing this command:
HP Switch(config)# display schedule reboot System will reboot at 17:00 03/21/2012 (in 3 hours and 55 minutes).
Operating Notes
To configure a reboot time on the switch, use the following command:
[no] reload [ after | at ]
For more on using the reload command, refer to the “Switch Memory and Configuration” chapter in the latest Basic Operation Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show reload at
Reload scheduled for 17:00:52 02/21/2012 (in 0 days, 3 hours, 55 minutes)
Minimum Software Version: 15.08.
Comware Related ProVision
display schedule reboot show reload < after | at >
Common-CLI-Phase-3-Sept-2012.book Page 295 Sunday, September 9, 2012 6:00 PM
2-296
Display Commandsdisplay sflow display sflow slot <slot-number>
display sflow display sflow slot <slot-number>
Displays the sflowglobal, collector and port information.
HP Switch# display sflowsFlow Version: 1.3;HP;K.15.10.0000xsFlow Global Information:Agent IP:120.93.219.32(Auto)Collector Information:ID IP Port Aging Size Description1 1.2.3.4 1 2147483512 1400 n/a2 1.2.3.5 2 2147483525 1400 n/a3 1.2.3.6 3 2147483547 1400 n/asFlow Port Information:Interface CID Interval(s) FID MaxHLen Rate Mode StatusA4 1 0 1 128 51 Random InactiveA5 2 0 2 128 52 Random InactiveA6 3 0 3 128 53 Random InactiveC1 2 0 2 128 88 Random ActiveF10 1 0 1 128 77 Random Inactive
HP Switch# display sflow slot AsFlow Version: 1.3;HP;K.15.10.0000xsFlow Global Information:Agent IP:120.93.219.32(Auto)Collector Information:ID IP Port Aging Size Description1 1.2.3.4 1 2147483512 1400 n/a2 1.2.3.5 2 2147483525 1400 n/a3 1.2.3.6 3 2147483547 1400 n/asFlow Port Information:Interface CID Interval(s) FID MaxHLen Rate Mode StatusA4 1 0 1 128 51 Random InactiveA5 2 0 2 128 52 Random InactiveA6 3 0 3 128 53 Random Inactive
Comware Related ProVision
display sflowdisplay sflow slot <slot-number>
sh sflow agentsh sflow <receiver table number> sampling-polling
Common-CLI-Phase-3-Sept-2012.book Page 296 Sunday, September 9, 2012 6:00 PM
2-297
Display Commandsdisplay sflow display sflow slot <slot-number>
Example of Related ProVision Software Command Output.
HP Switch# sh sflow agent Version : 1.3;HP;K.15.10.0000x Agent Address : 120.93.219.32 Source IP Selection : Outgoing Interface
HP Switch# sh sflow 1 sampling-polling
Port | Sampling Dropped | Polling | Enabled Rate Header Samples | Enabled Interval----- + ------- -------- ------ ---------- + ------- --------A1 --- --- --- --- Yes(1) 21A4 Yes(1) 51 128 0 --- ---F10 Yes(1) 77 128 0 --- ---
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 297 Sunday, September 9, 2012 6:00 PM
2-298
Display Commandsdisplay snmp-agent community
display snmp-agent community
Displays community information for SNMPv1 or SNMPv2. This command is available only in manager mode.HP Switch# display snmp-agent community Community name: public Group name: n/a Storage-type: volatile
Example of Related ProVision Software Command Output.
HP Switch# show snmpv3 community
snmpCommunityTable [rfc2576]
Index Name Community Name Security Name---------- --------------- ------------------------1 public CommunityManagerReadWrite2 Operator CommunityOperatorReadOnly3 Manager CommunityManagerReadWrite30 Operator CommunityManagerReadWrite
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display snmp-agent community show snmpv3 community
Common-CLI-Phase-3-Sept-2012.book Page 298 Sunday, September 9, 2012 6:00 PM
2-299
Display Commandsdisplay snmp-agent group
display snmp-agent group
Displays information for the SNMPv3 agent group, including group name, security model, MIB view, and storage type. Absence of the group-name parameter indicates that information for all groups is displayed.HP Switch# display snmp-agent group Group name: ComManagerR Security model: v1 noAuthnoPriv Readview: ManagerReadView Writeview: DiscoverView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ComManagerR Security model: v2 noAuthnoPriv Readview: ManagerReadView Writeview: DiscoverView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ManagerAuth Security model: v3 AuthnoPriv Readview: ManagerReadView Writeview: ManagerWriteView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ManagerPriv Security model: v3 AuthPriv Readview: ManagerReadView Writeview: ManagerWriteView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ComManagerRW Security model: v1 noAuthnoPriv Readview: ManagerReadView Writeview: ManagerWriteView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ComManagerRW Security model: v2 noAuthnoPriv Readview: ManagerReadView Writeview: ManagerWriteView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ComOperatorR
Comware Related ProVision
display snmp-agent group show snmpv3 group
Common-CLI-Phase-3-Sept-2012.book Page 299 Sunday, September 9, 2012 6:00 PM
2-300
Display Commandsdisplay snmp-agent group
Security model: v1 noAuthnoPriv Readview: OperatorReadView Writeview: DiscoverView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: ComOperatorR Security model: v2 noAuthnoPriv Readview: OperatorReadView Writeview: DiscoverView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: OperatorAuth Security model: v3 AuthnoPriv Readview: OperatorReadView Writeview: DiscoverView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: ComOperatorRW Security model: v1 noAuthnoPriv Readview: OperatorReadView Writeview: OperatorReadView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: ComOperatorRW Security model: v2 noAuthnoPriv Readview: OperatorReadView Writeview: OperatorReadView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: OperatorNoAuth Security model: v3 noAuthnoPriv Readview: OperatorReadView Writeview: DiscoverView Notifyview: OperatorReadView Storage-type: ReadOnly
Common-CLI-Phase-3-Sept-2012.book Page 300 Sunday, September 9, 2012 6:00 PM
2-301
Display Commandsdisplay snmp-agent group
Example of Related ProVision Software Command Output.
HP Switch# show snmpv3 group
Status and Counters - SNHP v3 Global Configuration Information
Security Name Security Model Group Name------------------------ -------------- -----------------CommunityManagerReadOnly ver1 ComManagerRCommunityManagerReadWrite ver1 ComManagerRWCommunityOperatorReadOnly ver1 ComOperatorRWCommunityOperatorReadWrite ver1 ComOperatorRWCommunityManagerReadOnly ver2c ComManagerRCommunityManagerReadWrite ver2c ComManagerRWCommunityOperatorReadOnly ver2c ComOperatorRWCommunityOperatorReadWrite ver2c ComOperatorRWNetworkMgr ver3 ManagerPrivNetworkAdmin ver3 OperatorNoAuth
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 301 Sunday, September 9, 2012 6:00 PM
2-302
Display Commandsdisplay snmp-agent local-engineid
display snmp-agent local-engineid
Displays the SNMP agent local engine ID.
HP Switch# display snmp-agent local-engineid SNMP local EngineID: 0000000b0000001871c42f00
Field Descriptions
SNMP local EngineID: Identifies an SNMP entity uniquely within an SNMP domain.
Operating Notes
There is no specific user configuration command for SNMP agent local engine ID.
For more on switch SNMP operation, refer to the “Configuring for Network Management Applications” chapter in the latest Management and Configu-
ration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch# HP Switch# show snmpv3 engineid
Status and Counters - SNMP v3 EngineId Information
EngineId: 00:00:00:0b:00:00:00:18:71:c4:2f:00
snmp-agent local-engineid Field Mappings.
Minimum Software Version: 15.08.
Comware Related ProVision
display snmp-agent local-engineid show snmpv3 engineid
Comware ProVision Software
SNMP local EngineID EngineID
Common-CLI-Phase-3-Sept-2012.book Page 302 Sunday, September 9, 2012 6:00 PM
2-303
Display Commandsdisplay snmp-agent mib-view
display snmp-agent mib-view
Displays the View name, MIB Subtree, Subtree mask, Storage-type, View Type and View status. This command is available only in manager mode.HP Switch# display snmp-agent mib-view
View name: DiscoverView MIB Subtree: 1.3.6.1.6.3.15.1.2.2.1.7 Subtree mask: Storage-type: readOnly View Type: included View status: notInService Storage-type: readOnly
View name: DiscoverView MIB Subtree: 1.3.6.1.6.3.15.1.2.2.1.10 Subtree mask: Storage-type: readOnly View Type: included View status: notInService
Example of Related ProVision Software Command Output.
HP Switch# show snmpv3 group
Status and Counters - SNHP v3 Global Configuration Information
Security Name Security Model Group Name------------------------ -------------- -----------------CommunityManagerReadOnly ver1 ComManagerRCommunityManagerReadWrite ver1 ComManagerRWCommunityOperatorReadOnly ver1 ComOperatorRWCommunityOperatorReadWrite ver1 ComOperatorRWCommunityManagerReadOnly ver2c ComManagerRCommunityManagerReadWrite ver2c ComManagerRWCommunityOperatorReadOnly ver2c ComOperatorRWCommunityOperatorReadWrite ver2c ComOperatorRWNetworkMgr ver3 ManagerPrivNetworkAdmin ver3 OperatorNoAuth
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display snmp-agent mib-view show snmpv3 group
Common-CLI-Phase-3-Sept-2012.book Page 303 Sunday, September 9, 2012 6:00 PM
2-304
Display Commandsdisplay snmp-agent statistics
display snmp-agent statistics
Displays SNMP statistics, identifies SNMP PDUs, and provides information regarding the number of PDUs in request, reply, get, set, errors and MIB retrieval and altered state.HP Switch# display snmp-agent statistics 0 Messages delivered to the SNMP entity 0 Messages which were for an unsupported version 0 Messages which used a SNMP community name not known 0 Messages which represented an illegal operation for the community supplied 0 ASN.1 or BER errors in the process of decoding 0 Messages passed from the SNMP entity 0 SNMP PDUs which had badValue error-status 0 SNMP PDUs which had genErr error-status 0 SNMP PDUs which had noSuchName error-status 0 SNMP PDUs which had tooBig error-status (Maximum packet size 1500) 10 MIB objects retrieved successfully 1 MIB objects altered successfully 0 GetRequest-PDU accepted and processed 0 GetNextRequest-PDU accepted and processed 0 GetBulkRequest-PDU accepted and processed 0 GetResponse-PDU accepted and processed 0 SetRequest-PDU accepted and processed 0 Trap PDUs accepted and processed 0 Alternate Response Class PDUs dropped silently 0 Forwarded Confirmed Class PDUs dropped silently
Minimum Software Version: 15.10.
Comware Related ProVision
display snmp-agent statistics No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 304 Sunday, September 9, 2012 6:00 PM
2-305
Display Commandsdisplay snmp-agent sys-info
display snmp-agent sys-info
Displays current SNMP system information.HP Switch# display snmp-agent sys-infoThe contact person for this managed node: admin The physical location of this node: HP SNMP version running in the system: SNMPv1 SNMPv2c SNMPv3
Example of Related ProVision Software Command Output.
HP Switch# show system informationStatus and Counters - General System InformationSystem Name : HP SwitchSystem Contact :System Location :MAC Age Time (sec) : 300Time Zone : 0Daylight Time Rule : None
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display snmp-agent sys-info show system information
Common-CLI-Phase-3-Sept-2012.book Page 305 Sunday, September 9, 2012 6:00 PM
2-306
Display Commandsdisplay snmp-agent trap-list
display snmp-agent trap-list
Displays modules that can generate traps and whether or not their trap function is enabled. This command is available only in manager mode.HP Switch# display snmp-agent trap-list snmp Authentication trap extended password change trap enable login failures trap enable port security trap enable authorization server contact trap enable dhcp-snooping trap enable dynamic arp protection trap enable dynamic ip lockdown trap enable startup config change trap disable running config change trap disable mac address table changes trap disable mac address count trap disable
Enable traps: 8; Disable traps: 4
Example of Related ProVision Software Command Output.
HP Switch# show snmp-server traps
Trap Receivers
Link-Change Traps Enabled on Ports [All] : A1-A24
Traps Category Current Status-------------------------- ---------------SNMP Authentication : ExtendedPassword change : EnabledLogin failures : EnabledPort-Security : EnabledAuthorization Server Contact : EnabledDHCP Snooping : EnabledDynamic ARP Protection : EnabledDynamic IP Lockdown : Enabled
Address Community Events Sent Notify Type Retry Timeout----------------- ------- ----------- ----------- ----- ------- 15.255.5.225 public All trap 3 152001:0db8:0000:0001:0000:0000:0000:0121 user_1 All trap 3 15
Excluded MIBs
Comware Related ProVision
display snmp-agent trap-list show snmp-server traps
Common-CLI-Phase-3-Sept-2012.book Page 306 Sunday, September 9, 2012 6:00 PM
2-307
Display Commandsdisplay snmp-agent trap-list
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 307 Sunday, September 9, 2012 6:00 PM
2-308
Display Commandsdisplay snmp-agent usm-user
display snmp-agent usm-user
Displays the snmp users configured in the system. This command is available only in manager mode.HP Switch# display snmp-agent usm-user
User name: user Group name: ComOperatorR Engine ID: 0000000B00000019BBBACD00 Storage-type: nonVolatile UserStatus: active
User name: initial Group name: ManagerPriv Engine ID: 0000000B00000019BBBACD00 Storage-type: nonVolatile UserStatus: active
Example of Related ProVision Software Command Output.
