Page 34(Rev. 4-07)
2. Despite the 5:1 safety factor on hoist rings, never exceed the ratedload capactiy. This safety margin is needed in case of misuse, whichcould drastically lower load capacity.
3. Tensile strength of parent material should be above 80,000 psi toachieve full load rating. For weaker material, consider through-holemounting with a nut and washer on the other side.
4. Do not allow hoist rings to bind. Use a spreader bar, if necessary,to avoid binding.
5. Do not use spacers between the hoist ring and the mounting surface.
6. Mounting surface must be flat and smooth for full contact underhoist ring. Tapped mounting holes must be perpendicular to the mount-ing surface.
7. Tighten mounting screws to the torque recommended. Periodicallycheck torque because screws could loosen in extended service. Forhoist rings not furnished with screws, mount using only high-qualitysocket-head cap screws.
8. Never lift with a hook or other device that could deform the liftingring. Do not use cable assemblies on pages 30-31 for lifting.
9. Do not apply shock loads. Always lift gradually. Repeat magnafluxtesting if shock loading ever occurs.
10. After installation, check that ring rotates and pivots freely in alldirections.
F = Force on each hoist ringW= Total weight = 4000 lbs.N = Number of hoist rings = 4A = Lifting angle
F =
If A = 70°, F = = 1064 lbs.
If A = 15°, F = = 3864 lbs.
Good
Bad
WN sinA
40004 sin70°
40004 sin15°
HOIST-RING SAFETY PRECAUTIONS
The following safety precautions apply to all lifting devices on pages36-54 and page 20. Also see these individual pages for additionalprecautions and installation guidelines.
1. IMPORTANT! The load on each hoist ring is not simply total weightdivided by the number of hoist rings. The resultant force can be signif-icantly greater at shallow lift angles and with unevenly distributedloads. In the example below,
A = 70°F = 1064 lbs.
A = 15°F = 3864 lbs.
4000 lbs.
4000 lbs.
A
F
F
A
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 35
(Rev. 7-10)
HOIST RINGSSWIVEL HOIST RINGS
Heavy-DutySwivel Hoist Rings Swivel Hoist Rings Shackle Hoist Rings Safety Hoist Rings Lifting Pins
Pages 36-40 Pages 41-45 Page 46 Page 46 Page 20
PIVOTING HOIST RINGS
Fast-Lok™Pivoting Hoist Rings Pivoting Lift Plates Plate Lifting System
Page 49 Page 49 Page 50
LIFTING EYES
Heavy-Duty Lifting Eyes Universal Lifting RingsPage 52 Page 52
HOIST-RING ACCESSORIES
Weld-InForged Shackles Forged Rings Hoist-Ring Clips Threaded Inserts Renewal Road Plates
Page 53 Page 53 Page 53 Page 54 Page 54
SIDE-PULL SWIVEL HOIST RINGS
Heavy-DutySide-Pull Hoist Rings Side-Pull Hoist Rings
Page 47 Page 48
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 36
(Rev. 12-08)
180° PIVOT
360° ROTATIONH
GF
RADIUS
EDIA
K
RETAININGRINGATHREAD
C
D
J
B
L
PN
DIA
SWIVEL HOIST RINGSALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
The original safety-engineered hoist ring. Pivots 180degrees and swivels 360 degrees simultaneously toallow lifting from any direction. Safety factor = 5:1.Black oxide finish is standard, with cadmium platingavailable as a special (add -C to part number). SwivelHoist Rings are also available in 300-series stainlesssteel, with a load rating equal to 50% of the steel ver-sion (see pages 38-39). Patent no. 3,297,293,4,705,422, and 5,848,815.
Fasten hoist rings using the installation torque specifiedin the dimension table. Always install so that the hoistring can pivot and swivel freely. Some hoist rings areavailable with a choice of bolt lengths. Use the shortestbolt length only for steel plates, the other lengths forweaker materials and for through-hole mounting with awasher and nut. See general Hoist Ring SafetyPrecautions on page 34.
STANDARD RING (USA)REPLACEMENTBOLT (WITH
RETAINING RINGCL-23041-SHRBCL-800-SHRB-1CL-800-SHRB-2CL-1000-SHRB-1CL-23318-SHRB-1CL-2500-SHRB-1CL-2500-SHRB-2CL-2500-SHRB-3CL-4000-SHRB-1CL-4000-SHRB-2CL-4000-SHRB-3CL-5000-SHRB-1CL-5000-SHRB-2CL-7000-SHRB-1CL-7000-SHRB-2CL-8000-SHRB-1CL-8000-SHRB-2CL-10000-SHRB-1CL-10000-SHRB-2CL-10000-SHRB-3CL-15000-SHRB-1CL-24000-SHRB-1
—————
INSTALLATIONTORQUE(FT-LBS)
5
7
1228
28
60
100
100
160
230
470800800
2100
43006600
P.17
.17
.17
.20
.16
.16
.16
.24
.24
.24
.35
.47
.47
1.12
1.001.09
NDIA.75
.75
.751.25
1.50
1.50
1.50
2.37
2.37
2.37
3.204.204.20
5.75
7.257.75
L2.31
2.35
2.353.31
4.24
4.24
4.24
5.80
5.80
5.80
7.7511.1211.12
14.50
17.0019.25
K.96
1.03
1.091.43
1.73
1.86
1.98
2.47
2.60
2.72
3.364.365.36
6.59
8.279.56
J1.84
1.82
1.822.58
3.52
3.52
3.52
5.06
5.06
5.06
6.508.558.55
11.67
14.1515.90
H1.00
1.00
1.001.49
2.00
2.00
2.00
3.00
3.00
3.00
3.764.874.87
6.52
8.108.60
G1.61
1.62
1.622.40
3.25
3.25
3.25
4.94
4.94
4.94
6.008.008.00
10.50
13.0014.50
F.43
.44
.44
.70
.88
.88
.88
1.40
1.40
1.40
1.752.252.25
3.00
3.754.00
EDIA3/8
3/8
3/81/2
3/4
3/4
3/4
1-1/16
1-1/16
1-1/16
1-1/41-3/41-3/4
2-1/4
2-3/43-1/4
D2.67
2.63
2.633.77
4.77
4.77
4.77
6.55
6.55
6.55
8.7312.4712.47
16.87
19.5022.09
C.71
.72
.72
.93
1.23
1.23
1.23
1.72
1.72
1.72
2.112.812.81
4.09
5.276.06
B.54.29.54.541.07.771.021.27.771.021.271.021.521.031.531.031.531.281.532.281.892.702.96
4.00
5.207.00
A1/4-20
5/16-18
3/8-161/2-13
1/2-13
5/8-11
3/4-10
3/4-10
7/8-9
1"-8
1-1/4"-71-1/2"-62"-4-1/22-1/2"-42-1/2"-83"-4
3-1/2"-4
LOADRATING(LBS)550
800
10002500
2500
4000
5000
7000
8000
10000
150002400030000
50000
75000100000
CL-23050-SHRCL-800-SHR-1CL-800-SHR-2CL-1000-SHR-1CL-23301-SHRCL-2500-SHR-1CL-2500-SHR-2CL-2500-SHR-3CL-4000-SHR-1CL-4000-SHR-2CL-4000-SHR-3CL-5000-SHR-1CL-5000-SHR-2CL-7000-SHR-1CL-7000-SHR-2CL-8000-SHR-1CL-8000-SHR-2CL-10000-SHR-1CL-10000-SHR-2CL-10000-SHR-3CL-15000-SHR-1CL-24000-SHR-1CL-30000-SHR-1CL-23503-SHRCL-23501-SHRCL-23600-SHRCL-23701-SHR
PART NO.
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 37
(Rev. 12-08)
SWIVEL HOIST RINGS
Long-ring version providesextra reach and allowsusing larger lifting hooks.
OptionalLong-Ring
Version
STANDARD RING (METRIC)INSTALLATION
TORQUE(FT-LBS)
7122759100100159230
470
800800800210042007100
P.17.17.16.16.16.24.24.24
.35
.47
.47
.471.121.001.09
NDIA.75.751.501.501.502.312.312.31
3.20
4.204.204.205.757.257.75
L2.352.354.244.244.255.805.805.80
7.75
11.1211.1211.1214.5017.0019.25
K1.021.101.701.862.012.512.662.72
3.36
4.364.865.366.618.279.56
J1.821.823.523.523.525.065.065.14
6.50
8.558.558.5511.6714.5015.90
H1.001.002.002.002.003.003.003.00
3.76
4.874.874.876.528.108.60
G1.621.623.253.253.254.944.944.80
6.00
8.008.008.0010.5013.0014.50
F.44.44.88.88.881.401.401.40
1.75
2.252.252.253.003.754.00
EDIA3/83/83/43/43/4
1-1/161-1/161
1-1/4
1-3/41-3/41-3/42-1/42-3/43-1/4
D2.632.634.774.774.776.556.556.52
8.73
12.4712.4712.4716.8719.5022.09
C.72.721.231.231.231.721.721.71
2.11
2.812.812.814.095.276.06
B.66.66.741.131.181.261.462.121.812.602.723.113.114.025.207.01
AM8M10M12M16M20M20M24M30
M30
M36M42M48M64M72M90
LOADRATING(LBS)88010002300400048006600920010000
15000
2400027000300004800069000110000
PART NO.CLM-800-SHR-2CLM-1000-SHR-1CLM-2500-SHR-1CLM-4000-SHR-2CLM-24020-SHRCLM-7000-SHR-2CLM-9000-SHR-2CLM-10000-SHR-1CLM-15000-SHR-1CLM-24042-SHRCLM-24000-SHR-1CLM-27000-SHR-1CLM-30000-SHR-1CLM-24060-SHRCLM-24062-SHRCLM-24064-SHR
LONG RING (USA)
P
.16
.16
.16
.24
.24
.24
NDIA
1.50
1.50
1.50
2.37
2.37
2.37
L
6.19
6.19
6.19
7.38
7.38
7.38
K
1.72
1.85
1.97
2.46
2.59
2.71
J
3.52
3.52
3.52
5.14
5.14
5.14
H
1.99
1.99
1.99
3.00
3.00
3.00
G
3.25
3.25
3.25
4.80
4.80
4.80
F
.88
.88
.88
1.40
1.40
1.40
EDIA
3/4
3/4
3/4
1
1
1
D
6.72
6.72
6.72
8.11
8.11
8.11
C
1.22
1.22
1.22
1.71
1.71
1.71
B.781.031.281.031.281.031.531.041.541.041.291.542.29
A
1/2-13
5/8-11
3/4-10
3/4-10
7/8-9
1"-8
LOADRATING(LBS)
2500
4000
5000
7000
8000
10000
PART NO.CL-23322-SHRCL-23323-SHRCL-23324-SHRCL-23320-SHRCL-23321-SHRCL-23325-SHRCL-23327-SHRCL-23329-SHRCL-23330-SHRCL-23328-SHRCL-23331-SHRCL-23332-SHRCL-23333-SHR
REPLACEMENTBOLT (WITH
RETAINING RING)CL-23024-SHRBCL-23025-SHRBCL-23026-SHRBCL-23022-SHRBCL-23023-SHRBCL-23027-SHRBCL-23029-SHRBCL-23122-SHRBCL-23123-SHRBCL-23121-SHRBCL-23125-SHRBCL-23126-SHRBCL-23127-SHRB
INSTALLATIONTORQUE(FT-LBS)
28
60
100
100
160
230
LONG RING (METRIC)
2759100100230230
.16
.16
.16
.24
.24
.24
1.501.501.502.372.372.37
6.196.196.197.387.387.38
1.691.852.012.502.652.89
3.523.523.525.145.145.14
1.991.991.993.003.003.00
3.253.253.254.804.804.80
.88
.88
.881.401.401.40
3/43/43/4111
6.726.726.728.118.118.11
1.221.221.221.711.711.71
.75
.941.181.141.342.13
M12M16M20M20M24M30
2300400048006600920010000
CLM-24014-SHRCLM-24018-SHRCLM-24021-SHRCLM-24023-SHRCLM-24026-SHRCLM-24032-SHR
REPLACEMENTBOLT (WITH
RETAINING RING)CLM-800-SHRB-2CLM-1000-SHRB-1CLM-2500-SHRB-1CLM-4000-SHRB-2CLM-24220-SHRBCLM-7000-SHRB-2CLM-9000-SHRB-2CLM-24230-SHRBCLM-24421-SHRBCLM-24433-SHRBCLM-24223-SHRBCLM-24232-SHRBCLM-24225-SHRBCLM-24527-SHRBCLM-24627-SHRBCLM-24727-SHRB
CLM-24212-SHRBCLM-24216-SHRBCLM-24220-SHRBCLM-24222-SHRBCLM-24224-SHRBCLM-24230-SHRB
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 38
(Rev. 1-10)
SWIVEL HOIST RINGS300-SERIES STAINLESS STEEL, PASSIVATED, 100% LIQUID-PENETRANT INSPECTED
NEWSTAINLESS
STEEL
VERSION!
180° PIVOT
360° ROTATION
Stainless steel version of our original safety-engineered hoist ring, with a load rating equal to50% of the steel version. Useful for corrosive, cryo-genic, or elevated-temperature environments.Pivots 180 degrees and swivels 360 degreessimultaneously to allow lifting from any direction.Safety factor = 5:1. Patent no. 3,297,293,4,705,422, and 5,848,815.
Fasten hoist rings using the installation torquespecified in the dimension table. Always install sothat the hoist ring can pivot and swivel freely. Somehoist rings are available with a choice of boltlengths. Use the shortest bolt length only for steelplates, the other lengths for weaker materials andfor through-hole mounting with a washer and nut.See general Hoist Ring Safety Precautions onpage 34.
Stainless Steel
STANDARD RING — STAINLESS STEEL (USA)INSTALLATION
TORQUE(FT-LBS)
2.5
3.5
614
14
30
50
50
80
115
235400400
1050
21503300
P.17
.17
.17
.20
.16
.16
.16
.24
.24
.24
.35
.47
.47
1.12
1.001.09
NDIA.75
.75
.751.25
1.50
1.50
1.50
2.37
2.37
2.37
3.204.204.20
5.75
7.257.75
L2.31
2.31
2.313.31
4.25
4.25
4.25
5.78
5.78
5.78
7.7511.1211.12
14.50
17.0019.25
K.96
1.03
1.091.43
1.72
1.85
1.97
2.46
2.59
2.71
3.364.315.31
6.59
8.279.56
J1.84
1.84
1.842.58
3.52
3.52
3.52
5.14
5.14
5.14
6.508.558.55
11.67
14.1515.90
H1.00
1.00
1.001.49
1.99
1.99
1.99
3.00
3.00
3.00
3.764.874.87
6.52
8.108.60
G1.61
1.61
1.612.40
3.25
3.25
3.25
4.80
4.80
4.80
6.008.008.00
10.50
13.0014.50
F.43
.43
.43
.70
.88
.88
.88
1.40
1.40
1.40
1.752.252.25
3.00
3.754.00
EDIA3/8
3/8
3/81/2
3/4
3/4
3/4
1
1
1
1-1/41-3/41-3/4
2-1/4
2-3/43-1/4
D2.67
2.67
2.673.77
4.78
4.78
4.78
6.52
6.52
6.52
8.7312.4712.47
16.87
19.5022.09
C.71
.71
.71
.93
1.22
1.22
1.22
1.71
1.71
1.71
2.112.812.81
4.09
5.276.06
B.54.29.54.541.07.781.031.28.781.031.281.031.531.041.541.041.291.542.291.892.702.96
4.00
5.207.00
A1/4-20
5/16-18
3/8-161/2-13
1/2-13
5/8-11
3/4-10
3/4-10
7/8-9
1"-8
1-1/4"-71-1/2"-62"-4-1/22-1/2"-42-1/2"-83"-4
3-1/2"-4
LOADRATING(LBS)275
400
5001250
1250
2000
2500
3500
4000
5000
75001200015000
25000
3750050000
PART NO.CL-29050-SHR-SCL-29051-SHR-SCL-29052-SHR-SCL-29053-SHR-SCL-29301-SHR-SCL-29004-SHR-SCL-29005-SHR-SCL-29006-SHR-SCL-29001-SHR-SCL-29002-SHR-SCL-29003-SHR-SCL-29007-SHR-SCL-29009-SHR-SCL-29102-SHR-SCL-29103-SHR-SCL-29101-SHR-SCL-29105-SHR-SCL-29106-SHR-SCL-29107-SHR-SCL-29401-SHR-SCL-29202-SHR-SCL-29200-SHR-SCL-29503-SHR-SCL-29501-SHR-SCL-29600-SHR-SCL-29701-SHR-S
H
GF
RADIUS
EDIA
K
RETAININGRINGATHREAD
C
D
J
B
L
PN
DIA
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 39
(Rev. 4-08)
SWIVEL HOIST RINGS
Long-ring version providesextra reach and allowsusing larger lifting hooks.