HP Switch# show snmpv3 userStatus and Counters - SNMP v3 Global Configuration InformationUser Name Auth. Protocol Privacy Protocol------------ -------------- ----------------initial MD5 CFB AES-128NetworkAdmin MD5 CBC-DES
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display snmp-agent usm-user show snmpv3 user
Common-CLI-Phase-3-Sept-2012.book Page 308 Sunday, September 9, 2012 6:00 PM
2-309
Display Commandsdisplay ssh client source
display ssh client source
Displays the source IP address or source interface currently set for the SSH client. If neither source IP address nor source interface is specified for the SSH client, the system will prompt you to specify the source information.
HP Switch# display ssh client source
Neither source IP address nor source interface was specified for the STelnet client.
Minimum Software Version: 15.09.
Comware Related ProVision
display ssh client source No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 309 Sunday, September 9, 2012 6:00 PM
2-310
Display Commandsdisplay ssh server session
display ssh server session
Displays SSH server session information. This command is available only in manager mode.HP Switch# display ssh server session
Conn Ver Encry State Retry SerType UsernameA1 2.0 AES Established n/a Stelnet manager
Example of Related ProVision Software Command Output.
HP Switch# show ip sshSSH Enabled : Yes Secure Copy Enabled : NoTCP Port Number : 22 Timeout (sec) : 120Host Key Type : RSA Host Key Size : 2048
Ciphers : aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc, [email protected],aes128-ctr,aes192-ctr,aes256-ctr
MACs : hmac-md5,hmac-sha1,hmac-sha1-96,hmac-md5-96
Ses Type | Source IP Port--- -------- + -------------- -------1 console |2 telnet |3 ssh | 15.30.252.195 15314 inactive |5 inactive |6 inactive |
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display ssh server session show ip ssh
Common-CLI-Phase-3-Sept-2012.book Page 310 Sunday, September 9, 2012 6:00 PM
2-311
Display Commandsdisplay ssh server-info
display ssh server-info
Displays mappings between SSH servers and their host public keys saved on the client.HP Switch# display ssh server-infoServer Name(IP) Server public key name---------------- -----------------------120.85.212.127 n/a
Minimum Software Version: 15.10.
Comware Related ProVision
display ssh server-info No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 311 Sunday, September 9, 2012 6:00 PM
2-312
Display Commandsdisplay ssh server status
display ssh server status
Displays the SSH server status information or session information.
HP Switch# display ssh server status
SSH server : enabled SSH version : 2 SSH authentication-timeout : 120 second(s) SSH server key generating interval : n/a SSH authentication retries : 3 time(s) SFTP server : disabled SFTP server Idle-Timeout : 0 minutes(s)
Field Descriptions:
SSH server: Whether the SSH server function is enabled
SSH version: SSH protocol version. When the SSH supports SSH1, the protocol version is 1.99. Otherwise, the protocol version is 2.0.
SSH authentication-timeout: Authentication timeout period
SSH server key generating interval: SSH server key pair update interval
SSH authentication retries: Maximum number of SSH authentication attempts
SFTP server: Whether the SFTP server function is enabled
SFTP server Idle-Timeout: SFTP connection idle timeout period
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip ssh
SSH Enabled : Yes Secure Copy Enabled : No TCP Port Number : 22 Timeout (sec) : 120 Host Key Type : RSA Host Key Size : 2048
Ciphers : aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc,
[email protected],aes128-ctr,aes192-ctr,aes256-ctr
Comware Related ProVision
display ssh server status show ip ssh
Common-CLI-Phase-3-Sept-2012.book Page 312 Sunday, September 9, 2012 6:00 PM
2-313
Display Commandsdisplay ssh server status
MACs : hmac-md5,hmac-sha1,hmac-sha1-96,hmac-md5-96
Ses Type | Source IP Port ---- --------+ ---------- ----- 1 console |2 telnet |3 ssh | 15.30.252.195 15314 inactive |5 inactive |6 inactive |
For more information, see the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 313 Sunday, September 9, 2012 6:00 PM
2-314
Display Commandsdisplay ssl client-policy
display ssl client-policy
Displays information about all SSL client policies. This command is available only in manager mode.HP Switch# display ssl client-policySSL Client Policy: n/a SSL Version: TLS 1.0 PKI Domain: n/a Prefer Ciphersuite: aes256-ctr aes256-cbc [email protected] aes192-ctr aes192-cbc aes128-ctr aes128-cbc 3des-cbc hmac-sha1-96 hmac-md5 hmac-sha1 hmac-md5-96 aes192-ctr aes192-cbc aes128-ctr aes128-cbc 3des-cbc Server-verify: n/aTotal 1 SSL client policy(s).
Example of Related ProVision Software Command Output.
HP Switch# show ip sshSSH Enabled : Yes Secure Copy Enabled : NoTCP Port Number : 22 Timeout (sec) : 120Host Key Type : RSA Host Key Size : 2048
Ciphers : aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc, [email protected],aes128-ctr,aes192-ctr,aes256-ctr
MACs : hmac-md5,hmac-sha1,hmac-sha1-96,hmac-md5-96
Ses Type | Source IP Port--- -------- + -------------- -------1 console |2 telnet |3 ssh | 15.30.252.195 15314 inactive |5 inactive |
Comware Related ProVision
display ssl client-policy show ip ssh
Common-CLI-Phase-3-Sept-2012.book Page 314 Sunday, September 9, 2012 6:00 PM
2-315
Display Commandsdisplay ssl client-policy
6 inactive |
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 315 Sunday, September 9, 2012 6:00 PM
2-316
Display Commandsdisplay ssl server-policy
display ssl server-policy
Displays information about all SSL client policies. This command is available only in manager mode.HP Switch# display ssl server-policySSL Server Policy: n/a PKI Domain: n/a Ciphersuite: aes256-ctr aes256-cbc [email protected] aes192-ctr aes192-cbc aes128-ctr aes128-cbc 3des-cbc hmac-sha1-96 hmac-md5 hmac-sha1 hmac-md5-96 aes192-ctr aes192-cbc aes128-ctr aes128-cbc 3des-cbc Handshake Timeout: 120 Close-mode: n/a Session Timeout: n/a Session Cachesize: n/a Client-verify: n/a Client-verify weaken: n/a
Total 1 SSL server policy(s).
Comware Related ProVision
display ssl server-policy show ip ssh
Common-CLI-Phase-3-Sept-2012.book Page 316 Sunday, September 9, 2012 6:00 PM
2-317
Display Commandsdisplay ssl server-policy
Example of Related ProVision Software Command Output.
HP Switch# show ip sshSSH Enabled : Yes Secure Copy Enabled : NoTCP Port Number : 22 Timeout (sec) : 120Host Key Type : RSA Host Key Size : 2048
Ciphers : aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc, [email protected],aes128-ctr,aes192-ctr,aes256-ctr
MACs : hmac-md5,hmac-sha1,hmac-sha1-96,hmac-md5-96
Ses Type | Source IP Port--- -------- + -------------- -------1 console |2 telnet |3 ssh | 15.30.252.195 15314 inactive |5 inactive |6 inactive |
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 317 Sunday, September 9, 2012 6:00 PM
2-318
Display Commandsdisplay startup
display startup
Displays the configuration file used at the current system startup and the configuration file(s) to be used at the next system startup.
HP Switch# display startup
Current startup saved-configuration file: flash:/svt-1.cfg
Next startup saved-configuration file for primary image: flash:/svt-1.cfg
Next startup saved-configuration file for secondary image: flash:/svt-2.cfg
Minimum Software Version: 15.10.
Comware Related ProVision
display startup No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 318 Sunday, September 9, 2012 6:00 PM
2-319
Display Commandsdisplay stp
display stp
Displays the MSTP status and statistics. Based on the MSTP status and statistics, you can analyze and maintain the network topology or check whether MSTP is working normally.
Spanning-tree protocol is enabled
HP Switch# display stp -------[CIST Global Info][Mode STP]------- CIST Bridge :32768.3ce5-a674-b433 Bridge Times :Hello 2s MaxAge 20s FwDly 15s MaxHop 20 CIST Root/ERPC :32768.3ce5-a674-b433 / 0 CIST RegRoot/IRPC :32768.3ce5-a674-b433 / 0 CIST RootPortId :0.0 BPDU-Protection :disabled Bridge Config- Digest-Snooping :disabled TC or TCN received :0 Time since last TC :1 days 22h:48m:24s
----[PortA1(A1)][DOWN]---- Port Protocol :0 Port Role :CIST Disabled Port Port Priority :128 Port Cost(Legacy) :0 Desg. Bridge/Port :32768.3ce5-a674-b433 / 128.1 Port Edged :Config=disabled / Active=disabled Point-to-point :Config=auto / Active=false Transmit Limit :10 packets/hello-time Protection Type :None MST BPDU Format :0 Port Config- Digest-Snooping :0 Num of Vlans Mapped :1 PortTimes :Hello 2s MaxAge 20s FwDly 15s MsgAge 0s RemHop 20 BPDU Sent :0 TCN: 0, Config: 0, RST: 0, MST: 0 BPDU Received :0 TCN: 0, Config: 0, RST: 0, MST: 0
Comware Related ProVision
display stp show spanning-tree
Common-CLI-Phase-3-Sept-2012.book Page 319 Sunday, September 9, 2012 6:00 PM
2-320
Display Commandsdisplay stp
----[PortA2(A2)][DOWN]---- . . . ----[PortA3(A3)][DOWN]---- . . . .
Example of Related ProVision Software Command Output.
HP Switch# show spanning-treeMultiple Spanning Tree (MST) InformationSTP Enabled : YesForce Version : MSTP-operationIST Mapped VLANs : 1-4094Switch MAC Address : 0024a8-d13a40Switch Priority : 32768Max Age : 20Max Hops : 20Forward Delay : 15Topology Change Count : 1Time Since Last Change : 20 minsCST Root MAC Address : 001083-847000CST Root Priority : 0CST Root Path Cost : 60000CST Root Port : 1IST Regional Root MAC Address : 0024a8-d13a40IST Regional Root Priority : 32768IST Regional Root Path Cost : 0IST Remaining Hops : 20Root Guard Ports :Loop Guard Ports : 2TCN Guard Ports :BPDU Protected Ports :BPDU Filtered Ports :PVST Protected Ports :PVST Filtered Ports : Prio | Designated HelloPort Type | Cost rity State | Bridge Time PtP Edge---- ----- ----- ----- ------ ----------- ---- --- -----1 100/1000T | 20000 128 Forwarding |001871-cdea00 2 Yes No2 100/1000T | Auto 128 Inconsistent |3 100/1000T | Auto 128 Disabled |4 100/1000T | Auto 128 Disabled |5 100/1000T | Auto 128 Disabled |6 100/1000T | Auto 128 Disabled |7 100/1000T | Auto 128 Disabled |8 100/1000T | Auto 128 Disabled |
Common-CLI-Phase-3-Sept-2012.book Page 320 Sunday, September 9, 2012 6:00 PM
2-321
Display Commandsdisplay stp
Comware supports instances ranging from 0-31 and ProVision supports instances ranging from 0-16. For more information, see the latest Advanced
Traffic Management Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 321 Sunday, September 9, 2012 6:00 PM
2-322
Display Commandsdisplay stp abnormal-port
display stp abnormal-port
Displays information about ports blocked by spanning tree protection func-tions.
HP Switch# display stp abnormal-portMSTID Blocked Port Reason1 A1 ROOT-Protected2 A2 LOOP-Protected
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree detailStatus and Counters - CST Port(s) Detailed InformationPort : 1Status : Up...Port : 2Status : UpBPDU Protection : NoBPDU Filtering : NoPVST Protection : NoPVST Filtering : NoErrant BPDU Count : 0Root Guard : NoLoop Guard : YesTCN Guard : NoMST Region Boundary : YesExternal Path Cost : 20000External Root Path Cost : 40000Administrative Hello Time : GlobalOperational Hello Time : 2AdminEdgePort : NoAuto Edge Port : YesOperEdgePort : NoAdminPointToPointMAC : TrueOperPointToPointMAC : YesAged BPDUs Count : 0Loop-back BPDUs Count : 0
Comware Related ProVision
display stp abnormal-port show spanning-tree detail show spanning-tree <port> detail
Common-CLI-Phase-3-Sept-2012.book Page 322 Sunday, September 9, 2012 6:00 PM
2-323
Display Commandsdisplay stp abnormal-port
TC ACK Flag Transmitted : 0TC ACK Flag Received : 1MST MST CFG CFG TCN TCNBPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx-------- -------- -------- -------- -------- --------- 3 0 24354 1682 0 13
For more information, see the latest Advanced Traffic Management Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 323 Sunday, September 9, 2012 6:00 PM
2-324
Display Commandsdisplay stp bpdu-statistics display stp bpdu-statistics interface GigabitEthernet <port-num> display stp bpdu-statistics
display stp bpdu-statistics display stp bpdu-statistics interface GigabitEthernet <port-num> display stp bpdu-statistics interface GigabitEthernet <port-num> instance <instanceNUM, 1-32>
Displays the debug counters of the STP in different modes.