OptionalLong-RingVersion
STANDARD RING — STAINLESS STEEL (METRIC)
P.17.17.16.16.16.24.24.24
.35
.47
.47
.471.12
NDIA.75.751.501.501.502.312.312.31
3.20
4.204.204.205.75
L2.312.314.254.254.255.785.785.78
7.75
11.1211.1211.1214.50
K1.031.111.691.852.012.502.652.89
3.29
4.234.464.706.61
J1.841.843.523.523.525.145.145.14
6.50
8.558.558.5511.67
H1.001.002.002.002.003.003.003.00
3.76
4.874.874.876.52
G1.611.613.253.253.254.774.774.77
6.00
8.008.008.0010.50
F.43.43.88.88.881.401.401.40
1.75
2.252.252.253.00
EDIA3/83/83/43/43/4111
1.25
1.751.751.752.25
D2.672.674.784.784.786.536.536.53
8.73
12.4712.4712.4716.87
C.71.711.221.221.221.711.711.71
2.11
2.812.812.814.09
B.67.67.75.941.181.141.342.131.812.602.723.113.114.02
AM8M10M12M16M20M20M24M30
M30
M36M42M48M64
LOADRATING(LBS)440500115020002400330046005000
7500
12000135001500024000
PART NO.CLM-29808-SHR-SCLM-29810-SHR-SCLM-29812-SHR-SCLM-29816-SHR-SCLM-29820-SHR-SCLM-29822-SHR-SCLM-29824-SHR-SCLM-29830-SHR-SCLM-29840-SHR-SCLM-29842-SHR-SCLM-29850-SHR-SCLM-29852-SHR-SCLM-29854-SHR-SCLM-29860-SHR-S
LONG RING — STAINLESS STEEL (USA)
P
.16
.16
.16
.24
.24
.24
NDIA
1.50
1.50
1.50
2.37
2.37
2.37
L
6.19
6.19
6.19
7.38
7.38
7.38
K
1.72
1.85
1.97
2.46
2.59
2.71
J
3.52
3.52
3.52
5.14
5.14
5.14
H
1.99
1.99
1.99
3.00
3.00
3.00
G
3.25
3.25
3.25
4.80
4.80
4.80
F
.88
.88
.88
1.40
1.40
1.40
EDIA
3/4
3/4
3/4
1
1
1
D
6.72
6.72
6.72
8.11
8.11
8.11
C
1.22
1.22
1.22
1.71
1.71
1.71
B.781.031.281.031.281.031.531.041.541.041.291.542.29
A
1/2-13
5/8-11
3/4-10
3/4-10
7/8-9
1"-8
LOADRATING(LBS)
1250
2000
2500
3500
4000
5000
PART NO.CL-29322-SHR-SCL-29323-SHR-SCL-29324-SHR-SCL-29320-SHR-SCL-29321-SHR-SCL-29325-SHR-SCL-29327-SHR-SCL-29329-SHR-SCL-29330-SHR-SCL-29328-SHR-SCL-29331-SHR-SCL-29332-SHR-SCL-29333-SHR-S
INSTALLATIONTORQUE(FT-LBS)
14
30
50
50
80
115
LONG RING — STAINLESS STEEL (METRIC)
14305050115235
.16
.16
.16
.24
.24
.24
1.501.501.502.372.372.37
6.196.196.197.387.387.38
1.691.852.012.502.652.89
3.523.523.525.145.145.14
1.991.991.993.003.003.00
3.253.253.254.804.804.80
.88
.88
.881.401.401.40
3/43/43/4111
6.726.726.728.118.118.11
1.221.221.221.711.711.71
.75
.941.181.141.342.13
M12M16M20M20M24M30
115020002400330046005000
INSTALLATIONTORQUE(FT-LBS)
3.5614305050115115
235
4004004001050
CL-29814-SHR-SCL-29818-SHR-SCL-29821-SHR-SCL-29823-SHR-SCL-29826-SHR-S
Please contact factory
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 40
(Rev. 4-08)
NEW!
SWIVEL HOIST RINGSALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
EZ-TORQUE™ SWIVEL HOIST RINGS (USA)
Extra-large Swivel Hoist Rings with our patented EZ-TorqueTM system that allows tightening several smaller boltheads with a standard torque wrench instead of tighteningone large bolt with a special tool. Swivel Hoist Rings pivot180 degrees and swivel 360 degrees simultaneously toallow lifting from any direction. Safety factor = 5:1. Blackoxide finish is standard, with cadmium plating available as aspecial. Available in load capacities up to 250000 lbs. Patentno. 3,297,293, 4,705,422, 5,848,815, and 6,199,925. Fastenhoist rings using the installation torque specified in thedimension table. Always install so that the hoist ring canpivot and swivel freely. See general Hoist Ring SafetyPrecautions on page 34.
EZ-Torque™Swivel Hoist Rings
P.35.47.47
1.12
1.001.091.331.881.88
NDIA3.204.204.20
5.75
7.257.759.8712.3812.38
L7.7511.1211.12
14.50
17.0019.2523.8128.5028.50
K3.604.604.60
6.89
8.729.5610.4513.0013.00
J6.508.558.55
11.67
14.1515.9019.6924.0024.00
H3.764.874.87
6.52
8.108.6010.7513.0013.00
G6.08.08.0
10.5
13.014.518.022.022.0
F1.752.252.25
3.00
3.754.005.006.006.00
EDIA1-1/41-3/41-3/4
2-1/4
2-3/43-1/4455
D8.7312.4712.47
16.87
19.5022.0927.3833.0033.00
C2.112.812.81
4.09
5.276.067.509.009.00
B1.892.702.96
4.00
5.207.008.509.009.00
A1-1/4"-71-1/2"-62"-4-1/22-1/2"-42-1/2"-83"-4
3-1/2"-44-1/4"-45"-46"-4
LOADRATING(LBS)150002400030000
50000
75000100000150000200000250000
PART NO.CL-23490-SHRCL-23494-SHRCL-23290-SHRCL-23592-SHRCL-23590-SHRCL-23690-SHRCL-23790-SHRCL-23792-SHRCL-23794-SHRCL-23798-SHR
INSTALLATIONTORQUE(FT-LBS)
101823
49
9298123193207
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
HEAVY-DUTYSWIVEL HOIST RINGS
ALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
Page 41
(Rev. 4-08)
The next generation of Swivel Hoist Rings, witha heavy-duty forged steel ring. Pivots 180degrees and swivels 360 degrees simultane-ously to allow lifting from any direction. Safetyfactor = 5:1. Black oxide finish is standard, withcadmium plating available as a special. MeetsOSHA standards and Military Specification MIL-STD-1365(11) or MIL-STD-209C. Patent no.4,570,987, 4,641,986, 5,405,210, and otherpatents pending.
Fasten hoist rings using the installation torquespecified in the dimension table. Always installso that the hoist ring can pivot and swivel freely.Some hoist rings are available with a choice ofbolt lengths. Use the shortest bolt length only forsteel plates, the other lengths for weaker mate-rials and for through-hole mounting with a wash-er and nut. See general Hoist Ring SafetyPrecautions on page 34.
REPLACEMENTBOLT (WITH
RETAINING RING)CL-33152-SHRBCL-33252-SHRBCL-33254-SHRBCL-33352-SHRBCL-33354-SHRB
—CL-33554-SHRBCL-33555-SHRBCL-33556-SHRBCL-33653-SHRBCL-33654-SHRBCL-33655-SHRBCL-33754-SHRBCL-33756-SHRBCL-33119-SHRBCL-33122-SHRBCL-33123-SHRB
—CL-33121-SHRBCL-33126-SHRBCL-33125-SHRBCL-33127-SHRBCL-33419-SHRBCL-33421-SHRBCL-33429-SHRBCL-33422-SHRB
——
INSTALLATIONTORQUE(FT-LBS)
5
7
12
25
28
60
100
100
160
230
470
670800
800
P.15
.15
.15
.15
.17
.17
.17
.18
.18
.18
.32
.32
.32
.32
NDIA1.25
1.25
1.25
1.25
1.89
1.89
1.89
2.81
2.81
2.81
3.88
3.883.88
3.88
L2.98
2.98
2.98
2.98
4.75
4.75
4.75
6.62
6.62
6.62
8.12
8.128.12
8.12
K1.22
1.28
1.34
1.34
2.00
2.12
2.25
2.80
2.93
3.05
4.23
4.354.48
4.48
G2.29
2.29
2.29
2.29
3.50
3.50
3.50
5.10
5.10
5.10
6.75
6.756.75
6.75
F.65
.65
.65
.65
1.00
1.00
1.00
1.40
1.40
1.40
2.00
2.002.00
2.00
EDIA.44
.44
.44
.44
.75
.75
.75
1.00
1.00
1.00
1.25
1.251.25
1.25
STANDARD RING (USA)
D3.23
3.23
3.23
3.23
5.31
5.31
5.31
7.37
7.37
7.37
9.22
9.229.22
9.22
C.96
.96
.96
.96
1.50
1.50
1.50
2.05
2.05
2.05
2.87
2.872.87
2.87
B.56.561.06.561.061.06.751.001.25.751.001.251.001.50.951.201.45.951.201.201.452.201.882.632.632.63
2.96
A1/4-20
5/16-18
3/8-16
1/2-13
1/2-13
5/8-11
3/4-10
3/4-10
7/8-9
1"-8
1-1/4"-7
1-3/8"-61-1/2"-62"-4-1/22"-8
LOADRATING(LBS)550
800
1000
2250
2500
4000
5000
7000
8000
10000
15000
2000024000
30000
PART NO.CL-33112-SHRCL-33212-SHRCL-33214-SHRCL-33312-SHRCL-33314-SHRCL-33316-SHRCL-33512-SHRCL-33515-SHRCL-33516-SHRCL-33612-SHRCL-33614-SHRCL-33615-SHRCL-33714-SHRCL-33716-SHRCL-33108-SHRCL-33102-SHRCL-33103-SHRCL-33104-SHRCL-33101-SHRCL-33106-SHRCL-33105-SHRCL-33107-SHRCL-33402-SHRCL-33401-SHRCL-33420-SHRCL-33424-SHRCL-33427-SHRCL-33432-SHR
P
GFRADIUS
EDIA
K
L
NDIAATHREAD
RETAINING RING
B
C
D
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 42
(Rev. 4-10)
HEAVY-DUTYSWIVEL HOIST RINGS
Long-ring version providesextra reach and allowsusing larger lifting hooks.
OptionalLong-Ring
Version
STANDARD RING (METRIC)
P
.16
.16
.17
.17
.17
.18
.18
.18
.32
.32
.32
.32
NDIA
1.25
1.25
1.89
1.89
1.89
2.81
2.81
2.81
3.883.883.883.88
L
2.98
2.98
4.75
4.75
4.75
6.62
6.62
6.62
8.128.128.128.12
K
1.28
1.35
2.00
2.12
2.25
2.81
3.00
3.23
4.234.484.484.48
G
2.29
2.29
3.50
3.50
3.50
5.10
5.10
5.10
6.756.756.756.75
F
.65
.65
1.00
1.00
1.00
1.40
1.40
1.40
2.002.002.002.00
EDIA
.44
.44
.75
.75
.75
1.00
1.00
1.00
1.251.251.251.25
D
3.23
3.23
5.31
5.31
5.31
7.37
7.37
7.37
9.229.229.229.22
C
.96
.96
1.50
1.50
1.50
2.05
2.05
2.05
2.872.872.872.87
B.63.83.631.02.981.26.981.26.981.501.101.101.501.501.892.642.643.153.15
A
M8
M10
M12
M16
M20
M20
M24
M30
M30M36M42M48
LOADRATING(LBS)
880
1000
2300
4000
4800
6600
9200
10000
15000240002700030000
PART NO.CLM-34212-SHRCLM-34214-SHRCLM-34312-SHRCLM-34314-SHRCLM-34515-SHRCLM-34516-SHRCLM-34614-SHRCLM-34615-SHRCLM-34714-SHRCLM-34716-SHRCLM-34101-SHRCLM-34102-SHRCLM-34103-SHRCLM-34105-SHRCLM-34107-SHRCLM-34401-SHRCLM-34402-SHRCLM-34403-SHRCLM-34404-SHR
LONG RING (USA)
P
.17
.17
.17
.18
.18
.18
NDIA
1.89
1.89
1.89
2.81
2.81
2.81
L
6.31
6.31
6.31
8.25
8.25
8.25
K
2.00
2.12
2.25
2.80
2.93
3.05
G
3.50
3.50
3.50
5.10
5.10
5.10
F
1.00
1.00
1.00
1.40
1.40
1.40
EDIA
.75
.75
.75
1.00
1.00
1.00
D
6.87
6.87
6.87
9.00
9.00
9.00
C
1.50
1.50
1.50
2.05
2.05
2.05
B.751.001.25.751.001.251.001.50.951.201.45.951.201.201.452.20
A
1/2-13
5/8-11
3/4-10
3/4-10
7/8-9
1”-8
LOADRATING(LBS)
2500
4000
5000
7000
8000
10000
PART NO.CL-33513-SHRCL-33505-SHRCL-33517-SHRCL-33613-SHRCL-33604-SHRCL-33616-SHRCL-33715-SHRCL-33717-SHRCL-33168-SHRCL-33162-SHRCL-33163-SHRCL-33164-SHRCL-33161-SHRCL-33165-SHRCL-33166-SHRCL-33167-SHR
INSTALLATIONTORQUE(FT-LBS)
28
60
100
100
160
230
LONG RING (METRIC)
27
59
100
100
230
230
.17
.17
.17
.18
.18
.18
1.89
1.89
1.89
2.81
2.81
2.81
2.00
2.12
2.25
2.81
3.00
3.23
3.50
3.50
3.50
5.10
5.10
5.10
1.00
1.00
1.00
1.40
1.40
1.40
.75
.75
.75
1.00
1.00
1.00
6.87
6.87
6.87
9.00
9.00
9.00
1.50
1.50
1.50
2.05
2.05
2.05
.981.26.981.26.981.5011.101.101.501.501.89
M12
M16
M20
M20
M24
M30
2300
4000
4800
6600
9200
10000
CLM-34505-SHRCLM-34517-SHRCLM-34604-SHRCLM-34616-SHRCLM-34715-SHRCLM-34717-SHRCLM-34161-SHRCLM-34162-SHRCLM-34163-SHRCLM-34165-SHRCLM-34167-SHR
REPLACEMENTBOLT (WITH
RETAINING RING)CL-33554-SHRBCL-33555-SHRBCL-33556-SHRBCL-33653-SHRBCL-33654-SHRBCL-33655-SHRBCL-33754-SHRBCL-33756-SHRBCL-33119-SHRBCL-33122-SHRBCL-33123-SHRB
—CL-33121-SHRBCL-33126-SHRBCL-33125-SHRBCL-33127-SHRB
INSTALLATIONTORQUE(FT-LBS)
7
12
27
59
100
100
230
230
470800800800
6.31
6.31
6.31
8.25
8.25
8.25
ADDITIONAL
LONG-RING SIZES
NOW AVAILABLE!