In MSTP mode :
• If MSTI or port is not specified, this command displays the BPDU statistics of all MSTIs on all ports. The displayed information is sorted by port name and by MSTI ID on each port.
• If a port is specified but not an MSTI, this command displays the BPDU statistics of all MSTIs on the port. The displayed information is sorted by MSTI ID.
• If both an MSTI ID and a port are specified, this command displays the BPDU statistics of the specified MSTI on the port.
In STP, RSTP, or PVST mode:
• If no port is specified, this command displays the BPDU statistics of on all ports. The displayed information is sorted by port name.
• If a port is specified, this command displays the BPDU statistics on the port.
HP Switch# stp bpdu-statistics interface 2 instance 2
Port: 2 Instance-independent:
Comware Related ProVision
display stp bpdu-statisticsdisplay stp bpdu-statistics interface GigabitEthernet <port-num>display stp bpdu-statistics interface GigabitEthernet <port-num> instance <instanceNUM, 1-32>
show spanning-tree detail
Common-CLI-Phase-3-Sept-2012.book Page 324 Sunday, September 9, 2012 6:00 PM
2-325
Display Commandsdisplay stp bpdu-statistics display stp bpdu-statistics interface GigabitEthernet <port-num> display stp bpdu-statistics
Type Count Last Updated --------------------------- ---------- -----------------
Invalid BPDUs 0 Looped-back BPDUs 0 MAX-aged BPDUs 0 TCN sent 0 TCN received 0 TCA sent 0 TCA received 0 Config sent 0 Config received 0 RST sent 0 RST received 0 MST sent 0 MST received 0
Instance 2:
Type Count Last Updated
--------------------------- ---------- ----------------- Timeout BPDUs 0 MAX-hoped BPDUs 0 TC detected 0 TC sent 0 TC received 0
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree detailStatus and Counters - CST Port(s) Detailed InformationPort : 1Status : Up...Port : 2Status : UpBPDU Protection : NoBPDU Filtering : NoPVST Protection : NoPVST Filtering : NoErrant BPDU Count : 0Root Guard : NoLoop Guard : YesTCN Guard : NoMST Region Boundary : YesExternal Path Cost : 20000External Root Path Cost : 40000
Common-CLI-Phase-3-Sept-2012.book Page 325 Sunday, September 9, 2012 6:00 PM
2-326
Display Commandsdisplay stp bpdu-statistics display stp bpdu-statistics interface GigabitEthernet <port-num> display stp bpdu-statistics
Administrative Hello Time : GlobalOperational Hello Time : 2AdminEdgePort : NoAuto Edge Port : YesOperEdgePort : NoAdminPointToPointMAC : TrueOperPointToPointMAC : YesAged BPDUs Count : 0Loop-back BPDUs Count : 0TC ACK Flag Transmitted : 0TC ACK Flag Received : 1MST MST CFG CFG TCN TCNBPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx-------- -------- -------- -------- -------- --------- 3 0 24354 1682 0 13
For more information, see the latest Advanced Traffic Management Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 326 Sunday, September 9, 2012 6:00 PM
2-327
Display Commandsdisplay stp brief display stp instance <instance-id> brief display stp instance <instance-id> interface GigabitEthernet
display stp brief display stp instance <instance-id> brief display stp instance <instance-id> interface GigabitEthernet <interface-id> brief display stp instance <instance-id> interface GigabitEthernet <interface-id> brief display stp instance <instance-id> interface GigabitEthernet <interface-id> to GigabitEthernet <interface-id> brief display stp instance <instance-id> slot <slot-id> brief display stp interface GigabitEnterface <port-num> brief display stp interface GigabitEnterface <port-num> to GigabitEnterface <port-num> brief
Displays brief information about spanning tree status and statistics.
Spanning-tree protocol is enabledHP Switch# display stp brief MSTID Port Role STP State Protection 1 1 Designated Blocking No 2 2 Disabled Disabled No
Comware Related ProVision
display stp briefdisplay stp instance <instance-id> briefdisplay stp instance <instance-id> interface GigabitEthernet <interface-id> briefdisplay stp instance <instance-id> interface GigabitEthernet <interface-id> briefdisplay stp instance <instance-id> interface GigabitEthernet <interface-id> to GigabitEthernet <interface-id> briefdisplay stp instance <instance-id> slot <slot-id> briefdisplay stp interface gigabitEnterface <port-num> briefdisplay stp interface GigabitEnterface <port-num> to GigabitEnterface <port-num> brief
show spanning-tree configshow spanning-tree <PORT-LIST> detail
Common-CLI-Phase-3-Sept-2012.book Page 327 Sunday, September 9, 2012 6:00 PM
2-328
Display Commandsdisplay stp brief display stp instance <instance-id> brief display stp instance <instance-id> interface GigabitEthernet
Spanning-tree protocol is disabledHP Switch# display stp briefProtocol Status :disabledProtocol Std. :IEEE 802.1sVersion :0Bridge-Prio. :32768MAC address :000fe2-008048Max age(s) :20Forward delay(s) :15Hello time(s) :2Max hops :20
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree configMultiple Spanning Tree (MST) Configuration InformationSTP Enabled [No] : YesForce Version [MSTP-operation] : MSTP-operationDefault Path Costs [802.1t] : 802.1tMST Configuration Name : 1cc1decfbc80MST Configuration Revision : 0 Switch Priority : 32768Forward Delay [15] : 15 Hello Time [2] : 2Max Age [20] : 20 Max Hops [20] : 20 | Path Prio Admin Auto Admin Hello Root TCN BPDUPort Type | Cost rity Edge Edge PtP Time Grd Grd Flt---- ---- + ---- ---- ---- ----- ---- ----- ---- ---- --- 1 10/100TX | Auto 128 No Yes True Global No No No2 10/100TX | Auto 128 No Yes True Global No No No3 10/100TX | Auto 128 No Yes True Global No No No. . . . . . . . . . .7 10/100TX | Auto 128 No Yes True Global No No No
ProVision accepts interface range as 1-8. Comware accpets interface range as "GigabitEthernet1/0/1 to GigabitEthernet1/0/8".
CIST RootPortId and MSTI RootPortId are represented differently in ProVi-sion and Comware.
For more information, see the latest Advanced Traffic Management Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 328 Sunday, September 9, 2012 6:00 PM
2-329
Display Commandsdisplay stp down-port
display stp down-port
Displays information about ports shut down by spanning tree protection functions.
HP Switch# display stp down-port Down Port Reason 4 BPDU-Protected 5 BPDU-Protected
Operating Notes
ProVision does not support Format-Frequency.
Minimum Software Version: 15.09.
Comware Related ProVision
display stp down-port No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 329 Sunday, September 9, 2012 6:00 PM
2-330
Display Commandsdisplay stp history display stp history slot <slot-number> display stp instance <instance-id> history slot <slot-no> display
display stp history display stp history slot <slot-number> display stp instance <instance-id> history slot <slot-no> display stp instance <instance-id> history
display stp history displays the historical port role calculation information of all MSTIs.
display stp history slot slot-number displays the statistics of the port’s history information of all the MSTIs of a given slot when stp protocol is enabled.
display stp instance instance-id history displays the historical port role information of the specified MSTI when stp protocol is enabled.
display stp instance instance-id history slot slot-number displays the statistics of the port’s history information of the specified MSTI of a given slot when stp protocol is enabled.
HP Switch# display stp history
display stp history
--------------- STP slot 1 history trace ---------------
------------------- Instance 0 -------------------
Port 1 Role change :Disa->Desi Time :2012/05/28 09:47:23 Port priority :32768.002347-b4cb80 0 32768.002347-b4cb80 0 32768.002347-b4cb80 128.1
------------------- Instance 1 -------------------
Port 1 Role change :Disa->Desi Time :2012/05/28 09:47:23 Port priority :32768.002347-b4cb80 0 32768.002347-b4cb80 48.1
Comware Related ProVision
display stp history No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 330 Sunday, September 9, 2012 6:00 PM
2-331
Display Commandsdisplay stp history display stp history slot <slot-number> display stp instance <instance-id> history slot <slot-no> display
HP Switch# display stp history slot A
--------------- STP slot 1 history trace ---------------
------------------- Instance 0 -------------------
Port 1 Role change :Disa->Desi Time :2012/05/28 09:47:23 Port priority :32768.002347-b4cb80 0 32768.002347-b4cb80 0 32768.002347-b4cb80 128.1
------------------- Instance 1 -------------------
Port 1 Role change :Disa->Desi Time :2012/05/28 09:47:23 Port priority :32768.002347-b4cb80 0 32768.002347-b4cb80 48.1
HP Switch# display stp instance 0 history
--------------- STP slot 1 history trace ---------------
------------------- Instance 0 -------------------
Port 1 Role change :Disa->Desi Time :2012/05/28 09:47:23 Port priority :32768.002347-b4cb80 0 32768.002347-b4cb80 0 32768.002347-b4cb80 128.1
Minimum Software Version: 15.10.
Common-CLI-Phase-3-Sept-2012.book Page 331 Sunday, September 9, 2012 6:00 PM
2-332
Display Commandsdisplay stp
display stpdisplay stp instance <instance-id> interface GigabitEthernet 1/0/1/display stp slot <slot-num>
Displays MSTP status and statistics.
HP Switch# display stpProtocol Status : Disabled Protocol Std. : IEEE802.1s Version : 3 CIST Bridge-Prio : 32768 MAC Address : 0021f7-06ab00 Max age (s) : 2000 Forward delay (s) : 1500 Hello Time(s) : 200 Max Hops : 20
Example of Related ProVision Software Command Output.
HP Switch# show spanning-treeMultiple Spanning Tree (MST) InformationSTP Enabled : YesForce Version : MSTP-operationIST Mapped VLANs : 1-4094Switch MAC Address : 0024a8-d13a40Switch Priority : 32768Max Age : 20Max Hops : 20Forward Delay : 15Topology Change Count : 1Time Since Last Change : 20 minsCST Root MAC Address : 001083-847000CST Root Priority : 0CST Root Path Cost : 60000CST Root Port : 1IST Regional Root MAC Address : 0024a8-d13a40IST Regional Root Priority : 32768
Comware Related ProVision
display stpdisplay stp instance <instance-id> interface GigabitEthernet 1/0/1/display stp slot <slot-num>
show spanning-tree
Common-CLI-Phase-3-Sept-2012.book Page 332 Sunday, September 9, 2012 6:00 PM
2-333
Display Commandsdisplay stp slot <slot-num>
IST Regional Root Path Cost : 0IST Remaining Hops : 20Root Guard Ports :Loop Guard Ports : 2TCN Guard Ports :BPDU Protected Ports :BPDU Filtered Ports :PVST Protected Ports :PVST Filtered Ports : Prio | Designated HelloPort Type | Cost rity State | Bridge Time PtP Edge---- ----- ----- ----- ------ ----------- ---- --- -----1 100/1000T | 20000 128 Forwarding |001871-cdea00 2 Yes No2 100/1000T | Auto 128 Inconsistent |3 100/1000T | Auto 128 Disabled |4 100/1000T | Auto 128 Disabled |5 100/1000T | Auto 128 Disabled |6 100/1000T | Auto 128 Disabled |7 100/1000T | Auto 128 Disabled |8 100/1000T | Auto 128 Disabled |
For more information, see the latest Advanced Traffic Management Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 333 Sunday, September 9, 2012 6:00 PM
2-334
Display Commandsdisplay stp instance <instanceid> tc display stp instance <instanceid> tc slot <slot-no> display stp tc
display stp instance <instanceid> tc display stp instance <instanceid> tc slot <slot-no> display stp tc
Displays the STP information of a port under a particular instance when STP is enabled.
HP Switch# display stp instance 0 tc
-------------- STP slot A TC or TCN count ------------- MSTID Port Receive Send 0 A1 2 2
-------------- STP slot B TC or TCN count ------------- MSTID Port Receive Send
-------------- STP slot C TC or TCN count ------------- MSTID Port Receive Send
HP Switch# display stp instance 1 tc slot A
-------------- STP slot A TC or TCN count ------------- MSTID Port Receive Send 1 A2 0 2
HP Switch# display stp tc slot B-------------- STP slot B TC or TCN count ------------- MSTID Port Receive Send 0 B1 2 2 1 B2 0 2
Minimum Software Version: 15.09.