REPLACEMENTBOLT (WITH
RETAINING RING)CLM-34252-SHRBCLM-34254-SHRBCLM-34352-SHRBCLM-34354-SHRBCLM-34555-SHRBCLM-34556-SHRBCLM-34654-SHRBCLM-34655-SHRBCLM-34130-SHRBCLM-34131-SHRBCLM-34120-SHRBCLM-34121-SHRBCLM-34123-SHRBCLM-34126-SHRBCLM-34127-SHRBCLM-34421-SHRBCLM-34422-SHRBCLM-24232-SHRBCLM-24225-SHRB
CLM-34555-SHRBCLM-34556-SHRBCLM-34654-SHRBCLM-34655-SHRBCLM-34130-SHRBCLM-34131-SHRBCLM-34120-SHRBCLM-34121-SHRBCLM-34123-SHRBCLM-34126-SHRBCLM-34127-SHRB
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 43
(Rev. 4-08)
Heavy-Duty Road-Plate Swivel Hoist Ringshave a shorter, larger-diameter bolt, ideal for lift-ing heavy plates. Forged alloy-steel ring pivots180 degrees and swivels 360 degrees simulta-neously to allow lifting from any direction. Safetyfactor = 5:1. Black oxide finish is standard, withcadmium plating available as a special. Patentno. 4,570,987, 4,641,986, 5,405,210, and otherpatents pending. Fasten hoist rings using theinstallation torque specified in the dimensiontable. Always install so that the hoist ring canpivot and swivel freely. See general Hoist RingSafety Precautions on page 34.
Bar-TiteTM hoist rings have a steel bar knob fortightening with a lever bar instead of a wrench.These heavy-duty hoist rings have a shorter,larger-diameter bolt, ideal for lifting heavyplates. Forged alloy-steel ring pivots 180degrees and swivels 360 degrees simultane-ously to allow lifting from any direction. Safetyfactor = 5:1. Black oxide finish is standard,with cadmium plating available as a special.Patent no. 4,570,987, 4,641,986, 5,405,210,and other patents pending. Fasten hoist ringsusing the installation torque specified in thedimension table. Always install so that thehoist ring can pivot and swivel freely. See gen-eral Hoist Ring Safety Precautions on page 34.
Heavy-Duty Road-PlateSwivel Hoist Rings
HEAVY-DUTY ROAD-PLATE SWIVEL HOIST RINGS (USA)
HEAVY-DUTY BAR-TITE™ SWIVEL HOIST RINGS (USA)
INSTALLATIONTORQUE(FT-LBS)
230
470
P
.18
.32
NDIA
2.81
3.88
K
3.05
3.91
G
5.10
6.75
F
1.40
2.00
EDIA
1.00
1.25
D
7.37
9.22
C
2.39
3.29
B1.001.501.001.50
A1-1/4"-71-1/2"-61-1/4"-71-1/2"-6
LOADRATING(LBS)
10000
15000
PART NO.CL-36660-SHRCL-36665-SHRCL-36670-SHRCL-36675-SHR
PART NO.CL-34930-SHRCL-34940-SHRCL-34950-SHRCL-34960-SHRCL-34970-SHRCL-34980-SHRCL-34935-SHRCL-34945-SHRCL-34955-SHRCL-34965-SHRCL-34975-SHRCL-34985-SHR
Heavy-Duty Bar-Tite™Swivel Hoist Rings
RINGLENGTH
STANDARDRING
LONGRING
LOADRATING(LBS)
10000
10000
A1-1/4"-7
1-1/4" COIL1-1/4" ACME1-1/2"-6
1-1/2" COIL1-1/2" ACME1-1/4"-7
1-1/4" COIL1-1/4" ACME1-1/2"-6
1-1/2" COIL1-1/2" ACME
B
1.00
1.50
1.00
1.50
C
2.05
2.05
D
7.37
9.00
EDIA
1.00
1.00
F
1.40
1.40
G
5.10
5.10
K
3.80
3.80
NDIA
2.81
2.81
P
.18
.18
INSTALLATIONTORQUE(FT-LBS)
230
230
HEAVY-DUTYSWIVEL HOIST RINGS
ALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
HEAVY-DUTYSWIVEL HOIST RINGS
ALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
Page 44
(Rev. 4-08)
Lug-LokTM hoist rings have a large-diameter lugnut for tightening without a wrench. Turn thelug nut clockwise by hand until flush with theplate, then tighten by tapping one of the lugswith a small hammer or tapper. These heavy-duty hoist rings have a shorter, larger-diameterbolt, ideal for lifting heavy plates. Forged alloy-steel ring pivots 180 degrees and swivels 360degrees simultaneously to allow lifting fromany direction. Safety factor = 5:1. Black oxidefinish is standard, with cadmium plating avail-able as a special. Patent no. 4,570,987,4,641,986, 5,405,210, and other patents pend-ing. Fasten hoist rings using the installationtorque specified in the dimension table. Alwaysinstall so that the hoist ring can pivot and swiv-el freely. See general Hoist Ring SafetyPrecautions on page 34.
These Heavy-Duty Swivel Hoist Rings aremounted by welding. Forged alloy-steel ringpivots 180 degrees and swivels 360 degreessimultaneously to allow lifting from any direc-tion. Safety factor = 5:1. Black oxide finish isstandard, with cadmium plating available as aspecial. Patent no. 4,570,987, 4,641,986,5,405,210, and other patents pending. Toinstall, weld around the entire perimeter of thebase (certified welding). Always install so thatthe hoist ring can pivot and swivel freely. Seegeneral Hoist Ring Safety Precautions on page34. Rated load capacity applies to the hoist-ring assembly only. Workpiece material mustbe capable of supporting the applicableweight.
Heavy-Duty Lug-Lok™Swivel Hoist Rings
HEAVY-DUTY LUG-LOK™ SWIVEL HOIST RINGS (USA)
Heavy-Duty Weld-MountSwivel Hoist Rings
HEAVY-DUTY WELD-MOUNT SWIVEL HOIST RINGS (USA)
PART NO.CL-36920-SHRCL-36930-SHRCL-36940-SHRCL-36925-SHRCL-36935-SHRCL-36945-SHR
LOADRATING(LBS)
10000
A1-1/4"-7
1-1/4" COIL1-1/4" ACME1-1/2"-61-1/2"COIL1-1/2" ACME
B
1.00
1.50
C
2.80
D
7.75
EDIA
1.00
F
1.40
G
5.10
K
3.05
Q
.75
R
1.41
SDIA
7.00
INSTALLATIONTORQUE(FT-LBS)
230
PART NO.CL-36640-SHRCL-36645-SHRCL-36650-SHR
LOADRATING(LBS)50001000024000
A5/8-111"-8
1-1/2"-6
C1.632.303.12
D5.477.649.50
EDIA.751.001.25
F1.001.502.00
G3.505.106.75
K2.263.424.62
P.42.56.82
Q.25.38.50
SDIA2.453.514.70
SDIA
K
ATHREAD
R
EDIA
FRADIUS
G
D
C
BQ
D
Q
C
G
K
P
ASOCKET-HEAD
CAP SCREW
FRADIUS
E DIA
SDIA
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 45
(Rev. 4-08)
HEAVY-DUTYSWIVEL HOIST RINGS
ALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
Heavy-Duty Super-CoilTM Swivel Hoist Ringsare furnished with a coil bolt, ideal for tempo-rary attachment to steel structures and con-struction material. Forged alloy-steel ring piv-ots 180 degrees and swivels 360 degreessimultaneously to allow lifting from any direc-tion. Safety factor = 5:1. Black oxide finish isstandard, with cadmium plating available as aspecial. Patent no. 4,570,987, 4,641,986,5,405,210, 5,732,991, and other patents pend-ing. Fasten hoist rings using the installationtorque specified in the dimension table. Alwaysinstall so that the hoist ring can pivot and swiv-el freely. See general Hoist Ring SafetyPrecautions on page 34.
These Heavy-Duty Swivel Hoist Rings have acenter throughhole instead of a bolt, for mount-ing with a custom anchoring system. Forgedalloy-steel ring pivots and swivels 360 degreessimultaneously to allow lifting from any direc-tion. Safety factor = 5:1. Black oxide finish isstandard, with cadmium plating available as aspecial. Patent no. 4,570,987, 4,641,986,5,405,210, and other patents pending. Ratedload capacity is based on using a bolt or studwith 180,000 psi ultimate tensile strength. If abolt with lower strength is used, or if the work-piece anchor material is incapable of supportingthe weight, then rated load capacity must bereduced accordingly. Always install so that thehoist ring can pivot and swivel freely. See gen-eral Hoist Ring Safety Precautions on page 34.
Heavy-Duty Super Coil™Swivel Hoist Rings
HEAVY-DUTY SUPER-COIL™ SWIVEL HOIST RINGS (USA)
Heavy-DutySwivel Lift Plates
HEAVY-DUTY SWIVEL LIFT PLATES
PART NO.CL-33716-SHR-CTCL-33107-SHR-CTCL-33401-SHR-CTCL-33424-SHR-CT
LOADRATING(LBS)5000100001500024000
A3/4" COIL1" COIL1-1/4" COIL1-1/2" COIL
B4.005.007.007.00
C1.502.052.872.87
D5.317.379.229.22
EDIA.751.001.251.25
F1.001.402.002.00
G3.505.106.756.75
K2.253.054.234.48
NDIA1.892.813.883.88
P.17.18.32.32
T1-1/81-1/21-7/82-1/4
INSTALLATIONTORQUE(FT-LBS)100230470800
PART NO.CL-36600-SHRCL-36605-SHRCL-36610-SHRCL-36615-SHR
LOADRATING(LBS)7000100001500024000
ADIA3/41
1-1/41-1/2
C2.392.393.293.29
D7.007.008.908.90
EDIA1.001.001.251.25
F1.401.402.002.00
G5.105.106.756.75
P.41.41.50.50
Q.18.18.32.32
SDIA5.005.007.007.00
D
B
GTHEX
FRADIUS
EDIA
K
P
ATHREADN
DIA
C
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 46
(Rev. 4-10)
SHACKLE HOIST RINGSALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
PART NO.CL-10-SHRCL-25-SHR
F1-1/41-3/4
G7/81-5/16
HDIA5/167/16
J3/8-165/8-11
K5/87/8
R13/161-1/8
INSTALLATIONTORQUE(FT-LBS)7-1042-50
REPLACEMENTSHOULDERSCREW
CL-10-SHRBCL-25-SHRB
METRIC
D5/87/8
LOADRATING(LBS)10002500
A1-1/81-5/8
B5/87/8
C1-1/21-7/8
CLM-10-SHRCLM-25-SHR
5/87/8
1-1/41-3/4
7/81-5/16
5/167/16
M10M16
.59
.7913/161-1/8
7-1042-50
CLM-10-SHRBCLM-25-SHRB
10002500
1-1/81-5/8
5/87/8
1-1/21-7/8
USA
USA
SAFETY HOIST RINGSRING: FORGED 4130 STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
BASE: FORGED 1045 STEEL, BLACK OXIDE FINISH
These swivel hoist rings are designed forpermanent mounting on tooling andequipment. Forged alloy-steel shacklepivots 180 degrees and swivels 360degrees simultaneously to allow liftingfrom any direction. Can be bolted orwelded in place. Safety factor = 5:1. Patentno. 5,823,588.
Fasten hoist ring with four grade-8 socket-head cap screws, using the installationtorque specified in the dimension table.Alternatively, install by welding around theentire perimeter of the base (certifiedwelding). Always install so that the hoistr ing can pivot and swivel freely. Seegeneral Hoist Ring Safety Precautions onpage 34.
Forged base rotates 360 degrees whilethe solid-loop forged ring pivots 180degrees, to allow lifting from any direction.High-strength shoulder screw furnished.Safety factor = 5:1. Fasten hoist ring usingthe installation torque specified in thedimension table. Always install so that thehoist ring can pivot and swivel freely. Seegeneral Hoist Ring Safety Precautions onpage 34.
L1/4-20 x 1/25/16-18 x 1/23/8-16 x 5/87/16-14 x 3/45/8-11 x 1
3/4-10 x 1-1/47/8-9 x 2
KDIA2.102.402.903.504.605.406.10
J2.172.512.803.534.715.096.51
HDIA1.561.762.102.563.404.004.50
G.911.161.211.512.062.612.91
F.40.52.52.64.901.141.30
E1.431.761.912.413.314.014.51
D.38.44.50.69.971.251.38
C1.782.032.312.944.035.165.75
B2.963.553.914.976.858.759.68
A1.031.161.311.692.282.913.25
NOMINALSHACKLESIZE3/87/161/25/87/81-1/81-1/4
LOADRATING(LBS)2000300040006500130001900024000
PART NO.CL-36510-SHHRCL-36520-SHHRCL-36530-SHHRCL-36540-SHHRCL-36550-SHHRCL-36560-SHHRCL-36570-SHHR
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PART NO.CL-650-SPHRCL-800-SPHRCL-1800-SPHRCL-2500-SPHRCL-4000-SPHRCL-7000-SPHRCL-14000-SPHRCL-36143-SPHRCL-36145-SPHRCL-36148-SPHRCL-36150-SPHRCL-36155-SPHR
USA
Page 47
(Rev. 4-08)
SIDE-PULL HOIST RINGSALLOY STEEL, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
Side-Pull Hoist Rings are ideal for side mounting. Flip and turn loads without unhook-ing (use with a spreader bar). Forged alloy-steel ring pivots 180 degrees and swivels360 degrees simultaneously to allow lifting from any direction. Large, weldless forgedring can accommodate larger lifting hooks. Meets OSHA standards and MilitarySpecifications MIL-STD-209C and MIL-STD-1365(11). Safety factor = 5:1. Fastenhoist ring using the installation torque specified in the dimension table. Always installso that the hoist ring can pivot and swivel freely. See general Hoist Ring SafetyPrecautions on page 34.
INSTALLATIONTORQUE(FT-LB)3.54.515255090
150
250
300
G2-5/162-5/83-1/23-7/85-3/46
6-7/8
7-7/8
8-9/16
F5/83/41
1-1/41-1/21-3/4
2
2-1/2
3-1/8
E
2
3-3/16
5
6-13/16
6-13/16
CDIA
3/8
5/8
1
1-3/8
1-1/2
DDIA
1-1/2
2-3/8
3-3/4
4-5/8
4-5/8
BDIA
2
3
4
6
5-1/4 X 10-1/2OVAL
A5/16-183/8-161/2-135/8-113/4-101"-8
1-1/4"-71-1/4"-81-1/2"-61-1/2"-82"-4-1/22"-8
LOADRATING(LBS)6508001800250041007100
14000
17000
29000
Side-Pull Hoist Rings are idealwhenever side mounting isrequired.
E
DDIA
DIAB
G
DIA
F
C
A THREAD
METRIC61220479215030053085012003000
2.132.293.324.765.075.396.547.027.497.969.22
.63
.79
.941.261.571.892.362.833.313.785.04
2
3-3/16
5
6-13/16
6-13/16
3/8
5/8
1
1-3/8
1-1/2
1-1/2
2-3/8
3-3/4
4-5/8
4-5/8
2
3
4
6
5-1/4 X 10-1/2OVAL
M8M10M12M16M20M24M30M36M42M48M64
880110019003500550077001200017000240003000055000
CLM-36710-SPHRCLM-36715-SPHRCLM-36720-SPHRCLM-36725-SPHRCLM-36730-SPHRCLM-36735-SPHRCLM-36740-SPHRCLM-36745-SPHRCLM-36748-SPHRCLM-36750-SPHRCLM-36755-SPHR
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 48
(Rev. 4-08)
HEAVY-DUTYSIDE-PULL HOIST RINGS
ALLOY STEEL, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
Heavy-Duty version of our Side-Pull Hoist Rings offersgreater load capacity in a given mounting-thread size. Side-Pull Hoist Rings are ideal for side mounting. Flip and turnloads without unhooking (use with a spreader bar). Forgedalloy-steel ring pivots and swivels 360 degrees simultane-ously to allow lifting from any direction. Safety factor = 5:1.Patent no. 6,267,422. Fasten hoist ring using the installationtorque specified in the dimension table. Always install so thatthe hoist ring can pivot and swivel freely. See general HoistRing Safety Precautions on page 34.