Comware Related ProVision
display stp instance <instanceid> tcdisplay stp instance <instanceid> tc slot <slot-no>display stp tc
No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 334 Sunday, September 9, 2012 6:00 PM
2-335
Display Commandsdisplay stp region-configuration
display stp region-configuration
Displays effective configuration information of the MST region, including the region name, revision level, and user-configured VLAN-to-instance mappings. Related commands: instance, region-name, revision-level, and vlan-mapping modulo.
Spanning-tree protocol is enabledHP Switch# display stp region-configurationOper ConfigurationFormat selector :0Region name :helloRevision level :0Configuration digest :0x5f762d9a46311effb7a488a3267fca9fInstance Vlans Mapped0 21 to 40941 1 to 102 11 to 20
Spanning-tree protocol is diabledHP Switch# display stp region-configurationOper configuration Format selector :0 Region name :3ce5a6761a00 Revision level :0 Configuration digest :
Instance Vlans Mapped 1 1 to 4094
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree mst-configMST Configuration Identifier InformationMST Configuration Name : 1cc1decfbc80MST Configuration Revision : 0MST Configuration Digest : 0xC8DB46AEBEA5F48799BD2D8B0E1BCA54IST Mapped VLANs : 1-110,112-299,301-4094Instance ID Mapped VLANs----------- -------------------------------------------------11 111,300
Comware Related ProVision
display stp region-configuration show spanning-tree mst-config
Common-CLI-Phase-3-Sept-2012.book Page 335 Sunday, September 9, 2012 6:00 PM
2-336
Display Commandsdisplay stp region-configuration
For more information, see the latest Advanced Traffic Management Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 336 Sunday, September 9, 2012 6:00 PM
2-337
Display Commandsdisplay stp root
display stp root
Displays the root bridge information of all MSTIs.
Spanning-tree protocol is enabledHP Switch# display stp rootMSTID Root Bridge ID ExtPathCost IntPathCost Root Port0 00e0fc-0e6554 200200 0 A1
Spanning-tree protocol is disabledHP Switch# display stp rootHP Switch#
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree instance 11MST Instance InformationInstance ID : 11Mapped VLANs : 111,300Switch Priority : 32768Topology Change Count : 2Time Since Last Change : 4 minsRegional Root MAC Address : 1cc1de-cfbc80Regional Root Priority : 32768Regional Root Path Cost : 400000Regional Root Port : This switch is rootRemaining Hops : 20DesignatedPort Type Cost Priority Role State Bridge---- ----- ---- --------- -------- ------ ---------1 10/100TX 200000 128 Root Forwarding 1cc1de-cfbc802 10/100TX 200000 128 Designated Forwarding 1cc1de-02a7003 10/100TX Auto 112 Designated Forwarding 1cc1de-02a7004 10/100TX Auto 128 Disabled Disabled
For more information, see the latest Advanced Traffic Management Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display stp root show spanning-tree instance <instance-id>show spanning-tree detail
Common-CLI-Phase-3-Sept-2012.book Page 337 Sunday, September 9, 2012 6:00 PM
2-338
Display Commandsdisplay switchover state
display switchover state
Displays the backup state of the specified main board. This command displays the backup state on the AMB or the standby main board (SMB) depending on the slot number specified. The backup state of the AMB is displayed if no slot number is specified.
Field Descriptions
Master HA State to Slot: Backup state between the active main board (AMB) and the standby main board (SMB).
Slave HA State: Indicates that the output information is generated by the SMB and describes the switchover state of the SMB.
Operating Notes
In Comware, either 0 or 1 displays for the slot, depending on which board is active (master or slave).
For more information about redundancy, see the “Chassis Redundancy (8200zl Switches)” chapter in the latest Management and Configuration Guide for your switch.
Comware Related ProVision
display switchover state show redundancy
HP Switch-8200# display switchover stateMaster HA state to slot [0] : Relative backup to slave
HP Switch-8200# display switchover state slot 0Slave HA State: Receiving realtime data
HP Switch-8200# display switchover state slot 1Master HA State to Slot [0]: Relative backup to slave
HP Switch-3800# display switchover stateComware: The corresponding ProVision command is "show redundancy".
Common-CLI-Phase-3-Sept-2012.book Page 338 Sunday, September 9, 2012 6:00 PM
2-339
Display Commandsdisplay switchover state
Example of Related ProVision Software Command Output.
display switchover state Field Mappings.
Minimum Software Version: 15.09.
HP Switch(config)# show redundancy
Settings--------Mgmt Redundancy : Nonstop switching enabledRapid Switchover Stale Timer : 0
Statistics----------Failovers : 0Last Failover :
Slot Module Description Status SW Version Boot Image---- ---------------------------------------- -------- ------------ ----------MM1 HP J9092A Management Module 8200zl Active K.15.01.000x PrimaryMM2 HP J9092A Management Module 8200zl Standby K.15.01.000x Primary
FM1 HP J9093A Fabric Module 8200zl EnabledFM2 HP J9093A Fabric Module 8200zl Enabled
Comware ProVision Software
Master HA State to Slot Status
Slave HA State Status
Common-CLI-Phase-3-Sept-2012.book Page 339 Sunday, September 9, 2012 6:00 PM
2-340
Display Commandsdisplay system-failure
display system-failure
HP Switch# display system-failure
System failure handling method: reboot
Example of Related ProVision Software Command Output.
HP Switch# show boot-history
Mgmt Module 1 -- Saved Crash Information (most recent first):=============================================================Mgmt Module 1 in Active Mode went down: 11/07/09 14:48:36Operator warm reload from CONSOLE session.Mgmt Module 1 in Active Mode went down: 11/07/09 11:43:10Operator cold reboot from CONSOLE session.
Mgmt Module 2 -- Saved Crash Information (most recent first):=============================================================No Saved Crash Information
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display system-failure show boot-history
Common-CLI-Phase-3-Sept-2012.book Page 340 Sunday, September 9, 2012 6:00 PM
2-341
Display Commandsdisplay this
display this
Displays valid configuration information under the current view. Use this command to check whether your configuration has taken effect. Valid config-uration that is the same as the default is not displayed. Invalid configuration is not displayed. Execution of this command in any user interface view displays the valid configuration in all the user interfaces. Execution of this command in any VLAN view displays the configurations of all the created VLANs.
HP Switch# display this
vlan 1 name "DEFAULT_VLAN" no untagged 1-2,48 untagged 3-47 ip address dhcp-bootp exit
vlan 10 name "VLAN10" untagged 1,48 ip address 10.10.10.3 255.255.255.0 ip igmp exit
vlan 30 name "VLAN30" untagged 2 ip address 30.30.30.2 255.255.255.0 ip igmp ip rip 30.30.30.2 ip pim-sparse ip-addr any exit
exit
Minimum Software Version: 15.10.
Comware Related ProVision
display this No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 341 Sunday, September 9, 2012 6:00 PM
2-342
Display Commandsdisplay transceiver alarm interface
display transceiver alarm interface
Displays the current alarm information of a single or all transceivers.
Field Descriptions
RX loss of signal: Incoming (RX) signal is lost.
TX fault: Transmit (TX) fault
RX power high: Incoming (RX) power level is high.
RX power low: Incoming (RX) power level is low.
TX power high: TX power is high.
TX power low: TX power is low.
TX bias low: TX bias current is low. TX bias high: TX bias current is high.
Temp high: Temperature is high.
Temp low: Temperature is low.
Voltage high: Voltage is high.
Voltage low: Voltage is low.
Transceiver info I/O error: Transceiver information read and write error
Transceiver info checksum error: Transceiver information checksum error
Transceiver type and port configuration mismatch: Transceiver type does not match port configuration.
Transceiver type not supported by port hardware: Transceiver type is not sup-ported on the port.
Comware Related ProVision
display transceiver alarm interface show interface transceiver detail
HP Switch(config)# display transceiver alarm interface g1G1 transceiver current alarm information: Rx power low
Common-CLI-Phase-3-Sept-2012.book Page 342 Sunday, September 9, 2012 6:00 PM
2-343
Display Commandsdisplay transceiver alarm interface
RX loss of signal: Incoming (RX) signal is lost.
RX not ready: RX is not ready
RX CDR loss of lock: RX clock cannot be recovered.
TX fault: TX fault
TX not ready: TX is not ready.
TX CDR loss of lock: TX clock cannot be recovered.
Module not ready: Module is not ready.
APD supply fault: APD (Avalanche Photo Diode) supply fault
TEC fault: TEC (Thermoelectric Cooler) fault
Wavelength unlocked: Wavelength of optical signal exceeds the manufacturer’s tolerance.
RX power high: RX power is high.
RX power low: RX power is low.
TX power high: TX power is high.
TX power low: TX power is low.
TX bias high: TX bias current is high.
TX bias low: TX bias current is low.
Temp high: Temperature is high.
Temp low: Temperature is low.
Voltage high: Voltage is high.
Voltage low: Voltage is low.
Transceiver info I/O error: Transceiver information read and write error
Transceiver info checksum error: Transceiver information checksum error
Transceiver type and port configuration mismatch: Transceiver type does not match port configuration.
Transceiver type not supported by port hardware: Transceiver type is not sup-ported on the port.
Common-CLI-Phase-3-Sept-2012.book Page 343 Sunday, September 9, 2012 6:00 PM
2-344
Display Commandsdisplay transceiver alarm interface
Operating Notes
Possible values for HPN and H3C alarms/errors are not the same.
The following alarms/errors are not supported in H3C devices, and they will be displayed in HPN output, if present:
• WIS local fault
• Receive optical power fault
• PMA/PMD receiver local fault
• PMA/PMD transmitter local fault
• PCS receive local fault
• PCS transmit local fault
• PHY XS receive local fault
• Laser bias current fault
• Laser temperature fault
• Laser output power fault
HPN does not support the following alarms/errors, and they are not displayed in the display command output:
• RX not ready
• RX CDR loss of lock
• TX not ready
• TX CDR loss of lock
• Module not ready
• APD supply fault
• TEC fault
• Wavelength unlocked
The following values are supported on both HPN and H3C devices:
• Temp high
• Temp low
• Voltage high
• Voltage low
• TX bias high
• TX bias low
• TX power high
• TX power low
• RX power high
Common-CLI-Phase-3-Sept-2012.book Page 344 Sunday, September 9, 2012 6:00 PM
2-345
Display Commandsdisplay transceiver alarm interface
• RX power low
• Transceiver info I/O error
• Transceiver info checksum error
• Transceiver type and port configuration mismatch
• Transceiver type not supported by port hardware
• RX loss of signal
• TX fault
For more information on transceivers, see the “Troubleshooting” chapter in the latest Management and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show interfaces transceiver 23 detail
Transceiver in 23 Interface Index : 24 Type : 10GbE-LR Model : J8437A Connector type : SC Wavelength : Channel #0: 1310nm, #1:0nm, #2:0nm, #3:0nm Transfer distance : 10000m (SM) Diagnostic support : DOM Serial number : ED456SS987
Status Temperature : 32.754C TX Bias : 42.700mA TX Power : 0.5192mW, -2.847dBm RX Power : 0.0040mW, -23.979dBm
Recent Alarms:
Rx power low alarm Rx power low warning
Recent errors: Receive optical power fault PMA/PMD receiver local fault PMA/PMD transmitter local fault PCS receive local fault PHY XS transmit local fault Time stamp : Mon Mar 7 16:26:06 2011
Common-CLI-Phase-3-Sept-2012.book Page 345 Sunday, September 9, 2012 6:00 PM
2-346
Display Commandsdisplay transceiver alarm interface
display transceiver alarm interface Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
Rx not ready n/a
RX CDR loss of lock n/a
TX not ready n/a
TX CDR loss of lock n/a
Module not ready n/a
APD supply fault n/a
TEC fault n/a
Wavelength unlocked n/a
Temp high Temp high
Temp low Temp low
Voltage high Voltage high
Voltage low Voltage low
TX bias high TX bias high
TX bias low TX bias low
TX power high TX power high
TX power low Tx power low
RX power high RX power high
RX power low RX power low
RX loss of signal RX loss of signal
TX fault TX fault
Common-CLI-Phase-3-Sept-2012.book Page 346 Sunday, September 9, 2012 6:00 PM
2-347
Display Commandsdisplay transceiver diagnosis interface
display transceiver diagnosis interface
Displays the currently measured value of digital diagnosis parameters of H3C customized anti-spoofing pluggable optical transceivers.
Field Descriptions
transceiver diagnostic information: Digital diagnosis information of the trans-ceiver plugged in the interface.
Current diagnostic parameters: Current diagnostic parameters.
Temp.(°C): Digital diagnosis parameter-temperature, in °C, with the precision to 1°C.
Voltage(V): Digital diagnosis parameter-voltage, in V, with the precision to 0.01 V.
Bias(mA): Digital diagnosis parameter-bias current, in mA, with the precision to 0.01 mA.
RX power(dBM): Digital diagnosis parameter-RX power, in dBM, with the precision to 0.01 dBM.
TX power(dBM): Digital diagnosis parameter-TX power, in dBM, with the pre-cision to 0.01 dBM.
Comware Related ProVision
display transceiver diagnosis interface show interface transceiver [<port> | detail ]
HP Switch(config)# display transceiver diagnosis interface g1G1 transceiver diagnostic information: Current diagnostic parameters: Temp.(C) Voltage(V) Bias(mA) RX power(dBM) TX power(dBM) 25.000 0.0000 7.864 -inf -2.350
HP Switch(config)# display transceiver diagnosis interface g4G4 transceiver diagnostic information:Error: The transceiver does not support this function.
Common-CLI-Phase-3-Sept-2012.book Page 347 Sunday, September 9, 2012 6:00 PM
2-348
Display Commandsdisplay transceiver diagnosis interface
Operating Notes
For more information on transceivers, see the “Troubleshooting” chapter in the latest Management and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
display transceiver diagnosis interface Field Mappings.
Comware ProVision Software
transceiver diagnostic information Transceiver in
Current diagnostic parameters Status
Temp. (°C) Temperature
Voltage(V) Voltage
Bias(mA) TX Bias
HP Switch(config)# sh int transceiver 24 detailTransceiver in 24 Interface Index : 124 Type : SFP+LR Model : J9151A Connector Type : LC Wavelength : 1310nm Transfer Distance : 10.0km (9um), Diagnostic Support : DOM Serial Number : CN847GV009
Status Temperature : 35.148C Voltage : 3.2348V Tx Bias : 41.952mA Tx Power : 0.4047mW, -3.929dBm Rx Power : 0.0006mW, -32.218dBm
Recent Alarms : Rx power low alarm Rx power low warning
Recent Errors : Rx loss of signal
Time Stamp : Mon Jun 11 03:00:27 2012
Common-CLI-Phase-3-Sept-2012.book Page 348 Sunday, September 9, 2012 6:00 PM
2-349
Display Commandsdisplay transceiver diagnosis interface
Minimum Software Version: 15.09.
RX power(dBM) RX Power
TX power(dBM) TX Power
Comware ProVision Software
Common-CLI-Phase-3-Sept-2012.book Page 349 Sunday, September 9, 2012 6:00 PM
2-350
Display Commandsdisplay transceiver interface
display transceiver interface
Displays main parameters of a single or all pluggable transceivers.
Field Descriptions
transceiver information: Pluggable transceiver information
Connector Type: Type of the connectors of the transceiver:
• Optical connectors, including SC (SC connector, developed by NTT) and LC (LC connector, 1.25 mm/RJ-45 optical connector developed by Lucent).
• Other connectors, including RJ-45 and CX 4.
Wavelength(nm): • Optical transceiver: Central wavelength of the laser sent, in nm. If the
transceiver supports multiple wavelengths, every two wavelength values are separated by a comma.
• Electrical transceiver: Displayed as N/A.
Transfer distance(xx): Transfer distance, with xx representing km for single-mode transceivers and m for other transceivers. If the transceiver supports multiple transfer medium, every two values of the transfer distance are separated by a comma. The corresponding transfer medium is included in the bracket following the transfer distance value. The following are the transfer media:
• 9 um: 9/125 um single-mode fiber
• 50 um: 50/125 um multi-mode fiber
Comware Related ProVision
display transceiver interface show interface transceiver [<port> | detail ]
HP Switch(config)# display transceiver interface g1G1 transceiver information: Transceiver Type : 10GbE-SR Connector Type : SC Wavelength(nm) : 850nm Transfer Distance(m) : 300m (MM generic) Digital Diagnostic Monitoring : YES Vendor Name : n/a Ordering Name : J8436A
Common-CLI-Phase-3-Sept-2012.book Page 350 Sunday, September 9, 2012 6:00 PM
2-351
Display Commandsdisplay transceiver interface
• 62.5 um: 62.5/125 um multi-mode fiber
• TP: Twisted pair
• CX4: CX4 cable
Digital Diagnostic Monitoring: Whether the digital diagnosis function is sup-ported, where:
• YES: Supported
• NO: Not supported
Vendor Name: Vendor name or name of the vendor who customizes the trans-ceiver:
• H3C anti-spoofing transceiver (customized): H3C is displayed.
• Other transceivers: The vendor name is displayed; if the vendor is unknown or illegal, unknown is displayed.
Ordering Name: • H3C devices: Switch model is displayed
• Other devices: N/A is displayed.
Operating Notes
For more information on transceivers, see the “Troubleshooting” chapter in the latest Management and Configuration Guide for your switch.
Common-CLI-Phase-3-Sept-2012.book Page 351 Sunday, September 9, 2012 6:00 PM
2-352
Display Commandsdisplay transceiver interface
Example of Related ProVision Software Command Output.
display transceiver interface Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
transceiver information Transceiver in <int>
Transceiver Type Type
Connector Type Connector type
Wavelength(nm) Wavelength
Transfer distance (xx) Transfer distance
Digital Diagnostic Monitoring Diagnostic support
Vendor Name n/a
Ordering Name Model
HP Switch(config)# sh int transceiver 24 detailTransceiver in 24 Interface Index : 124 Type : SFP+LR Model : J9151A Connector Type : LC Wavelength : 1310nm Transfer Distance : 10.0km (9um), Diagnostic Support : DOM Serial Number : CN847GV009
Status Temperature : 35.148C Voltage : 3.2348V Tx Bias : 41.952mA Tx Power : 0.4047mW, -3.929dBm Rx Power : 0.0006mW, -32.218dBm
Recent Alarms : Rx power low alarm Rx power low warning
Recent Errors : Rx loss of signal
Time Stamp : Mon Jun 11 03:00:27 2012
Common-CLI-Phase-3-Sept-2012.book Page 352 Sunday, September 9, 2012 6:00 PM
2-353
Display Commandsdisplay transceiver manuinfo interface
display transceiver manuinfo interface
Displays the transceiver manufacturing information of the specified trans-ceiver on an interface or of all the interfaces in the device.
Field Descriptions
Manu. Serial Number: Serial number of the transceiver, generated during device commissioning
Manufacturing Date: Commissioning date of the transceiver, which is the date of the computer used for commissioning the switch
Vendor Name: Name of vendor who customizes the transceiver
Operating Notes
The manufacturing date is displayed in the following formats:
• Older transceivers—displayed in yyyymmdd format
• Newer transceivers—displayed in yymmddll or yymmdd format.
For more information on transceivers, see the “Troubleshooting” chapter in the latest Management and Configuration Guide for your switch.
Comware Related ProVision
display transceiver manuinfo interface show interface transceiver [<port> | detail ]
HP Switch(config)# display transceiver manuinfo interface g1G1 transceiver manufacture information: Manu. Serial Number : MY902IF107 Manufacturing Date : 081118 Vendor Name : n/a
Common-CLI-Phase-3-Sept-2012.book Page 353 Sunday, September 9, 2012 6:00 PM
2-354
Display Commandsdisplay transceiver manuinfo interface
Example of Related ProVision Software Command Output.
display transceiver diagnosis manuinfo Field Mappings.
Minimum Software Version: 15.09.
Comware ProVision Software
Manu. Serial Number Serial number
Manufacturing Date n/a
Vendor Name n/a
HP Switch(config)# sh int transceiver 24 detailTransceiver in 24 Interface Index : 124 Type : SFP+LR Model : J9151A Connector Type : LC Wavelength : 1310nm Transfer Distance : 10.0km (9um), Diagnostic Support : DOM Serial Number : CN847GV009
Status Temperature : 35.148C Voltage : 3.2348V Tx Bias : 41.952mA Tx Power : 0.4047mW, -3.929dBm Rx Power : 0.0006mW, -32.218dBm
Recent Alarms : Rx power low alarm Rx power low warning
Recent Errors : Rx loss of signal
Time Stamp : Mon Jun 11 03:00:27 2012
Common-CLI-Phase-3-Sept-2012.book Page 354 Sunday, September 9, 2012 6:00 PM
2-355
Display Commandsdisplay user-bind
display user-bind
Displays user bind address.
HP Switch# display user-bind
Total entries found: 1 MAC IP Vlan Port Status 0030c1-7f49c0 120.93.49.7 2 1
Example of Related ProVision Software Command Output.
HP Switch# show ip source-lockdown bindingsDynamic IP Lockdown (DIPLD) BindingsMac Address IP Address VLAN Port Not in HW----------- ---------- ----- ----- ---------001122-334455 10.10.10.1 1111 X11005544-332211 10.10.10.2 2222 Trk11 YES. . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
display user-bind show ip source-lockdown bindings
Common-CLI-Phase-3-Sept-2012.book Page 355 Sunday, September 9, 2012 6:00 PM
2-356
Display Commandsdisplay vlan
display vlan
Displays vlan-id for the existing vlan only. If it is consecutive it displays as a range.
HP Switch# display vlanTotal 2 VLAN exist(s).The following VLANs exist: 1(default), 7,
HP Switch# display vlan staticTotal 2 VLAN exist(s).The following VLANs exist: 1(default), 7,
HP Switch# display vlan 7VLAN ID: 7VLAN Type: staticRoute Interface: n/aDescription: VLAN 0007Name: VLAN7Tagged Ports: 3 5 7 10 16 19Untagged Ports: 8 11 18 21 22
HP Switch# display vlan 8-10
VLAN(s) do(es) not exist.
HP Switch# display vlan dynamic
No dynamic VLAN exists!
HP Switch# display vlan dynamic
Total 2 dynamic VLAN exist(s).
The following dynamic VLANs exist:
2, 4,
Minimum Software Version: 15.10.
Comware Related ProVision
display vlan No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 356 Sunday, September 9, 2012 6:00 PM
2-357
Display Commandsdisplay vrrp
display vrrp
Displays vrrp details like VLAN, status, priority, and router ip address.
HP Switch# display vrrp
IPv4 Standby Information:
Run Mode : Standard Run Method : Virtual MAC
Total number of virtual routers : 2
Interface VRID State Run Adver Auth Virtual Pri Timer Type IP -------------------------------------------------------------Vlan4 4 Initialize 144 1 None 14.4.1.1 Vlan4 5 Initialize 154 1 None 14.4.2.1
Field Descriptions:
Run Mode: Current VRRP working mode, including:
• Standard: Standard protocol mode
• Load Balance: Load balancing mode
Run Method: Current VRRP running mode, including
• Real MAC: Real MAC mode, which means the virtual IP address of the VRRP group is mapped to the real MAC address of the interface.
• Virtual MAC: Virtual MAC mode, which means the virtual IP address of the VRRP group is mapped to the virtual MAC address.
Total number of virtual routers: Number of VRRP groups
Interface: Interface to which the VRRP group belongs
VRID: ID of the VRRP group
Run Pri: Running priority of the router, or in other words, the current priority of the router. With VRRP tracking configured, when the state of the monitored interface or track entry changes, the priority of the router changes.
Comware Related ProVision
display vrrp show vrrp
Common-CLI-Phase-3-Sept-2012.book Page 357 Sunday, September 9, 2012 6:00 PM
2-358
Display Commandsdisplay vrrp
Adver. Timer: VRRP advertisement interval, in seconds
Auth Type: Authentication type, including
• None: No authentication
• Simple: Simple text authentication
• MD5: MD5 authentication
Virtual IP: Virtual IP address of the VRRP group
Example of Related ProVision Software Command Output.
HP Switch# show vrrp config
VRRP Global Configuration Information
VRRP Enabled : YesTraps Enabled : YesVirtual Routers Respond to Ping Requests : YesVRRP Nonstop Enabled: Yes
VRRP Virtual Router Configuration Information
Vlan ID : 10Virtual Router ID : 1
Administrative Status [Disabled] : EnabledMode [Uninitialized] : BackupPriority [100] : 150Advertisement Interval [1] : 1Preempt Mode [True] : TruePreempt delay time : 0Respond to Virtual IP Ping Requests [Yes] : YesPrimary IP Address : Lowest
IP Address Subnet Mask--------------- --------------- 10.0.202.87 255.255.0.0
For more information, see the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 358 Sunday, September 9, 2012 6:00 PM
2-359
Display Commandsdisplay vrrp interface <interface-type> vrid <virtual routerid>
display vrrp interface <interface-type> vrid <virtual routerid>
HP Switch# display vrrp interface vlan-interface 4 vrid 1IPv4 Standby Information: Run Mode : Standard Run Method : Virtual MAC Info: No such standby!HP-E3500-24-PoE# display vrrp interface vlan-interface 4 vrid 4 IPv4 Standby Information: Run Mode : Standard Run Method : Virtual MAC Interface VRID State Run Adver Auth Virtual Pri Timer Type IP------------------------------------------------------------- Vlan4 4 Initialize 144 1 None 14.4.1.1
Example of Related ProVision Software Command Output.