USA
INSTALLATIONTORQUE(FT-LBS)
7122860100100160230
P
4.25
5.62
O
5.12
6.75
N
1.25
1.62
M12.892.842.702.922.944.003.883.75
M2
3.19
4.19
L
.22
.25
KDIA
2.19
3.25
H
3.88
5.25
G
.75
.88
F
4.72
6.25
E
.48
.98
1.23
1.25
1.50
D
.50
.75
C1.331.391.531.641.782.122.252.38
B
.88
1.25
A5/16-183/8-161/2-135/8-113/4-103/4-107/8-91"-8
LOADRATING(LBS)80010002500400050007000800010000
PART NO.CL-36305-SPHRCL-36310-SPHRCL-36315-SPHRCL-36320-SPHRCL-36325-SPHRCL-36330-SPHRCL-36335-SPHRCL-36340-SPHR
METRIC7122759100100230
4.25
5.62
5.12
6.75
1.25
1.62
2.872.802.722.562.403.273.11
3.19
4.19
.20
.24
2.20
3.11
3.88
5.25
.75
.88
4.72
6.25
.55
.94
1.46
1.541.69
.50
.75
1.341.421.501.651.812.242.40
.88
1.25
M8M10M12M16M20M20M24
880100023004000480066009200
CLM-36805-SPHRCLM-36810-SPHRCLM-36815-SPHRCLM-36820-SPHRCLM-36825-SPHRCLM-36830-SPHRCLM-36835-SPHR
B
G RADIUS H
M1F
K DIA
N OM2
P
D
A THREAD SIZEE
L
C
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 49
(Rev. 7-10)
PIVOTING LIFT PLATESALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
PIVOTING HOIST RINGSRING: FORGED 4130 STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
BASE: FORGED 1045 STEEL, BLACK OXIDE FINISH
Economical hoist ring with a low profile and highload capacity. Forged base and solid-loop forgedring. Pivots a full 180 degrees, but does not rotate(install so that lifting force is applied in the pivotingdirection). Safety factor = 6:1. Fasten hoist ringwith grade-8 socket-head cap screws, using theinstallation torque specified in the dimensiontable. The smallest three sizes have two mountingholes, the largest two sizes have four. See gener-al Hoist Ring Safety Precautions on page 34.
These hoist rings have a center throughholeinstead of a bolt, for mounting with a customanchoring system. Heavy-duty forged alloy-steelring pivots a full 180 degrees, but does not rotate(install so that lifting force is applied in the pivot-ing direction). Safety factor = 5:1. Black oxide fin-ish is standard, with cadmium plating available asa special. Patent no. 4,570,987, 4,641,986,5,405,210, and other patents pending.
Rated load capacity is based on using a bolt orstud with 180,000 psi ultimate tensile strength. Ifa bolt with lower strength is used, or if the work-piece anchor material is incapable of supportingthe weight, then rated load capacity must bereduced accordingly. See general Hoist RingSafety Precautions on page 34.
S
5.00
6.62
N
3.00
4.00
G
5.10
6.75
F
1.40
2.00
EDIA
1.00
1.25
D
7.33
8.28
C
1.70
2.50
ADIA3/41
1-1/41-1/2
LOADRATING(LBS)7000100001500024000
PART NO.CL-36620-PLPCL-36625-PLPCL-36630-PLPCL-36635-PLP
D
C
S
EDIA
FOR ADIA BOLT
FRADIUS
GN
E3/47/81-1/81-3/81-7/8
F2
2-1/2345
G2-1/23-3/163-7/85
6-3/16
INSTALLATIONTORQUE(FT-LBS)4-77-1020-2520-2542-50
R1/25/83/47/81
HDIA5/163/81/23/41
DTHREAD X MIN LENGTH5/16-18x1.00 (or M8x25mm)3/8-16x1.25 (or M10x30mm)1/2-13x1.50 (or M12x40mm)1/2-13x1.75 (or M12x45mm)5/8-11x2.50 (or M16x65mm)
C1
1-1/81-1/21-5/82-1/16
B
0
1-1/4
ADIA1-3/42-1/42-5/83-1/83-5/8
LOADRATING(LBS)2000250050001200020000
PART NO.CL-20-HRCL-25-HRCL-50-HRCL-120-HRCL-200-HR
SCREWEXTENSIONBELOW BASE.58 (or 14mm).79 (or 18mm).90 (or 25mm).90 (or 23mm)1.25 (or 33mm)
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
FAST-LOK™
PLATE LIFTING SYSTEMALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH
Page 50
(Rev. 7-10)
Plate-lifting system with a weld-on base and totallyremovable shackle assembly, allowing the platesurface to remain totally free of obstructions. No toolsrequired for installing or removing the shackleassembly. To install, first insert the two-piece clevis,then attach the shackle with either the bolt provided orwith a Fast Lok™ Detent Pin. Forged alloy-steelshackle pivots a full 180 degrees, but does not rotate(install so that lifting force is applied in the pivotingdirection). Patent pending.
The hoist ring’s flat base should be permanently in-stalled by cutting a hole in the plate and welding inplace, flush with the surface. Weld around the entireperimeter of the base (certified welding). See generalHoist Ring Safety Precautions on page 34. Rated loadcapacity applies to the hoist-ring assembly only.Workpiece material must be capable of supporting theapplicable weight.
FORGED ANCHOR SHACKLE FAST-LOK™ DETENT PIN
LIFTING-SYSTEMPIN OR BOLT
DIA1.00
LIFTING-SYSTEMLOAD RATING
(LBS)10000
PART NO.CL-36551-FAS
NOMINALSHACKLESIZE7/8
LIFTING-SYSTEMPIN DIA1.00
LIFTING-SYSTEMLOAD RATING
(LBS)10000
PART NO.CL-36903-FLPS
5.83
1.00DIA
3.31
1.444.71
2.28
4.03.88
2.09
.88
151.00DIA
1.50 3.00 1.25
1.16
2.354.50
4.501.30
.65
FAST-LOK™ BASEFAST-LOK™ CLEVIS
LIFTING-SYSTEMPIN DIA1.00
LIFTING-SYSTEMLOAD RATING
(LBS)10000
PART NO.CL-36900-FLPS
LIFTING-SYSTEMPIN DIA1.00
LIFTING-SYSTEMLOAD RATING
(LBS)10000
PART NO.CL-36905-FLPS
DIA1.10
2.151.25
1.25
2.30
2.80
1.722.70
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 51
(Rev. 7-10)
2.354.50
4.501.30
.65
SCISSOR-LOK™
PLATE LIFTING SYSTEMALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH
Plate-lifting system with a weld-on base and totallyremovable shackle assembly, allowing the platesurface to remain totally free of obstructions. No toolsrequired for installing or removing the shackleassembly. To install, first insert the two-piece clevis,then attach the shackle with either the bolt provided orwith a Fast Lok™ Detent Pin. Forged alloy-steelshackle pivots a full 180 degrees, but does not rotate(install so that lifting force is applied in the pivotingdirection). Patent pending.
The hoist ring’s flat base should be permanently in-stalled by cutting a hole in the plate and welding inplace, flush with the surface. Weld around the entireperimeter of the base (certified welding). See generalHoist Ring Safety Precautions on page 34. Rated loadcapacity applies to the hoist-ring assembly only.Workpiece material must be capable of supporting theapplicable weight.
FAST-LOK™ BASESCISSOR-LOK™ TOOL
FORGED ANCHOR SHACKLE FAST-LOK™ DETENT PIN
LIFTING-SYSTEMPIN DIA1.00
LIFTING-SYSTEMLOAD RATING
(LBS)10000
PART NO.CL-36900-FLPS
LIFTING-SYSTEMPIN DIA1.00
LIFTING-SYSTEMLOAD RATING
(LBS)10000
PART NO.CL-36860-SLPS
LIFTING-SYSTEMPIN OR BOLT
DIA1.00
LIFTING-SYSTEMLOAD RATING
(LBS)10000
PART NO.CL-36551-FAS
NOMINALSHACKLESIZE7/8
LIFTING-SYSTEMPIN DIA1.00
LIFTING-SYSTEMLOAD RATING
(LBS)10000
PART NO.CL-36903-FLPS
5.83
1.00DIA
3.31
1.444.71
2.28
4.03.88
2.09
.88
151.00DIA
1.50 3.00 1.25
1.16
ForgedAnchorShackle
Fast-Lok™Detent Pin
Fast-Lok™Base
Scissor-Lok™Tool
Scissor-Lok™ Tool readyfor insertion intoFast-Lok™ Plate
NEW!
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 52
(Rev. 4-08)
HEAVY-DUTY LIFTING EYESALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
UNIVERSAL LIFTING RINGSALLOY STEEL, HEAT TREATED, BLACK OXIDE FINISH, 100% MAGNAFLUX INSPECTED
Heavy-Duty Lifting Eyes have a short, large-diameterthread, making them ideal for lifting heavy plates.Designed for straight vertical lifting only. High-tensilealloy steel. Safety factor = 5:1. Black oxide finish isstandard, with cadmium plating available as a spe-cial. Patent pending. See general Hoist Ring SafetyPrecautions on page 34.
Removable hoist ring with a forged alloy-steel shackle. Each Universal Lifting Ringfits three different thread sizes. Designedfor straight vertical lifting only. Patent no.4,557,513. See general Hoist Ring SafetyPrecautions on page 34.
USA
B
1.00
1.50
A1"-8
1" COIL1-1/4"-7
1-1/4" COIL1-1/4"-7
1-1/4" COIL1-1/2"-6
1-1/2" COIL
VERTICALLOAD RATING
(LBS)
10000
15000
PART NO.CL-36480-HDLECL-36481-HDLECL-36482-HDLECL-36483-HDLECL-36484-HDLECL-36485-HDLECL-36486-HDLECL-36487-HDLE
F
1.38
2.00
E
1.25
1.75
D
.44
.62
C
2.12
3.00
B
.50
.75
A
3.06
4.50
VERTICALLOAD CAPACITY
(LBS)4008001400260040006000
SCREWSIZES
1/4-205/16-183/8-161/2-135/8-113/4-10
S1S2S3S1S2S3
PART NO.
CL-34005-ULR
CL-34010-ULR
USA
3.00 .50
3.00 DIA1.00
6.00 DIA
1.00
2.50 RADIUS
B
ATHREAD
3
1
2D
C
A
B
S SE
F
S
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 53
(Rev. 4-08)
HOIST RING ACCESSORIES
PART NO.CL-1-HRCCL-2-HRC
FITS RINGDIAMETER3/8, 7/16, 5/83/4, 1-1/16
A1-3/81-5/8
B15/161-1/4
C5/163/4
D1/25/8
Handy holddown clip to keep Swivel HoistRings and Side-Pull Hoist Rings from rotatingwhen not in use. Spring steel, zinc plated.Available in two sizes, one fitting ring diame-ters from 3/8" to 5/8", the other fitting ringdiameters from 3/4” to 1-1/16".
High-strength weldless forged alloy-steel ring.Meets Federal Specification RR-C 271D,Type VI. Safety factor = 6:1. Heat treatedwith black oxide finish. The largest-sizeForged Ring (49000 Lbs capacity) is ovalshaped. See general Hoist Ring SafetyPrecautions on page 34.
High-strength forged alloy-steel anchorshackle. Supplied with thin-head bolt and nutwith cotter pin. Meets Federal SpecificationRR-C 271D, Type IVA, Grade A, Class 3.Safety factor = 6:1. Heat treated with blackoxide finish. See general Hoist Ring SafetyPrecautions on page 34.
HOIST-RING CLIPS
K3/87/161/25/87/81-1/81-1/4
J.911.061.191.502.092.693.00
H2.172.512.803.534.715.096.51
GDIA.44.50.63.751.001.251.38
F1.441.691.882.383.314.254.69
E.66.75.811.061.441.812.03
D1.031.161.311.692.282.913.25
C.38.44.50.69.971.251.38
B1.782.032.312.944.035.165.75
A2.492.913.284.195.837.478.25
NOMINALSHACKLESIZE3/87/161/25/87/81-1/81-1/4
LOADRATING(LBS)2000300040006500130001900024000
PART NO.CL-36511-FASCL-36521-FASCL-36531-FASCL-36541-FASCL-36551-FASCL-36561-FASCL-36571-FAS
C————
10-1/2
BDIA2346
5-1/4
ADIA3/85/81
1-3/81-1/2
LOADRATING(LBS)38006100180003000049000
PART NO.CL-36111-FRCL-36121-FRCL-36131-FRCL-36141-FRCL-36151-FR
Forged Rings
Hoist-Ring Clips
FORGED RINGS
Forged Anchor Shackles
FORGED ANCHOR SHACKLES (USA)
A
E
H
D
J
K
C
B
F
GDIA
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Page 54(Rev. 4-08x)
HOIST RING ACCESSORIES
Weld-In Threaded Inserts are ideal for installing hoist rings inroad plates and other difficult-to-handle loads. These weld-ininserts provide an easier alternative to tapping large-diameterholes. High-tensile alloy steel. Install by cutting a hole in theplate and welding in place, flush with the surface. Weld aroundthe entire perimeter of the base (certified welding). Weldinginstructions are included with each shipment. See generalHoist Ring Safety Precautions on page 34.
Renewal Road Plates are ideal for repairingthe center section of a road plate that hasexisting holes or slots from prior usage.These weld-in plates (G-50 steel) with analloy-steel threaded insert provide an easi-er alternative to tapping large-diameterholes. Install by cutting a hole in the plateand welding in place, flush with the sur-face. Weld around the entire perimeter ofthe base (certif ied welding). Weldinginstructions are included with each ship-ment. See general Hoist Ring SafetyPrecautions on page 34.
Same specifications as the round RenewalRoad Plates shown above, except with asquare shape.
PART NO.CL-36980-WTICL-36982-WTICL-36984-WTICL-36986-WTICL-36988-WTICL-36990-WTICL-36992-WTICL-36994-WTICL-36996-WTI
THREADTYPEUNCUNCUNCCOILACMEUNCCOILACMEUNC
A3/4-101"-8
1-1/4"-71-1/4" COIL1-1/4" ACME1-1/2"-6
1-1/2" COIL1-1/2" ACME2"-4-1/2
BDIA
3
3-1/2
CDIA
2-1/8
2-3/8
D
1
1-1/2
E
1/8
3/8
A1-1/4"-7
1-1/4" COIL1-1/2"-6
1-1/2" COIL
THREADTYPEUNCCOILUNCCOIL
PART NO.ROUND
CL-36431-RRPCL-36430-RRPCL-36451-RRPCL-36450-RRP
USA
USA
A1-1/4"-7
1-1/4" COIL1-1/2"-6
1-1/2" COIL
THREADTYPEUNCCOILUNCCOIL
PART NO.SQUARE
CL-36426-RRPCL-36425-RRPCL-36446-RRPCL-36445-RRP
USA
Weld-InThreaded Inserts
Renewal Road PlatesRound
Renewal Road PlatesSquare
ATHREAD
CDIABDIA
45E
D
8.00DIA
ATHREAD
.501.00
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
Top Related