HP Switch# show vrrp vlan 2 vrid 1 configVRRP Virtual Router Configuration InformationVlan ID : 2Virtual Router ID : 1Administrative Status [Disabled] : EnabledMode [Uninitialized] : BackupPriority [100] : 150Advertisement Interval [1] : 1Preempt Mode [True] : TruePreempt delay time : 0Respond to Virtual IP Ping Requests [Yes] : YesPrimary IP Address : LowestIP Address Subnet Mask--------------- ---------------10.0.202.87 255.255.0.0
For more information, see the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display vrrp interface <interface-type> vrid <virtual routerid>
show vrrp<interface-type> vrid <virtual routerid>
Common-CLI-Phase-3-Sept-2012.book Page 359 Sunday, September 9, 2012 6:00 PM
2-360
Display Commandsdisplay vrrp statistics
display vrrp statistics
Displays vrrp counters like invalid type packets received, priority zero packets received and sent on each vrrp router configured.
HP Switch# display vrrp statistics
Interface : Vlan-interface3 VRID : 2 CheckSum Errors : 0 Version Errors : 0 Invalid Type Pkts Rcvd : 0 Advertisement Interval Errors : 0 IP TTL Errors : 0 Auth Failures : n/a Invalid Auth Type : n/a Auth Type Mismatch : 0 Packet Length Errors : 0 Address List Errors : 0 Become Master : 0 Priority Zero Pkts Rcvd : 0 Adver Rcvd : 0 Priority Zero Pkts Sent : 0 Adver Sent : n/a
Field Descriptions:
Interface: Interface to which the VRRP group belongs
VRID: Serial number of the VRRP group
CheckSum Errors: Number of packets with checksum errors
Version Errors: Number of packets with version errors
Invalid Type Pkts Rcvd: Number of packets with incorrect packet type
Advertisement Interval Errors: Number of packets with advertisement interval errors
IP TTL Errors: Number of packets with TTL errors
Auth Failures: Number of packets with authentication failures
Invalid Auth Type: Number of packets with authentication failures due to invalid authentication types
Auth Type Mismatch: Number of packets with authentication failures due to mismatching authentication types
Comware Related ProVision
display vrrp statistics show vrrp statistics
Common-CLI-Phase-3-Sept-2012.book Page 360 Sunday, September 9, 2012 6:00 PM
2-361
Display Commandsdisplay vrrp statistics
Packet Length Errors: Number of packets with VRRP packet length errors
Address List Errors: Number of packets with virtual IP address list errors
Become Master: Number of times that the router worked as the master
Priority Zero Pkts Rcvd: Number of received advertisements with the priority of 0
Advertise Rcvd: Number of received advertisements
Priority Zero Pkts Sent: Number of advertisements with the priority of 0 sent
Advertise Sent: Number of advertisements sent
Example of Related ProVision Software Command Output.
HP Switch# show vrrp statistics global
VRRP Global Statistics Information
VRRP Enabled : YesProtocol Version : 2Invalid VRID Pkts Rx : 0Checksum Error Pkts Rx : 0Bad Version Pkts Rx : 0
For more information, see the the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 361 Sunday, September 9, 2012 6:00 PM
2-362
Display Commandsdisplay vrrp statistics interface <interface-type> vrid <virtual router-id>
display vrrp statistics interface <interface-type> vrid <virtual router-id>
Displays statistics about VRRP group(s). If you specify both an interface and a VRRP group, only the statistics about the specified VRRP group on the interface are displayed. If you only specify an interface, the statistics about all the VRRP groups on the interface are displayed. If you specify neither, the statistics about all the VRRP groups on the router are displayed.
HP Switch# display vrrp statistics interface Vlan 3
Interface : Vlan-interface3VRID : 2CheckSum Errors : 0 Version Errors : 0Invalid Type Pkts Rcvd : 0 Advertisement Interval Errors : 0IP TTL Errors : 0 Auth Failures : n/aInvalid Auth Type : n/a Auth Type Mismatch : 0Packet Length Errors : 0 Address List Errors : 0Become Master : 0 Priority Zero Pkts Rcvd : 0Adver Rcvd : 0 Priority Zero Pkts Sent : 0Adver Sent : n/a
Example of Related ProVision Software Command Output.
HP Switch# show vrrp statistics globalVRRP Global Statistics InformationVRRP Enabled : YesProtocol Version : 2Invalid VRID Pkts Rx : 0Checksum Error Pkts Rx : 0Bad Version Pkts Rx : 0
For more information, see the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.09.
Comware Related ProVision
display vrrp statistics interface <interface-type> vrid <virtual router-id>
show vrrp statistics global
Common-CLI-Phase-3-Sept-2012.book Page 362 Sunday, September 9, 2012 6:00 PM
2-363
Display Commandsdisplay vrrp verbose
display vrrp verbose
Displays detailed state information of VRRP group(s). If you specify both an interface and a VRRP group, only the state information of the specified VRRP group on the interface is displayed. If you only specify an interface, the state information of all the VRRP groups on the interface is displayed. If you specify neither, the state information of all the VRRP groups on the router is displayed.
HP Switch# display vrrp verbose
IPv4 Standby Information: Run Mode : Standard Run Method : Virtual MAC Total number of virtual routers : 2
Interface Vlan-interface4 VRID : 4 Adver Timer : 1 Admin Status : UP State : Initialize Config Pri : 144 Running Pri : None Preempt Mode : YES Delay Time : 0 Auth Type : None Key : Virtual IP : 14.4.1.1 Virtual MAC : 00005e-000104 Master IP :
Interface Vlan-interface4 VRID : 5 Adver Timer : 1 Admin Status : UP State : Initialize Config Pri : 154 Running Pri : None Preempt Mode : YES Delay Time : 0 Auth Type : None Key : Virtual IP : 14.4.2.1 Virtual MAC : 00005e-000105 Master IP :
VRRP Track Information: Track Interface: Port23 State : Down Pri Reduced : n/a Track Interface: Vlan2 State : Down Pri Reduced : n/a
Comware Related ProVision
display vrrp verbose show vrrp
Common-CLI-Phase-3-Sept-2012.book Page 363 Sunday, September 9, 2012 6:00 PM
2-364
Display Commandsdisplay vrrp verbose
Example of Related ProVision Software Command Output.
HP Switch# show vrrp
VRRP Global Statistics Information
VRRP Enabled : YesProtocol Version : 2Invalid VRID Pkts Rx : 0Checksum Error Pkts Rx : 0Bad Version Pkts Rx : 0Virtual Routers Respond To Ping Requests : Yes
VRRP Virtual Router Statistics Information
Vlan ID : 2Virtual Router ID : 1State : MasterUp Time : 25 secsVirtual MAC Address : 00005e-000101Master's IP Address : 10.0.102.87Associated IP Addr Count : 1 Near Failovers : 0Advertise Pkts Rx : 0 Become Master : 1Zero Priority Rx : 0 Zero Priority Tx : 0Bad Length Pkts : 0 Bad Type Pkts : 0Mismatched Interval Pkts : 0 Mismatched Addr List Pkts : 0Mismatched IP TTL Pkts : 0 Mismatched Auth Type Pkts : 00
For more information, see the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.09.
Common-CLI-Phase-3-Sept-2012.book Page 364 Sunday, September 9, 2012 6:00 PM
3-1
Fundamental Commandsbackup startup-configuration
3
Fundamental Commands
backup startup-configuration
Used to backup the startup configuration file (used at the next system startup) to a specified TFTP server and to a specified filename.
HP Switch# backup startup-configuration to 120.93.49.9 test_newTFTP download in progress.
Related ProVision Software Command.
To upload the current startup configuration to a file named sw8200 in the config directory on drive “d” in a TFTP server with an IP address of 10.28.227.105, use the following command:HP Switch# copy startup-config tftp 10.28.227.105 d:\configs\sw8200
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
backup startup-configuration copy startup-config tftp <ip-address> <file name>
Common-CLI-Phase-3-Sept-2012.book Page 1 Sunday, September 9, 2012 6:00 PM
3-2
Fundamental Commandsclock datetime
clock datetime
Used to set the current time and date of the device. You can leave the ss field blank when you specify the time parameters. This command accepts any input for the YYYY value. It displays the current time once the value is set. It displays a warning string if it is executed in Manager View. It is not available in Operator View, it is only available in Configure context.
HP Switch# clock datetime 8:8:8 7/7/7
Related ProVision Software Command.
HP Switch# clock set
Operating Notes
For more information, refer to the latest Command Line Interface Reference
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
clock datetime clock set <Time[date] | Date[Time]>
Common-CLI-Phase-3-Sept-2012.book Page 2 Sunday, September 9, 2012 6:00 PM
3-3
Fundamental Commandsclock summer-time one-off
clock summer-time one-off
This command does not differ from the related ProVision software command.
HP Switch# clock summer-time
Operating Notes
For more information, refer to the latest Command Line Interface Reference
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
clock summer-time clock summer-time
Common-CLI-Phase-3-Sept-2012.book Page 3 Sunday, September 9, 2012 6:00 PM
3-4
Fundamental Commandsclock summer-time repeating
clock summer-time repeating
This command does not differ from the related ProVision software command.
HP Switch# clock summer-time
Operating Notes
For more information, refer to the latest Command Line Interface Reference
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
clock summer-time repeating clock summer-time
Common-CLI-Phase-3-Sept-2012.book Page 4 Sunday, September 9, 2012 6:00 PM
3-5
Fundamental Commandsclock timezone
clock timezone
This command does not differ from the related ProVision software command.
HP Switch# clock timezone
Operating Notes
For more information, refer to the latest Command Line Interface Reference
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
clock timezone clock timezone
Common-CLI-Phase-3-Sept-2012.book Page 5 Sunday, September 9, 2012 6:00 PM
3-6
Fundamental Commandscommand accounting
command accounting
Used to enable command accounting.
HP Switch# command accounting
Related ProVision Software Command.
HP Switch# aaa accounting commands
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
command accounting aaa accounting commands < stop-only | interim-update > radius
Common-CLI-Phase-3-Sept-2012.book Page 6 Sunday, September 9, 2012 6:00 PM
3-7
Fundamental Commandscommand authorization
command authorization
Used to enable command authorization.
HP Switch# command authorization
Related ProVision Software Command.
HP Switch# aaa authorization commands radius
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
command authorization aaa authorization commands radius
Common-CLI-Phase-3-Sept-2012.book Page 7 Sunday, September 9, 2012 6:00 PM
3-8
Fundamental Commandscommand-alias enable
command-alias enable
Used to enable the command keyword alias function. By default, the command keyword alias function is enabled.
HP Switch# command-alias enable
Minimum Software Version: 15.10.
Comware Related ProVision
command-alias enable No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 8 Sunday, September 9, 2012 6:00 PM
3-9
Fundamental Commandscommand-alias mapping
command-alias mapping
Used to configure a command keyword alias. By default, a command keyword has no alias. By default, the command is enabled and not configurable. It is available in Manger view. It accepts "any string" (irrespective of whether it’s a valid command token or not). Cmdkey value range is 1-40 and AliasKey value range is 1-32.
HP Switch# command-alias mapping
Minimum Software Version: 15.10.
Comware Related ProVision
command-alias mapping No equivalent ProVision software command
Common-CLI-Phase-3-Sept-2012.book Page 9 Sunday, September 9, 2012 6:00 PM
3-10
Fundamental Commandscopy
copy
This command does not differ from the related ProVision software command.
HP Switch# copy config SOURCE_CONFIG_FILE_ON_SWITCH config DESTINATION_CONFIG_FILE_ON_SWITCH
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
copy copy config SOURCE_CONFIG_FILE_ON_SWITCH config DESTINATION_CONFIG_FILE_ON_SWITCH
Common-CLI-Phase-3-Sept-2012.book Page 10 Sunday, September 9, 2012 6:00 PM
3-11
Fundamental Commandsdelete <startup-config>
delete <startup-config>
Used to delete config file from the system directory. This command can be executed from any context. The keyword 'delete' tab help text lists the config files which can be deleted. The command allows only deletion of config files and not other files. It does not support wildcards (like *.txt) and file names with URL’s. Deleted files cannot be restored.
HP Switch# delete config1
Related ProVision Software Command.
HP Switch# erase config
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
delete <startup-config> erase config <file name>
Common-CLI-Phase-3-Sept-2012.book Page 11 Sunday, September 9, 2012 6:00 PM
3-12
Fundamental Commandsflow-control
flow-control
This command does not differ from the related ProVision software command.
HP Switch# flow-control
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
flow-control flow-control
Common-CLI-Phase-3-Sept-2012.book Page 12 Sunday, September 9, 2012 6:00 PM
3-13
Fundamental Commandsidle-timeout
idle-timeout
Used to set the idle-timeout timer. When it expires, user sessions are termi-nated. By default idle-timeout is disabled. The command supports only min-utes. And these minutes are the predefined set 0,1,5,10,15,20,30,60,120. The command is available in configure context. The default inactivity timer is 0 and means it is disabled.
HP Switch# idle-timeout 120
Related ProVision Software Command.
HP Switch# console inactivity-timer
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
idle-timeout console inactivity-timer
Common-CLI-Phase-3-Sept-2012.book Page 13 Sunday, September 9, 2012 6:00 PM
3-14
Fundamental Commandsquit
quit
Used to return to a lower-level view. If the current view is operator mode, this command terminates the current connection and quits the system.
HP Switch# quitDo you want to log out [y/n]?
Related ProVision Software Command.
HP Switch# exit
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
quit exit
Common-CLI-Phase-3-Sept-2012.book Page 14 Sunday, September 9, 2012 6:00 PM
3-15
Fundamental Commandsreboot
reboot
Used to reboot a module. If the slot keyword is not provided, the whole system reboots.
HP Switch# reboot slot A
Related ProVision Software Command.
HP Switch# boot
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
reboot slot <slot num> boot
Common-CLI-Phase-3-Sept-2012.book Page 15 Sunday, September 9, 2012 6:00 PM
3-16
Fundamental Commandsreset saved-configuration
reset saved-configuration
Used to delete the startup configuration file saved on the storage medium of the switch. The command can be executed in manager mode.
Related ProVision Software Command.
HP Switch# erase startup
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
reset saved-configuration erase startup
Common-CLI-Phase-3-Sept-2012.book Page 16 Sunday, September 9, 2012 6:00 PM
3-17
Fundamental Commandsrestore startup-configuration
restore startup-configuration
Used to download a configuration file from the specified TFTP server to the switch and specify the configuration file as the startup configuration file to be used at the next startup of the switch. The command is supported in manager mode. When you download a config file from a remote server which has same name as current active startup config file name (but both are not identical) then after downloading the file the switch reboots itself. In this case, the command triggers the download of the config file from the remote server but the next startup-configuration file is not configured.
A maximum of 3 config files can be stored on the switch. There are no restrictions on the file name.
HP Switch# restore startup-configuration from 120.93.49.9 restore_test
This will change the default configuration file to be used whenever the switch is rebooted. Continue[y/n]?
Related ProVision Software Command.
HP Switch# copy tftp startup-config
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
restore startup-configuration copy tftp startup-config
Common-CLI-Phase-3-Sept-2012.book Page 17 Sunday, September 9, 2012 6:00 PM
3-18
Fundamental Commandsreturn
return
Used to return to user view from current view (non user view), as with the hot key ctrl+Z.
HP Switch# return
Related ProVision Software Command.
HP Switch# end
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
return end
Common-CLI-Phase-3-Sept-2012.book Page 18 Sunday, September 9, 2012 6:00 PM
3-19
Fundamental Commandssave
save
Used to save the current configuration to the current startup config file. By default, the current configuration gets saved in the current start-up configu-ration file.
Related ProVision Software Command.
HP Switch# write memory
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
save write memory
Common-CLI-Phase-3-Sept-2012.book Page 19 Sunday, September 9, 2012 6:00 PM
3-20
Fundamental Commandsschedule reboot at
schedule reboot at
Used to enable the scheduled reboot function of the whole system (including all cards) at a specific time and date. The command can be executed in manager mode. The supported date form is mm/dd[/[yy]yy]. The command cannot be executed if the date is not specified and specified reboot time is earlier than the current time.
HP Switch# schedule reboot at 14:00 04/13/2012 Reload scheduled at 14:00:10 04/13/2012 (in 0 days, 0 hours, 49 minutes)System will be rebooted at the scheduled time from secondary image.Do you want to continue [y/n]?
Related ProVision Software Command.
HP Switch# reload at 12:05 01/01/2012
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
schedule reboot at reload at
Common-CLI-Phase-3-Sept-2012.book Page 20 Sunday, September 9, 2012 6:00 PM
3-21
Fundamental Commandsschedule reboot delay
schedule reboot delay
Used to enable the scheduled reboot function of the whole system (including all cards) and to set a reboot waiting time. The command can be executed in manager mode and accepts input in [[dd:]hh:]mmformat
HP Switch# schedule reboot delay 01:20 Reload scheduled in 0 days, 1 hours, 20 minutesSystem will be rebooted at the scheduled time from secondary image.Do you want to continue [y/n]?
Related ProVision Software Command.
HP Switch# reload after 04:14:00
Reload scheduled in 4 days, 14 hours, 0 minutes
This command will cause a switchover at the scheduled time to the other management module which may not be running the same software image and configurations. Do you want to continue [y/n]?
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
schedule reboot delay reload after
Common-CLI-Phase-3-Sept-2012.book Page 21 Sunday, September 9, 2012 6:00 PM
3-22
Fundamental Commandsscreen-length
screen-length
Used to set the number of lines on the next screen. This command is executed in manager mode. The range for the number of lines supported is 2-1000.
HP Switch# screen-length
Related ProVision Software Command.
HP Switch# terminal length
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
screen-length terminal length
Common-CLI-Phase-3-Sept-2012.book Page 22 Sunday, September 9, 2012 6:00 PM
3-23
Fundamental Commandsset authentication password
set authentication password
This command does not differ from the related ProVision software command.
HP Switch# set authentication password
Operating Notes
For more information, refer to the latest Command Line Interface Reference
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
set authentication password set authentication password
Common-CLI-Phase-3-Sept-2012.book Page 23 Sunday, September 9, 2012 6:00 PM
3-24
Fundamental Commandsspeed
speed
Used to set the transmission rate on the user interface. This command can be executed from configure mode. There is no default value. The lowest sup-ported value is 1200 bps. The configuration has to be saved and the switch has to be rebooted to make the configuration effective.
HP Switch# speed 9600
This command will take effect after saving the configuration and rebooting the system.
Related ProVision Software Command.
HP Switch# console baud-rate 19200
This command will take effect after saving the configuration and rebooting the system.
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
speed (user interface view) console baud-rate
Common-CLI-Phase-3-Sept-2012.book Page 24 Sunday, September 9, 2012 6:00 PM
3-25
Fundamental Commandsstartup saved-configuration
startup saved-configuration
Used to specify the configuration file to be used at the next system startup. This command can be executed in manager mode.
HP Switch# startup saved-configuration test
This will change the default configuration file to be used whenever the switch is rebooted. Continue[y/n]?
Related ProVision Software Command.
HP Switch# startup-default secondary config config2HP Switch# show config filesConfiguration files:id | act pri sec | name---+-------------+-----------------------------------------1 | * * | config12 | * | config23 | |
Operating Notes
For more information, refer to the latest Basic Configuration Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
startup saved-configuration startup-default config <config file name>
Common-CLI-Phase-3-Sept-2012.book Page 25 Sunday, September 9, 2012 6:00 PM
3-26
Fundamental Commandssysname
sysname
Used to set the name of the device. Changing device name affects the prompt of the CLI. For example, if the device name is Sysname, the prompt of the user view is <Sysname>. Special characters are not allowed.
HP Switch# sysname
Related ProVision Software Command.
HP Switch# hostname
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
sysname <name-string> hostname <name-string>
Common-CLI-Phase-3-Sept-2012.book Page 26 Sunday, September 9, 2012 6:00 PM
3-27
Fundamental Commandssystem-view
system-view
Used to enter system view from the current user view.
HP Switch# system-viewHP Switch(config)#
Related ProVision Software Command.
HP Switch# configure terminalHP Switch(config)#
Operating Notes
For more information, refer to the latest Basic Configuration Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
system-view configure terminal
Common-CLI-Phase-3-Sept-2012.book Page 27 Sunday, September 9, 2012 6:00 PM
3-28
Fundamental Commandstelnet
telnet
This command does not differ from the related ProVision software command.
HP Switch# telnet
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
telnet telnet
Common-CLI-Phase-3-Sept-2012.book Page 28 Sunday, September 9, 2012 6:00 PM
3-29
Fundamental Commandstelnet ipv6
telnet ipv6
Used to telnet to a remote IPv6 host. To stop the current Telnet login, press Ctrl+K or use the quit command. This command supports both ipv6 and ipv4 formats with the given string name.
HP Switch# telnet ipv6 hostname
HP Switch# telnet ipv6 addr
Related ProVision Software Command.
HP Switch# telnet hostname
Operating Notes
For more information, refer to the latest Basic Configuration Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
telnet ipv6 telnet
Common-CLI-Phase-3-Sept-2012.book Page 29 Sunday, September 9, 2012 6:00 PM
3-30
Fundamental Commandstelnet server enable
telnet server enable
Used to enable the Telnet server. The Telnet server is enabled by default. This command is executed in manager mode.
HP Switch# telnet server enable
Related ProVision Software Command.
HP Switch# telnet-server
Operating Notes
For more information, refer to the latest Basic Configuration Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
telnet server enable telnet-server
Common-CLI-Phase-3-Sept-2012.book Page 30 Sunday, September 9, 2012 6:00 PM
3-31
Fundamental Commandsterminal type
terminal type
Used to configure the type of terminal display under the current user interface. By default, the terminal display type is VT100. This command can be executed in manager mode. The configuration becomes effective after it is saved and the system is rebooted.
HP Switch# terminal type ansi
This command will take effect after saving the configuration and rebooting the system.
Related ProVision Software Command.
HP Switch# console terminal vt100
This command will take effect after saving the configuration and rebooting the system.
Operating Notes
For more information, refer to the latest Basic Configuration Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
terminal type console terminal
Common-CLI-Phase-3-Sept-2012.book Page 31 Sunday, September 9, 2012 6:00 PM
3-32
Fundamental Commandstftp
tftp
Used to download a specified file from the TFTP server to the local device or upload a specified local file to the TFTP server in an IPv4 network. This command can be executed only from config context. Downloading a file from the tftp server to any user given file or uploading any file to the tftp server is supported only for specific type of files. Comware command allows . In ProVision this functionality is supported only for specific type of files. The destination file parameter is mandatory.
HP Switch# tftp 120.93.49.9 put config tftp_testTFTP download in progress.HP Switch# tftp 120.93.49.9 get config2 tftp_testHP Switch# tftp 120.93.49.9 sget test tftp_testEnter [email protected]'s password:Attempting username/password authentication...00000KFile transfer terminated by user request.
Related ProVision Software Command.
HP Switch# copy tftp flash 10.29.227.13 flashDevice will be rebooted, do you want to continue [y/n]?
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
tftp copy
Common-CLI-Phase-3-Sept-2012.book Page 32 Sunday, September 9, 2012 6:00 PM
3-33
Fundamental Commandstftp ipv6
tftp ipv6
Used to download a specified file from a TFTP server or upload a specified local file to a TFTP server in an IPv6 network. This command can be executed only from config context. Downloading a file from the tftp server to any user given file or uploading any file to the tftp server is supported only for specific type of files. Comware command allows . In ProVision this functionality is supported only for specific type of files. The destination file parameter is mandatory.
HP Switch# tftp 120.93.49.9 put config tftp_testTFTP download in progress.HP Switch# tftp 120.93.49.9 get config2 tftp_testHP Switch# tftp 120.93.49.9 sget test tftp_testEnter [email protected]'s password:Attempting username/password authentication...00000K
File transfer terminated by user request.
Related ProVision Software Command.
HP Switch# copy tftp flash 10.29.227.13 flashDevice will be rebooted, do you want to continue [y/n]?
Operating Notes
For more information, refer to the latest Management and Configuration
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
tftp ipv6 copy
Common-CLI-Phase-3-Sept-2012.book Page 33 Sunday, September 9, 2012 6:00 PM
3-34
Fundamental Commandsundo
undo
Used to reset the configuration of the system.
HP Switch# undo vlan vlan-id
Related ProVision Software Command.
HP Switch# no vlan vlan-id
Operating Notes
For more information, refer to the latest Command Line Interface Reference
Guide for your switch.
Minimum Software Version: 15.10.
Comware Related ProVision
undo no vlan vlan-id
Common-CLI-Phase-3-Sept-2012.book Page 34 Sunday, September 9, 2012 6:00 PM
Index – 1
Index
A
aaa accounting commands … 3-6, 3-7accounting, show … 2-277alias, show … 2-9arp detection statistics, display … 2-4arp detection statistics, show … 2-4arp detection, display … 2-3arp ip-address, display … 2-5arp, display … 2-1arp, show … 2-1arp-protect, show … 2-3
B
backup startup-configuration … 3-1BGP … 2-105, 2-108boot set-default flash … 2-7boot system … 2-7boot-history, show … 2-340boot-loader, display … 2-6
C
CLI context levels … 1-4CLI prompts … 1-4clock datetime … 3-2clock summer-time one-off … 3-3clock summer-time repeating … 3-4clock timezone … 3-5clock, display … 2-8command accounting … 3-6command authorization … 3-7command-alias enable … 3-8command-alias mapping … 3-9command-alias, display … 2-9commands, listing … 1-4Comware software … 1-1
HPN switches … 1-1config, show … 2-291, 2-293context level … 1-4copy … 3-10counters rate, display … 2-15counters, display … 2-11cpu, show … 2-16
cpu-usage history, display … 2-17cpu-usage, display … 2-16crypto host-public-key, show … 2-274current-configuration by-linenum,
display … 2-19current-configuration configuration,
display … 2-20current-configuration interface, display … 2-21current-configuration, display … 2-18, 2-71
D
debug, show … 2-23debugging, display … 2-23default-configuration, display … 2-25delete … 3-11device, display … 2-26dhcp relay information all, display … 2-28dhcp relay information interface Vlan-interface
, display … 2-29dhcp relay statistics, display … 2-30dhcp-relay, show … 2-30dhcp-snooping binding database, display … 2-34dhcp-snooping binding, show … 2-36dhcp-snooping bindings, show … 2-106dhcp-snooping information, display … 2-35dhcp-snooping packet statistics, display … 2-37dhcp-snooping trust, display … 2-38dhcp-snooping, display … 2-36dhcp-snooping, show … 2-34, 2-38dhcpv6-relay, show … 2-117diagnostic-information, display … 2-40display command listing … 1-2dns domain dynamic, display … 2-41, 2-42dns ipv6 server, display … 2-45dns, display … 2-43documentation
latest versions … 1-xvrelease notes … 1-xv
domain name … 2-43dot1x sessions, display … 2-56dot1x statistics, display … 2-56dot1x, display … 2-47, 2-56
Common-CLI-Phase-3-Sept-2012.book Page 1 Sunday, September 9, 2012 6:00 PM
2 – Index
E
empty output … 1-5environment, display … 2-59erase config … 3-9, 3-11event log
Event Log Message Reference Guide … 1-xv
F
fan, display … 2-60field mappings … 1-3fields, not populated … 1-4fips status, display … 2-61flash, show … 2-6flow-control … 3-12
G
garp statistics interface , display … 2-62garp timer interface, display … 2-63gvrp state interface vlan , display … 2-64gvrp statistics, display … 2-66gvrp status, display … 2-67gvrp vlan-operation interface interface-type in-
terface-number, display … 2-69gvrp, show … 2-62, 2-63, 2-64, 2-66, 2-67
H
history, show … 2-70history-command, display … 2-70HP Networking
switch documentation … 1-xv
I
idle-timeout … 3-13igmp group interface vlan-interface static,
display … 2-77igmp group interface vlan-interface verbose,
display … 2-78igmp group interface vlan-interface,
display … 2-75igmp group port-info, display … 2-80igmp group static, display … 2-83igmp group verbose, display … 2-85igmp group x.x.x.x static, display … 2-86igmp group x.x.x.x verbose, display … 2-87
igmp group, display … 2-73igmp interface verbose, display … 2-91igmp interface vlan-interface , display … 2-93igmp interface, display … 2-88igmp routing table, display … 2-96int, show … 2-15interface brief down, display … 2-103interface brief, display … 2-100interface command … 2-67interface transceiver detail , show … 2-350, 2-353interface transceiver detail, show … 2-342, 2-347interface, display … 2-98interface, show … 2-11, 2-98interfaces brief, show … 2-100, 2-103ip
as-path, display … 2-105aspath-list, show … 2-105community-list, display … 2-108community-list, show … 2-108dns, show … 2-43igmp group, show … 2-73igmp groups, show … 2-73ospf interface, show … 2-201ospf virtual-link, show … 2-211ospf, show … 2-209
ip check source, display … 2-106ip client-public-key, show … 2-276ip dns, show … 2-45ip host-public-key, show … 2-274ip http, display … 2-109ip https, display … 2-110ip igmp vlan , show … 2-80, 2-83, 2-86, 2-88, 2-93,
2-96ip igmp vlan, show … 2-75ip ip-prefix, display … 2-111ip ospf link-state, show … 2-204ip ospf neighbor, show … 2-207ip ospf statistics, show … 2-198ip ospf, show … 2-213ip pim bsr, show … 2-242ip pim interface, show … 2-248, 2-250ip pim neighbor, show … 2-255, 2-257ip pim rpf-override, show … 2-195ip prefix-list, show … 2-111ip source-lockdown bindings, show … 2-355ip ssh, show … 2-310, 2-314, 2-316ip, show … 2-43ipv6 dhcp duid, display … 2-112
Common-CLI-Phase-3-Sept-2012.book Page 2 Sunday, September 9, 2012 6:00 PM
Index – 3
ipv6 dhcp relay server-address all … 2-113ipv6 dhcp relay server-address interface,
display … 2-115ipv6 dhcp relay statistics, display … 2-117ipv6 helper-address, show … 2-113, 2-115ipv6 mld vlan , show … 2-177, 2-183, 2-184, 2-187ipv6 mld vlan, show … 2-173, 2-174, 2-179, 2-181,
2-186ipv6 mld, show … 2-169ipv6 ospf3 interface, show … 2-221ipv6 ospf3 neighbor detail, show … 2-216ipv6 ospf3 neighbor detail, show … 2-234ipv6 ospf3 neighbor router-id, show … 2-230ipv6 ospf3 neighbor, show … 2-228ipv6 ospf3 statistics, show … 2-237ipv6 ospf3 virtual-link, show … 2-240ipv6 route, show … 2-120, 2-122, 2-124ipv6 routing-table ipv6-address, display … 2-122ipv6 routing-table protocol, display … 2-124ipv6 routing-table, display … 2-120
L
lacp local, show … 2-125lacp system-id, display … 2-125latest manual set … 1-5link, manual set … 1-5link-aggregation member-port, display … 2-128link-aggregation summary, display … 2-130link-aggregation verbose, display … 2-132link-aggregation, display … 2-127listing commands … 1-4lldp local-information global, display … 2-138lldp local-information interface interface-type
interface-number, display … 2-139lldp local-information, display … 2-135lldp neighbor-information brief, display … 2-141lldp neighbor-information list system-name,
display … 2-143lldp neighbor-information list, display … 2-143lldp statistics global, display … 2-146lldp statistics interface interface-type inter-
face-number, display … 2-147lldp statistics, display … 2-144lldp stats, show … 2-144, 2-146, 2-147lldp status interface interface-type interface
number, display … 2-150lldp status, display … 2-149
lldp tlv-config interface interface-type inter-
face-number, display … 2-151load-balancing … 2-127logfile buffer, display … 2-152logging, debug … 2-23logging, show … 2-152loopback-detection, display … 2-155
M
mac-address aging-time, display … 2-157mac-address multicast, display … 2-159mac-address, display … 2-156mac-address, show … 2-156mac-authentication, display … 2-160, 2-165Management Information Base
See MIB.manual set, link … 1-5memory, display … 2-167MIB
mld group interface vlan-interface verbose,
display … 2-174mld group interface vlan-interface,
display … 2-173mld group port-info, display … 2-176mld group verbose, display … 2-177mld group x.x.x.x verbose, display … 2-181mld group x.x.x.x, display … 2-179mld group, display … 2-169mld interface verbose, display … 2-184mld interface vlan-interface verbose,
display … 2-187mld interface vlan-interface, display … 2-186mld interface, display … 2-183mld routing-table, display … 2-189monitor-link group, display … 2-190multicast forwarding-table, display … 2-192Multicast Listener Discovery
See MLD.multicast routing-table static, display … 2-195multicast routing-table, display … 2-193multicast rpf-info, display … 2-197
O
osfp lsdb, display … 2-204ospf cumulative, display … 2-198ospf interface, display … 2-201
Common-CLI-Phase-3-Sept-2012.book Page 3 Sunday, September 9, 2012 6:00 PM
4 – Index
ospf peer, display … 2-207ospf routing, display … 2-209ospf vlink, display … 2-211ospfv3 area area-id peer peer-router-id,
display … 2-216ospfv3 area area-id peer verbose,
display … 2-219ospfv3 interface, display … 2-221ospfv3 lsdb statistics, display … 2-227ospfv3 lsdb, display … 2-225ospfv3 peer peer-router-id, display … 2-230ospfv3 peer statistics, display … 2-233ospfv3 peer verbose, display … 2-234ospfv3 peer, display … 2-228ospfv3 statistic, display … 2-237ospfv3 vlink, display … 2-240ospfv3, display … 2-213output differences … 1-3output, empty … 1-5
P
pim bsr-info, display … 2-242pim control-message counters, display … 2-246pim grafts, display … 2-247pim interface verbose, display … 2-250pim interface, display … 2-248pim join-prune, display … 2-254pim neighbor verbose, display … 2-257pim neighbor, display … 2-255pim routing-table, display … 2-260pim rp-info, display … 2-261poe device, display … 2-262poe interface power, display … 2-265poe interface, display … 2-263poe power-usage, display … 2-267poe-power alarm, display … 2-268poe-power switch state, display … 2-269port trunk, display … 2-270port trunking … 2-127port-access authenticator, show … 2-47port-access mac-based, show … 2-160power-over-ethernet brief, show … 2-262, 2-263,
2-265, 2-267prompts, CLI … 1-4protocol-vlan interface, display … 2-273protocol-vlan, display … 2-272ProVision Software … 1-1
ProVision software
Comware support … 1-1HPN switches … 1-1
public-key local rsa public, display … 2-274public-key peer, display … 2-276
Q
quit … 3-14
R
radius host, show … 2-277radius scheme, display … 2-277radius, show … 2-277reboot … 3-15reload … 2-7reload , show … 2-295reset saved-configuration … 3-16restore startup-configuration … 3-17return … 3-18rip process-id interface-type interface-number,
display … 2-284rip process-id ip-address mask/mask-length-
clock, display … 2-285rip process-id route peer ip-address,
display … 2-287rip process-id route, display … 2-286rip, display … 2-283rmon statistics, display … 2-288rmon statistics, show … 2-288route-policy, display … 2-289running-configuration, show … 2-18, 2-19, 2-21
S
save … 3-19saved-configuration by-linenum, display … 2-293saved-configuration, display … 2-291schedule reboot at … 3-20schedule reboot delay … 3-21schedule reboot, display … 2-295screen-length … 3-22secure-mode, show … 2-61set authentication password … 3-23sflow agent, show … 2-296sflow slot, show … 2-296sflow, display … 2-296
Common-CLI-Phase-3-Sept-2012.book Page 4 Sunday, September 9, 2012 6:00 PM
Index – 5
snmp-agent community, display … 2-298snmp-agent group, display … 2-299snmp-agent local-engineid, display … 2-302snmp-agent mib-view, display … 2-303, 2-304snmp-agent sys-info, display … 2-305snmp-agent trap-list, display … 2-306snmp-agent usm-user, display … 2-308snmp-server traps, show … 2-306snmpv3 community, show … 2-298snmpv3 engineid, show … 2-302snmpv3 group, show … 2-299, 2-303snmpv3 user, show … 2-308spanning-tree config, show … 2-327spanning-tree detail, show … 2-322, 2-324spanning-tree instance, show … 2-337spanning-tree mst-config, show … 2-335spanning-tree, show … 2-319, 2-332speed … 3-24ssh client source, display … 2-309ssh server session, display … 2-310ssh server status, display … 2-312ssh server-info, display … 2-311ssl client-policy, display … 2-314ssl server-policy, display … 2-316startup saved-configuration … 3-25startup, display … 2-318stp abnormal-port, display … 2-322stp bpdu-statistics, display … 2-324stp brief, display … 2-327stp down-port, display … 2-329stp history, display … 2-330stp instance tc slot … 2-334stp instance tc, display … 2-334stp instance, display … 2-327, 2-332stp interface GigabitEnterface, display … 2-327stp region-configuration, display … 2-335stp root, display … 2-337stp tc, display … 2-334stp, display … 2-319, 2-332sysname … 3-26system fans, show … 2-60system information, show … 2-157, 2-167, 2-305system power-supply, show … 2-268system temperature, show … 2-59system, show … 2-8system-failure, display … 2-340system-view … 3-27
T
Tab key … 1-4tacacs, show … 2-71tech, show … 2-40telnet … 3-28telnet ipv6 … 3-29telnet server enable … 3-30terminal type … 3-31tftp … 3-32tftp ipv6 … 3-33this, display … 2-341time … 2-8time, show … 2-8transceiver alarm interface, display … 2-342transceiver diagnosis interface, display … 2-347transceiver interface, display … 2-350transceiver manuinfo interface, display … 2-353trunking, port … 2-127trunks load-balance interface, show … 2-127
U
undo … 3-34uplink-failure-detection, show … 2-190user-bind, display … 2-355
V
vlan, display … 2-356vrrp interface vrid, display … 2-359vrrp statistics global, show … 2-362vrrp statistics interface vrid, display … 2-362vrrp statistics, display … 2-360vrrp statistics, show … 2-360vrrp verbose, display … 2-363vrrp vrid, show … 2-359vrrp, display … 2-357vrrp, show … 2-357, 2-363
W
warranty … 0-iii
Common-CLI-Phase-3-Sept-2012.book Page 5 Sunday, September 9, 2012 6:00 PM
Technology for better business outcomes
To learn more, visit www.hp.com/networking
© Copyright 2012 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP will not be liable for technical or editorial errors or omissions contained herein. September 2012
Manual Part Number 5998-3593
Common-CLI-Phase-3-Sept-2012.book Page 2 Sunday, September 9, 2012 6:00 PM
Top Related